Search Results

Search found 13576 results on 544 pages for 'mobile dev'.

Page 461/544 | < Previous Page | 457 458 459 460 461 462 463 464 465 466 467 468  | Next Page >

• wifi hardware switch doesn't work on a Dell 1018

  - by user42566

  I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

  Read the article

• Ubuntu 13.04 installation issues: unable to handle kernel paging request error

  - by user173944

  I wish I could say that I’ve done more for the Linux community as of recent but I am very VERY new to all of this and I feel very much in over my head. I figured I would install Ubuntu. on my computer and then I would learn and contribute to the community simultaneously. I will try to be as detailed as I can, please ask questions if you need clarification. I installed Ubuntu. 13.04 (64-bit) on my dell Inspiron 1501. This has an AMD Turion 64-bit TL-56 1.8 Ghz mobile processor. It is a dual core. It has an ATI Radeon Xpress 1150 chipset in it as well. As of right now I only have a total of 2Ghz ram, however I was planning on upgrading that in the near future so I opted for the 64-bit Ubuntu. 13.04. I first tried the live CD and everything seemed to be functioning correctly other than the wireless (but that's not the issue at hand, there are plenty of guides on the internet on how to get that functioning). The internet worked just fine when it was plugged in so no issues there. However, once I went from that to installing 13.04 (just 13.04, no dual partitioning... I want this computer to run strictly Ubuntu.) it did not work. It took me into a shell that I could not type anything into. In this shell it said Bug: unable to handle kernel paging and then it called a bunch of traces and froze up. I had to hard reset the laptop. I tried the boot-repair program multiple times with many different settings and typically after starting up the laptop would say something along the lines of recursive errors. will attempt to fix and then it would attempt to fix a couple of things, and then the computer would freeze up after the text said end trace... so I had to hard reset it again. I'm not an impatient person either, when I say it would freeze up it would be for a period of at least 15 minutes each time before I decided to hard reset. I attempted to install 12.10 on it instead and I got the same exact message, and when I ran boot-repair it did the same exact thing as before. I am currently in the process of running memtest64+ on the computer's memory, though I really don't believe that, nor any of the hardware is at fault due to the fact that it was still running windows vista perfectly when I had decided to switch over to Ubuntu. so far the memtest has came back just fine without any errors, but I’ve only been running it for approximately an hour. So this is the situation I’m in. I did notice when I was using the live disk that the video driver needed updated so I performed that, though I’m fairly certain that has nothing to do with this. I have also attempted (though I’m not certain that my attempt was successful in accomplishing what I had planned) to manually edit the grub settings by making acpi=0 along top of adding nomodeset to the boot commands. Like I said, I’m not sure I did that correctly though, but I’m fairly certain I did. If anyone needs any more information I will be more than happy to provide it, I will post back once I get the full results of the memtest. I very much appreciate any ideas anyone else has, I’ve been at this for a few days to no avail... thank you

  Read the article

• Configure Jenkins and Tomcat using Puppet on Vagrant

  - by ex3v

  I'm playing with setting up my first Spring + jenkins + Tomcat CI dev environment. For now it's just a test/fun phase, but in the near future I'll be starting new project with my coworkers. That's the reason that I want development environment virtualized and exactly te same on every development machine, as well as on production server. I choosen to use Vagrant and to try to write puppet scripts that not only install everything, but also configure everything so each of us will have the same jenkins plugins, same jenkins and tomcat login and password, and literally after calling vagrant up we are ready to work. What I managed to do so far is installation of stuff needed and port forwarding. My vagrantfile looks like this (comments stripped): VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| config.vm.box = "precise32" config.vm.box_url = "http://files.vagrantup.com/precise32.box" config.vm.network :forwarded_port, guest: 80, host: 8090 config.vm.network :forwarded_port, guest: 8080, host: 8091 config.vm.network :private_network, ip: "192.168.33.10" config.vm.provision :puppet do |puppet| puppet.manifests_path = "puppet/" puppet.manifest_file = "default.pp" puppet.options = ['--verbose'] end end And this is my puppet file: Exec { path => [ "/bin/", "/sbin/" , "/usr/bin/", "/usr/sbin/" ] } class system-update { exec { 'apt-get update': command => 'apt-get update', } $sysPackages = [ "build-essential" ] package { $sysPackages: ensure => "installed", require => Exec['apt-get update'], } } class tomcat { package { "tomcat": ensure => present, require => Class["system-update"], } service { "tomcat": ensure => "running", require => Package["tomcat"], } } class jenkins { package { "jenkins": ensure => present, require => Class["system-update"], } service { "jenkins": ensure => "running", require => Package["jenkins"], } } include system-update include tomcat include jenkins Now, when I hit vagrant provision and go to http://localhost:8091/ I can see jenkins running, so above script works good. Next step is configurating jenkins and tomcat by extending above puppet scripts. I'm pretty green when it comes to CI. After wandering around web I've found few tutorials about jenkins configuration (here's one of them). I really want to move configuration presented in this tutorial to puppet file, so when I spread my vagrantfile and puppet file between my coworkers, I will be sure that everyone has exactly te same setup. Unfortunately I'm also green about using puppet, I don't know how to do this. Any help will be apreciated.

  Read the article

• Why Ultra-Low Power Computing Will Change Everything

  - by Tori Wieldt

  The ARM TechCon keynote "Why Ultra-Low Power Computing Will Change Everything" was anything but low-powered. The speaker, Dr. Johnathan Koomey, knows his subject: he is a Consulting Professor at Stanford University, worked for more than two decades at Lawrence Berkeley National Laboratory, and has been a visiting professor at Stanford University, Yale University, and UC Berkeley's Energy and Resources Group. His current focus is creating a standard (computations per kilowatt hour) and measuring computer energy consumption over time. The trends are impressive: energy consumption has halved every 1.5 years for the last 60 years. Battery life has made roughly a 10x improvement each decade since 1960. It's these improvements that have made laptops and cell phones possible. What does the future hold? Dr. Koomey said that in the past, the race by chip manufacturers was to create the fastest computer, but the priorities have now changed. New computers are tiny, smart, connected and cheap. "You can't underestimate the importance of a shift in industry focus from raw performance to power efficiency for mobile devices," he said. There is also a confluence of trends in computing, communications, sensors, and controls. The challenge is how to reduce the power requirements for these tiny devices. Alternate sources of power that are being explored are light, heat, motion, and even blood sugar. The University of Michigan has produced a miniature sensor that harnesses solar energy and could last for years without needing to be replaced. Also, the University of Washington has created a sensor that scavenges power from existing radio and TV signals.Specific devices designed for a purpose are much more efficient than general purpose computers. With all these sensors, instead of big data, developers should focus on nano-data, personalized information that will adjust the lights in a room, a machine, a variable sign, etc.Dr. Koomey showed some examples:The Proteus Digital Health Feedback System, an ingestible sensor that transmits when a patient has taken their medicine and is powered by their stomach juices. (Gives "powered by you" a whole new meaning!) Streetline Parking Systems, that provide real-time data about available parking spaces. The information can be sent to your phone or update parking signs around the city to point to areas with available spaces. Less driving around looking for parking spaces!The BigBelly trash system that uses solar power, compacts trash, and sends a text message when it is full. This dramatically reduces the number of times a truck has to come to pick up trash, freeing up resources and slashing fuel costs. This is a classic example of the efficiency of moving "bits not atoms." But researchers are approaching the physical limits of sensors, Dr. Kommey explained. With the current rate of technology improvement, they'll reach the three-atom transistor by 2041. Once they hit that wall, it will force a revolution they way we do computing. But wait, researchers at Purdue University and the University of New South Wales are both working on a reliable one-atom transistors! Other researchers are working on "approximate computing" that will reduce computing requirements drastically. So it's unclear where the wall actually is. In the meantime, as Dr. Koomey promised, ultra-low power computing will change everything.

  Read the article

• Stuck with Documentum Still? Do MORE with Oracle WebCenter!

  - by Michael Snow

  WEBCAST TODAY!! 03/22/12 Do you need to lower costs? Raise Productivity? Foster Innovation? Improve Online Engagement? But you’re still stuck with Documentum? Step away from the ledge – there is hope – let us help you. Top 4 Content Imperatives · Lower Costs - Reduce labor, maintenance fees, storage and electrical consumption · Raise Productivity - Automation and integration, communication, findability · Foster Innovation - Enable collaboration, expertise location · Improve Online Engagement – enable user-driven, dynamic marketing initiatives With the coming technology wave we see four content imperatives. Every organization has had to reduce costs, cost cutting has become a way of life. Everyone is working three jobs as positions are eliminated. And so we have to reduce labor, reduce maintenance, and reduce money we are wasting on things like storing content that is redundant or no longer useful. We also, to fill that gap, need to raise productivity. Knowledge workers represent the fastest growing segment of the workforce, accounting for 40%-75% of the employees at organizations in sectors like financial services, life sciences, healthcare and retail.  What’s more, their wages total 18 percent of the United States GDP. And so we can’t afford information systems that don’t let our top performers be the best they can be. We look to automate the content processes, provide ways to integrate that content into our processes, provide communication to make decisions, and to make content more findable so people can make the right decision and move the process forward. And really to get ourselves out of the current financial status, we can only cut costs so far. We have to innovate out of economic tough times – to find new products and new markets. And to enable the innovation process, we have to enable collaboration and expertise location. So much of innovation is about building on innovations that have come before. To solve problems, we have to be able to find what our organization has already created. We find that problems we need to solve have already been solved if we can find the right document, the right person. So we have to provide systems that enable us to stand on the shoulders of our organization’s accomplishments. Good content drives great marketing. Online engagement is growing as an absolute necessity for modern growing marketing organizations that require the business users be enabled for dynamic marketing content creation, updates and targeted content creation and management. Unfortunately – if you are currently stuck with Documentum, you are really lacking in your Web Experience Management capabilities. Documentum previously used FatWire for web publishing. Now FatWire is part of Oracle. Oracle provides powerful web engagement capabilities: Increase sales and loyalty by optimizing online engagement Create, manage and moderate contextually relevant, targeted and interactive online experiences Optimize customer engagement across, web, mobile and social channels Manage large scale multichannel global online presence with integration to enterprise applications Enable business users to control their content and make their own updates Publish content from native files – enable navigation of project documents, procedures, policy information Enable content display and updates from existing web applications – one click to drag and drop content management functionality So you get the ability to self-publish information and make it navigable, to move the process of publishing from IT to business users, and the ability to address a whole new area of user engagement with web experience management. So… if you are still stuck with Documentum and don’t know what to do – contact us – not only will Oracle help you step away from the ledge, but also with the MoveOff Documentum program, we are offering you a way – trade-in your Documentum licenses for a 100% credit on Oracle WebCenter. How’s that for a nice bonus? It’s time to stop maintaining Documentum, and to start innovating with Oracle WebCenter. Learn More Here! To learn more about what Oracle WebCenter can offer you today – join us for a webcast – your eyes will be opened to all that’s possible. Do More with WebCenter: Extend Beyond Content Management

  Read the article

• Oracle Database Upcoming Event dates to know

  - by mandy.ho

  February may be a short month, but it's not short of exciting Oracle events. From information packed "Real Performance Days" to participation in one of the biggest IT Security events - look out for Oracle Database and let us know if you are there with us! Feb 13-18, 2011 - Las Vegas, NV TDWI World Conference Series Join Oracle in highlighting Exadata x2-2 and x2-8, along with Oracle Business Intelligence, Enterprise Performance management and Data Warehousing solutions. Oracle will be presenting a workshop - Oracle Data Integration: Best-of-Breed Solutions for the Enterprise Wednesday, February 16, 2011 7p.m - 9p.m Glen Goodrich, Director of Product Management Christophe Dupupet, Director of Product Management, Data Integration http://events.tdwi.org/events/las-vegas-world-conference-2011/sessions/session-list.aspx Feb 14-17, 2011 - Barcelona, Spain Mobile World Congress MWC is an event where Oracle showcases the near complete breadth and depth of value that our Communications Industry strategy and Hardware and Software Solutions can deliver. Oracle supports Communications Service Providers today and delivers platforms and flexibility primed for the future. Oracle will have a two story Pavilion, along with an Oracle Java and Embedded Solutions Center - App Planet. The Exhibition times are Monday, 14th February 09.00 - 19.00 Tuesday, 15th February 09.00 - 19.00 Wednesday, 16th February 09.00 - 19.00 Thursday, 17th February 09.00 - 16.00 Have questions? Meet with Oracle Sales representatives at the Oracle Café. Open every day from 9am to 17:00pm. http://eventreg.oracle.com/webapps/events/ns/EventsDetail.jsp?p_eventId=109912&src=6973382&src=6973382&Act=4 Feb 14-18, 2011 - San Francisco, CA RSA Conference As the world's most complete, open, integrated business software and hardware systems provider, Oracle can uniquely safeguard your information throughout its entire lifecycle. Learn more by attending these sessions: Cloud Computing: A Brave New World for Security and Privacy (CLD-201) Wednesday, February 16 at 8:30 a.m. Databases Under Attack - Securing Heterogeneous Database Infrastructures (DAS-301) Thursday, February 17, 2011 at 8:30 a.m. Seven Steps to Protecting Databases (DAS-402) Friday, February 18 at 10:10 a.m. RSA Conference Attendees will also have the opportunity to meet with Oracle Security Solution experts, see live product demos and more by visiting booth # 1559. Hours: Monday, February 14, 6:00 p.m. - 8:00 p.m., Tuesday, February 15, 11:00 a.m. - 6:00 p.m. and 4:30 p.m. - 6:00p.m., Wednesday, February 16, 11:00 a.m. - 6:00 p.m., and Thursday, February 17, 11:00 a.m. - 3:00 p.m. http://eventreg.oracle.com/webapps/events/ns/EventsDetail.jsp?p_eventId=127657&src=6967733&src=6967733&Act=12 Feb 21-25, 2011 - Various Locations IOUG Presents - A Day of Real World Performance with Tom Kyte, Andrew Holdsworth and Graham Wood These Oracle experts will debate, discuss and delineate the best practices for designing hardware architectures, deploying Oracle databases, and developing applications that deliver the fastest possible performance for your business.Topics are covered in a conversational format - with all three chiming in where appropriate. Each presenter has their own screen projector to demonstrate their individual points to the participants. Customers will have the opportunity to get their specific performance/tuning questions answered and learn how to balance all the different environmental requirements for their applications to improve performance. Register today for the following dates and locations • February 21 in San Diego, CA • February 22 in Los Angeles, CA • February 23 in Seattle, WA • February 25 in Phoenix, AZ http://www.ioug.org/tabid/194/Default.aspx Feb 8-24 - Various Oracle Enterprise Cloud Summit This series of full-day events with cloud experts, sharing real-world best practices, reference architectures and more continues during the month of February. Attend the Oracle Enterprise Cloud Summit to learn how to: • Build a state-of-the-art cloud architecture • Leverage your existing IT investments • Optimize your IT management processes Whether you are considering a move to cloud computing or have already adopted a cloud model, this event offers you the insights you need to take full advantage of cloud computing. Check below to see if the event is coming to a city near you. http://www.oracle.com/us/corporate/events/cloud-events-214342.html

  Read the article

• Framework 4 Features: Login Id Support

  - by Anthony Shorten

  Given that Oracle Utilities Application Framework 4 is available as part of Mobile Work Force Management and other product progressively I am preparing a number of short but sweet blog entries highlighting some of the new functionality that has been implemented. This is the first entry and it is on a new security feature called Login Id. In past releases of the Oracle Utilities Application Framework, the userid used for authentication and authorization was limited to eight (8) characters in length. This mirrored what the market required in the past with LAN userids and even legacy userids being that length. The technology market has since progressed to longer userid lengths. It is very common to hear that email addresses are being used as credentials for production systems. To achieve this in past versions of the Oracle Utilities Application Framework, sites had to introduce a short userid (8 characters in length) as an alias in your preferred security store. You then configured your J2EE Web Application Server to use the alias as credentials. This sometimes was a standard feaure of the security store and/or the J2EE Web Application Server, if you were lucky. If not, some java code has to be written to implement the solution. In Oracle Utilities Application Framework 4 we introduced a new attribute on the user object called Login Id. The Login Id can be up to 256 characters in length and is an alternative to the existing userid stored on the user object. This means the Oracle Utilities Application Framework can support both long and short userids. For backward compatibility we use the Login Id for authentication but the short userid for authorization and auditing. The user object within the Oracle Utilities Application Framework holds the translation. Backward compatibility is always a consideration in any of our designs for future or changed functionality. You will see reference to this fact in the blog entries I will be composing over the next few months. We have also thought about the flexibility in implementing this feature. The Login Id can be the same value of the Userid (the default for backward compatibility) or can be different. Both the Login Id and Userid have to be unique. This avoids sharing of credentials and is also backward compatible. You can manually enter the Login Id or provision it from Oracle Identity Manager (or other tool). If you use the Login Id only, then we will not autogenerate a short userid automatically as the rules for this can vary from site to site. You have a number of options there. Most Identity provisioning tools can generate a short userid at user creation time and this can be used. If you do not use provisioning tools, then you can write a class extension using the SDK to autoegenerate the userid based upon your sites preference. When we designed the feature there were lots of styles of generating userids (random, initial and surname, numbers etc). We could not really see a clear winner in that respect so we just allowed the extension to be inserted in if necessary. Most customers indicated to us that identity provisioning was the preferred way. This is why we released an Oracle Identity Manager integration with the framework. The Login id is case sensitive now which was not supported under userid. The introduction of the Login Id allows the product to offer flexible options when configuring security whilst maintaining backward compatibility.

  Read the article

• How do I set up nvidia graphics adapter to put out 1080p, it seems to be using interlace mode>

  - by keepitsimpleengineer

  After upgrading to 12.04, my mythbuntu client/server seems to be running in 1080i, the clue comes from: [ 1176.117] (II) NVIDIA(0): Setting mode "1920x1080_60i" [ 1231.340] (II) NVIDIA(0): Setting mode "DFP-1:1920x1080_60@1920x1080+0+0" This is from Xorg.0.log. This whole thing started from video tearing when watching Mythtv recordings. It didn't happen in 10.10. Should I use "TVStandard" "HD1080p" in the screen section since this is a dedicated HTPC? It only connects to an HDTV (1080p) via hdmi. Here is the current xorg.conf file: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 270.29 (buildd@allspice) Fri Feb 25 14:42:07 UTC 2011 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup # InputDevice "Keyboard0" "CoreKeyboard" # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup # InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" FontPath "unix/:7100" EndSection # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup #Section "InputDevice" # # generated from default # Identifier "Mouse0" # Driver "mouse" # Option "Protocol" "auto" # Option "Device" "/dev/psaux" # Option "Emulate3Buttons" "no" # Option "ZAxisMapping" "4 5" #EndSection # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup #Section "InputDevice" # # generated from default # Identifier "Keyboard0" # Driver "kbd" #EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "SAMSUNG" HorizSync 26.0 - 81.0 VertRefresh 24.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 240" Option "TripleBuffer" "1" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "DFP: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection After a little digging, the question changes slightly, to wit... Per Chapter 19 of nvidia README... "If the EDID for the display device reported a preferred mode timing, and that mode timing is considered a valid mode, then that mode is used as the "nvidia-auto-select" mode." The EDID for my HDMI connected LCD monitor says use first device as preferred. Prefer first detailed timing : Yes Also: (--) NVIDIA(0): EDID maximum pixel clock : 230.0 MHz The list: (from startx -- -verbose 6 ) (--) NVIDIA(0): Detailed Timings: (--) NVIDIA(0): 1920 x 1080 @ 60 Hz (--) NVIDIA(0): Pixel Clock : 148.50 MHz (--) NVIDIA(0): HRes, HSyncStart : 1920, 2008 (--) NVIDIA(0): HSyncEnd, HTotal : 2052, 2200 (--) NVIDIA(0): VRes, VSyncStart : 1080, 1084 (--) NVIDIA(0): VSyncEnd, VTotal : 1089, 1125 (--) NVIDIA(0): H/V Polarity : +/+ This is the actual mode selected: (from xorg.0.log) (--) NVIDIA(0): 1920 x 1080 @ 60 Hz (--) NVIDIA(0): Pixel Clock : 74.18 MHz (--) NVIDIA(0): HRes, HSyncStart : 1920, 2008 (--) NVIDIA(0): HSyncEnd, HTotal : 2052, 2200 (--) NVIDIA(0): VRes, VSyncStart : 1080, 1084 (--) NVIDIA(0): VSyncEnd, VTotal : 1094, 1124 (--) NVIDIA(0): H/V Polarity : +/+ (--) NVIDIA(0): Extra : Interlaced (--) NVIDIA(0): CEA Format : 5 So my HTPC is down-converting to 1080i and then the Monitor is up-converting to 1080p How can I fix this, please?

  Read the article

• AWS .NET SDK v2: setting up queues and topics

  - by Elton Stoneman

  Originally posted on: http://geekswithblogs.net/EltonStoneman/archive/2013/10/13/aws-.net-sdk-v2-setting-up-queues-and-topics.aspxFollowing on from my last post, reading from SQS queues with the new SDK is easy stuff, but linking a Simple Notification Service topic to an SQS queue is a bit more involved. The AWS model for topics and subscriptions is a bit more advanced than in Azure Service Bus. SNS lets you have subscribers on multiple different channels, so you can send a message which gets relayed to email address, mobile apps and SQS queues all in one go. As the topic owner, when you request a subscription on any channel, the owner needs to confirm they’re happy for you to send them messages. With email subscriptions, the user gets a confirmation request from Amazon which they need to reply to before they start getting messages. With SQS, you need to grant the topic permission to write to the queue. If you own both the topic and the queue, you can do it all in code with the .NET SDK. Let’s say you want to create a new topic, a new queue as a topic subscriber, and link the two together. Creating the topic is easy with the SNS client (which has an expanded name, AmazonSimpleNotificationServiceClient, compare to the SQS class which is just called QueueClient): var request = new CreateTopicRequest(); request.Name = TopicName; var response = _snsClient.CreateTopic(request); TopicArn = response.TopicArn; In the response from AWS (which I’m assuming is successful), you get an ARN – Amazon Resource Name – which is the unique identifier for the topic. We create the queue using the same code from my last post, AWS .NET SDK v2: the message-pump pattern, and then we need to subscribe the queue to the topic. The topic creates the subscription request: var response = _snsClient.Subscribe(new SubscribeRequest { TopicArn = TopicArn, Protocol = "sqs", Endpoint = _queueClient.QueueArn }); That response will give you an ARN for the subscription, which you’ll need if you want to set attributes like RawMessageDelivery. Then the SQS client needs to confirm the subscription by allowing the topic to send messages to it. The SDK doesn’t give you a nice mechanism for doing that, so I’ve extended my AWS wrapper with a method that encapsulates it: internal void AllowSnsToSendMessages(TopicClient topicClient) { var policy = Policies.AllowSendFormat.Replace("%QueueArn%", QueueArn).Replace("%TopicArn%", topicClient.TopicArn); var request = new SetQueueAttributesRequest(); request.Attributes.Add("Policy", policy); request.QueueUrl = QueueUrl; var response = _sqsClient.SetQueueAttributes(request); } That builds up a policy statement, which gets added to the queue as an attribute, and specifies that the topic is allowed to send messages to the queue. The statement itself is a JSON block which contains the ARN of the queue, the ARN of the topic, and an Allow effect for the sqs:SendMessage action: public const string AllowSendFormat= @"{ ""Statement"": [ { ""Sid"": ""MySQSPolicy001"", ""Effect"": ""Allow"", ""Principal"": { ""AWS"": ""*"" }, ""Action"": ""sqs:SendMessage"", ""Resource"": ""%QueueArn%"", ""Condition"": { ""ArnEquals"": { ""aws:SourceArn"": ""%TopicArn%"" } } } ] }"; There’s a new gist with an updated QueueClient and a new TopicClient here: Wrappers for the SQS and SNS clients in the AWS SDK for .NET v2. Both clients have an Ensure() method which creates the resource, so if you want to create a topic and a subscription you can use:  var topicClient = new TopicClient(“BigNews”, “ImListening”); And the topic client has a Subscribe() method, which calls into the message pump on the queue client: topicClient.Subscribe(x=>Log.Debug(x.Body)); var message = {}; //etc. topicClient.Publish(message); So you can isolate all the fiddly bits and use SQS and SNS with a similar interface to the Azure SDK.

  Read the article

• Getting away from a customized Magento 1.4 installation - Magento 1.6, OpenCart, or others?

  - by Phil

  I'm dealing with a Magento 1.4.0.0 Community Edition installation with various undocumented changes to the core (mostly integration with an ERP system), an outdated Sweet Tooth Points & Rewards module and some custom payment providers. It also doubles as a mediocre blogging/CMS system. It has one store each for 3 different languages, with about 40 product categories for a few hundred products. [rant] With no prior experience with any PHP e-commerce systems, I find it very difficult to work with. I attempted to install Magento 1.4.0.0 on my local WAMP dev machine, it installs fine, but the main page or search do not show any products no matter what I do in the backend admin panel. I don't know what's wrong with it, and whatever information I googled is either too old or too new from Magento 1.4. Later I'm given FTP access to the testing server, which neither my manager or I have permission to install XDebug on, as apparantly it runs on the same server as the production server (yikes). Trying to learn how Magento works is torture. I spent a week trying to add some fields into the Onepage Checkout before giving up and went to work on something else. The template system, just like the rest of Magento, is a bloated mishmash of overcomplicated directory structures, weird config xml files and EAV databases. I went into 6 different models and several content blocks in the backend just to change what the front page looks like. With little-to-none helpful and clear documentation (unlike CodeIgniter) and various breaking changes between minor point revisions which makes it hard to find useful information, Magento 1.4 is a developer killer. [/rant] The client is planning to redesign the site and has decided it might as well as move on from this unsustainable, hacky, upgrade-unfriendly, developer-unfriendly mess. Magento 1.4 is starting to show its age, with Magento 1.7 coming soon, the client is considering upgrading to Magento 1.6 or 1.7 if it has improved from 1.4. The customizations done to the current Magento 1.4 installation will have to be redone, and a new license for the Sweet Tooth Points & Rewards module will have to be bought. The client is also open to other e-commerce systems. I've looked at OpenCart and it seems to be quite developer friendly with a fairly simple structure. I found some complaints regarding its performance when the shop has thousands of categories or products, but this is not an issue with the current number of products my client has. It seems to be solid ground for easy customization to bring the rewards system and ERP integration over. What should the client upgrade to in this case?

  Read the article

• Upgrading Code from 2007 to 2010

  - by MOSSLover

  So I’ve been doing some upgrades just to see if things will work from 2007 to 2010.  So far most of the stuff I want works, but obviously there are some things that break.  Did you guys know that in 2007 you could add a webpart to the view pages for lists and libraries without losing the toolbar?  In 2010 the ribbon disappears every time you add a webpart.  So if you are using Scot Hillier’s Codeplex project to hide buttons it will not work the same way, because the ribbon is going to disappear altogether. I have also learned another reason why standalone installations are the bane of my existence.  Nine times out of ten the installation is done using Network Service as the application pool account.  You are wondering why is this bad?  Well, let’s just say the site collection administrator with local admin rights wants to attach the IIS Worker process and debug say a webpart.  Visual Studio 2010 will throw a nasty error that tells you that you are not an administrator.  You will say, but I am an administrator?  I have all the correct group permissions on the server and on SQL and in SharePoint.  Then you will go in and decide let’s add my own admin account just to see if I can attach the debugger and you will notice that works properly.  So the morale of the story is create a separate account on your development environment to run all the SharePoint Services and such.  You don’t need to go all out and create the best practices amount of accounts if it’s just your dev environment.  I would at least create one single account to run all your SharePoint process (Services, SQL, and App Pool).  Also, don’t run a standalone install unless you want to kill kittens (this is a quote from Todd Klindt).  We love kittens they are cute and awesome.  Besides you learn more if you click Complete and just skip standalone.  You will learn how to setup SQL Server 2008 and you will learn how to configure your environment.  It will help you in the long run.  So I have ranted enough for today I figure these are enough tidbits for you this time around.  The two of you who read my blog and I know some of you are friends who don’t understand SharePoint.  I might as well have just done “wahwahwahwah” in Charlie Brown adult speak.  Thanks for reading as usual.  I’ll catch you all when I complain more about the upgrade process and share more tidbits, which will inevitably become a presentation at a conference or two. Technorati Tags: Upgrade Code SharePoint 2007 to 2010,Visuaul Studio 2010,SharePoint 2010

  Read the article

• How to get my IR remote to work? Lirc can't see it

  - by user1234567

  I'm using Ubuntu 11.10 (amd64) and I'm trying to get my infrared remote control working. The IR device is a part of a DVB-T USB stick (Based on a RTL2832u chip). I'm using these drivers - it's the only way of getting this device to work under 11.10 that I found. It's a big impromevent from previous Ubuntu version, where I had to edit the driver's code. The device works quite great - and the IR part of it works, too. The driver's page says that the code it's in alpha stage, but I'm pretty sure that my issue has nothing to do with that. If, and only if driver's module is loaded with parameter rtl2832u_rc_mode=2 (which means "use NEC protocol for IR") the remote kind of works, I can see this by running cat /dev/.. ../input6 - when I press a button, random letters appear. The remote works just like a keyboard, but keys are totally messed up - when I press '5' the volume goes down, etc. I would like to use Lirc to fix that, but Lirc can't detect my device (i.e. irw shows nothing). I suspect, it's because something gets into control of the device and sets it up as a keyboard. Lirc seems to be working, it's KDE settings module works too, but it just doesn't detect the device. The Lirc page describes this issue, but since 2009 - the last year when that page was updated, Ubuntu moved from HAL (described there) to DeviceKit, rendering provided instruction useless. I had a similar issue with my previous remote, but the keys were not messed up so much - the remote was usable, so I gave up trying to get Lirc working. I tried the answer provided here, but it changed nothing. I also tried forcing lircd to use my device, but this didn't work too: for i in /sys/class/input/input* ; do echo -n "$(basename "$i"): "; cat "$i/name"; done shows input0: Power Button input1: Power Button input2: Logitech Logitech USB Keyboard input3: A4Tech PS/2+USB Mouse input6: IR-receiver inside an USB DVB receiver But when I run: lircd -n --device=name='IR*' as root (also tried with the full name) I always see: lircd-0.9.0[3983]: lircd(default) ready, using /var/run/lirc/lircd lircd-0.9.0[3983]: accepted new client on /var/run/lirc/lircd lircd-0.9.0[3983]: could not get file information for name=IR* lircd-0.9.0[3983]: default_init(): No such file or directory lircd-0.9.0[3983]: Failed to initialize hardware So, how to set up Lirc with devinput driver in such case?

  Read the article

• Unit Testing TSQL

  - by Grant Fritchey

  I went through a period of time where I spent a lot of effort figuring out how to set up unit tests for TSQL. It wasn't easy. There are a few tools out there that help, but mostly it involves lots of programming. well, not as much as before. Thanks to the latest Down Tools Week at Red Gate a new utility has been built and released into the wild, SQL Test. Like a lot of the new tools coming out of Red Gate these days, this one is directly integrated into SSMS, which means you're working where you're comfortable and where you already have lots of tools at your disposal. After the install, when you launch SSMS and get connected, you're prompted to install the tSQLt example database. Go for it. It's a quick way to see how the tool works. I'd suggest using it. It' gives you a quick leg up. The concepts are pretty straight forward. There are a series of CLR commands that you use to configure a test and the test assertions. In between you're calling TSQL, either calls to your structure, queries, or stored procedures. They already have the one things that I always found wanting in database tests, a way to compare tables of results. I also like the ability to create a dummy copy of tables for the tests. It lets you control structures and behaviors so that the tests are more focused. One of the issues I always ran into with the other testing tools is that setting up the tests might require potentially destructive changes to the structure of the database (dropping FKs, etc.) which added lots of time and effort to setting up the tests, making testing more difficult, and therefor, less useful. Functionally, this is pretty similar to the Visual Studio tests and TSQLUnit tests that I used to use. The primary improvement over the Visual Studio tests is that I'm working in SSMS instead of Visual Studio. The primary improvement over TSQLUnit is the SQL Test interface it self. A lot of the functionality is the same, but having a sweet little tool to manage & run the tests from makes a huge difference. Oh, and don't worry. You can still run these tests directly from TSQL too, so automation has not gone away. I'm still thinking about how I'd use this in a dev environment where I also had source control to fret. That might be another blog post right there. I'm just getting started with SQL Test, so this is the first of several blog posts & videos. Watch this space. Try the tool.

  Read the article

• need some concrete examples on user stories, tasks and how they relate to functional and technical specifications

  - by gideon

  Little heads up, Im the only lonely dev building/planning/mocking my project as I go. Ive come up with a preview release that does only the core aspects of the system, with good business value and I've coded most of the UI as dirty throw-able mockups over nicely abstracted and very minimal base code. In the end I know quite well what my clients want on the whole. I can't take agile-ish cowboying anymore because Im completely dis-organized and have no paper plan and since my clients are happy, things are getting more complex with more features and ideas. So I started using and learning Agile & Scrum Here are my problems: I know what a functional spec is.(sample): Do all user stories and/or scenarios become part of the functional spec? I know what user stories and tasks are. Are these kinda user stories? I dont see any Business Value reason added to them. I made a mind map using freemind, I had problems like this: Actor : Finance Manager Can Add a Financial Plan into the system because well thats the point of it? What Business Value reason do I add for things like this? Example : A user needs to be able to add a blog article (in the blogger app) because..?? Its the point of a blogger app, it centers around that feature? How do I go into the finer details and system definitions: Actor: Finance Manager Action: Adds a finance plan. This adding is a complicated process with lots of steps. What User Story will describe what a finance plan in the system is ?? I can add it into the functional spec under definitions explaining what a finance plan is and how one needs to add it into the system, but how do I get to the backlog planning from there? Example: A Blog Article is mostly a textual document that can be written in rich text in the system. To add a blog article one must...... But how do you create backlog list/features out of this? Where are the user stories for what a blog article is and how one adds/removes it? Finally, I'm a little confused about the relations between functional specs and user stories. Will my spec contain user stories in them with UI mockups? Now will these user stories then branch out tasks which will make up something like a technical specification? Example : EditorUser Can add a blog article. Use XML to store blog article. Add a form to add blog. Add Windows Live Writer Support. That would be agile tasks but would that also be part of/or form the technical specs? Some concrete examples/answers of my questions would be nice!!

  Read the article

• Did I lost my RAID again?

  - by BarsMonster

  Hi! A little history: 2 years ago I was really excited to find out that mdadm is so powerful so it even can reshape arrays so you can start with a smaller array and the grow it as you need. I've bought 3x1Tb drives and made RAID-5. It was fine for a year. Then I bought 2x more, and tried to reshape to RAID-6 out of 5 drives, and due to some mess with superblock versions, lost all content. Had to rebuild it from scratch, but 2Tb of data were gone. Yesterday I bought 2 more drives, and this time I had everything: properly built array, UPS. I've disabled write intent map, added 2 new drives as a spare and run a command to grow array to 7-disk. It started working, but speed was ridiculously slow, ~100kb/sec. AFter processing first 37Mb at such an amasing speed, one of old HDDs fails. I properly shutdown PC and disconnected failed drive. After bootup it appeared it recreated intent map as it was still in mdadm config, so I removed it from config and rebooted again. Now all I see is that all mdadm processes deadlocks, and don't do anything. PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1937 root 20 0 12992 608 444 D 0 0.1 0:00.00 mdadm 2283 root 20 0 12992 852 704 D 0 0.1 0:00.01 mdadm 2287 root 20 0 0 0 0 D 0 0.0 0:00.01 md0_reshape 2288 root 18 -2 12992 820 676 D 0 0.1 0:00.01 mdadm And all I see in mdstat is: $ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sdb1[1] sdg1[4] sdf1[7] sde1[6] sdd1[0] sdc1[5] 2929683456 blocks super 1.2 level 6, 1024k chunk, algorithm 2 [7/6] [UU_UUUU] [>....................] reshape = 0.0% (37888/976561152) finish=567604147.2min speed=0K/sec I've already tried mdadm 2.6.7, 3.1.4 and 3.2 - nothing helps. Did I lost my data again? Any suggestions how can I make it work? OS is Ubuntu Server 10.04.2... PS. Needless to say that data is unaccessible - I cannot mount /dev/md0 as save the most valuable data. You can see my disappointment - the very specific thing I was excited about failed twice taking 5Tb of my data with it.

  Read the article

• Introducing the First Global Web Experience Management Content Management System

  - by kellsey.ruppel

  By Calvin Scharffs, VP of Marketing and Product Development, Lingotek Globalizing online content is more important than ever. The total spending power of online consumers around the world is nearly $50 trillion, a recent Common Sense Advisory report found. Three years ago, enterprises would have to translate content into 37 language to reach 98 percent of Internet users. This year, it takes 48 languages to reach the same amount of users.  For companies seeking to increase global market share, “translate frequently and fast” is the name of the game. Today’s content is dynamic and ever-changing, covering the gamut from social media sites to company forums to press releases. With high-quality translation and localization, enterprises can tailor content to consumers around the world.  Speed and Efficiency in Translation When it comes to the “frequently and fast” part of the equation, enterprises run into problems. Professional service providers provide translated content in files, which company workers then have to manually insert into their CMS. When companies update or edit source documents, they have to hunt down all the translated content and change each document individually.  Lingotek and Oracle have solved the problem by making the Lingotek Collaborative Translation Platform fully integrated and interoperable with Oracle WebCenter Sites Web Experience Management. Lingotek combines best-in-class machine translation solutions, real-time community/crowd translation and professional translation to enable companies to publish globalized content in an efficient and cost-effective manner. WebCenter Sites Web Experience Management simplifies the creation and management of different types of content across multiple channels, including social media.  Globalization Without Interrupting the Workflow The combination of the Lingotek platform with WebCenter Sites ensures that process of authoring, publishing, targeting, optimizing and personalizing global Web content is automated, saving companies the time and effort of manually entering content. Users can seamlessly integrate translation into their WebCenter Sites workflows, optimizing their translation and localization across web, social and mobile channels in multiple languages. The original structure and formatting of all translated content is maintained, saving workers the time and effort involved with inserting the text translation and reformatting.  In addition, Lingotek’s continuous publication model addresses the dynamic nature of content, automatically updating the status of translated documents within the WebCenter Sites Workflow whenever users edit or update source documents. This enables users to sync translations in real time. The translation, localization, updating and publishing of Web Experience Management content happens in a single, uninterrupted workflow.  The net result of Lingotek Inside for Oracle WebCenter Sites Web Experience Management is a system that more than meets the need for frequent and fast global translation. Workflows are accelerated. The globalization of content becomes faster and more streamlined. Enterprises save time, cost and effort in translation project management, and can address the needs of each of their global markets in a timely and cost-effective manner.  About Lingotek Lingotek is an Oracle Gold Partner and is going to be one of the first Oracle Validated Integrator (OVI) partners with WebCenter Sites. Lingotek is also an OVI partner with Oracle WebCenter Content.  Watch a video about how Lingotek Inside for Oracle WebCenter Sites works! Oracle WebCenter will be hosting a webinar, “Hitachi Data Systems Improves Global Web Experiences with Oracle WebCenter," tomorrow, September 13th. To attend the webinar, please register now! For more information about Lingotek for Oracle WebCenter, please visit http://www.lingotek.com/oracle.

  Read the article

• JFall 2012

  - by Geertjan

  JFall 2012 was over far too soon! Seven tracks going on simultaneously in a great location, with many artifacts reminding me of JavaOne, and nice snacks and drinks afterwards. The day started, as such things always do, with a keynote. Thanks to @royvanrijn for the photo below, I didn't take any myself and without a picture this report might have been too dry: What you see above is Steve Chin riding into the keynote hall on his NightHacking bike. The keynote was interesting, I can't be too complimentary about it, since I was part of it myself. Bert Ertman introduced the day and then Steve Chin took over, together with Sharat Chander, Tom Eugelink, Timon Veenstra, and myself. We had a strict choreography for the keynote, one that would ensure a lot of variation and some unexpected surprises, such as Steve being thrown off the stage a few times by Bert because of mentioning JavaOne too many times, rather than the clearly much cooler JFall. Steve talked about JavaOne and the direction Java is headed in, Sharat talked about JavaME and embedded devices, Steve and Tom did a demo involving JavaFX, I did a Project Easel demo, and Timon from Ordina talked about his Duke's Choice Award winning AgroSense project. I think the Project Easel demo (which I repeated later in a screencast for Parleys arranged by Eugene Boogaart) came across well and several people I spoke to especially like the roundtrip/bi-directional work that can be done, from browser to IDE and back again, very simply and intuitively. (In a long conversation on the drive back home afterwards, the scenario of a designer laying out the UI in HTML and then handing the HTML to a developer for back-end work, a developer who would then find it convenient to open the HTML in a browser and quickly navigate from the browser to the resources within the IDE, was discussed and considered to be extremely interesting and worth considering adopting NetBeans for, for no other reason than that.) Later I attended a session by David Delabassee on Java EE 7, Hans Dockter on Gradle, and Sander Mak on cross-build injection attacks. I was sorry to have missed Martijn Verburg's session, which sounded like it was really fantastic, among others, such as Gerrit Grunwald. I did a session too, entitled "Unlocking the Java EE 6 Platform", which was very well attended, pretty much a full room, and the demo went very smoothly. I talked to many people, e.g., a long time with Hans Dockter about how cool Gradle is and how great the Gradle/NetBeans plugin is turning out to be. I also had a long conversation (and did a demo) with Chris Chedgey, from Structure101, after his session, which was incredibly well attended; very interesting how popular modularity is. I met several people for the first time, as well as some colleagues from past places I've worked at. All in all, it was a great conference, unfortunately too short, which was very well attended (clearly over 1000) people, with several international speakers, as well as international attendees such as Mattias Karlsson, Sweden JUG leader. And, unsurprisingly, I came across NetBeans Platform applications again, none of which I had ever heard of before. In each case, "our fat client application" was mentioned in passing, never as a main application, and never in a context where there are plans for the application to be migrated to the web or mobile, simply because doing so makes no business sense at all. Great times at JFall, looking forward to meeting with some of the people I met again soon.

  Read the article

• Difference between the terms Material & Effect

  - by codey

  I'm making an effect system right now (I think, because it may be a material system... or both!). The effects system follows the common (e.g. COLLADA, DirectX) effect framework abstraction of Effects have Techniques, Techniques have Passes, Passes have States & Shader Programs. An effect, according to COLLADA, defines the equations necessary for the visual appearance of geometry and screen-space image processing. Keeping with the abstraction, effects contain techniques. Each effect can contain one or many techniques (i.e. ways to generate the effect), each of which describes a different method for rendering that effect. The technique could be relate to quality (e.g. high precision, high LOD, etc.), or in-game-situation (e.g. night/day, power-up-mode, etc.). Techniques hold a description of the textures, samplers, shaders, parameters, & passes necessary for rendering this effect using one method. Some algorithms require several passes to render the effect. Pipeline descriptions are broken into an ordered collection of Pass objects. A pass provides a static declaration of all the render states, shaders, & settings for "one rendering pipeline" (i.e. one pass). Meshes usually contain a series of materials that define the model. According to the COLLADA spec (again), a material instantiates an effect, fills its parameters with values, & selects a technique. But I see material defined differently in other places, such as just the Lambert, Blinn, Phong "material types/shaded surfaces", or as Metal, Plastic, Wood, etc. In game dev forums, people often talk about implementing a "material/effect system". Is the material not an instance of an effect? Ergo, if I had effect objects, stored in a collection, & each effect instance object with there own parameter setting, then there is no need for the concept of a material... Or am I interpreting it wrong? Please help by contributing your interpretations as I want to be clear on a distinction (if any), & don't want to miss out on the concept of a material if it should be implemented to follow the abstraction of the DirectX FX framework & COLLADA definitions closely.

  Read the article

• "Why We Chose Fusion CRM" by Vikas Bhambri, Managing Partner, The Athene Group

  - by Natalia Rachelson

  Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} A guest post by Vikas Bhambri, Managing Partner, The Athene Group This year The Athene Group (www.theathenegroup.com) celebrated our tenth anniversary. The company has accomplished a lot in ten years overcoming a number of hurdles and challenges to have grown organically to a 150+ person global company with offices in the US, UK, and India and customers in the US, Canada, and Europe. Now more than ever with the current global landscape from an economic and competitive standpoint it was vital that we make some changes to remain successful for the next ten years. There were two key initiatives that we discussed internally that would enable us to successfully accomplish this – collaboration and the concept of “insight to action”. With our existing Oracle CRM On Demand platform we had components of this but not the full depth and breadth that we were looking for. When we started to discuss Fusion CRM we immediately saw several next generation tools that would embrace these two objectives. For a consulting and development organization the collaboration required between business development and consulting delivery is as important as the collaboration required during the projects between the project delivery and account management teams. The Activity Streams functionality in Fusion CRM immediately addressed the communication of key discussion topics and exchanges around our clients. Of course when we saw the Oracle Social Network (which is part of our Fusion CRM roadmap) we were blown away. The combination OSN and our CRM is going to make us more effective as we discuss and work cohesively on client engagements – ensuring mutual success for both Athene and our clients. When we looked at “insight to action” we saw that we had a great platform when folks were at their desks, unfortunately a lot of our business development and consulting folks are on the road. The Fusion Mobile Sales and Fusion Outlook Desktop provide information to our teams when they are on the go. So that they can provide real-time information and react to real-time information provided by their peers. We are in the early stages of our transformative experience with Fusion CRM but we believe the platform along with our people and processes are going to help us achieve our goals in the future.

  Read the article

• Sign up Today for User Feedback Sessions at Oracle OpenWorld and JavaOne 2012

  - by Lionel Dubreuil

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 You’re Invited to Sign Up for Oracle Usability Feedback Sessions SIGN UP TODAY to get the most from your conference experience by participating in a usability feedback session where your expertise will help Oracle develop outstanding products and solutions. The Oracle User Experience team is conducting a Usability Evaluation on publishing and accessing Oracle Enterprise Repository content when building SOA projects in JDeveloper. We are asking Developers and Architects who build or integrate applications using SOA Suite to take a look at the interaction between JDeveloper with the Enterprise Repository.  We are looking for feedback on the interaction between JDeveloper and Oracle Enterprise Repository so that we may improve the User Interface in a future release. The feedback sessions will be conducted during the Oracle OpenWorld and JavaOne Conferences, at the Intercontinental Hotel in San Francisco, CA. Sessions will last 1 hour and will be held on Monday, October 1 through Wednesday, October 3, 2012. This event fills up quickly, and space is limited. If you are interested in participating, please send an email to [email protected] with the following information: Identification Name: _________________________________ Company Name:  _________________________ Job Title: Email: Phone Number (work, mobile, include country code): Which conference are you attending? _____Oracle OpenWorld _____JavaOne Have you ever participated in usability activities with Oracle or any of its subsidiaries? ____Yes; specify __________________________________________________ ____No Are you currently using JDeveloper? ____Yes ; specify version(s): _______________________________ ____No How long have you used JDeveloper? ____ Less than 1 year ____ 1 - 2 years ____ 3 - 4 years ____ 4 + years Are you currently using SOA features in JDeveloper? ____Yes ____No How long have you used SOA features in JDeveloper? ____ Less than 1 year ____ 1 - 2 years ____ 3 - 4 years ____ 4 + years How often do you use SOA features in JDeveloper? ____ Daily ____ 2 - 3 times a week ____ Once a week  ____ Once a month or less Briefly describe the types of SOA tasks you use JDeveloper to perform: _____________________________________ _____________________________________ Please list your availability If you know your availability; please let me know which day you would prefer to participate, Monday, Tuesday or Wednesday. Limited sessions are available on each day, and each session lasts 1 hour. Thank you for taking the time to complete this questionnaire.  It will help us match you to the best suited feedback session. Once we receive your email, we will contact you to set up a time and day for participation. You'll find more information about our on-site lab on the VoX (Voice of User Experience) blog, and on our Events page at Usable Apps. /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif";}

  Read the article

• #iPad at One Week: A Great Device Made with a Heavy Hand

  - by andrewbrust

  I have now had my iPad for a little over a week. In that time, Apple introduced the world to its iPhone OS 4 (and the SDK agreement’s draconian new section 3.3.1), HP introduced is Slate, and Microsoft got ready to launch Visual Studio 2010 and .NET 4.0. And through it all I have used my iPad. I've used it for email, calendar, controlling my Sonos, and writing an essay. I've used it for getting on TripIt and Twitter, and surfing the Web. I've used it for online banking, and online ordering and delivery of food. And the verdict? Honestly? I think it's a great device and I thoroughly enjoy using it. The screen is bright and vibrant. I am surprisingly fast and accurate when I type on it. The touch screen's responsiveness is nearly flawless. The software, including a number of third party applications, include pleasing animations and use of color that make it fun to get work done. And speaking of work, the Exchange integration is, dare I say it, robust. Not as full-featured as on a PC or Windows Mobile device, but still offering core functionality and, so far at least, without bugs. The UI is intuitive, not just to me, but also to my 5 1/2 year old, and also to my nearly-3-year-old son. They picked it up and, with just just a few pointers from me, they almost immediately knew what to do, whether they were looking at photos (and swiping/flicking along as they did so), using a drawing program, playing a game, or watching YouTube videos. The younger of the two of them even tried to get up on a chair and grab the thing today. He dropped it, from about 4 feet off the ground. And it's still fine. (Meanwhile, I'll be keeping it on a higher shelf.) I cannot fully describe yet what makes this form factor and this product so appealing. Maybe it's that it's an always-on device. Maybe it's just being able to hold such a nice, relatively large display so close. Maybe it's the design sensibility, that seems to pervade throughout the app ecosystem. Or maybe it's that one's fingers, and not pens or mice, are the software's preferred input device. Whatever the attraction, it's strong. And no matter how much I tend to root for Microsoft and against Apple, Cupertino has, in my mind, scored big, Can Microsoft compete? Yes, but not with the Windows 7 standard UI (nor with individual OEMs’ own UIs on top). I hope Microsoft builds a variant of the Windows Phone 7 specifically for tablet devices. And I hope they make it clear that all developers, and programming languages, are welcome to the platform. Once that’s established, the OEMs have to build great hardware with fast, responsive touch screens, under Microsoft's watchful eye. That may be the hardest part of getting this right. No matter what, Microsoft's got a fight on its hands. I don't know if it can count on winning that fight, either. But Silverlight and Live Tiles could certainly help. And so can treating developers like adults.  Apple seems intent on treating their devs like kids, and then giving the kids a curfew.  For that, dev-friendly Microsoft may one day give thanks.

  Read the article

• TomEE Integration in NetBeans Next

  - by Geertjan

  At JavaOne 2013, there was a lot of buzz around the TomEE server, e.g., many Tweets, nice party, and a new TomEE consulting company. For those tracking TomEE developments, it is interesting to note that recently the NetBeans IDE development builds have had added to them... TomEE support. Note: The TomEE support described here is not in NetBeans IDE 7.4, but in development builds for the next release of NetBeans IDE.For example, with NetBeans IDE development builds you're able to: register TomEE as a server in the Services window (TomEE has several distributions, e.g., one can use the "with JAX-RS" one, for example) create a Java EE 6 web project (e.g., Maven based) against this server create JPA entities from database create JAX-RS classes from JPA entities create JSF pages from JPA entities the IDE lets you create a new data source for TomEE and deploy it to the server the IDE figures out the components that are already packaged in TomEE, and the fact that (unlike with regular Tomcat), it does not need to package any components such as JSF implementation, persistence provider, or JAX-RS runtime, so that the resulting WAR file is very small the IDE can also do "deploy on save" with TomEE, so that your development cycle is very fast Adam Bien blogged about how he set up TomEE sometime ago, here. The official support in NetBeans IDE will be much more tightly integrated, simplifying the steps Adam describes. For example, the IDE does step 2 from Adam's blog for you, i.e., it sets up TomEE deployment roles. Moreover, it knows about all the technologies included in TomEE so that it can optimize the packaging; it knows about TomEE's persistence setup; it can work with TomEE data sources, etc. Below you see a Maven-based Java EE 6 PrimeFaces application (all entities and JSF pages generated from a database) deployed to TomEE in NetBeans IDE: And here's the management console for configuring and finetuning TomEE in NetBeans IDE: When I tried out the NetBeans IDE development build and TomEE, to see how everything fits together, I was surprised at how fast TomEE started up. Not sure what they did to it, but seems like a server on steroids. And setting it up in NetBeans IDE was trivial. Add the simple set up of TomEE in NetBeans IDE to the many benefits that the widely praised out of the box NetBeans Maven tools make possible, together with the fact that not one single plugin had to be installed to get everything you see described here up and running... and you have a really powerful combination of dev tools, all for free.

  Read the article

• Why I Love Microsoft Development

  - by Brian Lanham

  I've been writing software for a while and recently had an opportunity to broaden my horizons and start developing for iOS. We decided to leverage, as much as possible, our existing skills and use MonoTouch and MonoDevelop by Novell.    For those of you who do not know, Mono is a .NET port originally designed for Linux but adapted for other platforms as well. MonoTouch is a port specifically for building iOS applications using the .NET framework. MonoDroid is a port (in CTP-esque release) for Android.   A MISSING COMPONENT - VISUAL DESIGNER   MonoDevelop lacks one very significant component compared with other tools I am using: NO VISUAL DESIGNER. Instead of using an integrated visual designer, MonoDevelop shells to the Mac OS "Interface Builder".  Since MonoDevelop lets me have a "Visual Studio-esque" feel *and* I get to use C#, AND it's FREE, I am gladly willing to overlook this.  In fact, it's not even a question.  Free?  Sure, I'll take it with no Visual Designer.   In my experiences I've grown from UNIX and DOS to .NET development through many steps. Java/JSP/Servlets; Windows; Web; etc. I've been doing .NET for quite a few years and I guess I just got "comfortable" with the tools.   WHY AM I NOT GETTING IT?   Interface Builder (IB) is amazingly confusing for me. I had the opportunity to speak at the Northern VA Code Camp on 12/11/2010. My presentation was "Getting Started with iOS Development using MonoTouch and C#".    At the visual design part of the presentation, I asked one of the 3 or 4 Mac developers in the room about my confusion with the IB. I don't understand why the "Classes" list includes objects. I don't understand what "File's Owner" is. And, most importantly, WHAT THE HECK IS AN OUTLET AND WHY IS IT NECESSARY?!?!?"   His response to these question (especially Outlets): "They did it wrong."   I'm accustom to a visual designer that creates variables for graphical widgets for me. Not IB. Instead, I have to create "Outlets" manually. I still do not understand why and, the explanation from a seasoned Mac developer is that it's wrong. (He received nods of confirmation from the other Mac devs in the room.)   I LOVE MS DEV   I love development for Microsoft platforms using Microsoft development tools. I love Windows 7. I love Visual Studio 2010. I love SQL Server. Azure, Entity Framework, Active Directory, Office, WCF/WF/WPF, etc. are all designed with integration in mind. They are also all designed with developers in mind.   Steve Ballmer recently ranted "It's the developers!" That's why it is relatively quick to build apps using MS tools. Clearly, MS knows that while we usually enjoy building technology solutions, we are here to make money. And we need tools that accelerate our time to market without compromising the power and quality of our solutions.   So, yeah, I am sucking up I guess. But I love Microsoft Development. Thank you, Microsoft, for providing the plethora of great development tools.    P.S. (but please slow down a bit…I'm having trouble keeping up!)

  Read the article

• How to force a new Notification in notify-osd to show up without waiting for the earlier one to exit?

  - by Nirmik

  I have made a script(and a .desktop shortcut leading to this script) for starting and stoping xampp... It checks the status of xampp and accordingly either starts or stops xampp. Now i have assigned a notification as soon as the script is started to display "Starting xampp..." or "Stopping xampp..." and then when xampp is started or stopped,it displays "Xampp started..." or "Xampp stopped..." I've used notify-send to show notification as seen in the script below Now the thing is that here,the second notification waits for the 1st one to disappear and then pops up even if xampp has started/stopped. I want the new notification to appear immediately by forcing the earlier one to exit before the completion of its life-cycle. This can be seen to take plce when you activate/deactivate wireless/networking immediately... For example the "Wireless enabled" comes up on selecting enable wireless and if you immediately select disable wireless,the "Wireless disabled" notification comes up without waiting for "Wireless enabled" notification to complete its life-cycle. So how do i achieve this? #!/bin/sh SERVICE='proftpd' if ps ax | grep -v grep | grep $SERVICE /dev/null then notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "Stopping XAMPP..." && gksudo /opt/lampp/lampp stop && notify-send -i /opt/lampp/htdocs/xampp/img/logo- small.gif "XAMPP Stoped." else notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "Starting XAMPP..." && gksudo /opt/lampp/lampp start && notify-send -i /opt/lampp/htdocs/xampp/img/logo-small.gif "XAMPP Started." fi On the man page for notify-send I found --urgency=LEVEL or -u where levels are low, normal, critical. Is this of any use? making it critical? Also I tried it with the command- notify-send -u=critical"Testing" but that dint work...it gives the error- Unknown urgency criticalTesting specified. Known urgency levels: low, normal, critical. or if I give the command notify-send -u=LOW"Testing" it gives me error missing argument to -u Any relation??

  Read the article

• Joy! | Important Information About Your iPad 3G

  - by Jeff Julian

  Looks like I was one of the lucky 114,000 who AT&T lost their email to “hackers”.  Why is “hackers” in “double quotes”.  I can just imagine some executive at AT&T in their “Oh No, We Messed Up Meeting” saying, what happened?  Then someone replied, well we have had a breach and “hackers” broke in (using the quote in the air gesture) and stole our iPad 3G customers emails. Oh well, I am sure my email has been sold and sold again by many different vendors, why not AT&T now.  At least Dorothy Attwood could have gave us her email to give to someone else instead of blinking it through a newsletter system. June 13, 2010 Dear Valued AT&T Customer, Recently there was an issue that affected some of our customers with AT&T 3G service for iPad resulting in the release of their customer email addresses. I am writing to let you know that no other information was exposed and the matter has been resolved.  We apologize for the incident and any inconvenience it may have caused. Rest assured, you can continue to use your AT&T 3G service on your iPad with confidence. Here’s some additional detail: On June 7 we learned that unauthorized computer “hackers” maliciously exploited a function designed to make your iPad log-in process faster by pre-populating an AT&T authentication page with the email address you used to register your iPad for 3G service.  The self-described hackers wrote software code to randomly generate numbers that mimicked serial numbers of the AT&T SIM card for iPad – called the integrated circuit card identification (ICC-ID) – and repeatedly queried an AT&T web address.   When a number generated by the hackers matched an actual ICC-ID, the authentication page log-in screen was returned to the hackers with the email address associated with the ICC-ID already populated on the log-in screen. The hackers deliberately went to great efforts with a random program to extract possible ICC-IDs and capture customer email addresses.  They then put together a list of these emails and distributed it for their own publicity. As soon as we became aware of this situation, we took swift action to prevent any further unauthorized exposure of customer email addresses.  Within hours, AT&T disabled the mechanism that automatically populated the email address. Now, the authentication page log-in screen requires the user to enter both their email address and their password. I want to assure you that the email address and ICC-ID were the only information that was accessible. Your password, account information, the contents of your email, and any other personal information were never at risk.  The hackers never had access to AT&T communications or data networks, or your iPad.  AT&T 3G service for other mobile devices was not affected. While the attack was limited to email address and ICC-ID data, we encourage you to be alert to scams that could attempt to use this information to obtain other data or send you unwanted email. You can learn more about phishing by visiting the AT&T website. AT&T takes your privacy seriously and does not tolerate unauthorized access to its customers’ information or company websites.   We will cooperate with law enforcement in any investigation of unauthorized system access and to prosecute violators to the fullest extent of the law. AT&T acted quickly to protect your information – and we promise to keep working around the clock to keep your information safe.  Thank you very much for your understanding, and for being an AT&T customer. Sincerely, Dorothy Attwood Senior Vice President, Public Policy and Chief Privacy Officer for AT&T Technorati Tags: AT&T,iPad 3G,Email

  Read the article

< Previous Page | 457 458 459 460 461 462 463 464 465 466 467 468  | Next Page >