Search Results

Search found 12666 results on 507 pages for 'knowledge base'.

Page 444/507 | < Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >

• ubuntu 10.04: wlan0 No such device

  - by AodhanOL

  I am using a Dell xps l702x and I am using ubuntu 10.04 because I need to use f77 (don't ask) and I wasn't able to get it working on later versions of ubuntu. I cannot use the wifi at all. I have tried to fix it and have had limited success (changed the output from rfkill list all from Hard blocked: yes, to hard blocked: no). Here is the output from rfkill list all aodhan@aodhan-laptop:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: dell-bluetooth: Bluetooth Soft blocked: no Hard blocked: no Here is the output from iwconfig: aodhan@aodhan-laptop:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. pan0 no wireless extensions. And here is the output from ifconfig -a: aodhan@aodhan-laptop:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 5c:f9:dd:3d:f2:f7 inet addr:192.168.1.17 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::5ef9:ddff:fe3d:f2f7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3417 errors:0 dropped:0 overruns:0 frame:0 TX packets:2894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3317567 (3.3 MB) TX bytes:505049 (505.0 KB) Interrupt:30 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 7e:7e:e8:39:70:af BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And finally, the output from lspci: 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4b (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation Device 1246 (rev a1) 03:00.0 Network controller: Intel Corporation Device 008a (rev 34) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Please help me! Thank you in advance. Edit: Further info - this is a dual install with a windows 7 system as the other option. However, I can't access that until tomorrow (I won't have access to the windows 7 disc until then, and grub isn't letting me load it). Therefore, I can't be sure whether it still works on that or not. It used to, though.

  Read the article

• Slide 2d Vector to destination over a period of time

  - by SchautDollar

  I am making a library of GUI controls for games I make with XNA. I am currently developing the library as I make a game so I can test the features and find errors/bugs and hopefully smash them right away. My current issue is on a slide feature I want to implement for my base class that all controls inherit. My goal is to get the control to slide to a specified point over a specified amount of time. Here is the #region containing the code #region Slide private bool sliding; private Vector2 endPoint; private float slideTimeLeft; private float speed; private bool wasEnabled; private Vector2 slideDirection; private float slideDistance; public void Slide(Vector2 startPoint, Vector2 endPoint, float slideTime) { this.location = startPoint; Slide(endPoint,slideTime); } public void Slide(Vector2 endPoint, float slideTime) { this.wasEnabled = this.enabled; this.enabled = false; this.sliding = true; Vector2 tempLength = endPoint - this.location; this.slideDistance = tempLength.Length(); //Was this.slideDistance = (float)Math.Sqrt(tempLength.LengthSquared()); this.speed = slideTime / this.slideDistance; this.endPoint = endPoint; this.slideTimeLeft = slideTime; } private void UpdateSlide(GameTime gameTime) { if (this.sliding) { this.slideTimeLeft -= gameTime.ElapsedGameTime.Milliseconds; if (this.slideTimeLeft >= 0 ) { if ((this.endPoint-this.location).Length() != 0){//Was if (this.endPoint.LengthSquared() > 0 || this.location.LengthSquared() > 0) { this.slideDirection = Vector2.Normalize(this.endPoint - this.location); } this.location += this.slideDirection * speed * gameTime.ElapsedGameTime.Milliseconds;//This is where I believe the issue is, but I'm not sure. It seems right to me... (Even though it doesn't work) } else { this.enabled = this.wasEnabled; this.location = this.endPoint;//After time, the controls position will get set to be the endpoint. this.sliding = false; } } } #endregion this.location is the location of the control elsewhere defined in the class. I have looked at this blog as a huge reference and have googled around quite and have looked on many forums but can't find anything that shows how to implement it. Please and Thanks for your time! EDIT: I have switched this line "this.location += this.slideDirection * speed * gameTime.ElapsedGameTime.Milliseconds;" several times to see what it does. My issue is getting the control to smoothly move to the end location. It moves after the time has expired, but It doesn't move other then that except flash in my face. EDIT2: I have used the first slide method with 3 parameters and it works except it doesn't do it in a period of time and once it gets to its destination, it starts moving randomly towards the previous location and the end location.

  Read the article

• Errors when switching to specific static IP

  - by michaelc

  I had a Fedora box running using my static IP 69.169.136.6, etc, all configured according to what the ISP required. Just recently the hard drive failed (and I should have been keeping better backups) - while it is being recovered I would like to put up a webpage on my Archlinux PC explaining the problem - I presently do not have sufficient access to change the DNS record assigned to the domain. When I change my ip address while my system is running to 69.169.136.6, ifconfig reports the new ip address, but http://whatismyip.com/ does not. When I change it and reboot, I can't ping - the message I recieve is "connect: Network is unreachable" (when given one of google.com 's IP addresses - hostnames give me ping: unknown host xxx). Until I have access to the DNS system, what can I do to make this work? Edit: With new IP address, same problem, IP is now 69.169.136.29. Some commands might be useful: #ping 69.169.136.1 PING 69.169.136.1 (69.169.136.1) 56(84) bytes of data. 64 bytes from 69.169.136.1: icmp_seq=1 ttl=64 time=0.377 ms #ping 69.169.190.211 connect: Network is unreachable #ping 208.72.160.67 connect: Network is unreachable #ifconfig eth0 Link encap:Ethernet HWaddr 00:E0:4D:97:23:9B inet addr:69.169.136.29 Bcast:69.169.137.255 Mask:255.255.254.0 inet6 addr: fe80::2e0:4dff:fe97:239b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:132091 errors:0 dropped:0 overruns:0 frame:0 TX packets:17 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9635179 (9.1 Mb) TX bytes:1322 (1.2 Kb) Interrupt:29 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:48 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2480 (2.4 Kb) TX bytes:2480 (2.4 Kb) #ip route 69.169.136.0/23 dev eth0 proto kernel scope link src 69.169.136.29 #cat /etc/resolv.conf # Generated by dhcpcd #nameserver 208.67.222.222 #nameserver 208.67.220.220 nameserver 69.169.190.211 nameserver 208.72.160.67 # /etc/resolv.conf.tail can replace this line Update: have new static IP addresses, verified to work in Windows... Relevant portions of /etc/rc.conf below: #Static IP example #eth0="eth0 69.169.136.6 netmask 255.255.254.0 broadcast 69.169.136.1" #eth0="eth0 69.169.136.29 netmask 255.255.254.0 broadcast 69.169.137.255" eth0="eth0 69.169.136.32 netmask 255.255.254.0 broadcast 69.169.137.255" #eth0="dhcp" INTERFACES=(eth0) # Routes to start at boot-up (in this order) # Declare each route then list in ROUTES # - prefix an entry in ROUTES with a ! to disable it # #gateway="default gw 192.168.0.1" gateway="default gw 69.169.136.1" #gateway="69.169.136.1" ROUTES=(!gateway) #ROUTES=()

  Read the article

• CentOS 5.5 : Postfix, Dovecot & MySQL

  - by GruffTech

  I'm hoping someone has seen this issue before because I'm at quite a loss. We're building a new outbound smtp server for our clients that features anti-spam scanning and virus scanning for outbound emails, something we had not previously done. So with CentOS 5.5 x64, Installed and patched completely. Postfix & Dovecot both installed via base repo. [grufftech@outgoing postfix]# rpm -qa | grep postfix postfix-2.3.3-2.1.el5_2 [grufftech@outgoing postfix]# rpm -qa | grep dovecot dovecot-1.0.7-7.el5 [grufftech@outgoing ~]# dovecot --build-options Build options: ioloop=poll notify=inotify ipv6 openssl SQL drivers: mysql postgresql Passdb: checkpassword ldap pam passwd passwd-file shadow sql Userdb: checkpassword ldap passwd prefetch passwd-file sql static /etc/dovecot.conf auth default { mechanisms = plain login digest-md5 cram-md5 passdb sql { args = /etc/dovecot-mysql.conf } userdb sql { args = /etc/dovecot-mysql.conf } userdb prefetch { } user = nobody socket listen { master { path = /var/run/dovecot/auth-master mode = 0660 user = postfix group = postfix } client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } } } All the server is doing is auth for postfix, so no reason to have imap / pop / dict. /etc/dovecot-mysql.conf driver = mysql connect = host=10.0.32.159 dbname=mail user=****** password=******** default_pass_scheme = plain user_query = select 1 password_query = select password from users where username = '%n' and domain = '%d' So drop in my configuration, (which is working on another server identical to this one.) [grufftech@outgoing ~]# /etc/init.d/dovecot start Starting Dovecot Imap: [ OK ] Sweet. Booted up nicely, thats good.... (incoming problem in 3....2....1....) May 21 08:09:01 outgoing dovecot: Dovecot v1.0.7 starting up May 21 08:09:02 outgoing dovecot: auth-worker(default): mysql: Connect failed to 10.0.32.159 (mail): Can't connect to MySQL server on '10.0.32.159' (13) - waiting for 1 seconds before retry well what the crap. went and checked permissions on my MySQL database, and its fine. [grufftech@outgoing ~]# mysql vpopmail -h 10.0.32.159 -u ****** -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 127828558 Server version: 4.1.22 Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql>\q So! My server can talk to my database server. but dovecot, for whatever reason, isn't able to. I've fiddled with it for the last six hours, grabbed slightly-older copies of the RPM (ones that matched our production server exactly) to test those, copied configs, searched google, searched server fault, chatted in IRC, banged my head against the table, I've done it all. Surely I'm doing something wrong or forgetting something, can anyone tell me what the elephant in the room is? This stuff is supposed to work.

  Read the article

• Why won't ruby recognize Haml under ubuntu64 while using jekyll static blog generator?

  - by oldmanjoyce

  I have been trying, quite unsuccessfully, to run henrik's fork of the jekyll static blog generator on Ubuntu 64-bit. I just can't seem to figure this out and I've tried a bunch of different things. Originally I posted this over at stackoverflow, but this is probably the better spot for it. The base stats of my machine: Ubuntu 9.04, 64 bit, ruby 1.8.7 (2008-08-11 patchlevel 72) [x86_64-linux], rubygems 1.3.1. When I attempt to build the site, this is what happens: $ jekyll --pygments Configuration from ./_config.yml Using Sass for CSS generation You must have the haml gem installed first Using rdiscount for Markdown Building site: . - ./_site /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/core_ext.rb:27:in `method_missing': undefined method 'header' for #, page=# ..... cut ..... (NoMethodError) from (haml):9:in `render' from /home/chris/.gem/gems/haml-2.2.3/lib/haml/engine.rb:167:in 'render' from /home/chris/.gem/gems/haml-2.2.3/lib/haml/engine.rb:167:in 'instance_eval' from /home/chris/.gem/gems/haml-2.2.3/lib/haml/engine.rb:167:in 'render' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/convertible.rb:72:in 'render_haml_in_context' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/convertible.rb:105:in 'do_layout' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/post.rb:226:in 'render' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/site.rb:172:in 'read_posts' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/site.rb:171:in 'each' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/site.rb:171:in 'read_posts' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/site.rb:210:in 'transform_pages' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/../lib/jekyll/site.rb:126:in 'process' from /home/chris/.gem/gems/henrik-jekyll-0.5.2/bin/jekyll:135 from /home/chris/.gem/bin/jekyll:19:in `load' from /home/chris/.gem/bin/jekyll:19 I added spaces to the left of the ClosedStruct to enable better visibility - sorry that my inline html/formatting isn't perfect. I also cut out some middle text that is just data. $ gem list *** LOCAL GEMS *** actionmailer (2.3.4) actionpack (2.3.4) activerecord (2.3.4) activeresource (2.3.4) activesupport (2.3.4) classifier (1.3.1) directory_watcher (1.2.0) haml (2.2.3) haml-edge (2.3.27) henrik-jekyll (0.5.2) liquid (2.0.0) maruku (0.6.0) open4 (0.9.6) rack (1.0.0) rails (2.3.4) rake (0.8.7) rdiscount (1.3.5) RedCloth (4.2.2) stemmer (1.0.1) syntax (1.0.0) Some showing for path verification: $ echo $PATH /home/chris/.gem/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games $ which haml /home/chris/.gem/bin/haml $ which jekyll /home/chris/.gem/bin/jekyll

  Read the article

• Partitioning recommendations for a Proxmox VM Server (OpenVZ)

  - by luison

  We are new to virtualization and we are planning to turn our online server into a virualized one, mainly for maintenance, backup and recovery improvements. Initially we would only have one real virtual system with load plus 1-3 copys for testing and recovering and maybe a small centralized syslog virtual machine. We would like, if possible the host machine to include an iptables plus rsync to back up to other machines and some other global security systems. Due to this and the offerings of our hosting supplier we are mainly considering Proxmox for its simplicity (we like the idea of its web admin panel) and as I also understand that the container approach of OpenVMZ systems may fit well resource wise with our setup. The base system comes with debian so we can personalise it to our requirements. Proxmox installations default installs an LVM partition for the VMs. Our doubts are with the fact of what would be the best partition structure for this considering that: we would like to have a mirror of the root partition we could boot from if required (our provider supports booting the system from another partition via control panel) we ideally would like to have a partition that could be shared among the VM systems. We still don't know if this is possible directly with OpenVMZ containers, otherwise we are considering doing this by sharing it via NFS on the host machine. we want to use the backup system available on the proxmox host administrator to programme VMs backups and then rsync it to another machine. With this based on a Linux Raid of aprox (750Gb) we are considering something like: ext3_1/ - (20Gb) ext3_2/bak_root - (20Gb) mostly unmounted, root partition sync LVM_1 /var/lib/vz - (390Gb) partition for virtual images LVM_2 /shared_data - (30Gb) LVM_3 /backups - (300Gb) where all backups would be allocated Our initial tests with Proxmox seem to have issues with snapshots backups like this, perhaps caused by the fact that they can not be done to another LVM partition (error: command 'lvcreate --size 1024M --snapshot --name vzsnap-ns204084.XXX.net-0 /dev/pve/LV' failed with exit code 5) in which case we might have to use a standart ext3 partition (but unsure if we can do this with the 4 primary partition limitations). Does this makes more or less sense? Would it be mad to for example write VMs /var/logs to a NFS mounted partition (on the host system)? Are their any other easier ways to mount host system partitions (or folders) to the VMs?

  Read the article

• TF30004: The New Team Project Wizard encountered an unexpected error while initializing the Microsof

  - by Frozzare

  Hello, i get this error when i trying to create a new project in team project. The server is right, i check all ports. I don't now what i should do now, can't find any good information 2009-09-19 01:45:41Z | Module: Internal | Team Foundation Server proxy retrieved | Completion time: 0.338 seconds 2009-09-19 01:45:41Z | Module: Internal | The template information for Team Foundation Server "TFSServer01" was retrieved from the Team Foundation Server. | Completion time: 0.099 seconds 2009-09-19 01:45:41Z | Module: Wizard | Retrieved IAuthorizationService proxy | Completion time: 0.404 seconds 2009-09-19 01:45:41Z | Module: Wizard | TF30227: Project creation permissions retrieved | Completion time: 0.015 seconds 2009-09-19 01:45:44Z | Module: Engine | Thread: 5 | New project will be created with the "MSF for Agile Software Development - v4.2" methodology 2009-09-19 01:45:44Z | Module: Engine | Retrieved IAuthorizationService proxy | Completion time: 0 seconds 2009-09-19 01:45:44Z | Module: Engine | TF30227: Project creation permissions retrieved | Completion time: 0.01 seconds 2009-09-19 01:45:45Z | Module: Engine | Wrote compressed process template file | Completion time: 0.001 seconds 2009-09-19 01:45:46Z | Module: Engine | Extracted process template file | Completion time: 1.428 seconds 2009-09-19 01:45:46Z | Module: Engine | Thread: 5 | Starting Project Creation for project "TestProject" in domain "TFSServer01" 2009-09-19 01:45:46Z | Module: Engine | The user identity information was retrieved from the Group Security Service | Completion time: 0.045 seconds 2009-09-19 01:45:46Z | Module: Initializer | Thread: 5 | The New Team Project Wizard is starting to initialize the plug-ins. 2009-09-19 01:45:46Z | Module: CssStructureUploader | Thread: 5 | Entering Initialize in CssStructureUploader 2009-09-19 01:45:46Z | Module: CssStructureUploader | Thread: 5 | Initialize for CssStructureUploader complete 2009-09-19 01:45:46Z | Module: Initializer | Thread: 5 | The New Team Project Wizard successfully Initialized the plug-in Microsoft.ProjectCreationWizard.Classification. 2009-09-19 01:45:46Z | Module: Rosetta | Thread: 5 | Entering Initialize in RosettaReportUploader 2009-09-19 01:45:48Z | Module: Rosetta | Thread: 5 | Exiting Initialize for RosettaReportUploader 2009-09-19 01:45:48Z | Module: Initializer | Thread: 5 | The New Team Project Wizard successfully Initialized the plug-in Microsoft.ProjectCreationWizard.Reporting. 2009-09-19 01:45:48Z | Module: WSS | Thread: 5 | Entering Initialize in WssSiteCreator 2009-09-19 01:45:48Z | Module: WSS | Thread: 5 | Site information: Title = "TestProject" Description = "This team project was created based on the 'MSF for Agile Software Development - v4.2' process template." 2009-09-19 01:45:48Z | Module: WSS | Thread: 5 | Base site url: http://TFSServer01:14143/webbplatser 2009-09-19 01:45:48Z | Module: WSS | Thread: 5 | Admin site url: http://TFSServer01:16183/_vti_adm/admin.asmx ---begin Exception entry--- Time: 2009-09-19 01:46:27 Z Module: Initialize Event Description: TF30207: Initialization for plugin "Microsoft.ProjectCreationWizard.Portal 'failed Exception Type: Microsoft.TeamFoundation.Client.PcwException Exception Message: The client discovered that content-type of request is text / html; charset = utf-8, but the text / xml expected. The request failed with error message: -- Unable to connect to the configuration database. --. Stack Trace: vid Microsoft.VisualStudio.TeamFoundation.WssSiteCreator.CheckPermissions(ProjectCreationContext ctxt) vid Microsoft.VisualStudio.TeamFoundation.WssSiteCreator.Initialize(ProjectCreationContext context) vid Microsoft.VisualStudio.TeamFoundation.EngineStarter.InitializePlugins(MsfTemplate template, PcwPluginCollection pluginCollection) -- Inner Exception -- Exception Type: System.InvalidOperationException Exception Message: The client discovered that content-type of request is text / html; charset = utf-8, but the text / xml expected. The request failed with error message: -- Unable to connect to the configuration database. --. Stack Trace: vid System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) vid System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) vid Microsoft.TeamFoundation.Proxy.Portal.Admin.GetLanguages() vid Microsoft.VisualStudio.TeamFoundation.WssSiteCreator.CheckPermissions(ProjectCreationContext ctxt) -- end Inner Exception -- --- end Exception entry --- Thanks for you help

  Read the article

• dbus dependency with yum

  - by Hengjie

  Whenever, I try and run yum update I get the following error: [root@server ~]# yum update Loaded plugins: dellsysid, fastestmirror Loading mirror speeds from cached hostfile * base: mirror01.idc.hinet.net * extras: mirror01.idc.hinet.net * rpmforge: fr2.rpmfind.net * updates: mirror01.idc.hinet.net Excluding Packages in global exclude list Finished Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package NetworkManager.x86_64 1:0.7.0-13.el5 set to be updated ---> Package NetworkManager-glib.x86_64 1:0.7.0-13.el5 set to be updated ---> Package SysVinit.x86_64 0:2.86-17.el5 set to be updated ---> Package acl.x86_64 0:2.2.39-8.el5 set to be updated ---> Package acpid.x86_64 0:1.0.4-12.el5 set to be updated ---> Package apr.x86_64 0:1.2.7-11.el5_6.5 set to be updated ---> Package aspell.x86_64 12:0.60.3-12 set to be updated ---> Package audit.x86_64 0:1.8-2.el5 set to be updated ---> Package audit-libs.x86_64 0:1.8-2.el5 set to be updated ---> Package audit-libs-python.x86_64 0:1.8-2.el5 set to be updated ---> Package authconfig.x86_64 0:5.3.21-7.el5 set to be updated ---> Package autofs.x86_64 1:5.0.1-0.rc2.163.el5 set to be updated ---> Package bash.x86_64 0:3.2-32.el5 set to be updated ---> Package bind.x86_64 30:9.3.6-20.P1.el5 set to be updated ---> Package bind-libs.x86_64 30:9.3.6-20.P1.el5 set to be updated ---> Package bind-utils.x86_64 30:9.3.6-20.P1.el5 set to be updated ---> Package binutils.x86_64 0:2.17.50.0.6-20.el5 set to be updated ---> Package centos-release.x86_64 10:5-8.el5.centos set to be updated ---> Package centos-release-notes.x86_64 0:5.8-0 set to be updated ---> Package coreutils.x86_64 0:5.97-34.el5_8.1 set to be updated ---> Package cpp.x86_64 0:4.1.2-52.el5 set to be updated ---> Package cpuspeed.x86_64 1:1.2.1-10.el5 set to be updated ---> Package crash.x86_64 0:5.1.8-1.el5.centos set to be updated ---> Package cryptsetup-luks.x86_64 0:1.0.3-8.el5 set to be updated ---> Package cups.x86_64 1:1.3.7-30.el5 set to be updated ---> Package cups-libs.x86_64 1:1.3.7-30.el5 set to be updated ---> Package curl.x86_64 0:7.15.5-15.el5 set to be updated --> Processing Dependency: dbus = 1.1.2-15.el5_6 for package: dbus-libs ---> Package dbus.x86_64 0:1.1.2-16.el5_7 set to be updated ---> Package dbus-libs.x86_64 0:1.1.2-16.el5_7 set to be updated ---> Package device-mapper.x86_64 0:1.02.67-2.el5 set to be updated ---> Package device-mapper-event.x86_64 0:1.02.67-2.el5 set to be updated ---> Package device-mapper-multipath.x86_64 0:0.4.7-48.el5_8.1 set to be updated ---> Package dhclient.x86_64 12:3.0.5-31.el5 set to be updated ---> Package dmidecode.x86_64 1:2.11-1.el5 set to be updated ---> Package dmraid.x86_64 0:1.0.0.rc13-65.el5 set to be updated ---> Package dmraid-events.x86_64 0:1.0.0.rc13-65.el5 set to be updated ---> Package dump.x86_64 0:0.4b41-6.el5 set to be updated ---> Package e2fsprogs.x86_64 0:1.39-33.el5 set to be updated ---> Package e2fsprogs-devel.x86_64 0:1.39-33.el5 set to be updated ---> Package e2fsprogs-libs.x86_64 0:1.39-33.el5 set to be updated ---> Package ecryptfs-utils.x86_64 0:75-8.el5 set to be updated ---> Package file.x86_64 0:4.17-21 set to be updated ---> Package finger.x86_64 0:0.17-33 set to be updated ---> Package firstboot-tui.x86_64 0:1.4.27.9-1.el5.centos set to be updated ---> Package freetype.x86_64 0:2.2.1-28.el5_7.2 set to be updated ---> Package freetype-devel.x86_64 0:2.2.1-28.el5_7.2 set to be updated ---> Package ftp.x86_64 0:0.17-37.el5 set to be updated ---> Package gamin.x86_64 0:0.1.7-10.el5 set to be updated ---> Package gamin-python.x86_64 0:0.1.7-10.el5 set to be updated ---> Package gawk.x86_64 0:3.1.5-15.el5 set to be updated ---> Package gcc.x86_64 0:4.1.2-52.el5 set to be updated ---> Package gcc-c++.x86_64 0:4.1.2-52.el5 set to be updated ---> Package glibc.i686 0:2.5-81.el5_8.1 set to be updated ---> Package glibc.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package glibc-common.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package glibc-devel.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package glibc-headers.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package gnutls.x86_64 0:1.4.1-7.el5_8.2 set to be updated ---> Package groff.x86_64 0:1.18.1.1-13.el5 set to be updated ---> Package gtk2.x86_64 0:2.10.4-21.el5_7.7 set to be updated ---> Package gzip.x86_64 0:1.3.5-13.el5.centos set to be updated ---> Package hmaccalc.x86_64 0:0.9.6-4.el5 set to be updated ---> Package htop.x86_64 0:1.0.1-2.el5.rf set to be updated ---> Package hwdata.noarch 0:0.213.26-1.el5 set to be updated ---> Package ifd-egate.x86_64 0:0.05-17.el5 set to be updated ---> Package initscripts.x86_64 0:8.45.42-1.el5.centos set to be updated ---> Package iproute.x86_64 0:2.6.18-13.el5 set to be updated ---> Package iptables.x86_64 0:1.3.5-9.1.el5 set to be updated ---> Package iptables-ipv6.x86_64 0:1.3.5-9.1.el5 set to be updated ---> Package iscsi-initiator-utils.x86_64 0:6.2.0.872-13.el5 set to be updated ---> Package kernel.x86_64 0:2.6.18-308.1.1.el5 set to be installed ---> Package kernel-headers.x86_64 0:2.6.18-308.1.1.el5 set to be updated ---> Package kpartx.x86_64 0:0.4.7-48.el5_8.1 set to be updated ---> Package krb5-devel.x86_64 0:1.6.1-70.el5 set to be updated ---> Package krb5-libs.x86_64 0:1.6.1-70.el5 set to be updated ---> Package krb5-workstation.x86_64 0:1.6.1-70.el5 set to be updated ---> Package ksh.x86_64 0:20100621-5.el5_8.1 set to be updated ---> Package kudzu.x86_64 0:1.2.57.1.26-3.el5.centos set to be updated ---> Package less.x86_64 0:436-9.el5 set to be updated ---> Package lftp.x86_64 0:3.7.11-7.el5 set to be updated ---> Package libX11.x86_64 0:1.0.3-11.el5_7.1 set to be updated ---> Package libX11-devel.x86_64 0:1.0.3-11.el5_7.1 set to be updated ---> Package libXcursor.x86_64 0:1.1.7-1.2 set to be updated ---> Package libacl.x86_64 0:2.2.39-8.el5 set to be updated ---> Package libgcc.x86_64 0:4.1.2-52.el5 set to be updated ---> Package libgomp.x86_64 0:4.4.6-3.el5.1 set to be updated ---> Package libpng.x86_64 2:1.2.10-16.el5_8 set to be updated ---> Package libpng-devel.x86_64 2:1.2.10-16.el5_8 set to be updated ---> Package libsmbios.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package libstdc++.x86_64 0:4.1.2-52.el5 set to be updated ---> Package libstdc++-devel.x86_64 0:4.1.2-52.el5 set to be updated ---> Package libsysfs.x86_64 0:2.1.0-1.el5 set to be updated ---> Package libusb.x86_64 0:0.1.12-6.el5 set to be updated ---> Package libvolume_id.x86_64 0:095-14.27.el5_7.1 set to be updated ---> Package libxml2.x86_64 0:2.6.26-2.1.15.el5_8.2 set to be updated ---> Package libxml2-python.x86_64 0:2.6.26-2.1.15.el5_8.2 set to be updated ---> Package logrotate.x86_64 0:3.7.4-12 set to be updated ---> Package lsof.x86_64 0:4.78-6 set to be updated ---> Package lvm2.x86_64 0:2.02.88-7.el5 set to be updated ---> Package m2crypto.x86_64 0:0.16-8.el5 set to be updated ---> Package man.x86_64 0:1.6d-2.el5 set to be updated ---> Package man-pages.noarch 0:2.39-20.el5 set to be updated ---> Package mcelog.x86_64 1:0.9pre-1.32.el5 set to be updated ---> Package mesa-libGL.x86_64 0:6.5.1-7.10.el5 set to be updated ---> Package mesa-libGL-devel.x86_64 0:6.5.1-7.10.el5 set to be updated ---> Package microcode_ctl.x86_64 2:1.17-1.56.el5 set to be updated ---> Package mkinitrd.x86_64 0:5.1.19.6-75.el5 set to be updated ---> Package mktemp.x86_64 3:1.5-24.el5 set to be updated --> Processing Dependency: nash = 5.1.19.6-68.el5_6.1 for package: mkinitrd ---> Package nash.x86_64 0:5.1.19.6-75.el5 set to be updated ---> Package net-snmp.x86_64 1:5.3.2.2-17.el5 set to be updated ---> Package net-snmp-devel.x86_64 1:5.3.2.2-17.el5 set to be updated ---> Package net-snmp-libs.x86_64 1:5.3.2.2-17.el5 set to be updated ---> Package net-snmp-utils.x86_64 1:5.3.2.2-17.el5 set to be updated ---> Package net-tools.x86_64 0:1.60-82.el5 set to be updated ---> Package nfs-utils.x86_64 1:1.0.9-60.el5 set to be updated ---> Package nfs-utils-lib.x86_64 0:1.0.8-7.9.el5 set to be updated ---> Package nscd.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package nspr.x86_64 0:4.8.9-1.el5_8 set to be updated ---> Package nspr-devel.x86_64 0:4.8.9-1.el5_8 set to be updated ---> Package nss.x86_64 0:3.13.1-5.el5_8 set to be updated ---> Package nss-devel.x86_64 0:3.13.1-5.el5_8 set to be updated ---> Package nss-tools.x86_64 0:3.13.1-5.el5_8 set to be updated ---> Package nss_ldap.x86_64 0:253-49.el5 set to be updated ---> Package ntp.x86_64 0:4.2.2p1-15.el5.centos.1 set to be updated ---> Package numactl.x86_64 0:0.9.8-12.el5_6 set to be updated ---> Package oddjob.x86_64 0:0.27-12.el5 set to be updated ---> Package oddjob-libs.x86_64 0:0.27-12.el5 set to be updated ---> Package openldap.x86_64 0:2.3.43-25.el5 set to be updated ---> Package openssh.x86_64 0:4.3p2-82.el5 set to be updated ---> Package openssh-clients.x86_64 0:4.3p2-82.el5 set to be updated ---> Package openssh-server.x86_64 0:4.3p2-82.el5 set to be updated ---> Package openssl.i686 0:0.9.8e-22.el5_8.1 set to be updated ---> Package openssl.x86_64 0:0.9.8e-22.el5_8.1 set to be updated ---> Package openssl-devel.x86_64 0:0.9.8e-22.el5_8.1 set to be updated ---> Package pam_krb5.x86_64 0:2.2.14-22.el5 set to be updated ---> Package pam_pkcs11.x86_64 0:0.5.3-26.el5 set to be updated ---> Package pango.x86_64 0:1.14.9-8.el5.centos.3 set to be updated ---> Package parted.x86_64 0:1.8.1-29.el5 set to be updated ---> Package pciutils.x86_64 0:3.1.7-5.el5 set to be updated ---> Package perl.x86_64 4:5.8.8-38.el5 set to be updated ---> Package perl-Compress-Raw-Bzip2.x86_64 0:2.037-1.el5.rf set to be updated ---> Package perl-Compress-Raw-Zlib.x86_64 0:2.037-1.el5.rf set to be updated ---> Package perl-rrdtool.x86_64 0:1.4.7-1.el5.rf set to be updated ---> Package poppler.x86_64 0:0.5.4-19.el5 set to be updated ---> Package poppler-utils.x86_64 0:0.5.4-19.el5 set to be updated ---> Package popt.x86_64 0:1.10.2.3-28.el5_8 set to be updated ---> Package postgresql-libs.x86_64 0:8.1.23-1.el5_7.3 set to be updated ---> Package procps.x86_64 0:3.2.7-18.el5 set to be updated ---> Package proftpd.x86_64 0:1.3.4a-1.el5.rf set to be updated --> Processing Dependency: perl(Mail::Sendmail) for package: proftpd ---> Package python.x86_64 0:2.4.3-46.el5 set to be updated ---> Package python-ctypes.x86_64 0:1.0.2-3.el5 set to be updated ---> Package python-libs.x86_64 0:2.4.3-46.el5 set to be updated ---> Package python-smbios.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package rhpl.x86_64 0:0.194.1-2 set to be updated ---> Package rmt.x86_64 0:0.4b41-6.el5 set to be updated ---> Package rng-utils.x86_64 1:2.0-5.el5 set to be updated ---> Package rpm.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rpm-build.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rpm-devel.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rpm-libs.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rpm-python.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rrdtool.x86_64 0:1.4.7-1.el5.rf set to be updated ---> Package rsh.x86_64 0:0.17-40.el5_7.1 set to be updated ---> Package rsync.x86_64 0:3.0.6-4.el5_7.1 set to be updated ---> Package ruby.x86_64 0:1.8.5-24.el5 set to be updated ---> Package ruby-libs.x86_64 0:1.8.5-24.el5 set to be updated ---> Package sblim-sfcb.x86_64 0:1.3.11-49.el5 set to be updated ---> Package sblim-sfcc.x86_64 0:2.2.2-49.el5 set to be updated ---> Package selinux-policy.noarch 0:2.4.6-327.el5 set to be updated ---> Package selinux-policy-targeted.noarch 0:2.4.6-327.el5 set to be updated ---> Package setup.noarch 0:2.5.58-9.el5 set to be updated ---> Package shadow-utils.x86_64 2:4.0.17-20.el5 set to be updated ---> Package smartmontools.x86_64 1:5.38-3.el5 set to be updated ---> Package smbios-utils-bin.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package smbios-utils-python.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package sos.noarch 0:1.7-9.62.el5 set to be updated ---> Package srvadmin-omilcore.x86_64 0:6.5.0-1.452.1.el5 set to be updated ---> Package strace.x86_64 0:4.5.18-11.el5_8 set to be updated ---> Package subversion.x86_64 0:1.6.11-7.el5_6.4 set to be updated ---> Package sudo.x86_64 0:1.7.2p1-13.el5 set to be updated ---> Package sysfsutils.x86_64 0:2.1.0-1.el5 set to be updated ---> Package syslinux.x86_64 0:3.11-7 set to be updated ---> Package system-config-network-tui.noarch 0:1.3.99.21-1.el5 set to be updated ---> Package talk.x86_64 0:0.17-31.el5 set to be updated ---> Package tar.x86_64 2:1.15.1-31.el5 set to be updated ---> Package traceroute.x86_64 3:2.0.1-6.el5 set to be updated ---> Package tzdata.x86_64 0:2012b-3.el5 set to be updated ---> Package udev.x86_64 0:095-14.27.el5_7.1 set to be updated ---> Package util-linux.x86_64 0:2.13-0.59.el5 set to be updated ---> Package vixie-cron.x86_64 4:4.1-81.el5 set to be updated ---> Package wget.x86_64 0:1.11.4-3.el5_8.1 set to be updated ---> Package xinetd.x86_64 2:2.3.14-16.el5 set to be updated ---> Package yp-tools.x86_64 0:2.9-2.el5 set to be updated ---> Package ypbind.x86_64 3:1.19-12.el5_6.1 set to be updated ---> Package yum.noarch 0:3.2.22-39.el5.centos set to be updated ---> Package yum-dellsysid.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package yum-fastestmirror.noarch 0:1.1.16-21.el5.centos set to be updated ---> Package zlib.x86_64 0:1.2.3-4.el5 set to be updated ---> Package zlib-devel.x86_64 0:1.2.3-4.el5 set to be updated --> Running transaction check --> Processing Dependency: dbus = 1.1.2-15.el5_6 for package: dbus-libs --> Processing Dependency: nash = 5.1.19.6-68.el5_6.1 for package: mkinitrd ---> Package perl-Mail-Sendmail.noarch 0:0.79-1.2.el5.rf set to be updated base/filelists | 3.5 MB 00:00 dell-omsa-indep/filelists | 195 kB 00:01 dell-omsa-specific/filelists | 1.0 kB 00:00 extras/filelists_db | 224 kB 00:00 rpmforge/filelists | 4.8 MB 00:06 updates/filelists_db | 715 kB 00:00 --> Finished Dependency Resolution dbus-libs-1.1.2-15.el5_6.i386 from installed has depsolving problems --> Missing Dependency: dbus = 1.1.2-15.el5_6 is needed by package dbus-libs-1.1.2-15.el5_6.i386 (installed) mkinitrd-5.1.19.6-68.el5_6.1.i386 from installed has depsolving problems --> Missing Dependency: nash = 5.1.19.6-68.el5_6.1 is needed by package mkinitrd-5.1.19.6-68.el5_6.1.i386 (installed) Error: Missing Dependency: nash = 5.1.19.6-68.el5_6.1 is needed by package mkinitrd-5.1.19.6-68.el5_6.1.i386 (installed) Error: Missing Dependency: dbus = 1.1.2-15.el5_6 is needed by package dbus-libs-1.1.2-15.el5_6.i386 (installed) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest The program package-cleanup is found in the yum-utils package. I have tried running package-cleanup --dupes and package-cleanup --problems but to no avail.

  Read the article

• Weird networking problem ( Linksys, Windows 7 )

  - by Rohit Nair

  Okay it's a bit tough to figure out where to start from, but here is the basic summary of the issue: During general internet usage, there are times when any attempt to visit a website stalls at "Waiting for somedomain.com". This problem occurs in Firefox, IE and Chrome. No website will load, INCLUDING the router configuration page at 192.168.1.1. Curiously, ping works fine, and other network apps such as MSN Messenger continue to work and I can send and receive messages. Disconnecting and reconnecting to the wireless network seems to fix the problem for a bit, but there are times when it relapses into not loading after every 2-3 http requests. Restarting the router seems to fix the issue, but it can crop up hours or days later. I have a CCNA cert and I know my way around the Windows family of operating systems, so I'm going to list all the things I've tried here. Other computers on the network seem to suffer the same problem, which makes me think it might be a specific problem with something in Win7. The random nature of this issue makes it a bit difficult to confirm, but I can definitely say that I have experienced this on the following systems: Windows 7 64-bit on my desktop Windows Vista 32-bit on my desktop ( the desktop has 2 wireless NICs and the problem existed on both ) Windows Vista 32-bit on my laptop ( both with wireless and wired ) Windows XP SP3 on another laptop ( both wireless and wired ) Using Wireshark to sniff packets seemed to indicate that although HTTP requests were being SENT out, no packets were coming in to respond to the HTTP request. However, other network apps continued to work i.e I would still receive IMs on Windows Live Messenger. Disabling IPV6 had no effect. Updating router firmware to the latest stock firmware by Linksys had no effect. Switching to dd-wrt firmware had no effect. By "no effect" I mean that although the restart required by firmware updates fixed the problem at the time, it still came back. A couple of weeks back, after a LOT of googling and flipping of various options, I figured it might be a case of router slowdown ( http://www.dd-wrt.com/wiki/index.php/Router%5FSlowdown ) caused by the fact that I occasionally run a torrent client. I tried changing the configuration as suggested in that router slowdown link, and restarted the router. However I have not run the torrent client for 12 days now, and yet I still randomly experience this problem. Currently the computer I am using is running Windows 7 64-bit. I would just like to reiterate some of the reasons that I was confused by the issue. Even the router config page at 192.168.1.1 would not load, indicating that it's not a problem with the WAN link, but probably a router issue or a local computer issue. For some reason, disconnecting and reconnecting to the wireless network immediately seems to fix the problem. Updating the router firmware, even switching to open source firmware did nothing. So it seemed to be a computer issue. On the other hand, I have not seen any mass outrage of people having networking problems with Windows 7 and Linksys routers, especially a problem of this sort, and I have tweaked every network setting I could think of. Although HTTP seems to have trouble, ping works fine, DNS lookups work fine, other networking apps work fine. However if I disconnect from Windows Live Messenger and try to reconnect, it fails to reconnect. So although it could receive data over the existing TCP/IP connection, trying to start a new one failed? Does anyone have any further ideas on debugging or fixing this issue? I am reasonably certain there are no viruses or other malicious apps on my network, and I am also reasonably certain that nobody is accessing my router without my consent. Router: Linksys WRT54G2 1.0 running dd-wrt firmware Wireless Card: Alfa AWUS036H OS: Windows 7 64-bit EDIT: I tried switching to a clean wireless channel free from interference, but the problem still persisted. I tried connecting directly with a cable, but the problem still persisted. Signed A very confused and bewildered geek whose knowledge seems to be useless in the face of this frustrating network issue.

  Read the article

• networking through openstack installed on vm

  - by Mandar Katdare

  I am trying to set up a test installation of Openstack on a Ubuntu 12.04 VM running on a ESXi server. So far I have been able to launch the VMs on the ESXi, however am unable to assign IP addresses to them. As the VM with the Openstack installation has a single public IP, I wish to assign IPs to the VMs create through Openstack so that they can directly interact with the public network itself without having a separate private network. So I feel that bridging would not be the correct option here. But am unable to find the correct documents to go ahead with such an install. My ifconfig looks as follows: eth0 Link encap:Ethernet HWaddr 00:0c:29:6f:8a:d7 inet addr:192.168.4.167 Bcast:192.168.4.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe6f:8ad7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:391640 errors:33 dropped:98 overruns:0 frame:0 TX packets:545044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:40303931 (40.3 MB) TX bytes:763127348 (763.1 MB) Interrupt:18 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:146127 errors:0 dropped:0 overruns:0 frame:0 TX packets:146127 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:799815763 (799.8 MB) TX bytes:799815763 (799.8 MB) virbr0 Link encap:Ethernet HWaddr 8a:80:33:32:63:a0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) The eth0 is the adapter that I intend to use for all communication. My nova.conf looks as follows: --dhcpbridge_flagfile=/etc/nova/nova.conf --dhcpbridge=/usr/bin/nova-dhcpbridge --logdir=/var/log/nova --state_path=/var/lib/nova --lock_path=/var/lock/nova --allow_admin_api=true --use_deprecated_auth=false --auth_strategy=keystone --scheduler_driver=nova.scheduler.simple.SimpleScheduler --s3_host=192.168.4.167 --ec2_host=192.168.4.167 --rabbit_host=192.168.4.167 --cc_host=192.168.4.167 --nova_url=http://192.168.4.167:8774/v1.1/ --routing_source_ip=192.168.4.167 --glance_api_servers=192.168.4.167:9292 --image_service=nova.image.glance.GlanceImageService --iscsi_ip_prefix=192.168.4 --sql_connection=mysql://novadbadmin:[email protected]/nova --ec2_url=http://192.168.4.167:8773/services/Cloud --keystone_ec2_url=http://192.168.4.167:5000/v2.0/ec2tokens --api_paste_config=/etc/nova/api-paste.ini --libvirt_type=kvm --libvirt_use_virtio_for_bridges=true --start_guests_on_host_boot=true --resume_guests_state_on_host_boot=true --vnc_enabled=true --vncproxy_url=http://192.168.4.167:6080 --vnc_console_proxy_url=http://192.168.4.167:6080 # network specific settings --network_manager=nova.network.manager.FlatDHCPManager --public_interface=eth0 --vmwareapi_host_ip=192.168.4.254 --vmwareapi_host_username=**** --vmwareapi_host_password=**** --vmwareapi_wsdl_loc=http://127.0.0.1:8080/wsdl/vim25/vimService.wsdl --fixed_range=192.168.4.190/24 --floating_range=192.168.4.190/24 --network_size=32 --flat_network_dhcp_start=192.168.4.190 --flat_injected=False --force_dhcp_release --iscsi_helper=tgtadm --connection_type=vmwareapi --root_helper=sudo nova-rootwrap --verbose --libvirt_use_virtio_for_bridges --ec2_private_dns_show --novnc_enabled=true --novncproxy_base_url=http://192.168.4.167:6080/vnc_auto.html --vncserver_proxyclient_address=192.168.4.167 --vncserver_listen=192.168.4.167 192.168.4.167 is my VM with the Openstack installation and 192.168.4.254 is my ESXi server on which the VM runs. Can anyone advice me about how to proceed? Thanks, Mandar

  Read the article

• Ubuntu: Failure to login with multiple video adapters

  - by tsilb

  Forgive my ignorance, for I am a complete linux noob. I have a computer with three video cards and six monitors. Works great on Windows. Trying to get it to run Ubuntu as well. It loads fine when I have it configured to run on one adapter; detects both screens, runs ok. But I want to turn the other 4 monitors on and run the whole thing as one extended desktop (one session, etc). So I downloaded and installed the newest ATI driver for Linux, which seems to work, kinda. I ran this to set up the screens: aticonfig --adapter=all --initial -f Now when I boot, Ubuntu seems to turn on all the screens (3 viewports, each with two cloned displays from what I can tell). When I enter my login info OR move the mouse off the main screen, the screens freeze and the kbd/ms become unresponsive. aticonfig generated xorg.conf included below. Have tried the following: aticonfig -initial -f - works, but only detects the primary adapter and 2 screens aticccle - Tells me I have to reboot after enabling the other cards. Then goes into above described freezing state. aticonfig --adapter=all --initial -f - see above Manually editing xorg.conf file with my limited knowledge - Was able to get two adapters running, but only the second adapter initialized while the primary stopped at the Ubuntu boot screen. Was unable to see the login prompt. Froze after I logged in blindly (was able to hear the login sound). Using generic "radeon" driver instead of ATI Proprietary driver with the above init attempts Toggling xinerama Various combinations of the above Hardware: Intel Core 2 Quad q6600 8GB DDR2 (3x) ATI Radeon HD 4680 5 monitors (21W, 21W, 22W Portrait, 22W Portrait, 19")and an HDTV (26"W, HDMI) in a horizontal arrangement I know next to nothing about Linux/Ubuntu aside from basic filesystem navigation, editing text files, and accessing my local and networked Windows stores and shares. Basically this is the most advanced thing I've had to do. I installed today. Please advise how to make this configuration work. my xorg.conf: Section "ServerLayout" Identifier "Layout0" Screen 0 "aticonfig-Screen[0]-0" 0 0 Screen "aticonfig-Screen[1]-0" RightOf "aticonfig-Screen[0]-0" Screen "aticonfig-Screen[2]-0" RightOf "aticonfig-Screen[1]-0" Option "RenderAccel" "true" Option "AllowGLXWithComposite" "true" EndSection Section "Files" EndSection Section "Module" EndSection Section "ServerFlags" Option "Xinerama" "0" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[2]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "aticonfig-Device[1]-0" Driver "fglrx" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "aticonfig-Device[2]-0" Driver "fglrx" BusID "PCI:4:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-0" Device "aticonfig-Device[1]-0" Monitor "aticonfig-Monitor[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[2]-0" Device "aticonfig-Device[2]-0" Monitor "aticonfig-Monitor[2]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• XenServer 6.0.2 path to installation media contains non-ascii characters

  - by cmaduro

  XenServer 6.0.2 install fails no matter what I do. I have confirmed that the md5 checksum on my ISO file is good. I tried installing from a mounted ISO file (remotely via iKVM). I tried installing from physical media. I tried installing from a bootable USB stick (using syslinux + contents of the ISO) All attempts have yielded the same result: When verifying the installation media, at 0% initializing, the following is reported: "Some packages appeared to be damaged." followed by a list of pretty much all the gz2 and rpm packages. If I skip the media verification the installer proceeds and then gives me an error when it reaches "Installing from base pack" at 0% which states "An unrecoverable error has occurred. The error was: 'ascii' codec can't decode byte 0xff in position 20710: ordinal not in range(128) Please refer to your user guide, or contact a Technical Support Representative, for further details" there is one option left which is to reboot. Apparently at some point during the processing of the repositories on the installation media non-ascii characters are found, which causes the installer to quit. How do I fix this? Here are my specs TYAN S8236 motherboard 2 AMD Opteron 6234 processors LSI2008 card connected to 2 1TB Seagate Constellation drives SATA, 1 500GB Corsair m4 SSD SATA and 1 Corsair Forse 3 - 64GB SSD SATA Onboard SATA connected to a slim DVD-+RW. Onboard SAS connected to 2 IBM ESX 70GB 10K SAS drives (for XenServer) 256GB memory ================================================================================= Comments: According to pylonsbook.com "chances are you have run into a problem with character sets, encodings, and Unicode" – cmaduro 10 hours ago A clue is provided by "vmware.com/support/vsphere5/doc/…; Data migration fails if the path to the vCenter Server installation media contains non-ASCII characters When this problem occurs, an error message similar to: 'ascii' codec can't decode byte 0xd0 in position 30: ordinal not in range(128) appears, and the installer quits unexpectedly during the data migration process. – cmaduro 10 hours ago This is an error that python throws. And guess what, the .py extention of the file you have to edit in this link community.spiceworks.com/how_to/show/1168 means the installer is written in python. Python is interpreted, so now to find the install file responsible for this error. – cmaduro 6 hours ago The file that generates the error upon verification is /opt/xensource/installer/tui/repo.py. The error message appears around line 359. – cmaduro 2 hours ago I am fairly sure that the install error is generated somewhere in repository.py as the backend.py file throws errors while methods in that file are being called. Perhaps all errors can be traced back to this file. – cmaduro 1 hour ago

  Read the article

• passwd ldap request to ActiveDirectory fails on half of 2500 users

  - by groovehunter

  We just setup ActiveDirectory in my company and imported all linux users and groups. On the linux client: (configured to ask ldap in nsswitch.conf): If i do a common ldapsearch to the AD ldap server i get the complete number of about 2580 users. But if i do this it only gets a part of all users, 1221 in number: getent passwd | wc -l Running it with strace shows kind of attempt to reconnect My ideas were: Does the linux authentication procedure run ldapsearch with a parameter incompatible to AD ldap ? Or probably it is a encoding issue. The windows user are entered in AD with all kind of characters. Maybe someone could shed light on this and give a hint how to debug that further!? Here's our ldap.conf host audc01.mycompany.de audc03.mycompany.de base ou=location,dc=mycompany,dc=de ldap_version 3 binddn cn=manager,ou=location,dc=mycompany,dc=de bindpw Password timelimit 120 idle_timelimit 3600 nss_base_passwd cn=users,cn=import,ou=location,dc=mycompany,dc=de?sub nss_base_group ou=location,dc=mycompany,dc=de?sub # RFC 2307 (AD) mappings nss_map_objectclass posixAccount User # nss_map_objectclass shadowAccount User nss_map_objectclass posixGroup Group nss_map_attribute uid sAMAccountName nss_map_attribute cn sAMAccountName # Display Name nss_map_attribute gecos cn ## nss_map_attribute homeDirectory unixHomeDirectory nss_map_attribute loginShell msSFU30LoginShell # PAM attributes pam_login_attribute sAMAccountName # Location based login pam_groupdn CN=Location-AU-Login,OU=au,OU=Location,DC=mycompany,DC=de pam_member_attribute msSFU30PosixMember ## pam_lookup_policy yes pam_filter objectclass=User nss_initgroups_ignoreusers avahi,avahi-autoipd,backup,bin,couchdb,daemon,games,gdm,gnats,haldaemon,hplip,irc,kernoops,libuuid,list,lp,mail,man,messagebus,news,proxy,pulse,root,rtkit,saned,speech-dispatcher,statd,sync,sys,syslog,usbmux,uucp,www-data and here the stacktrace from strace getent passwd poll([{fd=4, events=POLLIN|POLLPRI|POLLERR|POLLHUP}], 1, 120000) = 1 ([{fd=4, revents=POLLIN}]) read(4, "0\204\0\0\0A\2\1", 8) = 8 read(4, "\4e\204\0\0\0\7\n\1\0\4\0\4\0\240\204\0\0\0+0\204\0\0\0%\4\0261.2."..., 63) = 63 stat64("/etc/ldap.conf", {st_mode=S_IFREG|0644, st_size=1151, ...}) = 0 geteuid32() = 12560 getsockname(4, {sa_family=AF_INET, sin_port=htons(60334), sin_addr=inet_addr("10.1.35.51")}, [16]) = 0 getpeername(4, {sa_family=AF_INET, sin_port=htons(389), sin_addr=inet_addr("10.1.5.81")}, [16]) = 0 time(NULL) = 1297684722 rt_sigaction(SIGPIPE, {SIG_DFL, [], 0}, NULL, 8) = 0 munmap(0xb7617000, 1721) = 0 close(3) = 0 rt_sigaction(SIGPIPE, {SIG_IGN, [], 0}, {SIG_DFL, [], 0}, 8) = 0 rt_sigaction(SIGPIPE, {SIG_DFL, [], 0}, NULL, 8) = 0 rt_sigaction(SIGPIPE, {SIG_IGN, [], 0}, {SIG_DFL, [], 0}, 8) = 0 write(4, "0\5\2\1\5B\0", 7) = 7 shutdown(4, 2 /* send and receive */) = 0 close(4) = 0 shutdown(-1, 2 /* send and receive */) = -1 EBADF (Bad file descriptor) close(-1) = -1 EBADF (Bad file descriptor) exit_group(0) = ?

  Read the article

• Server 2003 R2 doesn't allow logon after a few days of uptime

  - by Bryan

  We have a server 2003 R2 standard (which I'll refer to as SRV01) that's knocking on a bit now, but it still acts as a file, print and SQL server on our company's network. SRV01 hosts user profiles, home directories and pretty much all our business data. Note our AD is currently at 2008 R2 level. This server is due to be upgraded in the next 12 months, but I've no budget to spend on it just yet. A bit of history of this server follows: When SRV01 was first commissioned, it acted as a domain controller (with the same 2003 R2 install it has today), paired with another server that ran Server 2003 R2 SBS. A few years ago, we purchased a pair of dedicated DCs (2008 R2) and at this point we decommissioned the 2003 SBS server, and SRV01 was DCPROMOed out of the AD. Up until very recently, SRV01 used to run Exchange 2003, however we've recently purchased a dedicated server for Exchange 2010 and upgraded (following Microsoft recommended upgrade path). Exchange 2003 was recently uninstalled. - Cleanly to the best of my knowledge. Ever since Exchange was removed from SRV01, I'm finding that after a few days of uptime, when I attempt to logon, pressing CTRL-ALT-DEL just hides the Welcome to Windows Server 2003 banner, and never presents the logon dialog. All I see is a moveable mouse pointer and a blank background. It's a similar story with an admin TS session, the RDP client connects and gives me a blank background, but no logon dialog is presented. The RDP session indefinitely hangs until I give up and close it. The only way I've been able to gain access to the server is to pull the plug on it. Whilst the server does have a battery backed up RAID 5 controller, I'm unhappy about having to do this, so as a temporary measure, I've created a scheduled job to reboot SRV01 each night. Not only do I not like the idea of scheduling a reboot of a server like this, but it is also causing problems for users that leave desktop PCs left logged on overnight. Users complain of 'Delayed Write Failures', and there has also been a number of users that have started to complain about account lockout problems, as well as users not able to connect to shares on SRV01 until they reboot their desktop PCs. I've examined event logs on SRV01 and on the DCs looking for clues as to what the problem is, but there really is nothing untoward being logged. How could I being to investigate this problem when nothing of any relevance is being logged? Is there some additional logging that can be enabled that might give some clues as to what could be causing this problem? Could performance monitor help me out here, and if so, what counters would you consider monitoring? It's worth mentioning that whilst the server is unresponsive via the console and TS, it does still respond to clients connecting to shares without problems for several days, but after about a week I then start to hear users reporting problems accessing shares, but this seems quite sporadic. I've also tried leaving the console logged on (and locked), when I notice I can no longer logon via TS, I can unlock the server console without problem, but it refuses to reboot/shutdown, and subsequent attempts to reboot report that a system shutdown is already in progress and the system then completely hangs. I've tried playing the waiting game for several hours thinking that a timeout might allow the shutdown to continue, but to no avail.

  Read the article

• vagrant up command very slow on OS X Lion

  - by Andy Hume

  When I run vagrant up to provision a new VM on Lion it takes an extremely long time, during which the entire Mac is very laggy and unresponsive. The output is as follows, the key point being the "notice: Finished catalog run in 754.28 seconds" > vagrant up [default] Importing base box 'lucid64'... [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.1.0 VirtualBox Version: 4.1.6 [default] Matching MAC address for NAT networking... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- ssh: 22 => 2222 (adapter 1) [default] -- web: 80 => 4567 (adapter 1) [default] Creating shared folders metadata... [default] Running any VM customizations... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] VM booted and ready for use! [default] Mounting shared folders... [default] -- v-root: /vagrant [default] -- v-data: /var/www [default] -- manifests: /tmp/vagrant-puppet/manifests [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: /Stage[main]/Lucid64/Package[apache2]/ensure: ensure changed 'purged' to 'present' [default] [default] notice: /Stage[main]/Lucid64/File[/etc/motd]/ensure: defined content as '{md5}a25e31ba9b8489da9cd5751c447a1741' [default] [default] notice: Finished catalog run in 754.28 seconds [default] [default] err: /File[/var/lib/puppet/rrd]/ensure: change from absent to directory failed: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: change from absent to directory failed: Could not find group puppet [default] [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: Finished catalog run in 2.05 seconds [default] [default] err: /File[/var/lib/puppet/rrd]: Could not evaluate: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: Could not evaluate: Could not find group puppet [default] [default] Running provisioner: Vagrant::Provisioners::Puppet... [default] Running Puppet with lucid64.pp... [default] stdin: is not a tty [default] notice: /Stage[main]/Lucid64/Exec[apt-update]/returns: executed successfully [default] [default] notice: Finished catalog run in 1.36 seconds [default] [default] err: /File[/var/lib/puppet/rrd]: Could not evaluate: Could not find group puppet [default] [default] err: Could not send report: Got 1 failure(s) while initializing: Could not evaluate: Could not find group puppet [default] >

  Read the article

• Ububtu server 12.04 auto installation freezes at kickseeding running if ks.cfg has post scripts

  - by john206

  I'm trying to make a custom Ubuntu Server iso file. Kickstart file (ks.cfg) runs smooth when there is no %post in the file and Ubuntu installs correctly with ks configuration. Installation finishes installing base, apt, grub and It echos: Kickseed Running... and it freezes @ 0% I thought may be apt-get update doesnt work in ks file, I tried to install other apps like apache2 but no luck I have created dozen iso images and installed them in Virtual Box.I have been googling for 3 days and checked out ubuntu forums but haven't figured out the issue. I appreciate your help. This is how I made the iso image. My ks.file and txt.cfg files located in isolinux directory: root@ubuntu:/home/work mount -o loop ubuntu-12.04-amd64.iso original-iso/ rsync -a original-iso/ custom-iso/ cp ks.cfg custom-iso/isolinux/ cp txt.cfg custom-iso/isolinux/ chmod -R 777 custom-iso/ #Creating Iso image mkisofs -D -r -V “$IMAGE_NAME” -cache-inodes -J -l -b isolinux/isolinux.bin -c isolinux/boot.cat -no-emul-boot -boot-load-size 4 -boot-info-table -o ~/ubuntu-12.04-alternate-custom-amd64.iso custom-iso/ ks.cfg #Generated by Kickstart Configurator #platform=AMD64 or Intel EM64T #System language lang en_US #Language modules to install langsupport en_US #System keyboard keyboard us #System mouse mouse #System timezone timezone America/Los_Angeles #Root password rootpw --iscrypted somethingsomething #Initial user user ubuntu --fullname "ubuntu" --iscrypted --password somethingsomething. #Reboot after installation reboot #Use text mode install text #Install OS instead of upgrade install #Use CDROM installation media cdrom #System bootloader configuration bootloader --location=mbr #Clear the Master Boot Record zerombr yes #Partition clearing information clearpart --all --initlabel #Disk partitioning information part /boot --size 128 --fstype=ext3 --asprimary part / --size 512 --fstype=ext3 --asprimary part swap --size 512 part /tmp --size 512 --fstype=ext3 part /var --size 512 --fstype=ext3 part /usr --size 4096 --fstype=ext3 part /home --size 2048 --fstype=ext3 #System authorization infomation auth --useshadow --enablemd5 #Network information network --bootproto=dhcp --device=eth0 #Firewall configuration firewall --disabled --http --ftp --ssh #X Window System configuration information xconfig --depth=32 --resolution=1024x768 --defaultdesktop=GNOME %post apt-get update mkdir /home/user txt.cfg default autoinstall label autoinstall menu label ^Install Custom Ubuntu Server kernel /install/vmlinuz append file=/cdrom/preseed/ubuntu-server.seed initrd=/install/initrd.gz quiet ks=cdrom:/isolinux/ks.cfg -- label install menu label ^Install Ubuntu Server kernel /install/vmlinuz append file=/cdrom/preseed/ubuntu-server.seed vga=788 initrd=/install/initrd.gz quiet -- label cloud menu label ^Multiple server install with MAAS kernel /install/vmlinuz append modules=maas-enlist-udeb vga=788 initrd=/install/initrd.gz quiet -- label check menu label ^Check disc for defects kernel /install/vmlinuz append MENU=/bin/cdrom-checker-menu vga=788 initrd=/install/initrd.gz quiet -- label memtest menu label Test ^memory kernel /install/mt86plus label hd menu label ^Boot from first hard disk localboot 0x80

  Read the article

• multiple webapps in tomcat -- what is the optimal architecture?

  - by rvdb

  I am maintaining a growing base of mainly Cocoon-2.1-based web applications [http://cocoon.apache.org/2.1/], deployed in a Tomcat servlet container [http://tomcat.apache.org/], and proxied with an Apache http server [http://httpd.apache.org/docs/2.2/]. I am conceptually struggling with the best way to deploy multiple web applications in Tomcat. Since I'm not a Java programmer and we don't have any sysadmin staff I have to figure out myself what is the most sensible way to do this. My setup has evolved through 2 scenarios and I'm considering a third for maximal separation of the distinct webapps. [1] 1 Tomcat instance, 1 Cocoon instance, multiple webapps -tomcat |_ webapps |_ webapp1 |_ webapp2 |_ webapp[n] |_ WEB-INF (with Cocoon libs) This was my first approach: just drop all web applications inside a single Cocoon webapps folder inside a single Tomcat container. This seemed to run fine, I did not encounter any memory issues. However, this poses a maintainability drawback, as some Cocoon components are subject to updates, which often affect the webapp coding. Hence, updating Cocoon becomes unwieldy: since all webapps share the same pool of Cocoon components, updating one of them would require the code in all web applications to be updated simultaneously. In order to isolate the web applications, I moved to the second scenario. [2] 1 Tomcat instance, each webapp in its dedicated Cocoon environment -tomcat |_ webapps |_ webapp1 | |_ WEB-INF (with Cocoon libs) |_ webapp1 | |_ WEB-INF (with Cocoon libs) |_ webapp[n] |_ WEB-INF (with Cocoon libs) This approach separates all webapps into their own Cocoon environment, run inside a single Tomcat container. In theory, this works fine: all webapps can be updated independently. However, this soon results in PermGenSpace errors. It seemed that I could manage the problem by increasing memory allocation for Tomcat, but I realise this isn't a structural solution, and that overloading a single Tomcat in this way is prone to future memory errors. This set me thinking about the third scenario. [3] multiple Tomcat instances, each with a single webapp in its dedicated Cocoon environment -tomcat |_ webapps |_ webapp1 |_ WEB-INF (with Cocoon libs) -tomcat |_ webapps |_ webapp2 |_ WEB-INF (with Cocoon libs) -tomcat |_ webapps |_ webapp[n] |_ WEB-INF (with Cocoon libs) I haven't tried this approach, but am thinking of the $CATALINA_BASE variable. A single Tomcat distribution can be multiply instanciated with different $CATALINA_BASE environments, each pointing to a Cocoon instance with its own webapp. I wonder whether such an approach could avoid the structural memory-related problems of approach [2], or will the same issues apply? On the other hand, this approach would complicate management of the Apache http frontend, as it will require the AJP connectors of the different Tomcat instances to be listening at different ports. Hence, Apache's worker configuration has to be updated and reloaded whenever a new webapp (in its own Tomcat instance) is added. And there seems no way to reload worker.properties without restarting the entire Apache http server. Is there perhaps another / more dynamic way of 'modularizing' multiple Tomcat-served webapps, or can one of these scenarios be refined? Any thoughts, suggestions, advice much appreciated. Ron

  Read the article

• Graphite SQLite3 DatabaseError: attempt to write a readonly database

  - by Anadi Misra

  Running graphite under apache httpd, with slqite database, I have the correct folder permissions [root@liaan55 httpd]# ls -ltr /var/lib | grep graphite drwxr-xr-x. 2 apache apache 4096 Aug 23 19:36 graphite-web and [root@liaan55 httpd]# ls -ltr /var/lib/graphite-web/ total 68 -rw-r--r--. 1 apache apache 65536 Aug 23 19:46 graphite.db syncdb also seems to have gone fine [root@liaan55 httpd]# sudo -su apache bash-4.1$ whoami apache bash-4.1$ python /usr/lib/python2.6/site-packages/graphite/manage.py syncdb /usr/lib/python2.6/site-packages/graphite/settings.py:231: UserWarning: SECRET_KEY is set to an unsafe default. This should be set in local_settings.py for better security warn('SECRET_KEY is set to an unsafe default. This should be set in local_settings.py for better security') /usr/lib/python2.6/site-packages/django/conf/__init__.py:75: DeprecationWarning: The ADMIN_MEDIA_PREFIX setting has been removed; use STATIC_URL instead. "use STATIC_URL instead.", DeprecationWarning) /usr/lib/python2.6/site-packages/django/core/cache/__init__.py:82: DeprecationWarning: settings.CACHE_* is deprecated; use settings.CACHES instead. DeprecationWarning Creating tables ... Creating table account_profile Creating table account_variable Creating table account_view Creating table account_window Creating table account_mygraph Creating table dashboard_dashboard_owners Creating table dashboard_dashboard Creating table events_event Creating table auth_permission Creating table auth_group_permissions Creating table auth_group Creating table auth_user_user_permissions Creating table auth_user_groups Creating table auth_user Creating table django_session Creating table django_admin_log Creating table django_content_type Creating table tagging_tag Creating table tagging_taggeditem You just installed Django's auth system, which means you don't have any superusers defined. Would you like to create one now? (yes/no): yes Username (leave blank to use 'apache'): root E-mail address: [email protected] Password: Password (again): Superuser created successfully. Installing custom SQL ... Installing indexes ... Installed 0 object(s) from 0 fixture(s) bash-4.1$ exit and the local-settings.py file is as follows STORAGE_DIR = '/var/lib/graphite-web' INDEX_FILE = '/var/lib/graphite-web/index' DATABASES = { 'default': { 'NAME': '/var/lib/graphite-web/graphite.db', 'ENGINE': 'django.db.backends.sqlite3', 'USER': '', 'PASSWORD': '', 'HOST': '', 'PORT': '' } } I still get this error [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] File "/usr/lib/python2.6/site-packages/django/db/backends/sqlite3/base.py", line 344, in execute [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] return Database.Cursor.execute(self, query, params) [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] DatabaseError: attempt to write a readonly database not sure what is missing in this configuration

  Read the article

• Configuring OpenLDAP as a Active Directory Proxy

  - by vadensumbra

  We try to set up an Active Directory server for company-wide authentication. Some of the servers that should authenticate against the AD are placed in a DMZ, so we thought of using a LDAP-server as a proxy, so that only 1 server in the DMZ has to connect to the LAN where the AD-server is placed). With some googling it was no problem to configure the slapd (see slapd.conf below) and it seemed to work when using the ldapsearch tool, so we tried to use it in apache2 htaccess to authenticate the user over the LDAP-proxy. And here comes the problem: We found out the username in the AD is stored in the attribute 'sAMAccountName' so we configured it in .htaccess (see below) but the login didn't work. In the syslog we found out that the filter for the ldapsearch was not (like it should be) '(&(objectClass=*)(sAMAccountName=authtest01))' but '(&(objectClass=*)(?=undefined))' which we found out is slapd's way to show that the attribute do not exists or the value is syntactically wrong for this attribute. We thought of a missing schema and found the microsoft.schema (and the .std / .ext ones of it) and tried to include them in the slapd.conf. Which does not work. We found no working schemata so we just picked out the part about the sAMAccountName and build a microsoft.minimal.schema (see below) that we included. Now we get the more precise log in the syslog: Jun 16 13:32:04 breauthsrv01 slapd[21229]: get_ava: illegal value for attributeType sAMAccountName Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SRCH base="ou=oraise,dc=int,dc=oraise,dc=de" scope=2 deref=3 filter="(&(objectClass=\*)(?sAMAccountName=authtest01))" Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SRCH attr=sAMAccountName Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SEARCH RESULT tag=101 err=0 nentries=0 text= Using our Apache htaccess directly with the AD via LDAP works though. Anyone got a working setup? Thanks for any help in advance: slapd.conf: allow bind_v2 include /etc/ldap/schema/core.schema ... include /etc/ldap/schema/microsoft.minimal.schema ... backend ldap database ldap suffix "ou=xxx,dc=int,dc=xxx,dc=de" uri "ldap://80.156.177.161:389" acl-bind bindmethod=simple binddn="CN=authtest01,ou=GPO-Test,ou=xxx,dc=int,dc=xxx,dc=de" credentials=xxxxx .htaccess: AuthBasicProvider ldap AuthType basic AuthName "AuthTest" AuthLDAPURL "ldap://breauthsrv01.xxx.de:389/OU=xxx,DC=int,DC=xxx,DC=de?sAMAccountName?sub" AuthzLDAPAuthoritative On AuthLDAPGroupAttribute member AuthLDAPBindDN CN=authtest02,OU=GPO-Test,OU=xxx,DC=int,DC=xxx,DC=de AuthLDAPBindPassword test123 Require valid-user microsoft.minimal.schema: attributetype ( 1.2.840.113556.1.4.221 NAME 'sAMAccountName' SYNTAX '1.3.6.1.4.1.1466.115.121.1.15' SINGLE-VALUE )

  Read the article

• OSX 10.6.6 SSH md5 break-in check

  - by Alex

  Information Recently one of the linux servers that I access was compromised to steal passwords and ssh keys using a modified ssh binary. This lead me to question if the attacker had compromised my OSX Laptop which had ssh access turned on. A sophos virus scan turned up nothing, and I did not have rkhunter installed before the attack, so I could not compare hashes of the system binaries to be sure. However because OSX is relatively standard for each of their major releases, I asked fiends for md5 hashes md5 /usr/bin/ssh and md5 /usr/sbin/sshd as a basic first check to see if there was anything different about my machine. A few emails later I have found the following data: Version (Arch) [N] MD5 (/usr/bin/ssh) MD5 (/usr/sbin/sshd) OSX 10.5.8 (PPC) [3] 1e9fd483eef23464ec61c815f7984d61 9d32a36294565368728c18de466e69f1 OSX 10.5.8 (intel) [5] 1e9fd483eef23464ec61c815f7984d61 9d32a36294565368728c18de466e69f1 OSX 10.6.x (intel) [7] 591fbe723011c17b6ce41c537353b059 e781fad4fc86cf652f6df22106e0bf0e OSX 10.6.x (intel) [4] 58be068ad5e575c303ec348a1c71d48b 33dafd419194b04a558c8404b484f650 Mine 10.6.6 (intel) df344cc00a294c91230c65e8b7332a79 b5094ccf4cd074aaf573d4f5df75906a where N is the number of machines with with that MD5, and the last row is my laptop. The sample is relatively heterogeneous spaning a few years of different makes and models of Apples, and different versions of 10.6.x. The different hash for my system made me worried that these binaries might have been compromised. So I made sure that my backup for the week was good, and dived into formatting my system and reinstalling OSX. After reinstalling OSX from the manufacturer DVD, I found that the MD5 hash did not change for either ssh, or sshd. Goal Make sure that my system is does not have any malicious software. Should I be worried that this base install of OSX (with no other software installed) has been compromised? I have also updated my system to 10.6.6 and found no change as well. Other Information I am not sure if this is helpful information, but my laptop is a i7 15 inch MacBook Pro bought in Nov 2010, and here is some output from system_profiler: System Software Overview: System Version: Mac OS X 10.6.6 (10J567) Kernel Version: Darwin 10.6.0 64-bit Kernel and Extensions: No Time since boot: 1:37 Hardware: Hardware Overview: Model Name: MacBook Model Identifier: MacBook6,2 Processor Name: Intel Core i7 Processor Speed: 2.66 GHz Number Of Processors: 1 Total Number Of Cores: 2 L2 Cache (per core): 256 KB L3 Cache: 4 MB Memory: 4 GB Processor Interconnect Speed: 4.8 GT/s Boot ROM Version: MBP61.0057.B0C SMC Version (system): 1.58f16 Sudden Motion Sensor: State: Enabled On the laptop, I find: $ codesign -vvv /usr/bin/ssh /usr/bin/ssh: valid on disk /usr/bin/ssh: satisfies its Designated Requirement $ codesign -vvv /usr/sbin/sshd /usr/sbin/sshd: valid on disk /usr/sbin/sshd: satisfies its Designated Requirement $ ls -la /usr/bin/ssh -rwxr-xr-x 1 root wheel 1001520 Feb 11 2010 /usr/bin/ssh $ ls -la /usr/sbin/sshd -rwxr-xr-x 1 root wheel 1304800 Feb 11 2010 /usr/sbin/sshd $ ls -la /sbin/md5 -r-xr-xr-x 1 root wheel 65232 May 18 2009 /sbin/md5 Update So far I have not gotten an answer about this question, but if you could help by increasing the number of hashes that I can compare against, that would be great. To get hashes, and version numbers, run the following on osx: md5 /usr/bin/ssh md5 /usr/sbin/sshd ssh -V sw_vers

  Read the article

• Apache Solr Admin on Tomcat Deployed in WebApps Directory

  - by KM01

  I am trying to get Apache Solr to work on Redhat6 and Tomcat6 (using these instructions), but get this error when browsing to the admin section, http://localhost:8080/solr-example/admin: HTTP Status 404 - missing core name in path type Status report message missing core name in path description The requested resource (missing core name in path) is not available. http://localhost:8080/solr-example loads fine, with a link to "Solr Admin." My setup is as follows: tomcat6: /etc/tomcat6 Solr: /app/solr/example I have a solr-example.xml in /etc/tomcat6/Catalina/localhost/, which reads: <?xml version="1.0" encoding="utf-8"?> <Context docBase="/app/solr/example/apache-solr-3.4.0.war" debug="0" crossContext="true"> <Environment name="solr/home" type="java.lang.String" value="/app/solr/example" override="true"/> </Context> I don't see anything in the logs (/var/log/tomcat6) ... only entires in catalina.out are regarding the starting and stopping of tomcat6. My questions are: 1.What else do I need to do to get "Solr Admin" to work under Tomcat? 2.Where are these "cores" supposed to be specified? I see an entry in /app/solr/example/solr/solr.xml ? <solr persistent="false"> adminPath: RequestHandler path to manage cores. If 'null' (or absent), cores will not be manageable via request handler <cores adminPath="/admin/cores" defaultCoreName="collection1"> <core name="collection1" instanceDir="." /> </cores> </solr> 3.How do I got about ensuring that logs are working correctly? I can't find logs that contain mention of the 404 above. Update in response to @quanta's comment: Downloaded former (apache-solr-3.4.0.tgz) dataDir was not set, now set to: <dataDir>${solr.data.dir:../solr/data}</dataDir> JAVA_OPTS: /usr/lib/jvm/java/bin/java -classpath :/usr/share/tomcat6/bin/bootstrap.jar:/usr/share/tomcat6/bin/tomcat-juli.jar:/usr/share/java/commons-daemon.jar -Dcatalina.base=/usr/share/tomcat6 -Dcatalina.home=/usr/share/tomcat6 -Djava.endorsed.dirs= -Djava.io.tmpdir=/var/cache/tomcat6/temp -Djava.util.logging.config.file=/usr/share/tomcat6/conf/logging.properties -Djava.util.logging.manager=org.apache.juli.ClassLoaderLogManager org.apache.catalina.startup.Bootstrap start catalina.out contains no indication of the above error

  Read the article

• ActiveMQ Pure Master / Slave - Out of sync

  - by pico

  What i have : 1 master broker and 1 slave broker both in ActiveMQ 5.4.0 What i use : waitForSlave on master side and failover uri on slave side (in the master connector URI) What i want to do : I want to wait some delay (like 5 seconds) in case of a tiny network failures between master and slave before starting slave transpôrt connectors So i put this in slave config : <broker xmlns="http://activemq.apache.org/schema/core" brokerName="slave" dataDirectory="${activemq.base}/data" useJmx="true" persistent="true" populateJMSXUserID="true" masterConnectorURI="failover://(tcp://master:61616)?initialReconnectDelay=1000&amp;maxReconnectDelay=30000" shutdownOnMasterFailure="false" advisorySupport="false"> It seems to work but after a network hang between master and slave, the slave reconnect successfully and then the master logs a lot of : 2010-10-18 17:08:44,421 | ERROR | Slave Failed | org.apache.activemq.broker.ft.MasterBroker | ActiveMQ Task java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1040-634226732611718750-0:0 at org.apache.activemq.broker.MapTransportConnectionStateRegister.lookupConnectionState(MapTransportConnectionStateRegister.java:93) at org.apache.activemq.broker.TransportConnection.lookupConnectionState(TransportConnection.java:1412) at org.apache.activemq.broker.TransportConnection.processRemoveConsumer(TransportConnection.java:561) at org.apache.activemq.command.RemoveInfo.visit(RemoveInfo.java:76) at org.apache.activemq.broker.TransportConnection.service(TransportConnection.java:309) at org.apache.activemq.broker.TransportConnection$1.onCommand(TransportConnection.java:185) at org.apache.activemq.transport.ResponseCorrelator.onCommand(ResponseCorrelator.java:116) at org.apache.activemq.transport.TransportFilter.onCommand(TransportFilter.java:69) at org.apache.activemq.transport.vm.VMTransport.iterate(VMTransport.java:218) at org.apache.activemq.thread.DedicatedTaskRunner.runTask(DedicatedTaskRunner.java:98) at org.apache.activemq.thread.DedicatedTaskRunner$1.run(DedicatedTaskRunner.java:36) On the slave side everything is fine. So after that, i've tried to stop the master to see if the slave is capable of turning master after these "network hangs". The master took long time to shutdown (10 seconds) and then some error message appears in slave logs : 2010-10-18 17:09:32,915 | WARN | Async error occurred: java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1049-634226732657812500-0:3 | org.apache.activemq.broker.TransportConnection.Service | VMTransport: vm://slave#5 java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1049-634226732657812500-0:3 at org.apache.activemq.broker.MapTransportConnectionStateRegister.lookupConnectionState(MapTransportConnectionStateRegister.java:93) at org.apache.activemq.broker.TransportConnection.lookupConnectionState(TransportConnection.java:1412) at org.apache.activemq.broker.TransportConnection.processRemoveSession(TransportConnection.java:600) at org.apache.activemq.command.RemoveInfo.visit(RemoveInfo.java:74) at org.apache.activemq.broker.TransportConnection.service(TransportConnection.java:309) at org.apache.activemq.broker.TransportConnection$1.onCommand(TransportConnection.java:185) at org.apache.activemq.transport.ResponseCorrelator.onCommand(ResponseCorrelator.java:116) at org.apache.activemq.transport.TransportFilter.onCommand(TransportFilter.java:69) at org.apache.activemq.transport.vm.VMTransport.iterate(VMTransport.java:218) at org.apache.activemq.thread.DedicatedTaskRunner.runTask(DedicatedTaskRunner.java:98) at org.apache.activemq.thread.DedicatedTaskRunner$1.run(DedicatedTaskRunner.java:36) Are they any ways to keep my kaha stores (they are individual stores) synchronised? The main problem is that the slave never turn master after a master failure, it stay block on this message : 2010-10-18 17:09:33,681 | WARN | Transport (master/172.21.60.61:61616) failed to tcp://master:61616 , attempting to automatically reconnect due to: java.net.SocketException: Software caused connection abort: socket write error | org.apache.activemq.transport.failover.FailoverTransport | ActiveMQ Transport: tcp://master/172.21.60.61:61616 I'm totally stuck with these syncs problems, any help welcome! Regards

  Read the article

• Why is user asked to choose their workgroup?

  - by Clinton Blackmore

  We running Mac OS X Server 10.5.8 with Mac OS X 10.5.8 clients. Students use network logins to, well, log in. I've been asked to deny internet access to a specific user. I was told that a good way to do it is to create a user workgroup called "No Internet Access" and manage settings there. (Specifically, I told parental controls to allow access to no sites, and blacklisted all the installed web browsers). Now, when the user authenticates to log in, they are greeted with this dialog: Workgroups for <username> Grade 7 Students No Internet Access It is unlikely that the student would willing choose "No Internet Access" to be their base group. Looking in Workgroup Manager at the student's record, it shows their primary group ID is the grade 7 group, and "No Internet Access" is listed as another group they belong to. I looked at the managed preferences for all the computers pertaining to logins. They are set to their defaults. Specifically, the computer groups' preference for Logins - Access has the defaults: [unchecked] Ignore workgroup nesting [checked] Combine available workgroup settings Based on my reading of Tips and Tricks for Mac Administrators, this should be correct, the user should not be asked which group they belong to, and settings from all applicable groups should be applied. How can I achieve that result? Edit: I've decided to add some additional information from the Tips and Tricks for Mac Management White Paper (via Apple in Education, via the author's site). On page 21, it says: With Leopard MCX, workgroup preference settings are combined by default into a single set of values. This means that instead of having to choose between the Math, Science, or Language Arts workgroups when logging in, a user can just authenticate and be taken directly to the desktop. All the settings for each of those workgroups are composited together, providing you with all the Dock items and a composite of all the other settings. On page 40, an example is given in which settings are combined from different 'domains', one computer group, two (user) workgroups, and one individual user's settings. [When johnd logs into a leopard client,] the items staged in the Dock from left to right are: computer group, first workgroup alphabetically, second workgroup, user. Items within the workgroup are staged alphabetically. Nowhere is there an indication that groups are nested; indeed, I can see no sensible (non-flat) heirarchy for groups like Math, Science, and Language Arts. I strongly believe that there is a way to apply settings from two unrelated user workgroups such that a user of OS X 10.5.x or newer does not need to choose their workgroup. This is what I seek to achieve.

  Read the article

• What is a good method to solve cabal install problems?

  - by sp3ctum

  I've used the cabal package manager for Haskell programs to install libraries and new projects that I've cloned from some repositories. More often than not, I keep running into problems. Most projects make installing them seem super easy, but in my case that's not always true - sometimes they are very hard to get running. Some are so hard, in fact, that I've lost interest in the project solely because of not being able to install it. So instead of complaining, I'd like to ask what I should do to better this situation. I'd like to use my most recent problem as an example. I'm interested in trying out the Gitit project. It's a promising looking personal wiki that runs on various version control systems. So here's what I've done: Clone from Github run cabal install in the project directory like I'm told on the project install page: mika@eka:~/git/gitit$ ls BLUETRIP-LICENSE CHANGES HCAR-gitit.tex LICENSE Network README.markdown RELANN-0.6.1 Setup.lhs TANGOICONS YUI-LICENSE data expireGititCache.hs gitit.cabal gitit.hs plugins mika@eka:~/git/gitit$ cabal install Resolving dependencies... cabal: cannot configure happstack-server-7.0.7. It requires base64-bytestring ==1.0.* For the dependency on base64-bytestring ==1.0.* there are these packages: base64-bytestring-1.0.0.0. However none of them are available. base64-bytestring-1.0.0.0 was excluded because gitit-0.10 requires base64-bytestring ==0.1.* mika@eka:~/git/gitit$ So now I'm thinking: well, I'll install happstack-server on its own, maybe that will work: mika@eka:~/git/gitit$ cabal install happstack-server Resolving dependencies... Warning: happstack-server.cabal: Ignoring unknown section type: test-suite Configuring happstack-server-7.0.7... cabal: At least the following dependencies are missing: blaze-html ==0.5.*, hslogger >=1.0.2, monad-control ==0.3.*, network >=2.2.3, sendfile >=0.7.1 && <0.8, system-filepath >=0.3.1, text >=0.10 && <0.12, threads >=0.5, transformers-base ==0.4.* cabal: Error: some packages failed to install: happstack-server-7.0.7 failed during the configure step. The exception was: ExitFailure 1 So looks like there are some dependencies missing. But isn't installing these dependencies the whole point of using cabal in the first place? What should I do? File bug reports (to which project?), install the dependencies manually or something else? Bonus points for explaining what causes these kinds of problems.

  Read the article

• Cannot run a VM with more than three network interfaces with KVM

  - by Bostonvaulter

  I'm running KVM on top of Ubuntu 10.10 Server I can create VM's (Virtual Machine) and network interfaces fine but I cannot seem to add more than three network interfaces. As soon as I have a VM with four network interfaces it gets stuck on startup at the starting SeaBIOS page with this message: Starting SeaBIOS (version pre-0.6.1-20100702_143500-palmer) So far I've verified this with two VM's, a Ubuntu 10.10 desktop and a Vyatta router. The specific network hardware I assign to the VM's doesn't seem to matter. I'm trying to have one bridged interface and three private networks using Vyatta to route between them. Does anyone know why I can't run a VM with more than three network interfaces? Edit: Additionally the KVM thread responsible for the specific VM hangs using ~100% CPU (i.e. one core). Here's the command for the process that is hanging: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1,sockets=1,cores=1,threads=1 -name vyatta -uuid 6dff7c94-6810-423e-5fea-fec10da0e9b7 -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/vyatta.monitor,server,nowait -mon chardev=monitor,mode=readline -rtc base=utc -boot c -drive file=/home/rams/virtual-machines/vyatta.img,if=none,id=drive-ide0-0-0,boot=on,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -device rtl8139,vlan=0,id=net0,mac=00:54:00:be:cc:4b,bus=pci.0,addr=0x3 -net tap,fd=97,vlan=0,name=hostnet0 -device rtl8139,vlan=1,id=net1,mac=52:54:00:da:59:ed,bus=pci.0,addr=0x5 -net tap,fd=98,vlan=1,name=hostnet1 -device rtl8139,vlan=2,id=net2,mac=52:54:00:ce:22:b6,bus=pci.0,addr=0x6 -net tap,fd=99,vlan=2,name=hostnet2 -device rtl8139,vlan=3,id=net3,mac=52:54:00:1e:bc:46,bus=pci.0,addr=0x7 -net tap,fd=101,vlan=3,name=hostnet3 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -vnc 127.0.0.1:0 -k en-us -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 Edit: I've also found an error in dmesg that might be related (it also shows up when running virtd in verbose mode): 14:47:24.399: warning : qemudParsePCIDeviceStrs:1422 : Unexpected exit status '1', qemu probably failed I've also tried disabling app armor but that doesn't seem to make a difference.

  Read the article

< Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >