Search Results

Search found 16914 results on 677 pages for 'single threaded'.

Page 493/677 | < Previous Page | 489 490 491 492 493 494 495 496 497 498 499 500  | Next Page >

• Exchange 2010 POP3/IMAP4/Transport services complaining that they can't find SSL certificate after blue screen

  - by Graeme Donaldson

  We have a single-server Exchange 2010 setup. In the early hours of this morning the server had a blue screen and rebooted. After coming back up the POP3/IMAP4 and Transport services are complaining that they cannot find the correct SSL certificate for mail.example.com. POP3: Log Name: Application Source: MSExchangePOP3 Date: 2012/04/23 11:45:15 AM Event ID: 2007 Task Category: (1) Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: A certificate for the host name "mail.example.com" couldn't be found. SSL or TLS encryption can't be made to the POP3 service. IMAP4: Log Name: Application Source: MSExchangeIMAP4 Date: 2012/04/23 08:30:44 AM Event ID: 2007 Task Category: (1) Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: A certificate for the host name "mail.example.com" couldn't be found. Neither SSL or TLS encryption can be made to the IMAP service. Transport: Log Name: Application Source: MSExchangeTransport Date: 2012/04/23 08:32:27 AM Event ID: 12014 Task Category: TransportService Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: Microsoft Exchange could not find a certificate that contains the domain name mail.example.com in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector Default EXCH01 with a FQDN parameter of mail.example.com. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. The odd part is that Get-ExchangeCertificate show the cert as enabled for all the relevant services, and OWA is working flawlessly using this certificate. [PS] C:\Users\graeme\Desktop>Get-ExchangeCertificate Thumbprint Services Subject ---------- -------- ------- XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX ....S. CN=exch01 YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY ....S. CN=exch01 ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ IP.WS. CN=mail.example.com, OU=Domain Control Validated, O=mail.exa... Here's the certificate in the computer account's personal cert store: Does anyone have any pointers for getting POP3/IMAP4/SMTP to use the cert again?

  Read the article

• Run command remotely on Windows computer

  - by Bilal Aslam

  I have a Windows Server 2008 instance on Amazon EC2 (Amazon's cloud compute platform, which provides VMs in the cloud). It has an external IP, and I have an admin account on the box. I would like to 'bootstrap' this instance remotely i.e. I want to run commands to download, install and configure apps on it, all without having to log on even once. Also, I cannot use psexec on the source computer. I have figured out how to do this to a remote, domain-joined computer using WMI. However, I have NOT been able to do for a remote computer on EC2. Here are some specific restrictions: The remote computer is not part of my domain, hence no Kerberos The remote computer does not have a cert I trust, or vice versa I am sure I am running into to some auth/trust restriction. Is there any way I can run a single command on the remote, given that I have admin privileges? I'm not tied down to using WMI, but I do need to run a command somehow. Feels like this should be a solved problem.

  Read the article

• Flushing iptables broke my pipe, how can I save my instance?

  - by Niels

  I was setting up my iptables when I performed a iptables -F and my ssh pipe broke. This is the last output of my session: root@alfapaints:~# iptables -L Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW,ESTABLISHED tcp dpt:2222 ACCEPT tcp -- li465-68.members.linode.com anywhere state NEW,ESTABLISHED tcp dpt:nrpe ACCEPT tcp -- anywhere anywhere tcp dpt:9200 state NEW,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:http state NEW,ESTABLISHED ACCEPT udp -- anywhere anywhere udp spt:domain Chain FORWARD (policy DROP) target prot opt source destination Chain OUTPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state ESTABLISHED tcp spt:2222 ACCEPT tcp -- anywhere anywhere state ESTABLISHED tcp spt:nrpe ACCEPT tcp -- anywhere anywhere tcp spt:9200 state ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp spt:http state ESTABLISHED ACCEPT udp -- anywhere anywhere udp dpt:domain root@alfapaints:~# iptables -F Write failed: Broken pipe I tested my connection just before and I was able to connect with ssh. Now I did a nmap scan and not a single port is open anymore. I know my VPS is running on VMWare ESXi, could a reboot help? Or if not could I attach and mount the disk to another vm to save the data? Does anybody have some advise? And maybe an explanation what happend or what could have cause my pipe to break? ps: I didn't save my rules on the config directories of iptables. But used a file I stored in ~/rules.config to apply my rules like this: iptables-restore < rules.config So probably a reboot would help? Thanks a lot in advance.

  Read the article

• java max heap size, how much is too much

  - by brad

  I'm having issues with a JRuby (rails) app running in tomcat. Occasionally page requests can take up to a minute to return (even though the rails logs processed the request in seconds so it's obviously a tomcat issue). I'm wondering what settings are optimal for the java heap size. I know there's no definitive answer, but I thought maybe someone could comment on my setup. I'm on a small EC2 instance which has 1.7g ram. I have the following JAVA_OPTS: -Xmx1536m -Xms256m -XX:MaxPermSize=256m -XX:+CMSClassUnloadingEnabled My first thought is that Xmx is too high. If I only have 1.7gb and I allocated 1.5gb to java, i feel like I'll get a lot of paging. Typically my java process shows (in top) 1.1g res memory and 2g virtual. I also read somewhere that setting the Xms and Xmx to the same size will help as it eliminates time spend on memory allocation. I'm not a java person but I've been tasked with figuring out this problem and I'm trying to find out where to start. Any tips are greatly appreciated!! update I've started analyzing the garbage collection dumps using -XX:+PrintGCDetails When i notice these occasional long load times, the gc logs go nuts. the last one I did (which took 25s to complete) I had gc log lines such as: 1720.267: [GC 1720.267: [DefNew: 27712K->16K(31104K), 0.0068020 secs] 281792K->254096K(444112K), 0.0069440 secs] 1720.294: [GC 1720.294: [DefNew: 27728K->0K(31104K), 0.0343340 secs] 281808K->254080K(444112K), 0.0344910 secs] about 300 of them on a single request!!! Now, I don't totally understand why it's always GC'ng from ~28m down to 0 over and over.

  Read the article

• uWSGI cannot find "application" using Flask and Virtualenv

  - by skyler

  Using uWSGI to serve a simple wsgi app, (a simple "Hello, World") my configuration works, but when I try to run a Flask app, I get this in uWSGI's error logs: current working directory: /opt/python-env/coefficient/lib/python2.6/site-packages writing pidfile to /var/run/uwsgi.pid detected binary path: /opt/uwsgi/uwsgi setuid() to 497 your memory page size is 4096 bytes detected max file descriptor number: 1024 lock engine: pthread robust mutexes uwsgi socket 0 bound to TCP address 127.0.0.1:3031 fd 3 Python version: 2.6.6 (r266:84292, Jun 18 2012, 14:18:47) [GCC 4.4.6 20110731 (Red Hat 4.4.6-3)] Set PythonHome to /opt/python-env/coefficient/ *** Python threads support is disabled. You can enable it with --enable-threads *** Python main interpreter initialized at 0xbed3b0 your server socket listen backlog is limited to 100 connections *** Operational MODE: single process *** added /opt/python-env/coefficient/lib/python2.6/site-packages/ to pythonpath. unable to find "application" callable in file /var/www/coefficient/flask.py unable to load app 0 (mountpoint='') (callable not found or import error) *** no app loaded. going in full dynamic mode *** *** uWSGI is running in multiple interpreter mode ***` Note in particular this part of the log: unable to find "application" callable in file /var/www/coefficient/flask.py unable to load app 0 (mountpoint='') (callable not found or import error) **no app loaded. going in full dynamic mode** This is my Flask app: from flask import Flask app = Flask(__name__) @app.route("/") def hello(): return "Hello, World, from Flask!" Before I added my Virtualenv's pythonpath to my configuration file, I was getting an ImportError for Flask. I solved this though, I believe (I'm not receiving errors about it anymore) and here is my complete configuration file: uwsgi: #socket: /tmp/uwsgi.sock socket: 127.0.0.1:3031 daemonize: /var/log/uwsgi.log pidfile: /var/run/uwsgi.pid master: true vacuum: true #wsgi-file: /var/www/coefficient/coefficient.py wsgi-file: /var/www/coefficient/flask.py processes: 1 virtualenv: /opt/python-env/coefficient/ pythonpath: /opt/python-env/coefficient/lib/python2.6/site-packages This is how I start uWSGI, from an rc script: /opt/uwsgi/uwsgi --yaml /etc/uwsgi/conf.yaml --uid uwsgi And if I try to view the Flask program in a browser, I get this: **uWSGI Error** Python application not found Any help is appreciated.

  Read the article

• Can't mount FAT32 drive under Ubuntu Linux

  - by Josh

  I have a 320GB USB drive with a single large FAT32 partition. The volume mounts perfectly fine on my Mac OS X 10.5.8 machine and Disk Utility on the mac reports no issues with the volume. I can read/write all data on the drive. However when I connect the drive to my Ubuntu 9.10 Karmic system, the partition does not mount. dmesg|tail says: [ 2752.334822] scsi3 : SCSI emulation for USB Mass Storage devices [ 2752.335040] usb-storage: device found at 3 [ 2752.335044] usb-storage: waiting for device to settle before scanning [ 2757.330301] usb-storage: device scan complete [ 2757.331005] scsi 3:0:0:0: Direct-Access WD 3200AAK External 1.65 PQ: 0 ANSI: 0 [ 2757.331772] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 2757.355647] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2757.360737] sd 3:0:0:0: [sdb] Write Protect is off [ 2757.360749] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 2757.360755] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367618] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367631] sdb: sdb1 [ 2762.797622] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2762.797636] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2822.866228] FAT: bogus number of reserved sectors [ 2822.866237] VFS: Can't find a valid FAT filesystem on dev sdb1. When I run fsck.vfat -a /dev/sdb1 I get: root@cartman:~# fsck.vfat -a /dev/sdb1 dosfsck 3.0.3, 18 May 2009, FAT32, LFN Logical sector size is zero. Googling "vfat Logical sector size is zero" produced no consensus as to the solution. I would prefer not to have to completely reformat the disk if possible because it contains about 280GB of data I would rather not have to find a temporary home for. Any suggestions?

  Read the article

• Websites down EC2 inaccessible via SSH CPU utilisation 100% last few hours - what should I do?

  - by fuzzybee

  I have multiple websites hosted on 1 single EC2 instance. 1 website "abc" were down for a few hours, sometimes threw database connection error and sometimes just took too long to respond. 1 website "def" were incredibly slow but still up and running the rest of the websites had the same symptoms has "abc" I can afford 15 min or less down time for "def". Should I then (in AWS console) reboot my instance or create an AMI image from my instance and launch it and associate my elastic IP to the new instance or "launch more like this" Background on what may have happened to my ec2 The last time I made changes for 21 hours ago. A cronjob to create snapshots ran around 19 hours ago and it has been running for a long time. Google Analytics shows traffic to my websites such as kidlander.sg has been nothing exceptional. Is there any other actions I should take or better options I could have? (I have already contacted AWS support but their turnaround is 12 hours so I appreciate all the help I could get) Update I got everything back up and running and CPU utilisation back to normal, around 30%. There is 1 difference between "def" and "abc" as well as my other websites "def"'s database is hosted on RDS "abc"'s database is hosted on an EC2 instance (different from my web server instance) configured by myself Nevertheless, I checked the EC2 instance I'm using as MySQL server yesterday and it was absolutely fine during the incident low CPU ultilisation I could log in using linux command line

  Read the article

• Extract archive here, autodetect subfolder

  - by lorancou

  I use 7-Zip under Windows 7 to extract all kind of archives. The ever-running problem is that there is not a single way to handle subfolders. Some people create their archives like this (let's call it type A): . +-- subfolder ¦   +-- file 1 ¦   +-- file 2 ¦   +-- ... "Extract Here" will extract everything to subfolder/, which is fine; "Extract to <Folder>" will create an extra subfolder level, which is annoying. And other people create them like that (let's call it type B): . +-- file1 +-- file 2 +-- ... "Extract Here" will populate the current folder, which can bring a lot of mess if this folder already contains tons of other files, and which is very annoying; "Extract to <Folder>" will create a subfolder and conveniently stuff it with the archive content, which is fine. So this leaves two options: always choose to "Extract to <Folder>" and live with the extra subfolder for type A archives. Or open the archive before extracting it to check if this is a type A or B, and then appropriately select "Extract Here" or "Extract to <Folder>". I usually do the latter, but I just discovered that KDE is offering a very handy Extract Archive Here, Autodetect Subfolder feature that automates that. It'll "Extract Here" if there's only one subfolder in the archive, otherwise it'll "Extract to <Folder>". I love this idea. Is there a Windows 7 tool offering this option? Preferably integrated in the explorer context menu? Maybe it's hidden somewhere in 7-Zip and I just didn't find it?

  Read the article

• Pitfalls to using Gluster as a home/profile directory server?

  - by Bart Silverstrim

  I was asking recently about options for divvying up access to file servers, as we have a NAS solution that gets fairly bogged down when our users (with giant profiles, especially) all log in nearly simultaneously. I ran across Gluster and it looks like it can cluster different physical storage media into a single virtual volume and share it out like a virtual NAS from the client perspective and it support CIFS. My question is whether something like this would be feasible to use for home and profile directories in an active directory environment. I was worried about ACL's, primarily, as I didn't think CIFS was fine-grained enough to support NTFS permissions and it didn't look like Gluster exports those permission levels, just the base permissions for basic file sharing. I got the impression that using Gluster would allow for data to be redundant across multiple servers and would speed up access to the files under heavy load, while allowing us to dynamically boost storage capacity by just adding another server and telling Gluster's master node to add that server. Maybe I'm wrong with my understanding of it though. Anyone else use it or care to share how feasible this is?

  Read the article

• File download speed issue over a dedicated fibre link

  - by nixnotwin

  My ISP has installed a fibre based dedicated internet connection at the place where I work. In the beginning the connection terminated at one of the ISP's core routers. It resulted in a strange issue. Eventhough the assigned speed was 5mbps, when tests were done by downloading large files over http and ftp from multiple locations, the speed never went above 2mbps. But bittorrent downloads reached 5mbps. Even file download from the ISP servers were fine. So, at the ISP our link was attached directly to their edge router. After this file downloads from high bandwidth servers, like Google and MS, reached the 5 mbps limit. Sometimes the speed would fall down below 2 mbps and suddenly it will go up to the 5 mbps limit ( it keeps on happening during any single file download). But other downloads like ubuntu apt repositories still struggle to go above 2 mbps. The engineers at the ISP have not been able to sort out the issue. After they moved us to their edge router instead of giving us 8 public ip's, they just gave 4 ip's. When we enquired about it, they told us that giving more ip's would result in arp overload at their edge router. But somehow I was able to convince them to give us the 8 ip's which we wanted. But the file download issue has remained. What might be the reason for files from different location getting downloaded with different speeds, that too with heavy fluctuation in speeds? I have downloaded files from same url's from a connection belonging to another smaller ISP, and the speeds were fine and reached full 5 mbps limit.

  Read the article

• Returning a 404 page when a folder is accessed from one domain, but allowing access from other domains and IP addresses

  - by okw

  Situation: I want to return a 404 page ("404.php") when a folder ("hidden") is accessed from the example.com domain. I want the same folder to be accessible from a subdomain ("hidden.example.com") or from a different domain ("hidden.com") which are both configured in a single VirtualHost entry. The server has multiple IP addresses that it listens on. Each IP address serves identical content from the example.com domain (sharing a VirtualHost entry.) I want the folder to be accessible from the IP address. The server is configured to use SSL/TLS/HTTPS. HTTPS is optional on example.com, but HTTPS is enforced in the .htaccess file for the hidden folder using a rewrite rule shown below. /www/hidden/.htaccess RewriteCond %{HTTPS} !=on RewriteRule .* https://%{SERVER_NAME}%{REQUEST_URI} [R,L] I know that {SERVER_ADDR} gives the server's IP address, but does it return the one that the client is requesting from? I'm also starting to think that something in the VirtualHosts file would be more appropriate. Any thoughts on this? What should be allowed: http://87.65.43.21/hidden/ https://87.65.43.21/hidden/ http://12.34.56.78/hidden/ https://12.34.56.78/hidden/ http://hidden.example.com/ https://hidden.example.com/ http://hidden.com/ https://hidden.com/ http://www.hidden.com/ https://www.hidden.com/ What should be 404-ed with 404.php http://example.com/hidden/ https://example.com/hidden/ http://www.example.com/hidden/ https://www.example.com/hidden/ http://example.com/hidden/hiddenfile.php https://example.com/hidden/hiddenfile.php etc. Thanks.

  Read the article

• MySQL Master-Master w/ multiple read slave cost effective setup in AWS

  - by Ross

  I've been evaluating Amazon Web Services RDS for MySQL and costing out potential scenarios involving a simple multi-AZ deployment read/write setup vs. a multi-AZ deployment mysql master (hot-standby) with additional read-only slaves. the issue I'm trying to cost-optimize includes their reserved instance vs on-demand instances. Situation 1: purchase reserved multi-az setup for Extra-large-hi-mem(17GB RAM) instance for $5200/yr and have my application query the master all the time. the problem is, if I don't need all the resources of the (17GB RAM) all the time and therefore, especially not a hot-standby, what alternatives for savings can a better topology create, like potentially situation 2 below: Situation 2: purchase reserved multi-az setup using smaller master instances than above for the master-master hot-standby to receive the writes only. Then create and load balance several read-only slaves off the master and add/remove and/or scale up/down the read slaves based on demand. This might only cost $1000 + the on-demand usage of the read slaves. My thinking is, if I have a variable read-intensive application load, with low write load, the single level topology in situation 1 means I'm paying for a lot of resources at the write level of topology when I don't need them there. My hope is that situation 2 can yield cost savings from smaller reserved instances on the master-master resource level allowing me to scale up and down and/or out on the read-level according to demand as needed. Does anyone see a downside to doing this or know of some reason this isn't possible with RDS? Any other thoughts or advice always welcome of course. Thanks in advance, R

  Read the article

• Will adding a SSD cache device to my ZFS storage improve performance?

  - by Sysadminicus

  The server has 4GB of RAM and my zpool is made up of 15.5k SAS drives arranged like this: NAME STATE READ WRITE CKSUM tank ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c0t2d0 ONLINE 0 0 0 c0t3d0 ONLINE 0 0 0 c0t4d0 ONLINE 0 0 0 c0t5d0 ONLINE 0 0 0 c0t6d0 ONLINE 0 0 0 c0t7d0 ONLINE 0 0 0 c0t8d0 ONLINE 0 0 0 raidz1-1 ONLINE 0 0 0 c0t10d0 ONLINE 0 0 0 c0t11d0 ONLINE 0 0 0 c0t12d0 ONLINE 0 0 0 c0t13d0 ONLINE 0 0 0 c0t14d0 ONLINE 0 0 0 spares c0t9d0 AVAIL c0t1d0 AVAIL The primary use is as an NFS store for a couple VMWare ESXi servers. I can't do any "true" benchmarks because this is a production system (no budget for test systems), but using dd and bonnie++ I can't get more than ~40-50MB/s writes and ~70-90MB/s reads. It seems I should be able to do much better, but I'm not sure where to optimize. Based on what I've read, I think dropping in a OCZ Vertex 2 Pro SSD as my L2ARC is going to be the best bang-for-the-buck to improve througput. Is there something else I should be looking into to help performance? If not... How do I know how big a cache device I need? Am I safe with only a single SSD as my cache device?

  Read the article

• Using native resolution on external display results in stretched, out of bounds image

  - by Roni Yaniv

  I have an HP min 311 netbook with Windows XP, which I've connected to a Samsung SyncMaster 2043BW display via the supplied analog cable. The external display's native res is 1680x1050, which the netbook's ION GPU supports. I've configured the external display as the single display (no cloning or any such fancy stuff). However, once I set the native res, the image just stretches out. It looks squashed, and it goes outside the monitor's edges. In contrast, lower resolutions manage to stay within the monitor's display edges, though obviously they are skewed in some way (vertically or horizontally). BTW, the only res which seems to be displayed relatively clearly (it's the least blurry) is 1280x720. I tried looking all over the web for an explanation/advice but could not find any. I already played with the settings on the external display itself several times. So either it's not that, or I missed something. Has someone run into this issue? I need help.

  Read the article

• Laptop authentication/logon via accelerometer tilt, flip, and twist

  - by wonsungi

  Looking for another application/technology: A number of years ago, I read about a novel way to authenticate and log on to a laptop. The user simply had to hold the laptop in the air and execute a simple series of tilts and flips to the laptop. By logging accelerometer data, this creates a unique signature for the user. Even if an attacker watched and repeated the exact same motions, the attacker could not replicate the user's movements closely enough. I am looking for information about this technology again, but I can't find anything. It may have been an actual feature on a laptop, or it may have just been a research project. I think I read about it in a magazine like Wired. Does anyone have more information about authentication via unique accelerometer signatures? Here are the closest articles I have been able to find: Knock-based commands for your Linux laptop Shake Well Before Use: Authentication Based on Accelerometer Data[PDF] Inferring Identity using Accelerometers in Television Remote Controls User Evaluation of Lightweight User Authentication with a Single Tri-Axis Accelerometer Identifying Users of Portable Devices from Gait Pattern with Accelerometers[PDF] 3D Signature Biometrics Using Curvature Moments[PDF] MoViSign: A novel authentication mechanism using mobile virtual signatures

  Read the article

• OpenSSL: how to setup an OCSP server for checking third-party certificates?

  - by StackedCrooked

  I am testing the Certificate Revocation functionality of a CMTS device. This requires me to setup a OCSP responder. Since it will only be used for testing I assume that the minimal implementation provided by OpenSSL should suffice. I have extracted the a certificate from a cable modem, copied it to my PC and converted it to the PEM format. Now I want to register it in the OpenSSL OCSP database and start a server. I have completed all these steps, but when I do a client request my server invariably responds with "unknown". It seems to be completely unaware of my certificate's existence. I would greatly appreciate if anyone would be willing to have a look at my code. For your convenience, I have created a single script consisting of a sequential list of all used commands, from setting up the CA until starting the server: http://code.google.com/p/stacked-crooked/source/browse/trunk/Misc/OpenSSL/AllCommands.sh You can also find the custom config file and the certificate that I am testing with: http://code.google.com/p/stacked-crooked/source/browse/trunk/Misc/OpenSSL/ Any help would be greatly appreciated.

  Read the article

• OpenSSL: how to setup an OCSP server for checking third-party certificates?

  - by StackedCrooked

  I am testing the Certificate Revocation functionality of a CMTS device. This requires me to setup a OCSP responder. Since it will only be used for testing I assume that the minimal implementation provided by OpenSSL should suffice. I have extracted the a certificate from a cable modem, copied it to my PC and converted it to the PEM format. Now I want to register it in the OpenSSL OCSP database and start a server. I have completed all these steps, but when I do a client request my server invariably responds with "unknown". It seems to be completely unaware of my certificate's existence. I would greatly appreciate if anyone would be willing to have a look at my code. For your convenience, I have created a single script consisting of a sequential list of all used commands, from setting up the CA until starting the server: http://code.google.com/p/stacked-crooked/source/browse/trunk/Misc/OpenSSL/AllCommands.sh You can also find the custom config file and the certificate that I am testing with: http://code.google.com/p/stacked-crooked/source/browse/trunk/Misc/OpenSSL/ Any help would be greatly appreciated.

  Read the article

• Conky starts above windows in Ubuntu Maverick

  - by DesertIvy

  Hey guys, I did not run into this problem until I upgraded my Ubuntu box to Maverick Meerkat (10.10). Basically, whenever I start my computer, conky runs as expected, except it gets drawn over any windows that I load (see screenshot). To fix this for a single session, I simply restart conky by running killall conky; conky in a terminal. Conky gets re-drawn below active windows (namely, only appearing on my desktop), and does not have the border/drop-shadow, but I have to do this every time I start a new session. Is there a simple way to fix this? I have a small shell script that I run on startup, but it does not seem to solve the problem. #!/bin/bash sleep 10 && conky; sleep 5 && killall conky; conky; Below is the non-text part of my .conkyrc file. # Conky settings # background yes update_interval 1 cpu_avg_samples 2 net_avg_samples 2 override_utf8_locale yes double_buffer yes no_buffers yes text_buffer_size 2048 #imlib_cache_size 0 temperature_unit fahrenheit # Window specifications # own_window yes own_window_type override own_window_transparent yes own_window_hints undecorate,sticky,skip_taskbar,skip_pager,below border_inner_margin 0 border_outer_margin 0 minimum_size 200 250 maximum_width 200 alignment tr gap_x 220 gap_y 280 # Graphics settings # draw_shades no draw_outline no draw_borders no draw_graph_borders no # Text settings # use_xft yes xftfont caviar dreams:size=8 xftalpha 0.5 uppercase no temperature_unit celsius default_color FFFFFF # Lua Load # lua_load ~/.lua/scripts/clock_rings.lua lua_draw_hook_pre clock_rings

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

• Can I have 2Gbit over 1Gbit Nics

  - by Daniel

  So this really baffles me. Apparently because 1Gbit can transmit data in both directions simultaneously it should be possible to get 2Gbit of data transfer on a single NIC (1Gbit flow seend and 1Gbit receive). People claim that because 1Gbit is full-duplex (almost always) it is exactly 2Gbit in total. My intuition and electrical background tells me that something is not right here 4 twisted pairs 250Mbit capacity each gives 1Gbit. Unless it is really possible to transfer data in both directions simultaneously. I did a test with iperf. Ubuntu server 12.04 <-- MacBook Pro. Both with decent CPU speed. Tested speed of connection individually and on Mac I can see 112MB/s regardless which direction data is going. On Ubuntu with vnstat and ifstat I got 970Mbit speeds. Now, launching iperf in server mode on both machines at the same time and sending data using 2 iperf clients shows that I'm for example on Ubuntu box sending at 600Mbit, and receiving 350Mbit. which adds up to pretty much 1Gbit link. So to me there is no magical 2Gbit. Can someone confirm that or tell why I'm wrong? Another thing that confuses me i the fact that e.g. 24-port switch has for example: Throughput»up»to:»50.6Mpps Switching»capacity:»68Gbps Switch»fabric»speed:»88Gbps Which would suggest thay can handle 2GBit per port.

  Read the article

• Which server software and configuration to retrieve from multiple POP servers, routing by address to correct user

  - by rolinger

  I am setting up a small email server on a Debian machine, which needs to pick up mail from a variety of POP servers and figure out who to send it to from the address, but I'm not clear what software will do what I need, although it seems like a very simple question! For example, I have 2 users, Alice and Bob. Any email to [email protected] ([email protected] etc) should go to Alice, all other mail to domain.example.com should go to Bob. Any email to [email protected] should go to Bob, and [email protected] should go to Alice Anything to *@bobs.place.com should go to Bob And so on... The idea is to pull together a load of mail addresses that have built up over the years and present them all as a single mailbox for Bob and another one for Alice. I'm expecting something like Postfix + Dovecot + Amavis + Spamassassin + Squirrelmail to fit the bill, but I'm not sure where the above comes in, can Postfix deal with it as a set of defined regular expressions, or is it a job for Amavis, or something else entirely? Do I need fetchmail in this mix, or is its role now included in one of the other components above. I think of it as content-filtering, but everything I read about content-filtering is focussed on detecting spam rather than routing email.

  Read the article

• How much does a computer actually cost?

  - by Cawas

  Ok, so when you buy a new notebook, you spend about $1 or $2 thousand with the OS included. When you make your own desktop machine you can get as low as $100 for a good one today, with not a single piece of software included. It can't be much lower, but it can go lot higher. People, including myself, tend to believe that's the price of a computer, but then there comes the softwares. I just stumbled upon a nice piece of application I could use myself, but it's very specific, very tiny, and most people would never bother about this. And it costs "just $12". That is a lot for something I may use just once or twice! OS upgrades, hardware malfunction, and your custom set of software actually raise the computer price quite a lot, thus this question: how much we pay in the end for our personal computers? I'd like to see some statistics on that. Maybe divided into 3 categories or something, but some data with averages, minimum and "maximum" costs would be very nice. Maybe a "cost per year" would be nice. Just wondering.

  Read the article

• Apache2 process stuck at 100% cpu, CLOSE_WAIT socket lingering

  - by mmazing

  I've troubleshooted the heck out of this today, and I can't seem to find any information on how to determine what is happening exactly. Basically, on my development server, another developer is causing CLOSE_WAIT connections that eat up one or more apache2 processes for several hours if I don't restart apache2. strace on any of the processes yields no information, only that it was able to attach. mod_proxy is not enabled. KeepAlive is on, KeepAliveTimeout is 15 seconds, MaxKeepAliveRequests is 100. From what I've been reading, this may or may not be an apache issue at all, just that that's how CLOSE_WAIT works (the server is waiting for a FIN packet to close the connection). I just can't believe that a server would be crippled so easily by not receiving a packet from a remote host telling it to close the connection. Especially without any intervention for well over an hour. Any tips? I'm about to pull my hair out. Edit : Also, there are no unusual entries in any apache log files. Edit 2: lsof -i shows only a single CLOSE_WAIT per hanging process. (That's what has been bothering me about this, as most other discussions talk about many CLOSE_WAIT connections, while I only have one per process.) The nature of the code that is running (php) doesn't really lend itself to closing open connections and whatnot. I can run the same code that he is executing with the same session data, and not result in a hanging process.

  Read the article

• TV-out worked, now doesn't. May the problem be the cable, TV, driver, OS, graphic card?

  - by Petruza

  I have a CRT TV hooked to the PC, which once worked great, now doesn't. I can't consider getting a newer TV, this one is used in an MAME arcade cabinet so it has to be a CRT for best old school look and feel. It's connected through the TV-out connector of my graphic card. When it worked, I had Windows XP, the same PC and the same card. Now I have windows 7, not sure if the OS switch caused the malfunction as I don't use the TV-out all the time. Can it be an upgrade of the Nvidia driver? I thought it may be the S-video to RCA cable, but tried 3 different cables and neither worked. In fact, one of them, that unlike the other two, has a single RCA output connector instead of two, behaves differently, although it doesn't work, but it does the following: When I open the NVidia settings panel, or when I change a setting and click Apply then the TV flashes for a split second and you can see the windows screen, but then it goes back to blank. So any clues what can be failing here, and some advice? Possible failures, please comment on the one you suspect the most: NVidia driver version Windows version Cable Graphic card's TV out other?

  Read the article

• Make a snapshot of a live mySQL database with myISAM & innoDB tables without locking

  - by Artem

  We have a live database in production where we are running out of space on the server. So I would like to transfer to a new server without any downtime (or as little downtime as possible). In general, I would also like to have a hot failover copy of the database available. I would like to use replication to get all of the data copied to the new machine, and then at some point flip a switch and have that new machine become the master (normal failover scenario). My problem is that I am not sure how to initialize replication without locking the db to make the initial snapshot I will use? Is there any way to do this? I know I could do it using single-transaction if I was using innoDB, but very unfortunately we have some myISAM tables in there (in fact the largest 150GB table is myISAM and I want to switch it to InnoDB but I can't do it until I have more space & a hot copy to switch to). Any ideas? Is there some way to make such a snapshot? Or is there alternatively a way to get replication to "catch up" without an snapshot for initialization?

  Read the article

< Previous Page | 489 490 491 492 493 494 495 496 497 498 499 500  | Next Page >