Search Results

Search found 2018 results on 81 pages for 'bayesian networks'.

Page 45/81 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

• Access points fighting for dominance?

  - by Phillip Oldham

  We have a small office with a large number of wireless devices (a mixture of desktop machines, laptops, and wifi-enabled phones) all working from a single Apple Airport Extreme which extends our wired network. I've added another Airport Extreme for resiliency, since we've been seeing a decrease in performance and (as far as I understand) access points can only handle a small number of clients. I set the new AP to extend the current network so that the clients weren't constantly switching between different wireless networks, however as soon as this AP was configured all the wireless devices started seeing network trouble, flicking on and off. I'm assuming that this is because both APs are reasonably strong, and the client can't decide which to use. What is the best route to follow to resolve this? What I'm aiming for is wireless resiliency; preferably having two APs share the network load, or if this isn't an option then having a primary AP with a "fail-over", should the primary go down for any reason.

  Read the article

• How should I troubleshoot a problematic wireless connection on Linux?

  - by Gearoid Murphy

  I recently purchased a netgear 150 usb wireless dongle for use with my 11.10 Xubuntu amd64 system. Using the network-manager interface, I can see local wireless networks and enter the authentication details for my local wireless lan. Unfortunately, the connection does not seem to work, I keep getting notifications that my wireless has disconnected (but none indicating that I've connected). When I examine syslog, it seems to indicate that I've successfully associated with the wireless switch and that dhcp has successfully acquired an ip address but the log shows that the dhcp process keeps sending requests, eventually dropping the connection. 'ifconfig wlan0' never shows the dhcp address logged in syslog. I suspect that the problem lies with the usb dongle, my configuration or the wireless switch but I am not certain how to isolate the problem, can anyone provide some insight on how I should go about homing in on the cause of this problem or verifying the functionality of the individual components, thanks.

  Read the article

• Windows 8 doesn't automatically join Wi-Fi network if Ethernet connection is active

  - by Herb Caudill

  In Windows 7, my laptop would automatically join both an Ethernet network and the Wi-Fi network in my house (both going through the same router). In Windows 8, if the Ethernet connection is present, it doesn't join the Wi-Fi network at all. The reason I noticed this is that if Wi-Fi isn't active, I don't see my AirPlay speakers. My wireless printer is also unavailable until I manually connect to Wi-Fi. To recap: When I turn on my computer and it's connected to Ethernet, this is what my Network Connections control panel looks like: After I manually join my Wi-Fi network, it looks like this: I would prefer for it to join both networks automatically on startup, the way it did in Windows 7. Is there a way to make this happen?

  Read the article

• Encryption over gigabit carrier ethernet

  - by Roy

  I would like to encrypt traffic between two data centres. Communication between the sites is provided as a standard provider bridge (s-vlan/802.1ad), so that our local vlan tags (c-vlan/802.1q) are preserved on the trunk. The communication traverse several layer 2 hops in the provider network. Border switches on both sides are Catalyst 3750-X with the MACSec service module, but I assume MACSec is out of the question, as I don't see any way to ensure L2 equality between the switches over a trunk, although it may be possible over a provider bridge. MPLS (using EoMPLS) would certainly allow this option, but is not available in this case. Either way, equipment can always be replaced to accommodate technology and topology choices. How do I go about finding viable technology options that can provide layer 2 point-to-point encryption over ethernet carrier networks?

  Read the article

• Windows VPN - NO internet access

  - by sharru

  I host a network of servers behind a Fortigate 200a firewall in the DC. I connect to those servers via a VPN connection. The problem is that when i connect to the VPN, I lose my internet connection on the local PC (windows 7). I would like to be connected to the VPN and still surf the web. i guess this means to only forward a range of ip to the VPN connection. I've read other answers on serverfault, talking about "un-check the 'Use default gateway on remote network' option in your Windows 7 PPTP network connection settings". When i do that , i get internet access but no access to the servers in the VPN. Any idea how to get both working? Should i change something on the fortigate 200a config? Do i need two networks cards? Is there a place in windows to define ip range for the vpn connection?

  Read the article

• Distribute terrabyte files to the public from web server

  - by MarkJ

  Hi We need to set up a website which makes two or three large files publicly available - the files will be 1 or 2 terrabytes each. Although they will be public, in practise I expect only a relatively small number of scientists will want to download them. What is the best way to allow this? I've had a quick talk to a web-hosting provider (rackspace) and they suggested a hybrid solution. An entry-level managed server (we predict fairly low traffic for the website, but we do need to install some custom CGI software). Some cloud storage which hooks into Limelight Networks. This would host the large files, for download by FTP. It sounded OK to me but I know relatively little about server administration. Does it make sense? Thanks in advance, Mark

  Read the article

• Is there a sensible way of 'teaming' two ADSL connections?

  - by Tim Long

  I work in an office complex that has two seperate ADSL connections, which they use to provide two seperate networks (actually both the ADSL routers go into a Cisco managed switch with two VLANs, one for each ADSL connection). Circumstances have changed so that 95% of the users are all on one ADSL connection. It would be great if there were a way to join together both connections to emulate a single connection at double the speed, but the ISP doesn't support bonding. So, is there a sensible way to take two completely seperate ADSL lines and use them to provide a single internet gateway?

  Read the article

• Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

  - by Andrew Bolster

  I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

  Read the article

• How do I access an Ubuntu VirtualBox guest at a static IP from an OS X host?

  - by David Siegel

  How does one configure an Ubuntu guest to use a static IP that's visible to an OS X host, and ensure that the static IP is independent of the host's network configuration? I previously used bridged networking for my guest, but I'm constantly moving my host between networks so the guest IP is always different. First, I tried setting the guest network configuration to NAT and forwarding host port 1022 to guest port 22, so I could at least ssh to a fixed address (localhost:1022): $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/Protocol" "TCP" $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/GuestPort" 22 $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/HostPort" 1022 Then, $ ssh localhost -p 1022 ssh: connect to host localhost port 1022: Connection refused But this didn't work (guest has no network access with NAT and OS X refused the connection, as you can see). I'd love a general solution that would let me communicate with my guest at a fixed IP.

  Read the article

• What are the advantages of OSPF vs nexthop self with iBGP?

  - by Matt Hamilton

  Assuming I have a fairly small network internally, but I have 4 routers each connected out to a different network. The routers are all sat next to each other connected via a switch. Each router uses BGP to speak to the outside networks. There is an iBGP mesh for each router to exchange the routes internally it knows about from each external network. The usual setup is to use OSPF to distribute the connected routes, as the routes via iBGP will still have the next hop set to their original value. What is the advantage of using OSPF in this scenario versus simply using 'set nexthop self' on the routes?

  Read the article

• ip routing policy in linux

  - by Dragos

  I have a linux system with two network interfaces (eth0 in x.x.x.0 and eth1 in x.x.y.0). Is there any posibility to add some route policy to send all the traffic to network x.x.y.0. I would like even the traffic from eth0 to be send to eth1's network. I cannot delete the direct connected networks from the routing table so all the traffic from x.x.x.0 network is send to eth0. I would like to send all traffic to eth1.

  Read the article

• Virtualizing Firewalls/UTM

  - by TheD

  So Sophos UTM (Astaro Gateway UTM) can be virtualized in Hyper-V, VMWare, vSphere etc. Now I'm new to virtualization, so am wondering how the networking would be configured in this situation. Imagine the following (a very simple setup). A Zyxel router acting as the default gateway, standard ADSL line. This is connected directly via Ethernet to my VHost, Hyper-V in my case. Now I assume I need two virtual network adapters, one which is the "External" interface to the firewall, and the other being the "Internal" interface. But where does my switch go, since I have 5 machines (or X number of machines). Where is the switch connected, to the internal interface on the VHost? What default gateway do my clients use etc? How would the routing work if these two interfaces weren't bridged since they are virtual networks anyway. I'm a little confused! Any advice is much appreciated! Cheers

  Read the article

• Belkin Wireless G router not working on Windows 7

  - by coore

  I have a Belkin F5D7230-4 Wireless G router which used to work on XP. I have a clean Windows 7 install (on the same desktop PC), and it just won't work. Device Manager lists the adapter as a USB device, but it says "The drivers for this device are not installed", even though the driver installer said the installation was OK. Manage Wiresless Networks says "wireless is not currently enabled". The WLAN AutoConfig service is running. My specific question is which of the two symptoms above should I go for first? Should I try to fix the driver installation somehow, or should I try to enable wireless? Is one caused by the other, or is this two independent problems? Any other thoughs that could help me are also appreciated.

  Read the article

• Problems connecting Centos on VMware to the network using bridged connection.

  - by Sakin

  Hi, I installed CentOs on VMware running on windows XP. When trying to configure it to connect to the internet in a bridged configuration, I get an error message when trying to bring up the network interface: [root@VMLinux ~]# /et/init.d/network start Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... failed [FAILED] VM is running on a machine that has access to the network, I tried it on two different networks that have DHCP enabled. Everything works fine when using a NAT connection through my host. How can I make the bridge work for me? Thanks.

  Read the article

• How to restrict access to a specific wireless network to only 1 user profile in Windows 7.

  - by Mathlight

  Hi all, I'm using Win7 SP1. I've got multiple users on the laptop that can / must connect to a wireless network, lets call it Wireless1. I've got an second wireless network, (lets call it Wireless2), which I want to limit access to only the admin user of the laptop. Now I can remove Wireless2 in the network manager every time, but i want a more user friendly solution, so that only the admin can connect to Wireless2, and all the other users cannot ( they may see the network, but must enter the password, like all other networks ). Any ideas?

  Read the article

• Server problem (duh)

  - by j-t-s

  Sorry the title couldn't be more specific. I installed Abyss Web Server. I'm running Windows XP Home Edition and I have Wireless Mobile Broadband internet. I used to be able to access (and other people on other networks) my site by entering my ip address in the browser, but after I formatted, and the installed abyss web server again, this does not work anymore. There are no errors. I CAN visit my own site by entering my ip address BUT anybody else can't do the same, it just says "connecting" in the browser's statusbar and it never changes. I have consulted the docs and have found no help. Google hasn't helped with this problem either. Can somebody please help? Thank you :)

  Read the article

• Server problem (duh)

  - by j-t-s

  Sorry the title couldn't be more specific. I installed Abyss Web Server. I'm running Windows XP Home Edition and I have Wireless Mobile Broadband internet. I used to be able to access (and other people on other networks) my site by entering my ip address in the browser, but after I formatted, and the installed abyss web server again, this does not work anymore. There are no errors. I CAN visit my own site by entering my ip address BUT anybody else can't do the same, it just says "connecting" in the browser's statusbar and it never changes. I have consulted the docs and have found no help. Google hasn't helped with this problem either. Can somebody please help? Thank you :)

  Read the article

• Ubuntu (11.10) fails to connect to wireless network

  - by Tal Galili

  I just installed ubuntu 11.10, and tried to have it connect to the internet. I use a wireless USB stick by edimax (it is called IEEE802.11b/g/n nano USB adapter or also EW-7811Un). My problem is that Ubuntu seems to be able to use the USB to see the networks around me, but when I try to connect to my network - it just keeps trying and failing. I am connected to the internet through a 300M Wireless N Router Model No. TL-WR841N / TL-WR841ND Can you please advise on how this can be resolved? Thanks!

  Read the article

• Sharing internet through a wireless ad-hoc in Windows 7

  - by vzait

  I'm actually requesting a workaround to share a PPoE wired Internet connection between two laptops using wireless. I've tried sharing it the usual way... New Ad-hoc = Click turn On sharing = etc. I've tried changing all the settings I could find related to the two networks on both machines. Conclusion: Sometimes it works, sometimes it doesn't. Is it really buggy, or are my hands growing from the wrong place? I'm almost sure I'm not the only one having this kind of problem. What is the easiest/correct workaround ?

  Read the article

• How to disable color dithering for low-bit-depth screen settings?

  - by gogowitsch

  I am using Terminal Services and TeamViewer a lot to access other computers, partly over slow networks. The problem described below is not affected by which of the two remote access services I am using. When accessing Windows 7 Professional machines, a great deal of text is hard to read as the background is dithered. Even for exactly the same colors, Windows 2003 does not seem to dither at all, but to choose the closest available color. I strongly prefer the latter, as I don't care for the exact colors, I just want to be able to read easily. I am not sure whether this is operating system-related. The programs on the remote systems do not allow me to change the color choices for the various backgrounds to anything sane. Is there a way to disable this color dithering using some target operating system setting that will do the trick for both Terminal Services and TeamViewer?

  Read the article

• Network Role based routing

  - by Steve Butler

  Apologies my networking skills are a tad rusty. I'm looking for a way to setup a system that gives me the ability to setup Role-based access to specific network resources. For example, i have three private subnets for specific groups, users will need access to one one or more subnets. I'd like to have all client machines on the same subnet/vlan, and then use 802.1x to authorize into a router(NAC device/whatever), the router would then see what user had authenticated(huge plus if it could determine AD group), and then allow routing to one or more of the three private subnets based upon their group membership. I've looked at packetFence, and it appears to work by assigning a client to a VLAN, but i'd still need a way to route some users into different back-end networks.

  Read the article

• 8 Character Device names

  - by Lee Harrison

  Is there any reason to still use only 8 characters in a device name? My boss still uses this rule for printers, computers, routers, servers... basicly any device connected to our network. This leads to massive confusion among users, especially when it comes to printer. It also leads to confusion from an administration standpoint because every device is named vaguely, and similarly(its only 8 characters!). I understand the history behind this and compatibility with older systems, but none of our legacy systems will ever make use of PS-printers and Wifi networks. Is there any reason to still do this, and what is everyone else doing when it comes to naming network devices at an enterprise level?

  Read the article

• unable to connect to remote sql server from SHDSL router

  - by user529265

  Got a new leased line network to our office that came with a SHDSL router (Watson). Currently, we are unable to use Sql Server management studio to connect to remote Sql databases. It errors out saying A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: TCP Provider, error: 0 - The specified network name is no longer available.) (Microsoft SQL Server, Error: 64) I logged into the Watson management panel and unblocked all the ports for TCP traffic (specified the range as 0 to 60000 and UDP as well - this include 1443 required for connecting to SQL Server). The router is the only thing that has changed. We are able to connect to it from other networks just fine. Is there something we are missing here. Any help would be greatly appreciated.

  Read the article

• Text template or tool for documentation of computer configurations

  - by mjustin

  I regularly write and update technical documentation which will be used to set up a new virtual machine, or to have a lookup for system dependencies in networks with around 20-50 (server-side) computers. At the moment I use OpenOffice Writer with text tables, and create one document per intranet domain. To improve this documentation, I would like to collect some examples to identify areas where my documents can be improved, regarding general structure and content, to make it easy to read and use not only for me but also for technical staff, helpdesk etc. Are there simple text templates (for example for OpenOffice Writer) or tools (maybe database-driven) for structured documentation of a computer configuration? Such a template / tool should provide required and optional configuration sections, like 'operating system', 'installed services', 'mapped network drives', 'scheduled tasks', 'remote servers', 'logon user account', 'firewall settings', 'hard disk size' ... It is not so much low-level hardware docs but more infrastructure / integration information in these documents (no BIOS settings, MAC addresses).

  Read the article

• how to design network for connectivity between private and corporate LANs?

  - by maruti

  there is a bunch of servers connected to shared storage in a private LAN (10.x.x.x). this privateLAN is managed by a windows server (DHCP, DNS and directory services) these hosts need to be from outside of the datacenter Eg. Remote desktop. can the NIC2 on each of the hosts be connected to the other public LAN (compromising speed or security? what are improtant considerations: additional hardware? like switches? routing&DNS software? currently available hardware : Dell Powerconnect 6224 switch .... planning this for storage network. software: windows 2003 server for DHCP, DNS, A/D ? would it be more flexible to use Linux distributions like IPCOP, Untangle etc? all that I am looking for is good isolation between private and other networks, avoid DHCP, DNS, AD clashes.

  Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >