Search Results

Search found 13692 results on 548 pages for 'bad practices'.

Page 447/548 | < Previous Page | 443 444 445 446 447 448 449 450 451 452 453 454  | Next Page >

• What was your biggest waste of money, and what should you have bought instead? [closed]

  - by rob

  I waste a lot of money on computer equipment and other electronics that I don't really need. I've also bought software that I've never really used, or which as been replaced by better free software. As I'm buying things, it doesn't seem like much--fifty bucks here, a hundred dollars there. But when I go back and look at how much I've spent over my past few electronics purchases, I usually start to think of the other things I could have bought with that money instead. Most of the computer hardware and electronics don't usually improve my life by much, if at all. Case in point: back when I was in college, I prided myself on getting the best deals for computer hardware, but when I went back and added up all the money I had spent, I had probably wasted close to a thousand dollars on "cheap" $100 hard drives that eventually all went bad (including the warranty replacements). Even if they did still work, it would not be worth the effort to use them, because they're too small and too noisy by today's standards. I've also spent thousands more on other junk, such as RAM and CPU upgrades that only gave modest performance jumps, and wireless audio transmitters that I used for a short time to stream music from the now-defunct Yahoo! Music service. Every time I see a really great deal on RAM or video cards, I come one click away from buying them, but these days I'm usually able to resist. I've been wanting to get into woodworking ever since I moved into my house, and five years later I'm finally saving up for a $600 table saw. Sure, I've already got a toolbox and a couple of the essential power tools like a drill and a jigsaw, but I can't help but think that I'd have an entire shop full of woodworking tools and a lot of nice wood furniture if I hadn't wasted all that money back in college. What has been your biggest waste of money on computer stuff and technology? If you had all that money back, would you make the same mistake again and buy the same types of things, or would you spend it on something else?

  Read the article

• which vista services can be disabled with impunity?

  - by GwenKillerby

  I use Vista on a HP pavilion DV2 laptop. When I look through all the services my laptop starts, it really seems there's way too much of it. I multi boot with XP and 7. Both startup in 40 seconds. Vista takes four minutes. Is there some software that can determine which services I don't need? On 7, there's no propietary HP stuff at all, yet it seems to run fine. Because all these service, there's a LOT of them and some just sit there doing nothing, monitoring for updates I don't really need or want or need to know about the second they're available. my laptop is the only computer i use at home, there's no home network, aside from the modem-router, which is cabled, not wifi. Take for instance Parental controls, and stuff for people with bad eyesight, Tablet PC. I really never use any of that stuff. Hope this question is specific enough. I've looked at the other questions but they didn't answer me. thanks, Gwen.

  Read the article

• git : The remote end hung up unexpectedly - too many simultaneous users?

  - by Pritam Barhate

  I asked this first on StackOverflow and I was suggested that I should ask it here: We have a self hosted git server (Gitolite) on a VPS account (CPU:2.68GHz RAM:1824MB). This same VPS is also used to publish our underdevelopment web apps for client demos. (Very little traffic). so the main use of the server is as a Git Server Only. This git server is accessed by a team of 30-40 people for various projects. Our problem is that during the day when 6-7 people are trying to access the server (sometimes same repo) we get frequent error message: ssh: connect to host xxx.xxx.xx.xx port 22: Bad file number fatal: The remote end hung up unexpectedly After trying for 10-15 minutes it generally succeeds. During early mornings and late nights when there are only 1-2 people, git commands work with 100% success rate. Also I would like to note that if I access the other file hosted on the server through HTTP it works fine. I found a couple of questions on StackOverflow and on other sites regarding this. But most of the people point towards SSH key set up or conflicts between Msysgit and Cygns SSH. However I don't think this is the problem in our case as we get this behavior on Windows (using msysgit only) as well as Mac Machines. Also if it was SSH configuration issue then it shouldn't work at all. But in our case it works after 10-15 minutes. I think in our case it might be too many simultaneous connections to same server (or same repo) or something like that. Does there exists a setting or a conf file that needs to modified to solve this problem? Please help me solve this problem or point me in the right direction. Thanks in advance. Pritam.

  Read the article

• Nginx/puma rhel unix socket permission error?

  - by Kevin Brown

  When I try to start my puma server, I get the error: /.rvm/gems/ruby-2.1.1/gems/puma-2.9.0/lib/puma/binder.rb:275:in `initialize': Permission denied - connect(2) for "/var/run/nvhbase.sock" (Errno::EACCES) My sites-available/nvhbase.conf file: upstream nvhbase { server unix:/var/run/nvhbase.sock; } server { listen 80 default_server; server_name 207.131.132.219; root /home/vf032500/dev/nvh/public; location / { proxy_pass http://unix:/var/run/nvhbase.sock; proxy_http_version 1.1; proxy_set_header Upgrade $http_upgrade; proxy_set_header Connection $connection_upgrade; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Proto https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } } I don't know a lot about unix sockets and everything works fine using tcp/puma default. My rails app is in my user directory. Is that the problem?? socket is starting in /var/run--I can start in /tmp, but I've heard that's bad practice? Provided I start the server in /tmp, I then can't access it via the server's ip--then what? I'm happy to provide any needed info, I just don't know a whole lot about server/nginx/puma.

  Read the article

• Problem with Outlook 2010 (SMTP AUTH LOGIN)

  - by Filipe YaBa Polido

  I have to connect one customer Outlook 2010 to a remote server on which I have either no right, neither way to talk to the sysadmin. This is the thing, after installing and reviewing the logs on Wireshark: Outlook Express: HELO machine AUTH LOGIN username base64 encoded password base64 encoded mails go through. Outlook 2010: HELO machine AUTH DIGEST-MD5 response from server Outlook sends just a * AUTH LOGIN password base64 encoded So... I can send mails in the same domain, but can't send outside, it gives me a relay denied message. My point is... Why the h**l Outlook 2010 doesn't send the username AND the password?! It can never login the right way :| With other versions of Outlook it works fine, and with OE works great, it auths and allows to send mail to a different domain. I've googled and nothing worked. I'm pretty sure that I'm not alone with this one. My last resort will be to configure a local proxy/server that relays to the original one :| Any help would be appreciated. Sorry my bad english as is not my natural language. Thanks.

  Read the article

• Best NIC config when virtual servers need iSCSI storage?

  - by icky2000

  I have a Windows 2008 server running Hyper-V. There are 6 NICs on the server configured like this: NIC01 & NIC02: teamed administrative interface (RDP, mgmt, etc) NIC03: connected to iSCSI VLAN #1 NIC04: connected to iSCSI VLAN #2 NIC05: dedicated to one virtual switch for VMs NIC06: dedicated to another virtual switch for VMs The iSCSI NICs are used obviously for storage to host the VMs. I put half the VMs on the host on the switch assigned to NIC05 and the other half on the switch assigned to NIC06. We have multiple production networks that the VMs could appear on so the switch ports that NIC05 & NIC06 are connected to are trunked and we then tag the NIC on the VM for the appropriate VLAN. No clustering on this host. Now I wish to assign some iSCSI storage direct to a VM. As I see it I have 2 options: Add the iSCSI VLANs to the trunked ports (NIC05 and NIC06), add two NICs to the VM that needs iSCSI storage, and tag them for the iSCSI VLANs Create two additional virtual switches on the host. Assign one to NIC03 and one to NIC04. Add two NICs to the VM that needs iSCSI storage and let them share that path to the SAN with the host. I'm wondering about how much overhead the VLAN tagging in Hyper-V has and haven't seen any discussion about that. I'm also a bit concerned that something funky on the iSCSI-connected VM could saturate the iSCSI NICs or cause some other problem that could threaten storage access for the entire host which would be bad. Any thoughts or suggestions? How do you configure your hosts when VMs connect direct to iSCSI?

  Read the article

• Rebuilding LVM after RAID recovery

  - by Xiong Chiamiov

  I have 4 disks RAID-5ed to create md0, and another 4 disks RAID-5ed to create md1. These are then combined via LVM to create one partition. There was a power outage while I was gone, and when I got back, it looked like one of the disks in md1 was out of sync - mdadm kept claiming that it only could find 3 of the 4 drives. The only thing I could do to get anything to happen was to use mdadm --create on those four disks, then let it rebuild the array. This seemed like a bad idea to me, but none of the stuff I had was critical (although it'd take a while to get it all back), and a thread somewhere claimed that this would fix things. If this trashed all of my data, then I suppose you can stop reading and just tell me that. After waiting four hours for the array to rebuild, md1 looked fine (I guess), but the lvm was complaining about not being able to find a device with the correct UUID, presumably because md1 changed UUIDs. I used the pvcreate and vgcfgrestore commands as documented here. Attempting to run an lvchange -a y on it, however, gives me a resume ioctl failed message. Is there any hope for me to recover my data, or have I completely mucked it up?

  Read the article

• Why isn't my phone charging with some micro usb cables?

  - by Jacxel

  I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

  Read the article

• ORA- 01157 / Cant connect to database

  - by Tom

  Hi everyone, this is a follow up from this question. Let me start by saying that i am NOT a DBA, so i'm really really lost with this. A few weeks ago, we lost contact with one of our SID'S. All the other services are working, but this one in particular is not. What we got was this message when trying to connect ORA-01033: ORACLE initialization or shutdown in progress An attempt to alter database open ended up in ORA-01157: cannot identify/lock data file 6 - see DBWR trace file ORA-01110: data file 6: '/u01/app/oracle/oradata/xxx/xxx_data.dbf' I tried to shutdown / restart the database, but got this message. Total System Global Area 566231040 bytes Fixed Size 1220604 bytes Variable Size 117440516 bytes Database Buffers 444596224 bytes Redo Buffers 2973696 bytes Database mounted. ORA-01157: cannot identify/lock data file 6 - see DBWR trace file ORA-01110: data file 6: '/u01/app/oracle/oradata/xxx/xxx_data.dbf' When all continued the same, I erased the dbf files (rm xxx_data.dbf xxx_index.dbf), and recreated them using touch xxx_data.dbf. I also tried to recreate the tablespaces using `CREATE TABLESPACE DATA DATAFILE XXX_DATA.DBF` and got Database not open As I said, i don't know how bad this is, or how far i'm from gaining access to my database (well, to this SID at least, the others are working). I would imagine that a last resource would be to throw everything away, and recreating it, but I don't know how to, and I was hoping there's a less destructive solution. Any help will be greatly appreciated . Thanks in advance.

  Read the article

• Connecting to same public IP from different locations yields different results

  - by DHall

  Since yesterday I've been unable to access one of my favorite time-wasting sites, boston.com. It starts to load but then it gets redirected to pagesinxt or something like that. After some investigation, I've narrowed it down to an issue with cache.boston.com, but only from my work location. I found the IP (216.38.160.107) , but even that doesn't work correctly from here at work. When I do a telnet 216.38.160.107 80 GET http://cache.boston.com/universal/css/hp_bgcom.css from another location, I get a nice long CSS, as expected. From here, I get an error (trimmed for size): HTTP/1.1 400 Bad Request Your request could not be processed. Request could not be handled This could be caused by a misconfiguration, or possibly a malformed request. For assistance, contact your network support team. Is there any way I can troubleshoot this further on my end? Tracert doesn't tell me anything too useful: Tracing route to vwrpx1.ttn.xpc-mii.net [216.38.160.107] over a maximum of 30 hops: 1 * * * Request timed out. Since it's not really work-related, I don't really want to bring it up to our network team unless I know what's going on, or if there's some risk to the network (ex. malware or something)

  Read the article

• My Reverse DNS PTR record seems to be right, but I'm still getting bouncing email

  - by johnbr

  Hello, I have a service (statusme.com) where I let people know (for example) that their kid's soccer games are cancelled because of bad weather. We send out emails to the people who have registered. I have a second server as a backup, (vps.statusme.com) and I've set up the application to send some of the email through the second server. But I'm getting complaints from various recipient SMTP servers that the email is considered spam. So I did some investigating, and it appears that they think my reverse DNS record isn't correct. But when I look at it via various rDNS websites and instructions I found elsewhere on ServerFault, everything looks correct: jb$ host -t a vps.statusme.com 8.8.8.8 Using domain server: Name: 8.8.8.8 Address: 8.8.8.8#53 Aliases: vps.statusme.com has address 66.84.8.246 jb$ host -t ptr 246.8.84.66.in-addr.arpa 8.8.8.8 Using domain server: Name: 8.8.8.8 Address: 8.8.8.8#53 Aliases: 246.8.84.66.in-addr.arpa domain name pointer vps.statusme.com. I'm confused about what I'm doing wrong. Thanks for any suggestions.

  Read the article

• Most cost efficient way to backup Subversion data to S3?

  - by sludge

  I'm looking at using S3 as an offsite backup repo for my Subversion database. When I dump my SVN database, it's about 10 gigabytes. I would like to avoid the charge of uploading that data repeatedly. The anatomy of this large file such that new changes to Subversion modify the tail of the file, with everything else staying the same. Because Amazon S3 does not allow you to "patch" files with changes, I will have to upload ten gigs every time I instantiate a backup after doing a simple submit to Subversion. Here are the options as I see them: Option 1 I am looking at duplicity which has --volsize which splits data over an amount of megs. Is it possible to split the Subversion dumps using this so further incremental backups are measured in megabytes? Option 2 Can I just backup the hot subversion repository? This seems like a bad idea if it is in the middle of writing a submit. However, I have the option of taking the repo offline between the hours of midnight and 4am. Each revision in my Berkeley DB uses a file as its record.

  Read the article

• ubuntu 9.10 installer doesn't recognize the hard drive

  - by dan

  I downloaded Ubuntu 9.10 x86_64 and am trying to install it on a fairly modern system with a Gigabyte GA-MA770-UD3 motherboard. Ubuntu 9.04 installed fine and still will when I stick that disc in, but 9.10 doesn't see my hard drive (western digital 250GB). If I boot from the disc, I can install gparted and it does recognize the drive, but when I try to start the install process from the live disc, Ubuntu again doesn't recognize the hard drive. I checked /var/log/messages and see this: Nov 12 17:28:08 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was bad, boot with 'nodmraid'. Nov 12 17:28:08 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: no raid sets and with names: "nvidia_ciiajheb-0" Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. I checked my BIOS, SATA is enabled and is set to IDE mode, so there shouldn't be software RAID, but nonetheless, I added nodmraid to the boot line and tried again. It still doesn't recognize the drive. I checked /var/log/messages again and now see this: Nov 12 17:49:38 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was boad, boot with 'nodmraid'. Nov 12 17:49:38 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Any ideas on things to try? I've tried all of the various BIOS settings for SATA. IDE,RAID, etc. Nothing seems to work.

  Read the article

• Messed up partitions... system will not boot!

  - by someguy

  I did a really dumb thing. cfdisk threw an error at me saying "FATAL ERROR: Bad primary partition 3: Partition ends in the final partial cylinder", so I installed Partition Table Doctor to see if I could fix the problem. When the program started up, it told me there were problems with my partitions, and asked if I wanted them fixed (cannot remember real message, but I believe it had something to do with the cylinder boundaries), so, blindly, without thinking of the consequences, I did. Now, my system will not boot. I tried booting from the Windows 7 installation CD. I went to install a fresh copy, but it said that "No drives were found". I then opened up diskpart. According to diskpart, there is only one partition, containing one volume, assigned the letter "C". Before, I had four partitions! It is also saying that the file system is RAW. Is there any way I can fix this? I have important data that I do not want to lose. Later on... I tried fdisk with the option -l, which lists the partition table(s), and this is what I got: Ignoring extra extended partition 4 Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 64 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x163df116 Device Boot Start End Blocks Id System /dev/sda1 6 18 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 18 7851 62918572+ 7 HPFS/NTFS /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30403 139203193 7 HPFS/NTFS I don't know if this will help, but it's extra information, at least. Also, this is how I had my partitions: 40MB (Unallocated) 100MB (System Reserved) 60GB (Windows, C:) 40GB (Was reserved for secondary OS) ~132GB (Home, E:)

  Read the article

• How to transform a csv to combine matching rows?

  - by Christian Wolf

  I have a CSV file with some transaction data. Let's say date, volume, price and direction (sell/buy). Additionally there is a ID for each transaction and on each closing transaction (the newer one) there is a reference to the corresponding transaction. Classical database referencing. Now I want to do some statistics and draw some plots. This could be done via Octave, LaTeX/TikZ, Gnuplot or whatever. To do this I need both buy and sell price in one row. My thought was to preprocess the CSV to get another CSV containing the needed information and then to do the statistics. In the end I'd like to have a solution based on scripts and not on a spreadsheet as data might change often (exported from online DB). My actual solution (see http://paste.ubuntu.com/6262822/ ) is a bash script that parses the CSV line by line and checks if there exists a corresponding transaction. If found, a new row is written to the destination CSV. If not a warning is printed. The bad news: For each row in the source file I have to read the whole file a few times. This causes long running times of 10sec for 300 lines. As the line number might rise soon (10k lines), this is not perfect. I am aware, that there are many shells to be opened in the script which might cause the performance problems. Now my questions: Is bash/awk/sed/.... a good way to do things? Should I first import all data into a "real" local database to use SQL? Is there an easy way to achieve the desired results?

  Read the article

• NTFS frequent corruption when writing many small files, index $I30 error

  - by david sedai

  I'm running Windows 7 Ultimate on a laptop with a 500G HDD, and had all partitions formatted as NTFS. I do a lot of programming and LaTeX typesetting, both of these involves a large amount of reading/writing/deleting to a lot of small files, such as C++ library headers or LaTeX packages. The problem is that frequently, when there is a large number of writing to files, the partition being written to often corrupts, the chkntfs e: returns dirty, where e: is the partition being written. I've re-formatted the drive, I've contacted the laptop manufacturer and had the HDD checked, the HDD is not faulty, there are no bad sectors, and I've tried a brand new HDD, to no avail, and the other partition on the same physical drive doesn't have this issue. I'm pretty sure that it's no hardware related. I've searched the Microsoft support pages, one page http://support.microsoft.com/kb/982018 provides an update for Advanced Format Disks, which I've already installed. The chkntfs log shows $130 index errors. I'm at a loss here. Can anyone help? Thanks in advance.

  Read the article

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• Win 7 x64 explorer.exe stops responding on copy/paste

  - by Sourabh

  Few months ago I changed my Win7 orb using this software. But it changed only the explorer.exe in C:\Windows. To solve that, I copied explorer.exe from there to C:\Windows\system32 and C:\Windows\SysWOW64 (Probably a bad idea). Things were working fine until a few days ago, it started giving me problems while copying. Sometimes, when I copy/paste, It works fine but sometimes it stays on that dialog box which looks like it is doing pre-copying things like counting number of files/file size etc. But its not. It stays on that screen forever. Now if I try to close it, title changes to cancelling but rest stays the same. If I try to close it too many times, explorer.exe crashes. And its not related to file-size. It may crash for 4Mb file and work fine for 10Gb file but some other time, it'll do the opposite. Is there any way to reset my explorer.exe and Is this because of explorer.exe or something else PS: I forgot to take backup of explorer.exe. PS2: I didn't install any software or downloaded anything that could harm my computer. EDIT I tried System Restore and SFC /scannow but they didn't help.

  Read the article

• Automated Syslog Error Solution Finder

  - by Dru

  Any automated syslog solution finding frameworks? I want my central syslog server to email a list of problems, their severity and suggested solutions. There have been several questions about centralising system logs and alternative log analysis systems, but I don't get the impression that any of them help with issue resolution. A little background: At work I am now literally doing the work of two people, and both jobs have expanded beyond their initial frameworks. It is not so bad as I have helpers, but they are little more than smart monkeys. While one of my predecessors [I have two, that is how I know I have the jobs of two people] set-up logwatch to email its results out, my monkeys don't have the skills necessary to identify unimportant data. This has caused all of them, and myself sadly, to setup email filters and ignore the whole thing until something goes "bang". It would be handy to have someone else tell them what is important, what is connected, and to suggest a few ways to resolve the issue (I could train then to research the solution first, ha!). My reading of the Splunk and Octopussy sites indicates that I still need to bring my own highly trained monkey to the party. Which I am several years from having.

  Read the article

• How do I determine how future-proof and stable a router is?

  - by Aarthi

  I mentioned in my last question that my wireless router had a bad habit of crashing. After consulting with the Super User chatroom, as well as my sysadmin, I've decided I may as well purchase a new router. However, I'm unsure how to evaluate all these tech specs that get touted about. The two things that seem to be the most important to me are: (1) keeping my router future-proof (as standards evolve and change), and (2) ensuring its stability. Unfortunately, I'm not sure what, exactly, I should be looking for in the tech specs or the item description that can give me a good idea of how stable or future-proof my decide will be. What should I look for? Can I determine stability without having to try the device out myself? Please note: I'm not a battle-hardened power user by any means, so I'll likely be reliant on the given firmware for my router. My last router lasted me like four years, so I mostly just want something that'll cover a 500 sqft apartment in New York with minimal crashing, so that I can watch Hulu in peace. And make Skype calls. If it helps, the router models that I'm currently decided between are this ASUS one and this LinkSys one.

  Read the article

• I can't get my PC to start up by a normal way.

  - by ssice

  I couldn't write a more accurate title. I am just unable to start the computer by pressing the Power On button. I checked the Power Supply and it seems to give good voltage values in every pin. And this is not a BIOS malfunction because of bad overclocking or anything that may come to your mind. And I will tell you why. It happens that EPS (or any ATX-based) power supply has the ability to be powered-on by the Motherboard by jumping the 13th pin of the 24-pin-ATX-connector to COM/GND. I did it, after pushing the power on button (without any visual response) and, pwhaa! The machine turned on. I was able to read (and even write, if I wanted) BIOS values and then start any OS installed. Machine starts, so it's not any kind of misconfiguration. It seems some hardware related. I am able to power the machine on only if I already pushed the power on button. Though pushing it without jumping the 13th pin to ground for a second does not power the machine. Of course, jumping the pin without pushing the power on button does not tell the motherboard anything, so the computer would not start up either. It's as if the logic that connects the power button with the 13th pin derivation to GND was unable to be activated. What can be the issue? How can I solve it? My configuration is as follows: CPU: AMD Phenom 9850 X4 Black Edition MB: ASUS Formula II AM2 RAM: 2x2GB Corsair Dominator 5-5-5-15 2T @ 1066MHz DDR2 Tested also with only 1 module GPU: 2x XFX nVIDIA GeForce 9600 GT XxX Alpha Dog Edition @ Core: 540Mhz [SLi] Power Supply: Xilence 700W (ATX 12V 2.3 / EPS 12V 2.92 compatible) PS: I know the machine is like 2 years old. I hardly use it now, but my parents do.

  Read the article

• SQL Server Installation: Is it 32 or 64 bit?

  - by CapBBeard

  Hi, Recently I was performing an OS upgrade on one of our DB servers, moving from Server 2003 to Server 2008. The DBMS is SQL Server 2005. While reinstalling SQL on the new Windows installation, I went to another of our DB servers to verify a couple of settings. Now, I always thought this second server was Server 2003 x64 + SQL 2005 x64 (from what I'd been told), but I now have my doubts about this. I now suspect that it is in fact only 32 bit SQL, however I'd like to verify this. Here's some details: The OS is definitely 64 bit. xp_msver shows Platform as NT INTEL X86 SELECT @@VERSION shows Microsoft SQL Server 2005 - 9.00.4035.00 (Intel X86)... However sqlservr.exe is not shown with '* 32' in taskmgr, does anyone know why this is the case, if it is in fact 32 bit as claimed? Despite this, it does seem to be running out of the x86 program files folder. If I do the same checks on a confirmed 64 bit installation, it does give back the expected 64 bit readings, which can only prove that this server in question is only running in 32 bit. Now, that being the case, the question arises about how much memory this '32 bit' install can use. Task manager reports about 3.5GB memory usage for sqlservr.exe (The server has 16GB physical). I suspect that AWE has not been configured at all, and therefore the server will be significantly under-utilised (remembering that the OS is 64 bit) if SQL is simply using a 32bit address space. Is this assumption correct? I feel the server should have SQL reinstalled as 64 bit in order to fully utilise the hardware platform, however it is currently heavily in production; this will be no easy task. I suspect we may just have to configure AWE correctly and let it be for the time being (Unless this is a bad idea?). I apologise that this question is a little vague/lost; I'm no SQL expert, just trying to get a handle on what's going on here.

  Read the article

• How can I create a VLAN on my extreme switch for a separate subnet/domain?

  - by drpcken

  I'm putting together a small active directory implementation for a buddy of mine. I currently have 2 servers (one is the primary domain controller) and a couple clients. I need to test and run updates on every machine on this domain, but I would have plug them into my current LIVE domain to get it internet access. From what I've read having two separate domains on a single subnet is a bad idea (even though it is temporary) so I don't want to risk messing anything up on my production domain. I'm pretty sure I can create a separate VLAN on my extreme 48 port switch and plug this smaller domain into it on a different subnet, but I don't know the commands. Both subnets would need internet access of course (one of the things I can't wrap my head around is routing internet traffic between subnets (gateway is on production subnet). Switch is a Summit x450e-48p My production domain is on subnet 192.168.200.0. My new domain I want to put online would go into subnet 192.168.10.0. A shove in the right direction would be greatly appreciated. Thank you!

  Read the article

• What are the replacement options for an IDE hard disk for a DOS based system?

  - by dummzeuch

  I have got a few "embedded" systems running MSDOS 6.2 which boot from and store data to IDE hard disks. Since these drives are nearing their end of life, the question arises how we can replace them. The requirements are: DOS must be able to install and boot from these drives. They must be able to sustain heavy (mostly) write access. If possible, they should be able to survive moderate vibrations (not too bad since the current hard disks have survived several years of that) I considered the following options so far: other ide hard drives: Unfortunately modern IDE drives are too large so DOS cannot boot from them even if I create small partitions. Older IDE drives are just that: old, so they are probably not the most reliable ones any more. SSDs: There are a few SSDs with IDE interface available. I have not yet tried them. Does anybody have any experience with them? They look like the ideal replacement provided that DOS can boot from them and that writing speed does not deteriorate too much (the old hard disks are no race cars either). Compact Flash: There are adapters for using CF with IDE controllers and they work fine. DOS can boot from them and they have no problems at all with vibrations. What I am not sure about is their durability. DOS uses FAT so some very few sectors are written every time the medium is being written to. IDE to SATA converters: I have no idea whether they are any good. Has anybody tried them? It might be an option to use one of these to connect an SATA SSD to the system. Are there any alternatives that I have missed? (We are working on replacing these systems, but it will still take a few years.)

  Read the article

• Automated Syslog Error Solution Finder

  - by Dru

  Any automated syslog solution finding frameworks? I want my central syslog server to email a list of problems, their severity and suggested solutions. There have been several questions about centralising system logs and alternative log analysis systems, but I don't get the impression that any of them help with issue resolution. A little background: At work I am now literally doing the work of two people, and both jobs have expanded beyond their initial frameworks. It is not so bad as I have helpers, but they are little more than smart monkeys. While one of my predecessors [I have two, that is how I know I have the jobs of two people] set-up logwatch to email its results out, my monkeys don't have the skills necessary to identify unimportant data. This has caused all of them, and myself sadly, to setup email filters and ignore the whole thing until something goes "bang". It would be handy to have someone else tell them what is important, what is connected, and to suggest a few ways to resolve the issue (I could train then to research the solution first, ha!). My reading of the Splunk and Octopussy sites indicates that I still need to bring my own highly trained monkey to the party. Which I am several years from having.

  Read the article

< Previous Page | 443 444 445 446 447 448 449 450 451 452 453 454  | Next Page >