Search Results

Search found 12826 results on 514 pages for 'third party controls'.

Page 464/514 | < Previous Page | 460 461 462 463 464 465 466 467 468 469 470 471  | Next Page >

• Internal drives vs USB-3 with external SSD or eSata with External SSD

  - by normstorm

  I have a need to carry VMWare Virtual Machines with me for work. These are very large files (each VM is 20GB or more) and I carry around about 40 to 50 VM's to simulate different software configurations for different client needs. Key: they won't fit on the internal hard drive of my current laptop. I currently execute the VM's from an external 7200RPM 2.5" USB-2 drive. I keep copies of the VM's on other 5400 external USB-2 drives. The VM's work from this drive, but they are slow, costing me much time and frustration. It can take upwards of 30 minutes just to make a copy of one of the VM's. They can take upwards of 10-15 minutes to fully launch and then they operate sluggishly. I am buying a new laptop (Core I7, 8GB RAM and other high-end specs). I intend to buy an SSD for the O/S volume (C:). This SSD will not be large enough to hold the VM's. I have always wanted a second internal hard drive to operate the VM's. To have two hard drives, though, I am finding that I will have to go to a 17" laptop which would be bulky/heavy. I am instead considering purchasing a 15" laptop with either an eSATA port or USB-3 ports and then purchasing two external drives. One of the drives might be an external SSD (maybe OCX brand) for operating the VM's and the other a 7400RPM 1TB hard drive for carrying around the VM's not currently in use. The question is which options would give me the biggest bang for the buck and the weight: 1) 2nd Internal SSD hard drive. This would mean buying a 17" laptop with two drive "bays". The first bay would hold an SSD drive for the C: drive. I would leave the first bay empty from the manufacture and then purchase/install an aftermarket SSD drive. This second SSD drive would have to be very large (256 GB), which would be expensive. I would still also need another external hard drive for carrying around the VM's not in use. 2) 2nd internal hard drive - 7400 RPM. Again, a 17" laptop would be required, but there are models available with on SSD drive for the C: drive and a second 7200 RPM hard drives. The second drive could probably be large enough to hold the VM's in use as well as those not in use. But would it be fast enough to drive the VM's? 3) USB-3 with External SSD. I could buy a 15" laptop with an SSD drive for the C: drive and a second hard drive for general files. I would operate the VM's from an external USB-3 SSD drive and have a third USB-3 external 7200 RPM drive for holding the VM's not in use. 4) eSATA with External SSD. Ditto, just eSATA instead of USB-3 5) USB-3 with External 7400 RPM drive. Ditto, but the drive running the VM's would be USB-3 attached 7400 RPM drives rather than SSD. 6) eSATA with External 7400 RPM drive. Dittor, but the drive running the VM's would be eSATA attached 7400 RPM drives rather than SSD. Any thoughts on this and any creative solutions?

  Read the article

• Wireless AAA for a small, bandwidth-limited hotel.

  - by Anthony Hiscox

  We (the tech I work with and myself) live in a remote northern town where Internet access is somewhat of a luxury, and bandwidth is quite limited. Here, overage charges ranging from few hundreds, to few thousands of dollars a month, is not uncommon. I myself incur regular monthly charges just through my regular Internet usage at home (I am allowed 10G for $60CAD!) As part of my work, I have found myself involved with several hotels that are feeling this. I know that I can come up with something to solve this problem, but I am relatively new to system administration and I don't want my dreams to overcome reality. So, I pass these ideas on to you, those with much more experience than I, in hopes you will share some of your thoughts and concerns. This system must be cost effective, yes the charges are high here, but the trust in technology is the lowest I've ever seen. Must be capable of helping client reduce their usage (squid) Allow a limited (throughput and total usage) amount of free Internet, as this is often franchise policy. Allow a user to track their bandwidth usage Allow (optional) higher speed and/or usage for an additional charge. This fee can be obtained at the front desk on checkout and should not require the use of PayPal or Credit Card. Unfortunately some franchises have ridiculous policies that require the use of a third party remote service to authenticate guests to your network. This means WPA is out, and it also means that I do not auth before Internet usage, that will be their job. However, I do require the ABILITY to perform authentication for Internet access if a hotel does not have this policy. I will still have to track bandwidth (under a guest account by default) and provide the same limiting, however the guest often will require a complete 'unlimited' access, in terms of existence, not throughput. Provide firewalling capabilities for hotels that have nothing, Office, and Guest network segregation (some of these guys are running their office on the guest network, with no encryption, and a simple TOS to get on!) Prevent guests from connecting to other guests, however provide a means to allow this to happen. IE. Each guest connects to a page and allows the other guest, this writes a iptables rule (with python-netfilter) and allows two rooms to play a game, for instance. My thoughts on how to implement this. One decent box (we'll call it a router now) with a lot of ram, and 3 NIC's: Internet Office Guests (AP's + In Room Ethernet) Router Firewall Rules Guest can talk to router only, through which they are routed to where they need to go, including Internet services. Office can be used to bridge Office to Internet if an existing solution is not in place, otherwise, it simply works for a network accessible web (webmin+python-webmin?) interface. Router Software: OpenVZ provides virtualization for a few services I don't really trust. Squid, FreeRADIUS and Apache. The only service directly accessible to guests is Apache. Apache has mod_wsgi and django, because I can write quickly using django and my needs are low. It also potentially has the FreeRADIUS mod, but there seems to be some caveats with this. Firewall rules are handled on the router with iptables. Webmin (or a custom django app maybe) provides abstracted control over any features that the staff may need to access. Python, if you haven't guessed it's the language I feel most comfortable in, and I use it for almost everything. And finally, has this been done, is it a overly massive project not worth taking on for one guy, and/or is there some tools I'm missing that could be making my life easier? For the record, I am fairly good with Python, but not very familiar with many other languages (I can struggle through PHP, it's a cosmetic issue there). I am also an avid linux user, and comfortable with config files and command line. Thank you for your time, I look forward to reading your responses. Edit: My apologies if this is not a Q&A in the sense that some were expecting, I'm just looking for ideas and to make sure I'm not trying to do something that's been done. I'm looking at pfSense now as a possible start for what I need.

  Read the article

• Sharing the same `ssh-agent` among multiple login sessions

  - by intuited

  Is there a convenient way to ensure that all logins from a given user (ie me) use the same ssh-agent? I hacked out a script to make this work most of the time, but I suspected all along that there was some way to do it that I had just missed. Additionally, since that time there have been amazing advances in computing technology, like for example this website. So the goal here is that whenever I log in to the box, regardless of whether it's via SSH, or in a graphical session started from gdm/kdm/etc, or at a console: if my username does not currently have an ssh-agent running, one is started, the environment variables exported, and ssh-add called. otherwise, the existing agent's coordinates are exported in the login session's environment variables. This facility is especially valuable when the box in question is used as a relay point when sshing into a third box. In this case it avoids having to type in the private key's passphrase every time you ssh in and then want to, for example, do git push or something. The script given below does this mostly reliably, although it botched recently when X crashed and I then started another graphical session. There might have been other screwiness going on in that instance. Here's my bad-is-good script. I source this from my .bashrc. # ssh-agent-procure.bash # v0.6.4 # ensures that all shells sourcing this file in profile/rc scripts use the same ssh-agent. # copyright me, now; licensed under the DWTFYWT license. mkdir -p "$HOME/etc/ssh"; function ssh-procure-launch-agent { eval `ssh-agent -s -a ~/etc/ssh/ssh-agent-socket`; ssh-add; } if [ ! $SSH_AGENT_PID ]; then if [ -e ~/etc/ssh/ssh-agent-socket ] ; then SSH_AGENT_PID=`ps -fC ssh-agent |grep 'etc/ssh/ssh-agent-socket' |sed -r 's/^\S+\s+(\S+).*$/\1/'`; if [[ $SSH_AGENT_PID =~ [0-9]+ ]]; then # in this case the agent has already been launched and we are just attaching to it. ##++ It should check that this pid is actually active & belongs to an ssh instance export SSH_AGENT_PID; SSH_AUTH_SOCK=~/etc/ssh/ssh-agent-socket; export SSH_AUTH_SOCK; else # in this case there is no agent running, so the socket file is left over from a graceless agent termination. rm ~/etc/ssh/ssh-agent-socket; ssh-procure-launch-agent; fi; else ssh-procure-launch-agent; fi; fi; Please tell me there's a better way to do this. Also please don't nitpick the inconsistencies/gaffes ( eg putting var stuff in etc ); I wrote this a while ago and have since learned many things.

  Read the article

• PC: Quick Freeze, then BSOD, then forced reboot, then freezes again

  - by cr0z3r

  Lately I have been experiencing a weird issue. My PC will hang for a second and then BSOD - it stays there, so I have to reboot. Once Windows starts again and I'm logged in, after 1-10min it freezes again, this time without BSOD. RECAP: 1 second freeze BSOD, hangs there I have to force-reboot Once PC rebooted, I log back into Windows second freeze between a 1-10min range, no BSOD (alternatively, I get a freeze with a constant sound/noise, no BSOD) I contacted my PC provider, who told me my graphics-card might be flawed (Quadro 4000), so I used a Quadro 2000 that they lend me. The issue still occurred. The issue now seemed to belong to a flawed RAM module. Following my provider's steps, I removed all but the first from the left column and kept using my PC for a week or so without any issues. I then added the bottom-right module, and so on, until all modules were back inside - I had no problems. Now it seemed that a simple take-out-put-back-in of the RAM modules had fixed the issue. However, after a few months, the issue was back. I redid all the RAM-swapping I had done before, and concluded that the lower-right module was flawed. My provider changed it for another, and everything was great until now. My PC froze again for barely a second, hanged on a BSOD, I rebooted it, logged-in to Windows to get a freeze (without BSOD or reboot) 40 seconds later. Something worth noting, is that every time I reboot after the BSOD, it is something within Chrome that freezes my PC (e.g. this time I clicked the "restore" button as Chrome mentioned it had exited unexpectedly - from the previous freeze obviously - and it instantly froze). Finally, the Event Viewer lists 2 critical events in the past hour as "ID: 41, Type: Kernel-Power". PC-Specs: http://i.imgur.com/VZpbr.jpg Previous Dump-files: https://dl.dropbox.com/u/716600/DumpFiles_08_2012.zip I would like to thank anybody in advance for your help. You're great. UPDATE 1: I realized that I did not mention an awkward fact about this issue. After I have gotten the 1-sec freeze followed by a BSOD, after I rebooted because the BSOD hanged, and after I logged back in to get another (this time, eternal) freeze and rebooted once again, the PC does not boot back up. The power-light is on, but my monitor says "no signal", as if the PC wouldn't really be turned on. This truly seems a like a power-related issue, doesn't it? UPDATE 2: I just got a freeze, but without BSOD. My screen froze (while on Chrome, which is starting to seem suspicious to me) with an ongoing sound/noise. I had to force-reboot my PC. I would say this is a graphics-card issue, but this issue also happened when I was using the Quadro 2000 from my provider. UPDATE 3: I just got a BSOD while trying to render something (quite heavy, actually) in 3ds Max 2012. I left the BSOD "running", as it said it was writing dump files to disk. However, the percentage number stayed at 0, so after 15 minutes I force-rebooted. I then used the software WhoCrashed (thank you Dave) which reported the following from the C:\Windows\Memory.dmp file: On Thu 22.11.2012 22:13:45 GMT your computer crashed crash dump file: C:\Windows\memory.dmp uptime: 01:05:27 This was probably caused by the following module: Unknown () Bugcheck code: 0x124 (0x0, 0xFFFFFA80275AC028, 0xF200001F, 0x100B2) Error: WHEA_UNCORRECTABLE_ERROR Bug check description: This bug check indicates that a fatal hardware error has occurred. This bug check uses the error data that is provided by the Windows Hardware Error Architecture (WHEA). This is likely to be caused by a hardware problem problem. This problem might be caused by a thermal issue. A third party driver was identified as the probable root cause of this system error. It is suggested you look for an update for the following driver: Unknown . Google query: Unknown WHEA_UNCORRECTABLE_ERROR

  Read the article

• DNS request timed out. timeout was 2 seconds

  - by sahil007

  i had setup bind dns server on centos. from local lan it will work fine but from remote when i tried to nslookup ..it will give reply like "DNS request timed out...timeout was 2 seconds." what is the problem? this is my bind config---- // Red Hat BIND Configuration Tool options { directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; query-source address * port 53; }; controls { inet 127.0.0.1 allow {localhost; } keys {rndckey; }; }; acl internals { 127.0.0.0/8; 192.168.0.0/24; 10.0.0.0/8; }; view "internal" { match-clients { internals; }; recursion yes; zone "mydomain.com" { type master; file "mydomain.com.zone"; }; zone "0.168.192.in-addr.arpa" { type master; file "0.168.192.in-addr.arpa.zone"; }; zone "." IN { type hint; file "named.root"; }; zone "localdomain." IN { type master; file "localdomain.zone"; allow-update { none; }; }; zone "localhost." IN { type master; file "localhost.zone"; allow-update { none; }; }; zone "0.0.127.in-addr.arpa." IN { type master; file "named.local"; allow-update { none; }; }; zone "0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa." I N { type master; file "named.ip6.local"; allow-update { none; }; }; zone "255.in-addr.arpa." IN { type master; file "named.broadcast"; allow-update { none; }; }; zone "0.in-addr.arpa." IN { type master; file "named.zero"; allow-update { none; }; }; }; view "external" { match-clients { any; }; recursion no; zone "mydomain.com" { type master; file "mydomain.com.zone"; // file "/var/named/chroot/var/named/mydomain.com.zone"; }; zone "0.168.192.in-addr.arpa" { type master; file "0.168.192.in-addr.arpa.zone"; }; }; include "/etc/rndc.key";

  Read the article

• Consistent PHP _SERVER variables between Apache and nginx?

  - by Alix Axel

  I'm not sure if this should be asked here or on ServerFault, but here it goes... I am trying to get started on nginx with PHP-FPM, but I noticed that the server block setup I currently have (gathered from several guides including the nginx Pitfalls wiki page) produces $_SERVER variables that are different from what I'm used to seeing in Apache setups. After spending the last evening trying to "fix" this, I decided to install Apache on my local computer and gather the variables that I'm interested in under different conditions so that I could try and mimic them on nginx. The Apache setup I've on my computer has only one mod_rewrite rule: RewriteEngine On RewriteCond %{SCRIPT_FILENAME} !-f RewriteCond %{SCRIPT_FILENAME} !-d RewriteRule ^(.*)$ /index.php/$1 [L] And these are the values I get for different request URIs (left is Apache, right is nginx): localhost/ - http://www.mergely.com/GnzBHRV1/ localhost/foo/bar/baz/?foo=bar - http://www.mergely.com/VwsT8oTf/ localhost/index.php/foo/bar/baz/?foo=bar - http://www.mergely.com/VGEFehfT/ What configuration directives would allow me to get similar values on requests handled by nginx? My current configuration in nginx is: server { listen 80; listen 443 ssl; server_name default; ssl_certificate /etc/nginx/certificates/dummy.crt; ssl_certificate_key /etc/nginx/certificates/dummy.key; root /var/www/default/html; index index.php index.html; autoindex on; location / { try_files $uri $uri/ /index.php; } location ~ /(?:favicon[.]ico|robots[.]txt)$ { log_not_found off; } location ~* [.]php { #try_files $uri =404; include fastcgi_params; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; fastcgi_split_path_info ^(.+[.]php)(/.+)$; } location ~* [.]ht { deny all; } } And my fastcgi_params file looks like this: fastcgi_param PATH_INFO $fastcgi_path_info; fastcgi_param PATH_TRANSLATED $document_root$fastcgi_path_info; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; fastcgi_param HTTPS $https; I know that the try_files $uri =404; directive is commented and that it is a security vulnerability but, if I uncomment it, the third request (localhost/index.php/foo/bar/baz/?foo=bar) will return a 404. It's also worth noting that my PHP cgi.fix_pathinfo in On (contrary to what some of the guides recommend), if I try to set it to Off, I'm presented with a "Access denied." message on every PHP request. I'm running PHP 5.4.8 and nginx/1.1.19. I don't know what else to try... Help?

  Read the article

• Multiple Homed Windows 2008 Server / Windows 7 Client

  - by Daniel Scott

  I have a small Windows 2008 network, with some Windows 7 clients. The clients are both laptops with docking stations and I would like them to communicate with the Windows 2008 server (for filesharing) through the wired network whilst they're docked. Internet connectivity for all machines (clients and server) is via a Wireless LAN, so the wireless adapter in the Windows 7 clients stays active while they're docked. When the laptops are un-docked, it would be nice to still be able to contact the windows 2008 server for print sharing (and slower file sharing) - hence the server also being on the wireless LAN. The windows 2008 server is running Active Directory, DHCP and DNS. It controls DHCP leases on the wired network and holds the DNS records for "myserver.mycompany.local", which is what the filesharing clients connect to. Ideally I'd like the DNS records to return the wired IP first so that this is the address that the laptops will attempt initially - but there doesn't seem to be a way to do that? At present the server's IP on the wireless LAN comes out of an nslookup above the wired Lan IP. The multi-homing works perfectly - but in the wrong order! Switch on the wireless lan and ping myserver and it goes to the wireless IP. Disable the wireless on the client and do the same ping again and after a couple of seconds it starts pinging the wired address. Does anyone have any suggestions on how to make this work in a predictable order? - or even if it can work. Alternative 1? If it can't work, then would this work: Remove the wireless adapter from the server, put a wireless router/bridge on the wired network (set up to route to/from the wireless LAN's subnet), then configure the clients with two routes to the (now) single IP of the server with metrics favouring direct communication over the wired LAN first? Alternative 2? Should I instead single-home the laptops so all of their connectivity is via the wired-LAN while they're docked? (and route via the windows 2008 server - or a dedicated wireless bridge/router)? My concern here is that I'd like undocking to be seamless - and if the clients are in the middle of downloading something from the internet I wouldn't want whatever they're doing interupted as they switch IP addresses onto the Wireless network. Perhaps this isn't the case and I'm concerned over nothing? Any thoughts? :) UPDATE I seem to have cracked it (at least DNS entries come out in the order I hope for - and pinging the server with various combinations of wired, wireless and both interfaces enabled uses the IP I want) ... I set the binding order of the NICs on the Server (which is acting as Domain Controller, DHCP and DNS server) so that the Wired NIC is before the Wireless adapter. (Start -- type "Network Interfaces" -- Select "View Network Connections" -- Press Alt to show classic dropdown menus -- Advanced -- Advanced Settings) Now, an nslookup (from the client) of the server's hostname returns the Wired IP first, followed by the Wireless IP. The wired IP now seems to be used whenever it's contactable. Incidentally, the metrics on the wired and wireless routes (on the client) also favour the wired LAN (based on Windows' automatically assigned metrics) - but this was always the case, even when I was having trouble getting the wired IP to be "favoured". I'm not entirely sure if this is coincidence - or if a DNS server running on Windows, handing back IP addresses for itself does actually take the binding order of it's own network interfaces into account? It would be interesting to hear from someone who can confirm or deny that (or confirm that the binding order on the server plays a role for some other reason?)

  Read the article

• Yet again: "This device can perform faster" (Samsung Galaxy Tab 2)

  - by Mike C

  I've been doing a lot of research with no reasonable solution. Please excuse the length of my post. When I plug my Galaxy Tab 2 (7" / Wi-Fi only / Android ICS) into my Windows 7 64-bit machine, I (almost always) get this warning popup that "This device can perform faster." And in fact, transfers onto the Tab in this mode are slow. The two times I've been able to get a high-speed connection, the transfer has occurred at the expected speed. I just don't know what to do to get that high-speed transfer. (The first time I did, it was the first time I connected the Tab; the second time I did, I was fiddling around and unplugging/plugging in again.) That popup is telling me that the device is USB2, but that it thinks I've connected to a USB1 port. In fact, every USB port (there are ten) on this system is USB2. It's an ASUS M3A78-EMH mobo from late 2008. I'm not sure what the chipset is; the CPU is an AMD Athlon 4850e, but I've seen this message reported for non-AMD systems. (Every mobo reference I've seen in reports on this has been for Asus, but of course most reporters aren't reporting that info at all.) The Windows 7 installation is just a couple weeks old (I had a disk crash) but I saw the same warning on the WinXP/64 that was installed previously. In Device Manager, there are two "Standard Enhanced PCI to USB Host Controller" nodes which are the actual high-speed controllers. There are also five "Standard OpenHCD USB Host Controller" nodes, which I have determined are virtual USB1 controllers embedded in the "Enhanced" controllers. (In Device Manager, I'm using View|Devices by Connection.) My high-speed thumb drives, external disks, and iPod all show up as subnodes of the "Enhanced" controllers; the keyboard, mouse, and USB speakers under the "OpenHCD" ones -- and this is true no matter which ports these devices are plugged into. The Tab shows up under an OpenHCD node, unsurprisingly. It appears as a threesome: a top-level "Mobile USB Composite device" with two subs: "Galaxy Tab 2" and "Mobile USB Modem." (I have no idea what the modem device implies or how I might use it, but I don't care about it either: I just want the Tab to reliably connect at high speed.) On the Tab, the USB support has a switch between PTP and MTP, the latter being the default, and the preferred mode for me (as I'm usually hooking it up for music synch). I have tried, however, connecting it as PTP, and it still connects as USB 1. (As PTP, only the "Galaxy Tab 2" device appears -- no Composite, no Modem.) If it's plugged in as MTP and I change the setting to PTP, Windows unloads and reloads the device, and voila: The Tab appears under an "Enhanced" node, but eventually re-loads again to show a exclamation icon on the device; Properties then shows "This device cannot start." Same response if I plug it in as PTP and then change to MTP; in this case, only the Tab itself shows the exclamation, not the other two devices. One thing I have not tried, and really would prefer to avoid, is installing the "beta" chipset driver available on the Asus website, which is dated 2009. Windows tells me it has the most up-to-date drivers for the Tab, and for the chipset, and I'm inclined to believe that. I suspect the problem is with the Samsung drivers, or possibly the hardware. One suggestion I saw elsewhere which might, possibly, pertain is to ensure the USB cable is properly shielded; however, the Tab has one of those misbegotten 30-pin, not-quite-an-iPod connectors; I don't know if I could find a 3rd party one. It seems unlikely that this cable is improperly shielded, tho. (Is there a way to test that?) So, my question is: does anyone know how to get this working as one might reasonably expect it to?

  Read the article

• php-fpm + persistent sockets = 502 bad gateway

  - by leeoniya

  Put on your reading glasses - this will be a long-ish one. First, what I'm doing. I'm building a web-app interface for some particularly slow tcp devices. Opening a socket to them takes 200ms and an fwrite/fread cycle takes another 300ms. To reduce the need for both of these actions on each request, I'm opening a persistent tcp socket which reduces the response time by the aforementioned 200ms. I was hoping PHP-FPM would share the persistent connections between requests from different clients (and indeed it does!), but there are some issues which I havent been able to resolve after 2 days of interneting, reading logs and modifying settings. I have somewhat narrowed it down though. Setup: Ubuntu 13.04 x64 Server (fully updated) on Linode PHP 5.5.0-6~raring+1 (fpm-fcgi) nginx/1.5.2 Relevent config: nginx worker_processes 4; php-fpm/pool.d pm = dynamic pm.max_children = 2 pm.start_servers = 2 pm.min_spare_servers = 2 Let's go from coarse to fine detail of what happens. After a fresh start I have 4x nginx processes and 2x php5-fpm processes waiting to handle requests. Then I send requests every couple seconds to the script. The first take a while to open the socket connection and returns with the data in about 500ms, the second returns data in 300ms (yay it's re-using the socket), the third also succeeds in about 300ms, the fourth request = 502 Bad Gateway, same with the 5th. Sixth request once again returns data, except now it took 500ms again. The process repeats for several cycles after which every 4 requests result in 2x 502 Bad Gateways and 2x 500ms Data responses. If I double all the fpm pool values and have 4x php-fpm processes running, the cycles settles in with 4x successful 500ms responses followed by 4x Bad Gateway errors. If I don't use persistent sockets, this issue goes away but then every request is 500ms. What I suspect is happening is the persistent socket keeps each php-fpm process from idling and ties it up, so the next one gets chosen until none are left and as they error out, maybe they are restarted and become available on the next round-robin loop ut the socket dies with the process. I haven't yet checked the 'slowlog', but the nginx error log shows lots of this: *188 recv() failed (104: Connection reset by peer) while reading response header from upstream, client:... All the suggestions on the internet regarding fixing nginx/php-fpm/502 bad gateway relate to high load or fcgi_pass misconfiguration. This is not the case here. Increasing buffers/sizes, changing timeouts, switching from unix socket to tcp socket for fcgi_pass, upping connection limits on the system....none of this stuff applies here. I've had some other success with setting pm = ondemand rather than dynamic, but as soon as the initial fpm-process gets killed off after idling, the persistent socket is gone for all subsequent php-fpm spawns. For the php script, I'm using stream_socket_client() with a STREAM_CLIENT_PERSISTENT flag. A while/stream_select() loop to detect socket data and fread($sock, 4096) to grab the data. I don't call fclose() obviously. If anyone has some additional questions or advice on how to get a persistent socket without tying up the php-fpm processes beyond the request completion, or maybe some other things to try, I'd appreciate it. some useful links: Nginx + php-fpm - recv() error Nginx + php-fpm "504 Gateway Time-out" error with almost zero load (on a test-server) Nginx + PHP-FPM "error 104 Connection reset by peer" causes occasional duplicate posts http://www.linuxquestions.org/questions/programming-9/php-pfsockopen-552084/ http://stackoverflow.com/questions/14268018/concurrent-use-of-a-persistent-php-socket http://devzone.zend.com/303/extension-writing-part-i-introduction-to-php-and-zend/#Heading3 http://stackoverflow.com/questions/242316/how-to-keep-a-php-stream-socket-alive http://php.net/manual/en/install.fpm.configuration.php https://www.google.com/search?q=recv%28%29+failed+%28104:+Connection+reset+by+peer%29+while+reading+response+header+from+upstream+%22502%22&ei=mC1XUrm7F4WQyAHbv4H4AQ&start=10&sa=N&biw=1920&bih=953&dpr=1

  Read the article

• How to install pip/easy_install on debian 6 for python3.2

  - by atomAltera

  I'm trying to install pip or setup tools form python 3.2 in debian 6. First case: apt-get install python3-pip...OK python3 easy_install.py webob Searching for webob Reading http://pypi.python.org/simple/webob/ Reading http://webob.org/ Reading http://pythonpaste.org/webob/ Best match: WebOb 1.2.2 Downloading http://pypi.python.org/packages/source/W/WebOb/WebOb-1.2.2.zip#md5=de0f371b46554709ce5b93c088a11cae Processing WebOb-1.2.2.zip Traceback (most recent call last): File "easy_install.py", line 5, in <module> main() File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 1931, in main with_ei_usage(lambda: File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 1912, in with_ei_usage return f() File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 1935, in <lambda> distclass=DistributionWithoutHelpCommands, **kw File "/usr/local/lib/python3.2/distutils/core.py", line 148, in setup dist.run_commands() File "/usr/local/lib/python3.2/distutils/dist.py", line 917, in run_commands self.run_command(cmd) File "/usr/local/lib/python3.2/distutils/dist.py", line 936, in run_command cmd_obj.run() File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 368, in run self.easy_install(spec, not self.no_deps) File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 608, in easy_install return self.install_item(spec, dist.location, tmpdir, deps) File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 638, in install_item dists = self.install_eggs(spec, download, tmpdir) File "/usr/lib/python3/dist-packages/setuptools/command/easy_install.py", line 799, in install_eggs unpack_archive(dist_filename, tmpdir, self.unpack_progress) File "/usr/lib/python3/dist-packages/setuptools/archive_util.py", line 67, in unpack_archive driver(filename, extract_dir, progress_filter) File "/usr/lib/python3/dist-packages/setuptools/archive_util.py", line 154, in unpack_zipfile data = z.read(info.filename) File "/usr/local/lib/python3.2/zipfile.py", line 891, in read with self.open(name, "r", pwd) as fp: File "/usr/local/lib/python3.2/zipfile.py", line 980, in open close_fileobj=not self._filePassed) File "/usr/local/lib/python3.2/zipfile.py", line 489, in __init__ self._decompressor = zlib.decompressobj(-15) AttributeError: 'NoneType' object has no attribute 'decompressobj' Second case: from http://pypi.python.org/pypi/distribute#installation-instructions python3 distribute_setup.py Downloading http://pypi.python.org/packages/source/d/distribute/distribute-0.6.28.tar.gz Extracting in /tmp/tmpv6iei2 Traceback (most recent call last): File "distribute_setup.py", line 515, in <module> main(sys.argv[1:]) File "distribute_setup.py", line 511, in main _install(tarball, _build_install_args(argv)) File "distribute_setup.py", line 73, in _install tar = tarfile.open(tarball) File "/usr/local/lib/python3.2/tarfile.py", line 1746, in open raise ReadError("file could not be opened successfully") tarfile.ReadError: file could not be opened successfully Third case: from http://pypi.python.org/pypi/distribute#installation-instructions tar -xzvf distribute-0.6.28.tar.gz cd distribute-0.6.28 python3 setup.py install Before install bootstrap. Scanning installed packages No setuptools distribution found running install running bdist_egg running egg_info writing distribute.egg-info/PKG-INFO writing top-level names to distribute.egg-info/top_level.txt writing dependency_links to distribute.egg-info/dependency_links.txt writing entry points to distribute.egg-info/entry_points.txt reading manifest file 'distribute.egg-info/SOURCES.txt' reading manifest template 'MANIFEST.in' writing manifest file 'distribute.egg-info/SOURCES.txt' installing library code to build/bdist.linux-x86_64/egg running install_lib running build_py copying distribute.egg-info/PKG-INFO -> build/bdist.linux-x86_64/egg/EGG-INFO copying distribute.egg-info/SOURCES.txt -> build/bdist.linux-x86_64/egg/EGG-INFO copying distribute.egg-info/dependency_links.txt -> build/bdist.linux-x86_64/egg/EGG-INFO copying distribute.egg-info/entry_points.txt -> build/bdist.linux-x86_64/egg/EGG-INFO copying distribute.egg-info/top_level.txt -> build/bdist.linux-x86_64/egg/EGG-INFO creating 'dist/distribute-0.6.28-py3.2.egg' and adding 'build/bdist.linux-x86_64/egg' to it Traceback (most recent call last): File "setup.py", line 220, in <module> scripts = scripts, File "/usr/local/lib/python3.2/distutils/core.py", line 148, in setup dist.run_commands() File "/usr/local/lib/python3.2/distutils/dist.py", line 917, in run_commands self.run_command(cmd) File "/usr/local/lib/python3.2/distutils/dist.py", line 936, in run_command cmd_obj.run() File "build/src/setuptools/command/install.py", line 73, in run self.do_egg_install() File "build/src/setuptools/command/install.py", line 93, in do_egg_install self.run_command('bdist_egg') File "/usr/local/lib/python3.2/distutils/cmd.py", line 313, in run_command self.distribution.run_command(command) File "/usr/local/lib/python3.2/distutils/dist.py", line 936, in run_command cmd_obj.run() File "build/src/setuptools/command/bdist_egg.py", line 241, in run dry_run=self.dry_run, mode=self.gen_header()) File "build/src/setuptools/command/bdist_egg.py", line 542, in make_zipfile z = zipfile.ZipFile(zip_filename, mode, compression=compression) File "/usr/local/lib/python3.2/zipfile.py", line 689, in __init__ "Compression requires the (missing) zlib module") RuntimeError: Compression requires the (missing) zlib module zlib1g-dev installed Help me please

  Read the article

• IP Micro-outages, telephone micro-outages, and CATV micro-outages

  - by Michael Graff

  This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

  Read the article

• Accessing resources on localhost using domain credentials

  - by jas

  I'm trying to set up Team Foundation Server 2010, Sharepoint Server 2010 and Report Server 2008R2. I apologize for how long my question/problem is but I'm really lost on where to even look so am being as descriptive as possible in hopes that I'm making sense. The goal: Since developers can be inside or outside the firewall there needs to be a single http point of entry to TFS that works regardless of which side of the firewall you are and needs to work with external access to SharePoint and Report Server. Meaning we have it set up in DNS so buildserver.mydomain.com: points to the build service box which contains all of the services listed at the top of this post and specific services are defined/located by the port number. This is working great on every machine inside and out except for from the build server itself. All services must be able to work using external URLs. If I use http:// buildserver.mydomain.com:4800/tfs (the external URL) from my notebook which is behind the firewall I'm able to login with my domain credentials as expected. If the other developer points to the same URL from their home which isn't on the domain they are also able to login using their domain credentials. However if I am directly on buildserver and call SharePoint, TFS or Reporting Server from (i.e. http:// buildserver.mydomain.com:4800) itself using the external URL, I am prompted for a username and password. Entering my domain credentials results in another prompt to enter my credentials again. It will prompt three times regardless of which credentials are used (I have rights as a domain admin) and then after the third prompt directs me to a blank white page as though access was denied. There are no errors displayed on the page and nothing ends up in the event viewer. From buildserver if i use just the host name (the internal URL), then I'm prompted a single time for credentials and it works. i.e. http:// buildserver:4800/tfs works from the server itself. The behavior is identical for any service requiring authentication. Meaning from the box itself Sharepoint Central Admin, SharePoint WebApp, TFS, TFS Web Access, Report Server and Report Manager all fail using the external URL but will succeed if called using the interal URL. So the problem comes into play when configuring all of the services to work together. The only way to configure TFS is locally from the server which means I must point to the internal reporting server url (http:// buildserver:4800/reports and reportServer respectively instead of http:// buildserver.domainname.com:4800 like they need to be) since external URLs aren't working from itself. If I configure TFS to use the internal URL for Report Server then creating team projects or working in the SharePoint site for the team project fails for anyone not inside the domain since their machines have no idea who http:// buildserver:/reports even is or how to resolve them. I have configured Sharepoint with Alternate Access Mappings as well as set up Report Server to listen for external URLs. The external URLs simply aren't working when called from the server itself. I hope this makes sense. Thanks for taking the time to read this rather verbose plea for help.

  Read the article

• RHCS: GFS2 in A/A cluster with common storage. Configuring GFS with rgmanager

  - by Pavel A

  I'm configuring a two node A/A cluster with a common storage attached via iSCSI, which uses GFS2 on top of clustered LVM. So far I have prepared a simple configuration, but am not sure which is the right way to configure gfs resource. Here is the rm section of /etc/cluster/cluster.conf: <rm> <failoverdomains> <failoverdomain name="node1" nofailback="0" ordered="0" restricted="1"> <failoverdomainnode name="rhc-n1"/> </failoverdomain> <failoverdomain name="node2" nofailback="0" ordered="0" restricted="1"> <failoverdomainnode name="rhc-n2"/> </failoverdomain> </failoverdomains> <resources> <script file="/etc/init.d/clvm" name="clvmd"/> <clusterfs name="gfs" fstype="gfs2" mountpoint="/mnt/gfs" device="/dev/vg-cs/lv-gfs"/> </resources> <service name="shared-storage-inst1" autostart="0" domain="node1" exclusive="0" recovery="restart"> <script ref="clvmd"> <clusterfs ref="gfs"/> </script> </service> <service name="shared-storage-inst2" autostart="0" domain="node2" exclusive="0" recovery="restart"> <script ref="clvmd"> <clusterfs ref="gfs"/> </script> </service> </rm> This is what I mean: when using clusterfs resource agent to handle GFS partition, it is not unmounted by default (unless force_unmount option is given). This way when I issue clusvcadm -s shared-storage-inst1 clvm is stopped, but GFS is not unmounted, so a node cannot alter LVM structure on shared storage anymore, but can still access data. And even though a node can do it quite safely (dlm is still running), this seems to be rather inappropriate to me, since clustat reports that the service on a particular node is stopped. Moreover if I later try to stop cman on that node, it will find a dlm locking, produced by GFS, and fail to stop. I could have simply added force_unmount="1", but I would like to know what is the reason behind the default behavior. Why is it not unmounted? Most of the examples out there silently use force_unmount="0", some don't, but none of them give any clue on how the decision was made. Apart from that I have found sample configurations, where people manage GFS partitions with gfs2 init script - https://alteeve.ca/w/2-Node_Red_Hat_KVM_Cluster_Tutorial#Defining_The_Resources or even as simply as just enabling services such as clvm and gfs2 to start automatically at boot (http://pbraun.nethence.com/doc/filesystems/gfs2.html), like: chkconfig gfs2 on If I understand the latest approach correctly, such cluster only controls whether nodes are still alive and can fence errant ones, but such cluster has no control over the status of its resources. I have some experience with Pacemaker and I'm used to that all resources are controlled by a cluster and an action can be taken when not only there are connectivity issues, but any of the resources misbehave. So, which is the right way for me to go: leave GFS partition mounted (any reasons to do so?) set force_unmount="1". Won't this break anything? Why this is not the default? use script resource <script file="/etc/init.d/gfs2" name="gfs"/> to manage GFS partition. start it at boot and don't include in cluster.conf (any reasons to do so?) This may be a sort of question that cannot be answered unambiguously, so it would be also of much value for me if you shared your experience or expressed your thoughts on the issue. How does for example /etc/cluster/cluster.conf look like when configuring gfs with Conga or ccs (they are not available to me since for now I have to use Ubuntu for the cluster)? Thanks you very much!

  Read the article

• Inconsistent file downloads of (what should be) the same file

  - by Austin A.

  I'm working on a system that archives large collections of timetstamped images. Part of the system deals with saving an image to a growing .zip file. This morning I noticed that the log system said that an image was successfully downloaded and placed in the zip file, but when I downloaded the .zip (from an apache alias running on our server), the images didn't match the log. For example, although the log said that camera 3484 captured on January 17, 2011, when I download from the apache alias, the downloaded zip file only contains images up to January 14. So, I sshed onto the server, and unzipped the file in its own directory, and that zip file has images from January 14 to today (January 17). What strikes me as odd is that this should be the exact same file as the one I downloaded from the apache alias. Other experiments: I scp-ed the file from the server to my local machine, and the zip file has the newer images. But when I use an SCP client (in this case, Fugu for OSX), I get the zip file for the older images. In short: unzipping a file on the server or after downloading through scp or after downloading through wget gives one zip file, but unzipping a file from Chrome, Firefox, or SCP client gives a different zip file, when they should be exactly the same. Unzipping on the server... [user@server ~]$ cd /export1/amos/images/2011/84/3484/00003484/ [user@server 00003484]$ ls -la total 6180 drwxr-sr-x 2 user groupname 24 Jan 17 11:20 . drwxr-sr-x 4 user groupname 36 Jan 11 19:58 .. -rw-r--r-- 1 user groupname 6309980 Jan 17 12:05 2011.01.zip [user@server 00003484]$ unzip 2011.01.zip Archive: 2011.01.zip extracting: 20110114_140547.jpg extracting: 20110114_143554.jpg replace 20110114_143554.jpg? [y]es, [n]o, [A]ll, [N]one, [r]ename: y extracting: 20110114_143554.jpg extracting: 20110114_153458.jpg (...bunch of files...) extracting: 20110117_170459.jpg extracting: 20110117_173458.jpg extracting: 20110117_180501.jpg Using the wget through apache alias. local:~ user$ wget http://example.com/zipfiles/2011/84/3484/00003484/2011.01.zip --12:38:13-- http://example.com/zipfiles/2011/84/3484/00003484/2011.01.zip => `2011.01.zip' Resolving example.com... ip.ip.ip.ip Connecting to example.com|ip.ip.ip.ip|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 6,327,747 (6.0M) [application/zip] 100% [=====================================================================================================>] 6,327,747 1.03M/s ETA 00:00 12:38:56 (143.23 KB/s) - `2011.01.zip' saved [6327747/6327747] local:~ user$ unzip 2011.01.zip Archive: 2011.01.zip extracting: 20110114_140547.jpg (... same as before...) extracting: 20110117_183459.jpg Using scp to grab the zip local:~ user$ scp user@server:/export1/amos/images/2011/84/3484/00003484/2011.01.zip . 2011.01.zip 100% 6179KB 475.3KB/s 00:13 local:~ user$ unzip 2011.01.zip Archive: 2011.01.zip extracting: 20110114_140547.jpg (...same as before...) extracting: 20110117_183459.jpg Using Fugu to download 2011.01.zip from /export1/amos/images/2011/84/3484/00003484/ gives images 20110113_090457.jpg through 201100114_010554.jpg Using Firefox to download 2011.01.zip from http://example.com/zipfiles/2011/84/3484/00003484/2011.01.zip gives images 20110113_090457.jpg through 201100114_010554.jpg Using Chrome gives same results as Firefox. Relevant section from apache httpd.conf: # ScriptAlias: This controls which directories contain server scripts. # ScriptAliases are essentially the same as Aliases, except that # documents in the realname directory are treated as applications and # run by the server when requested rather than as documents sent to the client. # The same rules about trailing "/" apply to ScriptAlias directives as to # Alias. # ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" Alias /zipfiles/ /export1/amos/images/

  Read the article

• Why would VMWare to go defunct? How to recover from/prevent it?

  - by Josh

  I am running VMWare Server 2.0.2 (Build 203138) on a dual core Intel i5 with Ubuntu Server 10.04 LTS system (kernel 2.6.32-22-server #33-Ubuntu SMP). Disk Subsystem is a software RAID5 array. The system has been set up for a little over a week. For the past 5 days I have been running at leat 3 VMs (Linux and a variety of Windows OSes) with no issues whatsoever. But while I was installing Linux onto a new VM, suddenly all VMs became unresponsive, including the one I was installing to. I could not log in to the VMWare Management Interface, and the system was somewhat unresponsive via SSH. When I looked at top, I saw: top - 16:14:51 up 6 days, 1:49, 8 users, load average: 24.29, 24.33 17.54 Tasks: 203 total, 7 running, 195 sleeping, 0 stopped, 1 zombie Cpu(s): 0.2%us, 25.6%sy, 0.0%ni, 74.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8056656k total, 5927580k used, 2129076k free, 20320k buffers Swap: 7811064k total, 240216k used, 7570848k free, 5045884k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 21549 root 39 19 0 0 0 Z 100 0.0 15:02.44 [vmware-vmx] <defunct> 2115 root 20 0 0 0 0 S 1 0.0 170:32.08 [vmware-rtc] 2231 root 21 1 1494m 126m 100m S 1 1.6 892:58.05 /usr/lib/vmware/bin/vmware-vmx -# product=2; 2280 jnet 20 0 19320 1164 800 R 0 0.0 30:04.55 top 12236 root 20 0 833m 41m 34m S 0 0.5 88:34.24 /usr/lib/vmware/bin/vmware-vmx -# product=2; 1 root 20 0 23704 1476 920 S 0 0.0 0:00.80 /sbin/init 2 root 20 0 0 0 0 S 0 0.0 0:00.01 [kthreadd] 3 root RT 0 0 0 0 S 0 0.0 0:00.00 [migration/0] 4 root 20 0 0 0 0 S 0 0.0 0:00.84 [ksoftirqd/0] 5 root RT 0 0 0 0 S 0 0.0 0:00.00 [watchdog/0] 6 root RT 0 0 0 0 S 0 0.0 0:00.00 [migration/1] The VMWare process for the virtual machine I was installing into became a zombie. Yet, it was still consuming 100% of the CPU time on one of the cores, and I couldn't reach it or any other virtual machines. (I was logged in to one virtual machine over SSH, another via X11, and a third via VNC. All three connections died). When I ran ps -ef and similar commands, I found that the defunct vmware-vmx process had it's parent PID set to init (1). I also used lsof -p 21549 and found that the defunct process had no open files. Yet it was using 100% of CPU time... I was unable to kill any vmware-vmx processes, including the defunct one, even with kill -9. As a last resort to resolve the situation I tried to reboot the box, however shutdown, halt, reboot, and init 6 all failed to reboot/shutdown, even when given appropriate --force settings. ControlAltDel produced a message about rebooting on the console, but the system would not reboot. I had to hard power-cycle the box to resolve the situation. (See my other question, Should I worry about the integrity of my linux software RAID5 after a crash or kernel panic?) What would cause a scenario like this? What else could I have done to resolve it besides a hard reboot? What can I do to prevent such a situation in the future?

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• Just a few questions about Hyper-V virtual machines and clustering

  - by René Kåbis

  I have been using Microsoft’s Hyper-V technology for a little while now, but I am just now dipping my toe into clustering. In particular, I am trying to implement a fault-tolerant SQL DB. This involves setting up two VMs, clustering them via Failover Cluster, and then installing SQL Server in some fashion. I have two physical machines - one high-end and rather beefy “heavy lifter” to contain the majority of the VMs, and another “backup” (a repurposed desktop) to hold the essential “secondary” (or failover) AD-DC, SQL and FS VMs. The main reason why I find the failover cluster at the VM level so attractive is that it presents a single IP and DNS entry to the network as a whole - if one machine (physical or virtual) goes down, you might loose some ping and the connections get reset, but the network applications (Microsoft RMS connection to backend SQL) can still connect to a viable DB without having to mess around with the settings at all. My first question is in terms of SQL Server itself. If I have a cluster between two VMs, does it make more sense to install the SQL Server in Failover Cluster configuration or should I simply install it in a stand-alone config and mirror the DBs? For example, this post suggests just mirroring the DBs, but do I just mirror standalone DBs on standalone VMs, or can I get the network and failover benefits of clustered VMs while still utilizing (on each clustered VM) standalone DBs that have been mirrored between each other? As well, I have come across a lot of documentation about SQL clustering, but most assume a number (#2) of physical machines to hold not only the actual SQL VMs but also the Quorum and Witness stores. I will not be able to muster more than two physical machines. As such, I will have to be satisfied with a VM cluster that does not exceed two VMs (one for each physical machine). Another issue involves MSDTC - the Distributed Transaction Coordinator. When attempting to install the SQL Failover Cluster (I never completed it for this reason) it threw a hissy fit because MSDTC had not been clustered. Search as I might, I have not yet found a way to do so under Windows Server 2012 R2. I have found plenty of docs for Windows 2008 and 2008 R2, but these instructions don’t align with 2012 R2 (at least, not in a way that allows me to successfully cluster MSDTC). Plus, some of the instructions that I have found for SQL Server Failover Cluster installation suggest that a third “network device” - shared network storage (a SAN) - is required for the DB itself (and other functionality). I do not have this, and won’t be getting this. Most of my storage exists on the “heavy lifter” that was designed for all of the “primary” VMs. If that physical machine goes down, so does the storage. The secondary server does have enough resources for an AD-DC Server, an SQL server and a File Server, so it will handle the “secondary” failover versions of those VMs (clustered or not). My final question involves file servers. If I cluster file servers between two VMs (one on my “heavy lifter” and another on my “backup”, how do I mirror the data between them? Clustering VMs only provides a single point of access on the network for a resource, it doesn’t exactly replicate data between the two - that is left to the services that serve up that data. I am unsure how I can ensure that file server data between two clustered file server VMs can be properly mirrored. Remember, I only have two devices to be used here - my primary machine and a backup secondary. There is no chance of me obtaining a SAN or any other type of network attached storage. What exists on the machines must act as the storage. Thanks in advance for any suggestions.

  Read the article

• Too many Bind query (cache) denied, DNS attack?

  - by Jake

  Once Bind crashed and I did: tail -f /var/log/messages I see a massive number of logs every second. Is this a DNS attack? or is there something wrong? Sometimes I see a domain in logs like this: dOmAin.com (upper and lower). As you see there is only one single domain in the logs with different IPs Oct 10 02:21:26 mail named[20831]: client 74.125.189.18#38921: query (cache) 'ns1.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.144.171#38833: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.17#42428: query (cache) 'ns2.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.27#37899: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 193.203.82.66#39263: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.170#59723: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 80.169.197.66#32903: query (cache) 'dOmAin.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 134.58.60.1#47558: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.34#47387: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.8#59392: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.19#64395: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 217.72.163.3#42190: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 83.146.21.252#22020: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.116#57342: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 193.203.82.66#52020: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.72#64317: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 80.169.197.66#31989: query (cache) 'dOmAin.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.18#47436: query (cache) 'ns2.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.16#44005: query (cache) 'ns1.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 85.132.31.10#50379: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 94.241.128.3#60106: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 85.132.31.10#59118: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 212.95.135.78#27811: query (cache) 'domain.com/A/IN' denied /etc/resolv.conf ; generated by /sbin/dhclient-script nameserver 4.2.2.4 nameserver 8.8.4.4 Bind config: // generated by named-bootconf.pl options { directory "/var/named"; /* * If there is a firewall between you and nameservers you want * to talk to, you might need to uncomment the query-source * directive below. Previous versions of BIND always asked * questions using port 53, but BIND 8.1 uses an unprivileged * port by default. */ // query-source address * port 53; allow-transfer { none; }; allow-recursion { localnets; }; //listen-on-v6 { any; }; notify no; }; // // a caching only nameserver config // controls { inet 127.0.0.1 allow { localhost; } keys { rndckey; }; }; zone "." IN { type hint; file "named.ca"; }; zone "localhost" IN { type master; file "localhost.zone"; allow-update { none; }; }; zone "0.0.127.in-addr.arpa" IN { type master; file "named.local"; allow-update { none; }; };

  Read the article

• What is the best server or Ip address to use for prolonged testing?

  - by eldorel

  I usually run uptime/latency tests against (and from) two servers that we own at different sites and until recently I've used the google dns servers as a control group. However, I've realized there is a potential problem with monitoring latency over extended periods of time. Almost all of the major service providers are using ANYCAST. For short tests this doesn't matter, but I need to run a set of tests for at least a week to try and catch an intermittent problem, and a change in the anycast priority while trying to test latency will cause the latency values for that server to change accordingly. Since I'm submitting graphs of this data to the ISP, I need to avoid/account for as many variables as possible. Spikes in the data for only one of the tested servers will only cause headaches. So can anyone recommend servers that: are not using anycast are owned by an entity that has a good uptime reputation (so they can't claim that the problem is server-side) will respond to ICMP requests Have an available service that runs on TCP/UDP (http or dns preferably) Wont consider an automated request every 10 minutes to be abuse Are accessible from anywhere in the world Are not local to the isp ( consider this an investigation of a hostile party ) Thanks in advance. Edit: added #6 and #7 above. More info: I am attempting to demonstrate a network problem for an entire node of our local ISP's network. They are actively blaming the issue on the equipment installed at the customer sites (our backup site is one of these), and refuse to escalate the problem. (even though 2 of these businesses have ISP provided modems, and all of us have completely different routers/services running) I am already quite familiar with the need to test an isp controlled IP, but they are actively dropping all packets targeted at gateway ip addresses and are only passing traffic addressed beyond the gateways. So to demonstrate the issue, I am sending packets to other systems in the same node, systems one hop away from the affected node, and systems completely outside the network. Unfortunately, all of the systems I have currently are either administered directly by myself, or by people who are biased enough to assist me. I need to have several systems included in the trace/log/graphs that are 100% not in the control of either myself or the isp so that the graphs have a stable/unbiased control group. These requirements are straight from legal, I'm just trying to make sure that everything that could be argued to invalidate the data is already covered. In Summary: I need to be able to show tcp/udp/icmp as 3 separate data points, and I need to be able to show the connections inside the local node, from local node to another nearby node, from those 2 nodes to the internet, and through the internet to both verifiable servers and a control group that I have no control over whatsoever. Again, Google/opendns/yahoo/msn/facebook/etc all use anycast, which throws the numbers off every time the anycast caches expire, so I need suggestions of an IP or server that is available for this type of testing. I was hoping someone knew of a system run by someone such as ISC or ICANN, or perhaps even a .gov server (fcc or nsa maybe?) setup for this type of testing. Thanks again.

  Read the article

• What seems to be plaguing my hard drives?

  - by Craig

  In a little bit of a tech nightmare here. I know oodles about software, not so much more than the above average user about hardware. I recently had to toss an old desktop of mine. It was gradually getting slower and slower, and after shutting the desktop down for long periods of time, it would choke up upon startup. Sometimes it'd give a disk read error, sometimes say no OS was found, etc. Restarting it about 5-15 times would eventually boot properly. Weird. I also noticed that startup programs were going missing, Dropbox was reindexing my entire folder, and Backblaze was backing up less than the number of files that it should. This lead me to believe it was probably a hard drive issue. I began to wonder why I'd have hard drive issues, and came to closure when I assumed it was because of recent power surges and outages. I'm sure that does a number on the drive. I bought a new desktop recently. It's not a beast or anything, but it's enough for what I do. It's an eMachines (I know, I know) Ultra-Slim (http://www.amazon.com/eMachines-Ultra-Slim-ER1401-57-Desktop-PC/dp/B00475OG9U). This is ideal for me because it's small and portable. It comes with an AC adapter and battery, like a laptop. Just to be safe, I bought an uninterruptable power supply on top of that. It's basically protected completely from any outages that might scramble the drive. I set this up a few days ago and for the past few days I've been perfecting settings, downloading the usual applications, etc. Two days ago, I noticed Dropbox was reindexing my entire Dropbox folder. I installed both Dropbox and Backblaze on this system, but it is very much more lightweight than the other. Only about 15 third-party applications installed. I thought that maybe Dropbox and Backblaze were stressing my system, so I turned off Backblaze. Still, Dropbox runs and comes across this infinite reindex issue. I noticed that upon a reboot recently, two applications did not start on startup either. Also, much like my old desktop, every 3rd or 4th reboot, I'll be forced into a chkdsk. This makes me incredibly nervous. What could possibly be going wrong with my old, years-old desktop that is immediately causing the same issues to my new one? I've considered all of the basics. I'm in a very air conditioned room. I take run routine virus scans. I'd like to think I take care of my systems very well. What is this issue that is haunting me? There's always the possibility that this new desktop has a junk hard drive, but it just seems way too coincidental.

  Read the article

• AMD Catalyst 13.9 installation failure

  - by Simon Verbeke

  Earlier today I installed Windows 8.1, and when I wanted to go into Catalyst Control Center, I noticed some odd error of CCC not being able to display options. I then figured I needed a driver update, so I downloaded the latest drivers, version 13.9, and tried to install them. While it was trying to install the display drivers, I got a blue screen. Tried again and got the same. Then I used an uninstall tool from AMD to remove all traces of my old drivers and tried to install the new drivers. Again, a blue screen. This is all I could think of to try. Would anyone know some other things I can try? EDIT: thought I might want to include the log entry for the crash: - <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> - <System> <Provider Name="Microsoft-Windows-WER-SystemErrorReporting" Guid="{ABCE23E7-DE45-4366-8631-84FA6C525952}" EventSourceName="BugCheck" /> <EventID Qualifiers="16384">1001</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2013-10-19T20:59:25.000000000Z" /> <EventRecordID>26587</EventRecordID> <Correlation /> <Execution ProcessID="0" ThreadID="0" /> <Channel>System</Channel> <Computer>Simon-PC</Computer> <Security /> </System> - <EventData> <Data Name="param1">0x0000007e (0xffffffffc0000005, 0xfffff80002a86dca, 0xffffd00025f250e8, 0xffffd00025f248f0)</Data> <Data Name="param2">C:\WINDOWS\MEMORY.DMP</Data> <Data Name="param3">101913-8953-01</Data> </EventData> </Event> Another edit: As it turns out, the graphics card isn't showing up any more in the device manager. But as far as I can tell, it is still working (the fans are spinning and my screen is plugged into that graphics card). This is solved. it appears that my graphics card is now running with a default windows driver. I also tried the forced method mentioned here: AMD Graphics Drivers won't install properly . But I still get a BSOD. Third edit: Slight succes! Managed to install version 13.4. Everything appears to be working fine now. I think I'm just going to skip version 13.9.

  Read the article

• amplified reflected attack on dns

  - by Mike Janson

  The term is new to me. So I have a few questions about it. I've heard it mostly happens with DNS servers? How do you protect against it? How do you know if your servers can be used as a victim? This is a configuration issue right? my named conf file include "/etc/rndc.key"; controls { inet 127.0.0.1 allow { localhost; } keys { "rndc-key"; }; }; options { /* make named use port 53 for the source of all queries, to allow * firewalls to block all ports except 53: */ // query-source port 53; /* We no longer enable this by default as the dns posion exploit has forced many providers to open up their firewalls a bit */ // Put files that named is allowed to write in the data/ directory: directory "/var/named"; // the default pid-file "/var/run/named/named.pid"; dump-file "data/cache_dump.db"; statistics-file "data/named_stats.txt"; /* memstatistics-file "data/named_mem_stats.txt"; */ allow-transfer {"none";}; }; logging { /* If you want to enable debugging, eg. using the 'rndc trace' command, * named will try to write the 'named.run' file in the $directory (/var/named"). * By default, SELinux policy does not allow named to modify the /var/named" directory, * so put the default debug log file in data/ : */ channel default_debug { file "data/named.run"; severity dynamic; }; }; view "localhost_resolver" { /* This view sets up named to be a localhost resolver ( caching only nameserver ). * If all you want is a caching-only nameserver, then you need only define this view: */ match-clients { 127.0.0.0/24; }; match-destinations { localhost; }; recursion yes; zone "." IN { type hint; file "/var/named/named.ca"; }; /* these are zones that contain definitions for all the localhost * names and addresses, as recommended in RFC1912 - these names should * ONLY be served to localhost clients: */ include "/var/named/named.rfc1912.zones"; }; view "internal" { /* This view will contain zones you want to serve only to "internal" clients that connect via your directly attached LAN interfaces - "localnets" . */ match-clients { localnets; }; match-destinations { localnets; }; recursion yes; zone "." IN { type hint; file "/var/named/named.ca"; }; // include "/var/named/named.rfc1912.zones"; // you should not serve your rfc1912 names to non-localhost clients. // These are your "authoritative" internal zones, and would probably // also be included in the "localhost_resolver" view above :

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• Distributed and/or Parallel SSIS processing

  - by Jeff

  Background: Our company hosts SaaS DSS applications, where clients provide us data Daily and/or Weekly, which we process & merge into their existing database. During business hours, load in the servers are pretty minimal as it's mostly users running simple pre-defined queries via the website, or running drill-through reports that mostly hit the SSAS OLAP cube. I manage the IT Operations Team, and so far this has presented an interesting "scaling" issue for us. For our daily-refreshed clients, the server is only "busy" for about 4-6 hrs at night. For our weekly-refresh clients, the server is only "busy" for maybe 8-10 hrs per week! We've done our best to use some simple methods of distributing the load by spreading the daily clients evenly among the servers such that we're not trying to process daily clients back-to-back over night. But long-term this scaling strategy creates two notable issues. First, it's going to consume a pretty immense amount of hardware that sits idle for large periods of time. Second, it takes significant Production Support over-head to basically "schedule" the ETL such that they don't over-lap, and move clients/schedules around if they out-grow the resources on a particular server or allocated time-slot. As the title would imply, one option we've tried is running multiple SSIS packages in parallel, but in most cases this has yielded VERY inconsistent results. The most common failures are DTExec, SQL, and SSAS fighting for physical memory and throwing out-of-memory errors, and ETLs running 3,4,5x longer than expected. So from my practical experience thus far, it seems like running multiple ETL packages on the same hardware isn't a good idea, but I can't be the first person that doesn't want to scale multiple ETLs around manual scheduling, and sequential processing. One option we've considered is virtualizing the servers, which obviously doesn't give you any additional resources, but moves the resource contention onto the hypervisor, which (from my experience) seems to manage simultaneous CPU/RAM/Disk I/O a little more gracefully than letting DTExec, SQL, and SSAS battle it out within Windows. Question to the forum: So my question to the forum is, are we missing something obvious here? Are there tools out there that can help manage running multiple SSIS packages on the same hardware? Would it be more "efficient" in terms of parallel execution if instead of running DTExec, SQL, and SSAS same machine (with every machine running that configuration), we run in pairs of three machines with SSIS running on one machine, SQL on another, and SSAS on a third? Obviously that would only make sense if we could process more than the three ETL we were able to process on the machine independently. Another option we've considered is completely re-architecting our SSIS package to have one "master" package for all clients that attempts to intelligently chose a server based off how "busy" it already is in terms of CPU/Memory/Disk utilization, but that would be a herculean effort, and seems like we're trying to reinvent something that you would think someone would sell (although I haven't had any luck finding it). So in summary, are we missing an obvious solution for this, and does anyone know if any tools (for free or for purchase, doesn't matter) that facilitate running multiple SSIS ETL packages in parallel and on multiple servers? (What I would call a "queue & node based" system, but that's not an official term). Ultimately VMWare's Distributed Resource Scheduler addresses this as you simply run a consistent number of clients per VM that you know will never conflict scheduleing-wise, then leave it up to VMWare to move the VMs around to balance out hardware usage. I'm definitely not against using VMWare to do this, but since we're a 100% Microsoft app stack, it seems like -someone- out there would have solved this problem at the application layer instead of the hypervisor layer by checking on resource utilization at the OS, SQL, SSAS levels. I'm open to ANY discussion on this, and remember no suggestion is too crazy or radical! :-) Right now, VMWare is the only option we've found to get away from "manually" balancing our resources, so any suggestions that leave us on a pure Microsoft stack would be great. Thanks guys, Jeff

  Read the article

• I am starting to think that Prevx.com isnt a legit site...but heres my long-winded question

  - by cop1152

  I apologize in advance for the long-winded post. I posted it all because I believe its informative and may be useful. Also, I posted my question at the end. Moments ago I was RDC to a file server in my home (from inside my home). I had opened Firefox and Googled for a manufacturers website. Immediately after clicking the link, Firefox abruptly closed. This seemed odd to me to so I checked the running processes and discovered d.exe, e.exe, and f.exe running. I Googled these processes on a different machine and found them belonging to a key-logger/screen-capturer/trojan called defender.exe, which according to the Prevx lives in c:\documents and settings\user\local settings\temp. (Prevx link http://www.prevx.com/filenames/147352809685142526-X1/DEFENDER32.EXE.html) Simultaneously, an obviously-spoofed Windows Firewall popup appeared on the server asking me to click ‘yes’ to update Windows Firewall. At this time I ended all rogue processes, emptied the temp folder, removed defender.exe from startup, and checked my registry and a few other locations. Before deleting Defender.exe I noted that it was created moments ago, just before Firefox crashed. I believe that I was ‘almost’ infected with this malware. I believe that it needed me to click the phony popup in order to complete infection because it wasn’t allowed to execute processes from the temp folder. After cleaning the machine, I restarted it and have been monitoring it for over an hour. I am debating on whether or not to restore the Windows partition (a separate physical drive from the data) or to just watch it for awhle. I should mention that, because of the specs on this machine, I do not run antivirus software, but I know it well and inspect it regularly. It is a very old Compaq with a 400mhz processer and 512mb of ram. I have a static IP and the server is in the DMZ running an FTP client and some HTTP server software. All files transferred to and stored on this machine are scanned for malware before transferring. Usually the machine only runs 19 processes and performs pretty well for its intended purpose. I posted the story so that you could be aware of a possible new piece of malware and how it acts, but I also have a question or two. First, over the last few months I have noticed that PREVX is listed at the top of most of my Google searches when researching malware, especially for new or obscure malware…and they always want you to purchase something. I don’t think they are one of the top AV companies, so it seems odd that they are always the top Google result. Does anyone have any experience with any of their products? Also, what sites do you rely on for malware researching? Recently, I have found it difficult to find good info because of HijackThis-logs and other deadend info cluttering up my searches. And lastly, besides antivirus, third-party firewall, etc, what settings would you use to lock down a machine to make it more secure in instances where a stubborn admin like myself refuses to run AV? Thanks.

  Read the article

< Previous Page | 460 461 462 463 464 465 466 467 468 469 470 471  | Next Page >