Search Results

Search found 12754 results on 511 pages for 'cached mode'.

Page 455/511 | < Previous Page | 451 452 453 454 455 456 457 458 459 460 461 462  | Next Page >

• HAproxy roundrobin balancing does not appear to be distributing evently

  - by andrew

  Hello, I know that with loaded servers, roundrobin in HAproxy (1.4.4) does not evenly distribute, but my servers are currently getting NO traffic (test setup), and roundrobin balancing does www1,www1,www1,www1,www1,...www2,www2,www2,...,www1... I'm verifying this by having the script being run on each server cat /etc/HOSTNAME (slackware). I need to have it switch back and forth each time to test some session stuff (stored in shared memcached) but am having trouble getting it to switch between my two web servers on each request. global log 127.0.0.1 local0 warning maxconn 4096 chroot /usr/share/haproxy pidfile /var/run/haproxy.pid uid 99 gid 99 daemon defaults balance roundrobin fullconn 100 maxconn 4096 mode http option dontlognull option http-server-close option forwardfor option redispatch retries 3 timeout connect 5000 timeout client 20000 timeout server 60000 timeout queue 60000 stats enable stats uri /haproxy stats auth ***:*** frontend www *:80 log global acl is_upload hdr_dom(host) -i uploads.site.com acl is_api hdr_dom(host) -i api.site.com acl is_dev hdr_dom(host) -i dev.site.com acl is_apidev hdr_dom(host) -i apidev.site.com use_backend uploads.site.com if is_upload use_backend api.site.com if is_api use_backend dev.site.com if is_dev !is_apidev default_backend site.com backend site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend api.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:api.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend dev.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:dev.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend uploads.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:uploads.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 backup weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 So basically, I have some different back-ends (I've verified the ACLs are working), with the default option "roundrobin" selected. I've tried removing weights, removing the minconn/maxconn/fullconn attributes for all servers (not just the backend I'm testing), tried removing the ACLs, etc. I've been testing on dev.site.com BTW. Anyone see a reason why I can't get something like www1,www2,www1,www2,...? Also, this is one of my first questions on here, so please let me know if I left anything needed out of my post. Thanks!

  Read the article

• Why do my Application Compatibility Toolkit Data Collectors fail to write to my ACT Log Share?

  - by Jay Michaud

  I am trying to get the Microsoft Application Compatibility Toolkit 5.6 (version 5.6.7320.0) to work, but I cannot get the Data Collectors to write to the ACT Log Share. The configuration is as follows. Machine: ACT-Server Domain: mydomain.example.com OS: Windows 7 Enterprise 64-bit Edition Windows Firewall configuration: File and Printer Sharing (SMB-In) is enabled for Public, Domain, and Private networks ACT Log Share: ACT Share permissions*: Group/user names Allow permissions --------------------------------------- Everyone Full Control Administrator Full Control Domain Admins Full Control Administrators Full Control ANONYMOUS LOGON Full Control Folder permissions*: Group/user name Allow permissions Apply to ------------------------------------------------- ANONYMOUS LOGON Read, write & execute This folder, subfolders, and files Domain Admins Full control This folder, subfolders, and files Everyone Read, write & execute This folder, subfolders, and files Administrators Full control This folder, subfolders, and files CREATOR OWNER Full control Subfolders and files SYSTEM Full control This folder, subfolders, and files INTERACTIVE Traverse folder / This folder, subfolders, and files execute file, List folder / read data, Read attributes, Read extended attributes, Create files / write data, Create folders / append data, Write attributes, Write extended attributes, Delete subfolders and files, Delete, Read permissions SERVICE (same as INTERACTIVE) BATCH (same as INTERACTIVE) *I am fully aware that these permissions are excessive, but that is beside the point of this question. Some of the clients running the Data Collector are domain members, but some are not. I am working under the assumption that this is a Windows file sharing permission issue or a network access policy issue, but of course, I could be wrong. It is my understanding that the Data Collector runs in the security context of the SYSTEM account, which for domain members appears on the network as MYDOMAIN\machineaccount. It is also my understanding from reading numerous pieces of documentation that setting the ANONYMOUS LOGON permissions as I have above should allow these computer accounts and non-domain-joined computers to access the share. To test connectivity, I set up the Windows XP Mode virtual machine (VM) on ACT-Server. In the VM, I opened a command prompt running as SYSTEM (using the old "at" command trick). I used this command prompt to run explorer.exe. In this Windows Explorer instance, I typed \ACT-Server\ACT into the address bar, and then I was prompted for logon credentials. The goal, though, was not to be prompted. I also used the "net use /delete" command in the command prompt window to delete connections to the ACT-Server\IPC$ share each time my connection attempt failed. I have made sure that the appropriate exceptions are Since ACT-Server is a domain member, the "Network access: Sharing and security model for local accounts" security policy is set to "Classic - local users authenticate as themselves". In spite of this, I still tried enabling the Guest account and adding permissions for it on the share to no effect. What am I missing here? How do I allow anonymous logons to a shared folder as a step toward getting my ACT Data Collectors to deposit their data correctly? Am I even on the right track, or is the issue elsewhere?

  Read the article

• How to change key mappings in Cygwin's Vim

  - by Boldewyn

  I'm using Vim under Debian, Win Vista and WinXP (the latter two with Cygwin). To handle tabs more easily, I mapped <C-Left> and <C-Right> to :tab(prev|next). This mapping works like a charm on the Debian machine. On the Windows machines, however, pressing <C-Left> deletes 5 lines, as far as I can tell, and meddles with cursor position, while <C-Right> does this, too, and additionally enters Insert mode. Question: To put it in a nutshell, how can I find out, why Vim behaves as it does? Is there a way to backtrace the active commands and keystrokes? Could there be a plugin the culprit? (I didn't install one, perhaps a default include by the Cygwin distro...) If so, how can I find it? Edit 1: OK, it seems, that I got a first trace: The terminal sends for <C-Left> '^[[1;5D', and for right '^[[1;5C' (evaluated with the <C-V><C-Left> trick). If vim interprets this literally and discards the first characters, it explains the strange behaviour. Any ideas, how I could change this key mapping? Additional Diagnosis: This behaviour occurs regardless of any existing ~/.vimrc file (is therefore not related to my above mentioned mapings) and is not inherited of some /etc/vim/vimrc, since this doesn't exist in the default Cygwin installation. :verbose map doesn't yield any new insights. Either nothing or my mentioned mappings appear, based on the existence of the .vimrc file :help <C-Left> suggests, that the default would be a simple cursor movement, which is apparently not the case. Vim's version under Cygwin: VIM - Vi IMproved 7.2 (2008 Aug 9, compiled Feb 11 2010 17:36:58) Included patches: 1-264 Compiled by http://cygwin.com/ Huge version without GUI. Features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent -clientserver -clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +cryptv +cscope +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +fork() -gettext -hangul_input +iconv +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap +menu +mksession +modify_fname +mouse -mouseshape +mouse_dec -mouse_gpm -mouse_jsbterm +mouse_netterm -mouse_sysmouse +mouse_xterm +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +postscript +printer +profile -python +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl +terminfo +termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -X11 -xfontset -xim -xsmp -xterm_clipboard -xterm_save system vimrc file: "$VIM/vimrc" user vimrc file: "$HOME/.vimrc" user exrc file: "$HOME/.exrc" fall-back for $VIM: "/usr/share/vim" Compilation: gcc -c -I. -Iproto -DHAVE_CONFIG_H -g -O2 -D_FORTIFY_SOURCE=1 Linking: gcc -L/usr/local/lib -o vim.exe -lm -lncurses -liconv

  Read the article

• How to find out Vim's currently mapped commandos

  - by Boldewyn

  I'm using Vim under Debian, Win Vista and WinXP (the latter two with Cygwin). To handle tabs more easily, I mapped <C-Left> and <C-Right> to :tab(prev|next). This mapping works like a charm on the Debian machine. On the Windows machines, however, pressing <C-Left> deletes 5 lines, as far as I can tell, and meddles with cursor position, while <C-Right> does this, too, and additionally enters Insert mode. Question: To put it in a nutshell, how can I find out, why Vim behaves as it does? Is there a way to backtrace the active commands and keystrokes? Could there be a plugin the culprit? (I didn't install one, perhaps a default include by the Cygwin distro...) If so, how can I find it? Additional Diagnosis: This behaviour occurs regardless of any existing ~/.vimrc file (is therefore not related to my above mentioned mapings) and is not inherited of some /etc/vim/vimrc, since this doesn't exist in the default Cygwin installation. :verbose map doesn't yield any new insights. Either nothing or my mentioned mappings appear, based on the existence of the .vimrc file :help <C-Left> suggests, that the default would be a simple cursor movement, which is apparently not the case. Vim's version under Cygwin: VIM - Vi IMproved 7.2 (2008 Aug 9, compiled Feb 11 2010 17:36:58) Included patches: 1-264 Compiled by http://cygwin.com/ Huge version without GUI. Features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent -clientserver -clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +cryptv +cscope +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +fork() -gettext -hangul_input +iconv +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap +menu +mksession +modify_fname +mouse -mouseshape +mouse_dec -mouse_gpm -mouse_jsbterm +mouse_netterm -mouse_sysmouse +mouse_xterm +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +postscript +printer +profile -python +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl +terminfo +termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -X11 -xfontset -xim -xsmp -xterm_clipboard -xterm_save system vimrc file: "$VIM/vimrc" user vimrc file: "$HOME/.vimrc" user exrc file: "$HOME/.exrc" fall-back for $VIM: "/usr/share/vim" Compilation: gcc -c -I. -Iproto -DHAVE_CONFIG_H -g -O2 -D_FORTIFY_SOURCE=1 Linking: gcc -L/usr/local/lib -o vim.exe -lm -lncurses -liconv

  Read the article

• Why is mount -a not mounting fuse drive properly when executed remotely (via Fabric)?

  - by Jim D

  This is a weird bug and I'm not sure where it's coming from. Here's a quick run down of what I'm doing. I'm trying to mount a FUSE drive to an Amazon EC2 instance running Ubuntu 10.10 using s3fs (FUSE over Amazon). s3fs is compiled from source according to the instructions etc. I've also added an entry to /etc/fstab so that the drive mounts on boot. Here's what /etc/fstab looks like: # /etc/fstab: static file system information. # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 LABEL=uec-rootfs / ext4 defaults 0 0 /dev/sda2 /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 /dev/sda3 none swap sw,comment=cloudconfig 0 0 s3fs#mybucket /mnt/s3/mybucket fuse default_acl=public-read,use_cache=/tmp,allow_other 0 0 So the good news is that this works fine. On reboot the connection mounts correctly. I can also do: $ sudo umount /mnt/s3/mybucket $ sudo mount -a $ mountpoint /mnt/s3/mybucket /mnt/s3/mybucket is a mountpoint Great, right? Well here's the problem. I'm using Fabric to automate the process of building and managing this instance. I noticed I was getting this error message when using Fabric to build s3fs and set up the mount process: mountpoint: /mnt/s3/mybucket: Transport endpoint is not connected I isolated it down the the problem and built a fabric task that reproduces the problem: def remount_s3fs(): sudo("mount -a") Which does: [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] Executing task 'remount_s3fs' [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] sudo: mount -a [And yes, I was sure to unmount it before running this task.] When I check the mount using mountpoint I get: $ mountpoint /mnt/s3/mybucket mountpoint: /mnt/s3/mybucket: Transport endpoint is not connected Done. But if I run sudo mount -a at the command line, it works. Hrm. Here is that fab task output again, this time in full debug mode: [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] Executing task 'remount_s3fs' [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] sudo: sudo -S -p 'sudo password:' /bin/bash -l -c "mount -a" Again, I get that transport endpoint not connected error. I've also tried copying and pasting the exact command run into my ssh session (i.e. sudo -S -p 'sudo password:' /bin/bash -l -c "mount -a") and it works fine. So...that's my problem. Any ideas?

  Read the article

• Can Vagrant point to a directory of Puppet manifests for execution?

  - by SeligkeitIstInGott

  I am using Vagrant to jump start some initial Puppet config and am confused on how to include/run multiple manifests (other than just site.pp) in the puppet execution workflow without making the extra manifests into modules and including them that way. In the puppet manifests directory that I point Vagrant to (see below) I have two manifests that I want executed: site.pp and hierasetup.pp. config.vm.provision "puppet" do |puppet| puppet.manifests_path = "puppet_files/manifests" puppet.module_path = "puppet_files/modules" puppet.manifest_file = "site.pp" puppet.options = "--verbose --debug" end Currently I am having site.pp be the manifest that calls hierasetup.pp. My site.pp looks like this: File { owner => 'root', group => 'root', mode => '0644', } import "hierasetup.pp" include jboss But I get this error about the deprecation of "import": Warning: The use of 'import' is deprecated at /tmp/vagrant-puppet-1/manifests/site.pp:33. See http://links.puppetlabs.com/puppet-import-deprecation (at grammar.ra:610:in `_reduce_190') According to the referenced URL under "Things to try instead" it says "To keep your node definitions in separate files, specify a directory as your main manifest". Further this puppet doc on main manifests says: "Recommended: If you’re using the main manifest heavily instead of relying on an ENC, consider changing the manifest setting to $confdir/manifests. This lets you split up your top-level code into multiple files while avoiding the import keyword. It will also match the behavior of simple environments." It appears that Puppet can reference an entire directory instead of just a specific manifest file, such that I would expect that Vagrant would make a provision for this and allow me to drop the "puppet.manifest_file = "site.pp" line and point to the parent directory instead in which all the *.pp files there will be executed. However removing that line in Vagrant merely generates a complaint about an expected "default.pp" in its stead: puppet provisioner: * The configured Puppet manifest is missing. Please specify a path to an existing manifest: /some/path/puppet_files/manifests/default.pp So: Firstly, do I understand the "new" (non-import) way of calling multiple manifests correctly, in that a directory is to be pointed to in which all the *.pp files inside it will be executed? And secondly, has Vagrant "caught up" with this new change to accommodate the referencing of directories in conjunction with Puppet's deprecation of "import"? Update: Thanks to Shane the issue with #2 (Vagrant's code not being caught up to allow pointing to puppet manifest directories) was reported on Vagrant's GitHub issue tracker site and has since been patched: https://github.com/mitchellh/vagrant/issues/4169

  Read the article

• "Error 1067: The process terminated unexpectedly" when trying to install MySQL on Win7 x64.

  - by Gravitas

  Hi, I've run into a brick wall trying to install MySQL v5.5 on my machine. My PC is Windows 7 x64, Enterprise edition. MySQL installs fine, but when I run the "MySQL Instance Configuration Wizard", it pauses forever on the step "Start Service" (I can let it run for 30 minutes with no response). If I go into services, I see that the "MySQL" service hasn't started, and if I try to start it, it says "Windows could not start MySQL Service on Local Computer. Error 1067: The process terminated unexpectedly." I've tried the following: Turning off firewall. Uninstalling all antivirus software. Installing / reinstalling 32-bit version of MySQL. Installing / reinstalling 64-bit version of MySQL. Uninstalling, deleting the contents of "C:\program files\MySQL" and "C:\program files (x86)\MySQL", reinstalling. Checking to see that there is no rogue services named MySQL???? (from a previous install). Checking that port 3306 is not used by an alternate program. Changing the default port that MySQL uses. Checking for "my.ini" and "my.ini.cnf" in "C:\windows" (nothing there but that can cause a problem). Running both MySQL installer, and configuration wizard, in "Adminstrator mode". Turning off UAC. Installing with defaults, not changing anything. Rebooting my machine (about 6 reboots so far). Opening up port 3306 in the firewall (both TCP and UDP, inbound and outbound). Swearing at the klutz of a programmer who designed MySQL so you can't even install it (as if that would help!) My machine is working 100% in every other way. InfiniDB (a MySQL compatible database) installs 100%, as does Visual Studio 2010, Microsoft SQL Server, etc, etc. Your advice on how to work around this? p.s. Here is the screen it got stuck on for 15 minutes until I killed the process: Update 2010-12-20 Tried MySQL v5.1, it didn't work either. Its amazing - if you type "mysqld /?", or "mysqld -help", it doesn't give you any help. And, if you try to restart the service manually, it doesn't display any error messages. Could it be any more unhelpful? Update 2010-12-21 Installed MySQL 6.0 alpha, and it worked. However, I'd rather not use an alpha release, given that the "stable" release is anything but :( Update 2010-12-21 Found http://dev.mysql.com/doc/refman/5.1/en/windows-troubleshooting.html, dealing with troubleshooting under Windows. Discovered that you can generate an error log if the service doesn't start - see here: http://dev.mysql.com/doc/refman/5.1/en/error-log.html

  Read the article

• amd gpu but display on intel integrated graphics

  - by pitseeker

  On my Ubuntu 12.04 I connected my monitor to the onboard intel graphics. I'd like to use my ati radeon 6770 for opencl tasks (e.g. bitcoin mining). So far I couldn't figure out how to get the ati driver working. When calling "aticonfig --initial -f" it always writes a new xorg.conf that ignores the intel graphics. At boot time it works only when I attached the monitor to the ati card. So I manually tampered with the xorg.conf and got this: Section "ServerLayout" Identifier "Default Monitor" Screen 0 "myscreen" 0 0 Screen 1 "deadscreen" RightOf "myscreen" EndSection Section "Module" EndSection Section "Monitor" Identifier "Default Monitor" Option "VendorName" "Monitor Vendor" Option "ModelName" "Monitor Name" Option "DPMS" "true" EndSection Section "Monitor" Identifier "null Monitor" Option "Enable" "false" EndSection Section "Device" Identifier "Intel Integrated Graphics" Driver "intel" BusID "PCI:0:2:0" Screen 0 EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" Screen 1 EndSection Section "Screen" Identifier "myscreen" Device "Intel Integrated Graphics" Monitor "Default Monitor" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "deadscreen" Device "aticonfig-Device[0]-0" Monitor "null Monitor" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection I think this might be the right way since I see that X tries to start both drivers in /var/log/Xorg.0.log. However the fglrx driver seems crash (end of xorg.0.log): Backtrace: [ 6.625] 0: /usr/bin/X (xorg_backtrace+0x26) [0x7fb5cd41b846] [ 6.625] 1: /usr/bin/X (0x7fb5cd293000+0x18c6ea) [0x7fb5cd41f6ea] [ 6.625] 2: /lib/x86_64-linux-gnu/libpthread.so.0 (0x7fb5cc5b9000+0xfcb0) [0x7fb5cc5c8cb0] [ 6.625] 3: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/drivers/fglrx_drv.so (xdl_xs111_atiddxGetGPUMapInfo+0x1b1) [0x7fb5c88e16b1] [ 6.625] 4: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/drivers/fglrx_drv.so (atiddxGetGPUMapInfo+0xd) [0x7fb5c87bcc0d] [ 6.625] 5: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1ab29) [0x7fb5ca147b29] [ 6.625] 6: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1cf8c) [0x7fb5ca149f8c] [ 6.625] 7: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1ee55) [0x7fb5ca14be55] [ 6.626] 8: /usr/bin/X (InitExtensions+0x99) [0x7fb5cd350069] [ 6.626] 9: /usr/bin/X (0x7fb5cd293000+0x3d605) [0x7fb5cd2d0605] [ 6.626] 10: /lib/x86_64-linux-gnu/libc.so.6 (__libc_start_main+0xed) [0x7fb5cb44e76d] [ 6.626] 11: /usr/bin/X (0x7fb5cd293000+0x3daad) [0x7fb5cd2d0aad] [ 6.626] Segmentation fault at address 0x14 [ 6.626] Caught signal 11 (Segmentation fault). Server aborting [ 6.626] I'd be very happy if someone can give me a hint on how to configure my ATI card while using the integrated graphics for display. Update I used most of jjhughes57 config and successfully booted the X server on intel (keyboard layout is changed though, funnily). Unfortunately the 2nd X server (fglrx) doesn't fully start. It shuts itself down right after starting [ 6.265] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments [ 6.296] (II) UnloadModule: "mouse" [ 6.296] (II) Unloading mouse [ 6.296] (II) UnloadModule: "kbd" [ 6.296] (II) Unloading kbd [ 6.298] (II) fglrx(0): Shutdown CMMQS [ 6.298] (II) fglrx(0): [uki] removed 1 reserved context for kernel [ 6.298] (II) fglrx(0): [uki] unmapping 8192 bytes of SAREA 0x2000 at 0x7fbef8209000 [ 6.337] (II) fglrx(0): Interrupt handler Shutdown. [ 6.470] ddxSigGiveUp: Closing log [ 6.470] Server terminated successfully (0). Closing log file. Thanks for any hints what is wrong here.

  Read the article

• Laptop turning off when fan is spinning hard

  - by Ieyasu Sawada

  My laptop seems to have reach its lifespan. Its an Acer laptop so I guess that's normal. But I'd like to hear your opinions about this. My laptop is only 2 years old. I haven't heard the fan spinning like crazy not until these past 5 months. What I did: Hoping that its just the applications that I have installed that's consume the life of my laptop from the background. I used PC Decrapifier to uninstall some of the things that I don't need. Reformatted my computer but only the primary partition since my files are on the second partition. Bought a cooling pad. None of these works. I noticed the fan spins so hard when: I have a lot of browser tabs open. Full screen mode a flash video that I'm viewing online. Using VLC to watch encoded videos. There's this thing called minicoder http://sourceforge.net/projects/minicoder/ to reduce the size of videos without affecting much of the quality. I'm suspecting that it needs additional software(to make life easier for the hardware) even though the video is working fine in VLC. VLC consumes about 300,000K and above(as seen from task manager) while watching videos (.mkv). The problem: Laptop suddenly turns off when the fan spins like crazy for about 20 minutes. I'm always checking to see if its already too hot(using my fingers to feel the side of the laptop) but its not so I continued watching and then poof! computer turns off. Laptop won't turn on immediately when I turn it on after it turning off by itself. The light for the power goes on but its turns off immediately. I have to wait for about 10-20 seconds before it boots up without problems. So how do I go about this? Is this just normal for Acer laptops after about 2 years of heavy usage (8-12 hours a day)? My usage is heavy but I normally only have a text-editor(sublime) and browser open(chrome). Here's what I got from HW monitor:

  Read the article

• Unable to load type error in ASP.NET 4 application on Windows Server 2003 / IIS6 -- only happens after first worker process recycle

  - by Daniel Coffman

  I'm running an ASP.NET 4.0 web application on IIS6 (Windows Server 2003 x64). This app is one of many running on this server under the Default Web Site -- but is alone on it's own application pool because the other sites are all running ASP.NET 2.0 still. When I deploy my application, it works just fine until the application pool recycles or kills its worker process (by default 2 hours or 20 minutes with no activity). After this, I get the error: "Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information. System.Reflection.ReflectionTypeLoadException: Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information." Refreshing the page, recycling the application pool, and iisreset do nothing. But, I can bring the site back online again for a little while by simply redeploying it. The stack trace seems to start at an EntityDataSource -- see below: [ReflectionTypeLoadException: Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information.] System.Reflection.RuntimeModule.GetTypes(RuntimeModule module) +0 System.Reflection.Assembly.GetTypes() +144 System.Data.Metadata.Edm.ObjectItemConventionAssemblyLoader.LoadTypesFromAssembly() +45 System.Data.Metadata.Edm.ObjectItemAssemblyLoader.Load() +34 System.Data.Metadata.Edm.AssemblyCache.LoadAssembly(Assembly assembly, Boolean loadReferencedAssemblies, ObjectItemLoadingSessionData loadingData) +130 System.Data.Metadata.Edm.AssemblyCache.LoadAssembly(Assembly assembly, Boolean loadReferencedAssemblies, KnownAssembliesSet knownAssemblies, EdmItemCollection edmItemCollection, Action`1 logLoadMessage, Object& loaderCookie, Dictionary`2& typesInLoading, List`1& errors) +248 System.Data.Metadata.Edm.ObjectItemCollection.LoadAssemblyFromCache(ObjectItemCollection objectItemCollection, Assembly assembly, Boolean loadReferencedAssemblies, EdmItemCollection edmItemCollection, Action`1 logLoadMessage) +580 System.Data.Metadata.Edm.ObjectItemCollection.ExplicitLoadFromAssembly(Assembly assembly, EdmItemCollection edmItemCollection, Action`1 logLoadMessage) +193 System.Data.Metadata.Edm.MetadataWorkspace.ExplicitLoadFromAssembly(Assembly assembly, ObjectItemCollection collection, Action`1 logLoadMessage) +140 System.Web.UI.WebControls.EntityDataSourceView.ConstructContext() +756 System.Web.UI.WebControls.EntityDataSourceView.ExecuteSelect(DataSourceSelectArguments arguments) +147 This is a bug filed for the same (or similar) problem: http://connect.microsoft.com/VisualStudio/feedback/details/541962/unable-to-load-one-or-more-of-the-requested-types-connected-with-entitydatasource Question: Has anyone seen this and have advice? I've tried copy-local on all the references... Works just fine on my dev machine. Works on the server until the application pool worker process recycles. I'm building in release mode, but experience the same result when I build for debug. I'm stumped.

  Read the article

• Port forwarding using a BT Home Hub 2.0 (Supplied to new BT Infinity Customers in the UK)

  - by Jasarien

  I don't usually have trouble with port forwarding, I've been able to do it successfully on a number of different routers, including Linksys, Belkin, Netgear and Apple (Time Capsule / Airport Extreme). So I'm quite confused here. I had been using my Apple Time Capsule as my router for a few years now, with several port mappings all working fine. But it died recently, so I've had to resort to using the BT Home Hub 2.0 that was supplied with my BT Infinity broadband subscription. The forwarding interface for the Home Hub is simplified for the most part, allowing you to select an application or game and assign it to a particular computer on the network which you choose from a list that the Home Hub has 'discovered'. My Mac Pro has a manually assigned static IP 192.168.1.4 and my router is static at 192.168.1. I have chosen SSH from the list of applications and assigned it to my Mac Pro (the only computer in the list currently). The Home Hub also has a feature to keep a DNS service updated, and I have set it to keep my external IP address updated on my hostname. This is how I had it setup in the past with other routers and not had trouble before. I am able to ping my hostname (and external IP) from outside the network and get a response. But when I try to connect using SSH, the connection times out. The Home Hub also has "Firewall settings". The currently selected setting is: Default: Allow all outgoing connections and block all incoming traffic. Games and application sharing is allowed. But I've tried changing it to: Disabled: All traffic is allowed to pass through your BT Home Hub to your devices. Note: you’ll still need to use the games and application sharing feature to make sure that certain applications work properly. And the connection still times out... So frustrating. The OS X firewall on my Mac is disabled, so I don't think that's in the way. I have tried setting the port forwarding manually, instead of relying on the preset "SSH" option (incase it's not using the port I expect). So I set up my own "application" (as the Home Hub calls it) and forwarded external port 22 TCP to internal port 22 TCP to 192.168.1.4 - but that just gives the same result - unable to connect. Next, with the router's firewall disabled and OS X's firewall disabled, I ran the Shields Up test (https://www.grc.com/x/ne.dll?bh0bkyd2) and the result was that all my service ports (0 - 1055) are in 'Stealth' mode. I.e. nothing even exists at my IP as far as any outsider is concerned... Strange. The only thing that seems to work is setting my Mac Pro as the DMZ - which I don't want to do for obvious reasons. Any help with this would be extremely appreciated, thanks.

  Read the article

• Why many applications close after opening a document or doing a specific actions?

  - by Mohsen Farjami

  I have some encrypted pdf files that have no problem and in my last windows, I could open them easily with Adobe Reader 9.2 and other pdf readers. But now, I can only open non-encrypted pdf files and one encrypted file with Adobe Reader. every time I open almost any encrypted pdf, it closes itself. Also, when I try to search a folder for a keyword with Foxit Reader, once it closed. This is not related to Adobe Reader, because I have the same problem with Word 2007. When I open a document, sometimes it closes instantly and sometimes it closes after a few seconds and sometimes it is stable. My windows is Fresh. I have installed it a few days ago. I have ESET Smart Security 5.2 and I have updated it today. OS: XP Pro SP3, RAM: 3 GB, CPU: 2 GHZ, HDD: 320 GB My installed applications: Adobe AIR Adobe Flash Player 11 ActiveX Adobe Flash Player 11 Plugin Adobe Photoshop CS4 Adobe Reader 9.2 Atheros Wireless LAN Client Adapter Babylon Bluetooth Stack for Windows by Toshiba CCleaner Conexant HD Audio Dell Touchpad ESET Smart Security Farsi (101) Custom Foxit Reader Framing Studio 3.27 Google Chrome Hard Disk Sentinel PRO HDAUDIO Soft Data Fax Modem with SmartCP Intel(R) Graphics Media Accelerator Driver IrfanView (remove only) Java(TM) 6 Update 18 K-Lite Mega Codec Pack 8.8.0 Microsoft .NET Framework 2.0 Service Pack 1 Microsoft .NET Framework 3.0 Service Pack 1 Microsoft .NET Framework 3.5 Microsoft Data Access Components KB870669 Microsoft Office 2007 Primary Interop Assemblies Microsoft Office Enterprise 2007 Microsoft User-Mode Driver Framework Feature Pack 1.0.0 (Pre-Release 5348) Mozilla Firefox 7.0.1 (x86 en-US) Notepad++ Office Tab FreeEdition 8.50 ParsQuran PerfectDisk 12 Professional Registry First Aid RICOH R5C83x/84x Flash Media Controller Driver Ver.3.54.06 Sahar Money Manager 2.5 Stickies 7.1d The KMPlayer (remove only) TurboLaunch 5.1.2 Unlocker 1.9.1 USB Safely Remove 4.2 Virastyar Visual Studio 2005 Tools for Office Second Edition Runtime Winamp Windows Internet Explorer 8 Windows Media Player 11.0.5358.4826 Windows XP Service Pack 3 WinRAR 4.11 (32-bit) WorkPause 1.2 Z Dictionary My startup applications: WorkPause USB Safely Remove TurboLaunch SunJavaUpdateSched Stickies rfagent Persistence ParsQuran Daily Verse ITSecMng IgfxTray HotKeysCmds Hard Disk Sentinel egui disable shift+delete CTFMON.EXE Bluetooth Manager Babylon Client Apoint AdobeCS4ServiceManager Adobe Reader Speed Launcher Adobe ARM What should I do to solve it? If you recommend installing Windows again, what guarantees that it won't happen again?

  Read the article

• Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

  - by Pro Backup

  In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

  Read the article

• Why is my mdadm raid-1 recovery so slow?

  - by dimmer

  On a system I'm running Ubuntu 10.04. My raid-1 restore started out fast but quickly became ridiculously slow (at this rate the restore will take 150 days!): dimmer@paimon:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdc1[2] sdb1[1] 1953513408 blocks [2/1] [_U] [====>................] recovery = 24.4% (477497344/1953513408) finish=217368.0min speed=113K/sec unused devices: <none> Eventhough I have set the kernel variables to reasonably quick values: dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_min 1000000 dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_max 100000000 I am using 2 2.0TB Western Digital Hard Disks, WDC WD20EARS-00M and WDC WD20EARS-00J. I believe they have been partitioned such that their sectors are aligned. dimmer@paimon:/sys$ sudo parted /dev/sdb GNU Parted 2.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00M (scsi) Disk /dev/sdb: 2000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 (parted) unit s (parted) p Number Start End Size File system Name Flags 1 2048s 3907028991s 3907026944s ext4 (parted) q dimmer@paimon:/sys$ sudo parted /dev/sdc GNU Parted 2.2 Using /dev/sdc Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00J (scsi) Disk /dev/sdc: 2000GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 I am beginning to think that I have a hardware problem, otherwise I can't imagine why the mdadm restore should be so slow. I have done a benchmark on /dev/sdc using Ubuntu's disk utility GUI app, and the results looked normal so I know that sdc has the capability to write faster than this. I also had the same problem on a similar WD drive that I RMAd because of bad sectors. I suppose it's possible they sent me a replacement with bad sectors too, although there are no SMART values showing them yet. Any ideas? Thanks. As requested, output of top sorted by cpu usage (notice there is ~0 cpu usage). iowait is also zero which seems strange: top - 11:35:13 up 2 days, 9:40, 3 users, load average: 2.87, 2.58, 2.30 Tasks: 142 total, 1 running, 141 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.2%sy, 0.0%ni, 99.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3096304k total, 1482164k used, 1614140k free, 617672k buffers Swap: 1526132k total, 0k used, 1526132k free, 535416k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 45 root 20 0 0 0 0 S 0 0.0 2:17.02 scsi_eh_0 1 root 20 0 2808 1752 1204 S 0 0.1 0:00.46 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.17 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/1 ... dmesg errors, definitely looking like hardware: [202884.000157] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [202884.007015] ata5.00: failed command: FLUSH CACHE EXT [202884.013728] ata5.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [202884.013730] res 40/00:00:ff:59:2e/00:00:35:00:00/e0 Emask 0x4 (timeout) [202884.033667] ata5.00: status: { DRDY } [202884.040329] ata5: hard resetting link [202889.400050] ata5: link is slow to respond, please be patient (ready=0) [202894.048087] ata5: COMRESET failed (errno=-16) [202894.054663] ata5: hard resetting link [202899.412049] ata5: link is slow to respond, please be patient (ready=0) [202904.060107] ata5: COMRESET failed (errno=-16) [202904.066646] ata5: hard resetting link [202905.840056] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [202905.849178] ata5.00: configured for UDMA/133 [202905.849188] ata5: EH complete [203899.000292] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [203899.007096] ata5.00: failed command: IDENTIFY DEVICE [203899.013841] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [203899.013843] res 40/00:00:ff:f9:f6/00:00:38:00:00/e0 Emask 0x4 (timeout) [203899.041232] ata5.00: status: { DRDY } [203899.048133] ata5: hard resetting link [203899.816134] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [203899.826062] ata5.00: configured for UDMA/133 [203899.826079] ata5: EH complete [204375.000200] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204375.007421] ata5.00: failed command: IDENTIFY DEVICE [204375.014799] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204375.014800] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204375.044374] ata5.00: status: { DRDY } [204375.051842] ata5: hard resetting link [204380.408049] ata5: link is slow to respond, please be patient (ready=0) [204384.440076] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204384.449938] ata5.00: configured for UDMA/133 [204384.449955] ata5: EH complete [204395.988135] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204395.988140] ata5.00: failed command: IDENTIFY DEVICE [204395.988147] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204395.988149] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204395.988151] ata5.00: status: { DRDY } [204395.988156] ata5: hard resetting link [204399.320075] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204399.330487] ata5.00: configured for UDMA/133 [204399.330503] ata5: EH complete

  Read the article

• Ubuntu 12.04 crash analysis - strange binary data on all open files at the moment of crash

  - by lanbo

  A couple of hours ago we got a system crash on Ubuntu 12.04. We checked all the log files and there is nothing suspicious to blame to. Last stuff that was logged was some dovecot activity. There are no kernel panic messages. Nothing. It is a new server (new hardware) we are testing before production. And because it is new hard, I'm suspicious the problem may be due to some faulty hardware. We already run memtester with no problem detected. I'll be happy to hear from other hardware testing tools (the machine has SSD). Anyway, the thing I wanted to ask you is a different one. The strange thing is on every open file at the moment of the crash we found the next sequence of symbols was written into them: "@^@^@^@^@^@^@...". For example, on the syslog log file we got: Apr 16 15:53:56 odyssey dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<info>, method=PLAIN, rip=46.29.255.73, lip=5.9.58.177 ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^ [these continues for about 1000 chars...] ^@^@^@^@Apr 16 15:55:12 odyssey kernel: imklog 5.8.6, log source = /proc/kmsg started. We got all these symbols in all open files. These include: syslog, mail.log, kern.log, ... But also on some logs that are output by php scripts run in CRONs from user accounts (not root). So, any idea why all open files got these characters written during the crash? This is pretty bad since the crash corrupted many files (we don't even know which other ones may be affected). We are suspicious that all open files (in write mode maybe) at the moment of the crash got all these symbols inserted. Why is that? BTW [in case it helps], the system automatically rebooted after the crash but Apache did not start. There were not traces in /var/apache2/*log why apache did not start. After running a "service apache2 start" it started with no problems. Also, we rebooted the machine manually and Apache also started on reboot. But it did not start after the crash and no errors were reported. Thanks guys!

  Read the article

• How do I troubleshoot an IPsec tunnel (from a cellular router to a public server)?

  - by Hanno Fietz

  I'm new to IPsec and struggling with a setup that might soon be widely used in our operations (provided I do understand it, eventually...). A cellular router (blackbox by netModule, from its log messages it seems to be running Linux and OpenSwan) connects a sensor network on customers' sites with our public server. We need to be able to connect into the local network, so I had the cell provider give me a public IP (a dynamic one). The way their setup works, the public IPs only allow IPsec traffic. I set up OpenSwan on our Ubuntu server (running Jaunty). This is my connection config from /etc/ipsec.conf: conn gprs-field-devices left=my.pub.lic.ip [email protected] #leftsubnet=192.168.1.129/25 right=%any [email protected] #rightsubnet=192.168.1.1/25 #rightnexthop=%defaultroute auto=add On the router, all I have is the Web UI, in which I made the following settings: "Remote endpoint": public IP of server, same as "left" above "Local Network Address": 192.168.1.1 "Local Network Mask": 255.255.255.128 "Remote Network Address": 192.168.1.129 "Remote Network Mask": 255.255.255.128 The pluto process on the server is listening for connections on port 500. It can't open a tunnel, obviously, because it doesn't know at which IP the client is. I set up a passphrase as PSK for @field.econemon.com in /etc/ipsec.secrets and also configured it in the router (which doesn't seem to support certificates). My problem is, nothing happens. The router just says, IPsec is "down". When I copy-paste the IP into ipsec.conf (for "right="), and ask the server to ipsec auto --up gprs-field-devices, it just hangs until I press Ctrl-C. Is there anything wrong with my setup? How can I debug this further? My router gives the following loglines that seem related, but don't tell me anything: Feb 21 23:08:20 Netbox authpriv.warn pluto[2497]: loading secrets from "/etc/ipsec.secrets" Feb 21 23:08:20 Netbox authpriv.warn pluto[2497]: loading secrets from "/etc/ipsec.d/hostkey.secrets" Feb 21 23:08:20 Netbox authpriv.warn pluto[2497]: loading secrets from "/etc/ipsec.d/netbox0.secrets" Feb 21 23:08:20 Netbox authpriv.warn pluto[2497]: "netbox00" #1: initiating Main Mode Feb 21 23:08:20 Netbox daemon.err ipsec__plutorun: 104 "netbox00" #1: STATE_MAIN_I1: initiate Feb 21 23:08:20 Netbox daemon.err ipsec__plutorun: ...could not start conn "netbox00" Feb 21 23:08:22 Netbox authpriv.warn pluto[2497]: packet from 188.40.57.4:500: ignoring informational payload, type NO_PROPOSAL_CHOSEN Feb 21 23:08:22 Netbox authpriv.warn pluto[2497]: packet from 188.40.57.4:500: received and ignored informational message Feb 21 23:08:28 Netbox user.warn parrot.system_controller[762]: IPSECCTRLR: Tunnel 0 is down for 0 seconds Feb 21 23:08:40 Netbox user.warn parrot.system_controller[762]: IPSECCTRLR: Tunnel 0 is down for 10 seconds Feb 21 23:08:52 Netbox authpriv.warn pluto[2497]: packet from 188.40.57.4:500: ignoring informational payload, type NO_PROPOSAL_CHOSEN

  Read the article

• Corosync :: Restarting some resources after Lan connectivity issue

  - by moebius_eye

  I am currently looking into corosync to build a two-node cluster. So, I've got it working fine, and it does what I want to do, which is: Lost connectivity between the two nodes gives the first node '10node' both Failover Wan IPs. (aka resources WanCluster100 and WanCluster101 ) '11node' does nothing. He "thinks" he still has his Failover Wan IP. (aka WanCluster101) But it doesn't do this: '11node' should restart the WanCluster101 resource when the connectivity with the other node is back. This is to prevent a condition where node10 simply dies (and thus does not get 11node's Failover Wan IP), resulting in a situation where none of the nodes have 10node's failover IP because 10node is down 11node has "given back" his failover Wan IP. Here's the current configuration I'm working on. node 10sch \ attributes standby="off" node 11sch \ attributes standby="off" primitive LanCluster100 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.100" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive LanCluster101 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.101" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive Ping100 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive Ping101 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive WanCluster100 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.100" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive WanCluster101 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.101" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive Website0 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf" options="-DSSL" \ operations $id="Website-one" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" primitive Website1 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf.1" options="-DSSL" \ operations $id="Website-two" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" group All100 WanCluster100 LanCluster100 group All101 WanCluster101 LanCluster101 location AlwaysPing100WithNode10 Ping100 \ rule $id="AlWaysPing100WithNode10-rule" inf: #uname eq 10sch location AlwaysPing101WithNode11 Ping101 \ rule $id="AlWaysPing101WithNode11-rule" inf: #uname eq 11sch location NeverLan100WithNode11 LanCluster100 \ rule $id="RAND1083308" -inf: #uname eq 11sch location NeverPing100WithNode11 Ping100 \ rule $id="NeverPing100WithNode11-rule" -inf: #uname eq 11sch location NeverPing101WithNode10 Ping101 \ rule $id="NeverPing101WithNode10-rule" -inf: #uname eq 10sch location Website0NeedsConnectivity Website0 \ rule $id="Website0NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 location Website1NeedsConnectivity Website1 \ rule $id="Website1NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 colocation Never -inf: LanCluster101 LanCluster100 colocation Never2 -inf: WanCluster100 LanCluster101 colocation NeverBothWebsitesTogether -inf: Website0 Website1 property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1408954702" \ maintenance-mode="false" rsc_defaults $id="rsc-options" \ resource-stickiness="100" \ migration-threshold="3" I also have a less important question concerning this line: colocation NeverBothLans -inf: LanCluster101 LanCluster100 How do I tell it that this collocation only applies to '11node'.

  Read the article

• Postfix to deliver mail to a virtual address mailbox

  - by Chloe

  Postfix version 2.6.6, Dovecot Version 2.0.9 I want to setup Postfix + Dovecot. Dovecot seems to be working. I can authenticate. However, the mailbox is empty! Nothing will get delivered! I followed many tutorials on Postfix + Dovecot but they seem to want to complicate things by using Dovecot LDA or MySQL. I just want it to be very simple and having Postfix deliver to the virtual mail boxes are fine. I don't need MySQL either. I already set up a custom password file that Dovecot uses for authentication and I can login to POP3 with SSL. I can see from the logs that Postfix is delivering to the system user accounts (the catch-all), instead of the virtual users that I set up in Dovecot. The SMTP + SSL authentication seems to work also. I can also see from the logs that Dovecot is checking the correct virtual mail folder. I just need to figure out how to get Postfix to deliver to the virtual mail boxes. I have the following which I believe are relevant. Let me know what other settings you need to see: alias_maps = hash:/etc/aliases mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain mydomain = xxx.com myhostname = mail.xxx.com mynetworks = 99.99.99.99, 99.99.99.99 myorigin = $mydomain relay_domains = $mydestination, xxx.com, domain2.net, domain3.com sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = reject_non_fqdn_sender reject_non_fqdn_recipient reject_unknown_recipient_domain permit_sasl_authenticated check_relay_domains smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_type = dovecot smtpd_sender_restrictions = check_sender_mx_access cidr:/etc/postfix/bogus_mx reject_invalid_hostname reject_unknown_sender_domain reject_non_fqdn_sender virtual_mailbox_base = /var/spool/vmail virtual_mailbox_domains = xxx.com, domain2.net, domain3.com virtual_minimum_uid = 444 Postfix master.cf: submission inet n - - - - smtpd -o smtpd_tls_security_level=encrypt -o smtpd_sasl_auth_enable=yes -o smtpd_sasl_type=dovecot -o smtpd_sasl_path=private/auth -o smtpd_sasl_security_options=noanonymous -o smtpd_sasl_local_domain=$myhostname -o smtpd_client_restrictions=permit_sasl_authenticated,reject -o smtpd_sender_login_maps=hash:/etc/postfix/virtual -o smtpd_sender_restrictions=reject_sender_login_mismatch -o smtpd_recipient_restrictions=reject_non_fqdn_recipient,reject_unknown_recipient_domain,permit_sasl_authenticated,reject Dovecot related: mail_location = maildir:~/Maildir passdb { args = /etc/dovecot/users.conf driver = passwd-file } service auth { unix_listener /var/spool/postfix/private/auth { mode = 0660 user = postfix } } The virtual mail user: vmail:x:444:99:virtual mail users:/var/spool/vmail:/sbin/nologin Here is the /var/log/maillog when I try to send something to myself: Oct 25 22:10:05 308321 postfix/smtpd[2200]: connect from user-999.cable.mindspring.com[99.99.99.99] Oct 25 22:10:05 308321 postfix/smtpd[2200]: D224BD4753: client=user-999.cable.mindspring.com[99.99.99.99], sasl_method=LOGIN, [email protected] Oct 25 22:10:06 308321 postfix/cleanup[2207]: D224BD4753: message-id=<7DC3C163CFFC483AB6226F8D3D9969D2@dumbopc> Oct 25 22:10:06 308321 postfix/qmgr[2168]: D224BD4753: from=<[email protected]>, size=1385, nrcpt=1 (queue active) Oct 25 22:10:06 308321 postfix/smtpd[2200]: disconnect from user-999.cable.mindspring.com[99.99.99.99] Oct 25 22:10:06 308321 postfix/local[2208]: D224BD4753: to=<[email protected]>, orig_to=<[email protected]>, relay=local, delay=1.1, delays=0.53/0.02/0/0.51, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 22:10:06 308321 postfix/qmgr[2168]: D224BD4753: removed

  Read the article

• How to get an inactive RAID device working again?

  - by Jonik

  After booting, my RAID1 device (/dev/md_d0 *) sometimes goes in some funny state and I cannot mount it. * Originally I created /dev/md0 but it has somehow changed itself into /dev/md_d0. # mount /opt mount: wrong fs type, bad option, bad superblock on /dev/md_d0, missing codepage or helper program, or other error (could this be the IDE device where you in fact use ide-scsi so that sr0 or sda or so is needed?) In some cases useful info is found in syslog - try dmesg | tail or so The RAID device appears to be inactive somehow: # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d0 : inactive sda4[0](S) 241095104 blocks # mdadm --detail /dev/md_d0 mdadm: md device /dev/md_d0 does not appear to be active. Question is, how to make the device active again (using mdmadm, I presume)? (Other times it's alright (active) after boot, and I can mount it manually without problems. But it still won't mount automatically even though I have it in /etc/fstab: /dev/md_d0 /opt ext4 defaults 0 0 So a bonus question: what should I do to make the RAID device automatically mount at /opt at boot time?) This is an Ubuntu 9.10 workstation. Background info about my RAID setup in this question. Edit: My /etc/mdadm/mdadm.conf looks like this. I've never touched this file, at least by hand. # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR <my mail address> # definitions of existing MD arrays # This file was auto-generated on Wed, 27 Jan 2010 17:14:36 +0200 In /proc/partitions the last entry is md_d0 at least now, after reboot, when the device happens to be active again. (I'm not sure if it would be the same when it's inactive.) Resolution: as Jimmy Hedman suggested, I took the output of mdadm --examine --scan: ARRAY /dev/md0 level=raid1 num-devices=2 UUID=de8fbd92[...] and added it in /etc/mdadm/mdadm.conf, which seems to have fixed the main problem. After changing /etc/fstab to use /dev/md0 again (instead of /dev/md_d0), the RAID device also gets automatically mounted!

  Read the article

• Google Chrome issues

  - by Ben Hooper

  I'm an avid user of Chrome and would defend it to the death but there is no denying that it has issues, and I've been experiencing a lot of them recently. Issues Stuck tabs Issue: Around 60% of the time (higher when the system has just started), when Chrome is launched, some or all of the pinned tabs and startup pages will get stuck in the counter-clockwise-rotating "contacting server" mode and never snap out of it. Fix: Quit and launch Chrome until they load properly (this really isn't good, as quitting and launching Chrome can and has cleared all pinned tabs). Extra Information: If you stop the loading and re-enter the URL then the page will load perfectly. The amount of pinned tabs or startup pages seems to be irrelevant, but I could be wrong.   "Downloaded/out of" Issue: Each item in the download bar has a downloaded status section, formatted as "downloaded/out of". Sometimes Chrome doesn't display the "out of" part.   Collapsed settings windows Issue: In Chrome version 19(ish)+, settings are configured via overlayed / popup windows. Sometimes, the window will open fully collapsed. Fix: Resize Chrome's window or open the developer tools. "Network Error" with large downloads Issue: Sometimes, when downloading large files (500MB+) Chrome will download the entire file, the download status will freeze (for example, "1 GB/1 GB") for a few minutes, report "Network error", and delete the .crdownload file. Extra Information: The same file from the same website on the same computer downloads perfectly in other browsers. The website and file type seem to be irrelevant.   Information: I've experienced some of these issues on my home PC and some on my work PC, both of which are Windows 7 Ultimate x64. The only things that link them are my Google account (all settings are synced). Updating Chrome hasn't worked. Most of these issues presented themselves around about version 17 and have continued right through to 21 (current). Uninstalling Chrome, deleting all data in %programFiles(x86)%\Google and %localAppData%\Google, and reinstalling hasn't worked. I have yet to see whether disabling all extensions would make a difference, but it's hard to diagnose as these issues don't occur 100% of the time.   In my case, I don't know if there's an actual solution. I'm just curious as to whether anyone else is having similar issues to those that I'm experiencing. At least then I'll know it's an issue with Chrome itself.

  Read the article

• How to specify this 'symbolic link' for the Jungo WinDriver?

  - by user252098

  Just now , I try to install the Jungo WinDriver in the Ubuntu 13.10 . But I am puzzled by the its manual : 4.2.3. Linux WinDriver Installation Instructions 4.2.3.1. Preparing the System for Installation In Linux, kernel modules must be compiled with the same header files that the kernel itself was compiled with. Since WinDriver installs kernel modules, it must compile with the header files of the Linux kernel during the installation process. Therefore, before you install WinDriver for Linux, verify that the Linux source code and the file version.h are installed on your machine: Install the Linux kernel source code: If you have yet to install Linux, install it, including the kernel source code, by following the instructions for your Linux distribution. If Linux is already installed on your machine, check whether the Linux source code was installed. You can do this by looking for 'linux' in the /usr/src directory. If the source code is not installed, either install it, or reinstall Linux with the source code, by following the instructions for your Linux distribution. Install version.h: The file version.h is created when you first compile the Linux kernel source code. Some distributions provide a compiled kernel without the file version.h. Look under /usr/src/linux/include/linux to see whether you have this file. If you do not, follow these steps: Become super user: $ su Change directory to the Linux source directory: cd /usr/src/linux Type: make xconfig Save the configuration by choosing Save and Exit. Type: make dep Exit super user mode: exit To run GUI WinDriver applications (e.g., DriverWizard [5]; Debug Monitor [7.2]) you must also have version 5.0 of the libstdc++ library — libstdc++.so.5. If you do not have this file, install it from the relevant RPM in your Linux distribution (e.g., compat-libstdc++). Before proceeding with the installation, you must also make sure that you have a linux symbolic link. If you do not, create one by typing /usr/src$ ln -s 'target kernel'/linux For example, for the Linux 2.4 kernel type /usr/src$ ln -s linux-2.4/ linux ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ I can't understand how to specify these two parameters in my Ubuntu .

  Read the article

• Hang while starting several daemons

  - by Adrian Lang

  I’m running a Debian Squeeze AMD64 server. Target runlevel after boot is runlevel 2, which includes rsyslogd, cron, sshd and some other stuff, but not dovecot, postfix, apache2, etc. The system fails to reach runlevel 2 with several symptoms: The system hangs at trying to start rsyslogd Booting into runlevel 1 works, then login from the console works Starting rsyslogd from runlevel 1 via /etc/init.d/rsyslog hangs Starting runlevel 2 with rsyslogd disabled works But then, logging in via console fails: I get the motd, and then nothing Starting sshd from runlevel 1 succeeds But then, I cannot login via ssh. Sometimes password ssh login gives me the motd and then nothing, sometimes not even this. Trying to offer a public key seems to annoy the sshd enough to not talk to me any further. When rebooting from runlevel 1, the server hangs at trying to stop apache2 (which is not running, so this really should be trivial). Trying to stop apache2 when logged in in runleve 1 does hang as well. And that’s just the stuff which fails all the time. RAM has been tested, dmesg shows no problems. I have no clue. Update: (shortened) output from rsyslogd -c4 -d called in runlevel 1 rsyslogd 4.6.4 startup, compatibility mode 4, module path '' caller requested object 'net', not found (iRet -3003) Requested to load module 'lmnet' loading module '/user/lib/rsyslog/lmnet.so' module of type 2 being loaded conf.c requested ref for 'lmnet', refcount 1 rsylog runtime initialized, version 4.6.4, current users 1 syslogd.c requested ref for 'lmnet', refcount now 2 I can kill rsyslogd with Strg+C, then. /var/log shows none of the configured log files, though. Update2: Thanks to @DerfK I still have no clue, but at least I narrowed down the problem. I’m now testing with /etc/init.d/apache2 stop (without an apache2 running, of course) which hangs as well and looks like an even more obvious failure. After some testing I found out that a file with one single line: /usr/sbin/apache2ctl configtest /dev/null 2&1 hangs, while the same line executed in an interactive shell works. I was not able to further reduce this line while, i. e. every single part, the stream redirections and the commando itself is necessary to reproduce the hang. @DerfK also pointed me to strace which gave a shallow hint about what kind of hang we have here: wait4(-1for the init scripts futex(0xsomepointer, FUTEX_WAIT_PRIVATE, 2, NULL for rsyslogd / apache2 binaries called by the init scripts The system was installed as a Debian Lenny by my hoster in autumn 2011, I upgraded it to Squeeze immediately and kept it up to date with Squeeze, which then used to be testing. There were no big changes, though. I guess I never tried to reboot the system before.

  Read the article

• Cannot install grub to RAID1 (md0)

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

  Read the article

• Server 2008/Windows 7/Samba Unspecified error 80004005

  - by ancillary

  I have a Samba share on a LAN with 2008 PDC/DNS. Smb authenticates with AD and I have several Win7 Machines that can connect fine. I recently added a couple of new computers to the LAN which were imaged the same way (same software, etc.; different hardware so different drivers) as the other machines and they have the same policies set. I can not get the new machines to connect to the samba share no matter what. I am always met with either Unspecified Error 0x80004005 or Network Path not found. I've turned off the firewall; set LANMAN auth to respond to NTLM only/send LM & NTLM responses/use NTLM session security if negotiated in Local Sec Policy SEcurity Options; tried both ip and hostname to connect. SMB log shows that authentication succeeds; but then connection is immediately killed by the client. tcpdump shows nothing remarkable except that when trying to connect from the client via hostname there is an unknown packet type error: ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) Here's a couple of lines from that error: 11:18:37.964991 IP 001-client.domain.local.49372 > smb.domain.local.netbios-ssn: P 1670:2146(476) ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) [000] AA 46 96 FA D5 99 33 75 0C C4 20 CE 26 42 F3 61 \252F\226\372\325\2313u \014\304 \316&B\363a [010] F0 8C FB 65 18 17 40 A5 DB 42 BB 94 37 53 92 EC \360\214\373e\030\027@\245 \333B\273\2247S\222\354 [020] 55 98 7F C4 AE 3D 6B 10 C4 U\230\177\304\256=k\020 \304 11:18:37.964998 IP smb.domain.local.netbios-ssn > 001-client.domain.local.49372: . ack 2146 win 100 Here's smb.conf just in case (though don't see how if other machines are working fine): [global] workgroup = MYDOMAIN realm = MYDOMAIN.LOCAL server string = domain|smb share interfaces = eth1 security = ADS password server = 192.168.1.3 log level = 2 log file = /var/log/samba/%m.log smb ports = 139 strict locking = no load printers = No local master = No domain master = No wins server = 192.168.1.3 wins support = Yes idmap uid = 500-10000000 idmap gid = 500-10000000 winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes [samba-share1] comment = SMB Share path = /home/share/smb/ valid users = @"MYDOMAIN+Domain Users" admin users = @"MYDOMAIN+Domain Admins" guest ok = no read only = No create mask = 0765 force directory mode = 0777 Any ideas what else I could try or look for? Or what might be the problem? Thanks.

  Read the article

• GPU not powering on

  - by Lerp

  So I got home from work yesterday and went to turn my computer on as per usual to be greeted by this: The screens remained black, so I rebooted; I go as far as GRUB before my screens went black again. I rebooted again, they didn't turn on. I rebooted again, I got as far as the windows login screen. This time I unplugged it, opened it up and cleaned it but to no luck. The GPU was still being tempermental. I repeated the process of turning off and on several times until one time it work as normal. I happily played games for the rest of the night (5-6 hours?) thinking everything was jolly good now. Well I get home from work today and it is doing the SAME thing. Sometimes everything displays normally for a few seconds to minutes then the screens go black; then sometimes the screens don't come on at all. Summary and additional points Screens sometimes turn on before shortly turning off, sometimes they don't; I cannot seem to determine any pattern between when they do or do not turn off. The build has been working fine for about 8 months now so I know it's not hardware incompatibility. If I plug a monitor into the on board graphics I can use the PC normally (just in low graphics mode) I have two monitors and it's a case of they both turn on or not. So I think I can rule out the monitors being dead. I have tried replacing the GPU I have tried replacing the RAM I have tried flashing the CMOS I have tried cleaning the inside The GPU is a Radeon HD 7870 My questions Is my GPU dead? It's not very old and I would rather have a method of being certain it's the GPU before I fork out some money I can't really afford. I do not have a second PC here to test it in. If my GPU is dead why does it sometimes work and sometimes not? Update Okay, it was working again.. at least I thought it was. I left it running for 10-20minutes with the screens black. Turned it off and straight back on and it worked for all of 10minutes. I was then updating the post in joy thinking I could play some games for the rest of the night when BAM it went black again. So yeah, I don't know :C

  Read the article

< Previous Page | 451 452 453 454 455 456 457 458 459 460 461 462  | Next Page >