Search Results

Search found 16914 results on 677 pages for 'single threaded'.

Page 497/677 | < Previous Page | 493 494 495 496 497 498 499 500 501 502 503 504  | Next Page >

• Formatted C: from Windows 7 setup, now it won't even install

  - by ocurro

  Help, I'm so confused. I did more or less what's been described here: I formatted Vista and installed Windows 7 over it. Problem is that I'm now unable to boot (...) [1] I'm installing Seven on top of Vista on ACER AS1410 Notebook When it comes to the part where I choose where to install, I pick the partition labeled C: but instead of keeping windows.old files (what would I want them for?) I choose to go and carelessly format the partition (my bad). It shows me this error: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information Now the only option is "Load Driver". i have tried installing every single one from ACER website, none of them are useful. I even flashed orig. BIOS. I've tried going back and choose "Repair" like in the picture:[2] but I only get an error: "Failed to save startup options" I think this is weird, what else can I do? [1] superuser.com/questions/117076/formatting-of-an-xp-vista-dual-boot-machine-now-unable-to-boot-up-xp [2] www.howtogeek.com/wp-content/uploads/2007/08/image51.png

  Read the article

• check_snmp warning & critical thresholds with negative values

  - by Oesor

  I'm querying some signal level values measured in dBm, and the SNMP host on the remove device reports the values as negative values, ie, -90 dBm. However, check-snmp seems to be incapable of dealing with negative numbers as part of its threshold values. If I specify the values as part of a collection of OIDs, it accepts the syntax but converts the snmp value to positive, thus always generating a WARNING/CRITICAL result: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::AverageReceiveSNR.0,DEVICE-MIB::CurrentNoiseFloor.0 -w 10:,~:-85 -c 15:,~:-80 -vvvv /usr/bin/snmpget -t 1 -r 5 -m ALL -v 1 [authpriv] 192.168.1.100:161 DEVICE-MIB::AverageReceiveSNR.0 DEVICE-MIB::CurrentNoiseFloor.0 DEVICE-MIB::AverageReceiveSNR.0 = INTEGER: 25 DEVICE-MIB::CurrentNoiseFloor.0 = INTEGER: -97 Processing line 1 oidname: DEVICE-MIB::AverageReceiveSNR.0 response: = INTEGER: 25 Processing line 2 oidname: DEVICE-MIB::CurrentNoiseFloor.0 response: = INTEGER: -97 SNMP CRITICAL - 25 *97* | DEVICE-MIB::AverageReceiveSNR.0=25 DEVICE-MIB::CurrentNoiseFloor.0=97 If I run it with a single OID, it gives me an error that the format is incorrect: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::CurrentNoiseFloor.0 -w ~:-85 -c ~:-80 -vvvv Range format incorrect And if I run it with no thresholds defined, it works properly and returns the right value. This makes the graphs correct, however it'll never generate a notification when out of range: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::CurrentNoiseFloor.0 -vvvv /usr/bin/snmpget -t 1 -r 5 -m ALL -v 1 [authpriv] 192.168.1.100:161 DEVICE-MIB::CurrentNoiseFloor.0 DEVICE-MIB::CurrentNoiseFloor.0 = INTEGER: -97 Processing line 1 oidname: DEVICE-MIB::CurrentNoiseFloor.0 response: = INTEGER: -97 SNMP OK - -97 | DEVICE-MIB::CurrentNoiseFloor.0=-97 What am I doing wrong here? How would I, for example, generate a CRITICAL when the noise floor is -80 dBm or higher, a WARNING when it's -85 to -80 dBm, and an OK when -85 dBm or lower? Do I have to write my own SNMP plugins when dealing with negative values?

  Read the article

• How to move Mdadm RAID drive (EBS based) to different AWS Instance

  - by Stanley

  We have a media-rich web application that is hosted on AWS. We have several Web Servers and we have an NFS server. On the NFS server (Linux server) we have several EBS volumes that are mounted and we've used mdadm to implement the different mounted volumes as a single RAID volume. The Web Servers simply access the NFS storage through a mount point. Amazon has now let us know that they will be performing power maintenance on this server in a couple of days time. Since all our media is on here it would render our site unusable for the hours while Amazon is working on it. We want to try and prevent this downtime. I was thinking that we can prevent server downtime by perhaps setting up a new server temporarily and attaching the EBS drives (raid volume) to that server and have our web servers point there during maintenance. This is a very high risk operation since this involves several terabytes of our production data. What would be the safe way to move over our logical raid drive (md0) to a new amazon instance? I was hoping that I could start with building the new server, mounting the ebs volumes and assembling the RAID partition using mdadm --assemble --scan before unmounting from the existing instance so that I can first test that everything works and thus having it mounted on two instances at the same time, but I don't believe that is possible with the way that filesystems work. How do I move a Linux software RAID to a new machine? suggests a way to move drives, but isn't really a cloud-based question. Perhaps there are simpler ways to prevent system downtime with our solution being hosted on the cloud? I have considered taking an EBS snapshot, but that tries to replicate all the many terabytes of mounted storage, so this is not a practical solution. Any ideas?

  Read the article

• 2560 x 1600 screen resolution not available when a second monitor is attached.

  - by sgmoore

  I am running Windows 7 (64-bit edition) and have a 30" Dell 3007WFP monitor which runs at a screen resolution of 2560 x 1600. This works perfectly until I try to connect a second monitor, and then the screen resolution on the main monitor immediately drops to 1280x800 and I can't change it back up to the correct resolution until I disconnect the second monitor. The graphics card is a Nvidia Quadro FX 370. This has a dual link DVI connector (to which the 30" is connected) and a single link DVI connector. The second monitor can run at 1920x1080 and is connected using a VGA to DVI connector. Note, it does not seem to matter whether the second monitor is running at 1920x1080 or even at 800x600. Windows reports Total Available Graphics Memory: 3839MB Dedicated Video Memory: 256MB System Video Memory: 0MB Shared System Memory: 3583MB Does anyone know if this a limitation with the video card, memory, drivers, connectors or something else? If this is a limitation with the video card, can anyone recommend a PCI Express 16 card that would support at least this setup, but preferably support two 30" monitors both running 2560 x 1600. (I'm not into gaming etc, so it doesn't need to be very powerful)

  Read the article

• How does the "Steam" platform work? Is it DRM? Can I trust "Steam"-powered software? [closed]

  - by Chris W. Rea

  So – I just bought the new game Supreme Commander 2. This question is not about the game, but about the online software installation platform that it seems to require. I haven't bought a game in a long time, and I'm puzzled: Apparently, SC2 is a "Steam"-powered game. When I went to install the game, it asked me to either create a new Steam account, or log in with an existing account. I clicked "Cancel" because I don't plan to play online and I don't want anything unnecessary installed on my computer, since I only plan to play single player! However, after clicking "Cancel", the installer asked for my confirmation that I indeed wanted to cancel installation of the game! I thought I was just canceling the "online" portions! So I really want to know: How do "Steam" powered games work? Is this essentially a form of DRM (Digital Rights Management)? Can I trust this software platform? Has anybody done any independent verification on how this platform works? (I'm very leery of any DRM after the Sony BMG CD copy protection scandal. Thank goodness for Mark Russinovich.) Does the "Steam" platform install anything particularly nasty or unwanted on my computer? High-rep users: Please vote to reopen this question. It is not about the game, but about the software update platform / updater / DRM. Imagine if the software in question were a productivity application. The issues remain the same.

  Read the article

• Two DHCP servers on the same network

  - by CesarGon

  We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

  Read the article

• Two DHCP servers on the same network

  - by CesarGon

  We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

  Read the article

• Cannot remove storage account because of lease, but I already deleted the server [closed]

  - by djechelon

  I recently created a temporary virtual server on Azure. Then I deleted it. I wanted to delete the storage account associated with it because I didn't need it any more. The problem is that the VHD file is still associated to a non-existing virtual machine!! If I try to delete the VHD from Virtual Machines\Disks I get the Delete button greyed and the table tells me it's still associated with the old VM. If I go to storage administration and try to delete the blob from vhds/ directory I get there is an active lease. I've read on Azure forums that, in these case, one should try to force releasing the lease from the blob. I followed their instructions and downloaded their script, but running it failed. The script detected that the disk is associated to a Virtual Machine and can't be deleted. The problem is that I'm 1000000% sure that I already deleted the VM. In fact, I currently only have a single VM that has its own HD and is up and running fine! What can I do to delete that storage account that is probably sucking money from my pocket?

  Read the article

• Why is my global security group being filtered out of my logon token?

  - by Jay Michaud

  While investigating the effects of filtered tokens on my file permissions, I noticed that one of my global security groups is being filtered in addition to the regular system-defined filtered groups. My Active Directory environment is a single-domain forest on the Windows Server 2003 functional level. I'll call the domain "mydomain.example.com". I am logged onto a Windows Server 2008 Enterprise Edition machine (not a domain controller) as a member of the "MYDOMAIN\Domain Admins" group and the "MYDOMAIN\MySecurityGroup" global security group (among others). When I run "whoami /groups" from an elevated command prompt, I see the full list of groups to which my account belongs as expected. When I run "whoami /groups" from a regular, non-elevated command prompt, I see the same list of groups, but the following groups are described as "Group used for deny only". BUILTIN\Administrators MYDOMAIN\Schema Admins MYDOMAIN\Offer Remote Assistance Helpers MYDOMAIN\MySecurityGroup Numbers 1 through 3 above are expected based on Microsoft documentation; number 4 is not. The "MYDOMAIN\MySecurityGroup" global security group is a group that I created. It contains three non-built-in global security groups, and these security groups contain only non-built-in user accounts. (That is, I created all of the accounts and groups that are members of the "MYDOMAIN\MySecurityGroup" global security group.) There are other, similar groups of which my account is a member that are not being filtered out of my logon token, and this group is not granted any specific user rights in the security settings of this computer or in Group Policy. What would cause this one group to be filtered out of my logon token?

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP. (solved)

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• RRAS with DHCP when the IP pool is on a different subnet

  - by John B

  I run a small business network and the last couple of days I have been setting up some equipment to add VPN capabilities to our network. I've got the following set up: Windows 2008 R2 with RRAS - 172.22.200.50 Cisco RV082 router - 172.22.100.1 / 172.22.200.1 The Cisco router only support DHCP on a single class C network; 172.22.100.0/24. On the Cisco router I have set up an additional subnet; 172.22.200.0/24. The DHCP range is 172.22.100.200-254 When a PPTP connection comes in to the router, it is forwarded to my RRAS at 172.22.200.50. If I configure RRAS to assign IPs from a static pool on the 172.22.200.0/24 subnet everything works fine except the DNS suffix / search domain. However, if I set RRAS to use DHCP I am no longer able to contact any devices on the network. The IP I receive is on a different subnet (172.22.100.0/24). Is it possible to still use DHCP as the method of ip assignment in RRAS, even when the IP adresses assigned are in a different subnet? If yes, what piece of configuration am I missing to fix the VPN connection issues mentioned in the paragraph above. The reason I want RRAS with DHCP to work is because from what I have understood, this is the "only" way to hand out a DNS suffix to VPN clients. Any help on this matter is greatly appreciated!

  Read the article

• Can't pin modified shortcuts to the Windows 7 task bar

  - by Coder

  I have a shortcut to a .bat file which I pin to the task bar using a workaround by using another icon and this seems to work. Now I make a copy of that shortcut, point it to a different .bat file, rename it, and I can't pin this one to the task bar. I have to find some other new unused icon to pin, pin it, then modify it manually. The other problem this causes is that windows seems to track which icons were pinned even if they are modified after the fact. As such, if I use media player as my dummy icon, pin it, then alter it's name and shortcut to point to a .bat file, I can't re-pin windows media player and if I select unpin from the windows media player, it unpins my shortcut to my .bat file. I can't believe how ridiculous this is. Is there a way to pin anything I want to the taskbar (ie. .bat file in my case) that does not cause problems like this? Is there an easy way I can copy an existing shortcut and modify it and re-pin it to the taskbar? The reason I want to copy it is because I start a .bat file (in particular git bash) and I set properties on the window like quick edit, increase the screen buffer and set it's position and size manually. I don't want to have to do this to every single icon I want to pin since they will be identical aside from the shortcut url.

  Read the article

• dhclient requests filling memory?

  - by shanethehat

  Dammit Jim, I'm a web developer, not a sys admin. With that out of the way, my client's has a CentOS server (6.2) that is only serving a single Magento site (and the associated MySQL server) and it is frequently running out of memory, despite the site only currently being open to 5 users. I'm investigating the logs to try to figure out why the memory usage is so high, but I don't really know what I'm looking at. It seems that there are a lot of entries in /var/log/messages concerning DHCP requests, approximately one every 15 seconds, that look like this: Apr 7 14:23:06 s15940039 dhclient[815]: DHCPREQUEST on eth0 to 172.30.102.85 port 67 (xid=0x6b5cd2a7) Is this normal? I don't see anything else in here that I don't recognise, but then I'm not sure I'd know the problem if I did see it. 4 days ago the server ran out of memory completely and locked up, requiring a restart. The DHCP messages did not start up again for 23 hours, but then carried on as before. I have read this question which describes the same issue, but in my case a fresh DHCP lease does not ever seem to be issued. Is this something I should push back to the hosting provider, or have I not yet found the source of the memory problem?

  Read the article

• Dynamic subdomain routing

  - by Nader

  Hi everyone, I asked this question over at stackoverflow, but got very few views: http://stackoverflow.com/questions/2284917/route-web-requests-to-different-servers-based-on-subdomain Perhaps it's more applicable to this crowd. Here it is again for convenience: I have a platform where a user can create a new website using a subdomain. There will be thousands of these, eg abc.mydomain.com, def.mydomain.com . Hopefully if we are successful hundreds of thousands. I need to be able to route these domains to a different IPs to point at a particular app server. I have this mapping in a database right now. What are the best practices and recommended technologies here? I see a couple options: Have DNS setup with a wildcard CNAME entry so that all requests go to a single IP where perhaps two machines using heartbeat (for failover) know how to look up the IP in the database and then do an http redirect to the appropriate app server. This seems clunky and slow to me. Run my own DNS server that can be programatically managed such that when a new site is created a DNS entry is added. We also move sites around to different app servers, so I would need to be able to update DNS entries in close to real time. Thoughts anyone? Thanks. Update2: I've setup external wildcard DNS pointing at an HAProxy web server whose job it is to route requests to backend servers. The mapping is stored in our internal PowerDNS server. Question now is how to get the HAProxy server (or another) to use the value of the internal DNS and not some config file or access list? – Update: Based on some suggestions below, it seems like reverse-proxy server(s) is the way to go. As I'll be rebalancing the domain-server mapping, these need to work instantly and the TTL on a DNS solution could be a problem. Any recommendations on software to use considering this domain-IP data is stored in a DB, and I'll need this to be performant?

  Read the article

• Why is my filesystem being mounted read-only in linux?

  - by Tim

  I am trying to set up a small linux system based on Gentoo on a VirtualBox machine, as a step towards deploying the same system onto a low-spec Single Board Computer. For some reason, my filesystem is being mounted read-only. In my /etc/fstab, I have: /dev/sda1 / ext3 defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 none /dev/shm tmpfs defaults 0 0 However, once booted /proc/mounts shows rootfs / rootfs rw 0 0 /dev/root / ext3 ro,relatime,errors=continue,barrier=0,data=writeback 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0 none /dev/shm tmpfs rw,relatime 0 0 usbfs /proc/bus/usb usbfs rw,nosuid,noexec,relatime,devgid=85,devmode=664 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 (the above may contain errors: there's no practical way to copy and paste) The partition at /dev/hda1 is clearly being mounted OK, since I can read all the data, but it's not being mounted as described in fstab. How might I go about diagnosing / resolving this? Edit: I can remount with mount -o remount,rw / and it works as expected, except that /proc/mounts reports /dev/root mounted at / rather than /dev/sda1 as I'd expect. If I try to remount with mount -a I get mount: none already mounted or /sys busy mount: according to mtab, sysfs is already mounted on /sys Edit 2: I resolved the problem with mount -a (the same error was occuring during startup, it turned out) by changing the sysfs and proc lines to proc /proc proc [...] sysfs /sys sysfs [...] Now mount -a doesn't complain, but it doesn't result in a read-write root partition. mount -o remount / does cause the root partition to be remounted, however.

  Read the article

• CPU / Affinity mask problem in SQL 2005

  - by Robert Moir

  Hi folks, Having a problem with a SQL Server which was virtualised. The CPU mask was set on the physical host for some reason and now advanced options are not available. So I need to reconfigure the CPU affinity mask settings - which are advanced options, so this is blocked because of the affinity mask issue. I've tried doing this from the SQL server in single user command line mode, I've googled and found lots of people with similar problems but no real solution. I'm stumped. Any ideas? Sample commands and output from query analyser below. sp_configure 'show advanced options', 1 GO RECONFIGURE WITH OVERRIDE GO sp_configure 'affinity mask', 0x00000000 GO RECONFIGURE GO ----------------------------------------- Configuration option 'show advanced options' changed from 0 to 1. Run the RECONFIGURE statement to install. Msg 5832, Level 16, State 1, Line 1 The affinity mask specified does not match the CPU mask on this system. Msg 15123, Level 16, State 1, Procedure sp_configure, Line 51 The configuration option 'affinity mask' does not exist, or it may be an advanced option.

  Read the article

• Debian - starting UFW (Uncomplicated Firewall) before network interfaces are operational

  - by Tomasz Zielinski

  I want to install UFW on Debian Lenny. Everything looks straightforward except that I don't know where to plug UFW startup script so that it configures iptables before hax0rs can break in. I've reviewed runlevel directories and in /etc/rc0.d, /etc/rc6.d and /etc/rcS.d there are items like these: S35networking -> ../init.d/networking S36ifupdown -> ../init.d/ifupdown Runlevel 0 and 6 are for shutdown and reboot so I guess nothing should be changed there, but runlevel S advertises itself (in README) like something for me: The scripts in this directory whose names begin with an 'S' are executed once when booting the system, even when booting directly into single user mode. The following sequence points are defined at this time: * After the S40 scripts have executed, all local file systems are mounted and networking is available. All device drivers have been initialized. (What bothers me is that both rc0/6.d and rcS.d point to the same networking and ifupdown scripts, but after looking at sources I believe those scripts are smart enough to figure out where to start and where to stop networking.) Now, I think that I should plug my /lib/ufw/ufw-init into /etc/rcS.d, with priority higher that the one of ifupdown and networking, i.e. <= 38 for my /etc/rcS.d. Am I right in this "analysis" ?

  Read the article

• SkyDrive broken after upgrade to Windows 8.1: "This location can't be found, please try later"

  - by avo

  Upgrading from Windows 8 to Windows 8.1 via the Store upgrade path has screwed my SkyDrive. The C:\Users\<user name>\SkyDrive folder is empty (it only has single file desktop.ini). When I open the native (Store) SkyDrive app, I see "This location can't be found, please try later". I'm glad to still have my files alive online in my SkyDrive account. I tried disconneting from / reconnecting to my Microsoft Account with no luck. Anyone has an idea on how to fix this without reinstalling/refreshing Windows 8.1? From Event Viewer: Faulting application name: skydrive.exe, version: 6.3.9600.16412, time stamp: 0x5243d370 Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0x00000000 Fault offset: 0x0000000000000000 Faulting process ID: 0x4e8 Faulting application start time: 0x01cece256589c7ee Faulting application path: C:\Windows\System32\skydrive.exe Faulting module path: unknown Report ID: {...} Faulting package full name: Faulting package-relative application ID: Also: The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID {C2F03A33-21F5-47FA-B4BB-156362A2F239} and APPID {316CDED5-E4AE-4B15-9113-7055D84DCC97} to the user NT AUTHORITY\LOCAL SERVICE SID (S-1-5-19) from address LocalHost (Using LRPC) running in the application container Unavailable SID (Unavailable). This security permission can be modified using the Component Services administrative tool. Never was a big fan of in-place upgrade anyway, but this time it was a machine which I use for work, with a lot of stuff already installed on it. Shouldn't have tried to upgrade it in the first place, but was convinced Windows 8.1 is a solid update. Another lesson learnt.

  Read the article

• SQL Server 2008 Cluster Installation - First network name always fails

  - by boflynn

  I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

  Read the article

• Domain Controller DNS Best Practice/Practical Considerations for Domain Controllers in Child Domains

  - by joeqwerty

  I'm setting up several child domains in an existing Active Directory forest and I'm looking for some conventional wisdom/best practice guidance for configuring both DNS client settings on the child domain controllers and for the DNS zone replication scope. Assuming a single domain controller in each domain and assuming that each DC is also the DNS server for the domain (for simplicity's sake) should the child domain controller point to itself for DNS only or should it point to some combination (primary VS. secondary) of itself and the DNS server in the parent or root domain? If a parentchildgrandchild domain hierarchy exists (with a contiguous DNS namespace) how should DNS be configured on the grandchild DC? Regarding the DNS zone replication scope, if storing each domain's DNS zone on all DNS servers in the domain then I'm assuming a DNS delegation from the parent to the child needs to exist and that a forwarder from the child to the parent needs to exist. With a parentchildgrandchild domain hierarchy then does each child forward to the direct parent for the direct parent's zone or to the root zone? Does the delegation occur at the direct parent zone or from the root zone? If storing all DNS zones on all DNS servers in the forest does it make the above questions regarding the replication scope moot? Does the replication scope have some bearing on the DNS client settings on each DC?

  Read the article

• Error regarding DNS - "... must be able to resolve names ..." (Windows Server 2008 R2 installation)

  - by Scolytus

  I'm trying to replace our old Windows 2000 Server by a Windows Server 2008 R2. I followed the guide at MSDN. Coming to the step "Install Active Directory Domain Services..." the option to install the DNS-Server was grayed-out. According to Microsoft Support I skipped the DNS Server Installation at this point. (Because of the single-label DNS name) I then installed the DNS-Server role and created a forward-lookup-zone for the domain. When running the Best Practices Analyzer of the DNS-Server role I get these two messages for both domain controllers (the old win2k and the new win 2008 R2): The DNS server [IP address] on [adapter name] must be able to resolve names in the primary DNS domain zone The DNS server [IP address] on [adapter name] must be able to resolve names in the forest root domain name zone The TechCenter articles suggest to use a proper DNS Server - that's pointless when I try to configure a proper DNS Server. How do I configure the DNS Server in a way that it resolves these zones? Or are these errors irrelevant? dcdiag /v /test:DNS Seems to run fine...

  Read the article

• How do I delete hardlinks, symbolic links, junction points, etc please?

  - by jonny

  I could be wrong, but I'm yet to hear a valid argument for the exploitability that these things deliver...outweighing their very dubious / debatable functionality. They seem to me to be marginally handy, but I don't think I have any need for them. I do have a need for security, however. How can I delete their entire functionality permanently from my hard drive, please? Microsoft only has pages on how to create them; which seems almost peculiar to the point of being dubious (at least, to me...) And just a dumb command line question, am I correct in assuming fsutil hardlink list c: will enumerate every single hardlink on that drive? C:\Windows\system32>fsutil hardlink list c: \Windows\System32 Also, how do I delete symbolic links please ;) But I'd just rather have all symbolic linking and recursion-creating stuff removed, if that's possible? C:\Windows\system32>fsutil behavior query symlinkevaluation Local to local symbolic links are enabled. Local to remote symbolic links are enabled. Remote to local symbolic links are disabled. Remote to remote symbolic links are disabled.

  Read the article

• ProxyPass for specific vhost with mod_rewrite

  - by Steve Robbins

  I have a web server that it set up to dynamically server different document roots for different domains <VirtualHost *:80> <IfModule mod_rewrite.c> # Stage sites :: www.[document root].server.company.com => /home/www/[document root] RewriteCond %{HTTP_HOST} ^www\.[^.]+\.server\.company\.com$ RewriteRule ^(.+) %{HTTP_HOST}$1 [C] RewriteRule ^www\.([^.]+)\.server\.company\.com(.*) /home/www/$1/$2 [L] </IfModule> </VirtualHost> This makes it so that www.foo.server.company.com will serve the document root of server.company.com:/home/www/foo/ For one of these sites, I need to add a ProxyPass, but I only want it to be applied to that one site. I tried something like <VirtualHost *:80> <Directory /home/www/foo> UseCanonicalName Off ProxyPreserveHost On ProxyRequests Off ProxyPass /services http://www-test.foo.com/services ProxyPassReverse /services http://www-test.foo.com/services </Directory> </VirtualHost> But then I get these errors ProxyPreserveHost not allowed here ProxyPass|ProxyPassMatch can not have a path when defined in a location. How can I set up a ProxyPass for a single virtual host?

  Read the article

• How does the "Steam" platform work? Is it DRM? Can I trust "Steam"-powered games?

  - by Chris W. Rea

  So – I just bought the new game Supreme Commander 2. This question is not about the game, but about the online software installation platform that it seems to require. I haven't bought a game in a long time, and I'm puzzled: Apparently, SC2 is a "Steam"-powered game. When I went to install the game, it asked me to either create a new Steam account, or log in with an existing account. I clicked "Cancel" because I don't plan to play online and I don't want anything unnecessary installed on my computer, since I only plan to play single player! However, after clicking "Cancel", the installer asked for my confirmation that I indeed wanted to cancel installation of the game! I thought I was just canceling the "online" portions! So I really want to know: How do "Steam" powered games work? Is this essentially a form of DRM (Digital Rights Management)? Can I trust this software platform? Has anybody done any independent verification on how this platform works? (I'm very leery of any DRM after the Sony BMG CD copy protection scandal. Thank goodness for Mark Russinovich.) Does the "Steam" platform install anything particularly nasty or unwanted on my computer?

  Read the article

• Merge changes in Microsoft Word documents

  - by Álvaro G. Vicario

  I'm using Microsoft Word 2002 to maintain some documentation. The documents are stored in a version control repository (Subversion) together with the source code it documents. My Subversion client (TortoiseSVN) comes with a little VBA script that allows to leverage the built-in revisions feature when merging different branches. In other words, when I want to copy changes from one document to another, Word compares both documents (source and target) and builds a third document that has the contents of the source doc tagged as revisions, so I can then review differences one by one and confirm or discard changes. While this is handy, it also means that making a single change to the source document forces me to review all the differences between both documents and discard all of them except the only actual change. My questions is... Do you know about an application or plug-in that's able to find the differences between two Word documents and apply those differences to a third document? (I know 2002 is very old but that's what my company gives me; I'm open to solutions that use newer versions though.)

  Read the article

< Previous Page | 493 494 495 496 497 498 499 500 501 502 503 504  | Next Page >