Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 436/729 | < Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >

• Intel SASWT4I SAS/SATA Controller Question

  - by Joe Hopfgartner

  Hey there! I want to assemble a cheap storage sytem based on the Norco RPC-4020 Case. When searching for controllers I found this one: Intel® RAID Controller SASWT4I This is a quote form the Spec Sheet: Scalability. Supports up to 122 physical devices in SAS mode which is ideal for employing JBODs (Just a Bunch Of Disks) or up to 14 devices in RAID 0, 1, 1E/10E mode through direct connect device attachment or through expander backplane support. Does that mean I can attatch 14 SATA drives directly to the controller using SFF-8087 - 4x SATA breakout cables? That would be nice because then I can choose a mainboard that has 6 Onboard SATA and i can connect all 20 bays while only spending 155$ on the controller and like another 100$ on cables. Would that work? And why is it 14 and not 16 when there are 4 Ports? I am really confused about all the breakout/fanout/(edge-)expanding/multiplying/channel stuff...

  Read the article

• CPU fan turns on and off repeatedly without booting

  - by rnso

  My PC has suddenly stopped starting up. On checking with case open, the CPU fan starts running when the power is turned on, but it stops after about 2-3 seconds, restarts again after about 2-3 seconds and the loop is repeated. There is no beep and nothing appears on the screen. On searching the internet, I found there could be several reasons for this. I tried removing hard-disk, CD drive, tightening connections etc but of no avial. I also tried using a new power supply but the response is the same. Where could be the problem and how can it be solved? Thanks in advance.

  Read the article

• USB sector 0 not fount Kingston USB DT100 G2

  - by java

  Windows constantly asks me "Foramt Disk". when i go to command prompt and type format H: /fs:ntfs or format H: /fs:fat32 response: Cannot determine the number of sectors on this volume. if the benefit DISKPART detail disk Kingston DT 100 G2 USB Device Disk ID: 00000000 Type : USB Status : Online Path : 0 Target : 0 LUN ID : 0 Location Path : UNAVAILABLE Current Read-only State : No Read-only : No Boot Disk : No Pagefile Disk : No Hibernation File Disk : No Crashdump Disk : No Clustered Disk : No DISKPART detail volume Read-only : No Hidden : No No Default Drive Letter: No Shadow Copy : No Offline : No BitLocker Encrypted : No Installable : No Volume Capacity : 0 B Volume Free Space : 0 B what the problem?

  Read the article

• Puppet causes endless restarts of CUPS (how does one prevent this)

  - by Purfideas

  Hi! It makes sense, and is in fact suggested on this site, to have a critical file change trigger a service restart with puppet meta-parameters (such as notify or subscribe). For example: ## file definition for printers.conf file { "/etc/cups/printers.conf": [snip], source => "puppet:///module/etc/cups/printers.conf" } ## service definition for sshd service { 'cups': ensure => running, subscribe => File['/etc/cups/printers.conf'] } But in the case of CUPS, this triggers and endless loop of restarts; the logic works like this: Change puppetmaster's version of /etc/cups/printers.conf puppetmaster pushes new version to client, triggering cups restart cupsd restart insists on putting its own time stamp at the top of printers.conf, 'Written by cupsd...' This change will be seen as out of date, so after runinterval, we return to (1). Is there a way to suppress cupsd's need to time stamp the file? Or is there a puppet trick that could help here? Thanks!

  Read the article

• ata error: UnrecovData Handshk

  - by Aaron Digulla

  I just saw this message in my log (openSUSE 11.3, Linux 2.6.36.2): ata6.00: exception Emask 0x10 SAct 0x1 SErr 0x400100 action 0x6 frozen ata6.00: irq_stat 0x08000000, interface fatal error ata6: SError: { UnrecovData Handshk } ata6.00: failed command: WRITE FPDMA QUEUED ata6.00: cmd 61/58:00:9f:69:00/00:00:00:00:00/40 tag 0 ncq 45056 out res 40/00:04:9f:69:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) ata6.00: status: { DRDY } ata6: hard resetting link ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: configured for UDMA/133 ata6: EH complete Two questions: Which disk caused the error? I search /sys and /proc but couldn't find a way to map ata6 to a device (/dev/sdaXY) When such an error happens, does Linux retry the disk operation? Or do I have a corrupt filesystem?

  Read the article

• mod_rewrite directory path to deeper directory

  - by DA.

  I don't usually work with LAMP and am a bit stumped getting a site working locally. The site is set up to be used via localhost: 1) http://localhost/mysite However, the way the site files are physically on the server the root is located as such: 2) /var/www/mysite/trunk/site I'm trying to figure out a way where I could type #1 but have apache actually looking for the files in #2 so that all of the asset/page links in the web application work. Is mod_rewrite the solution? If so, I'm stumped on the syntax. I have this but it won't work (due, I assume, to it causing an infinite loop) RewriteRule ^mysite/ mysite/trunk/site I have a hunch I need to sprinkle on some regex?

  Read the article

• Download databasename.bak file

  - by Jordon

  I have downloaded databasename.bak file from my hosting company, when i tried to restore that DB file in SQL server 2008 it is keep on giving me following error. The media family on device 'C:\go4sharepoint_1384_8481.bak' is incorrectly formed. SQL Server cannot process this media family. RESTORE HEADERONLY is terminating abnormally. (Microsoft SQL Server, Error: 3241) According to this error and from following link http://www.sqlcoffee.com/Troubleshooting047.htm It is clear that either file i am downloading is corrupt or it is getting corrupted on the way? Any idea, why I am keep on receiving this error? I tried almost all ways but unable to fix this problem, please help me.

  Read the article

• Why do some devices seemingly need the wifi router to reboot before they can connect?

  - by CreeDorofl

  I've noticed a pattern but I'm not sure if it's a crappy router, crappy wireless device, or maybe everything is working as intended. I can wirelessly connect my office PC to the router's settings page for a day, maybe two, then afterwards I can't anymore until it's reset. Unrelated, but similar, in various places that offer free wifi, my kindle will connect fine most days, but occasionally won't unless the router is reset. After the reset, I connect ok. What's happening behind the scenes that makes a router stop allowing you to connect? Is it something on my end that's changing, or on the router's end?

  Read the article

• Solaris mounting partitions

  - by Benco

  I'm trying to mount a partition in solaris 10... bash-3.00# mount /dev/dsk/c0t0d0s3 /data mount: /dev/dsk/c0t0d0s3 is already mounted or /data is busy As far as I know c0t0d0s3 isn't already mounted elsewhere, so what's really going on here? From /etc/mnttab : /dev/dsk/c1t0d0s0 / ufs rw,intr,largefiles,logging,xattr,onerror=panic,dev=7800001285811136 /devices /devices devfs dev=4840000 1285811125 ctfs /system/contract ctfs dev=48c0001 1285811125 proc /proc proc dev=4880000 1285811125 mnttab /etc/mnttab mntfs dev=4900001 1285811125 swap /etc/svc/volatile tmpfs xattr,dev=4940001 1285811125 objfs /system/object objfs dev=4980001 1285811125 sharefs /etc/dfs/sharetab sharefs dev=49c0001 1285811125 /usr/lib/libc/libc_hwcap1.so.1 /lib/libc.so.1 lofs dev=780000 1285811131 fd /dev/fd fd rw,dev=4b40001 1285811136 swap /tmp tmpfs xattr,dev=4940002 1285811137 swap /var/run tmpfs xattr,dev=4940003 1285811137 -hosts /net autofs nosuid,indirect,ignore,nobrowse,dev=4c00001 1285811148 auto_home /home autofs indirect,ignore,nobrowse,dev=4c00002 1285811148 cordb:vold(pid530) /vol nfs ignore,noquota,dev=4bc0001 1285811149 I suspect the problem is not related to the mount point, but rather the disk slice I'm trying to mount: bash-3.00# newfs -v /dev/dsk/c0t0d0s3 /dev/rdsk/c0t0d0s3: Device busy

  Read the article

• Ubuntu server: lost prompt on monitor

  - by Richard

  Hello All, I am running Ubuntu 9.04 server edition. I have a monitor plugged into the box for occasional admin tasks. I pulled out a USB disk (without unmounting) and the screen is now full with this message: Buffer I/O error on device sdc1, logical block 7778778 I can't seem to clear the screen or get a prompt back. Doesn't appear to be registering keyboard strokes. The box is still running fine (I can ssh in from elsewhere and evrything is running as normal). Any ideas on how to clear screen and get my prompt back?

  Read the article

• Delay before booting with laptop

  - by Priednis

  I have almost the same problem as in Delay before booting? My computer is a practically new (couple months) Lenovo X200 Tablet (System Model 7449FXG). So when I press the power button, the indicator light that means "computer is on" turns on, but nothing else happens for about 5 mins, after that the computer starts booting normally. The same happens also on restart. And no USB or any other device for that matter is plugged in to the computer. And at the delay time the monitor is blank - actually not on at all.

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• adding a route entry to linux routing table

  - by netg

  hi, I have two systems with ip address say 64.103.56.1(A)(Dev name -wlan0) and 64.103.225.18(B),now what i want is , everytime I ping B from my system A, it has to be routed via a router say with address 10.0.0.251(C)(I want this to be my next hop to reach B) , but this router is on a different subnetwork than the two systems.How do I do this? /* Things I tried: I used 'route add -host B gw C wlan0', and got an error saying " no such process exist or no such device found". Tried ping C and traceroute and found the gw addr at my side is some 63.103.236.3(D), so added another entry route add -host C gw D wlan0, I was able to do this without any error! */

  Read the article

• how to stop a driver from running - it self protected and rootkit hidden

  - by Aristos

  I have this serous problem For the first time I can not stop a program from running. Something is on one laptop computer that is run as system legacy driver, and self protected and hidden on service as rootkit. Anything I try to remove fails. When a program or anti toolkit try to remove the hidden registry setting for make it stop I get this error : "a device attached to the system is not functioning" So any idea that can help me stop it from running, or even delete it on start up ? My one limitation is that the hard drive is on a laptop and I can not remove it and attact it to somewhere else. This program not let me, touch the registry, do not let me touch the file, do not let me touch the file, The move on boot fail to delete it, the rootrepeal fail to delete it, the rootkiet reveal from sysinternals fail to reveal it ! everything fails. Do how have any experience on this, or do you have any suggestion how to stop this driver from run ?

  Read the article

• Attempting to caue packet loss with netem doesn't work - possibly because of NAT (but delay does work)

  - by tomdee

  I have traffic from a WIFI access point routed via an Ubuntu box. I have two network interfaces which are NATed *filter :INPUT ACCEPT [11:690] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [37:6224] -A FORWARD -s 192.168.2.0/24 -i eth1 -o eth0 -m conntrack --ctstate NEW -j ACCEPT -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT COMMIT # Completed on Thu Mar 15 13:37:21 2012 # Generated by iptables-save v1.4.10 on Thu Mar 15 13:37:21 2012 *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -j MASQUERADE COMMIT If I run a ping app on an Android device connected to the WIFI network I can happily ping google. If I use netem to introduce some delay tc qdisc change dev eth0 root netem delay 100ms I can clearly see pings taking longer. If I use netem to introduce some packet loss tc qdisc change dev ifb0 root netem loss 50% then I see no change. Packet loss does work fine for locally generated traffic, just not for traffic coming in over the network that's being NATed. Any ideas how to sort this out?

  Read the article

• Problem reinstalling GRUB

  - by DisgruntledGoat

  I have a PC that dual-boots Ubuntu and Windows Vista. I recently reinstalled Windows Vista after some problems and now the bootloader's gone. I've been trying to follow this Ubuntu community guide but it's not working. I have Grub Legacy according to the first part (I installed Ubuntu 9.04 originally then upgraded). From the 9.04 LiveCD, I ran this: sudo grub-install --root-directory=/media/disk /dev/sda5 sda5 is the Ubuntu partition. I get this output: grub-probe: error: Cannot open `/boot/grub/device.map` [: 494: =: unexpected operator Installing GRUB to /dev/sda5 as (hd0,4)... Installation finished.No errors reported. This is the contents...(etc) (hd0) /dev/sda In the bit below, when I run setup (hd0) I get an error, "Error 17: Cannot mount selected partition" Little help?

  Read the article

• LAN cable not connected, but it is

  - by Koen

  I have a Windows XP SP2 desktop PC. It connects to the internet with a LAN cable (there's a wireless router for my laptop in between). The problem should be software because: when i tried connecting the same LAN cable to my laptop it works when i plugin the LAN cable (onboard) the green light is on and the orange light flickers when i tried the other cable (that feeds the wireless router) i have the same problem it worked a few days ago, nothing specific changed I tried removing the ethernet card from the device manager, and windows automatically reinstalled it. What could cause this? What can I try?

  Read the article

• Dynamic Subdomains

  - by crash

  On my new site I want to have dynamic subdomains. I'm trying to make it so that the subdomains use the same web root as the main domain, all under a single CodeIgniter installation. For example, subdomain.example.com would lead to example.com/subdomain, which is actually example.com/index.php/subdomain. I've already the DNS, virtual hosts set up but I"m getting caught up on the .htaccess. The effect of the linked htaccess is that when navigating to any subdomain, it gets caught up in an infinite loop. (Error log after one request.) It's the same effect for www., which should just resolve to the main domain.

  Read the article

• Resize PV on LVM

  - by Paul Tarjan

  I have this: Device Boot Start End Blocks Id System /dev/sda1 * 1 1217 9775552 83 Linux /dev/sda2 1218 60801 478608480 83 Linux And I'd like to shrink sda2 by about 10 Gigs to give some more space to sda1. sda2 is a PV on an LVM, but there is some free space in the VG so I don't have to worry about filesystem shrinking. How can I tell my LVM to move the data off of the first 10 gigs of sda2 and then redo my partition table to give it to sda1? (I don't have enough free space to just pvremove sda2, which would be the easy solution).

  Read the article

• Finding spoofed IP address on network

  - by Jared

  I have a few IP spoof dropped messages coming out of my Sonicwall firewall, we'll call them Source A and Source B. Both of these sources have the same mac address indicating they're coming from the layer 3 switch behind my firewall. Source A has an ip within a valid subnet on my network and it shows up in the ARP table of my layer 3 switch. I was able to trace the exact location and fix the issue. Source B's ip however, is not within valid subnet on my network and it's not showing up in my layer 3 switches arp table. Any idea how I can trace the location of this device within my network? Thanks in advance.

  Read the article

• Suggestions on providing HA access to an external (fibre) RAID subsystem

  - by user145198

  We are looking at upgrading our storage capacity with an external RAID subsystem that has redundant (2) fibre controllers, each controller has 4 x 8 Gbps fibre ports. I would like to make access to this storage system occur via HA Linux. Ideally I would connect 2 fibre ports from each controller into each Linux server, and then export either NFS or iSCSI via a 10 Gbe interface. I have seen plenty of references to DRBD, however all of those references tend to use block storage that is solely attached to each machine, rather than having a shared block storage device, so I am unsure if DRBD could (or should) be used in this case. Ideas?

  Read the article

• Where is IIS7 redirect occuring?

  - by neildeadman

  I have a site that is set up in IIS7 and is working (although I don't understand how). The binding is www.mysite.fr on port 80. In the root of the site there are no files but several folders. The site loads fine but I don't understand how it is loading? If I go to https://www.mysite.fr/ it redirects to https://www.mysite.fr/fr/ which redirects back to https://www.mysite.fr/ So we end up in an endless loop which fails. Using fiddler it is a 301 redirect but I have no idea where this is set! I guess it might be in the website code but as I don't know which file is loaded first, I don't know where to look! Any ideas?? All other sites are working fine...

  Read the article

• Wamp virtualhost with supporting of remote access

  - by Farid

  To cut the long story short, I've setup a Wamp server with local virtual host for domain like sample.dev, now I've bind my static IP and port 80 to my Apache and asked the client to make some changes in his hosts file and add x.x.x.x sample.dev , I've also configured my httpd virtual host like this : <VirtualHost *:80> ServerAlias sample.dev DocumentRoot 'webroot_directory' </VirtualHost> Client can reach to my web server using the direct access by ip address, but when he tries using the sample domain looks like he gets in to some infinite loop. The firewall is off too. What would be the problem?! Thanks.

  Read the article

• Server 2008 R2 Datacenter (and all other version) not detecting hardware

  - by Mitchell Skurnik

  I upgraded my ASUS KFN32-D SLI/SAS motherboard to the latest BIOS version and swapped out the 2 dual-core procs with 2 quad core procs. After installing Server 2008 Datacenter onto the system I noticed that it was not connected to the network. I open device manager and see no network adapters. I have to go up to View - Show hidden devices to even see the virtual WAN Miniport adapters. This problem happens in Vista and Windows 7 (all x64). What is even stranger is it all works in x86 mode. What in x64 could be causing windows to not even detect hardware that works in x86? Is the boot manager possibly the culprit?

  Read the article

< Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >