Search Results

Search found 20360 results on 815 pages for 'capture output'.

Page 450/815 | < Previous Page | 446 447 448 449 450 451 452 453 454 455 456 457  | Next Page >

• CARP: two machines think they're the master, but only on one interface

  - by Conor McDermottroe

  I have two machines, each configured identically as a firewall/load balancer for a busy website. I have set them up with CARP and pfsync on both the internal and external interfaces. The internal interface is behaving as expected (primary listed as MASTER and secondary listed as BACKUP) On both machines, the network interfaces are as follows: em0 - External interface bge0 - Internal interface bge1 - Crossover connection between both machines carp0 - Shared external interface for CARP carp1 - Shared internal interface for CARP I've rewritten the IP addresses and MAC addresses below. The networks are as follows: 10.0.1.0/24 - External network 10.0.2.0/24 - Internal network 10.0.3.0/24 - Crossover network Here's the output from ifconfig on the primary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.10 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.10 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.10 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.11 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 0 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: MASTER vhid 2 advbase 1 advskew 0 And here's the /etc/rc.conf excerpt from the primary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.10 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.11" And here's the output on the secondary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.11 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.11 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.11 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.10 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 20 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: BACKUP vhid 2 advbase 1 advskew 20 And here's the /etc/rc.conf excerpt from the secondary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.11 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] advskew 20 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] advskew 20 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.10" What I don't understand is, the carp status on carp0 is MASTER on both machines when the status on carp1 is as it should be (MASTER on the primary and BACKUP on the secondary). What am I missing? Where should I be looking for clues?

  Read the article

• Tool to check if XML is valid in my VS2012 comments

  - by davidjr

  I am writing the documentation for our companies software developed with vs2012. I need to add xml examples to the summary of each class, due to xml instantiation of objects. We are using sandcastle to create the documentation (company choice), and I want to be able to review my xml comments without building the help file every time. Is there an application that anyone would recommend where I can view how the xml renders before I build the help file? Here is my example: /// <summary> /// Performs DFT on a data array, writes output in a CSV file. /// </summary> /// <example> /// <para>XML declaration</para> /// <code lang="xml" xml:space="preserve"> /// %lt;DataProvider name="DftDP" description="Computes DFT" etc... I want to check the XML to make sure it is valid, maybe by copy and pasting it into a tool of some sort?

  Read the article

• Ubuntu server very slow out of the blue sky (Rails, passenger, nginx)

  - by snitko

  I run Ubuntu server 8.04 on Linode with multiple Rails apps under Passenger + nginx. Today I've noticed it takes quite a lot of time to load a page (5-10 secs). And it's not only websites, ssh seems to be affected too. Having no clue why this may be happening, I started to check different things. I checked how the log files are rotated, I checked if there's enough free disk space and memory. I also checked IO rate, here's the output: $ iostat avg-cpu: %user %nice %system %iowait %steal %idle 0.17 0.00 0.02 0.57 0.16 99.07 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvda 2.25 39.50 16.08 147042 59856 xvdb 0.00 0.05 0.00 192 0 xvdc 2.20 25.93 24.93 96530 92808 xvdd 0.01 0.12 0.00 434 16 xvde 0.04 0.23 0.35 858 1304 xvdf 0.37 0.31 4.12 1162 15352 Rebooting didn't help either. Any ideas where should I be looking?

  Read the article

• CodePlex Daily Summary for Monday, October 24, 2011

  CodePlex Daily Summary for Monday, October 24, 2011Popular ReleasesPeople's Note: People's Note 0.31: Added note tag editing. Changed note edit conflict resolution to keep the latest version. To install: copy the appropriate CAB file onto your WM device and run it.Windows Azure Toolkit for Windows Phone: Windows Azure Toolkit for Windows Phone v1.3.1: Upgraded Windows Azure projects to Windows Azure Tools for Microsoft Visual Studio 2010 1.5 – September 2011 Upgraded the tools tools to support the Windows Phone Developer Tools RTW Update SQL Azure only scenarios to use ASP.NET Universal Providers (through the System.Web.Providers v1.0.1 NuGet package) Changed Shared Access Signature service interface to support more operations Refactored Blobs API to have a similar interface and usage to that provided by the Windows Azure SDK Stor...Workflow Automation (for Dynamics CRM 2011): Release 1.0: Initial release version 1.0.Window Manipulation with the Microsoft Touch Mouse: Window Touch v1.0: This is the initial release of the Window Touch software, which may have bugs and incomplete interactions. Please be patient with us as we work out all of the kinks, and feel free to send comments. To install and run the program download and double click the .msi file below. Make sure you already have a Microsoft Touch Mouse and can use it before installing.xUnit.net Contrib: xunitcontrib-resharper 0.4.4 (dotCover): xunitcontrib release 0.4.4 (ReSharper runner) This release provides a test runner plugin for Resharper 6.0 RTM, targetting all versions of xUnit.net. (See the xUnit.net project to download xUnit.net itself.) This release addresses the following issues:Support for dotCover code coverage 4132 Note that this build work against ALL VERSIONS of xunit. The files are compiled against xunit.dll 1.8 - DO NOT REPLACE THIS FILE. Thanks to xunit's version independent runner system, this package can r...BookShop: BookShop: BookShop WP7 clientRibbon Editor for Microsoft Dynamics CRM 2011: Ribbon Editor (0.1.2122.266): Added CodePlex and PayPal links New icon Bug fix: can't connect to an IFD deployment when the discovery service url has been customizedSiteMap Editor for Microsoft Dynamics CRM 2011: SiteMap Editor (1.0.921.340): Added CodePlex and PayPal links New iconMVCQuick: MVCQuick 0.3.1: Features??NHibernate 3.2??Repository（ORuM） ??Spring.Net 1.3.2??Container（IoC） ??Common.Logging 1.2??Logging ASP.NET Security Provider?? ??MVCQuick.Framework??MusicStoreDotNet.Framework.Common: DotNet.Framework.Common 4.0: ??????????，????????????XML Explorer: XML Explorer 4.0.5: Changes in 4.0.5: Added 'Copy Attribute XPath to Address Bar' feature. Added methods for decoding node text and value from Base64 encoded strings, and copying them to the clipboard. Added 'ChildNodeDefinitions' to the options, which allows for easier navigation of parent-child and ID-IDREF relationships. Discovery happens on-demand, as nodes are expanded and child nodes are added. Nodes can now have 'virtual' child nodes, defined by an xpath to select an identifier (usually relative to ...Media Companion: MC 3.419b Weekly: A couple of minor bug fixes, but the important fix in this release is to tackle the extremely long load times for users with large TV collections (issue #130). A note has been provided by developer Playos: "One final note, you will have to suffer one final long load and then it should be fixed... alternatively you can delete the TvCache.xml and rebuild your library... The fix was to include the file extension so it doesn't have to look for the video file (checking to see if a file exists is a...CODE Framework: 4.0.11021.0: This build adds a lot of our WPF components, including our MVVC and MVC components as well as a "Metro" and "Battleship" style.GridLibre para Visual FoxPro: GridLibre para Visual FoxPro v3.5: GridLibre Para Visual FoxPro: esta herramienta ayudara a los usuarios y programadores en los manejos de los datos, como Filtrar, multiseleccion y el autoformato a las columnas como la asignacion del controlsource.Umbraco CMS: Umbraco 5.0 CMS Alpha 3: Umbraco 5 Alpha 3Umbraco 5 (aka Jupiter) will be the next version of everyone's favourite, friendly ASP.NET CMS that already powers over 100,000 websites worldwide. Try out the Alpha of v5 today! If you're new to Umbraco and would like to get a low-down on our popular and easy-to-learn approach to content management, check out our intro video. What's Alpha 3?This is our third Alpha release. It's intended for developers looking to become familiar with the codebase & architecture, or for thos...Vkontakte WP: Vkontakte: source codeWay2Sms Applications for Android, Desktop/Laptop & Java enabled phones: Way2SMS Desktop App v2.0: 1. Fixed issue with sending messages due to changes to Way2Sms site 2. Updated the character limit to 160 from 140GART - Geo Augmented Reality Toolkit: 1.0.1: About Release 1.0.1 Release 1.0.1 is a service release that addresses several issues and improves performance. As always, check the Documentation tab for instructions on how to get started. If you don't have the Windows Phone SDK yet, grab it here. Breaking Change Please note: There is a breaking change in this release. As noted below, the WorldCalculationMode property of ARItem has been replaced by a user-definable function. ARItem is now automatically wired up with a function that perform...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.32: Fix for issue #16710 - string literals in "constant literal operations" which contain ASP.NET substitutions should not be considered "constant." Move the JS1284 error (Misplaced Function Declaration) so it only fires when in strict mode. I got a couple complaints that people didn't like that error popping up in their existing code when they could verify that the location of that function, although not strict JS, still functions as expected cross-browser.Naked Objects: Naked Objects Release 4.0.110.0: Corresponds to the packaged version 4.0.110.0 available via NuGet. Please note that the easiest way to install and run the Naked Objects Framework is via the NuGet package manager: just search the Official NuGet Package Source for 'nakedobjects'. It is only necessary to download the source code (from here) if you wish to modify or re-build the framework yourself. If you do wish to re-build the framework, consul the file HowToBuild.txt in the release. Documentation Please note that after ...New Projects360zebra4en: 360zebra???AG: Web Framework that can leverage silverlight, but fall back on native html if silverlight is not available.BookShop: BookShop ????? ???? ? ????????????? ?????????.CompendiumImport: Import data from Dungeons & Dragons Compendium to Masterplan librariesCS 6235 Arbiter Server: CS 6235 Arbiter ServerDual numbers for automatic differentiation: Dual numbers can be used to automatically calculate numerically stable derivatives of functions.Effort - Entity Framework Unit Testing Tool: Effort is a powerful unit testing tool that brings an easy way to create unit tests for Entity Framework based applications. It can manipulate the behavior of EntityConnection or ObjectContext objects, so that the data operations are executed by a fake in-process database, while omitting the real database completely. This mechanism makes possible to remove the dependency between your unit test and the real database.FlexiCache for ASP.NET applications: This library provides extended cache capabilities to the ASP.NET applications. It includes the MongoDB and SQL Server output cache providers extending ASP.NET Output Cache capabilities by allowing to store cached data outside of the application process that is especially important in web-farm scenario. This library provides "Session-On-Demand" functionality - ability to separate ASP.NET Session data to subsets that can be stored outside of the main ASP.NET session and loaded on demand w...HtmlAgilityPackContrib - Logical extension to HtmlAgilityPack: HtmlAgilityPackContrib - A logical extension to HtmlAgilityPack to parse HTML using jQuery like methods inspired by jSoupjsonhttphandler: The JsonHttpHandler is a simple JSON oriented Http handler to easily integrate JSON GET, POST, and JSONP web services into your application.My Recent Documents: This Webpart for Sharepoint 2010 is developed for users that need help finding the last number of documents they have been working on. The target user have trouble location where he/she placed their documents. This Webpart gives the following features... 1. Locate your last edited documents.. 2. Customize how many documents the webpart should find. 3. Should it look in subsites also? 4. Show the structure in where the documents are located and click easy link to either document lib...Option pricing for arbitrary distributions: European option pricing with arbitrary distributions using dual numbers to calculate greeks.Project Tracy: ????????？ ????????？ ????????10??????？ ???????????????????????。。。。。 ???！Tracy?????????????！（?RegSharp: RegSharp provides server functionality for Sencha Extjs (http://www.sencha.com/products/extjs/) paging grid. RegSharp implements sorting, filtering and paging logic on the server side that is required for using the paging grid. Is't developed in C#SharePoint/TFS Continuous Integration Starter Pack: Provides a customized TFS Build workflow and PowerShell scripts to get started with Continuous Integration (automated builds) in SharePoint 2010/TFS 2010. This pack will allow you to automatically build and deploy WSPs using TFS, and optionally also include automated testing as part of the build such as Visual Studio 2010's Coded UI Tests. Sharp Investor: Sharp Investor pools various online sources as well as preforms a couple local calculation to return recommended stocks. The program is easy to use, and requires very little work to find profitable stocks online. It's developed in C#.SharpXML: Aims to be a simpler library for interacting with XML files that exposes attributes and children elements as properties and objects respectively.Splash: Splash is an interactive MediaCenter-style YouTube client written in WPF.TomCdc: TomCdc is a solution which makes tracking of sql databse changes easy. Quick and simple installation process allows to start using the solution in just a few minutes. It supports all versions of Microsoft Sql server. You'll no longer have to write triggers manually to find out what process is changing data in a table.Track your work: Another work-time tracker TumblePower: TumblePower is a simplified API library for Tumblr. Use it in your application to post Text, Photos, Quotes, Links, Chats, Audio and Videos as well as set functions such as tags, dates and choose whether the post should be private or not.VisualBASH: This project aims to extends Visual Studio's language support to include bash scripting. This includes syntax highlighting, code completion, and syntax error checking.Window Manipulation with the Microsoft Touch Mouse: Window Manipulation for the Microsoft Touch Mouse provides a set of simple gestures for moving and resizing windows.Workflow Automation (for Dynamics CRM 2011): Workflow Automation for Dynamics CRM 2011 allows user to automate or schedule workflow execution via Windows Task Scheduler. XNA Model Viewer: The XNA Model Viewer allows you to load FBX files and view them. It allows you to test that models will work in XNA, determine the effect of modifying bone transforms, and view animation clips. You can examine the bones and meshes and see the complete hierarchy.

  Read the article

• What extra packages are needed by Amarok to transcode to MP3?

  - by Jon Pawley

  I'm using Amarok 2.6.0, on KDE version 4.9.3, on Kubuntu 12.04. I would like to be able to copy my music onto my MP3 player (in this case, my iPhone 3), but to transcode the tracks as I copy them over. However, when I right-click on the selected track, and choose "Copy to Collection" and select my iPhone, the option to transcode to MP3 is greyed out. What additional packages does Amarok need in order to enable the transcode to MP3 option? Thanks, Jon Oh, the "Amarok DIagnostics" output, from the Help menu gives: Amarok Diagnostics Amarok Version: 2.6.0 KDE Version: 4.9.3 Qt Version: 4.8.2 Phonon Version: 4.6.0 Phonon Backend: GStreamer (4.6.2) PulseAudio: Yes Amarok Scripts: Amarok Script Console 1.0 (stopped) Discogs 1.1b (stopped) Lyricwiki .2 (stopped) Free Music Charts 1.6.0 (stopped) Librivox.org 1.0 (stopped) Cool Streams 1.0 (stopped) BBC 1.1 (stopped) Amarok Plugins: AudioCd Collection (enabled) DAAP Collection (enabled) MTP Collection (enabled) MySQLServer Collection (enabled) MySQLe Collection (enabled) UPnP Collection (enabled) Universal Mass Storage Collection (enabled) iPod, iPad & iPhone Collection (enabled) Ampache (disabled) Jamendo (disabled) Last.fm (enabled) MP3 Music Store (disabled) MP3tunes (disabled) Magnatune Store (disabled) Podcast Directory (enabled) gpodder.net (enabled) Local Files & USB Mass Storage Backend (enabled) NFS Share Backend (enabled) SMB (Windows) Share Backend (enabled)

  Read the article

• Failed to import SLES11 to SCOM2012

  - by siyang

  I try to the import my SLES11 to SCOM 2012, but failed. Below is my simple steps and failed error message. Import SLES11 mp DNS resolve both SCOM and SLES11 Install SCOM Agent and cert. Generated the cert from SLES11 then import it to SCOM, and use scxcertconfig -sign to refresh the cert, and back it to SLES11.(I restart the scxadmin on SLES11, and reboot the SCOM ) 5. On SCOM try to find the SLES11, but failed. Below is the error message. *Message: Certificate signing was not successful. Detials: Standard Output: Failed to start child process '/etc/init.d/scx-cimd' errno=13RETURN CODE:1 Standard Error: Exception Message:*

  Read the article

• How atomic is a SELECT INTO?

  - by leo.pasta

  Last week I got an interesting situation that prompted me to challenge a long standing assumption. I always thought that a SELECT INTO was an atomic statement, i.e. it would either complete successfully or the table would not be created. So I got very surprised when, after a “select into” query was chosen as a deadlock victim, the next execution (as the app would handle the deadlock and retry) would fail with: Msg 2714, Level 16, State 6, Line 1 There is already an object named '#test' in the database. The only hypothesis we could come up was that the “create table” part of the statement was committed independently from the actual “insert”. We can confirm that by capturing the “Transaction Log” event on Profiler (filtering by SPID0). The result is that when we run: SELECT * INTO #results FROM master.sys.objects we get the following output on Profiler: It is easy to see the two independent transactions. Although this behaviour was a surprise to me, it is very easy to workaround it if you feel the need (as we did in this case). You can either change it into independent “CREATE TABLE / INSERT SELECT” or you can enclose the SELECT INTO in an explicit transaction: SET XACT_ABORT ON BEGIN TRANSACTION SELECT * INTO #results FROM master.sys.objects COMMIT

  Read the article

• How to run installation CD for second monitor?

  - by dobsoft

  I am running ubuntu 14 off of a live USB. I have a second monitor that I would like to use while using ubuntu. It has an installation cd that you have to install before using, and when I click on the .exe file the Archive Manager tries to open it and says an error occurred while loading the archive. Thanks for the help. Edit: additional information It just doesn't show up when when I'm in the display settings area. I press the locate(name is probably something else) monitor button too. I know it needs the CD because when I was using it with Windows it didn't work until I went through the installation process on the CD. If ubuntu doesn't use .exe files is there a way to use the CD still? Monitor info from label: -acer LCD monitor -model number: S200HQL Version: S200HQL bd I connect it to my computer using a VGA cord which is connected to a j5create VGA to USB adapter. Not sure if this helps: VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) lsusb output: Bus 002 Device 004: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 002 Device 005: ID 0bc2:2100 Seagate RSS LLC Bus 002 Device 007: ID 0711:5200 Magic Control Technology Corp. Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 1bcf:2c18 Sunplus Innovation Technology Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Configuring NAT and static IP on Cisco 877W

  - by David M Williams

  Hi all, I'm having trouble setting up a static IP reservation on a network. What I want to do is assign IP 192.168.1.105 to MAC address 00:21:5d:2f:58:04 and then port forward 35394 to it. If it helps, output from show ver says Cisco IOS software, C870 software (C870-ADVSECURITYK9-M), version 12.4(4)T7, release software (fc1) ROM: System bootstrap, version 12.3(8r)YI4, release software I have done this - service dhcp ip routing ip dhcp excluded-address 192.168.1.1 192.168.1.99 ip dhcp excluded-address 192.168.1.200 192.168.1.255 ip dhcp pool ClientDHCP network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 192.168.1.1 lease 7 ip dhcp pool NEO host 192.168.1.105 255.255.255.0 hardware-address 0021.5D2F.5804 ip nat inside source static tcp 192.168.1.105 35394 <PUBLIC_IP> 35394 extendable However, the machine is getting assigned IP address 192.168.1.101 not .105 ... any suggestions? Thanks !

  Read the article

• Mapping a Piped Shell Command in Vim

  - by michaelmichael

  In a previous question I asked about mapping evaluated code to a new window in MacVim. I got a great solution, but it presented another question: How can I map a key command in my .vimrc that involves piping output in the shell? As a simple example, let's say I wanted to pipe the results of ls -a to a new MacVim window. From the Vim command line I can enter !ls -a | mvim -, and the results will appear in a new window. Great! Now, I add that to my .vimrc: nmap <Leader>r :w !ls | mvim<CR> Vim now throws an error every time I try to source my .vimrc, which reads as follows: E492: Not an editor command: mvim<CR> Any ideas on how to overcome this?

  Read the article

• Pressing an accent key (´ / ?) adds the character twice in most programs

  - by sh code

  This might seem as duplicate of Pressing key with accent character makes it enter twice but it is not: About three days ago, the issue started - I am using Slovak (Slovakia) keyboard, and the key for adding accents/diacritics (just left from backspace) acts strangely - it should "do nothing" upon pressing, and then when character key is pressed right after it, it should output that character with accent/diacritics. However, in most programs, pressing it once results in immediately outputting the accent itself twice (which under normal circumstances happens when you press the key twice). This issue doesn't happen in Visual Studio or any program I make in it, and Pidgin, it seems to happen everywhere else (firefox, notepad, MS OneNote, Windows Explorer itself). I am not aware of any software installations, driver changes or system updates between the time it worked properly and the time when it broke. What could be the problem and how do I solve it?

  Read the article

• Need a PCIe desktop graphics card for dual-monitor

  - by Graham

  I have a mid-2008 workstation with two HD monitors supporting HDMI and DVI inputs. Since Ubuntu 11.10, I have experienced no end of trouble with my NVidia Quadro NVS 290 in TwinView dual-monitor output. Others have similar desktop TwinView woes. I want a new graphics card. Previously I asked for a graphics card recommendation and response was Nvidia Geforce GTS 450... but really I'm looking for someone who has actually got a working dual-monitor desktop to tell me what card they use so I can get something that is known to work. So please, people who have no-issues with their 64-bit Ubuntu 12.04 Unity 3D desktop spread across two HD-resolution external monitors (either DVI or HDMI connector), and who also run Google Chrome (which throws a spanner due to its own GPU compositing)... please let me know what graphics card you have so I can buy one. Gathering Options These seem to be the Nvidia cards featuring dual DVI. But they all seem to be gaming cards - what has dual-DVI, good support, but is not a massive gaming card? Nvidia GTS 450 (previously recommended) - 2x DVI Nvidia GTX 550 Ti (used by System76) - 2x DVI Nvidia GT 430 (used by System76) - 1xDVI, 1xHDMI Nvidia GT 640 (found on NVidia site) - 1xDVI, 1xHDMI (also GT 620, GT 630) Has anyone had a good desktop dual-monitor Unity 3D experience with ATI cards?

  Read the article

• Apache RewriteRule with a RewriteMap variable substitution for the VAL argument to environment variable

  - by Eric

  I have an Apache server that serves up binary files to an application (not a browser). The application making the request wants the HTTP Content-MD5 header in HEX format. The default and only option within Apache is Base64. If I add "ContentDigest on" to my VirtualHost, I get this header in Base64. So I wrote a perl script, md5digesthex.pl, that gives me exactly what I want: MD5 in HEX format but I'm struggling with the RewriteRule to get my server to send the result. Here is my current Rewrite recipe: RewriteEngine on RewriteMap md5inhex prg:/www/download/md5digesthex.pl RewriteCond %{REQUEST_URI} ^/download/(.*) RewriteRule ^(.*) %{REQUEST_URI} [E=HASH:${md5inhex:$1}] Header set Content-MD5 "%{HASH}e" env=HASH The problem is that I can't seem to set the HASH environment variable based on the output of the md5inhex map function. It appears this behavior is not supported and I'm at a lost as to how to formulate this...

  Read the article

• Web to Print system - which client side technology should I use

  - by mr null

  I'm getting started to develop Web to Print system. My main concern is which client-side techology should I use: jQuery/CSS Flex/ActionScript or something else? For now, idea is that user/customer choose Product eg: Business card Attributes: Dimensions,Paper type, ... etc Template or blank Adjust product (editor) Preview & order Output should be PDF 300dpi. My main issue is: adding/adjusting text in editor. (font size, font family...). Because application should be cross browser. And I think that 10px Arial can't be the same in Firefox 5 and IE 8. It must be pixel perfect in every browser. If somebody order $100 of business cards, and text is different that he/she saw when ordering - that is a big problem. So, Flash platform should be the answer. But, as I see it's dying technology, 2012 is here - HTML5 is replacing Flash rapidly. I hope that you understand me, so every guideline or few smart words would be very appreciating.

  Read the article

• Nodes inside Cisco VPN. Incoming SSH requests allowed. But can't initiate an outbound SSH.

  - by Douglas Peter

  I've a gateway-to-gateway VPN setup between my Linksys RV042 router and a Cisco VPN. I am able to SSH into any of the machine inside the VPN from my network. But none of the machines inside the VPN can initiate an SSH into my network. It seems they've blocked even all ping requests to my network gateway. This is the requirement: I have scripts that SSH into the machines inside the VPN and run a long mysql query. The query generates an output to a file. The time that these queries take is variable. So I have a loop in my machine that periodically SSHes into the VPN machine and checks if the query has finished, and pulls the generated file using SCP. I need to simplify it thus: The script will run at the machine inside the VPN, and when the query completes, it will SSH into my machine and pushes the generated file. Thanks for any ideas.

  Read the article

• Sound from both speakers and headphones with SoundMAX ADI AD1986A on Windows 7: possible?

  - by oKtosiTe

  My ASUS A8N-VM CSM motherboard has an on-board sound chip–the SoundMAX ADI AD1986A. Although sound does work reliably on Windows 7, I was a bit disappointed that neither ASUS nor the manufacturer of the sound chip offer drivers for it for Windows 7 (or Vista for that matter). Among other things jack detection, output to front and read jack simultaneously and surround sound are no longer available using Microsoft's default HD Audio driver under Windows 7. Under Windows XP and several Linux distributions (Arch, Gentoo and Ubuntu) that I've tried everything works as it should. Since I switch between headphones and speakers quite often, this annoyance begs me to ask: aside from buying a sound card, is there any way to get sound from both outputs at the same time?

  Read the article

• Free Video Editing Software for windows with storyboard mode

  - by The Journeyman geek

  My dad's currently using windows movie maker to try to make a video out of a series of JPEG images and some MP3s. He's not very happy with it, since Windows movie maker seems to downsample the source images he's used, and not very efficently - despite them being the same resolution as the output WMM is supposed to make, and the replaygain based audio level normalisation on the tracks don't work. So, i'd want a free programme that has storyboard mode (else i'd use visualdub) that'll not try to change the resolution of images used to make a video (assuming all images are the same resolution), and preferably accept the normalised mp3 files we're using. WMM isn't a option, since Its what i'm trying to find a replacement for.

  Read the article

• D key not working on Ubuntu

  - by Jonathan

  For some inexplicable reason the capital d key on my Ubuntu system is no longer producing output. Hitting caps lock and then d produces a D. I've tried multiple keyboards and the issue is the same. There's nothing bound to Shift+d under System Preferences Keyboard Shortcuts. xev produces the following: shift + a KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31268952, (130,-16), root:(1000,525), state 0x10, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269376, (130,-16), root:(1000,525), state 0x11, keycode 38 (keysym 0x41, A), same_screen YES, XLookupString gives 1 bytes: (41) "A" XmbLookupString gives 1 bytes: (41) "A" XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269584, (130,-16), root:(1000,525), state 0x11, keycode 38 (keysym 0x41, A), same_screen YES, XLookupString gives 1 bytes: (41) "A" XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269608, (130,-16), root:(1000,525), state 0x11, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False shift + d KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31102792, (115,-13), root:(985,528), state 0x10, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False FocusOut event, serial 36, synthetic NO, window 0x4c00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 36, synthetic NO, window 0x4c00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 36, synthetic NO, window 0x0, keys: 2 0 0 0 0 0 0 64 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31103104, (115,-13), root:(985,528), state 0x11, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

  Read the article

• [SOLVED]Another version of this product is already installed. Installation of this version cannot continue. To configure or remove the existing version of this product, use Add/Remove Programs on the Control Panel

  - by kazim sardar mehdi

  Another version of this product is already installed.  Installation of this version cannot continue.  To configure or remove the existing version of this product, use Add/Remove Programs on the Control Panel I tried to install a new version of windows services that packed into 1 setup.msi and encounter the above mentioned error. To resolve it I tried google read lots of but then find the following article MSIEXEC - The power user's install steps to solve the error: 1. Execute the following command from command prompt: msiexec /i program_name.msi /lv logfile.log where program_name.msi is the new version /lv is log Verbose output   2. open up the logfile.log in the editor 3. find the GUID in it I found it like the following Product Code from property table before transforms: '{GUID}' 4. Above mentioned article suggest  to search it in the registry but to find the uninstall command. Try if you like to see it in the registry. you need to search twice to to get there there you I tried the following command as it mentioned in the above mentioned article but it didn’t work for me. so I keep digging until I got Windows 7 and Windows Installer Error “Another installation is in progress” It mentioned the use of msizap.exe 5.   by combining the commands from both the articles I able to uninstall the service successfully execute the following command from the visual studio command prompt if you already have installed or get it from Microsoft website http://msdn.microsoft.com/en-us/library/aa370523%28VS.85%29.aspx   msizap.exe TWP {GUID} it did the trick and removed the installed service successfully

  Read the article

• CodeGolf : Find the Unique Paths

  - by st0le

  Here's a pretty simple idea, in this pastebin I've posted some pair of numbers. These represent Nodes of a unidirected connected graph. The input to stdin will be of the form, (they'll be numbers, i'll be using an example here) c d q r a b d e p q so x y means x is connected to y (not viceversa) There are 2 paths in that example. a->b->c->d->e and p->q->r. You need to print all the unique paths from that graph The output should be of the format a->b->c->d->e p->q->r Notes You can assume the numbers are chosen such that one path doesn't intersect the other (one node belongs to one path) The pairs are in random order. They are more than 1 paths, they can be of different lengths. All numbers are less than 1000. If you need more details, please leave a comment. I'll amend as required. Shameless-Plug For those who enjoy Codegolf, please Commit at Area51 for its very own site:) (for those who don't enjoy it, please support it as well, so we'll stay out of your way...)

  Read the article

• Execute a SSIS package in Sync or Async mode from SQL Server 2012

  - by Davide Mauri

  Today I had to schedule a package stored in the shiny new SSIS Catalog store that can be enabled with SQL Server 2012. (http://msdn.microsoft.com/en-us/library/hh479588(v=SQL.110).aspx) Once your packages are stored here, they will be executed using the new stored procedures created for this purpose. This is the script that will get executed if you try to execute your packages right from management studio or through a SQL Server Agent job, will be similar to the following: Declare @execution_id bigint EXEC [SSISDB].[catalog].[create_execution] @package_name='my_package.dtsx', @execution_id=@execution_id OUTPUT, @folder_name=N'BI', @project_name=N'DWH', @use32bitruntime=False, @reference_id=Null Select @execution_id DECLARE @var0 smallint = 1 EXEC [SSISDB].[catalog].[set_execution_parameter_value] @execution_id,  @object_type=50, @parameter_name=N'LOGGING_LEVEL', @parameter_value=@var0 DECLARE @var1 bit = 0 EXEC [SSISDB].[catalog].[set_execution_parameter_value] @execution_id,  @object_type=50, @parameter_name=N'DUMP_ON_ERROR', @parameter_value=@var1 EXEC [SSISDB].[catalog].[start_execution] @execution_id GO The problem here is that the procedure will simply start the execution of the package and will return as soon as the package as been started…thus giving you the opportunity to execute packages asynchrously from your T-SQL code. This is just *great*, but what happens if I what to execute a package and WAIT for it to finish (and thus having a synchronous execution of it)? You have to be sure that you add the “SYNCHRONIZED” parameter to the package execution. Before the start_execution procedure: exec [SSISDB].[catalog].[set_execution_parameter_value] @execution_id,  @object_type=50, @parameter_name=N'SYNCHRONIZED', @parameter_value=1 And that’s it . PS From the RC0, the SYNCHRONIZED parameter is automatically added each time you schedule a package execution through the SQL Server Agent. If you’re using an external scheduler, just keep this post in mind .

  Read the article

• Use linefeed or carriage return in Subversion commit message from the command line

  - by Scott

  I am using Subversion 1.6.6 on Ubuntu 10.04. I would like to insert a carriage return, or linefeed, or newline into my commit message so that when reading the log, the comments are formatted appropriately. It works fine when I use the system editor, or specify a file for the commit comment, but what I really want is to be able to do something like the following: svn ci -m "This is the first line\nThis is the second line" and have the comment presented as: This is the first line This is the second line My example does not work, it produces output: This is the first line\nThis is the second line So, is there a way to do this? If so, how?

  Read the article

• Blank screen after Switch User or Resume

  - by matt wilkie

  About half the time when I switch users or resume from standby or resume the screen goes blank (black). If I work the cursor keys I can hear the system bell when it gets to the end of the user list. I can also successfully login, going from memory, but screen stays black. Sometimes closing and re-opening the lid will light up the screen again. Pressing the special Function key to enable/disable external monitor connection has no effect [Fn]-[F5],[Fn]-[F6]. If none of the previous work I need to put the computer into hibernation or full power off to restore screen function. If I watch closely when switching users I think I can see the screen initially start to light up and then quickly fade to black. The computer is an Acer Aspire 3500, model ZL6, running Ubuntu 10.10 installed 2 days ago. No proprietary drivers are in use. I'll provide a list of hardware details as soon as I can figure out how to generate that (didn't there used to be an entry for hardware details under the System menu?). Possibly related questions: No resume after Hibernate or Standby When I resume from suspension - the screen is blank Switch user fails to complete successfully For what it's worth, blank after resume also used to happen occasionally when the laptop was running XP-Home, but nowhere near as often, perhaps 6 or 8 times a year. UPDATE: I found System Administration System Testing and ran the Monitor test. It went very very dark, but the window elements could be discerned, and the whole screen flashed (from very very dark to black). On the third repeat of that same test the screen went to full blaupck and stayed there. Moving the mouse, via touchpad, or touch keys did not wake it up again. I had to close the lid and put the computer into hibernate, and press the power button to restore it. UPDATE2: output of lshw: http://pastebin.com/q7n8676r, lspci: http://pastebin.com/6ujzVK4r UPDATE3: sometimes I can restore the screen by flipping to console 1 with ctrl-alt-F1 and then back to graphical with ctrl-alt-F7.

  Read the article

• How can I hard reset a USB device?

  - by Cory

  I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on superuser.com as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

  Read the article

• How do I add and/or keep subtitles when converting video?

  - by JoeSteiger

  I have a mkv video I want to convert to mp4, but every which way I try and convert it (Handbrake, WinFF, ffmpeg, mencoder,...I lose the video's subtitles. How can I convert the video,keeping the subtitles, or add a subtitles.srt? I also would like 2 pass encoding with a video bitrate of 4054 and audio bitrate of 160. Thanks. I was asked for the ffmpeg -i: joe@joe-Leopard-Extreme:/media/Elements/Home Folder/Videos$ ffmpeg -i iron.mkv ffmpeg version 0.8.3-4:0.8.3-0ubuntu0.12.04.1, Copyright (c) 2000-2012 the Libav developers built on Jun 12 2012 16:52:09 with gcc 4.6.3 *** THIS PROGRAM IS DEPRECATED *** This program is only provided for compatibility and will be removed in a future release. Please use avconv instead. [matroska,webm @ 0x1a319a0] Estimating duration from bitrate, this may be inaccurate Input #0, matroska,webm, from 'iron.mkv': Metadata: title : Iron Duration: 02:06:01.67, start: 0.000000, bitrate: 1280 kb/s Chapter #0.0: start 0.000000, end 546.170622 Metadata: title : Chapter 00 Chapter #0.1: start 546.170622, end 1080.579489 Metadata: title : Chapter 01 Chapter #0.2: start 1080.579489, end 1609.941667 Metadata: title : Chapter 02 Chapter #0.3: start 1609.941667, end 2101.849733 Metadata: title : Chapter 03 Chapter #0.4: start 2101.849733, end 2595.259333 Metadata: title : Chapter 04 Chapter #0.5: start 2595.259333, end 3158.488667 Metadata: title : Chapter 05 Chapter #0.6: start 3158.488667, end 3564.644400 Metadata: title : Chapter 06 Chapter #0.7: start 3564.644400, end 4052.423356 Metadata: title : Chapter 07 Chapter #0.8: start 4052.423356, end 4304.300000 Metadata: title : Chapter 08 Chapter #0.9: start 4304.300000, end 4711.206489 Metadata: title : Chapter 09 Chapter #0.10: start 4711.206489, end 5080.575489 Metadata: title : Chapter 10 Chapter #0.11: start 5080.575489, end 5700.111067 Metadata: title : Chapter 11 Chapter #0.12: start 5700.111067, end 6269.346400 Metadata: title : Chapter 12 Chapter #0.13: start 6269.346400, end 6811.471333 Metadata: title : Chapter 13 Chapter #0.14: start 6811.471333, end 7561.679000 Metadata: title : Chapter 14 Stream #0.0(eng): Video: h264 (High), yuv420p, 1920x1080 [PAR 1:1 DAR 16:9], 23.98 fps, 23.98 tbr, 1k tbn, 47.95 tbc Stream #0.1(eng): Audio: ac3, 48000 Hz, 5.1, s16, 640 kb/s (default) Metadata: title : 3/2+1 Stream #0.2(ita): Audio: ac3, 48000 Hz, 5.1, s16, 640 kb/s Metadata: title : 3/2+1 Stream #0.3(eng): Subtitle: pgssub (default) Stream #0.4(eng): Subtitle: pgssub Stream #0.5(eng): Subtitle: pgssub Stream #0.6(eng): Subtitle: pgssub At least one output file must be specified joe@joe-Leopard-Extreme:/media/Elements/Home Folder/Videos

  Read the article

< Previous Page | 446 447 448 449 450 451 452 453 454 455 456 457  | Next Page >