Search Results

Search found 14544 results on 582 pages for 'ssh config'.

Page 489/582 | < Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >

• Join Domain from VM

  - by Adis

  I have two VMs running on VMWare Player. I use NAT adapter settings. The host machine for VMs is running on corporate network. First VM has Domain controller running and I can log in on that machine using domain credentials. I named domain wm.local When I run IP config on this machine: IP: 192.168.87.132 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 Second VM cannot join domain. When I try it with domain WM I'm propmted for credentials. And I enter Administrator credentials and than it waits for some time and I get response: "The specified domain either does not exist or could not be contacted" If i type wm.local as domain when trying to join it does not prompt me to login but just shows "An Active Directory Domain Controller (AD DC) for the domain wm.local could not be contacted. And here it takes no time to get this error message. Ipconfig on this machine: IP: 192.168.87.134 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 I can ping second VM from first one. And I disabled firewalls on both machines. Any ideas? Is there any manual for this?

  Read the article

• Can't access certain web sites - reset router, any ideas?

  - by IniTech

  EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

  Read the article

• PassEnv does not find ENV variables

  - by quodlibetor

  I've got this /etc/profile.d/myfile.sh: export MYVAR=myval I also have a PassEnv MYVAR line in a <virtualhost> section of an apache conf dir. That lets me do things like: $ echo $MYVAR myval $ python >>> import os; os.getenv('MYVAR') 'myval' $ sudo echo $MYVAR myval $ sudo -i root# echo $MYVAR myval But then, despite that being the case I get: root# /sbin/service httpd restart /sbin/service httpd restart Stopping httpd: [ OK ] Starting httpd: [Mon Oct 22 14:44:02 2012] [warn] PassEnv variable MYVAR was undefined [ OK ] And all of my attempts to access MYVAR from within my wsgi scripts just don't work. Thoughts? Am I doing something obviously wrong? EDIT for more detail I've got a swarm of computers/VMs and a swarm of developers working on a swarm of projects. I need a simple central place to keep environment information, the most common is the "environment" (dev/stage/prod). The scheme that we've got (modifying *.wsgi programmatically) is turning out to be more fragile than we'd like. The main options that I see are: put things in the shell environment put things in other config files Getting things into the shell environment is the best, because we won't need to write yet more duplicated "what is my environment" code.

  Read the article

• Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

  - by Brandon Bearden

  Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

  Read the article

• sub application and virtual directory file permissions

  - by Zeus

  I have a website setup in IIS7, exampledomain.com. Under the application exampledomain.com lives a sub application cms. In a rather convoluted way, we have content in our cms system in this sub-app, under cms\content\{generatedfoldername}. So to access an image in this content, the full URL would be http://www.exampledomain.com/cms/cms/content/{generatedfoldername}/image.jpg, (yes, cms twice...) and this works just fine. Now, we have a virtual directory under the parent website, called stuff which points at the content of the cms. So I should be able to get to the image using the url http://www.exampledomain.com/stuff/{generatedfoldername}/image.jpg. Unfortunately this gives a server 500 error "There is a problem with the resource you are looking for, and it cannot be displayed." Whilst you do have to log into the cms system to access any of the admin pages within, I don't think the image files are protected by login, or else the first example URL wouldn't work, right? Also it's a server 500 error, rather than a 403. I'm sure I must be missing something obvious here- will the virtual directory be using the permissions defined in the parent application, or the subapplication to which it is pointing? Or is there some other permissions I may have missed? Sorry, that was a bit long, thanks for reading all the way down here! (I also must point out that I'm pretty new to the server management stuff.) edit: also, we have <location path="." inheritInChildApplications="false"> specified in the webconfig of the parent app, so it's hopefully not the issue described in this config file hierarchy article.

  Read the article

• D-Link wireless router losing outbound data

  - by gsteinert

  I have a Linux box running the Apache web server behind a D-Link wireless router (nothing fancy, just standard kit that comes with Virgin Media broadband). My issue is that when requesting web pages (from within the network or via the web), the back end of the page seems to be being dropped. For example, I tried to display a text-only file, and all I could get was the first 40-70% of the file (it changed slightly with each refresh). The apache access logs show that only part of the data was being sent (~6000 bytes instead of the 12000+ bytes of the file). Removing my router from the equation fixes the issue and I can download any files no matter the size with no problems. My theory is that the uploaded packets are either being dropped or held up by the config of the router. Is there anything I can do to alleviate the problem? (Perhaps a way of reconfiguring the router to upload packets harder/better/faster/stronger or an option in apache that provides a workaround) As a last resort I will get a second NIC for my Linux box and turn it into a router, but that would mean the box will be on 24/7... not the most ideal of circumstances. Gary

  Read the article

• Empty $upstream_http_location variable if response was cached

  - by Ivaldi

  I would like to cache the response of an redirect. (Cache the request to some site which returns a redirect and cache the second request which returns the actual content.) So far my config looks like this: location = /proxy { error_page 301 302 307 = @redir; resolver 8.8.8.8; proxy_pass $arg_url; proxy_intercept_errors on; proxy_cache pcache; proxy_cache_key $arg_url; proxy_cache_valid 200 301 302 307 1d; proxy_cache_min_uses 1; proxy_ignore_client_abort on; proxy_ignore_headers Set-Cookie Expires Cache-Control; } location @redir { resolver 8.8.8.8; # we need to assign $upstream_http_location to another var in order to use it with proxy_pass set $target $upstream_http_location; proxy_pass $target; proxy_cache predirects; proxy_cache_key $upstream_http_location; proxy_cache_valid 200 301 302 307 1d; proxy_cache_min_uses 1; proxy_ignore_headers Set-Cookie Expires Cache-Control; } It works for the first request or without the 30x codes for proxy_cache_valid in the /proxy part, but $target and $upstream_http_location are empty, if the response was cached. Is there a nice solution to cache both requests? Thanks!

  Read the article

• Scaling a node.js application, nginx as a base server, but varnish or redis for caching?

  - by AntelopeSalad

  I'm not close to being well versed in using nginx or varnish but this is my setup at the moment. I have a node.js server running which is serving either json, html templates, or socket.io events. Then I have nginx running in front of node which is serving all static content (css, js, etc.). At this point I would like to cache both static content and dynamic content to memory. It's to my understanding that varnish can cache static content quite well and it wouldn't require touching my application code. I also think it's capable of caching dynamic content too but there cannot be any cookie headers? I do use redis at the moment for holding session data and planned to use it for other things in the future like keeping track of non-crucial but fun stats. I just have no idea how I should handle caching everything on the site. I think it comes down to these options but there might be more: Throw varnish in front of nginx and let varnish cache static pages, no app code changes. Redis would cache dynamic db calls which would require modifying my app code. Ignore using varnish completely and let redis handle caching everything, then use one of the nginx-redis modules. I'm not sure if this would require a lot of app code changes (for the static files). I'm not having any luck finding benchmarks that compare nginx+varnish vs nginx+redis and I'm too inexperienced to bench it myself (high chances of my configs being awful). I'm basically looking for the solution that would be the most efficient in terms of req/sec and scalable in the future (throw new hardware at the problem + maybe adjust some values in a config = new servers up and running semi-painlessly).

  Read the article

• Why is there an extra HDD under /dev being added in my Linux Kernel?

  - by user1279156

  I have created a Linux kernel and for some reason an extra drive is always added at bootup. My hard drive is listed as /dev/sdb. /dev/sda is created too, and it is 8 MB in size. I can't find anything in the kernel config that is creating this, but if I use a different kernel it is not there. Kernel logs show it as an attached SCSI device, looks just like my hard drive but only 8 MB, and has no partition table. It also doesn't appear to be a physical device. I've tried the kernel on many different models of PCs and it is always there. Does anyone know how to remove it? /dev/disk/by-id gives me: scsi-1AMCC_U21413034D98EB000584 scsi-1AMCC_U21413034D98EB000584-part1 scsi-353333330000007d0 scsi-SATA_ST3250312AS_5VY7SH42 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675-part1 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675-part2 hdparm -i /dev/sda gives me an "invalid argument". dd if=/dev/sda of=sda.img the resulting file does not have any content sdparm results: /dev/sda: Linux scsi_debug 0004 Device identification VPD page: Addressed logical unit: designator type: T10 vendor identification, code set: ASCII vendor id: Linux vendor specific: scsi_debug 2000 designator type: NAA, code set: Binary 0x53333330000007d0 Target port: designator type: Relative target port, code set: Binary transport: Serial Attached SCSI (SAS) Relative target port: 0x1 designator type: NAA, code set: Binary transport: Serial Attached SCSI (SAS) 0x52222220000007ce designator type: Target port group, code set: Binary transport: Serial Attached SCSI (SAS) Target port group: 0x100 Target device that contains addressed lu: designator type: NAA, code set: Binary transport: Serial Attached SCSI (SAS) 0x52222220000007cd designator type: SCSI name string, code set: UTF-8 transport: Serial Attached SCSI (SAS) SCSI name string: naa.52222220000007CD

  Read the article

• MySQL Tables Missing/Corrupt After Recreation

  - by Synetech inc.

  Hi, Yesterday I dumped my MySQL databases to an SQL file and renamed the ibdata1 file. I then recreated it and imported the SQL file and moved the new ibdata1 file to my MySQL data directory, deleting the old one. I’ve done it before without issue, however this time something is not right. When I examine the (personal, not MySQL config) databases, they are all there, but they are empty… sort of. The data directory still has the .ibd files with the correct content in them and I can view the table list in the databases, but not the tables themselves. (I have file-per-table enabled, and am using InnoDB as default for everything.) For example with the urls database and its urls table, I can successfully open mysql.exe or phpMyAdmin and use urls;. I can even show tables; to see the expected table, but then when I try to describe urls; or select * from urls;, it complains that the table does not exist (even though it just listed it). (The MySQL Administrator lists the databases, but does not even list the tables, it indicates that the dbs are completely empty.) The problem now is that I have already deleted the SQL file (and cannot recover it even after scouring my hard-drive). So I am trying to figure out a way to repair these databases/tables. I can’t use the table repair function since it complains that the table does not exist, and I can’t dump them because again, it complains that the tables don’t exist. Like I’ve said, the data itself is still present in the .ibd files and the table names are present. I just need a way to get MySQL to recognize that the tables exist in the databases (I can find the column names of the tables in question in the ibdata1 file using a hex-editor). Any idea how I can repair this type of corruption? I don’t mind rolling up my sleeves, digging in, and taking a bunch of steps to fix it. Thanks a lot.

  Read the article

• Puppet: is it ok to "force" certname when you expect to shuffle nodes around?

  - by Luke404

  We all know (good example on SF) that Puppet hostname detection could be... fun. At our company (and I guess we're not alone at this) we usually pre-configure servers at our offices and test them before bringing the gear to a remote datacenter and rack them. Of course the reverse dns will change when doing that, even if we don't change the actual hostname of the system. We're slowly drafting our puppet setup and I'd like to be sure those moves won't create problems. My idea is to explicitly configure the desired full FQDN of the system as certname in puppet.conf at server provision time (before the very first puppet run). My process would look something like this: basic o.s. installation basic network configuration, enough to reach the internet and resolve dns install puppet and set up certname start puppet and let him manage the whole configuration test, fix problems in config (via puppet), re-test, and so on... manually stop puppet set up new network configuration for the datacenter network move the machine to DC turn it on puppet should automatically start and keep on doing its job The process is supported by detecting the environment in puppet's manifests (eg. based on subnet, like they do at Wikimedia) and modify configuration as needed (eg. resolv.conf contents appropriate for each network). Each node's certname will never change for the whole system life cycle. Is there any problem with this approach? Could it be improved?

  Read the article

• Passive mode FTP file download hangs from specific machine

  - by chiptuned

  I have a server which is an AWS instance that just cannot download files from a specific FTP server. I can connect to the FTP server fine and run some commands, but when I request a file it just hangs. Here is the debug output of the base linux ftp client after login: ---> SYST 215 UNIX Type: Apache FtpServer Remote system type is UNIX. ftp> get outgoing/catalog.gz catalog.gz local: catalog.gz remote: outgoing/catalog.gz ---> PASV 227 Entering Passive Mode (64,156,167,125,135,191) ---> RETR outgoing/catalog.gz 150 File status okay; about to open data connection. Thats it. Then it just sits there and nothing transfers. I have verified that a data connection is made but the client gets no data. ? ss -nt dst 64.156.167.125 State Recv-Q Send-Q Local Address:Port Peer Address:Port ESTAB 0 0 10.185.147.150:41190 64.156.167.125:21 ESTAB 0 0 10.185.147.150:48871 64.156.167.125:48557 The FTP server is not in my control and downloads from other FTP servers in passive mode have worked. Active mode does not work as the system is behind a firewall. Every FTP client I've tried has the same problem. The download works from other systems, even from other AWS instances I have with the same Security Group. Not necessarily the same distro or config though. I understand it may be some issue on the server side, but I want to know what it is about my particular machine where the transfer hangs and where on every other machine I can get my hands on, it works. Please let me know what the culprit on the client side could be or ideas on what else to look at.

  Read the article

• How do I connect to and factory reset a Catalyst 3560 Switch?

  - by Josh

  My company just bought another company. In their server room they had some older hardware, which I would like to repurpose. One of these is a Cisco Switch: C3560G-48TS-S. I found some instructions about this switch here but this is not a guide for a beginner. I have no idea how to connect to this thing to begin running the commands. It says Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. But I can't find anything on how to do this (assuming with telnet?) or even what program to use. I also don't know how to find the IP address of the device to connect to it. My research also says once I get in there, I need to run clear config all Is this the right command? Also, what if I can't get the username and password for these devices? Is there some way to factory reset (my only experience is with devices that have a hardware reset button) EDIT: I should note that when I push the button on the front the three lights blink, which according to the documentation indicated the switch is configured and "not available for express setup"

  Read the article

• Server on blacklist

  - by Cudos

  I have a Debian Wheezy server with several websites with separate domains. Some of these websites uses Wordpress and in turn uses PHP's mail function to send mail. I installed "sendmail" to be able for the server to send mail from PHP. We use Google Apps for our customers, so no need to setup a regular mail server. Now the server is blacklisted at www.spamhaus.org and get this message: This IP address is HELO'ing as "localhost.localdomain" which violates the relevant standards (specifically: RFC5321). I have tried to follow the instructions on these websites with no luck: http://www.cardiothink.com/downloads/README.spamhaus-and-blocked-email.html http://centosbeginer.wordpress.com/2011/07/12/how-to-remove-ip-in-cbl-spamhaus/ Can you please help me figure out how to configure the server? File: /etc/hosts # nameserver config # IPv4 127.0.0.1 somedomain.dk xxx.xxx.xxx.xxx server.somedomain.dk bigby # # IPv6 ::1 ip6-localhost ip6-loopback xxxx::0 ip6-localnet xxxx::0 ip6-mcastprefix xxxx::1 ip6-allnodes xxxx::2 ip6-allrouters xxxx::3 ip6-allhosts xxxx:xxx:xxx:xxxx::2 Debian-76-wheezy-64-minimal File: /etc/hostname bigby somedomain.dk is a made up domain. In reality another domain name I have on this server along with other domains. bigby is also a made up name. It is also something else in reality.

  Read the article

• How to set up a server without a hosting control panel

  - by A4J

  I have always used a control panel on my dedicated servers - from cPanel to Plesk to Virtualmin, and I am now considering ditching a CP altogether and manually editing config files. My requirements are fairly simple, I will host multiple sites on the server; some Apache with PHP & Mysql and some Passenger with Rails & Postgres. All will require email smtp/pop. FTP/Stats will not be required. Could someone please give me a quick run-down of what I would need to do - in terms of installing software and configuration? My server will come with a base install of CentOS 6.4 minimal. My thoughts so far: Install/update latest versions of MySQL & Postgres (are they 'safe' out of the box? Or do I need to do anything else like set up root passwords etc?) Install Apache & PHP (again, are the base installs good to go or do they require security tweaks?) Set up nameservers/hostnames/reverse DNS etc (Any guides on how to do this please?) Install Rubygems Install and configure Dovecot and Postfix (any tips on doing this? Or links to how-tos that cover it please?) Set up each website - any links to guides on how to do this? Install/configure firewall (or is the default install good to go?) Any other tips or advice would be greatly appreciated, as would links to guides or how-tos.

  Read the article

• Transfer iptables rules to another server (almost) real time

  - by MrShunz

  I'm running 2 cPanel servers with ConfigServer Security & Firewall plugin. One of the functions of the plugin is to block via iptables (temporarily and/or permanently) IPs which fail various authentications (POP3/IMAP, SMTP, FTP, webmail, mod_security and such). Now, i'd like to push those IP blocks to the border router to drop packets as soon as possible (and doing so protecting the other machines on the network). Keep in mind that after N failed logins IP is blocked for 5 minutes, then re-allowed. If multiple bans occours in an hour IP is blocked permanently and should be unlocked "by hand". So I need a near realtime solution. What I'm looking for is a better way than firing some cronjobs both on cPanels and border router to: dump the rules to file transfer the file to border router (via scp/sftp) load the rules from the file in the border router I'm aware that I will need some scripts to parse and modify the rules as cPanels have one ethernet interface and some aliases while border router has two ehternet interfaces and some loopbacks. All machines involved use Linux. EDIT as per @pjmorse comment. The plugin consists of a bunch of perl and config files. The part I'm intrested in is a process which scans logfiles (lfd) and installs iptables rules (and sends an alert email). Fact is, it upgrades quite often (one or two times a week) and itself is 7000 lines of perl so I'm not comfortable on tampering with it.

  Read the article

• zfs pool error, how to determine which drive failed in the past

  - by Kendrick

  I had been copying data from my pool so that I could rebuild it with a different version so that I could go away from solaris 11 and to one that is portable between freebsd/openindia etc. it was copying at 20mb a sec the other day which is about all my desktop drive can handle writing from the network. suddently lastnight it went down to 1.4mb i ran zpool status today and got this. pool: store state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected. action: Determine if the device needs to be replaced, and clear the errors using 'zpool clear' or replace the device with 'zpool replace'. see: http://www.sun.com/msg/ZFS-8000-9P scan: none requested config: NAME STATE READ WRITE CKSUM store ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c8t3d0p0 ONLINE 0 0 2 c8t4d0p0 ONLINE 0 0 10 c8t2d0p0 ONLINE 0 0 0 it is currently a 3 x1tb drive array. what tools would best be used to determine what the error was and which drive is failing. per the admin doc The second section of the configuration output displays error statistics. These errors are divided into three categories: READ – I/O errors occurred while issuing a read request. WRITE – I/O errors occurred while issuing a write request. CKSUM – Checksum errors. The device returned corrupted data as the result of a read request. it was saying low counts could be any thing from a power flux to a disk event but gave no suggestions as to what tools to check and determine with.

  Read the article

• Automatically reconnect to VPN when it drops

  - by IAmAI

  I use OpenVPN to connect to a VPN service. I will often use it unattended and on occasion I have come back to find the service disconnected and GUI asking for login credentials. If the connection is disconnected by the service, and not me, I'd like it to attempt to reconnect automatically with no intervention from me, and ideally, if the reconnection attempt initially fails, keep attempting to do so at regular intervals until a connection is successfully. Is there anyway to configure OpenVPN to do this? If not, can someone suggest a way of doing it with scripting (I use Windows)? Failing that, can anyone suggest a VPN solution that does this? The VPN provider supports PPTP as well as OpenVPN. I have configured OpenVPN to read login credentials from a file. Below is my config script. I have censored any details specific to the VPN provider. client dev tun proto tcp remote ???.???.??? 0000 resolv-retry infinite nobind persist-key persist-tun ca ???.???.??? verb 3 mute-replay-warnings float reneg-sec 0 auth-user-pass auth.conf auth-nocache Thanks for your help.

  Read the article

• zsh : How to list directory content with tab?

  - by Philippe CM

  I just switched from BASH to ZSH and thing are pretty good, but: when I start typing cd /usr/share/s and hit TAB, this is what I get : $ cd /usr/share/sane/ sane/ skype/ ssl-cert/ screen/ smplayer/ strigi/ seed-gtk3/ snmp/ synaptic/ sgml/ software-properties/ system-config-printer/ sgml-base/ soprano/ sysv-rc/ sgml-data/ sounds/ simple-scan/ splashy/ And this is ok. If I then hit TAB again, I get $ cd /usr/share/screen/, the next candidate, witch is also OK. (BTW, how do I cycle back to the previous candidate? Sorry, on to my question) Now what if I want to see the contents of /usr/share/screen/ now ? You now, BASH-style? The cursor is at the end of the line, will I have to ctrl-a (or home), then del del (to erase cd) then ls then ENTER? That seems like a lot of typing. (And it - possibly unnecessarily - enters the command in the history) Would not there be a key (maybe modifier-TAB? but the obvious candidates are already taken by the desktop... I digress) that would tell zsh to stop cycling through /usr/share/ and instead, just list the content /usr/share/screen/ ?

  Read the article

• Hardware testing tool/suite

  - by Aviator

  Hi All, I just bought a new core i5 system (assembled) and started installing Windows 7. It was failing for many times and at some point got installed. After that, frequent crashes related to MEMORY. So checked the RAM using memtest86+ and found many errors.I got it replaced with the vendor and now if i install ANY OS, at some point in installation it either freezes completely with no response for hours, or restarts automatically. I tried installing Windows 7, Windows Vista and Ubuntu 9.10. I tested the new RAM again and found no problems in about 2 passes using memtest86+. I even updated the BIOS using bootable USB and even the problem persists. I am really not sure which hardware is causing trouble. I dont have any OS inside it, so i have to check using bootable CDs DVDs and USB only. Please advice on how to proceed. Are there any suites/ separate tools for checking integrity of each hardware parts and troubleshoot it? I wanted to confirm which part is problematic before going for replacement. Thanks a lot! This is the config: Core i5, MSI P55-GD65, GSKill 2x2GB, Seagate 500GB 7200rpm, CM Extreme 600W PSU, Saphhire Radeon 5770 1GB, LG DVD Writer

  Read the article

• How do I install Apache Portable Runtime?

  - by apache

  My Apache is installed by yum install apache And now I'm trying to install subversion server from source following instructions here. But when I try to configure,get an error: [root@vps303 subversion-1.6.9]# ./configure configure: Configuring Subversion 1.6.9 configure: creating config.nice checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes ... checking for APR... no configure: WARNING: APR not found The Apache Portable Runtime (APR) library cannot be found. Please install APR on this system and supply the appropriate --with-apr option to 'configure' or get it with SVN and put it in a subdirectory of this source: svn co \ http://svn.apache.org/repos/asf/apr/apr/branches/1.2.x \ apr Run that right here in the top level of the Subversion tree. Afterwards, run apr/buildconf in that subdirectory and then run configure again here. Whichever of the above you do, you probably need to do something similar for apr-util, either providing both --with-apr and --with-apr-util to 'configure', or getting both from SVN with: svn co \ http://svn.apache.org/repos/asf/apr/apr-util/branches/1.2.x \ apr-util configure: error: no suitable apr found How do I get around this problem? BTW,will both client and server software be installed by compiling from source?

  Read the article

• Limited bandwidth and transfer rates per user.

  - by Cx03

  I searched for a while but couldn't find anything concrete, hopefully someone can help me. I'm going to be running a Debian server on a gigabit port, and want to give each user his/her fair share of internet access. The first objective is easy - transfer rates (speed) per user. From what I've looked at, IPTables/Shorewall could do the job easy. Is this easy to setup, or could one of you point me at a config? I was hoping to limit users at 300mbit or 650mbit each. The second objective gets complicated. Due to the usage of the boxes, most of the traffic will be internal network traffic that does NOT get counted to the quota. However, I still need to limit the external traffic, and if they go over, cut off access (or throttle traffic to a very low speed (10mbit?)). Let's say the user has a 3TB external traffic limit. The IF part is: If the hostname they are exchanging the traffic with DOES NOT MATCH .ovh. or .kimsufi. (company owns multiple TLDs), count to the quota. Once said quota exceeds 3TB, choke them. Where could I find a system to count that for me? It would also need to reset or be able to be manually reset on a monthly basis. Thanks ahead of time!

  Read the article

• Can anyone help me make my reverse proxy actually cache?

  - by Lenary

  Hi folks, I'm trying to configure a Reverse Caching Proxy but so far have had no luck. I would preferrably like to use apache (that will be all it will be used for), but am open to solutions using other software that can also run on Mac OS X 10.6 (I have also tried using Varnish and Squid, but with no more luck). We're running a system with about 80 mac mini clients that will be requesting lots of video from a server. To reduce load, we thought we could use Apache (which comes on the macs by default) to cache this video forever (or at least as long as possible) onto the macs' disks. I have managed to get a reverse proxy set up with apache using ProxyPass etc, but when i tried to add CacheEnable disk / to the configuration, nothing happened (i do have mod_disk_cache included). Can anyone help with my issue? The apache config file is here Thanks in advance Edit: So far I have been testing it with smaller text files, and it hasn't been caching properly. This suggests it is nothing to do with us actually downloading video, but actually to do with the cache configuration.

  Read the article

• Nginx: Rewriting directory path to file

  - by Doug

  I'm a little new to Nginx here so bear with me - I want to rewrite a url like foo.bar.com/newfoo?limit=30 to foo.bar.com/newfoo.php?limit=30. Seems pretty simple to do it something like this rewrite ^([a-z]+)(.*)$ $1.php$2 last; The part that I am confused about is where to put it - I've tried my hand at a some location directives but I'm doing it wrong. Here's my existing virtual host config, where should I implement my rewrite? server { listen 80; listen [::]:80; server_name foo.bar.com; root /home/foo; index index.php index.html index.htm; location / { try_files $uri $uri/ /index.html; } location /doc/ { alias /usr/share/doc/; autoindex on; allow 127.0.0.1; deny all; } location ~ \.php$ { try_files $uri =404; fastcgi_split_path_info ^(.+\.php)(/.+)$; include fastcgi_params; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_pass unix:/tmp/php5-fpm.sock; fastcgi_index index.php; } } Thanks!

  Read the article

• mod_rewrite with AJAX applictions: possible?

  - by MrJackV

  I am trying to run Shell In a Box (link) through another server (the computer running shellinabox is not accessible from the internet) . Ideally I could use ProxyPass in the Apache config to have a reverse proxy. Problem is I can't access the conf file. So I tried using .htaccess and I discover that I cannot use ProxyPass in there. So I tried and used mod_rewrite to do the job. Currently I have the following on the .htaccess file RewriteEngine On RewriteRule ^$ http://10.1.13.236:4200/ [P] However while it displays the title correctly and if I open up the source code I can see there is something in the page, nothing is diplayed on the screen (it remains blank). My suspicion is that there are problems with AJAX and this kind of proxy. What I am trying to accomplish with the mod_rewrite as close as possible behaviour to ProxyPass (Mirorr a website in a subdirectory). Is this possible? Is there some other solution (I tried phproxy and khproxy but neither of them is able to display anything)? Thanks in advance

  Read the article

< Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >