Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 509/772 | < Previous Page | 505 506 507 508 509 510 511 512 513 514 515 516  | Next Page >

• needing storage integrity (write/read) test - for BASH

  - by Mr. Bash

  In need of shell scripts / bash commands to verify data integrity of local harddrives, usb-drives, etc, ... Like the famous www.heise.de/download/h2testw; or something that is at least common within repositories. (h2testw writes a specific datastring over and over onto the medium, then reads it again to verify if it was written correctly and displays write/read time/speed.) please no dd if=/dev/random of=/dev/sdx bs=1k && dd if=/dev/sdx of=/dev/null bs=1k since it won't verify if everything was written correctly. It is only a test if read/write is successful to the device. So far, I'm not too happy with badblocks -w -v /dev/sdx1 either, since it seems rather slow and I don't know what it exactly writes, and if it considers wear-leveling on flash media. There is also a program named F3 http://oss.digirati.com.br/f3/ that needs to be compiled. Designed after h2testw, the concept sounds interesting, i'd just rather have it as a ready to go bash script.

  Read the article

• Overriding routes on Openvpn client, iproute, iptables2

  - by sarvavijJana

  I am looking for some way to route packets based on its destination ports switching regular internet connection and established openvpn tunnel. This is my configuration OpenVPN server ( I have no control over it ) OpenVPN client running ubuntu wlan0 192.168.1.111 - internet connected if Several routes applied on connection to openvpn from server: /sbin/route add -net 207.126.92.3 netmask 255.255.255.255 gw 192.168.1.1 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 And I need to route packets regarding it's destination ports for ex: 80,443 into vpn everything else directly to isp connection 192.168.1.1 What i have used during my attempts: iptables -A OUTPUT -t mangle -p tcp -m multiport ! --dports 80,443 -j MARK --set-xmark 0x1/0xffffffff ip rule add fwmark 0x1 table 100 ip route add default via 192.168.1.1 table 100 I was trying to apply this settings using up/down options of openvpn client configuration All my attempts reduced to successful packet delivery and response only via vpn tunnel. Packets routed bypassing vpn i have used some SNAT to gain proper src address iptables -A POSTROUTING -t nat -o $IF -p tcp -m multiport --dports 80,443 -j SNAT --to $IF_IP failed in SYN-ACK like 0 0,1 0,1: "70","192.168.1.111","X.X.X.X","TCP","34314 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18664016 TSER=0 WS=7" "71","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584430 TSER=18654692 WS=5" "72","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584779 TSER=18654692 WS=5" "73","192.168.1.111","X.X.X.X","TCP","34343 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18673732 TSER=0 WS=7" I hope someone has already overcome such a situation or probably knows better approach to fulfill requirements. Please kindly give me a good advice or working solution.

  Read the article

• Load Testing a Security/Gateway Appliance

  - by Joel Coel

  In a couple weeks I will load testing a security/gateway appliance. We're a small residential college, and that "residential" means the traffic moving through the appliance is a bit like the Wild West. We have everything from Facebook to World of Warcraft, BitTorrent to Netflix, or Halo to YouTube... basically anything you might find in the home of a high-school or college aged person. Somewhere in there some real academic work gets done as well. We rely on our current appliance for traffic shaping, antivirus, malware filtering, intrusion detection on our servers, logging and abuse reporting, and even some content filtering. All this puts a decent load when we have students around, and I'm concerned about the ability of the new candidate to keep up. On paper it should handle things, but I'm worried. Prior experience is that vendors greatly over-report what an appliance can handle. The product also includes a licensed session limit, and I'm also worried that just a few misbehaving students could unwittingly bring us to that limit and cause service disruptions. I need to know this will work for our campus in order to commit to it. Going a performance level higher in that product takes the pricing way out of line with what we expect and have done in the past. What I need is a good way to load test this guy. My problem is that our current level of summer traffic is less than one percent of what it will be when students come back just six weeks from now. Any ideas on how to really stress this thing and see what it can do, in a way that will give me some clear ideas o. How that will scale for our campus? For the curious, I'm looking at a Watchguard 515, but it could be anything. If I were evaluating a competitor, I'd ask the same question.

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

• Windows 2008 RemoteAPP client disconnects within a matter of minutes.

  - by Jeroen Wilke

  I'm having an odd problem with Windows 2008 TS, and remote applications specifically. The situation is as follows: TS idle timeout is disabled via GPO TS terminating disconnected sessions after 1hr (via GPO) My users can log on to the Terminal server, and get a full desktop, OR via rdp files that give access to a few remote applications. When a user connects to a full desktop, everything is fine and dandy, they will remain logged on indefinately, and when they disconnect the session is terminated after an hour. however, when a user connects using a remote application link, the client seems to disconnect after only a few minutes of inactivity, when you click the window, the session reconnects. EventID's on TS server: 4779: This event is generated when a user disconnects from an existing Terminal Services session, or when a user switches away from an existing destop using Fast User Switching. 4778 : This event is generated when a user reconnects to an existing Terminal Services session, or when a user switches to an existing desktop using Fast User Switching users are connecting directly to 3389, not using a TS-gateway at the moment. This behavior is consistent on different clients that we have, Full desktop is fine, RemoteAPP constantly disconnects. The .rdp file used doesn't list any interesting parameters, aside from what application to launch, and where to find it. Can someone explain to me how there can be a difference in behaviour between full desktop, and remoteapp ? since essentially they use the exact same client ? Regards Jeroen

  Read the article

• Wordpress Directory Permission to allow uploads, plugin folders, etc

  - by user1015958

  I have a wordpress pre-made site which were developed on my localmachine, and i uploaded it too a vps running on debian6, using nginx, mysql, php. Following this guide: 1) Create an unprivilaged user, this could be say 'karl' or whatever, and make them belong to the www-data group. So that if I were to login as karl and create a web root in say /home/karl/www/ , all the files will be owned by karl:www-data 2) Set up nginx as the user www-data in nginx.conf 3) Set up PHP-FPM to run as www-data 4) Place your files in /home/karl/www/[domain name maybe]/public_html/, upload as 'karl' so you don't have to chown everything again. when i type ls -l inside public_html/ it shows that all the files inside are owned by karl:karl. But the public_html directory is owned by karl:www-data. I chmod 0755 the folder wp-content but i still get the error: ERROR: Path ../wp-content/connection_images does not seem to be writeable. I know i shouldn't set it too 777 due to security reason, how should i set it too proper permission? and what should i set also to allow my users to upload,write posts,edit articles? Sorry for my english by the way.

  Read the article

• NATing IPv4 while routing IPv6

  - by Hugo

  I've the following setup: client(s) <---> (eth0) router (eth1) <---> wan I have a static IPv4 address and a /48 IPv6 address block. I need to connect all the clients to (wan). Each client will have it's own public IPv6. Meanwhile, I need to NAT those same clients over to (wan). Everything IPv4-related and the NAT are working fine. The IPv6 communication to/from (eth0)<-(clients) works fine, as does the IPv6 communication from (eth1)<-(wan) works fine. To provide IPv6 to all my clients, I've thought of too choices: Having the router as a gateway, which different IP on each interface. This sounds like I need to tell my ISP to route the entire block through that single IP, so it's not really an option. Transparently pass IPv6 packets to/from eth0<-eth1, so all clients can communicate with the upstream gateway (I would actually have a switch here if it weren't for the need to remain IPv4 compatible). So, since I've opted for the second choice, I'm in doubt: How can I pass all IPv6 traffic from eth0 to eth1 transparently? What I need is a level 3 bridge, but linux's bridgeutils create a level 2 bridge (which would bridge ipv4 as well, and I can't have that). This is a DD-WRT device, but it's pretty much an embeded linux, so most suggestions that would work on linux are welcome. Thanks.

  Read the article

• Is it possible to setup an internal test email server to keep all mail sent to it?

  - by MattGrommes

  We have a need at my work to setup a test email server that will take all mail sent to it for delivery and instead just dump it into an account for later retrieval. I've been out of the email server configuration game long enough that I think that's possible but I don't know for sure. As a more specific example of what we need: We have code that sends emails to outside clients in certain cases. We want to point our code to a test server that will accept those emails, but not let them get to the outside world (yes, it's happened before, oops). We then need to be able to verify that Email X would have gotten sent to Client Y if we had sent to the real server. As a bonus, we have a error email alias on our real server that goes to the programmers that we would like to keep getting email from. So anything sent to that alias on the test server would forward to our real server for delivery. My preference is for postfix but our IT staff seems set on using sendmail (or Exchange) for everything so hints/pointers for either server would be helpful. Thanks a lot.

  Read the article

• Graphics and USB devices freezing soon after OS loads

  - by Andrew

  I run Ubuntu/Windows dual boot. Last night I started the upgrade to Ubuntu 12.04, and my computer has not worked since in either Windows or Ubuntu. Here's what I got when I rebooted after the upgrade, and continue to get every time I boot: Gets to GRUB screen OK. Choose Ubuntu - black screen or crazy purple lines. At first I assumed something went wrong with the upgrade (often happens). Choose Windows - works fine, I log in, but soon after that the graphics freeze (sometimes with purple artifacts). The keyboard and mouse (both USB) also lose power at the same instant, and none of the USB ports have power to them. This happens sooner or later every time I boot. Update: the HDD also appears to lose power at the same point. I have tried a live CD, but my computer refuses to boot any CD even after disabling all other boot options in the BIOS. I have disconnected everything except keyboard, mouse, graphics card with one monitor, one RAM sick and HDD; no change. I also took the little battery out to reset CMOS. I am pretty sure no matter how wrong the Ubuntu upgrade went, it wouldn't cause the above symptoms in Windows. So the only explanation I can think of is that a hardware failure occurred at the same time. Some possible causes of this I can think of are: A couple of days before this, I added a third screen (which worked fine). About a week before, my house lost power in a storm (no ill effects over the past few days though). What can I do, other than buy a new motherboard/CPU and hope it works? Unfortunately I don't have another box to swap parts into to test at the moment.

  Read the article

• Referencing SQL Server 2008 R2 SMO from Visual Studio 2010

  - by user69508

  Hello. We read a number of things about referencing SQL Server SMO from Visual Studio but still don't have the definite answers we need. So, here it goes... A number of years ago we created a C# application using Visual Studio 2005 and SQL Server 2005. In that application, we added .NET references to a number of SQL Server SMO objects, and everything worked fine. Those references were: Microsoft.SqlServer.ConnectionInfo GAC 9.0.242.0 Microsoft.SqlServer.Smo GAC 9.0.242.0 Microsoft.SqlServer.SqlEnum GAC 9.0.242.0 We have now migrated to Visual Studio 2010 and SQL Server 2008 R2. However, when we try to reference those same SMO objects for SQL Server 2008 R2, they don't appear in the .NET references tab. We're wanting to reference the SQL Server 2008 R2 version of those same SMO assemblies for our upgraded C# application. On our development machines, we have SQL Server 2008 R2 Developer installed with all options, including the SDK such that the assemblies are found in C:\Program Files (x86)\Microsoft SQL Server\100\SDK\Assemblies. So, my first questions are: Are we supposed to do file references to the SMO assemblies instead of .NET references in Visual Studio 2010 w/ SQL Server 2008 R2? Or, is there some problem with our development machines such that the SMO assemblies are not appearing in the .NET references tab? Next, our production machines will have SQL Server 2008 R2 Workgroup installed with the client tools option selected, thus providing those same SMO assemblies in C:\Program Files (x86)\Microsoft SQL Server\100\SDK\Assemblies. So, the next questions are: When we release to production, are we supposed to redistribute the SMO assemblies with our application? Or, will our application work on the production servers without redistributing the SMO assemblies (since the client tools/SMO assemblies have been installed)? What else????? Thanks for the help!

  Read the article

• PHP & IIS 6 Encoding problem

  - by Alexander

  The server is running Windows 2003 with IIS 6.0.3790.1830 x86 (iis.dll). My database server is Microsoft SQL Server 2000. My PHP version is 5.3. The original application is hosted on appserv1 and it's database is on dbserv1. It's working fine, everything is tuned up, running great. It was needed to place the same application (different modules) on another server, for other uses, so I copied the database on dbserv2, configured appserv2 to host the application, so I achieved 2 almost identical copies. Both dbserv1 and dbserv2 use the same encoding, both appserv1 and appserv2 are on IIS6 with the same PHP configurations. I also tried my best to have the same settings in the IIS. I also made sure that I pass the encoding information both in the HTTP headers and in the meta tags with http-equiv. Both applications use utf-8. The Problem is that the copy of the application doesn't display the non-ASCII characters normally in the browser, even if the browser detects correctly the UTF-8 encoding of the page. First I thought it was a database issue, given the fact that MSSQL 2000 doesn't support UTF-8, and instead it uses UCS-2, but when I redirected the application on appserv2 to work with the database on dbserv1, it had the same encoding problems. This is why I am asking in what way I can make it work. thank you for reading.

  Read the article

• Mainboard shuts itself off after half a second or so

  - by heishe

  Here's the problem: When I start the PC, the mainboard powers up, then stays that way maybe 0.2-0.5 seconds, and then shuts off again. I say mainboard, and not PC, because I removed all the parts from the system and disconnected everything but the mainboard power supply (the broad 12 pin thingy). When I have the other parts (cpu, graphics card, ram, etc.) installed and connected, the basic behaviour stays the same, but now the mainboard runs for about 6 or 7 seconds (this is a guess) before shutting off. This all started when my monitor wouldn't receive a video signal today, without giving POSTs, so I took the graphics card and the RAM out to see if it changes anything. It didn't, except that from that point on the mainboard would start to have this behavior where it just stays on for a very short time and then shuts off again. I already tested it with a backup PSU - same behavior. What could this be? I'm thinking it can't be on a physical level (transistors burned through or something like that), since then the mainboard either shouldn't start at all or it should detect hardware failures in non-essential parts of the syste and start beeping. Sorry, I forgot to mention. It's an MSI P67A-C43. I already checked the capacitors if someone popped, but I can't find anything. I also tried resetting the cmos, but that didn't change anything.

  Read the article

• JavaScript is not pointing correctly on IIS7 running behind Apache mod_proxy

  - by sohum

  So here's my setup. I've got a DynDNS account since I have a dynamic IP. I have Apache listening on port 80 and IIS7 on port 8080. I don't want users to have to enter in mydyndns.dyndns.com:8080 to get to IIS7, so I've added the following code to my Apache httpd.conf file to enable a proxy/reverse proxy: <VirtualHost *:80> ProxyPass / http://localhost:8080/myASPSite/ ProxyPassReverse / http://localhost:8080/myASPSite/ ServerName myaspsite.mydomain.com </VirtualHost> I've got a CNAME record set up on my DNS so that myaspsite.mydomain.com redirects to mydyndns.dyndns.com. When I type in myaspsite.mydomain.com into my browser, everything works beautifully... mostly. IIS7 serves up the ASPX pages and visitors to the site don't know any better. A problem arises, however, when I add Ajax Control Toolkit controls into my ASPX website, because these generate JavaScript and apparently mod_proxy_html isn't geared to handle the JS URIs properly. Sure enough, when I open up the source of my ASPX page, it has script elements as follows: <script src="/myASPSite/WebResource.axd?xyz" type="text/javascript"></script> <script src="/myASPSite/ScriptResource.axd?xyz" type="text/javascript"></script> Sure enough, these scripts are attempting to be resolved at http://myaspsite.mydomain.com/myASPSite/WebResource..., which through the proxy translates to localhost:8080/myASPSite/myASPSite/.... How can I solve this problem. The couple of websites I found suggested turning on ProxyHTMLExtended but when I tried doing that, the server did not start. I'm guessing I didn't know how to do it properly. Anyone has a handy couple of config lines that I can add to my Apache conf file to get this working as I need? I'm using Apache 2.2.11. Thanks!

  Read the article

• Which linux distributions offer seamless support for UEFI and an LVM root out of the box?

  - by Jannik Jochem

  My new ultrabook (an Asus UX32VD) requires UEFI in order to boot from the internal harddisk. I use an LVM partition which contains my root fs and dual-boot Windows 8. I somehow managed to get this working on Sabayon Linux, however the overall process was pretty painful, and system upgrades keep breaking my configuration because everything depends on a hand-configured kernel and a hand-crafted GRUB2 configuration. This causes a lot of hassle and distractions for me, so I am considering to switch to a different distribution. However, I cannot find any concrete resources that precisely document the state of UEFI support in the popular distributions. As an example, the length of the Ubuntu wiki page on UEFI suggests that installing on UEFI systems is a non-trivial process, and this AskUbuntu thread on encrypted LVM on UEFI systems suggests that LVM might also be a problem. I know that this question seems somewhat open-ended, so I'll formulate concrete questions: Are there any Linux distributions with an installer that supports installing to an LVM root in a UEFI boot setting where Windows 8 is dual-booted? Which distributions support UEFI without having to jump through hoops in order to bootstrap into a UEFI-booted system or requiring manual configuration of the boot manager?

  Read the article

• Vyatta masquerade out bridge interface

  - by miquella

  We have set up a Vyatta Core 6.1 gateway on our network with three interfaces: eth0 - 1.1.1.1 - public gateway/router IP (to public upstream router) eth1 - 2.2.2.1/24 - public subnet (connected to a second firewall 2.2.2.2) eth2 - 10.10.0.1/24 - private subnet Our ISP provided the 1.1.1.1 address for us to use as our gateway. The 2.2.2.1 address is so the other firewall (2.2.2.2) can communicate to this gateway which then routes the traffic out through the eth0 interface. Here is our current configuration: interfaces { bridge br100 { address 2.2.2.1/24 } ethernet eth0 { address 1.1.1.1/30 vif 100 { bridge-group { bridge br100 } } } ethernet eth1 { bridge-group { bridge br100 } } ethernet eth2 { address 10.10.0.1/24 } loopback lo { } } service { nat { rule 100 { outbound-interface eth0 source { address 10.10.0.1/24 } type masquerade } } } With this configuration, it routes everything, but the source address after masquerading is 1.1.1.1, which is correct, because that's the interface it's bound to. But because of some of our requirements here, we need it to source from the 2.2.2.1 address instead (what's the point of paying for a class C public subnet if the only address we can send from is our gateway!?). I've tried binding to br100 instead of eth0, but it doesn't seem to route anything if I do that. I imagine I'm just missing something simple. Any thoughts?

  Read the article

• Request bursting from web application Load Tests

  - by MaseBase

  I'm migrating our web and database hosting to a new environment on all new machines. I've recently performed a Load Test using WAPT to generate load from multiple distributed clients. The server has plenty of room to handle the traffic load, but I'm seeing an odd pattern of incoming traffic during the load tests. Here is the gist of our setup: Firewall server running MS Forefront TMG 2010 on Win 2k8 server Request routing done by IIS Application Request Routing on firewall machine Web server is a Hyper-V VM on the Database server (which is the host OS) These machines are hefty with dual-CPU's with six cores (12 total procs) Web server running IIS 7.5 Web applications built in ASP.NET 2.0, with 1 ISAPI filter (Url Rewrite) in front What I'm seeing during the load tests is that the requests all come through in bursts. Even though I have 7 different distributed clients sending traffic loads, the requests come through about 300-500 requests at a time. The performance monitor shows nearly all of the counters moving through this pattern, where a burst of requests comes in the req/sec jumps to 70, the queued requests jumps to 500, the current requests jumps up, the CPU jumps up, everything. Then once it's handled that group of requests, it has a lull for nearly 10 seconds where nearly nothing is happening. 0-5 req/sec, 0 queued requests, minimal CPU usage. Then after 10 seconds of inactivity, another burst comes through, spiking all of the counters once again. What I can't figure out is why the requests are coming through in bursts when I know that the load being generated is not sent that way, especially considering the various load-generating clients sending traffic all in different intervals with random think time's between each request. Is there something in the layers between Hyper-V or perhaps in the hardware which might cause this coalesce of requests together? Here is what i'm looking at, the highlighted metric is Requests/sec, but the others critical counter go with it: Requests Queued (which I'd obviously like to keep as close to 0 as possible). Any ideas on this?

  Read the article

• Downmix ALL SYSTEM audio to mono - Windows 7

  - by Mike K.

  I'm deaf in one ear and want to use my headphones when playing a game and talking with my friends on Skype/TS/Mumble/etc while also sometimes listening to music. I need ALL my system audio to be downmixed to mono so that my ONE hearing ear gets ALL audio channels instead of split stereo audio. No, none of the other similar questions on superuser have a solution. My headphone properties does not have a 'Mono' option, I don't have a 'Headphone Virtualization' option, and my Realtek HD audio driver software doesn't have these options either (driver was updated 11/14/2012). Don't even talk about setting the balance of one side of the headphones to 0. You're not paying attention if you suggest that. JACK and Virtual Audio Cable didn't work. It's possible I configured them wrong, but I followed the steps I found in related questions and still got split stereo out. TL;DR I need a viable, working, software solution (I say software because I have a USB headset) for forcing ALL system audio to mono so that I can hear literally everything through the one earpiece. Thanks!

  Read the article

• Configuring port forwarding for SSH - no response outside LAN [migrated]

  - by WinnieNicklaus

  I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

  Read the article

• Why doesn't apache2 consistently load template fragments from memcached?

  - by Hobhouse

  I run a webserver on an ubuntu box in the rackspacecloud with django 1.0x, apache2/WSGI and memcached 1.2.2. Some of my templates make use of template fragment caching: {% load cache %} {% cache 604800 keyname %} <!-- cache: {% now "H:i, j. b" %} --> {{ my_content }} {% endcache %} When I reload apache2 everything is fine. If keyname is not set, my_content is generated and keyname is set in memcached. After that, my_content is served from memcached. My problem is that after some hours (notably less time than 604800 seconds ), apache2 seems to stop talking to memcached, and my_content is generated from scratch everytime. When this happens I can still set and get keys from memcached from my python shell. Memcached also has more than enough memory to store keys. But to get apache2 to start talking to memcached again I have to restart apache2, and then it will once again start to get the now several hours old keys from memcached. What can be the reason for this behaviour, and how do I fix it?

  Read the article

• VMware Virtual Infrastructure Web Access not starting on Fedora 14

  - by FusionHammer

  I am running a Fedora 14 server with VMware Server 2. When I initially installed VMware Server, everything was working fine. This included accessing Web Access on port 8333 (https) and 8222 (http). I had to perform a server restart and afterwards, the Web Access is not starting when I run: /etc/init.d/vmware-mgmt start The VMware Server Host Agent starts [OK], but the Web Access has no [OK] or [Failed] next to it. I also checked ports 8333 and 8222 by running a netstat, but neither are showing up. In addition, I checked the proxy.log and client.log files in the following directory: /usr/lib/vmware/webAccess/tomcat/apache-tomcat-6.0.16/logs/ The proxy.log doesn't have entries in it past 9-18-2012, which is the date the server restart occurred. The client.log is empty. I not sure what is causing this issue or what log files will be helpful in narrowing down the cause. I could re-install VMware Server, but I would like to narrow down the cause as it could occur again with the new re-installed environment.

  Read the article

• windows cant "see" camera

  - by user330401

  So I bought a lil emerson camera and I am trying to get it to read the thing on windows 7. The instructions for the camer say when you first hook it up via usb AUTOPLAY will come up and your good to go. Well that worked for me the first time I hooked it up. However the 2nd time, it started trying to install drivers. Since then I can't get it to show up in windows explorer. I have tried disabling and uninstalling everything and trying to start from scratch but its useless, I'm stuck with having to pull the sd card everytime. I really dont like doing this as its a cheap camera, so if I can fix the communication between the devices via usb I would be really happy. As of right now the device installation shows a checked USB COMPOSITE DEVICE and 3 X'd GENERIC IMAGE DEVIC. Can someone please help me get this sorted. PS there are no drivers for this camera, not in the packaging, not available from emerson, and to be honest it shouldn't need any. The only function the camera has when hooked up via USB is charging and access to the DCIM. The charging still works, but the drive just won't load. Any suggestions?

  Read the article

• How to generate thumbnails for less common video containers (mkv, ogm, mp4, flv, rmvb and mov) in wi

  - by fluxtendu

  So how to generate thumbnails for these containers? I know that the install of "DivX Plus Tech Preview: MKV on Windows 7" does it for MKV. But I think that only some registry changes are really necessary and I want it for other containers. If it's possible to avoiding the install of (always bloated) codecs packs it would be nice... Maybe only installing ffdshow or essential and separated codecs. (some time ago I have try reg files for vista without success...) Update: I have installed Win7codecs & tweaked a little its settings and I got almost everything I want. (I have also re-installed the relevant part of the divx plus tech preview to get something else than an all black preview for MKV) Issues that I still want to resolve: Find a cleaner & lighter method Almost all my rmvb and mov files got an all black preview (installing real media/quick time alternative doesn't help, is it the same with the officials?) With almost all containers (avi, mkv, ogm, mpg), I have (few) random files that don't get the preview. I could play them in WMP or another player and don't have found a pattern in the codecs used. All wmv, flv and mp4 have previews but I have less files in these containers. (I clear my thumbnails cache to test them) More generally I would like to understand how windows handle the containers & codecs to generate the previews. And a software that let me choose arbitrarily the pictures previewed would be convenient too

  Read the article

• Elevating UAC via .bat file?

  - by jslaker

  Pretty straightforward one that I'm having trouble finding an answer to. serverfault previously helped me with finding a way to automate Windows updates without using WSUS. It's working fantastically, but to run it over the network, you have to first mount a shared drive. That's pretty simple XP since you just mount the drive and run the updater. On Vista and W7, though, this all has to be done with elevated privileges to work correctly. The UAC account can't see network drives mounted by the regular user, so in order to get everything working, I have to mount the share via net use from an escalated shell. I'd like to automate mounting this share and launching the updater via a simple .bat file. I could probably just instruct everybody to right click "Run as Administrator" on the .bat file, but I'd like to keep things as simple as possible and have the .bat automatically prompt the user to escalate their privileges. Since these computers don't belong to us, I can't count on anything like Powershell being installed, so that rules any solution along those lines out and pretty much have to rely on things that would be included in an RTM Vista install. I'm hoping I'm mostly missing something obvious here. :)

  Read the article

• GlusterFS is failing to mount on boot

  - by J. Pablo Fernández

  I'm running the official GlusterFS 3.5 packages on Ubuntu 12.04 and everything seems to be working fine, except mounting the GlusterFS volumes at boot time. This is what I see in the log files: [2014-06-13 08:52:28.139382] I [glusterfsd.c:1959:main] 0-/usr/sbin/glusterfs: Started running /usr/sbin/glusterfs version 3.5.0 (/usr/sbin/glusterfs --volfile-server=koraga --volfile-id=/private_uploads /var/www/shared/private/uploads) [2014-06-13 08:52:28.147186] I [socket.c:3561:socket_init] 0-glusterfs: SSL support is NOT enabled [2014-06-13 08:52:28.147237] I [socket.c:3576:socket_init] 0-glusterfs: using system polling thread [2014-06-13 08:52:28.148183] E [socket.c:2161:socket_connect_finish] 0-glusterfs: connection to 176.58.113.205:24007 failed (Connection refused) [2014-06-13 08:52:28.148236] E [glusterfsd-mgmt.c:1601:mgmt_rpc_notify] 0-glusterfsd-mgmt: failed to connect with remote-host: koraga (No data available) [2014-06-13 08:52:28.148251] I [glusterfsd-mgmt.c:1607:mgmt_rpc_notify] 0-glusterfsd-mgmt: Exhausted all volfile servers [2014-06-13 08:52:28.148477] W [glusterfsd.c:1095:cleanup_and_exit] (-->/usr/lib/x86_64-linux-gnu/libgfrpc.so.0(rpc_transport_notify+0x27) [0x7fe077f8e0f7] (-->/usr/lib/x86_64-linux-gnu/libgfrpc.so.0(rpc_clnt_notify+0x1a4) [0x7fe077f91cc4] (-->/usr/sbin/glusterfs(+0xcada) [0x7fe078655ada]))) 0-: received signum (1), shutting down [2014-06-13 08:52:28.148513] I [fuse-bridge.c:5444:fini] 0-fuse: Unmounting '/var/www/shared/private/uploads'. My fstab contains: proc /proc proc defaults 0 0 /dev/xvda / ext4 noatime,errors=remount-ro 0 1 /dev/xvdb none swap sw 0 0 /dev/xvdc /var/lib/glusterfs/brick01 ext4 defaults 1 2 koraga:/private_uploads /var/www/shared/private/uploads glusterfs defaults,_netdev 0 0 Any ideas what's going on and/or how to fix it?

  Read the article

< Previous Page | 505 506 507 508 509 510 511 512 513 514 515 516  | Next Page >