Search Results

Search found 12775 results on 511 pages for 'remote validation'.

Page 440/511 | < Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >

• pppd disconnects from 3G, doesn't reconnect, w/ persist set

  - by bytenik

  I am trying to configure pppd to connect to a 3G network (Sprint, in this case) and then stay connected, reconnecting automatically if the remote connection is terminated. I have enabled the persist option. My configuration file is as follows: hide-password noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/cellular" debug /dev/cell 921600 defaultroute noipdefault user " " persist maxfail 0 lcp-echo-failure 10 lcp-echo-interval 60 holdoff 5 However, when the peer disconnects the connection, pppd often waits a long time (substantially more than my holdoff) to reconnect the modem -- if it ever reconnects at all! An example log showing this: May 23 05:17:24 00270e0a8888 pppd[2408]: rcvd [LCP TermReq id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: LCP terminated by peer May 23 05:17:24 00270e0a8888 pppd[2408]: Connect time 60.1 minutes. May 23 05:17:24 00270e0a8888 pppd[2408]: Sent 0 bytes, received 0 bytes. May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down started (pid 2456) May 23 05:17:24 00270e0a8888 pppd[2408]: sent [LCP TermAck id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down finished (pid 2456), status = 0x0 May 23 05:17:24 00270e0a8888 pppd[2408]: Hangup (SIGHUP) May 23 05:17:24 00270e0a8888 pppd[2408]: Modem hangup May 23 05:17:24 00270e0a8888 pppd[2408]: Connection terminated. May 23 05:17:24 00270e0a8888 pppd[2408]: Terminating on signal 15 May 23 05:17:24 00270e0a8888 pppd[2408]: Exit. May 23 06:08:07 00270e0a8888 pppd[2500]: pppd 2.4.5 started by root, uid 0 May 23 06:08:10 00270e0a8888 pppd[2500]: Script /usr/sbin/chat -v -f /etc/chatscripts/cellular finished (pid 2530), status = 0x0 May 23 06:08:10 00270e0a8888 pppd[2500]: Serial connection established. May 23 06:08:10 00270e0a8888 pppd[2500]: using channel 11 The disconnect at the request of the peer occurs at 5:17, but the reconnect didn't happen until 6:08. I had a friend monitoring the server so I'm not certain that this wasn't a manual reconnection. Either way, it either took almost an hour to reconnect or never reconnected. Shouldn't persist + holdoff 5 cause this to automatically reconnect after 5 seconds of the link terminating?

  Read the article

• SFTP, Chroot problems on Redhat

  - by Curtis_w

  I'm having problems setting up sftp with a ChrootDirectory. I've done an equivalent setup on other distros, but for some reason I cannot get it to work on a Redhat AMI. The changes to my sshd_config file are: Subsystem sftp internal-sftp Match Group ftponly PasswordAuthentication yes X11Forwarding no ChrootDirectory %h ForceCommand internal-sftp AllowTcpForwarding no I have the concerned usere's homes at /home/user, owned by root. After connecting with a user in the ftponly group, I'm dropped into / without permissions for anything, and am unable to do anything. sftp bob@localhost Connecting to localhost... bob@localhost's password: sftp> pwd Remote working directory: / I can connect normally with users not in the ftponly group. openssh version 5.3 I've experimented with different permissions, as well as having users own their own home directory (gives a Write failed: Broken pipe error), and so far, nothing has seemed to work. I'm sure it's a permissions error, or something equally as trivial, but at this point my eyes are beginning to glaze over, and any help would be greatly appreciated. EDIT: James and Madhatter, thanks for clarifying. I was confused by chroot dropping me in /... just didn't think through it properly. I've added the appropriate directories and permissions to get read access. One other key part was enabling write access to chrooted homes: setsebool -P ssh_chroot_rw_homedirs on in order to get write access. I think I'm all set now. Thanks for the help.

  Read the article

• rsnapshot - not correctly archiving mysql databases

  - by Tiffany Walker

  My rsnapshot configuration: snapshot_root /.snapshots/ backup /home/user localhost/ backup_script /usr/local/backup_mysql.sh localhost/mysql/ Using this file: NOW=$(date +"%m-%d-%Y") # mm-dd-yyyy format FILE="" # used in a loop ### Server Setup ### #* MySQL login user name *# MUSER="root" #* MySQL login PASSWORD name *# MPASS="YOUR-PASSWORD" #* MySQL login HOST name *# MHOST="127.0.0.1" #* MySQL binaries *# MYSQL="$(which mysql)" MYSQLDUMP="$(which mysqldump)" GZIP="$(which gzip)" # get all database listing DBS="$($MYSQL -u $MUSER -h $MHOST -p$MPASS -Bse 'show databases')" # start to dump database one by one for db in $DBS do FILE=$BAK/mysql-$db.$NOW-$(date +"%T").gz # gzip compression for each backup file $MYSQLDUMP --single-transaction -u $MUSER -h $MHOST -p$MPASS $db | $GZIP -9 > $FILE done It dumps the databases under / I then tried with the following: http://bash.cyberciti.biz/backup/rsnapshot-remote-mysql-backup-shell-script/ I got: rsnapshot hourly ---------------------------------------------------------------------------- rsnapshot encountered an error! The program was invoked with these options: /usr/bin/rsnapshot hourly ---------------------------------------------------------------------------- ERROR: backup_script /usr/local/backup_mysql.sh returned 1 WARNING: Rolling back "localhost/mysql/" ls -la /.snapshots/hourly.0/localhost/mysql total 8 drwxr-xr-x 2 root root 4096 Nov 23 17:43 ./ drwxr-xr-x 4 root root 4096 Nov 23 18:20 ../ What exactly am I doing wrong? EDIT: # /usr/local/backup_mysql.sh *** Dumping MySQL Database *** Database> information_schema..cphulkd..eximstats..horde..leechprotect..logaholicDB_ns1..modsec..mysql..performance_schema..roundcube..test.. *** Backup done [ files wrote to /.snapshots/tmp/mysql] *** root@ns1 [~]# ls -la /.snapshots/tmp/mysql total 8040 drwxr-xr-x 2 root root 4096 Nov 23 18:41 ./ drwxr-xr-x 3 root root 4096 Nov 23 18:41 ../ -rw-r--r-- 1 root root 1409 Nov 23 18:41 cphulkd.18_41_45pm.gz -rw-r--r-- 1 root root 113522 Nov 23 18:41 eximstats.18_41_45pm.gz -rw-r--r-- 1 root root 4583 Nov 23 18:41 horde.18_41_45pm.gz -rw-r--r-- 1 root root 71757 Nov 23 18:41 information_schema.18_41_45pm.gz -rw-r--r-- 1 root root 692 Nov 23 18:41 leechprotect.18_41_45pm.gz -rw-r--r-- 1 root root 2603 Nov 23 18:41 logaholicDB_ns1.18_41_45pm.gz -rw-r--r-- 1 root root 745 Nov 23 18:41 modsec.18_41_45pm.gz -rw-r--r-- 1 root root 138928 Nov 23 18:41 mysql.18_41_45pm.gz -rw-r--r-- 1 root root 1831 Nov 23 18:41 performance_schema.18_41_45pm.gz -rw-r--r-- 1 root root 3610 Nov 23 18:41 roundcube.18_41_45pm.gz -rw-r--r-- 1 root root 436 Nov 23 18:41 test.18_41_47pm.gz MySQL Backup seems fine.

  Read the article

• Windows 7 pc freezes for an indeterminate amount of time after unlocking

  - by pikes

  Not sure if this type of question is appropriate for this forum, but I've tried everything I can think of to solve this problem aside from format/reinstall. I recently got a new work PC (Dell optiplex 755) with windows 7 professional x64. Standard developer software installed for .net development: VS2008, VS2005, SQL management studio, office 2007, etc. Recently I've been having this weird problem where after I lock my pc, when I try to unlock it, the screen will be black for awhile after unlocking. I can ctl+alt+del and put my password in but then it just goes black. The amount of time on the black screen seems to be related to the amount of time I am away from my PC. If only away a few minutes, it'll take about a minute to get to the desktop. If away for an hour, could take up to 15 minutes. If I lock it and go home for the night, I have to restart my PC in the morning (I've let it sit for an hour after a night of being locked and nothing happened). It doesn't do it every time but definitely the majority of the time. One weird thing I've seen is that if I remote into my machine before trying to log back in it does not do it. I uninstalled all software back to the point when I remember it started happening and it still does it. I was using this PC for a few weeks without this problem happening at all. Anyone know what my next troubleshooting steps could be? My IT department tried to fix it by moving my old profile to another disk and having me log in, effectively recreating a profile from scratch but that didn't solve it. As I said above if this isn't the right forum for these types of questions please let me know. Thanks in advance!

  Read the article

• NRPE: Unable to read output with check_connections plugin

  - by Wlodzimierz

  I'm using plugin which gives me warning or crtis with established connections. If I run it on local machine it gives: *root@graber:/usr/lib/nagios/plugins# ./check_connections -w 1 -c 5 -C sshd CRITICAL Established connections: 6* I know, I run as root. But: Rights to the file: root@graber:/usr/lib/nagios/plugins# ls -all check_connections -rwxr-xr-x 1 nagios nagios 5459 2012-07-06 10:19 check_connections /etc/sudoers: root@graber:/usr/lib/nagios/plugins# cat /etc/sudoers Defaults env_reset root ALL=(ALL:ALL) ALL %admin ALL=(ALL) ALL nagios ALL=(ALL) NOPASSWD: /usr/bin/lsof nagios ALL=(ALL) NOPASSWD: /usr/lib/nagios/plugins/ /etc/nagios/nrpe.cfg: *nrpe_user=nagios nrpe_group=nagios* *dont_blame_nrpe=1* *command_prefix=/usr/bin/sudo command[check_connections]=/usr/lib/nagios/plugins/check_connections -w 1 -c 5 -C sshd* log from remote: *2012-07-06T11:12:49+02:00 graber nrpe[25928]: Handling the connection... 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Host address is in allowed_hosts 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Host is asking for command 'check_connections' to be run... 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Running command: /usr/lib/nagios/plugins/check_connections -w 1 -c 5 -C sshd 2012-07-06T11:19:11+02:00 graber nrpe[26100]: Return Code: 2, Output: NRPE: Unable to read output* Why is this happening? I'm out of ideas, I've searched google for 2 days now :)

  Read the article

• Is it worth hiring a hacker to perform some penetration testing on my servers ?

  - by Brann

  I'm working in a small IT company with paranoid clients, so security has always been an important consideration to us ; In the past, we've already mandated two penetration testing from independent companies specialized in this area (Dionach and GSS). We've also ran some automated penetration tests using Nessus. Those two auditors were given a lot of insider information, and found almost nothing* ... While it feels comfortable to think our system is perfectly sure (and it was surely comfortable to show those reports to our clients when they performed their due diligence work), I've got a hard time believing that we've achieved a perfectly sure system, especially considering that we have no security specialist in our company (Security has always been a concern, and we're completely paranoid, which helps, but that's far as it goes!) If hackers can hack into companies that probably employ at least a few people whose sole task is to ensure their data stays private, surely they could hack into our small business, right ? Does someone have any experience in hiring an "ethical hacker"? How to find one? How much would it cost? *The only recommendation they made us was to upgrade our remote desktop protocols on two windows servers, which they were able to access because we gave them the correct non-standard port and whitelisted their IP

  Read the article

• TCP Handshake and port numbers

  - by Guido

  (I have a question about the TCP handshake and how port numbers are assigned, if this does not belong here, let me know.) Hi, I'm studying TCP/IP from the book "Internetworking with TCP/IP" by Douglas Comer. In the TCP chapter it mentions that TCP defines an "endpoint" as a pair (IP address, port number), and a connection is defined by two endpoints. This has a few implications, such as, a local TCP port could be in several connections at once, as long as there are no two from the same IP and the same remote port. This also means that the amount of established connections is almost limitless (2^16 for every IPv4 address. 2^48 in total). Now, in class, I was told that when one connects to a listening port, both sides agree on a different port to use, so the communication can happen and the listener socket remains free. This was also my belief before reading the book. Now I feel like I should obviously trust the book (It's Comer!), but is there any truth to the other explanation? Thanks

  Read the article

• Windows 7 fails to connect to the internet a few minutes after startup

  - by SageTheGreat

  Problem Earlier today, when I turned on my desktop computer, my internet connection works fine. Cryptocurrency miners connecting and hashing as usual and I can browse websites. But after a few minutes, my miner fails indicating that there is something wrong with my internet connection. Tried refreshing my browser and is stuck at "resolving host", and then presented me an error. After that, i can't browse sites anymore. But the weird thing is that the network icon in Windows 7 shows no signs of problems. Solutions Made Restarted my computer without doing anything: Problem persists. Tried using the network troubleshooter of windows: Reported no problems Stopped bonjour still no progress. Loaded windows using Last good config: still no progress. Restarted Modem: No change. Current Status I currently did a system restore to my system to a point before installing the latest update from Microsoft. Because earlier today, I installed some updates and after that, the problem started to appear. (After system restore, same problem.) Latest Programs installed before the problem MS Visual Studio 2013 (but internet still worked fine after the install). I hope someone could provide answers on this problem. It is my first time encountering this. EDIT: Additional Info OS: Windows 7 SP1 64-bit AV: Avast Free Antivirus Internet Connection Type: Ethernet It appears that my Laptop can't even connect to the machine thru Remote Desktop My laptop and phone on WiFi works fine and can connect to the internet. EDIT 2: Whenever I boot into Safe Mode, my Internet is fine.

  Read the article

• VPN Setup: Mac OS X and SonicWall

  - by noloader

  I'm trying to get VPN access up and running. The company has a SonicWall firewall/concentrator and I'm working on a Mac. I'm not sure of the SonicWall's hardware or software level. My MacBook Pro is OS X 10.8, x64, fully patched. The Mac Networking applet claims the remote server is not responding. The connection attempt subsequently fails: This is utter bullshit, as a Wireshark trace shows the Protected Mode negotiation, and then the fallback to Quick Mode: I have two questions (1) does Mac OS X VPN work in real life? (2) Are there any trustworthy (non-Apple) tools to test and diagnose the connection problem (Wireshark is a cannon and I have to interpret the results)? And a third question (off topic): what is broken in Cupertino such that so much broken software gets past their QA department? EDIT (12/14/2012): The network guy sent me "VPN Configuration Guide" (Equinox document SonicOS_Standard-6-EN). It seems an IPSec VPN now requires a Firewall Unique Identifier. Just to be sure, I revisited RFC 2409, where Main Mode, Aggressive Mode, and Quick Mode are discussed. I cannot find a reference to Firewall Unique Identifier. I think I am screwed here: I am trying to connect to a broken (non-standard) firewall, with a broken Mac OS X client. Fortunately, I can purchase VPN Tracker Personal (a {SonicWall|Equinox}-authored client) for $129US from Equinox. So much for standards....

  Read the article

• Msg 10054, Level 20, State 0, Line 0 Error when altering a stored procedure to add a couple of curso

  - by doug_w

  We have a home-rolled backup stored procedure that uses xp_cmdshell to create and clean up database backups. We have an instance that is 2005 sp3 that we are trying to deploy this script to. I am at a bit of a loss for why it is not working. When I execute the create it runs for about 30 seconds and yields the following error: Msg 10054, Level 20, State 0, Line 0 A transport-level error has occurred when sending the request to the server. (provider: TCP Provider, error: 0 - An existing connection was forcibly closed by the remote host.) In my tinkering I discovered that by removing the cursors that actually do the work it will allow me to create the stored procedure (not very helpful for me though). If I add the cursors back in using an alter the error returns. I would be curious if someone has experienced this problem and knows of a solution or work around. I am not opposed to posting the source, it is just lengthy. Things I have checked: Error Logs No dump files in the log directory Thanks in advance for the help.

  Read the article

• Cannot resolve Hostname to IP, but IP to hostname works

  - by blade

  Hi, I have deployed a bunch of windows server VMs on a cloud hosting service. These machines are all joined to a domain controller on the same service, which also hosts DNS. All of the domain-joined machines have dynamic IP (along with the DC). If I try to resolve any of the hostnames remotely, it fails. For example, I am in SQL Server Reporting Services and I need to connect to a remote server. I provide the hostname of the desired target server and this fails, but then if I provide the IP, this works. How can I pass the hostname and have this resolve to IP? Is there anything I need to look for in the DNS server? It has records of the hostnames (in forward lookup I think), but reverse is empty. Isn't it the case that forward lookup resolves ip to hostname and reverse resolves hostname to ip? Also, I don't know what he subnet mask because this is not in my control, so the machines may not be in the same subnet - can this be a cause of the problem? Where is the problem? Thanks

  Read the article

• DNS propagation delay or bad configuration?

  - by Javier Martinez

  I have been waiting the DNS propagation for almost 24 hours. I'am no impatient, but I want to know if I configured my zone good or I have any error in it. I think that is good, because if I use my server dns like my DNS secondary I can resolve and lookup host well. ; ; BIND data file for mydomain.net ; $TTL 86400 @ IN SOA mydomain.net. mydomain.net. ( 20120629 ; Serial 10800 ; Refresh 3 hours 3600 ; Retry 1 hour 604800 ; Expire 1 week 86400 ) ; Negative Cache TTL ; @ IN NS ns1 @ IN NS ns2 IN MX 10 mail ns1 IN A 5.39.X.Y ns2 IN A 5.39.X.Z There is not any errors in /var/syslog about bind daemon. Is everything correct? Do I only need to wait up to 48 hours for the right DNS propagation? My nslookup from a remote machine with the nameserver of the bind host: $ nslookup mydomain.net Server: bind-host-ip Address: bind-host-ip#53 Name: mydomain.net Address: domain-ip

  Read the article

• What does this diagnostic output mean?

  - by ChrisF

  I recently had a fault with my broadband connection. It turned out to be a fault with the ISP's or teleco's equipment. My ISP posted this diagnostic, but while I understand it in general, I'd like to to know more about the details. I'm assuming that ATM means Asynchronous Transfer Mode and PPP means Point to Point Protocol. It was this that my router was indicating as the fault. xDSL Status Test Summary Sync Status: Circuit In Sync General Information NTE Status: NTE Power Status: Unknown Bypass Status: Upstream DSL Link Information Downstream DSL Link Information Loop Loss: 9.0 17.0 SNR Margin: 25 15 Errored Seconds: 0 0 HEC Errors: 0 Cell Count: 0 0 Speed: 448 8128 TAM Status: Successfully executed operation Network Test: Sub-Test Results Layer Name Value Status Modem pass Transmitter Power (Upstream) 12.4 dBm Transmitter Power (Downstream) 8.8 dBm Upstream psd -38 dBm/Hz Downstream psd -51 dBm/Hz DSL pass Equipment Vendor Name TSTC Equipment Vendor Id n/a Equipment Vendor Revision n/a Training Time 8 s Num Syncs 1 Upstream bit rate 448 kbps Downstream bit rate 8128 kbps Upstream maximum bit rate 1108 kbps Downstream maximum bit rate 11744 kbps Upstream Attenuation 3.5 dB Downstream Attenuation 0.0 dB Upstream Noise Margin 20.0 dB Downstream Noise Margin 19.0 dB Local CRC Errors 0 Remote CRC Errors 0 Up Data Path interleaved Down Data Path interleaved Standard Used G_DMT INP INP Upstream Symbols n/a INP Upstream Delay 4 ms INP Upstream Depth 4 INP Downstream Symbols n/a INP Downstream Delay 5 ms INP Downstream Depth 32 ATM Reason: No ATM cells received fail Number of cells transmitted 30 Number of cells received 0 number of Near end HEC errors 0 number of Far end HEC errors n/a PPP Reason: No response from peer fail PAP authentication nottested CHAP authentication nottested (I'm not sure that Super User is the best place to ask this, but two people have suggested I ask it here so here I am).

  Read the article

• Can I trick Carbonite into backing up an external hard drive?

  - by Brian

  I use Carbonite to back up my PC (Windows XP). We were running low on disk space on our home PC (down to 15 GB), so I went out and purchased an external hard drive. However, Carbonite will not back it up. Is it possible to set up Carbonite to backup an external hard drive? I just want the external drive to be extra disk space. From their FAQ: The current version of Carbonite backs up only the files that reside on permanent hard drives on your computer. It will not back up network drives, external drives, and NAS (network accessed storage) drives. If there are files on a remote drive that you wish to include in your Carbonite backup, you should copy the files to a folder on your local hard drive. If the files are on a shared network drive, you could install Carbonite on the computer on which the network shared drive physically exists, and back the files up directly from that computer. Check back soon for a Carbonite service plan that will allow you to back up your external drives.

  Read the article

• Dynamic DNS Updates with Wireless and Wired interfaces

  - by Phaedrus

  We have offices full of Windows & Mac users who obtain IP addresses from a Windows DHCP server, which in turn updates Dynamic DNS entries. We are noticing major inconsistencies with the entries, and have found that the problem is occurring more on Macs than on windows, and even more when users are frequently switching from wired to wireless adapter, which makes sense, as this sequence occurs: User enables wired adapter and registers Proper DNS User enables wireless adapter and registers 2nd proper DNS entry user switches off wireless manually and 2nd entry remains improperly until scavenge. Our help desk folks rely heavily (maybe more than they should) on the dynamic entries as part of their business process. For example, the user submits a help desk ticket, and the staff member expects to be able to remote desktop to their machine by hostname, which is hyperlinked in the helpdesk ticketing app. We have implemented multiple solutions & band-aids to different symptoms of the problems such as: Using DNS Reservations for Macintosh PCs Using DNS Scavenging to remove old records Switching from a Cisco DHCP server to the Windows DHCP Server But no matter what we do, it seems impossible to maintain perfect records. Has anyone encountered this problem before? What is industry best practice? Comments & Suggestions are much appreciated, /P

  Read the article

• Connecting to my home router web interface from work

  - by Joe

  Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

  Read the article

• Virtual Machine Network Architecture, Isolating Public and Private Networks

  - by Mark

  I'm looking for some insight into best practices for network traffic isolation within a virtual environment, specifically under VMWARE ESXi. Currently I have (in testing) 1 hardware server running ESXi but i expect to expand this to multiple pieces of hardware. The current setup is as follows: 1 pfsense VM, this VM accepts all outside (WAN/internet) traffic and performs firewall/port forwarding/NAT functionality. I have multiple public IP addresses sent to the this VM that are used for access to individual servers (via per incoming IP port forwarding rules). This VM is attached to the private (virtual) network that all other VMs are on. It also manages a VPN link into the private network with some access restrictions. This isn't the perimeter firewall but rather the firewall for this virtual pool only. I have 3 VMs that communicate with each other, as well as have some public access requirements: 1 LAMP server running an eCommerce site, public internet accessible 1 accounting server, access via windows server 2008 RDS services for remote access by users 1 inventory/warehouse management server, VPN to client terminals in warehouses These servers constantly talk with each other for data synchronization. Currently all the servers are on the same subnet/virtual network and connected to the internet through the pfsense VM. The pfsense firewall uses port forwarding and NAT to allow outside access to the servers for services and for server access to the internet. My main question is this: Is there a security benefit to adding a second virtual network adapter to each server and controlling traffic such that all server to server communication is on one separate virtual network, while any access to the outside world is routed through the other network adapter, through the firewall, and on the the internet. This is the type of architecture i would use if these were all physical servers, but i'm unsure if the networks being virtual changes the way i should approach locking down this system. Thank you for any thoughts or direction to any appropriate literature.

  Read the article

• How do I secure Sql Server 2008 R2

  - by Mark Tait

  I have both a dedicated and a VPS (from Fasthosts) virtual server - the web sites/applications I run on these, access Sql Server stored on the same web server. Until now, I have logged onto Sql Server on both the deidicated and VPS server, from Sql Server Management Studio - until I noticed in my server application logs, multiple attempts to logon to Sql Server using the 'sa' username, but failed password. So someone/bot is trying hard (repeatedly every couple of hours, for approx 20 attempts during each instance) to log on... so obviously I have to lock down access to Sql Sever remotely. What I have done is gone into Configuration Manager, and in Sql Server Network Configuration - Protocols for Sql2008 and also in Sql Native Client 10.0 Configuration - Client Protocols - I have diabled Named Pipes, TCP/IP (and VIA by default). I have left Shared Memory enabled. I also disabled in Sql Server Services, the Sql Server Browser. Now the only way I can manage the databases on these servers, is by logging on to them via Remote Desktop. Can anyone confirm if this is the correct way of stopping anyone maliciously logging on to Sql Server? (I'm not a DBA or security expert - and there are hundreds of articles advising all different ways - but I was hoping for the experts here to confirm, or otherwise, if what I've done is correct) Thank you, Mark

  Read the article

• Registry remotley hacked win 7 need help tracking the perp

  - by user577229

  I was writing some .VBS code at thhe office that would allow certain file extensions to be downloaded without a warning dialog on a w7x32 system. The system I was writing this on is in a lab on a segmented subnet. All web access is via a proxy server. The only means of accessing my machine is via the internet or from within the labs MSFT AD domain. While writing and testing my code I found a message of sorts. Upon refresing the registry to verify my code changed a dword, instead the message HELLO was written and visible in regedit where the dword value wass called for. I took a screen shot and proceeded to edit my code. This same weird behavior occurred last time I was writing registry code except on another internal server. I understand that remote registry access exists for windows systems. I will block this immediately once I return to the office. What I want to know is, can I trace who made this connection? How would I do this? I suspect the cause of this is the cause of other "odd" behaviors I'm experiencing at work such as losing control of my input director master control for over an hour and unchanged code that all of a sudden fails for no logical region. These failures occur at funny times, whenver I'm about to give a demonstration of my test code. I know this sounds crazy however knowledge of the registry component makes this believable. Once the registry can be accessed, the entire system is compromised. Any help or sanity checking is appreciated.

  Read the article

• Network card/driver stops under heavy load

  - by Uwe Keim

  Since about approx. 2 month, I do have the following issue with my approx. 1 year old development machine (Windows 7, 64 bit): When doing network intensive operations, like e.g. executing some SQL script on a remote SQL server to select or update 1000 of records, the network card stops working. I.e. suddenly, No network connection is present anymore. No internet, no local connection, simply nothing. The only resolution so far I found is to disable my network card and then simply enable it back, like in the following screenshots: 1.) Click "Deactivate" 2.) Click "Activate" (German screenshots only, sorry) Now this is an acceptable solution to work around this issue, but I would love to have this fixed, since it suddenly stops me from working when I'm connected remotely via VPN/RDP on my machine (Win7 64bit). So my question is: Could you imagine a possible cause for this issue and give some hints how to hunt/resolve it? I could imagine that this is a driver issue, a hardware issue or even some kind of background software issue like a software firewall or a virus scanner.

  Read the article

• Solaris 10 invalid ARP requests from 0.0.0.0? Link up/down every hour or 2

  - by JWD

  The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). [mymacaddress]/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) It's being logged every hour. I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. There are some tunable SCTP parameters but it's not something I'm familiar with. Do I have to add changes to /etc/system? Looks like sctp_heartbeat_interval might be what I need to change? If it makes any difference, I have a few solaris zones running on this server, each with their own IP address on a virtual interface. eth0:0, eth0:1, etc. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else? Update: This was happening more frequently but now it seems to be happening roughly every hour or every two hours. It's not consistent. I tried setting setting the link speed and duplex to match the switch port and that seemed to make it stop happening for a few hours but then it started again.

  Read the article

• Set proper rights for sshfs mountpoint so it can be shared with samba

  - by CS01

  I have a domain hoster that provides access via SSH. My platforms are: Gentoo 2.6.36-r5 Windows (XP/Vista/7) I work on my Windows, I use Gentoo to do all the magic Windows can't do. Therefore I use sshfs to mount the remote public directory for my domain to /mnt/mydomain.com. Authentication is done via keys, so lazy me don't have to type in my password every now and then. Since I do my coding on Windows, and I don't want to upload/download the changed files all the time, I want to access this /mnt/mydomain.com via a samba share. So I shared /mnt in samba, all mounts except mydomain.com is listed on my Windows Explorer. My theories are: sshfs does not set the mountpoint uid/gid to something that samba expects samba does not know that it has to include the uid/gid that /mnt/mydomain.com has been set. All above is wrong, and I don't know. Here are configs and output from console, need anything else just let me know. Also no errors or warnings that I take notice of being relevant to this issue, but I might be wrong. gentoo ~ # ls -lah /mnt total 20K drwxr-xr-x 9 root root 4.0K Mar 26 16:15 . drwxr-xr-x 18 root root 4.0K Mar 26 2011 .. -rw-r--r-- 1 root root 0 Feb 1 16:12 .keep drwxr-xr-x 1 root root 0 Mar 18 12:09 buffer drwxr-s--x 1 68591 68591 4.0K Feb 16 15:43 mydomain.com drwx------ 2 root root 4.0K Feb 1 16:12 cdrom drwx------ 2 root root 4.0K Feb 1 16:12 floppy drwxr-xr-x 1 root root 0 Sep 1 2009 services drwxr-xr-x 1 root root 0 Feb 10 15:08 www /etc/samba/smb.conf [mnt] comment = Mount points writable = yes writeable = yes browseable = yes browsable = yes path = /mnt /etc/fstab sshfs#[email protected]:/home/to/pub/dir/ /mnt/mydomain.com/ fuse comment=sshfs,noauto,users,exec,uid=0,gid=0,allow_other,reconnect,follow_symlinks,transform_symlinks,idmap=none,SSHOPT=HostBasedAuthentication 0 0 For an easier read: [email protected] /home/to/pub/dir/ /mnt/mydomain.com/ options: comment=sshfs noauto users exec uid=0 gid=0 allow_other reconnect follow_symlinks transform_symlinks idmap=none SSHOPT=HostBasedAuthentication Help!

  Read the article

• PTR record not valid for all domains

  - by charnley

  We have an issue sending emails to certain domains, namely Time Warner and Cox. Last week, we decommissioned our Exchange 2003 server and now our Exchange 2010 server is doing all of the transport for our domain. We run our own authoritative name servers, so we are in charge of the DNS and have modified our PTR record to reflect the new server. All mailflow is working except for these 2 domains. When I telnet on port 25 to the mail servers for Cox and Time Warner I am receiving errors. For Cox the error is: 554... rejected - no rDNS And when I telnet to port 25 to the Time Warner mail server we get this: 554 5.7.1 - Connection refused. IP name lookup failed for x.x.x.x I have run through the outbound SMTP test on Microsoft Remote Connectivity Analyzer and get 100% completely successful results. MXToolbox comes up with all successful tests on SMTP as well, showing correct reverse banner check, and no blacklisting. DNSQueries.com shows a valid reverse DNS entry as well for us. Outbound emails to these 2 domains continue to sit in the queue. Any ideas or advice would be greatly appreciated. Thanks!

  Read the article

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  Hello - I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified with SpeakEasy and Speedtest.net) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• SMTP message rate control on Ubuntu 8.04, preferably with postfix

  - by TimDaMan

  Maybe I am chasing a bug but I am trying to set up a smtp proxy of sorts. I have a postfix server which receives all the email for a collection of servers/clients. It them uses a smarthost (relayhost=...) to forward it's mail to our corporate MTA. I would like to limit the number of messages an individual server can relay to prevent swamping the corporate MTA. Postfix has a program called "anvil" that is capable of tracking stats about mail to be used for such things but it doesn't seem to be executed. I ran "inotifywait -m /usr/lib/postfix/anvil" while I started postfix and sent a number of messages through it from a remote server. inotifywait indicated anvil was never run. Anyone gotten postfix/anvil rate controls to work? main.cf smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no append_dot_mydomain = no readme_directory = no myhostname = site-server-q9 alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost relayhost = Out outgoing mail relay mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 10.0.0.0/8 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = 10.X.X.X smtpd_client_message_rate_limit = 1 anvil_rate_time_unit = 1h master.cf extract anvil unix - - - - 1 anvil smtp inet n - - - - smtpd

  Read the article

< Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >