Search Results

Search found 44090 results on 1764 pages for 'working conditions'.

Page 450/1764 | < Previous Page | 446 447 448 449 450 451 452 453 454 455 456 457 | Next Page >

Android openvpn + zeroconf browser sending mdns query packets over eth0 instead of tap0 interface on wifi

- by Mrunal

On an android device, I am connecting to a remote network using openvpn for performing service discovery. WORKING CASE: After the device is camped on 3g/4g and after connecting to remote network by openvpn, when the zeroconf browser is launched, I can see the mdns query packets being send through the tap0 interface resulting into rendering of services on the browser. From the tcpdump captured on the device, I can see that the mdns query packets are send to tap0 interface. tap0 ip: 192.168.11.200 Route table information: Destination Gateway Genmask Flags Metric Ref Use Iface 76.26.112.234 10.179.240.1 255.255.255.255 UGH 0 0 0 pdpbr1 10.179.240.1 * 255.255.255.255 UH 0 0 0 pdpbr1 32.1.72.136 * 255.255.255.255 UH 0 0 0 pdpbr0 10.179.240.0 * 255.255.255.0 U 0 0 0 pdpbr1 192.168.11.0 * 255.255.255.0 U 0 0 0 tap0 default 192.168.11.1 0.0.0.0 UG 0 0 0 tap0 NOT WORKING CASE: However, after switching on the wifi and connecting it to remote network, when the zeroconf browser is launched, instead of sending the mdns query packets to tap0 interface; these packets are being send to eth0 interface due to which we cannot see the services. From the tcpdump captured on the device, I can see that mdns query packets are send to eth0 interface. tap0 ip: 192.168.11.200 eth0 ip: 192.168.43.230 route table information: Destination Gateway Genmask Flags Metric Ref Use Iface 76.26.112.234 192.168.43.1 255.255.255.255 UGH 0 0 0 eth0 32.1.72.136 * 255.255.255.255 UH 0 0 0 pdpbr0 192.168.11.0 * 255.255.255.0 U 0 0 0 tap0 192.168.43.0 * 255.255.255.0 U 0 0 0 eth0 default 192.168.11.1 0.0.0.0 UG 0 0 0 tap0 In the above case, even though there is a default route for tap0, all the multicast packets are being routed through eth0. How is this possible? Has anyone observed a similar problem and it would be really helpful if you can help us to discover services through zeroconf browser after the device is connected to remote network via openvpn through wifi. Thank You Very much, Mrunal

Read the article
Tracking down the cause of a web service fault running in IIS

- by BG100

I have built a web service in Visual Studio 2008, and deployed it on IIS 7 running on Windows Server 2008 R2. It has been extensively tested, handles all errors gracefully and logs any uncaught errors to a file using log4net. The system normally runs perfectly, but occasionally (2 or 3 times a day) a fault occurs and screws up the application which needs an iisreset to get it working again. When the fault occurs I get some random errors that are caught by my catch-all error log, such as: Value cannot be null. Could not convert from type 'System.Boolean' to type 'System.DateTime'. Sequence contains no elements These errors are raised on every request until I manually do an iisreset, but there is no sight of them when the system is running normally. The web service is a stateless request-response application. Nothing is stored in the session. It could be load related, but I doubt it as there are only around 30 or 40 requests per minute. This is proving very tricky to track down. I can't work out what is putting IIS into this bad state, and why it needs an iisreset to get it working again. Nothing is reported in the event log. Can anyone suggest how to enable more extensive logging that might catch this fault? Also, does anyone know what might be causing the problem?

Read the article
Microsoft Application Request Routing with Windows Authentication

- by theplatz

I'm running into a problem trying to get Windows Authentication working in an environment that uses Microsoft Application Request Routing and was hoping someone might be able to help. The problem I'm running into is that only some requests are authenticated, while others fail with 401 errors. I have followed the Special Case of Running IIS 7.0 in a Web Farm instructions found at http://blogs.msdn.com/b/webtopics/archive/2009/01/19/service-principal-name-spn-checklist-for-kerberos-authentication-with-iis-7-0.aspx to no avail. My current server setup looks like the following: ARR Two servers set up with IIS shared configuration using IIS 7.5 on Windows 2008 R2 Anonymous authentication turned on for the Default Web Site Web Farm Two servers running IIS 7.5 on Windows 2008 R2 Three web sites set up using port binding to differentiate between virtual hosts. Ports being used are 8000, 8001, and 8002 Application pools for Windows Authentication all use a common domain account SPN added to domain account for http/<virthalhost-name>:<port-number> and http/<virtualhost-name>.<fully-qualified-domain>:<port-number> The IIS logs show the following when authentication is working/failing. If I understand correctly, all requests should show DOMAIN\User_Name: 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/stylesheets/techweb.landing.css - 8002 DOMAIN\User_Name ARR-HOST-1-IP-ADDRESS 200 0 0 62 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-background-right.gif - 8002 - ARR-HOST-1-IP-ADDRESS 401 2 5 0 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-background-left.gif - 8002 DOMAIN\User_Name ARR-HOST-IP-ADDRESS 200 0 0 31 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-icon.png - 8002 - ARR-HOST-1-IP-ADDRESS 401 2 5 0 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-icon.png - 8002 - ARR-HOST-1-IP-ADDRESS 401 1 2148074248 0 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/application-icon.png - 8002 - ARR-HOST-1-IP-ADDRESS 401 1 2148074248 0 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/user-background-right.gif - 8002 - ARR-HOST-1-IP-ADDRESS 401 1 3221225581 15 2012-11-19 15:03:17 CLUSTER-IP-ADDRESS GET /home/images/building.gif - 8002 DOMAIN\User_Name ARR-HOST-2-IP-ADDRESS 200 0 0 218 Does anyone know what might cause this problem and how I can resolve it?

Read the article
Firebox 1250e Core Failing?

- by Noah

We have 2 Firebox 1250e Core firewall boxes in our production environment, serving as an active and passive mode. A few months back, the active box was flashing a warning light, so our consultant removed it, and plugged it in to a test network. Everything appeared to be working fine, so he reloaded it into the production environment, and we didn't see any other issues. Fast forward to last week, and out network was constantly dropping connections over RDC, timing out, and performing as if there was a traffic issue. I turned off the production box and everything began to work fine immediately. At this point though, I'm not sure how to proceed. Should the box be completely replaced? Is there any recommended testing we could do to determine if there is a failure of some type with this device? Should we try upgrading the software on it? I know the environment isn't the issue, since the passive box (which is now the active one) is working fine. We'd like to have 2 in production though for safety failover purposes. I am not a network admin, but am hoping someone here might be able to provide some guidance.

Read the article
Windows 7 XP Mode-Program not ending properly

- by iceman33

We currently have recently have implemented a few new machines to our network with Windows 7 Enterprise 64-bit installed on them. We have a program that is incompatible with Windows 7 right now and we have it installed on the Windows XP Mode that we have setup on there. There is a shortcut that is on the desktop to have it work with integration services and that part is working successfully. Occasionally, this program will stop working over the server on which it connects to has to get rebooted and the program has to get closed out. However, that process that is in the task manager doesn't seem to close out properly. So in order to correctly get the program shut down, we have to make the users log back into xp mode and do a Ctrl+Alt+Delete to kill the process or have to go back into the machine to perform a restart. I was wondering if anyone has come across a way within XP Mode yet that when the virtual machine goes into hibernation mode that it would shut down all processes or if when restarting the virtual machine your normal machine that it would shut everything down in the virtual XP mode as well and not just keep that program running? Any help would be greatly appreciated.

Read the article
Apache-style multiviews with Nginx

- by Kenn

I'm interested in switching from Apache/mod_php to Nginx for some non-CMS sites I'm running. The sites in question are either completely static HTML files or simple PHP, but the one thing they have in common is that I'm currently using Apache's mod_negotiation to serve them up without file extensions. I'm not concerned with actual content negotiation; I'm using this just so I don't have to use file extensions in my URLs. For example, the file at /info/contact.php is accessed via a URL of just /info/contact The actual file is a .php file in that location, but I don't use the extension in the URLs. This gives me slightly shorter, cleaner URLs and also doesn't expose what's essentially a meaningless implementation detail to the user. In Apache, all this takes is enabling mod_negotiation and adding +MultiViews to the Options for the site. In Nginx I gather I'll be rewriting somehow but being new to Nginx, I'm not exactly sure how to do it. These sites are currently working fine proxied from Nginx to Apache, but I'd like to try running them solely with Nginx/fastcgi. They work fine this way as long as I'm using the extensions, so the fastcgi aspect is working great. My concern now is just with removing those extensions. It's important to keep in mind that the filename is not always in the URL, in the case of subdirectories. That is, /foo/bar should look for /foo/bar.php or /foo/bar/index.php /foo/ should look for /foo/index.php Is there a simple way to achieve this with Nginx or should I stick with proxying to Apache?

Read the article
JBossMQ - Clustered Queues/NameNotFoundException: QueueConnectionFactory error

- by mfarver

I am trying to get an application working on a JBoss Cluster. It uses Queues internally, and the developer claims that it should work correctly in a clustered environment. I have jbossmq setup as a ha-singleton on the cluster. The application works correctly on whichever node currently is running the queue, but fails on the other nodes with a: "javax.naming.NameNotFoundException: QueueConnectionFactory not bound" error. I can look at JNDIview from the jmx-console and see that indeed the QueueConnectionFactory class only appears on the primary node in the Global context. Is there a way to see the Cluster's JNDI listing instead of each server? The steps I took from a default Jboss 4.2.3.GA installation were to use the "all" configuration. Then removed /server/all/deploy/hsqldb-ds.xml and /deploy-hasingleton/jms/hsqldb-jdbc2-service.xml, copying the example/jms/mysq-jdbc2-service.xml file into its place (editing that file to use DefaultDS instead of MySqlDS). Finally I created a mysql-ds.xml file in the deploy directory pointing "DefaultDS" at an empty database. I created a -services.xml file in the deploy directory with the queue definition. like the one below: <server> <mbean code="org.jboss.mq.server.jmx.Queue" name="jboss.mq.destination:service=Queue,name=myfirstqueue"> <depends optional-attribute-name="DestinationManager"> jboss.mq:service=DestinationManager </depends> </mbean> </server> All of the other cluster features of working, the servers list each other in the view, and sessions are replicating back and forth. The JBoss documentation is somewhat light in this area, is there another setting I might have missed? Or is this likely to be a code issue (is there different code to do a JNDI lookup in a clusted environment?) Thanks

Read the article
Laptop shuts down randomly without warning

- by Robert P.

My Asus Zenbook UX32V turns off randomly when I'm working on it. This happens both when the computer is recently turned on (5 minutes), and after being on for several days. I'm not running any heavy software The laptop is not heating The fan is not working on the maximum capacity (it's not heating) It happens when the laptop is lying still on the table It is no warning, it simply goes black It happens both when charging and on battery My guess is that it suddenly lose power somehow. What puzzles me is that I can flip the laptop upside down, sideways, shake it, etc. without it shutting off. This makes me think it's not something that's loose causing occasional short-circuits. I realize that the laptop probably doesn't like flipping and shaking, but it was the best way I could troubleshoot. I rarely turn the computer off, only have it in hibernate or sleep mode (most often hibernate). I've never experienced that the laptop is off when I wake it up from sleep mode. I've had the problem for a few months and it happens 2-8 times a week. Specs: Asus Zenbook UX32V Windows 8.1 (it happened in Windows 8.0 too) Intel i5-3317U CPU @ 1.70GHz The laptop is approx 1.5 years, but it has a small dent on one of the sides that probably voids the warranty. The dent has been there since week one and I don't think it's related to the problems I'm having now. Does anyone have a clue what might cause this, and how it might be fixed? I've read all other questions (some of which are listed below) that seem related to my issue, but none report the same behavior as I'm experiencing. Most report heavy games, heating etc. Asus N53J Laptop randomly shuts down Laptop is randomly shutting off Computer shuts down without warning My laptop acer aspire 5720 suddenly turn off randomly Computer randomly shutting down Windows 8.1 randomly shuts self down ASUS K55VM Laptop unexpectedly shuts down

Read the article
Setup 2003 R2 Radius server to work on vista/seven

- by Fox

Hi All, I'm currently trying to configure my 2003 R2 server RADIUS module to enable WIFI client to authenticate throught my Active Directory. The RADIUS server use MS-CHAP V2 as encryption method. I got several Access Point running DD-WRT, configured to use WPA2-Enterprise security that use Radius Server. Everything is setup, and almost working. When I say almost working, I mean, I can login using my AD Credential on my IPod or even on a MacBook running OS X, Windows XP also work with some little tweak in connection properties. The problem is Windows Vista or Windows Seven clients computers that are not inside domain. It doesn't work at all, it doesn't even prompt for user/password/domain. I already install the patch for IAS to make the certsrv compatible with Vista and Seven, but still doesn't work. Anyone ever encounter the same issue I have right now? I'm searching for a solution to this for several already and still not find anything. Looks like many people have the same issue too. Thanks all for you eventual answers.

Read the article
Apache stops responding to http requests -- https continues to work

- by Apropos

Okay. Very strange problem that I'm having here. I just recently updated to Apache 2.4.2 from 2.2.17, mostly to try to get name-based SSL VirtualHosts working (although they should have been working on 2.2.17). Server is Win2008 R2 (so x64 by definition) running with PHP 5.4.3 and MySQL 5.1.40 (outdated, I know). When I launch the server, it initially works fine. Responds to all requests, VirtualHosts all in order. However, after an uncertain amount of time (appears to only take a few minutes for the most part, but sometimes takes hours), it stops responding to regular HTTP requests (on any VirtualHost). HTTPS continues to work. No errors in the log, and nothing in the access logs when I attempt to connect. I'm having a hard time finding the source of this error given its intermittent nature. When removing all SSL-based VirtualHosts, it seemingly increased stability (still responding to HTTP requests twelve hours later). This could be mere coincidence, though. Entirety of SSL VirtualHost is as follows, should there happen to be a problem with it. <VirtualHost *:443> DocumentRoot "C:\Server\www\virtualhosts\mysite.net" ErrorLog logs/ssl.mysite.net-error_log CustomLog logs/ssl.mysite.net-access_log common env=!dontlog SSLEngine on SSLProtocol all -SSLv2 SSLCipherSuite ALL:!ADH:!EXPORT:!SSLv2:RC4+RSA:+HIGH:+MEDIUM SSLCertificateFile C:/Server/bin/apache/apache2.4.2/conf/ssl/server.crt SSLCertificateKeyFile C:/Server/bin/apache/apache2.4.2/conf/ssl/server.key SSLCertificateChainFile C:/Server/bin/apache/Apache2.4.2/conf/ssl/sub.class1.server.ca.pem SSLCACertificateFile C:/Server/bin/apache/Apache2.4.2/conf/ssl/ca.pem </VirtualHost> Any ideas what I'm missing?

Read the article
RTL8192SU + RTL8191E Linux Issue Installing Driver

- by s32ialx

OK I've read tons of fourms of people getting the onboard RTL8191E working and the RTL8192SU working dif is U = USB they are both N and i have both Toshiba L500D-00T pre-installed Win Vistax64-HP and i have obtained the free Win7x64-HP upgrade the onboard wificard sucks and can't hold a stable connection for more then 20minutes in windows but the usb is amazing. Now problem is i tried both Ubuntu and Mandriva with no resolve the issue is the onboard drive detects and actually SHOWS that it's there but no wireless networks detect so it's saying no SSID's are broadcasting which i know is a lie since I'm running a 2wire bell dsl modem with built in wifi and a Linksys wrt54g w/ DD-WRT firmware and both are broadcasting fine. Why don't i use the USB? new in Mandriva Linux Control Center 2010.0 it shows up in Other/Unknown as RTL8191S WLAN Adapter and on the right pane this shows up Identification Vendor: ?Manufacturer Realtek Description: ?RTL8191S WLAN Adapter Media class: ? Connection Bus: ?USB Bus PCI #: ?1 PCI device #: ?5 Vendor ID: ?0x0bda Device ID: ?0x8172 Sub vendor ID: ?0x0000 Sub device ID: ?0x0000 Misc Module: ?rtl819xU In the hardware device manager in mandriva it shows up as unknown but shows that it's realtek and that it's a 8192 chipset. but no option to for a driver install and when i do a make in terminal i get this error and no clue what it means [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# make make: *** /lib/modules/2.6.31.12-desktop-3mnb/build: No such file or directory. Stop. make: *** [all] Error 2 [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# any help appreciated. and just encase I'm running currently Mandriva Spring 2010 Free

Read the article
Using a named pipe to simulate a serial port on a VMware virtual machine (linux host and client)

- by Dave M

Trying to write a python program to create a simulated data stream and feed it, through a named pipe, to a VMware virtual machine. The host is running Ubuntu 11.10 and VMware player 5.0.0. The Vm is running Ubuntu netbook 10.04. I am able to get the pipe working on the local machine but I am not able to get the pipe to pass data through the virtual serial port to the programs running on the virtual machine. #!/usr/bin/python import os # # Create a named pipe that will be used as the serial port on a VMware virtual machine SerialPipe = '/tmp/gpsd2NMEA' try: os.unlink(SerialPipe) except: pass os.mkfifo(SerialPipe) # # Open the named pipe NMEApipe = os.open(SerialPipe, os.O_RDWR|os.O_NONBLOCK) # # Write a string to the named pipe NMEAtime = "235959" os.write(NMEApipe, str( '%s\n' % NMEAtime )) Test to see if the python program is working on the host machine (displays 235959 if data is passing through the pipe) $ cat /tmp/gpsd2NMEA 235959 Serial port as defined in the VMware .vmx file: serial0.present = "TRUE" serial0.startConnected = "TRUE" serial0.fileType = "pipe" serial0.fileName = "/tmp/gpsd2NMEA" serial0.pipe.endPoint = "client" serial0.autodetect = "FALSE" serial0.tryNoRxLoss = "TRUE" serial0.yieldOnMsrRead = "TRUE" Test to see if the serial port in the VM is receiving data $ cat /dev/ttyS0 or $ minicom -D /dev/ttyS0 or $ stty -F /dev/ttyS0 cs8 -parenb -cstopb 115200 $ echo < /dev/ttyS0 None of these display any data from the python program.

Read the article
PC can't detect second RAM installed

- by kulwinder

I have PC with 512 MB RAM installed (motherboard manufacture MICRO STAR, chipset P4M800), pc was running very slow so I decided to upgrade the ram. I installed CPU-Z and check the ram installed on the machine, also had a look at the stick installed. 512 MB PC 3200 400 MHz DDR but my mother supports 200 MHz and it was working ok. So I bought 2GB which I checked on manual that it support upto 2 GB Ram. So I installed 2GB PC 3200 400 MHz same as the old one, I plugged in both eventhough motherboard only support upto 2 GB but system spec only shows 512 (deducts 64 MB shared vga memory) I checked on CPU-Z, it detects both, slot 1 512 MB, slot 2 2048 MB, comparing screen for both slots, both the same, volt 2.5, frequency 166 MHz and 200MHz, only difference on those is 2gb ram shows under timings table 133MHz 166 MHz and 200MHz but 512 MB shows only 166MHz and 200MHz. I checked on Google and can't seems to figure out whats wrong with it. If I only plug in 2GB. Pc doesn't boot up like ram not working.With only 512 MB plugged in seems ok. Please help.

Read the article
Debian/Ubuntu - No network connection

- by leviathanus

I have a very weird situation on my Ubuntu 12.04 LTS Server. I can not access (ping) my gateway, although I believe my config is ok - I attach the outputs. Any hints where to look? (I changed the beginning of the IP to something different, just obfuscation) ping 5.9.10.129 PING 5.9.10.129 (5.9.10.129) 56(84) bytes of data. From 5.9.10.129 (5.9.10.129) icmp_seq=2 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=3 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=4 Destination Host Unreachable uname -r 3.2.0-29-generic ifconfig eth0 eth0 Link encap:Ethernet HWaddr 3c:97:0e:0e:54:d7 inet addr:5.9.10.142 Bcast:5.9.10.159 Mask:255.255.255.224 inet6 addr: fe80::8e70:5aff:feda:c4ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1216 errors:0 dropped:0 overruns:0 frame:0 TX packets:490 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107470 (107.4 KB) TX bytes:34344 (34.3 KB) Interrupt:17 Memory:d2500000-d2520000 ip route default via 5.9.10.129 dev eth0 metric 100 5.9.10.128/27 via 5.9.10.129 dev eth0 5.9.10.128/27 dev eth0 proto kernel scope link src 5.9.10.142 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 5.9.10.129 0.0.0.0 UG 1000 0 0 eth0 5.9.10.128 5.9.10.129 255.255.255.224 UG 0 0 0 eth0 5.9.10.128 0.0.0.0 255.255.255.224 U 0 0 0 eth0 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination UPD: Eric, this is how routing information looks on a working server: 0.0.0.0 78.47.198.49 0.0.0.0 UG 100 0 0 eth0 78.47.198.48 78.47.198.49 255.255.255.240 UG 0 0 0 eth0 78.47.198.48 0.0.0.0 255.255.255.240 U 0 0 0 eth0 As I understand it, Hetzner tries to ensure security by this, so I can not take over an IP by changing my MAC. But this is another server, which has another netmask (255.255.255.240) UPD2: BatchyX, on the working server: 78.47.198.49 dev eth0 src 78.47.198.60 cache on the broken: 5.9.10.129 dev eth0 src 5.9.10.142 cache

Read the article
Being a more attractive job candidate - Certs XOR Degree

- by Zephyr Pellerin

I'm currently working in an IT position, where I do helpdesk stuff, and predominantly security related issues/consulting (In the loosest sense of the term) In-House and for Service-Contract clients (as the only/acting CCSP [I guess I should say only person with Cisco experience] in my organization). I've professionally written Kernel Mode drivers for a gaming company. Among other things that I'm proud to put on a resume. I think of myself as very reasonably qualified as a System Administrator, With excellent Cisco experience, among other things I think would make a good addition to almost any IT staff in need of a new employee. However, Something has always tripped me up - Human Resources. Let me explain, I decided to skip the university route - I'm immensely glad that I did, The computer science graduates that I've met and work with rarely know much of anything about Computers (Until they gain some 'real' experience), Even when asked about Theoretical Computing fundamentals they can rattle something off about Turing Completeness but rarely do they understand the mathematical underpinnings. In short, I think instead of going to college, I'd rather pick up some real world experience. However, Apparently, Employers rarely think the same way. A quick perusal of jobs through the standard job search engine yields nothing short of a conspiracy to exclude anyone without 'A Bachelors Degree in Computer Science or Equivalent'. Interviews I've had in the past have almost always been entangled with - 1. My Age (Which I can't really change) and 2. Lack of Degree. Employers frequently disregard the CCNA/CCSP, The experience I've gained through internships, My extensive experience in x86 assembly and C, among so many other things I like to think are valuable to employers - In lieu of the fact that I don't have a piece of paper. So, AS AN EMPLOYER - Is it even worth working on my CCIE? Or should I pad my resume with certifications that are easier to acquire (Like CISSP, MSCE, Network+, etc.). Or should I ditch the whole idea and head back to get a Mathematics or CS degree?

Read the article
I think installing PostFix solved my problem, but it seemed *too* easy

- by Joel Marcey

Hi, This is a followup to a serverfault post I made a while ago: http://serverfault.com/questions/21633/how-do-i-target-a-different-mail-server-depending-on-domain-with-exim (More context here too: http://forum.slicehost.com/comments.php?DiscussionID=3806 ) I have a slice/VPS at Slicehost. I basically decided to scrap exim (i.e., purge it), and start anew with my email infrastructure. In case you didn't read any of the above threads, basically my goal was to have a send only mail infrastructure that relays all outgoing email to Google Apps. I also wanted to where email from domain1 (a Wordpress installation) would show it coming from domain1.com and email from domain2 (a normal website) would show it coming from domain2.com. So I decided to give PostFix a try. I literally followed the surprisingly simple instructions here: http://sudhanshuraheja.com/2009/02/slicehost-setup-outgoing-mail-google-apps-postfix/ And voila, all seems to be working as I expected. My email tests show email coming from the proper locations (either domain1 or domain2 depending on where the emails were sent from). But this all seemed too simple to me. So simple, in fact, that I feel that something is amiss. When I installed PostFix according to the instructions in the post above and it worked, I was surprised that I didn't have to specify an SMTP server, a port number, any authentication credentials, etc. My slice is set up such that I have MX records for Google Apps (e.g., ASPMX.L.GOOGLE.COM.) in my DNS settings, but I am not sure if that is why it is working. My email infrastructure knowledge is admittedly limited, but with this am I suspect to: Spammers using my email infrastructure? My emails going to people as spam? Something else sinister? I have actually stopped running PostFix until I understand this better. Thanks!

Read the article
Disk Partitioning problem with fdisk.

- by MA1

Currently i am using fdisk to create/resize windows partitions. Following is a sample input script to fdisk to create/resize windows partitions: fdisk /dev/sda < partInput the contents of partInput are as follows: d #delete the partition 3 #partition number to be deleted n #add a new partition p #primary: type of new partition 3 #new partition number 18804 #start cylinder of new partition 77433 #end cylinder of new partition t #change the type of partition 3 #partition number whose type(filesystem) is to be changed 7 #HPFS/NTFS: partition type(filesystem) n #add a new partition p #primary: type of partition 77434 #first cylinder of new partition 77825 #end cylinder new partition w #write all the above changes As you see in the above input we are using cylinders for start and end. Earlier i am using sectors as unit and everything is working fine but getting problems when partitioning a 1.5TB hard drive. Then i changed the unit to cylinders but it is working on some machines not all. On some machines fdisk failed to create the partition table correctly. So, i am thinking to move to parted if there is no way to do the above using fdisk. Please also tell me how to correctly convert sectors to cylinders? How to perform all the above steps using parted without losing the data OR how to use fdisk correctly?

Read the article
Apache error "child pid XXXX exit signal exceeded file size limit (25)"

- by Stephen Melrose

Morning all, Apache on our internal development server stopped working last night. It's running, but all we get is a blank screen, no server errors. Examing the error log shows the following, [Fri Apr 23 09:13:57 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:03 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:03 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:06 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) After some Googling, we found that this is due to Apache trying to handle a file greater than it's maximum allowed limit, which by default is 2GB and is usually an error log. I did a search using find . -size +1000000k -ls (find all files greater than 1GB) in our log and web folders, but nothing showed up. I've also restarted Apache and rebooted the server itself serveral times. I've completely wiped the log folder and started a fresh. Nothing is working. Any ideas as to what else might be causing this? Thank you

Read the article
How to set up port forwarding on a dedicated server running CentOS 5.4 to use Ubuntu 9.0.4

- by mairtinh

The basic situation that I have is a dedicated server running CentOS 5.4 At the moment I have one VM running Ubuntu 9.0.4. Later on, I will want to add another VM running Windows Server 2003 but at the moment I am focusing on getting Ubuntu up and running. The Ubuntu installation is working fine but I'm seriously struggling to get port forwarding working so that I can access websites to be hosted on the Ubuntu VM. As a newbie to Linux, I am confused about the relationship between IPTables and VMWare's own port forwarding. Here's what I've tried so far. The IP of my server is xxx.xxx.xxx.xxx and the provider support have told me that the subnet mask is 255.255.255.0, the gateway address is xxx.xxx.xxx.1 and the network address is xxx.xxx.xxx.0. (Those latter two surprise me a bit, I expected private gateway/network address rather than public ones.) First of all I tried Bridged Networking but had no success at all in communicating with the machine other than through the VMware console. I tried pinging it from the host (using ssh into the host) but no joy; also no Inernet access from the VM. I changed the interfaces configuration from DHCP to Static, using a static address of 192.168.1.100 and setting the gateway to xxx.xxx.xxx.1 as advised by the provider. No real difference, still cannot ping the guest from the host or vice versa and no Internet access from the guest. Then I tried NAT. The host automatically set the IP address to 192.168.132.128 with a gateway of 192.168.132.2 Now the guest has Internet access out and when I do a VNC to the host and open Firefox with 192.168.132.128 I can see the hosted website okay but I still cannot get into it from outside. I mentioned that I'm a bit confused about IPtables and VMware port forwarding, what I meant is that I'm not sure whether IPtable forwarding should be set to the IP address of the guest interface (192.168.132.128 in this case) or the gateway address 192.168.132.2 . I have a feeling that I'm missing something very simple here, can anybody tell me what it is?

Read the article
IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing issue

- by Ernest Mueller

I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

Read the article
Webapp in Jetty can't find properties file after running a couple days

- by Cuga

I have a webapp running in Jetty on Mac OS 10.6. After a few days of it running and without the server losing power or rebooting, it seems to stop working saying it can't find a properties file. This properties file is included inside the .war file deployed to the /webapps directory. If I restart Jetty as the superuser the web service works again just fine. Can anyone lend any advice to what's going on and how I can fix it? The error being shown when it isn't working is: Problem accessing /my-web-service. Reason: INTERNAL_SERVER_ERROR Caused by: java.lang.NullPointerException at com.company.service.Dao.readFromPropertiesFile(BwDao.java:35) at com.company.service.ServletHandler.doGet(ProxyClass.java:66) ... at org.mortbay.jetty.HttpConnection.handle(HttpConnection.java:404) at org.mortbay.io.nio.SelectChannelEndPoint.run(SelectChannelEndPoint.java:410) at org.mortbay.thread.QueuedThreadPool$PoolThread.run(QueuedThreadPool.java:582) Here's where the properties files exist that it's trying to read from the .war file: And this is how the properties are being read from the classpath: Properties properties = new Properties(); properties.load(Thread.currentThread().getContextClassLoader().getResourceAsStream( "app.properties")); Again, this does work just fine if I have just restarted the server, but it seems to fail after running a few days.

Read the article
Windows Firewall Software to Filter Transit Traffic

- by soonts

I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

Read the article
Add files/folders/Apps to a new User Account

- by odeho19

I have created a new user acct. for my roommate. I/we don't really care much for IE, and I'd like to add Google Chrome, and FF for her, to let her choose her own browser. Plus I'd like to add some other apps for her, and transfer some of her personal info that she's been storing on my administrative acct. (i.e. personal photos and such). So, like I said the account is set up. But when I go to use Chrome, it won't open. It, along with other apps are listed in the list of "approved" applications under the parental control list. (Application Restrictions List) But they either don't show up when searched for,( in her acct.) or won't open and operate. One other example is Faststone Capture. And then, I've got one application, Yahoo, "Unchecked", and yet there it is in her account, AND IT WORKS! I do not get it. The purpose to setting up an account for her was to only restrict that she couldn't delete, or uninstall anything on the computer. I don't care, (obviously within reason) what she installs, but NO TAKING AWAY! lol Here is a screen shot of the restrictions list: So, here I sit, wondering what I did wrong, or forgot to do in order for these to work. I don't care if Yahoo works or not. But her photos being transferred, Chrome/FF working, and Faststone Capture working, are a priority for me. If anyone has any ideas, I would appreciate any advice. Thanks! OH Edit: Also, my account is an Administrative one. The account I am creating for her is just a Standard User Acct.

Read the article
apache using mod_auth_kerb always asks for the password twice

- by DrStalker

(Debian Squeeze) I'm trying to set apache up to use Kerberos authentication to allow AD users to log in. It is working, but prompts the user twice for a username and password, with the first time being ignored (no matter what is put it in.) Only the second prompt includes the AuthName string from the config (i.e.: the first windows is a generic username/password one, the second includes the title "Kerberos Login") I'm not worried about integrated windows authentication working at this stage, I just want users to be able to login with their AD account so we don't need to set up a second repository of user accounts. How do I fix this to eliminate that first useless prompt? The directives in the apache2.conf file: <Directory /var/www/kerberos> AuthType Kerberos AuthName "Kerberos Login" KrbMethodNegotiate On KrbMethodK5Passwd On KrbAuthRealms ONEVUE.COM.AU.LOCAL Krb5KeyTab /etc/krb5.keytab KrbServiceName HTTP/[email protected] require valid-user </Directory> krb5.conf: [libdefaults] default_realm = ONEVUE.COM.AU.LOCAL [realms] ONEVUE.COM.AU.LOCAL = { kdc = SYD01PWDC01.ONEVUE.COM.AU.LOCAL master_kdc = SYD01PWDC01.ONEVUE.COM.AU.LOCAL admin_server = SYD01PWDC01.ONEVUE.COM.AU.LOCAL default_domain = ONEVUE.COM.AU.LOCAL } [login] krb4_convert = true krb4_get_tickets = false The access log when accessing the secured directory (note the two seperate 401's) 192.168.10.115 - - [24/Aug/2012:15:52:01 +1000] "GET /kerberos/ HTTP/1.1" 401 710 "-" "Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.1 (KHTML, like Gecko) Chrome/21.0.1180.83 Safari/537.1" 192.168.10.115 - - [24/Aug/2012:15:52:06 +1000] "GET /kerberos/ HTTP/1.1" 401 680 "-" "Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.1 (KHTML, like Gecko) Chrome/21.0.1180.83 Safari/537.1" 192.168.10.115 - [email protected] [24/Aug/2012:15:52:10 +1000] "GET /kerberos/ HTTP/1.1" 200 375 "-" "Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.1 (KHTML, like Gecko) Chrome/21.0.1180.83 Safari/537.1" And one line in error.log [Fri Aug 24 15:52:06 2012] [error] [client 192.168.0.115] gss_accept_sec_context(2) failed: An unsupported mechanism was requested (, Unknown error)

Read the article
TFTP Timing Out on Ubuntu VM

- by valsidalv

I'm running a Windows 7 PC with VMware installed which has my Ubuntu (10.04 Lucid Lynx). I recently installed a DHCP server and TFTP (Xinet tftpd) using these instructions. I've mapped a network drive so that my Windows has access to all the files in my VM through a 192.x.x.x IP address. I'm trying to throw some custom firmware onto a router. The router has its own built-in TFTP utility that will download the image. It successfully manages to do everything but it is slow because it writes it to flash memory. There is another method that is much quicker because it writes to RAM directly but it must use the TFTP server in Ubuntu. The issue I'm facing is that the Ubuntu TFTP transfer seems to be timing out. The transfer starts but never goes past ~60%. Here's my /etc/xinetd.d/tftp file (similar to a known working config): service tftp { protocol = udp port = 69 socket_type = dgram wait = yes user = nobody server = /usr/sbin/in.tftpd server_args = -s /home/user/tftp/ disable = no cps = 300 2 per_source = 60 } I've done some searching but can't find any parameters for this file to control timeout time or number of retries. The last two arguments (cps, per_source) and completely alien to me (can anyone explain). I have a few possible solutions but the easiest would be to get this TFTP server working. Can anyone help? Either with a timeout configuration or maybe even recommend a different TFTP server? Thanks!

Read the article

< Previous Page | 446 447 448 449 450 451 452 453 454 455 456 457 | Next Page >