Search Results

Search found 17847 results on 714 pages for 'virtual disk'.

Page 449/714 | < Previous Page | 445 446 447 448 449 450 451 452 453 454 455 456  | Next Page >

• Can't Remove Logical Drive/Array from HP P400

  - by Myles

  This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The host is a DL580 G5 running 64-bit Red Hat Enterprise Linux Server release 5.7 (Tikanga). I am unable to remove the array using either hpacucli or cpqacuxe. I believe it is because of "OS Status: LOCKED". The file system that lives on this array has been unmounted. I do not want to reboot the host. Is there some way to "release" this logical drive so I can remove the array? Note that I do not need to preserve the data on logical drive 2. I intend to physically remove the drives from the machine and replace them with larger drives. I'm using the cciss kernel module that ships with Red Hat 5.7. Here is some information pertaining to the host and the P400 configuration: [root@gort ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.7 (Tikanga) [root@gort ~]# uname -a Linux gort 2.6.18-274.el5 #1 SMP Fri Jul 8 17:36:59 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux [root@gort ~]# rpm -qa | egrep '^(hp|cpq)' cpqacuxe-9.30-15.0 hp-health-9.25-1551.7.rhel5 hpsmh-7.1.2-3 hpdiags-9.3.0-466 hponcfg-3.1.0-0 hp-snmp-agents-9.25-2384.8.rhel5 hpacucli-9.30-15.0 [root@gort ~]# hpacucli HP Array Configuration Utility CLI 9.30.15.0 Detecting Controllers...Done. Type "help" for a list of supported commands. Type "exit" to close the console. => ctrl all show config detail Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Cache Serial Number: PA82C0J9SVW34U RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Logical Drive: 1 Size: 136.7 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 35132 Strip Size: 128 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Unique Identifier: 600508B100184A395356573334550002 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 101 MB, /tmp 7.8 GB, /usr 3.9 GB, /usr/local 2.0 GB, /var 3.9 GB, / 2.0 GB, /local 113.2 GB OS Status: LOCKED Logical Drive Label: A0027AA78DEE Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) Drive Type: Data Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM57RF40000983878FX Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 35 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM55VQC000098388524 Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 36 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Logical Drive: 2 Size: 546.8 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Completed Unique Identifier: 600508B100184A395356573334550003 Disk Name: /dev/cciss/c0d1 Mount Points: None OS Status: LOCKED Logical Drive Label: A5C9C6F81504 Drive Type: Data Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2H5PE00009802NK19 Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 37 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 1I:1:4 Port: 1I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM28YY400009750MKPJ Model: HP DG146ABAB4 Current Temperature (C): 31 Maximum Temperature (C): 36 PHY Count: 1 PHY Transfer Rate: 3.0Gbps physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FGYV00009802N3GN Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 38 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM8AFAK00009920MMV1 Model: HP DG146BB976 Current Temperature (C): 31 Maximum Temperature (C): 41 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:7 Port: 2I Box: 1 Bay: 7 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FJQD00009801MSHQ Model: HP DG146ABAB4 Current Temperature (C): 29 Maximum Temperature (C): 39 PHY Count: 1 PHY Transfer Rate: Unknown

  Read the article

• Nexenta/OpenSolaris filer kernel panic/crash

  - by ewwhite

  I've an x4540 Sun storage server running NexentaStor Enterprise. It's serving NFS over 10GbE CX4 for several VMWare vSphere hosts. There are 30 virtual machines running. For the past few weeks, I've had random crashes spaced 10-14 days apart. This system used to open OpenSolaris and was stable in that arrangement. The crashes trigger the automated system recovery feature on the hardware, forcing a hard system reset. Here's the output from mdb debugger: panic[cpu5]/thread=ffffff003fefbc60: Deadlock: cycle in blocking chain ffffff003fefb570 genunix:turnstile_block+795 () ffffff003fefb5d0 unix:mutex_vector_enter+261 () ffffff003fefb630 zfs:dbuf_find+5d () ffffff003fefb6c0 zfs:dbuf_hold_impl+59 () ffffff003fefb700 zfs:dbuf_hold+2e () ffffff003fefb780 zfs:dmu_buf_hold+8e () ffffff003fefb820 zfs:zap_lockdir+6d () ffffff003fefb8b0 zfs:zap_update+5b () ffffff003fefb930 zfs:zap_increment+9b () ffffff003fefb9b0 zfs:zap_increment_int+68 () ffffff003fefba10 zfs:do_userquota_update+8a () ffffff003fefba70 zfs:dmu_objset_do_userquota_updates+de () ffffff003fefbaf0 zfs:dsl_pool_sync+112 () ffffff003fefbba0 zfs:spa_sync+37b () ffffff003fefbc40 zfs:txg_sync_thread+247 () ffffff003fefbc50 unix:thread_start+8 () Any ideas what this means?

  Read the article

• mac: How to mount ejected external hdd again

  - by Maurice Kroon

  I've used my WD My Book 1TB for quite some time now. I always simply unplug it without officially 'ejecting' it. However, yesterday I did eject it (the partitions) before unplugging it. However, now, when i reconnect the hdd, it does not show the drives. It only shows the WD SmartWare partition (which is empty btw). The rest doesn't start. Does anyone know how to mount an unmounted disk? thx in advance!

  Read the article

• OSX: Undeletable files

  - by geoffjentry

  So via what I suspect is a cron'd rsync gone awry, I noticed that I have ~25000 variants of .DS_Store in a directory that's on an external disk, they're named "..DS_Store.FOO" where FOO varies. The problem is that I can seem to delete them, even using the various tricks I've seen over the years for removing files with oddball names. No problem, I said - I moved all of the real files into another directory and then just tried to do an 'rm -r' on the original directory ... no luck, it fails to delete those files and says directory not empty. Tried it again with 'rm -rf' and still no luck. I have no idea how to get rid of this thing, does anyone have any idea?

  Read the article

• Redirect example.com to www.example.com VPS & Apache2

  - by Thomas Buckley

  I have a VPS and a domain name registered with the provider. When I enter www.example.com my site is displayed correctly, but entering example.com does not work. I am able to ping www.example.com. I added the following line to my apache2 default vhosts file: ServerName example.com ServerAlias www.example.com But this did not work. The VPS is a Debian5 OS. Any ideas? Note: There is no option via a provided control panel to add this, it's a basic package I purchased I know this post answers it but there are no extra comments and I'd like to know if it's the best way: way to redirect page to www using virtual host configuration in sites-available for apache2? Thanks

  Read the article

• I reinstalled OS X and the system was the same as before

  - by slhck

  Strange thing happened. I want so sell my old Macbook and therefore used a disk image of the Snow Leopard DVD that I restored onto an external drive. I booted off the drive and went through the installation steps. Now I really would like to perform "archive and install", as there might be some files that I need later, but I didn't see the option. The only options for installation I had, were, including others, optional printer drivers and Rosetta. So I just clicked through and I wasn't given any other option. After about 45 minutes, my system booted again, and voila, there was my old system. Nothing changed. How should I proceed to actually reset the system? All I have is that Snow Leopard DVD image.

  Read the article

• Add linux user with restricted access

  - by Dominik Str

  I need to create a user on linux with access rights only to one folder. Background: I have installed git on my virtual server (Debian). I also created a user for the repository. There is a lot of private data on the server. But all folders have read-access for others, because it's needed for the applications which run on the server. So the git-user can see all the data. I would like to restrict the git user only to the folder where the repository is installed. I also tried ACL, but it didn't work. Is there a better way to do this? Thanks in advance!

  Read the article

• Checkpoint FW-1disk full

  - by krugger

  Hi, The logging filled the disk of the managment node. This cause the firewall nodes to start logging locally. After deleting some old logs, restarting the managment node logging is still being done locally at the firewall nodes. I have already done a fw fetchlogs on all firewall nodes to get the local log entries. How can I tell the firewall nodes that they should once again connect to the managment node? My syslog_servers show doesn't show any syslog servers. But the documentation mentions that this is for additional logging and not for logging between firewall nodes and the managment node.

  Read the article

• Installing Intel Rapid Storage Drivers makes my eSATA Drives act weird

  - by Filip Ekberg

  I have a HP 8530w Elitebook this Laptop got an eSATA port which I want to plug my LaCie d2 Quadra V2 1TB harddrive into. It all works well on a fresh install of Windows 7 without the Intel Chipset drivers installed. However when I install the Intel Rapid Storage drivers or the Intel Matrix software my drive seems to "disconnect" when I use it to much. I have a lot of Virtual PC's on the drive and when I start them the disk somewhat disconnects. What could cause this?

  Read the article

• Linux, fdisk: change order of partitions

  - by osgx

  I have a harddrive with 24 logical partitions on it. Half of them are Linux and half are windows. Current ordering is: 3 Linux partitions; 12 windows partitions; 9 Linux partitions. In this setup, Windows can access any of partition (no limits on partition number), but Linux can't access sda16, sda17 ... Can I change numbering of partitions without moving them on disk? I want to put all Linux partitions to be <16; and windows partitions to be 16, so linux will be able to access all linux partitions. I have fdisk/sfdisk and it sees all partitions.

  Read the article

• Static route in conflict with a default route

  - by Ossan Sokiv

  Hi guys, I have a default route configured. 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.1 I'd like to add a static route to pass traffic destined for 192.168.1.51 via a load balancer's redundant virtual interface at 192.168.1.2. ip route add 192.168.1.51 mask 255.255.255.255 via 192.168.1.2 When I try to add the static route I get this error. Error: either "to" is duplicate or "default" is garbage." It doesn't want to add the static route because it's in conflict with the default route. Is there a way around this? Regards Ossan

  Read the article

• Configure Nagios To Alert Depending On Host Group That Service Alert Originates From

  - by StrangeWill

  So my setup: Services are shared between all hosts (CPU/RAM/Disk/Services). Hosts are split into two main groups: "Production" and "Development". We have two contact groups: "Production" and "Development". Lets say my development SQL server runs low on RAM, I want it to only alert those in "Development" contact group (this service is of course assigned to a host in the "Development" host group, using the shared RAM monitoring service). I'm pretty much stumped on this... I can't configure it at the service level (they're shared there), and I can't seem to get escalations to do it for me either... Do I need to use service groups along with escalations and bite the bullet on building that list? Or am I missing something stupidly simple? I'm using Centreon for configuration if that helps.

  Read the article

• Can't Install Windows 2008 R2 on Lenovo Laptop With SSD

  - by Ben

  I am trying to install Windows Server 2008 R2 on a new Lenovo X201 or T410 laptop. Setup halts with the following pop-up: A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the windows installation media is in the CD/DVD drive you can safely remove it for this step. The CD drive is obviously working, as it's booting from CD to get to this point. The only thing I can think is that it is to do with the fact they have SSD disks in - but that's just a guess. (Edit - One extra thing that may or may not be relevant: it's the 64 bit version of Server 2008 R2)

  Read the article

• Cleaning Up Unused Users and Groups (Ubuntu 10.10 Server)

  - by PhpMyCoder

  Hello experts, I'm very much a beginner when it comes to Ubuntu and I've been learning the ropes by diving in and writing a (backend-language independent) web app framework that relies on apache, some clever mod_rewrites, Ubuntu permissions, groups, and users. One thing that really annoys my inner clean-freak is that there are loads of users and groups that are created when Ubuntu is installed that are never used (Or so I think). Since I'm just running a simple web app server, I would like to know: What users/groups can I remove? Since you'll probably ask for it...here's a list of all the users on my box (excluding the ones I know that I need): root daemon bin sys sync man lp mail uucp proxy backup list irc gnats nobody libuuid syslog And a list of all of the groups: root daemon bin sys adm tty disk lp mail uucp man proxy kmem dialout fax voice cdrom floppy tape sudo audio dip backup operator list irc src gnats shadow utmp video sasl plugdev users nogroup libuuid crontab syslog fuse mlocate ssl-cert lpadmin sambashare admin

  Read the article

• Connectivity good between VMs, but no connectivity between host and VM

  - by Greg Sansom

  I have a strange situation where connectivity (ie ping, access shared folders and services) is fine between virtual machines, but not between the host and the virtuals. I've been using Hyper-V almost every day for years and have never had a problem like this. Note the following: The host machine and all virtuals are running Windows Server 2008 r1. All machines can connect to the web, and the gateway router. Subnet mask and gateway reported in ipconfig are identical for all machines. I can access virtuals via the Hyper-V snap-in only. Doea anyone have suggestions about what might be wrong, or what diagnostic steps I can take?

  Read the article

• ESXi 4.1 CentOS 6.X eth0 unnavailable

  - by L.K.

  I don't usually ask for help so directly, usually google have all i need but this time i'm seriously lost. Hope you can help me .s The thing is, i have a server with Vmware ESXi 4.1 and 5 already running and configured virtual servers, but whenever i try to make a new one on CentOS 6.X it leaves me without eth0 to be activated in any way. When installing CentOS, in the screen of localhost.localdomain i try by the button in the left down corner of the screen to make eth0 connect automatically but it tells me a NetworkManager Error: cannot start eth0. So...in command line once the CentOS is already installed, i have configured ifcfg-eth0 and manually tried to take up the eth0 but when i restart network service "Bringing up eth0: Failed" and sometimes even "shutting down eth0: Failed" Thanks in advance

  Read the article

• Pfsense: Inbound Load Balancing https with sticky connection

  - by Zeux

  first of all I'm very sorry for my English... This is my scenario: Internet Firewall+LB: pfsense_1(Active) + pfsense_2(Passive) in CARP Pool servers: 3 x nginx(PHP5+HTTP+HTTPS) Pfsense 1 and 2 CARP configured with Virtual IP (pubblic). Nginx servers's ips are all private. I want to load balance inbound HTTP and HTTPS connections between the 3 nginx web servers. An importat thing is that the HTTPS connections must be "sticky connections": in HTTPS connections, after login by username and password, I setup a php session and therefore when a client starts a HTTPS connection it will be always redirected to the same nginx server, until it disconnects itself, it closes the page/browser or after a timeout (30minutes?) without activity. Is this possible whit the last release(2.0.1) of pfsense? thank you very much...

  Read the article

• What's the difference between keepalived and corosync, others?

  - by Matt

  I'm building a failover firewall for a server cluster and started looking at the various options. I'm more familiar with carp on freebsd, but need to use linux for this project. Searching google has produced several different projects, but no clear information about features they provide . CARP gave virtual interfaces that failover, I am not really clear on whether that's what corosync does, or is that what pacemaker does? On the other hand I did get manage to get keepalived working. However, I noted that corosync provides native support for infiniband. This would be useful for me. Perhaps someone could shed some light on the differences between: corosync keepalive pacemaker heartbeat Which product would be the best fit for router failover?

  Read the article

• Filezilla/Puttygen doesn't recognize private key file

  - by devzoner

  I have generated a key for an Ubuntu Virtual Machine running on Azure Cloud Services http://www.windowsazure.com/en-us/manage/linux/how-to-guides/ssh-into-linux/ openssl req -x509 -nodes -days 365 -newkey rsa:2048 -keyout myPrivateKey.key -out myCert.pem When loading the private key into Filezilla, it asks me to convert the format, however, when converting the key it fails, the same happens with puttygen from linux console, using this: puttygen myPrivateKey.key -o myKey.ppk In both cases I have the following error: puttygen: error loading `myPrivateKey.key': unrecognised key type By the way, this key doesn't have a passphrase. I found an old thread about it, but I'm using 0.6.3 version which is newer than what this thread recommends: http://fixunix.com/ssh/541874-puttygen-unable-import-openssh-key.html I've managed to solve this issue by using another gui client Fugu for Mac, but one of my co-worker uses windows and I still have to figure this out. Since Filezilla is the de-facto ftp client, I thought it would be easier to solve it there. Thanks

  Read the article

• Wired and Wireless USB Network Adapter

  - by Evan M.

  Does anyone know if there are any USB network adapters out there that have both wired and wireless networking capability? Far-fetched, I know, but thought I'd ask. Background: Some of our users have locked down laptops that we also include unlocked virtual machines running on VMware Player. Sometimes the users have a need for network connectivity with their VMs where NAT and bridged networking from the host won't work. To supplement this, we want to supply them with adapters that they can use VMware USB pass through capabilities to provide appropriate connectivity. They will need both wired and wireless capability. Rather than carrying around 2 adapters, was hoping we could get a combination unit so that we can reduce it to 1. Thanks

  Read the article

• IIS7 returns 403.1 (execute access denied) for image file

  - by Kristoffer

  I have a web app running in IIS7 on Windows Server 2008. There is a virtual directory pointing to a shared folder "/Content/Data" on another machine (running Windows Server 2003), as well as a real directory "/Content/Images" on the local machine (web app sub folder). Accessing images in "/Content/Images" is no problem, but when an image (e.g. a JPEG file) in the "/Content/Data" is accessed by a browser, IIS returns this error: HTTP Error 403.1 - Forbidden: Execute access is denied. However, the web app can read and write to / from it. I assume IIS and ASP.NET are running under different user accounts? Does anyone have an idea on what I have to do to make it work? I have set the permissions on the shared folder to Everyone Full Control, with no luck.

  Read the article

• Can / should I prevent my domain controller doing forward lookups for remote users?

  - by markmnl

  I have a Windows Server 2003 server in the office. I VPN into the LAN remotely. My VPN has a virtual NIC with the Windows Server as the primary DNS since it is a domain controller. When connected to the VPN and I do a nslookup or simply browse the web my VPN's DNS (the office's Windows Server) provides the DNS answers - I beleive becuase it has DNS forwarders so queries it cant answer it forwards and then relays the answer. This is the desired behaviour for workstations in the office (they should query their domain controller first). However for remote VPN users this is not desirable - I do not want my remote office's server to answer DNS queries it is not the authority of (which happends to be 192.168.x.x). Is there any way I can configure this?

  Read the article

• Installing Windows Server 2003 on AMD environment

  - by santhosh kumar

  Hi all, Our organisation we have 25 computers and we are trying to setup Windows Server 2003. We are planning to configure Active Directory NAT DNS server Visual Studio Team Foundation Server Subversion (SVN) Trac (Bug tracking tool) FTP server And our Hardware configuration is AMD Athlon 64 X2 Dual (Core processor 5600+, 2.60 GHz) Asus motherboard (M2N series) Transcend 4 GB RAM (800 MHz) 500 GB Hard Disk (RAID enabled) But my colleague is advising me AMD won't suite for servers platforms, and use Intel environment. Also they telling we can't install all the services to one server. I got confusion what to do?... Is really can`t install above services to AMD computer? Thanks...

  Read the article

• Postgres 9.0 locking up, 100% CPU

  - by Jake

  We are having a problem where our Postgres 9.0 server occasionally locks up and kills our webapp. Restarting Postgres fixes the problem. Here's what I've been able to observe: First, usage of one CPU jumps to 100% for a few minutes Disk operations drop to ~0 during this time Database operations drop to 0 (blocks and tuples per sec) Logs show during this time: WARNING: worker took too long to start; cancelled WARNING: worker took too long to start; cancelled No Queries in logs (only those over 200ms are logged) No unusually long-running queries logged before or during Then the second CPU jumps to 100% The number of postgres processes jumps from the usual 8-10 to ~20 Matched by a spike in Postgres Blocks per second (about twice normal) Logs show LOG: could not accept SSL connection: EOF detected Queries are running but slow Restarting postgres returns everything to normal Setup: Server: Amazon EC2 Large Ubuntu 10.04.2 LTS Postgres 9.0.3 Dedicated DB server Does anyone have any idea what's causing this? Or any suggestions about what else I should be checking out?

  Read the article

• gparted won't boot from liveCD

  - by ant2009

  Hello, Fedora 12 2.6.32.9-70.fc12.i686 I downloaded the gparted iso and burnt it to a CD. gparted-live-0.5.2-1 This GParted Live was created by: create-gparted-live -l en -b u -e e -d sid -m http://free.nchc.org.tw/debian -s http://free.nchc.org.tw/debian-security -g http://free.nchc.org.tw/drbl-core -n 2.6.32-3 -i 0.5.2-1 The files and folders: isolinux live syslinux COPYING GParted-Live-Version I put the disk in and reboot. Nothing happens. I just get a flashing cursor in the top left hand corner. I then have to switch of the power button to get it to reboot. I have done this a number of time and the results are the same. Can anyone tell me how to boot from the gparted liveCD? Many thanks for any suggestions,

  Read the article

< Previous Page | 445 446 447 448 449 450 451 452 453 454 455 456  | Next Page >