Search Results

Search found 27238 results on 1090 pages for 'local variable'.

Page 505/1090 | < Previous Page | 501 502 503 504 505 506 507 508 509 510 511 512  | Next Page >

  • Windows 7 Ultimate Restore From Another Machine

    - by Guy Thomas
    The situation I have an old machine running Windows Server 2008. I make a backup of selected directories. New Machine: I install Windows 7 Ultimate (and Windows Server 2008 [dual boot]) I cannot restore those files that I backed-up on the old machine. On the New machine neither the Windows 7 or Windows Server 2008 Restore (Recovery) can 'see' the backup files even though they are on the local machine. Is this behaviour (non-behaviour) 'by design' or am I missing something?

    Read the article

  • Why apcupsd won't see the UPS connected to the USB posrt on FreeBSD 8.0 amd64

    - by Max Kosyakov
    Hello, Recently I installed an apcusbd on a FreeBSD 8.0 amd64 box via ports system. It installed perfectly but it won't run. Here what is says in the log: FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device It appeared that HID driver picked the /dev/ugen4.2 which could cause the apcusb being unable to find the device. After I had discovered this, I rebuilt the kernel and removed the hid driver. Now it just shows "ugen4.2: <Tripp Lite> at usbus4" and no uhid0 device appears. Nevertheless the problem persisted. I tried to leave the DEVICE config setting blank --- won't help. Then I specified the particular device in the config, but it did not help either. Below you is the output of several commands that can provide some useful information on my case. server# /usr/local/etc/rc.d/apcupsd start Starting apcupsd. server# tail /var/log/messages | grep apcupsd Jun 17 22:30:00 server apcupsd[1520]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see . Jun 17 22:30:00 server apcupsd[1520]: apcupsd error shutdown completed server# cat /usr/local/etc/apcupsd/apcupsd.conf ## apcupsd.conf v1.1 ## UPSCABLE usb UPSTYPE usb DEVICE /dev/ugen4.2 LOCKFILE /var/lock UPSCLASS standalone UPSMODE disable server# dmesg | grep '^u' uhci0: port 0xa800-0xa81f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f00 usbus0: on uhci0 uhci1: port 0xa880-0xa89f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f00 usbus1: on uhci1 uhci2: port 0xac00-0xac1f irq 18 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f00 usbus2: on uhci2 usbus3: EHCI version 1.0 usbus3: on ehci0 uhci3: port 0xa080-0xa09f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f00 usbus4: on uhci3 uhci4: port 0xa400-0xa41f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f00 usbus5: on uhci4 uhci5: port 0xa480-0xa49f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f00 usbus6: on uhci5 usbus7: EHCI version 1.0 usbus7: on ehci1 uart0: port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 ugen2.1: at usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3: on usbus3 ugen4.1: at usbus4 uhub4: on usbus4 ugen5.1: at usbus5 uhub5: on usbus5 ugen6.1: at usbus6 uhub6: on usbus6 ugen7.1: at usbus7 uhub7: on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered ugen4.2: at usbus4 server#

    Read the article

  • Google Chrome on Mac OS X, full screen option is greyed out, why?

    - by Chris Kimpton
    When I first installed Chrome the menu option for "full screen" was enabled and worked, but for the last few months is been greyed out/disabled. Is it just me or perhaps there is a bug which is why its disabled? I tried deleting the installed version and downloading a new copy, to no avail - but perhaps there is a setting in my local preferences that could be disabling it. Thanks in advance, Chris

    Read the article

  • OpenVPN/Tunnelblick through wireless router, no connection.

    - by Oscar
    I'm using OpenVPN with Tunneblick on my Macbook Pro to access a server on my job. I't works fine, but i can't get it working with my Netgear WGT624v3 wireless router. I get this warning: WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] Someone told me that i should "port forward" on my router, but i can't figure out the right settings. Also not shure i'm doing it right.

    Read the article

  • Ineractive logon message doesn't show?

    - by user19049
    We set the Group Policy for our Domain and OUs to show the logon message: Computer Configuration\Windows Settings\Security Settings\Local Policies\Security Options\ Interactive logon: Message text for users attempting to log on but nothing happen when the client computer logon. I checked the RSOP.MSC to see the group policy that set and the message is set on client computer but it doesn't show at the logon prompt. so what should I do? We have Windows server 2003 AD and Windows XP Pro on client computer.

    Read the article

  • Start multiple Firefoxes; Xephyr rootless mode

    - by Vi
    How to have multiple independent instances of Mozilla Firefox 3.5 on the same X server, but started from different user accounts (consequently, different profiles)? Limited success was only with Xephyr :1, DISPLAY=:1 /usr/local/bin/firefox, but Xephyr has no Cygwin/X's "rootless" mode so it not comfortable. The idea is to have one Firefox instance for various "Serious Business" things and the other for regular browsing with dozens of add-ons securely isolated. /* Requested tags: xephyr rootless */

    Read the article

  • Sent items listed by sender's name (my name!) not recipient in Outlook for Mac 2011

    - by user568458
    Outlook 2011 on a Mac (OSX7 Lion), on a (mostly PC) office network using Microsoft Exchange server. In Outlook 2011, in the network "Sent Items" folder, all emails are listed showing the sender's name (my name), not the recipients' names. That means every single email is headed with my own name, like this: My Name 08/09/2012 Some subject line [flag] My Name 08/09/2012 Re: Another subject line [flag] My Name 07/09/2012 Re: different subject line [flag] My Name 07/09/2012 different subject line [flag] ...and so on. There's no clue at all as to who these emails were to, until I open each and every one. I guess it's reassuring to be told that every email that I sent was sent by me... and if I was ever to forget my own name while browsing my sent emails folder, it'd be super useful... But it's not very helpful for navigating sent emails. Is this normal for Office for Mac 2011? How can I fix this, so that the list shows the recipients' names instead of endlessly reminding me of my own name? Things I've found while researching this: This can also happen in Outlook for Windows. On Windows, it's easily fixed by resetting the field. That method doesn't work on Mac because the fields can't be selected separately. It seems this can also happen in Apple Mail too, and a lot of people seem stumped by this. I can't find anything on this specific to Outlook 2011 or Outlook for Mac in general. A simple guide on how to fix this would be the best answer, but I'd also welcome any knowledgable thoughts from Microsoft Exchange Server people on whether this sounds like an Outlook settings issue which I can fix on my machine, or some issue relating to how the Mac gets data from the server and network. The fact that Apple Mail users have encountered the same issue with no apparent fix makes me think the problem might be in the network rather than the mail client - but that's way beyond my limited knowledge of these things. I don't know whether the local ("On my computer") Sent Items folder has the same problem, as it's configured so that no emails except drafts are ever stored in these local folders. Drafts saved locally are listed by recipient as expected.

    Read the article

  • Is my Cisco switch port bad?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • How to change suexec root directory from "/var/www" to "/home"?

    - by Oudin
    Hi I've installed suexec using on ubuntu 12.04: apt-get install apache2 apache2-suexec libapache2-mod-fcgid php5-cgi However when I run the following command: sudo /usr/lib/apache2/suexec -V I get the following info: -D AP_DOC_ROOT="/var/www" -D AP_GID_MIN=100 -D AP_HTTPD_USER="www-data" -D AP_LOG_EXEC="/var/log/apache2/suexec.log" -D AP_SAFE_PATH="/usr/local/bin:/usr/bin:/bin" -D AP_UID_MIN=100 -D AP_USERDIR_SUFFIX="public_html" I'm utilizing "/home/user/public_html" to serve users content on the web not "/var/www" How can I change the root directory to "/home"?

    Read the article

  • How do I uninstall mysql on snow leopard osx?

    - by Abhic
    Hello I had installed mysql from the command line when I setup a local web server with custom modules on my snow leopard box. I recently discovered MAMP and its just easier to work with it than with the personal web server Apple has and via command like utils. I uninstall ports completely but still see 'mysqld' in my Activity Monitor. I would like to uninstall this cleanly. Any tips? Thank you.

    Read the article

  • How to tell credentials used for a Network Mapping?

    - by shanecourtrille
    I have a networking mapping that doesn't appear to work. When I connect to the mapping I get access denied when I try to create a folder. When I created the mapping I told it to login as another account. I have verified that account has the proper rights on the server side of things. How can I verify that my local machine is connecting with the right credentials?

    Read the article

  • Exchange 2003 default permissions for ANONYMOUS LOGON and Everyone

    - by Make it useful Keep it simple
    ANONYMOUS LOGON and Everyone have the following top level permissions in our Exchange 2003 Server: Read Execute Read permissions List contents Read properties List objects Create public folder Create named properties in the information store Are these the "default" settings? In particular, are the "Read" and "Execute" permissions a problem? We have a simple small business setup, Outlook clients connect to the server on the local network, OWA is used from outside the network for browser and smartphone access. Thanks

    Read the article

  • Could not evaluate: certificate verify failed while using ssl proxy

    - by Onitlikesonic
    One of our machines was recently put behind an SSL proxy and since then I can't connect to puppet with "Could not evaluate: certificate verify failed." I have checked that the dates match, regenerated the certificates but to no avail. Debugging the verification with "openssl s_client -showcerts -connect puppetmaster:puppetmasterport" shows "Verify return code: 0 (ok)" Initially the Proxy SSL Certificate was not recognized with a "Verify return code: 20 (unable to get local issuer certificate)" problem which was then fixed with the answer in the question: Adding root certificate to CentOS 5

    Read the article

  • Powershell Remoting Handover Variables

    - by icnivad
    I've opened a Remote Session s1, and like to run a function with Parameters i handover in my scriptblock: Simplified example with Write-Host: $a = "aaa" $b = "bbb" $c = "ccc" $d = "ddd" Write-Host "AAAAA: $a $b $c $d" #This works fine as it's locally Invoke-Command -Session $s1 -scriptblock {Write-Host "BBBBB: $a $b $c $d"} #These variables are empty What is the cleanest way to handover Variables (I normally receive from a local csv file) to the scriptblock?

    Read the article

  • Best tools for "ssh tail -f" style log file monitoring and analysis

    - by dougnukem
    I'm looking for a tool to monitor custom PHP Error logs/Apache and possibly Java logs on remote development servers. I'm not looking for a full production log system like Splunk, but something that's a little more flexible than an ssh terminal doing a "tail -f". Perhaps something that will: * Monitor multiple log files to my local machine for searching/analysis later * Allow "alerts" when certain strings appear in the log * Provide some kind of tabbed/dashboard view of the multiple logs being monitored (in total less than 10 logs).

    Read the article

  • what is ranlib?

    - by Ying
    I have been using a MacOSX system for a while, but just only recently started poking into the guts. I found a guide telling me to run 'sudo ranlib /usr/local/lib/libjpeg.a'(installing libjpeg). I have read the ranlib manual, and tried looking online on it. I simply don't understand. What resources do I need to look up to learn more, or can someone give a concise explanation on its use? Thanks in advance!

    Read the article

  • Migrating from register.com webmail

    - by mgb
    Anyone know of any tools to migrate emails from register.com's webmail to anything else (gmail, local mbox, anything!), I have nearly 15 years of mails and folders I want to keep. Other than spending ages writing some Perl scraper code I wondered if anyone else had already done this. sorry - It's impossible to search Google for the name of a registrar!

    Read the article

  • Install Python 2.6 on Debian Unix

    - by Bialecki
    I want to install Python 2.6, but as it's still experimental for Debian Unix, I'm wondering what might best course of action is. Is the right idea to idea it into /usr/local for my system and then update the python sym link in /usr/bin to point to that version? Other considerations or ways to do it I should be thinking about?

    Read the article

  • Automounting AFP Share For OpenDirectory Users (Mac Lion Server)

    - by davzie
    We're moving all our Mac's from local logins to OpenDirectory logins in an effort to keep everything secure and to also solve issues we have with a Tiger server buggering permissions on an AFP shared drive. To cut it short, I want users to be able to login to their OpenDirectory account and I then want the AFP share point to mount using the credentials they just logged in with. Firstly, is this possible (I assumed it was) and secondly how might I go about doing it? Cheers, Dave

    Read the article

  • What user is the script run as after Carbon Copy Cloner ends scheduled task?

    - by Paolo
    On Mac OS X I keep data on a local server mirrored with the same data on a remote server with a scheduled backup task done with Carbon Copy Cloner. After the backup is done a bash script is run as specified in the scheduled task options of CCC. Is the script run as root? Or differently and more generally: as my script writes to a log file, what command should I put on my script to see on the log if the script is running as root or something else?

    Read the article

< Previous Page | 501 502 503 504 505 506 507 508 509 510 511 512  | Next Page >