Search Results

Search found 16640 results on 666 pages for 'computer tower'.

Page 461/666 | < Previous Page | 457 458 459 460 461 462 463 464 465 466 467 468  | Next Page >

• Sound problems in Windows 7

  - by Plastkort

  hi! I hope I reached the correct forum for this question. I have a media computer with a third party audio card (Soundblaster audigy SE) I use a coaxial digital audio cable connected to a Onkyo TX SR508. if I use normal audio, the sound seems very low, I have to set volume atleast to 62 in my amplifier to hear anything, however if I set digital SPDIF I have no means of controlling the audio volume from the PC (only from the amplifier) and this can be nasty if I toggle between movies that uses Digital AC3/THX and movies wihtouth, if I look at movies capable of AC3 the volume gets VERY loud if amp is set to 62, 32 is more than enough volume when using passthrough. so this bothers me is how can I get the same amount of volume with or without digital output? I tried also other soundcards, internal red light Digital audio cable... if I connect to my television I get ok sound on any sound source via HDMI... help :)

  Read the article

• Installed 4GB memory but Windows XP 32 bit only reporting 2GB?

  - by AnthonyWJones

  I've just taken an existing XP Pro 32 bit system that had only 0.5GB of memory installed and maxed it out to 4GB. The BIOS reports the 4GB ram however when XP is booted and I look at the computer properties only 2GB of RAM is reported. Can anyone explain this? Before we go up any blind allys the /3GB switch is not the answer here, I have no need for a single process to use more the 2GB of memory. I'm wondering if the the 32 bit XP Pro is deliberately limited to 2GB. I seem to remember seeing an excellent table on a Microsoft site listing all the various SKUs of Windows and what each one was limited to. However I can't seem to find that table now.

  Read the article

• Office 2007 install limits?

  - by AppsByAaron

  I've been able to install Office 2003 on a couple of computers that I own without any trouble. However, I just got office 2007 and I'm not able to install it on my computer and my laptop. I know this may violate agreements and whatnot but I'm curious to know if this is something that Microsoft has finally started to crack down on or what. Any information is help full. And I know that I'm going to get a few answers telling me that I'm "stealing" or whatever so I don't need to hear about that. thanks. ;)

  Read the article

• What is the minimum delay between two consecutive RS232 frames?

  - by Lord Loh.

  I have been working on creating a UART on an FPGA. I can successfully transmit and receive single characters typed on PuTTY. However, when I set my FPGA to constantly write a large sequences of "A", sometimes I end up with a sequences of "@" or some other characters until I reset the FPGA a few times. I believe the UART on the computer looses track of the difference between the start bit and a zero. The delay between the two "A" is ~ 30us (measured with a logic analyzer) and the baud rate is 115200 8N1. Is there a minimum delay that must be maintained between two consecutive RS232 frames?

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Mysql Error 2002 (HY000) on Snow Leopard

  - by Ole Media

  My boss update my computer to Snow Leopard, after the update we had a set back and deleted a few files/folders, since then is just nightmare after another one. I finally getting things back but I'm still having problems with MySQL. This is what I did: Deleted ALL of mysql files/folders Download and installed the packages mysql-5.1.45-osx10.6-x86_64.dmg installed the Startup item and the preferences panel After the above, I tried to start MySQL from the preferences panel without luck, and running the following command from Terminal /usr/local/mysql/bin/mysql I get the following result ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/tmp/mysql.sock' (2) I looked at some other post for possible solutions, but what they does not exactly fits my problem, so I cannot find a solution. I'm new to all this and your help will be much appreciated.

  Read the article

• Where does linux look for shared libs?

  - by EsbenP

  I am trying to get the ar command on an embedded ARM computer running linux. I want to install debian and openjdk. It is a headless system. This is a custom linux distribution provided by the hardware manufacturer. The debian installer is missing the ar command so i tried copying the binaries from the debian package, but when running ar I get error while loading shared libraries: libbfd-2.18.0-multiarch.20080103.so: cannot open shared object file: No such file or directory libbfd is also in the package. I tried linking it to /lib and /usr/lib but I get the same message when running. What is the best way to get debian and ar on a custom linux distro?

  Read the article

• Inverted LACK Table Serves as a Perfect Gear Rack [DIY]

  - by Jason Fitzpatrick

  We’ve seen IKEA gear hacked to hold audio and computer gear before, but this mod adds in a simple and effective twist. LACK end tables are, conveniently, the same width as a standard server rack. This makes it super simple for DIYers to mount their gear right into the legs of the table with no modification necessary. In this case, however, Winston Smith included a clever update to the mod. Rather than leave it like a standard table, he flipped the table upside down for increased stability and a stronger connection between the legs of his improvised audio rack and the table-top-turned-floor-plate. He then finished it with a matching LACK shelf piece to serve as a turn-table stand. His gear is stored cleanly, off the floor, and in a sturdy container all for about $25–a definite bargain when it comes to storage racks. Hit up the link below for more information and pictures. LACK Rack & EXPEDIT Desktop [IKEA Hackers] HTG Explains: How Windows Uses The Task Scheduler for System Tasks HTG Explains: Why Do Hard Drives Show the Wrong Capacity in Windows? Java is Insecure and Awful, It’s Time to Disable It, and Here’s How

  Read the article

• The cable of my USB port hub is too short - what to do?

  - by Anna

  Hi, I just bought a new USB port hub "MSY USB 2.0 4-port hub". It has two inputs: A small USB entrance input for external power (?) The problem is that the cable that comes with the hub (small USB on one end, large USB on the other - to input into my computer), is too short for my needs. Is there a solution to this? buying a longer cable might be risky, I know that it might cause problems with power. Is there anything else I can do to make it work? Thanks.

  Read the article

• Data Management Business Continuity Planning

  Business Continuity Governance In order to ensure data continuity for an organization, they need to ensure they know how to handle a data or network emergency because all systems have the potential to fail. Data Continuity Checklist: Disaster Recovery Plan/Policy Backups Redundancy Trained Staff Business Continuity Policies In order to protect data in case of any emergency a company needs to put in place a Disaster recovery plan and policies that can be executed by IT staff to ensure the continuity of the existing data and/or limit the amount of data that is not contiguous.  A disaster recovery plan is a comprehensive statement of consistent actions to be taken before, during and after a disaster, according to Geoffrey H. Wold. He also states that the primary objective of disaster recovery planning is to protect the organization in the event that all or parts of its operations and/or computer services are rendered unusable. Furthermore, companies can mandate through policies that IT must maintain redundant hardware in case of any hardware failures and redundant network connectivity incase the primary internet service provider goes down.  Additionally, they can require that all staff be trained in regards to the Disaster recovery policy to ensure that all parties evolved are knowledgeable to execute the recovery plan. Business Continuity Procedures Business continuity procedure vary from organization to origination, however there are standard procedures that most originations should follow. Standard Business Continuity Procedures Backup and Test Backups to ensure that they work Hire knowledgeable and trainable staff  Offer training on new and existing systems Regularly monitor, test, maintain, and upgrade existing system hardware and applications Maintain redundancy regarding all data, and critical business functionality

  Read the article

• SQL 2008 network logon

  - by gledhilla

  Hi I have a domain controller that I have installed active directory onto and have set up an account that I want to use for my SQL server installation on another computer that is linked onto the domain. I can search for the account in active directory and I am able to select it into the add new user section in MSSMS, however, when I click add I get 'Windows NT user or group 'DOMAIN\user' not found. Check the name again. (Microsoft SQL Server, Error: 15401) I have googled the Error code and I havent found a solution that has fixed the error. If you have any help I would be greatful Thanks :)

  Read the article

• Problem Installing Ubuntu 12.04 - [Errno 5]

  - by Rob Barker

  I'm trying to intall Ubuntu 12.04 to my brand new eBay purchased hard drive. Only got the drive today and already it's causing me problems. The seller is a proper proffesional company with 99.9% positive feedback, so it seems unlikely they would have sold me something rubbish. My old hard drive packed up last Tuesday and so i bought a new one to replace it. Because this was an entirely new drive i decided to install Ubuntu as there was no current operating system. My computer is an eMachines EM250 netbook. There's no disc drive so i am installing from a USB stick. The new operating system loads beautifully, and the desktop appears just as it should. When i click install i am taken to the installer which copies the files to about 35% and then displays this: [Errno 5] Input/output error This is often due to a faulty CD/DVD disk or drive, or a faulty hard disk. It may help to clean the CD/DVD, to burn the CD/DVD at a lower speed, to clean the CD/DVD drive lens (cleaning kits are often available from electronics suppliers), to check whether the hard disk is old and in need of replacement, or to move the system to a cooler environment. The hard drive can be heard constantly crackling. When i booted Ubuntu 12.04 from my old faulty hard drive as a test, i didn't even make it past the purple Ubuntu screen, so it can't be that bad. Any ideas? Message to the moderators. Please do not close this thread. I'm well aware there may be other threads on this, but i don't want it closing as the others do not provide the answer i am looking for. Thank you.

  Read the article

• Gparted: Copy Greyed Out

  - by David

  I booted my system to a gparted linux live CD and I have two partitions: /dev/sda1 /dev/sda2 I want to move both of them to my new physical hard drive (called /dev/sdb). When I right click on /dev/sda1, I can choose copy and then paste it onto /dev/sdb. When I right click on /dev/sda2, copy is greyed out and there is a yellow exclamation point to the left of the disk. I know that the disk works since I can boot my computer from it. Why won't gparted let me copy /dev/sda2 to my new hard disk? Since the option is greyed out, I don't even get an error message. Thanks!

  Read the article

• How would one run a task sequence within a task sequence in SCCM 2012 SP1

  - by BigHomie

  A Shining Example: Inside all of my task sequences I have a group that installs driver packages conditionally based on computer model: And of course, this list does nothing but grow. The fact that it grows isn't a big deal, what is a big deal is that every time it changes I have to manually copy and paste those changes across every task sequence I have, which of course leaves huge room for human error. The same goes for other groups of tasks that are common across task sequences. Looking for a solution where I could centrally manage these tasks, be it link other task sequences to a group within another task sequence, or create a separate task sequence and link to that. I came across a solution by John Marcum (SCCM MVP) that mentioned this ability, but this was a while ago and I can't find the link to it anymore to see if it's even still being updated/maintained, but I'm looking for more of a free solution, or even using Powershell or the ConfigMgr SDK is fine with me, I'm no stranger to either. Update Getting close: http://msdn.microsoft.com/en-us/library/jj217869.aspx

  Read the article

• Cannot ssh anymore into FreeBSD 7.2 home server

  - by Gabi

  Somehow sshd stopped running and no amount of start, restart or onestart will make it go again. I normally ssh into it from a dual-boot laptop computer that shows up on the network as gabi-buntu when running Ubuntu Karmic, and as gabi-pc when running Windows XP Pro. Neither my Putty connection nor the Linux terminal can establish a ssh link anymore. Upon rebooting the server, I am greeted with "/etc/rc: WARNING: run_rc_command: cannot run /usr/sbin/sshd". In addition, a message will appear saying things like rpc.statd: failed to contact host gabi-buntu RPC: port mapper failure RPC: timed out Everything else works fine. The FreeBSD 7.2 box runs a print server, a Samba server, and an Apache server for the home wiki, via https. It also serves up NFS shares for Linux clients. Any suggestions? Thank you, Gabi Huiber

  Read the article

• Internal Website links only working for some users

  - by Ryan

  We are having a very hard time trying to figure out this problem or the root cause. Our website www. countrymusicislove .com is only correctly displaying the homepage for some users. Anytime they click on a post, about me, etc, a 404 error page is displayed. Everything worked fine before we moved over to a new hosting company 2 weeks ago. I am looking for any ideas and even willing to pay someone to troubleshoot and fix this issue as no one seems to have an answer. The entire website is done in the latest version of wordpress. The old website address for the website is http://siteground243.com/~countr10/ And the domain name was registered through google for enom.com Everything is now going through Arvixe.com On my work computer, I am able to get the 404 error to appear on other pages by turning on friendly error messages. When I turn off friendly error messages, everything seems to work. I have tried this several times and it doesn't seem like a coincidence.

  Read the article

• Scheduled task username changed

  - by Ernst

  I posted this originally on stack overflow where I was told I should ask it here: Hi, I created a user on our exchange server, but later changed the username. Now, when I create a scheduled task for that user, and change it's settings (run only when logged on), the username is automatically changed back to the old username. What's causing this and how do I make sure the correct, new username is used for the task (otherwise it won't run), security settings are okay. I did already log in with a different user to delete the profile on the computer and tried again with this user to no avail. The OS is windows xp, the exchange server is on windows server 2003. Thanks

  Read the article

• Ubuntu 12.04 64 bit "unable to find medium with live filesystem" AFTER normal install

  - by user88710

  So, I got a new computer (64 bit quad core yada yada). pulled my Ubuntu SSD drive from old machine, installed it into new machine. (my intention here is to have Ubuntu installed on the 120G SSD, Win7 on the main drive) downloaded 64 bit Ubuntu, burned it to a disk. rebooted with Live CD, installed Ubuntu to the SSD drive, had no problems rebooted again, got the grub menu, selected Ubuntu after a minute i got this - "unable to find medium with live filesystem" booting into windows, explorer doesnt even see the SSD. Device manager sees it though. I assume this is because its formatted with ext4. so, The liveCD saw the SSD just fine, installed fine, but when i try to boot ubuntu, i get the error above, heeellllpppp! UPDATE: small update. Windows did a software update that apparently wiped out my grub, so I guess grub was installed on the main drive. I reinstalled Ubuntu (again) on the SSD drive but, still no joy with booting from it. same error message as above.

  Read the article

• If I exchange the CPU, must I reinstall the OSes? (swapping cpus from one *nix-like to another)

  - by dag729

  Hi, as suggested by the title, I want to change CPU: actually I have two computers, one with Ubuntu running on an AMD Athlon 64 dual core 5200+ and the other with FreeBSD running on an AMD Sempron single core LE-1250. I would like to swap (I am not sure that this is the correct term...) the CPUs from one computer to the other one, that is take the dual core from the ubuntu pc and put it inside the freebsd pc and viceversa. The mobo is the same. Do you think I will encounter problems?

  Read the article

• Unable to install ubuntu on a AMD 64 bit system with a AMD Radeon HD 6670 graphics card

  - by Tom Wingrove

  I’ve been running a dual boot system (Ubuntu/Windows7) for two years or so with no problems. I recently built an AMD 64 Bit System, re-installed Windows but when I went to load Ubuntu inside Windows, hit a snag. The screen view during installation became small square blocks of colour, which obviously is a graphics drive problem. I tried various live disks both 32 & 64 bit for, Ubuntu 12.04, 11.10 & 10.10, all but Ubuntu 10.10 had the same problem. Ubuntu 10.10 loaded ok, installed the presented ATI graphics driver as usual but was left with the AMD Unsupported watermark at the bottom right of the screen. The graphics card installed in the computer is an MSI ATI Radeon HD 6670 (in effect an AMD Radeon HD 6670). I am fairly new to linux and while I can install and tweak the OS, I am rather baffled as to what to do. So my question is will an up to date ATI Driver be released in the near future for installation/live disks? Or am I going to have to downgrade my graphics card to use linux? Yours Tom Wingrove

  Read the article

• Use Port Binding Permissions on Windows

  - by Sharon

  This should be an easy one, but I can't find anything on it. I want to use IIS Express with my local user account to bind to a port on my netbios name. For example, http://computername:1315. My local user account doesn't have permission to do this, but I have administrator access on the machine. Anyone know how to grant permission to my local user account to bind to a port with my computer name instead of localhost? This is on Windows 7.

  Read the article

• Is a ext3 Linux filesystem byte order independent

  - by Lothar

  I have a good old HP-C3700 Workstation with PA-RISC CPU here that I would like to use as a subversion server for a very large repository. I just worry what happens if the workstation dies (everybody who knows this computer knows that it is running like an Abrams tank and unlikely to happen in the next decade). I'm using Debian Linux on this system. If the mainboard dies can I just plug the SCSI drive into a PC and read the files from a normal Intel Linux PC? Which software RAID levels would be safe?

  Read the article

• Is it possible to restrict fileserver access to domain users using computers that are members of the domain?

  - by Chris Madden

  It seems domain isolation can be used to accomplish, but I'd like a solution that doesn't require IPsec, or more accurately, doesn't require IPsec on the fileserver. IPsec if done in software has a large CPU overhead and our NAS boxes don't support any kind of offload. The goal is to avoid authenticated users using non-managed machines to access network resources. Network Access Protection (NAP) and the various enforcement points looked promsiing but I couldn't find a bulletproof way to use them [which doesn't require IPsec on the fileserver]. I was thinking when a domain user accesses the NAS box it will first need a Kerberos ticket from AD, so if AD could somehow verify the computer that was requesting the ticket was in the domain I'd have a solution.

  Read the article

• Installed 4GB memory but Windows XP 32 bit only reporting 2GB?

  - by AnthonyWJones

  I've just taken an existing XP Pro 32 bit system that had only 0.5GB of memory installed and maxed it out to 4GB. The BIOS reports the 4GB ram however when XP is booted and I look at the computer properties only 2GB of RAM is reported. Can anyone explain this? Before we go up any blind allys the /3GB switch is not the answer here, I have no need for a single process to use more the 2GB of memory. I'm wondering if the the 32 bit XP Pro is deliberately limited to 2GB. I seem to remember seeing an excellent table on a Microsoft site listing all the various SKUs of Windows and what each one was limited to. However I can't seem to find that table now.

  Read the article

• Dual External Monitors Through Docking Station on ASUS G73JW-XT1

  - by user60695

  I am getting an ASUS G73JW-XT1; and I would like to set it up so that I can plug it into a docking station at my desk, and use 2 external monitors (not the laptop display and an additional monitor). The computer supports a DVI and HDMI output, but I cannot find any docking stations that will support two external displays, as well as audio ports and USB ports for other peripherals. Does anybody know of a specific docking station that will do this, or another workaround without having to plug in several things to my laptop every time I bring it to my desk?

  Read the article

< Previous Page | 457 458 459 460 461 462 463 464 465 466 467 468  | Next Page >