Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 49/287 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• Problems with NAT Adapater since upgrade to Ubuntu 12.10

  - by jjesse

  I was running Ubuntu 12.04 w/ VirtualBox installed. I was using the NAT interface to connect to everything. Basically running VBOX for testing some things and a Windows VM for Netflix.. Was back to working in my VMs today and noticed that I was unable to connect to the internet. In the VM settings I'm using the NAT adapter, however I noticed there is no NAT adapter in the Network Settings under Preferences in VBOX. Not quite sure what happened but wonder what is going on? I noticed there are some posts about changes DNSMASQ and configuring a bridge mode, but this worked out of the box under 12.04 and since the upgrade this no longers work. Need some help please

  Read the article

• unreachable subnet in one direction

  - by Carl Michaud

  I'm unable to route traffic to a subnet in my home. Here's my topology: INET <- Router A <- Router B <- WIFI AP where: Router A - ARRIS TG862G/CT (from comcast) - WAN DHCP, LAN 10.0.0.99 Router B - Linksys WRT400N with DD-WRT - WAN 10.0.0.12 , LAN 10.0.1.1 I was able to use DD-WRT to configure a static route for the 10.0.1.x network back to the 10.0.0.x network. But I'm not sure if i can do the reverse on the ARRIS router and was looking for suggestions on how to fix that. I've set things up this wasy because I am using OpenDNS to mange internet content for my kids and of course I wasn't able to configure DNS to my liking on Router A either. So at present I'm using Router A on 10.0.0.x to provide a private unfiltered WIFI AP (no ssid broadcast) that I use for netflix only and then I use router B to provide a filtered WIFI AP for the rest of my WIFI devices on 10.0.1.x. However I would like to be able to connect to my 10.0.1.x devices from the internet via dynamic dns; but I can't see anything behind router B this way. Thoughts?

  Read the article

• Client side prediction/simulation Question

  - by Legendre

  I found a related question but it doesn't have what I needed. Client A sends input to move at T0. Server receives input at T1. All clients receive the change at T2. Question: With client-side prediction, client A would start moving at T0, client-side. All other clients receive the change at T2, so to them, client A only started moving at T2. If I understand correctly, client B will always see client A's past position and not his current position? How do I sync both client B and client A?

  Read the article

• how to find 3g modem signal strength with out AT commands?

  - by neckTwi

  when i try to find signal strength of my modem using AT+CSQ, the usb device is locked by the network manager. To find the signal strength with AT+CSQ i have to first disable network connection using #nmcli nm wwan off to unlock the device inode /dev/ttyUSBX. Is there any nmcli option to get signal strength or any other option? EDIT The gdbus object for NetworkManager don't have any method like getSignalStrength. Network manager is locking device file preventing to use AT commands. nm-applet was able to display signal strength in system tray. so there should be a way to get signal strength form network manager! nmcli is command line counter part of nm-applet. Can i get signal strength using nmcli? nothing about signal strength is mentioned in its man pages.

  Read the article

• Ubuntu Desktop on PC as an IPv6 router?

  - by Cliff

  I have a DELL PC with Ubuntu 12.10 and a pandaboard running the latest linaro ubuntu 12.08. The Ethernet on the panda board is reporting 'no ipv6 router present' regardless of what router I connect (they are all probably not ipv6). I can connect via a cross-over Ethernet cable the pandaboard to the DELL PC. Can I setup the DELL PC to act as an IPv6 router. the PC has a wireless connect to our router/ADSL box. I would Really appreciate some help here so if you have an alternative please suggest it.

  Read the article

• Internet slow on one router only [the problem only in Ubuntu] [on hold]

  - by mrSuperEvening

  Internet works perfectly on every other router, but browsing sucks at home (slow browsing and slow loading times). I changed DNS servers to 8.8.0.0, still doesn't help. And funnily, download speed is extremely high on this network (meaning torrents for example), but using browsers and loading websites is extremely slow (only on this network). Do I need to change something in router settings or what can I try? By the way, I use wired connection to router. EDIT: There's no problems when using Windows. EDIT: ifconfig: eth0 Link encap:Ethernet HWaddr f2:4d:a0:c0:3f:4c inet addr:192.168.11.8 Bcast:192.168.11.255 Mask:255.255.255.0 inet6 addr: fe80::f24d:a2ff:fec6:3f4c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:206798 errors:0 dropped:0 overruns:0 frame:0 TX packets:219570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76680734 (76.6 MB) TX bytes:21738160 (21.7 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:160 errors:0 dropped:0 overruns:0 frame:0 TX packets:160 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11094 (11.0 KB) TX bytes:11094 (11.0 KB)` ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (213.159.32.147) 56(84) bytes of data. 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=1 ttl=61 time=0.936 ms 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=2 ttl=61 time=0.937 ms --- google.com ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.936/0.936/0.937/0.030 ms

  Read the article

• Static IP breaks Network connection

  - by Pasquale Tedesco

  I am somewhat new to Linux. I am setting up a Web server and installed Ubuntu server 14.04 on an vSphere ESXi 5.5 host. I am connecting perfectly fine to the internet when using DHCP but when I apply my Static settings I loose the ability to connect to websites. Whats weird is I can Ping google.com but if I try wget gooogl.com it hangs at connecting to google.com (google.com):173.194.43.32:80 and I get "failed: connection refused" But if I am set to DHCP the connection resolves perfectly. Thanks # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 #iface eth0 inet dhcp iface eth0 inet static address 10.1.2.25 gateway 10.1.2.2 netmask 255.255.255.0 search tsig.com dns-nameservers 10.1.2.13 10.1.2.30

  Read the article

• How to connect ethernet on ubuntu (with auto-detection by Ubuntu)

  - by user12285

  Do I need to post another thread for the same? If so, sorry. Yes, I saw that it's been well over six months but I have the same router SmartAX MT880d with ethernet, and the exact same problem, that is no internet even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. Sorry if I don't use the right (technical) terminology to express my issue. English is not my mother tongue. I'm a total beginner with ubuntu. My internet works great in Windows but does not work in Ubuntu. For 2 weeks, I've kept reading on the web and forums and the ubuntuguide.org to name a few but to no avail. Now I see no other solution but to ask for help. My problem is that as a beginner, I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files (eg: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm confused between putting figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem?? Is the subnet 255.255.255.0? Gateway 192.168.1.1. I'm confused as I can also see a different IP starting with 155131*** (is it an account number? no clue again) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

  Read the article

• accessing files on a shared folder via IIS

  - by Darkcat Studios

  Im not sure if this suits stackexchange, serverfault or here... so i'll go with here for a start. I'm having issues setting up a network share to be accessed by IIS, all I need to do is read/write files on the Other server. We have 2 servers set up (Both 2008 R2 & IIS 7.5), one is the WEB server, which is externally accessible and NOT part of the domain. We also have an Intranet server which has no internet connectivity and is part of the domain. These 2 servers can talk to each other happily, I have the SQL server on the WEB server shared across to the intranet server so that the web content is editable from the intranet. I can share a folder on the web server (say, wwwroot/Images/) and connect to it from the intranet server, even have it as a mapped drive (but i know thats not going to work for IIS to access it), So there seems not to be a connectivity issue. I can also set up a Virtual folder in IIS on the Intranet server - this is where it gets annoying - I cant connect using pass-through authentication because there is no suitable user on the web server (which is not on the domain). If i set up a user on the web server, eg Intranet_USR, and give it appropriate rights to the folder, files and share, i can connect, but only view folder contents in IIS, not read, although that user has read privileges!! Any help much appreciated!

  Read the article

• ubuntu nic card issue

  - by Blainer

  I am trying to install NIC r8168 and it shows everything installed ok. It is a brand new NIC and the lights wont come on when I plug in a ethernet. The NIC is that is not working is eth0. Why does it show the r8168 driver being used by 0? My NIC model number is ST1000SPEX if anyone is wondering. lsmod Module Size Used by r8168 215669 0 ifconfig eth0 Link encap:Ethernet HWaddr 00:0a:cd:1e:0a:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:19:d1:1d:f6:7a inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::219:d1ff:fe1d:f67a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:551467 errors:0 dropped:0 overruns:0 frame:0 TX packets:145219 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:409744342 (409.7 MB) TX bytes:12233173 (12.2 MB) Interrupt:21 Memory:dfde0000-dfe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:280 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22608 (22.6 KB) TX bytes:22608 (22.6 KB) Ubuntu 11.10 x64 Kernel 3.0.0-12-generic

  Read the article

• Ubuntu 12.04 USB wireless not recognized

  - by Justin

  I have searched for awhile now for ways to fix my problem but have come up with nothing. I am running Ubuntu 12.04 on my desktop computer. I am unable to find the Enable Wireless button in the network area. It just doesn't appear. Everything else works on my laptop. I believe it's the drivers for my USB network adapter. I also have no way of using a wired connection at the moment. Thanks for any help!

  Read the article

• Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

  - by user42424

  So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

  Read the article

• How to create shared home directories across multiple computers?

  - by Joe D

  I know there are ways to share a folder across computers making it easy to move files. But I was wondering how one would setup a single login which lets you access the same files regardless of which machine you login on? What I would like is something similar to something you would see in a college campus where students login on machines in the lab and see their files regardless of which machine they use. I know there are server involved here. I have a need to create this on a smaller scale where we have a few computers available (and one of these could act as the server if needed and host the files) that every one shares. Note, the specific install of software might be different on each computer but the login and OS are the same. Since some computers have additional capability that our group members will need to use at rotating schedules (software licenses or hardware components, etc.). I have not done this before, so I would appreciate detailed instructions if possible or a reference to a guide that describes this. Thanks in advance.

  Read the article

• When Ubuntu Server restarts eth0 Doesn't come back up

  - by JoelGsus

  Every time I restart my Ubuntu Server 11.10 I can't ssh into it because ETH0 doesn't come up automatically. I never had this problem before upgrading to 11.10. I have to login to the server and start the ETH0 manually. I would appreciate it any help. Thanks. Here is my /etc/networks/interfaces file: #The loopback network interface auto lo eth0 iface lo inet loopback # The primary network interface iface eth0 inet static address 192.168.1.102 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 gateway 192.168.1.1

  Read the article

• audio and video data in RTP

  - by Banana

  Suppose a user wants to transmit both audio and video to another user, whose formats are AMR for audio and H.264 for video. Does the user have to transmit audio and video packets always separately? Meaning that it is not possible to mix audio and video within the same RTP packed, is that correct? If this is true I guess the RTP protocol will need to know the SSRC of both audio and video to be able to check the sync of the two streams.

  Read the article

• Ethernet Wired Connection Help

  - by user107598

  I have recently installed Ubuntu 12.10 onto my Dell Inspiron N5010 and Ive been all over many forums trying to figure out how I can get my ethernet cable to be recognized so I can set up a wired connection. My Network Card is the Realtek RT8139 and from what Ive gathered the ethernet port driver for it is installed. Whenever I run ifconfig in the terminal it says that eth1 is up and running but no matter how I edit the connection I cannot get it to work. If anyone can help it would be greatly appreciated!

  Read the article

• Problems with No-IP redirecting

  - by user171156

  I am setting up a webserver on my ubuntu desktop 13.04, everything is working fine except; When trying to access the server through the external host using no-ip, it gives the original index created by apache on setup. While when I try to connect to the server via my real IP address from externally, it goes to the correct index. I have been trying to figure out what the issue is on this problem as nothing is working because of that bad redirect, I'm wondering if anyone of you could help me out, or advise me in the right path. Thank you very much! PS; If more info needed I'll provide, but this should explain it all.

  Read the article

• Wireless ad-hoc network between Ubuntu and MS Windows

  - by nixnotwin

  I have setup a wireless ad-hoc connection between two laptops: one running ubuntu and the other MS XP. I have assigned static IP to both the laptops and both get connected quite easily. I can access all ubuntu services like ssh, squid, samba from the laptop running MS Windows. But from Ubuntu machine I cannot access any Windows services like shared directories etc. The Windows machine doesn't even respond to ping requests from ubuntu.

  Read the article

• mount remotely mybook live network drive

  - by bob

  I have a mybook live western digital 1TB hard disk connected to fritzbox 7270 router in office. When I am in the office, I can mount this drive to ubuntu since I have added to the etc/fstab file: //192.168.178.30/user /home/user/DISK cifs auto,iocharset=utf8,user=user%password 0 0 Is there a similar, easy & safe way, to do the same when I am out of the office using the static IP of the fritzbox router? I have already added tcp port forwarding in the router for ports 8080 (to 80 of the disk) and 8443 (to 443 of the disk). Thank you in advance

  Read the article

• Unable to remove network proxy

  - by Rushil

  I'm on 11.10 I'd set up a network proxy a couple of days back from system settings .And afterwards I'd set my proxy method back to none. However, my proxy has not been removed. I know this because: a: 127.0.0.1 routes me to the index.html file in the base directory of the proxy server. b: I'm able to access my university internet after hours. I checked my /etc/environment and etc/apt/apt.conf file and both of them have no proxy details. I also tried resetting the proxy and then getting rid of it but that didn't work either.

  Read the article

• Application to organize / manage installed networks

  - by vicmp3

  I was wondering if there is a Application where you can organize networks. I mean if you have installed some networks you have to note every pc's name, his ip-address and so on. Is there a Application where you can manage it? I saw the monitoring tools but that is not exactly what I'm looking for. Maybe I didnt explain me well, after all my englis his not so good :) For example if I install many different networks I write in a book how I configured them. I write pc-name ip-address ip-gateway ip-broadcast and so on for each network. It will be great if I can do it in a program to organize it well, and for example it gives me a node view of the network.

  Read the article

• atheros wireless ar9285 driver

  - by nikola

  I have been having problems with wireless on Ubuntu 10 and above, Mint 11 and above. The problem is in the driver for the wireless... I can see that there is no driver installed and yet it works but reduced a lot, for example: on windows 7 ultimate 100% on distance of 1 meter (currently running) Mint Cinnamon 15 on same distance 70% when it goes under the 40 % it simply disconnects and than takes a lot of time to connect again I am new to Linux and I don't know anything about programming, yet I love the interface and look of the OS but don't want to reject it for couple of problems. There is, however, a problem with brightness control on laptop, it shows the notification and slider but with no effect The question is: Can somebody explain to me where to download and how to install the ar9285 driver for atheros wireless card laptop acer emachines eme529? or can someone explain this to me only for the LINUX MINT 15 http://www.jrhenkelmann.net/index.php?option=com_content&task=view&id=34 because the synaptic's interface is different than of mint 15 I KNOW this is Ubuntu community but the problems persist in all Linux versions

  Read the article

• connecting ubuntu with 7 via network cable

  - by VeXe

  i was tryin to connect my ubuntu toshiba satalite L650 laptop with my desktop via a network cable so that i can share things and remotely control the desktop from the laptop, i googled the problem out and found a guide page , i followed all the steps , i installed samba, i had the two computer have the same workgroup name , i had everything correct, but i still dont see connection estbalished between the two computers, (neither one is visible to the other) what is missing ? thanx in advance.

  Read the article

• Serializing network messages

  - by mtsvetkov

  I am writing a network wrapper around boost::asio and was wondering what is a good and simple way to serialize my messages. I have a message factory which can take care of dispatching the data to the correct builder, but I want to know if there are any established solutions for getting the binary data on the sender side and consequently passing the data for deserialization on the receiver end. Some options I've explored are: passing a pointer to a char[] to the serialize/deserialize functions (for serialize to write to, and deserialize to read from), but it's difficult to enforce buffer size this way; building on that, I decided to have the serialize function return a boost::asio::mutable_buffer, however ownership of the memory gets blurred between multiple classes, as the network wrapper needs to clean up the memory allocated by the message builder. I have also seen solutions involving streambuf's and stringstream's, but manipulating binary data in terms of its string representation is something I want to avoid. Is there some sort of binary stream I can use instead? What I am looking for is a solution (preferrably using boost libs) that lets the message builder dictate the amount of memory allocated during serialization and what that would look like in terms of passing the data around between the wrapper and message factory/message builders. PS. Messages contain almost exclusively built-in types and PODs and form a shallow but wide hierarchy for the sake of going through a factory. Note: a link to examples of using boost::serialization for something like this would be appreciated as I'm having difficulties figuring out the relation between it and buffers.

  Read the article

• Configure application priority to access the network

  - by Mario

  I noticed that when I am running applications such BitTorrent all the other applications have trouble accessing the network. I am sure it would be possible to limit BitTorrent's network usage but what I really want is to be able to set priorities to applications (or protocols) accessing the network. For example, let's say I put max priority for the browser (or http) and then, no matter how much bandwidth was using at the time, the http packets would always go through. Is this possible? Is there an application for Ubuntu to do this or a way to configure this on Ubuntu directly?

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >