Search Results

Search found 15139 results on 606 pages for 'scripting interface'.

Page 486/606 | < Previous Page | 482 483 484 485 486 487 488 489 490 491 492 493  | Next Page >

• Can't ping through default gateway

  - by Andrew G.H.

  I have the following configuration: Routing table on M3 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.3.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 Routing table on M1 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 So basically M3's gateway is M1, and M1's gateway is M2's wireless internet interface. If I ping 8.8.8.8 from M1, everything is ok, replies are received. Pinging from M1 to M3 and viceversa is also possible. I have configured M1 as gateway trafic forwarder using firestarter package and stopped firewall with it. iptables policies are ACCEPT for everything. Problem: I have tried ping-ing ip 8.8.8.8 from M3 but without success. What could be the source of this problem?

  Read the article

• NTOP gives warnings on startup

  - by FR6

  I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

  Read the article

• IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing problem

  - by Ernest Mueller

  Hey all, I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

  Read the article

• Error while installing boost_1_54

  - by Farhat

  On trying to install boost I get this error during configuration checks. Googling did not give any pointers. [root@heracles boost_1_54_0]# ./b2 install Performing configuration checks - 32-bit : no (cached) - 64-bit : yes (cached) - arm : no (cached) - mips1 : no (cached) - power : no (cached) - sparc : no (cached) - x86 : yes (cached) error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - has_icu builds : no (cached) warning: Graph library does not contain MPI-based parallel components. note: to enable them, add "using mpi ;" to your user-config.jam - zlib : yes (cached) - iconv (libc) : yes (cached) - icu : no (cached) - icu (lib64) : no (cached) - compiler-supports-ssse3 : yes (cached) - compiler-supports-avx2 : no (cached) - gcc visibility : yes (cached) - long double support : yes (cached) warning: skipping optional Message Passing Interface (MPI) library. note: to enable MPI support, add "using mpi ;" to user-config.jam. note: to suppress this message, pass "--without-mpi" to bjam. note: otherwise, you can safely ignore this message. error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - zlib : yes (cached) How can the alternative for allocator sources be located? Thanks.

  Read the article

• TCP: Address already in use exception - possible causes for client port? NO PORT EXHAUSTION

  - by TomTom

  Hello, stupid problem. I get those from a client connecting to a server. Sadly, the setup is complicated making debugging complex - and we run out of options. The environment: *Client/Server system, both running on the same machine. The client is actually a service doing some database manipulation at specific times. * The cnonection comes from C# going through OleDb to an EasySoft JDBC driver to a custom written JDBC server that then hosts logic in C++. Yeah, compelx - but the third party supplier decided to expose the extension mechanisms for their server through a JDBC interface. Not a lot can be done here ;) The Symptom: At (ir)regular intervals we get a "Address already in use: connect" told from the JDBC driver. They seem to come from one particular service we run. Now, I did read all the stuff about port exhaustion. This is why we have a little tool running now that counts ports and their states every minute. Last time this happened, we had an astonishing 370 ports in use, with the count rising to about 900 AFTER the error. We aleady patched the registry (it is a windows machine) to allow more than the 5000 client ports standard, but even then, we are far far from that limit to start with. Which is why I am asking here. Ayneone an ide what ELSE could cause this? It is a Windows 2003 Server machine, 64 bit. The only other thing I can see that may cause it (but this functionality is supposedly disabled) is Symantec Endpoint Protection that is installed on the server - and being capable of actinc as a firewall, it could possibly intercept network traffic. I dont want to open a can of worms by pointing to Symantec prematurely (if pointing to Symantec can ever be seen as such). So, anyone an idea what else may be the cause? Thanks

  Read the article

• How to subnet hosted VMs

  - by bwizzy

  I have a network of VMs each having a LAN IP address and a public IP address. They each have a 1:1 NAT map for public access via the public IP for HTTP, SSH etc. I'm trying to figure out a way to restrict the LAN IPs from talking to each other, but there are some cases where a group of LAN IPs will need to communicate. I'm using pfSense as a firewall / router on a 192.168.0.0/24 configuration. It seems like I could assign each VM it's own subnet and add a static route to the firewall for that VM to get back to the firewall for internet access / other fw rules. Is that right? I assigned 1 VM with: address 192.168.1.2 netmask 255.255.255.254 gateway 192.168.1.1 Then added a static route on the FW's LAN interface using 192.168.1.0/30 as the destination network and 192.168.1.1 as the gateway. Nothing appears to be working, anyone have any ideas? Please be aware I'm not that familiar with subnets. Thanks!

  Read the article

• Change font size for "Default Paragraph Font" in Word

  - by Richard Gadsden

  I have a document where the built-in style "Default Paragraph Font" has been set to a particular size. It shouldn't have a size - it should be inheriting from the paragraph style (that's the whole point of the style). If I go through the user interface, I can't modify this style (the modify button / dropdown is greyed out) While I can work around this in most places, it creates problems for the Table of Contents in particular, as that is forced to be in this style and it overrides the font size from the styles like TOC 1 (etc). I can set the font size through VBA - ActiveDocument.Styles("Default Paragraph Font").Font.size = 10 sets it to ten point, but I can't work out how to reset it back to inherit. At the moment, my table of contents is set to be all in the same size, but really TOC 1 should be bigger than TOC 2. Does anyone have any suggestions for how to fix this? One approach is to use the organizer to copy over the style from a working document, but ideally I'd like a way to resolve the problem without doing that - especially as that's not an easy approach to automate.

  Read the article

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• What does a connection timeout indicate when performing an NFS mount?

  - by DeeDee

  We have a shiny new QNAP NAS (TS-879U-RP), and I'm trying to mount it to our big ol' RHEL server in the same manner as our other two QNAP NAS devices. The IT department won't give me the root privileges to the NAS, so I can't SSH in (I know, I know). The first thing I did was to, via the QNAP web admin interface, create a network share named "Runs." I then added the IP of the RHEL server to the permissions list: On the RHEL server, I then added the following line to /etc/fstab: [IP of NAS]:/Runs /mnt/gsrnas3 nfs defaults 0 0 Aside from the IP and the specific mount directory name, this is how I mounted the other two NAS devices. I then created the gsrnas3 directory under /mnt/, and then ran `mount /mnt/gsrnas3' I got the following error: mount.nfs: Connection timed out My first thought is that it's a ports issue, but I don't have enough specific experience with this issue to know for sure. I have two other NAS devices by the same manufacturer already mounted to this RHEL server, so that leads me to believe the configuration issue is on the NAS side of things. I can ping the NAS device successfully from the RHEL server. Not being able to SSH into said NAS is a huge hassle, though. Any ideas?

  Read the article

• Why does my DSDT table is different from what I found online?

  - by Hao Shen

  I have found a field in DSDT table where I want to modify from here http://www.ztex.de/misc/c2ctl.e.html Generally, I want to modify the _PSS field about the processor so that I can have more frequency levels available in the CPUfreq driver interface. I try to use this command to dissemble the DSDT table from my Desktop(Linux2.6.29,Intel CORE 2): cat /proc/acpi/dsdt > dsdt.aml iasl -d dsdt.aml Then I have a file dsdt.dsl as following(very long, so I just show the beginning of the file): /* * Intel ACPI Component Architecture * AML Disassembler version 20090123 * * Disassembly of dsdt.aml, Mon May 6 20:41:40 2013 * * * Original Table Header: * Signature "DSDT" * Length 0x00003794 (14228) * Revision 0x01 **** ACPI 1.0, no 64-bit math support * Checksum 0x46 * OEM ID "DELL" * OEM Table ID "dt_ex" * OEM Revision 0x00001000 (4096) * Compiler ID "INTL" * Compiler Version 0x20050624 (537200164) */ DefinitionBlock ("dsdt.aml", "DSDT", 1, "DELL", "dt_ex", 0x00001000) { Method (DBIN, 0, NotSerialized) { Noop } Scope (\) { Device (_SB.VBTN) ................... But I can not find the _PSS field as shown in the website I have given above. I do not know why? I am sure the current cpufreq driver shows 4 frequency levels available. So at least there should be something in the table showing this..right? Has anybody here played with the DSDT table before? Thanks,

  Read the article

• Tcpreplaying using VMware

  - by Methos

  This is more like a testbed setup question. I want to use VMware to debug some networking code in the linux kernel in the VM. My VM has two network interfaces. What I want to do is replay the capture file in the host and receive the packets in the VM. My problem is I do not see replayed packets in the VM. I am running VMware and tcpreplay on the host as sudo. Hence I think there should not be any problem access devices files. I am running VMware workstation 7.0 a. I first began with Custom networking as that provides option of creating your own virtual network name. I wrote /dev/vmnet3 and /dev/vmnet4 for the two interfaces respectively. However, after booting the guest, I did not see any of these interfaces or devices files (in /dev) created on the host. b. Then I tried 'Host Only', but that does not show what bridge/device file is associated with the interface. c. Finally I tried bridged networking mode. I see vmnet1, vmnet8 and vboxnet0 on the host. I have tcpreplayed the capture file on each of these interfaces, for all the above three cases. I tried to capture packets in the VM using "tcpdump -i any". However, I do not see any packets. Any ideas/pointers?

  Read the article

• (Zywall USG 300) NAT bypassed when accessing in-house-server From LAN Via domain name

  - by mschr

  My situations is like this; i host a number of websites from within our joint network solution. On the network is basically 3 categories: the known public, registered via mac, given static dhcp lease the anonymous lan connections, given lease from specific dhcp range switches, unix hosts firewall Now, consider following hosts which are of interest 111.111.111.111 (Zywall USG 300 WAN) 192.168.1.1 (ZyWall USG 300 LAN) load balances and bw monitors plus handles NAT 192.168.1.2 (Linux www) serves mydomain1.tld and mydomain2.tld 192.168.123.123 (Random LAN client) accesses mydomain1.tld from LAN 23.234.12.253 (Random External client) accesses mydomain1.tld via WAN DNS A records are setup so that both mydomain1.tld and mydomain2.tld points to 111.111.111.111 - and the Linux www serves the http parts with VirtualHost configurations, setting up the document roots pr ServerName, this is not so interesting though.. NAT rule translates 111.111.111.111:80 to 192.168.1.2:80 (1:1 NAT) Our problem follows; When accessing http://mydomain1.tld from outside (23.234.12.253 example host) the joint network - everything is fine, zywall receives requests via port 80 and maps it to the linux host' httpd. However - once trying to go through the NAT from LAN side (in-house, 192.168.123.123 example host) then one gets filtered in the Zywall port 80 firewall. I know this only because port 443 is open for administration interface and https://mydomain1.tld prompts for zywall login. So my conclusion is, that the LAN that accesses 111.111.111.111 in fact are routed to 192.168.1.1 whilst bypassing the NAT table. I need to know how to setup NAT / Policy Route, so that LAN WAN LAN will function with proper network translations instead of doing the 'quick nameserver lookup' or whatever this might be.

  Read the article

• Forwarding HTTP Request with Direct Server Return

  - by Daniel Crabtree

  I have servers spread across several data centers, each storing different files. I want users to be able to access the files on all servers through a single domain and have the individual servers return the files directly to the users. The following shows a simple example: 1) The user's browser requests http://www.example.com/files/file1.zip 2) Request goes to server A, based on the DNS A record for example.com. 3) Server A analyzes the request and works out that /files/file1.zip is stored on server B. 4) Server A forwards the request to server B. 5) Server B returns file1.zip directly to the user without going through server A. Note: steps 4 and 5 must be transparent to the user and cannot involve sending a redirect to the user as that would violate the requirement of a single domain. From my research, what I want to achieve is called "Direct Server Return" and it is a common setup for load balancing. It is also sometimes called a half reverse proxy. For step 4, it sounds like I need to do MAC Address Translation and then pass the request back onto the network and for servers outside the network of server A tunneling will be required. For step 5, I simply need to configure server B, as per the real servers in a load balancing setup. Namely, server B should have server A's IP address on the loopback interface and it should not answer any ARP requests for that IP address. My problem is how to actually achieve step 4? I have found plenty of hardware and software that can do this for simple load balancing at layer 4, but these solutions fall short and cannot handle the kind of custom routing I require. It seems like I will need to roll my own solution. Ideally, I would like to do the routing / forwarding at the web server level, i.e. in PHP or C# / ASP.net. However, I am open to doing it at a lower level such as Apache or IIS, or at an even lower level, i.e. a custom proxy service in front of everything. Thanks.

  Read the article

• Dell OpenManage On Ubuntu Server 12.04 Cannot Log In

  - by Austin

  I have a Dell Poweredge 2950 with 2X130GB and 2X2TB drives. I need to set them up in a RAID 1 array so that the 130GB Drives are mirrored and host the OS, while the 2TB drives are mirrored and are the content drives. So I go from 4 disks, down to two, one 130GB and one 2TB. I can do that in the BIOS RAID utility no problem. But I need to be able to manage the RAID arrays and be able to expand them WITHOUT shutting down the server. Now, to my understanding, openmanage will allow me to do that AND it runs on ubuntu. So I go and set it up and try to log into the web interface at and it will not let me log in. I have followed dell's guide to set up openmanage, even added the usernames to the files and permissions and such, however, cannot get it to let me log in or anything. I have reinstalled Openmanage several times, even reinstalled the OS three times, and nothing works. Google does not help either. It simply says login failed after hitting submit. Please Help

  Read the article

• Netgear GS724Tv3 and link aggregation Mac OS X Server 10.6.8

  - by Manca Weeks

  I need to link aggregate 2 sets of ports on the Netgear GS724T with my Apple server tower (latest generation). I have 2 built in ports and 2 ports on a PCIe ethernet card. It is not obvious to me how to properly configure the Netgear end. I have access to the Netgear box through its web interface, just don't know how to properly set the settings. I tried going to Netgear for help, but they said my software support has expired. I bought this unit on their recommendation - they say it is compatible with 802.3ad protocol. I cannot locate any references to this protocol in the manual and I noticed some people in formus say that this device is actually not compatible with 802.3ad and that Netgear is misleading potential customers by saying it is. Any help will be appreciated. Thanks, M My own answer - posted as edit because of restrictions on my user: OK folks, turns out one must use a Windows machine on this one or nothing makes sense. I was unable to get much farther than viewing the default inactive LAGs because in Firefox and Safari on Mac things don't make much sense - i.e. the Apply buttons (supposedly JavaScript) don't work. You can view the configurations, but none of the modifications you make stick. Then, in Switching - LAGs, choose the ports to include and make sure you switch the LAG type from Static to LACP and all is well. Haven't tested the performance of the config yet, but both sides appear to be happy with the configuration. Apple server says link active and so does the Netgear. Will report if any other discoveries. Thanks for all who read and to user84104 for responding. M

  Read the article

• iptables advanced routing

  - by Shamanu4

  I have a Centos server acting as a NAT in my network. This server has one external (later ext1) interface and three internal (later int1, int2 and int3). Egress traffic comes from users via int1 and after MASQUERADE goes via ext1. Ingress traffic comes from ext1, MASQUERADE, and goes via int2 or int3 according to static routes. | ext1 | x.x.x.x/24 +---------|----------------------+ | | | Centos server (NAT) | | | +---|------|---------------|-----+ | | | int1 | | int2 | int3 10.30.1.10/24 | | 10.30.2.10/24 | 10.30.3.10/24 ^ v v 10.30.1.1/24 | | 10.30.2.1/24 | 10.30.3.1/24 +---|------|---------------|-----+ | | | | | | | v v | | ^ -Traffic policer- | | |_____________ | | | | | +------------------|-------------+ | 192.168.0.1/16 | | Clients 192.168.0.0/16 The problem: Egress traffic seems to be dropped after PREROUTING table. Packet counters are not changing on MASQUERADE rule in POSTROUTING. If I change the routes to clients causing the traffic go back via int1 - everything works perfectly. current iptable configuration is very simple: # cat /etc/sysconfig/iptables *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -I INPUT 1 -i int1 -j ACCEPT -A FORWARD -j ACCEPT COMMIT *nat -A POSTROUTING -o ext1 -j MASQUERADE # COMMIT Can anyone point me what I'm missing? Thanks. UPDATE: 192.168.100.60 via 10.30.2.1 dev int2 proto zebra # routes to clients ... 192.168.100.61 via 10.30.3.1 dev int3 proto zebra # ... I have a lot of them x.x.x.0/24 dev ext1 proto kernel scope link src x.x.x.x 10.30.1.0/24 dev int1 proto kernel scope link src 10.30.1.10 10.30.2.0/24 dev int2 proto kernel scope link src 10.30.2.10 10.30.3.0/24 dev int3 proto kernel scope link src 10.30.3.10 169.254.0.0/16 dev ext1 scope link metric 1003 169.254.0.0/16 dev int1 scope link metric 1004 169.254.0.0/16 dev int2 scope link metric 1005 169.254.0.0/16 dev int3 scope link metric 1006 blackhole 192.168.0.0/16 default via x.x.x.y dev ext1 Clients have 192.168.0.1 as gateway, which is redirecting them to 10.30.1.1

  Read the article

• HUDSON: how to manually encode the LDAP managerPassword?

  - by user64204

  I need to know how to manually encode the LDAP managerPassword which controls the authentication to hudson: <securityRealm class="hudson.security.LDAPSecurityRealm"> <server>ldap.example.org</server> <rootDN>dc=example,dc=org</rootDN> <userSearchBase>ou=People</userSearchBase> <userSearch>uid={0}</userSearch> <groupSearchBase>ou=Groups</groupSearchBase> <managerDN>cn=admin,dc=example,dc=org</managerDN> <managerPassword>{HOW DO I ENCODE THIS?}</managerPassword> </securityRealm> This question has already been raised here: http://jenkins.361315.n4.nabble.com/How-to-encode-the-LDAP-managerPassword-td2295570.html The answer was to configure the managerPassword field via the hudson web interface. The problem we have is that in order to configure LDAP one must be authenticated to hudson, which we cannot do because our LDAP authentication is currently broken (password mismatch between LDAP and the hudson configuration). Can someone explain how to manually encode the LDAP managerPassword? Thanks

  Read the article

• Change OpenVZ route to pass through ip failover

  - by Kevin Campion

  I have one dedicaced server with its own IP and another IP (failover) who refer to the first. I will wish to change the gateway of a Proxmox virtual machine (openvz) who runs on this dedicaced server to go through the failover IP rather than the ip of host main server. Once connected to a virtual machine, when I do a traceroute VE# traceroute www.google.fr traceroute to www.google.fr (209.85.229.104), 30 hops max, 60 byte packets 1 MY_SERVER_NAME.ovh.net (xxx.xxx.xxx.xxx FIRST_IP_MAIN_SERVER) 0.021 ms 0.010 ms 0.009 ms The first line tells me the ip of host main server. I would like that the traceroute display the second IP failover. VE# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 * 255.255.255.255 UH 0 0 0 venet0 default 192.0.2.1 0.0.0.0 UG 0 0 0 venet0 With iptables HOST# iptables -t nat -L Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- anywhere anywhere MASQUERADE all -- anywhere anywhere SNAT tcp -- anywhere 10.10.101.2 tcp dpt:www state NEW,RELATED,ESTABLISHED,UNTRACKED to:SECOND_IP_FAILOVER SNAT all -- 10.10.101.2 anywhere to:SECOND_IP_FAILOVER 10.10.101.2 is the virtual machine IP (interface venet0) Any ideas ?

  Read the article

• How to configure networking on an appliance such that it can plug and play on any corporate network?

  - by Joshua Lim

  I had a chance to configure a Moxa NPort device server appliance on my client's network, it was very easy to do so, done in just 2 minutes. Here's what I did:- The Moxa device server had a preset IP address of 192.168.127.254 and subnet mask 255.255.255.0 - http://www.moxa.com/doc/manual/nport/5400/NPort_5400_Series_Users_Manual_v4.pdf Moxa provides a Windows software which I used to "scan" for the device server. It worked like magic! The software returns a list of device servers found. Each device server is identified by MAC address, and by selecting the device server using the software, I can reset the default IP address and subnet mask of that device server! In comparison, during an earlier project, I spent 2 hours trying to get KVM to work for a Windows 7 embedded appliance I'm trying to install in my client's network - http://superuser.com/questions/380305/how-to-configure-windows-7-professional-appliance-pc-on-my-clients-network-usin Prior to that, I have already tried pre-configuring the IP address and subnet mask to the one which my client provided, yet the appliance still can't connect to the client's network! I've also tried cross cable, didn't work either. After KVM worked, I discovered that the network settings were "lost" after I plug the machine into the client's network. Now my question is what can I do to setup my Windows 7 embedded appliance so that it can connect to any network like that the Moxa device server? I tried experimenting this on my network using a Windows machine configured to an IP address of 192.168.127.254 and subnet mask 255.255.255.0, but it doesn't connect to my network that uses 192.168.0.*. :( EDIT: I would like to point out that the Moxa Windows configuration software seems to be able to connect to any Moxa device connected to the network even if it is on a different subnet, as long as the network adapter shows "connected". This is important because the Moxa device has no VGSM port or interface to configure the IP address.

  Read the article

• Reliable applicance for routing IT emergency calls (SIP and ISDN)

  - by chiborg

  We have a fairly big IT installation and our IT staff needs to be reachable 24/7. At the moment we have the following setup for "emergency" calls to our IT staff on our main Asterisk box: An incoming emergency number (connected via SIP trunk and a BRI card in case the SIP trunk goes down). When the number is called during the office hours, all the SIP phones of the IT staff are called simultaneously. When the number is called out of office hours interface, a list of mobile phone numbers is called, one after another until someone picks up. The list can be changed by the IT staff via command line script. The setup works well, but the Asterisk is heavily used in a call center, has experienced some outages and misconfigurations, each of them bringing down the IT emergency number. So we'd like to put the IT emergency call functionality on a separate device. This does not need to be a big server, it even does not need to be Asterisk, it only has one purpose and should do it reliably. It should be very low-maintenance. Any suggestions for hard- and software?

  Read the article

• Using modem for sending voice recording

  - by ircmaxell

  I've got an interesting one for you. I've been going over my server monitoring and notification systems (Nagios based), and realized that if our internet connection goes down, there's no way for it to notify me. I already have a modem listening (Via CentOS 5) on a spare POTS line so that I can dial-in in case our internet goes down. I was wondering if I could come up with a script (Shell, Python, etc) that can dial out and play a recorded message (wave file I'm guessing) when it's picked up. I know Windows supports voice calls over a voice modem, I was wondering if a solution existed for Linux... I know asterisk can probably do it, but isn't that overkill (A full blown VOIP system just for a notification mechanism that will hopefully never be used)? And wouldn't it interfere with the modem's primary function as a backup network interface (PPP spawned via mgetty)? I've done some searching, and haven't really come up with much. I know how to dial out from the command line, but only as a modem (not as voice). Worst case, I could set it up to dial out as a modem, and then just realize that if I get a call with modem sounds from that number that it's the notification... Any insight would be appreciated...

  Read the article

• Valid IP address but can't surf without rebooting

  - by Kat

  I periodically lose internet and router connection at home. When this happens, others are using the router just fine. I am connecting directly through a wired connection to a Belkin router. I can release and renew the IP (and the IP addresses change to 0.0.0.0 and to an IP in my router's range beginning with 192.168.2. as they should) but still can't surf, can't access the router interface. Cycling the router doesn't help, and again, others are able to access the router fine at this time. Only rebooting the computer resolves the issue, and everything is wonderful for a few hours- and then I lose connection again. I have several ideas where to go from here, but I'd like to get some advice first. (Using Windows XP SP3, hardwired connection) Update As stated in the originally, releasing and renewing doesn't solve the issue. However, I have an update. I can ping localhost and my router IP with no problem at all when the issue occurs. However, repairing the network connection does not help. I AM able to get back on by disabling and then re-enabling the network connection in XP. What does that tell us?

  Read the article

• RDP or SSH connection trough Windows 2008 server VPN hang after a while

  - by xt4fs

  I have been experiencing a very strange issue with our VPN setup on Windows Server 2008. That server is running as a Xen Virtual Machine. We use it for two purposes, permit our mobile workers to connect to another server hosted somewhere else that only allow that ip, and use it to RDP or ssh to many other virtual machine on the same server. The server has no performance issue and still a load of memory free. All other virtual machine has no problem whatsoever. Many of those virtual machine have public IP (web servers) and all their firewall are set to allow only ssh connection or RDP connection from their local interface. When I am connecting directly with either ssh or RDP to one of the other virtual machine everything run without any issues. However, when I am doing so through the VPN after some time the connection just hang, it usually continue after some time (5 or 10 minutes). It seems as more there is network usage more often it happen to a point where it is completely unusable. The worst thing I can do to hang it faster is to actually ping the vpn client IP from the local network, after some time the latency increase until it hang. This happen even if I do RDP to the local ip of the VPN server trough the VPN. The server report no problem and if I disconnect to the vpn and reconnect right away everything is alright. There is nothing wrong in the VPN server log. I have taught at the beginning that it could have been an issue with the Host server so I try to RDP,ssh directly to the guest and I have experience no issue while doing this, so it really seems to be a problem with the VPN server on Windows server 2008. Another very weird thing is it does not seems to be of any issue if you only do Internet (NAT) without trying to connect to any local ips.

  Read the article

• server and user directly connected no pinging...

  - by jtzero

  I have a server(fedora 12) with two nics on it, directly connected to say 192.168.1.0 and 192.168.2.0 the route table looks like this Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 192.168.1.1 255.255.255.0 U 0 0 0 eth0 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 eth0 = 192.168.1.15 eth1 = 192.168.2.1 and a directly connected user (Mythdora) on the 192.168.2.0 network with ip 192.168.2.2 and route table like so Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 0 0 0 eth0 the cable is a crossover and it works all three nics work -- connected my laptop to either end and assign it a valid 192.168.2.0 ip the pings will work. In fact if I disconnect the server side and plug the eth cable into the laptop and have thte box ping the laptop continually remove the eth cable and plug it back into the server both sides ping... unfortunately the box realizing it's connected to a different pc wipes its route table after say ten minutes or so. if I do a trace route from a box on the 1.0 network to the servers 192.168.2.1 interface never get a reply from it. as a note at one point I could ping the server from the 192.168.2.2 box but the server couldnt ping the 192.168.2.2 box.

  Read the article

• SLI Video Cards

  - by Scott

  I'm configuring a new desktop. I'm looking through all PCI Express 2.0 x16 video cards on NewEgg at the moment. All cards seem to be stating that they have SLI Support or CrossFireX support. I know that these 2 technologies enable you to connect more than one video card together to create more of a powerful video experience. These cards that have this support seem to be more expensive that other cards though. When I did a NewEgg search for cards that did NOT have these two supports, no matches came up for PCI Express 2.0 x16 (haven't checked other interfaces yet though). Can you run an SLI/CrossFireX card as a single card (and if you can is it efficient or even good?), or do you need to have more than one card to run them? Also, do they make cards without these two technologies anymore, and are they even cheaper at this point? I really have no need for SLI/CrossFireX at all, so I was wondering what I should look into. Do cards without this technology not run on the PCI Express 2.0 x16 interface? Thanks ahead of time for all your help.

  Read the article

< Previous Page | 482 483 484 485 486 487 488 489 490 491 492 493  | Next Page >