Search Results

Search found 15939 results on 638 pages for 'low memory'.

Page 509/638 | < Previous Page | 505 506 507 508 509 510 511 512 513 514 515 516  | Next Page >

• Configure 27" 2560x1440 for a monitor with corrupt EDID

  - by Aras

  I am trying to get a monitor work with my Ubuntu laptop. The monitor is this cheap 27" Korean monitors which has a 2560x1440 resolution -- and nothing else. Here are some specifications of this monitor: 2560x1440 @60Hz Only one dual link DVI-D input -- no other input port (no HDMI or display port) no OSD no scalar reports corrupt EDID does 2560x1440 @60Hz, did I say that already? Anyways, the monitor works beautifully with my Ubuntu desktop which has an nVidia card with DVI output. However, I am having problem using this monitor with my laptop. After some searching around I found a few posts suggesting to use an active adaptor for mini display port, so I went and bought a mini display to dual link DVI-D adaptor.. When using this adaptor the monitor is recognized by nvidia-settings tool but with incorrect resolution information. As you can see the monitor is incorrectly recognized and there are no other resolution available to set. This post on ubuntu forums and this other post on overclock both suggest that the monitor is reporting corrupt EDID file. I have tried following their instructions, but so far I have not been able to display any image on the monitor from my laptop. The laptop I am using is an ASUS G75VW with a 1920x1080 screen. It has a VGA, an HDMI 1.4a, and a mini display port. The graphic card is an nvidia gforce gtx 660M with 2GB dedicated memory. I am running Ubuntu 12.10 on here which I upgrade from 12.04 a few weeks ago. As I said I have tried several suggestions, including specifying Modeline in xorg.conf and also linking to EDID files I found from those forum posts above. However, I am not sure if the EDID files I found are suitable for my monitor. I think the solution to my problem consist of obtaining the EDID file of my monitor and then fixing it and modifying xorg.conf to force nvidia driver to load the correct resolution. However, I am not sure what steps I need to take to do this. Here is the part of sudo xrandr --prop output that is related to this monitor: DP-1 connected 800x600+1920+0 (normal left inverted right x axis y axis) 0mm x 0mm SignalFormat: DisplayPort supported: DisplayPort ConnectorType: DisplayPort ConnectorNumber: 3 (0x00000003) _ConnectorLocation: 3 (0x00000003) 800x600 60.3*+ I was expecting to see the EDID file in this output as was mentioned in this post, but it is not there. After several hours of tweaking X configurations, I decided it was time to ask for help here. I would really appreciate if someone with experience regarding EDID and X configuration could give me a hand to solve this issue.

  Read the article

• Keepin’ It Simple with StorageTek SL150

  - by Kristin Rose

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Are your customers archive and data protection environments getting out of hand?  Are they looking for a little simplicity in their lives? How about some scalability? Or are they looking for a way to save on capital and operational expenses? If you answered yes to any of these, then  Oracle's new StorageTek SL150 Modular Tape Library is the product for you. It beats the competition in terms of simplicity, scalability and savings, and provides some seriously wallet friendly revenue opportunities for you. If the long-term service annuities on the SL150 aren’t convincing enough, then the resale margins, rebates and follow-on revenue from modular upgrades will be!  The SL150 simplifies StorageTek’s tape portfolio by replacing three products with one scalable solution that  provides an entry point for repeat business within accounts. The SL150 expands your potential storage customer base to smaller companies with low cost, simple upgrades and streamlined management that help alleviate key customer pain points. With the SL150, your customers will be able to simplify growth of their archive and data protection environments with small entry configurations and 10x growth, something that would require multiple box swaps across up to three product categories with competitive products. With the SL150, Oracle can help you provide greater customer satisfaction with  Simplicity, Scalability and Savings! We know you’re probably wondering how you can get started and sell this new and magnificent product… Well, look no further because the only thing you need to do is complete the SL150 Guided Learning Paths (GLPs). For some extra insight, watch the video below on the new StorageTek SL150 modular tape library, and don’t forget to ‘tweet’ this post, and share it on Facebook to spread the good news! Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Wishing you Simplicity, Scalability and Savings, The OPN Communications Team

  Read the article

• Know Your Audience, And/Or Your Customer

  - by steve.diamond

  Yesterday I gave an internal presentation to about 20 Oracle employees on "messaging," not messaging technology, but embarking on the process of building messages. One of the elements I covered was the importance of really knowing and understanding your audience. As a humorous reference I included two side-by-side photos of Oakland A's fans and Oakland Raiders fans. The Oakland A's fans looked like happy-go-lucky drunk types. The Oakland Raiders fans looked like angry extras from a low budget horror flick. I then asked my presentation attendees what these two groups had in common. Here's what I heard. --They're human (at least I THINK they're human). --They're from Oakland. --They're sports fans. After that, it was anyone's guess. A few days earlier we were putting the finishing touches on a sales presentation for one of our product lines. We had included an upfront "lead in" addressing how the economy is improving, yet that doesn't mean sales executives will have any more resources to add to their teams, invest in technology, etc. This "lead in" included miscellaneous news article headlines and statistics validating the slowly improving economy. When we subjected this presentation to internal review two days ago, this upfront section in particular was scrutinized. "Is the economy really getting better? I (exclamation point) don't think it's really getting better. Haven't you seen the headlines coming out of Greece and Europe?" Then the question TO ME became, "Who will actually be in the audience that sees and hears this presentation? Will s/he be someone like me? Or will s/he be someone like the critic who didn't like our lead-in?" We took the safe route and removed that lead in. After all, why start a "pitch" with a component that is arguably subjective? What if many of our audience members are individuals at organizations still facing a strong headwind? For reasons I won't go into here, it was the right decision to make. The moral of the story: Make sure you really know your audience. Harness the wisdom of the information your organization's CRM systems collect to get that fully informed "customer view." Conduct formal research. Conduct INFORMAL research. Ask lots of questions. Study industries and scenarios that have nothing to do with yours to see "how they do it." Stop strangers in coffee shops and on the street...seriously. Last week I caught up with an old friend from high school who recently retired from a 25 year career with the USMC. He said, "I can learn something from every single person I come into contact with." What a great way of approaching the world. Then, think about and write down what YOU like and dislike as a customer. But also remember that when it comes to your company's products, you are most likely NOT the customer, so don't go overboard in superimposing your own world view. Approaching the study of customers this way adds rhyme, reason and CONTEXT to lengthy blog posts like this one. Know your audience.

  Read the article

• Migrating SQL Server Databases – The DBA’s Checklist (Part 3)

  - by Sadequl Hussain

  Continuing from Part 2 of the Database Migration Checklist series: Step 10: Full-text catalogs and full-text indexing This is one area of SQL Server where people do not seem to take notice unless something goes wrong. Full-text functionality is a specialised area in database application development and is not usually implemented in your everyday OLTP systems. Nevertheless, if you are migrating a database that uses full-text indexing on one or more tables, you need to be aware a few points. First of all, SQL Server 2005 now allows full-text catalog files to be restored or attached along with the rest of the database. However, after migration, if you are unable to look at the properties of any full-text catalogs, you are probably better off dropping and recreating it. You may also get the following error messages along the way: Msg 9954, Level 16, State 2, Line 1 The Full-Text Service (msftesql) is disabled. The system administrator must enable this service. This basically means full text service is not running (disabled or stopped) in the destination instance. You will need to start it from the Configuration Manager. Similarly, if you get the following message, you will also need to drop and recreate the catalog and populate it. Msg 7624, Level 16, State 1, Line 1 Full-text catalog ‘catalog_name‘ is in an unusable state. Drop and re-create this full-text catalog. A full population of full-text indexes can be a time and resource intensive operation. Obviously you will want to schedule it for low usage hours if the database is restored in an existing production server. Also, bear in mind that any scheduled job that existed in the source server for populating the full text catalog (e.g. nightly process for incremental update) will need to be re-created in the destination. Step 11: Database collation considerations Another sticky area to consider during a migration is the collation setting. Ideally you would want to restore or attach the database in a SQL Server instance with the same collation. Although not used commonly, SQL Server allows you to change a database’s collation by using the ALTER DATABASE command: ALTER DATABASE database_name COLLATE collation_name You should not be using this command for no reason as it can get really dangerous.  When you change the database collation, it does not change the collation of the existing user table columns.  However the columns of every new table, every new UDT and subsequently created variables or parameters in code will use the new setting. The collation of every char, nchar, varchar, nvarchar, text or ntext field of the system tables will also be changed. Stored procedure and function parameters will be changed to the new collation and finally, every character-based system data type and user defined data types will also be affected. And the change may not be successful either if there are dependent objects involved. You may get one or multiple messages like the following: Cannot ALTER ‘object_name‘ because it is being referenced by object ‘dependent_object_name‘. That is why it is important to test and check for collation related issues. Collation also affects queries that use comparisons of character-based data.  If errors arise due to two sides of a comparison being in different collation orders, the COLLATE keyword can be used to cast one side to the same collation as the other. Continues…

  Read the article

• MAXDOP in SQL Azure

  - by Herve Roggero

  In my search of better understanding the scalability options of SQL Azure I stumbled on an interesting aspect: Query Hints in SQL Azure. More specifically, the MAXDOP hint. A few years ago I did a lot of analysis on this query hint (see article on SQL Server Central:  http://www.sqlservercentral.com/articles/Configuring/managingmaxdegreeofparallelism/1029/).  Here is a quick synopsis of MAXDOP: It is a query hint you use when issuing a SQL statement that provides you control with how many processors SQL Server will use to execute the query. For complex queries with lots of I/O requirements, more CPUs can mean faster parallel searches. However the impact can be drastic on other running threads/processes. If your query takes all available processors at 100% for 5 minutes... guess what... nothing else works. The bottom line is that more is not always better. The use of MAXDOP is more art than science... and a whole lot of testing; it depends on two things: the underlying hardware architecture and the application design. So there isn't a magic number that will work for everyone... except 1... :) Let me explain. The rules of engagements are different. SQL Azure is about sharing. Yep... you are forced to nice with your neighbors.  To achieve this goal SQL Azure sets the MAXDOP to 1 by default, and ignores the use of the MAXDOP hint altogether. That means that all you queries will use one and only one processor.  It really isn't such a bad thing however. Keep in mind that in some of the largest SQL Server implementations MAXDOP is usually also set to 1. It is a well known configuration setting for large scale implementations. The reason is precisely to prevent rogue statements (like a SELECT * FROM HISTORY) from bringing down your systems (like a report that should have been running on a different in the first place) and to avoid the overhead generated by executing too many parallel queries that could cause internal memory management nightmares to the host Operating System. Is summary, forcing the MAXDOP to 1 in SQL Azure makes sense; it ensures that your database will continue to function normally even if one of the other tenants on the same server is running massive queries that would otherwise bring you down. Last but not least, keep in mind as well that when you test your database code for performance on-premise, make sure to set the DOP to 1 on your SQL Server databases to simulate SQL Azure conditions.

  Read the article

• Changing the action of a hyperlink in a Silverlight RichTextArea

  - by Marc Schluper

  The title of this post could also have been "Move over Hyperlink, here comes Actionlink" or "Creating interactive text in Silverlight." But alas, there can be only one. Hyperlinks are very useful. However, they are also limited because their action is fixed: browse to a URL. This may have been adequate at the start of the Internet, but nowadays, in web applications, the one thing we do not want to happen is a complete change of context. In applications we typically like a hyperlink selection to initiate an action that updates a part of the screen. For instance, if my application has a map displayed with some text next to it, the map would react to a selection of a hyperlink in the text, e.g. by zooming in on a location and displaying additional locational information in a popup. In this way, the text becomes interactive text. It is quite common that one company creates and maintains websites for many client companies. To keep maintenance cost low, it is important that the content of these websites can be updated by the client companies themselves, without the need to involve a software engineer. To accommodate this scenario, we want the author of the interactive text to configure all hyperlinks (without writing any code). In a Silverlight RichTextArea, the default action of a Hyperlink is the same as a traditional hyperlink, but it can be changed: if the Command property has a value then upon a click event this command is called with the value of the CommandParameter as parameter. How can we let the author of the text specify a command for each hyperlink in the text, and how can we let an application react properly to a hyperlink selection event? We are talking about any command here. Obviously, the application would recognize only a specific set of commands, with well defined parameters, but the approach we take here is generic in the sense that it pertains to the RichTextArea and any command. So what do we require? We wish that: As a text author, I can configure the action of a hyperlink in a (rich) text without writing code; As a text author, I can persist the action of a hyperlink with the text; As a reader of persisted text, I can click a hyperlink and the configured action will happen; As an application developer, I can configure a control to use my application specific commands. In an excellent introduction to the RichTextArea, John Papa shows (among other things) how to persist a text created using this control. To meet our requirements, we can create a subclass of RichTextArea that uses John's code and allows plugging in two command specific components: one to prompt for a command definition, and one to execute the command. Since both of these plugins are application specific, our RichTextArea subclass should not assume anything about them except their interface. public interface IDefineCommand { void Prompt(string content, // the link content Action<string, object> callback); // the method called to convey the link definition } public interface IPerformCommand : ICommand {} The IDefineCommand plugin receives the content of the link (the text visible to the reader) and displays some kind of control that allows the author to define the link. When that's done, this (possibly changed) content string is conveyed back to the RichTextArea, together with an object that defines the command to execute when the link is clicked by the reader of the published text. The IPerformCommand plugin simply implements System.Windows.Input.ICommand. Let's use MEF to load the proper plugins. In the example solution there is a project that contains rudimentary implementations of these. The IDefineCommand plugin simply prompts for a command string (cf. a command line or query string), and the IPerformCommand plugin displays a MessageBox showing this command string. An actual application using this extended RichTextArea would have its own set of commands, each having their own parameters, and hence would provide more user friendly application specific plugins. Nonetheless, in any case a command can be persisted as a string and hence the two interfaces defined above suffice. For a Visual Studio 2010 solution, see my article on The Code Project.

  Read the article

• SQL SERVER – 2011 – Introduction to SEQUENCE – Simple Example of SEQUENCE

  - by pinaldave

  SQL Server 2011 will contain one of the very interesting feature called SEQUENCE. I have waited for this feature for really long time. I am glad it is here finally. SEQUENCE allows you to define a single point of repository where SQL Server will maintain in memory counter. USE AdventureWorks2008R2 GO CREATE SEQUENCE [Seq] AS [int] START WITH 1 INCREMENT BY 1 MAXVALUE 20000 GO SEQUENCE is very interesting concept and I will write few blog post on this subject in future. Today we will see only working example of the same. Let us create a sequence. We can specify various values like start value, increment value as well maxvalue. -- First Run SELECT NEXT VALUE FOR Seq, c.CustomerID FROM Sales.Customer c GO -- Second Run SELECT NEXT VALUE FOR Seq, c.AccountNumber FROM Sales.Customer c GO Once the sequence is defined, it can be fetched using following method. Every single time new incremental value is provided, irrespective of sessions. Sequence will generate values till the max value specified. Once the max value is reached, query will stop and will return error message. Msg 11728, Level 16, State 1, Line 2 The sequence object ‘Seq’ has reached its minimum or maximum value. Restart the sequence object to allow new values to be generated. We can restart the sequence from any particular value and it will work fine. -- Restart the Sequence ALTER SEQUENCE [Seq] RESTART WITH 1 GO -- Sequence Restarted SELECT NEXT VALUE FOR Seq, c.CustomerID FROM Sales.Customer c GO Let us do final clean up. -- Clean Up DROP SEQUENCE [Seq] GO There are lots of things one can find useful about this feature. We will see that in future posts. Here is the complete code for easy reference. USE AdventureWorks2008R2 GO CREATE SEQUENCE [Seq] AS [int] START WITH 1 INCREMENT BY 1 MAXVALUE 20000 GO -- First Run SELECT NEXT VALUE FOR Seq, c.CustomerID FROM Sales.Customer c GO -- Second Run SELECT NEXT VALUE FOR Seq, c.AccountNumber FROM Sales.Customer c GO -- Restart the Sequence ALTER SEQUENCE [Seq] RESTART WITH 1 GO -- Sequence Restarted SELECT NEXT VALUE FOR Seq, c.CustomerID FROM Sales.Customer c GO -- Clean Up DROP SEQUENCE [Seq] GO Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQLServer, T SQL, Technology

  Read the article

• Travelling MVP #4: DevReach 2012

  - by DigiMortal

  Our next stop after Varna was Sofia where DevReach happens. DevReach is one of my favorite conferences in Europe because of sensible prices and strong speakers line-up. Also they have VIP-party after conference and this is good event to meet people you don’t see every day, have some discussion with speakers and find new friends. Our trip from Varna to Sofia took about 6.5 hours on bus. As I was tired from last evening it wasn’t problem for me as I slept half the trip. After smoking pause in Velike Tarnovo I watched movies from bus TV. We had supper later in city center Happy’s – place with good meat dishes and nice service. And next day it begun…. :) DevReach 2012 DevReach is held usually in Arena Mladost. It’s near airport and Telerik office. The event is organized by local MVP Martin Kulov together with Telerik. Two days of sessions with strong speakers is good reason enough for me to go to visit some event. Some topics covered by sessions: Windows 8 development web development SharePoint Windows Azure Windows Phone architecture Visual Studio Practically everybody can find some interesting session in every time slot. As the Arena is not huge it is very easy to go from one sessions to another if selected session for time slot is not what you expected. On the second floor of Arena there are many places where you can eat. There are simple chunk-food places like Burger King and also some restaurants. If you are hungry you will find something for your taste for sure. Also you can buy beer if it is too hot outside :) Weather was very good for October – practically Estonian summer – 25C and over. Sessions I visited Here is the list of sessions I visited at DevReach 2012: DevReach 2012 Opening & Welcome Messsage with Martin Kulov and Stephen Forte Principled N-Tier Solution Design with Steve Smith Data Patterns for the Cloud with Brian Randell .NET Garbage Collection Performance Tips with Sasha Goldshtein Building Secured, Scalable, Low-latency Web Applications with the Windows Azure Platform with Ido Flatow It’s a Knockout! MVVM Style Web Applications with Charles Nurse Web Application Architecture – Lessons Learned from Adobe Brackets with Brian Rinaldi Demystifying Visual Studio 2012 Performance Tools with Martin Kulov SPvNext – A Look At All the Exciting And New Features In SharePoint with Sahil Malik Portable Libraries – Why You Should Care with Lino Tadros I missed some sessions because of some death march projects that are going and that I have to coordinate but it was not big loss as I had time to walk around in session venue neighborhood and see Sofia Business Park. Next year again! I will be there again next year and hopefully more guys from Estonia will join me. I think it’s good idea to take short vacation for DevReach time and do things like we did this time – Bucharest, Varna, Sofia. It’s only good idea to plan some more free time so we are not very much in hurry and also we have no work stuff to do on the trip. This far this trip has been one of best trips I have organized and I will go and meet all those guys in this region again! :)

  Read the article

• Pixel Perfect Collision Detection in Cocos2dx

  - by Happybirthday

  I am trying to port the pixel perfect collision detection in Cocos2d-x the original version was made for Cocos2D and can be found here: http://www.cocos2d-iphone.org/forums/topic/pixel-perfect-collision-detection-using-color-blending/ Here is my code for the Cocos2d-x version bool CollisionDetection::areTheSpritesColliding(cocos2d::CCSprite *spr1, cocos2d::CCSprite *spr2, bool pp, CCRenderTexture* _rt) { bool isColliding = false; CCRect intersection; CCRect r1 = spr1-boundingBox(); CCRect r2 = spr2-boundingBox(); intersection = CCRectMake(fmax(r1.getMinX(),r2.getMinX()), fmax( r1.getMinY(), r2.getMinY()) ,0,0); intersection.size.width = fmin(r1.getMaxX(), r2.getMaxX() - intersection.getMinX()); intersection.size.height = fmin(r1.getMaxY(), r2.getMaxY() - intersection.getMinY()); // Look for simple bounding box collision if ( (intersection.size.width0) && (intersection.size.height0) ) { // If we're not checking for pixel perfect collisions, return true if (!pp) { return true; } unsigned int x = intersection.origin.x; unsigned int y = intersection.origin.y; unsigned int w = intersection.size.width; unsigned int h = intersection.size.height; unsigned int numPixels = w * h; //CCLog("Intersection X and Y %d, %d", x, y); //CCLog("Number of pixels %d", numPixels); // Draw into the RenderTexture _rt-beginWithClear( 0, 0, 0, 0); // Render both sprites: first one in RED and second one in GREEN glColorMask(1, 0, 0, 1); spr1-visit(); glColorMask(0, 1, 0, 1); spr2-visit(); glColorMask(1, 1, 1, 1); // Get color values of intersection area ccColor4B *buffer = (ccColor4B *)malloc( sizeof(ccColor4B) * numPixels ); glReadPixels(x, y, w, h, GL_RGBA, GL_UNSIGNED_BYTE, buffer); _rt-end(); // Read buffer unsigned int step = 1; for(unsigned int i=0; i 0 && color.g 0) { isColliding = true; break; } } // Free buffer memory free(buffer); } return isColliding; } My code is working perfectly if I send the "pp" parameter as false. That is if I do only a bounding box collision but I am not able to get it working correctly for the case when I need Pixel Perfect collision. I think the opengl masking code is not working as I intended. Here is the code for "_rt" _rt = CCRenderTexture::create(visibleSize.width, visibleSize.height); _rt-setPosition(ccp(origin.x + visibleSize.width * 0.5f, origin.y + visibleSize.height * 0.5f)); this-addChild(_rt, 1000000); _rt-setVisible(true); //For testing I think I am making a mistake with the implementation of this CCRenderTexture Can anyone guide me with what I am doing wrong ? Thank you for your time :)

  Read the article

• Using MAC Authentication for simple Web API’s consumption

  - by cibrax

  For simple scenarios of Web API consumption where identity delegation is not required, traditional http authentication schemas such as basic, certificates or digest are the most used nowadays. All these schemas rely on sending the caller credentials or some representation of it in every request message as part of the Authorization header, so they are prone to suffer phishing attacks if they are not correctly secured at transport level with https. In addition, most client applications typically authenticate two different things, the caller application and the user consuming the API on behalf of that application. For most cases, the schema is simplified by using a single set of username and password for authenticating both, making necessary to store those credentials temporally somewhere in memory. The true is that you can use two different identities, one for the user running the application, which you might authenticate just once during the first call when the application is initialized, and another identity for the application itself that you use on every call. Some cloud vendors like Windows Azure or Amazon Web Services have adopted an schema to authenticate the caller application based on a Message Authentication Code (MAC) generated with a symmetric algorithm using a key known by the two parties, the caller and the Web API. The caller must include a MAC as part of the Authorization header created from different pieces of information in the request message such as the address, the host, and some other headers. The Web API can authenticate the caller by using the key associated to it and validating the attached MAC in the request message. In that way, no credentials are sent as part of the request message, so there is no way an attacker to intercept the message and get access to those credentials. Anyways, this schema also suffers from some deficiencies that can generate attacks. For example, brute force can be still used to infer the key used for generating the MAC, and impersonate the original caller. This can be mitigated by renewing keys in a relative short period of time. This schema as any other can be complemented with transport security. Eran Rammer, one of the brains behind OAuth, has recently published an specification of a protocol based on MAC for Http authentication called Hawk. The initial version of the spec is available here. A curious fact is that the specification per se does not exist, and the specification itself is the code that Eran initially wrote using node.js. In that implementation, you can associate a key to an user, so once the MAC has been verified on the Web API, the user can be inferred from that key. Also a timestamp is used to avoid replay attacks. As a pet project, I decided to port that code to .NET using ASP.NET Web API, which is available also in github under https://github.com/pcibraro/hawknet Enjoy!.

  Read the article

• Dell XPS 15 (L502x) sound problem

  - by lauramolenaar

  I have a problem with my sound on my Dell XPS 15. First, when I had Windows 7, my sound was pretty good (I have a JBL 2.1 speaker system with Waves Maxx audio), but since I installed Ubuntu 12.04 it sounded very cheap and as if I put my laptop in a tin can. I've already tried installing alsa-hda-dkms from the alsa-daily ppa (http://ppa.launchpad.net/ubuntu-audio-dev/alsa-daily) This is my audio controller: laura@laura-XPS-L502X:~$ lspci -v | grep -A7 -i audio 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04b6 Flags: bus master, fast devsel, latency 0, IRQ 51 Memory at f1c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel I hope you can help me, and you can always ask me for more information. Result of aplay -l: **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC665 Analog [ALC665 Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 1: ALC665 Digital [ALC665 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 Result of aplay -L: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC665 Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Digital IEC958 (S/PDIF) Digital Audio Output hdmi:CARD=PCH,DEV=0 HDA Intel PCH, HDMI 0 HDMI Audio Output dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample mixing device dmix:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample mixing device dmix:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample snooping device dsnoop:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample snooping device dsnoop:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct hardware device without any conversions hw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct hardware device without any conversions hw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Hardware device with all software conversions plughw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Hardware device with all software conversions plughw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Hardware device with all software conversions

  Read the article

• Exadata support for ACFS (and thus, 10gR2) now available!

  - by Robert Freeman

  Really? Exadata, ACFS and 10gR2? If you work with Exadata you are probably aware that ACFS has not been supported - until now! ACFS is now supported on Exadata if you are running Grid Infrastructure version 12.1.0.2 or later. This new support is described in MOS note 1326938.1. Also Exadata support for ACFS is mentioned in MOS note 888828.1, which is the king of all Exadata notes on MOS. The upshot is that you can now run Oracle Database 10gR2 on Exadata using ACFS as the storage for the Oracle Database. Don’t Over React and just Throw Everything on ACFS!First, let’s be clear that ACFS is not an alternative for running your Exadata databases on ASM. If you are running any production or non-production performance sensitive Oracle databases on 11.2 or 12.1, then you should be running them on ASM disks that are associated with the storage cells. The use case for ACFS is generally limited to the following: Running any Oracle 10gR2 databases on Exadata. Running Oracle 11gR2 development or test databases that require rapid cloning, and that do not require the performance benefits of the Exadata storage cells. If you are running Oracle Database 12c and you need snapshot/clone kinds of capabilities, then you should be using Oracle MultiTennant and the features present in that option (remember though that MultiTennant is a licensed option). The Fine PrintThere are some requirements that you will need to meet If you are going to run ACFS on Exadata. These are: You have to use Oracle Linux You must use GI 12.1.0.2 or later If you wish to use HCC then you must apply the fix for bug 19136936 to your system. This bug, and it’s associated patch do not appear on MOS (as of the time that I wrote this) so you will need to open an SR and get support to provide the patch for you. The Best Use Case for ACFSEven though Oracle Database 10gR2 is at end of life, it remains in use in a large number of places. This has caused problems when choosing to implement Exadata as a consolidation platform, or when choosing it during a hardware refresh process. Now that ACFS is supported, Exadata has become even more flexible and affords customers greater flexibility when migrating to Exadata and Engineered Systems. While all of the features of Exadata might not be available to a 10.2.0.4 database, certainly just the improved processing capabilities of Exadata with its fast as heck infiniband network fabric, additional memory, reduced power requirements and a whole host of other features, justifies moving these databases to Exadata now. This will also make it easier to upgrade these databases when the time comes!

  Read the article

• Not Dead, Just Busy

  - by MOSSLover

  So I didn’t die in a freak smelting accident yet, but I have been dealing with a lot of different things.  I had to take a bit of a break to deal with the cat death issue.  I am not fully recovered, because well it just happened a few months ago.  It kind of sucked.  Plus the apartment feels a lot bigger. Then you have the whole New York Comic Con thing where I had to plan some cosplay costumes.  I have been trying to find time to hang out with friends and have a social life.  That plus I built an entire presentation for iOS development for New York Code Camp.  I am also planning a couple MS Community dinners (namely one a week from Tuesday) plus a give camp.  I am also planning a vacation around SPS UK plus I will be at SPC.  Life is just incredibly hectic and when you factor in dating to the mix it’s gotten insane to the point where some day I just have to go dark.  Hence the lack of blogging.  I am just trying to keep up with everything and everyone without losing myself. If you guys will be at SPC or SPS UK I will be at both places this year.  Stop by the Planet Technologies booth and see me or I’ll be around somewhere.  I am really sorry if I don’t remember you from an event or if you are someone following me on twitter.  I am trying to get better at the mnemonic memory devices, but I think things broke down around the 47th event I attended or spoke at or something to that nature.  If anyone wants to talk to Cathy, Lori, or I about Women in SharePoint definitely find us at the event.  Anyway good night and good luck guys.  I promise to check back at least once before the year ends.  In the meantime twitter stalking is always possible.  Sometimes I even respond back. Technorati Tags: SPC,SPS UK,NYCC,NYC Code Camp,MOSSLover

  Read the article

• Changing the default installation path to a newly installed hard disk

  - by mgj

  Hi, I am currently working on a dual-booted PC. I am using Windows XP and Ubuntu 10.04 Lucid Lynx released in April 2010. The allocated partition to Ubuntu that I am making use of has almost exhausted. Current memory allocations on the PC wrt Ubuntu OS looks like this: bodhgaya@pc146724-desktop:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 8.6G 8.0G 113M 99% / none 998M 268K 998M 1% /dev none 1002M 580K 1002M 1% /dev/shm none 1002M 100K 1002M 1% /var/run none 1002M 0 1002M 0% /var/lock none 1002M 0 1002M 0% /lib/init/rw /dev/sda1 25G 16G 9.8G 62% /media/C /dev/sdb1 37G 214M 35G 1% /media/ubuntulinuxstore bodhgaya@pc146724-desktop:~$ cd /tmp I am trying to mount a 40GB(/dev/sdb1 - given below) new hard disk along with my existing Ubuntu system to overcome with hard disk space related issues. I referred to the following tutorial to mount a new hard disk onto the system:- http://www.smorgasbord.net/how-to-in...untu-linux%20/ I was able to successfully mount this hard disk for Ubuntu 0S. I have this new hard disk setup in /media/ubuntulinuxstore directory. The current partition in my system looks like this: bodhgaya@pc146724-desktop:/media/ubuntulinuxstore$ sudo fdisk -l [sudo] password for bodhgaya: Disk /dev/sda: 40.0 GB, 40000000000 bytes 255 heads, 63 sectors/track, 4863 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x446eceb5 Device Boot Start End Blocks Id System /dev/sda1 * 2 3264 26210047+ 7 HPFS/NTFS /dev/sda2 3265 4385 9004432+ 83 Linux /dev/sda3 4386 4863 3839535 82 Linux swap / Solaris Disk /dev/sdb: 40.0 GB, 40000000000 bytes 255 heads, 63 sectors/track, 4863 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xfa8afa8a Device Boot Start End Blocks Id System /dev/sdb1 1 4862 39053983+ 7 HPFS/NTFS bodhgaya@pc146724-desktop:/media/ubuntulinuxstore$ Now, I have a concern wrt the "location" where the new softwares will be installed. Generally softwares are installed via the terminal and by default a fixed path is used to where the post installation set up files can be found (I am talking in context of the drive). This is like the typical case of Windows, where softwares by default are installed in the C: drive. These days people customize their installations to a drive which they find apt to serve their purpose (generally based on availability of hard disk space). I am trying to figure out how to customize the same for Ubuntu. As we all know the most softwares are installed via commands given from the Terminal. My road block is how do I redirect the default path set on the terminal where files get installed to this new hard disk. This if done will help me overcome space constraints I am currently facing wrt the partition on which my Ubuntu is initially installed. I would also by this, save time on not formatting my system and reinstalling Ubuntu and other softwares all over again. Please help me with this, your suggestions are much appreciated.

  Read the article

• XMPP— openfire,PHP and python web service

  - by mlakhara

  I am planning to integrate real time notifications into a web application that I am currently working on. I have decided to go with XMPP for this and selected openfire server which i thought to be suitable for my needs. The front end uses strophe library to fetch the notifications using BOSH from my openfire server. However the notices are the notifications and other messages are to be posted by my application and hence I think this code needs to reside at the backend. Initially I thougt of going with PHP XMPP libraries like XMPHP and JAXL but then I think that this would cause much overhead as each script will have to do same steps like connection, authentication etc. and I think this would make the PHP end a little slow and unresponsive. Now I am thinking of creating a middle-ware application acting as a web service that the PHP will call and this application will handle the stuff with XMPP service. The benefit with this is that this app(a server if you will) will have to connect just once and the it will sit there listening on a port. also I am planning to build it in a asynchronous way such that It will first take all the requests from my PHp app and then when there are no more requests; go about doing the notification publishing stuff. I am planninng to create this service in Python using SleekXMPP. This is just what I planned. I am new to XMPP and this whole web service stuff ans would like to take your comments on this regarding issues like memory and CPU usage, advantages, disadvantages, scalability issues,security etc. Thanks in advance. PS:-- also if something like this already exists(although I didn't find after a lot of Googling) Please direct me there. EDIT --- The middle-level service should be doing the following(but not limited to): 1. Publishing notifications for different level of groups and community pages. 2. Notification for single user on some event. 3. User registration(can be done using user service plugin though). EDIT --- Also it should like to create pub-sub nodes and subscribe and unsubscribe users from these pub-sub nodes. Also I want to store the notifications and messages in a database(openfire doesn't). Would that be a good choice?

  Read the article

• Clone a Hard Drive Using an Ubuntu Live CD

  - by Trevor Bekolay

  Whether you’re setting up multiple computers or doing a full backup, cloning hard drives is a common maintenance task. Don’t bother burning a new boot CD or paying for new software – you can do it easily with your Ubuntu Live CD. Not only can you do this with your Ubuntu Live CD, you can do it right out of the box – no additional software needed! The program we’ll use is called dd, and it’s included with pretty much all Linux distributions. dd is a utility used to do low-level copying – rather than working with files, it works directly on the raw data on a storage device. Note: dd gets a bad rap, because like many other Linux utilities, if misused it can be very destructive. If you’re not sure what you’re doing, you can easily wipe out an entire hard drive, in an unrecoverable way. Of course, the flip side of that is that dd is extremely powerful, and can do very complex tasks with little user effort. If you’re careful, and follow these instructions closely, you can clone your hard drive with one command. We’re going to take a small hard drive that we’ve been using and copy it to a new hard drive, which hasn’t been formatted yet. To make sure that we’re working with the right drives, we’ll open up a terminal (Applications > Accessories > Terminal) and enter in the following command sudo fdisk –l We have two small drives, /dev/sda, which has two partitions, and /dev/sdc, which is completely unformatted. We want to copy the data from /dev/sda to /dev/sdc. Note: while you can copy a smaller drive to a larger one, you can’t copy a larger drive to a smaller one with the method described below. Now the fun part: using dd. The invocation we’ll use is: sudo dd if=/dev/sda of=/dev/sdc In this case, we’re telling dd that the input file (“if”) is /dev/sda, and the output file (“of”) is /dev/sdc. If your drives are quite large, this can take some time, but in our case it took just less than a minute. If we do sudo fdisk –l again, we can see that, despite not formatting /dev/sdc at all, it now has the same partitions as /dev/sda.  Additionally, if we mount all of the partitions, we can see that all of the data on /dev/sdc is now the same as on /dev/sda. Note: you may have to restart your computer to be able to mount the newly cloned drive. And that’s it…If you exercise caution and make sure that you’re using the right drives as the input file and output file, dd isn’t anything to be scared of. Unlike other utilities, dd copies absolutely everything from one drive to another – that means that you can even recover files deleted from the original drive in the clone! Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDHow to Browse Without a Trace with an Ubuntu Live CDRecover Deleted Files on an NTFS Hard Drive from a Ubuntu Live CDCreate a Bootable Ubuntu 9.10 USB Flash DriveWipe, Delete, and Securely Destroy Your Hard Drive’s Data the Easy Way TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos Video preview of new Windows Live Essentials 21 Cursor Packs for XP, Vista & 7

  Read the article

• Bancassurers Seek IT Solutions to Support Distribution Model

  - by [email protected]

  Oracle Insurance's director of marketing for EMEA, John Sinclair, attended the third annual Bancassurance Forum in Vienna last month. He reports that the outlook for bancassurance in EMEA remains positive, despite changing market conditions that have led a number of bancassurers to re-examine their business models. Vienna is at the crossroads between mature Western European markets, where bancassurance is now an established best practice, and more recently tapped Eastern European markets that offer the greatest growth potential. Attendance at the Bancassurance Forum was good, with 87 bancassurance attendees, most in very senior positions in the industry. The conference provided the chance for a lively discussion among bancassurers looking to keep abreast of the latest trends in one of Europe's most successful distribution models for insurance. Even under normal business conditions, there is a great demand for best practice sharing within the industry as there is no standard formula for success.  Each company has to chart its own course and choose the strategies for sales, products development and the structure of ownership that make sense for their business, and as soon as they get it right bancassurers need to adapt the mix to keep up with ever changing regulations, completion and economic conditions.  To optimize the overall relationship between banking and insurance for mutual benefit, a balance needs to be struck between potentially conflicting interests. The banking side of the house is looking for greater wallet share from its customers and the ability to increase profitability by bundling insurance products with higher margins - especially in light of the recent economic crisis, where margins for traditional banking products are low and completion high. The insurance side of the house seeks access to new customers through a complementary distribution channel that is efficient and cost effective. To make the relationship work, it is important that both sides of the same house forge strategic and long term relationships - irrespective of whether the underlying business model is supported by a distribution agreement, cross-ownership or other forms of capital structure. However, this third annual conference was not held under normal business conditions. The conference took place in challenging, yet interesting times. ING's forced spinoff of its insurance operations under pressure by the EU Commission and the troubling losses suffered by Allianz as a result of the Dresdner bank sale were fresh in everyone's mind. One year after markets crashed, there is now enough hindsight to better understand the implications for bancassurance and best practices that are emerging to deal with them. The loan-driven business that has been crucial to bancassurance up till now evaporated during the crisis, leaving bancassurers grappling with how to change their overall strategy from a loan-driven to a more diversified model.  Attendees came to the conference to learn what strategies were working - not only to cope with the market shift, but to take advantage of it as markets pick up. Over the course of 14 customer case studies and numerous analyst presentations, topical issues ranging from getting the business model right to the impact on capital structuring of Solvency II were debated openly. Many speakers alluded to the need to specifically design insurance products with the banking distribution channel in mind, which brings with it specific requirements such as a high degree of standardization to achieve efficiency and reduce training costs. Moreover, products must be engineered to suit end consumers who consider banks a one-stop shop. The importance of IT to the successful implementation of bancassurance strategies was a theme that surfaced regularly throughout the conference.  The cross-selling opportunity - that will ultimately determine the success or failure of any bancassurance model - can only be fully realized through a flexible IT architecture that enables banking and insurance processes to be integrated and presented to front-line staff through a common interface. However, the reality is that most bancassurers have legacy IT systems, which constrain the businesses' ability to implement new strategies to maintaining competitiveness in turbulent times. My colleague Glenn Lottering, who chaired the conference, believes that the primary opportunities for bancassurers to extract value from their IT infrastructure investments lie in distribution management, risk management with the advent of Solvency II, and achieving operational excellence. "Oracle is ideally suited to meet the needs of bancassurance," Glenn noted, "supplying market-leading software for both banking and insurance. Oracle provides adaptive systems that let customers easily integrate hybrid business processes from both worlds while leveraging existing IT infrastructure." Overall, the consensus at the conference was that the outlook for bancassurance in EMEA remains positive, despite changing market conditions that have led a number of bancassurers to re-examine their business models. John Sinclair is marketing director for Oracle Insurance in EMEA. He has more than 20 years of experience in insurance and financial services.    

  Read the article

• Anticipating JavaOne 2012 – Number 17!

  - by Janice J. Heiss

  As I write this, JavaOne 2012 (September 30-October 4 in San Francisco, CA) is just over a week away -- the seventeenth JavaOne! I’ll resist the impulse to travel in memory back to the early days of JavaOne. But I will say that JavaOne is a little like your birthday or New Year’s in that it invites reflection, evaluation, and comparison. It’s a time when we take the temperature of Java and assess the world of information technology generally. At JavaOne, insight and information flow amongst Java developers like no other time of the year.This year, the status of Java seems more secure in the eyes of most Java developers who agree that Oracle is doing an acceptable job of stewarding the platform, and while the story is still in progress, few doubt that Oracle is engaging strongly with the Java community and wants to see Java thrive. From my perspective, the biggest news about Java is the growth of some 250 alternative languages for the JVM – from Groovy to Jython to JRuby to Scala to Clojure and on and on – offering both new opportunities and challenges. The JVM has proven itself to be unusually flexible, resulting in an embarrassment of riches in which, more and more, developers are challenged to find ways to optimally mix together several different languages on projects.    To the matter at hand -- I can say with confidence that Oracle is working hard to make each JavaOne better than the last – more interesting, more stimulating, more networking, and more fun! A great deal of thought and attention is being devoted to the task. To free up time for the 475 technical sessions/Birds of feather/Hands-on-Labs slots, the Java Strategy, Partner, and Technical keynotes will be held on Sunday September 30, beginning at 4:00 p.m.   Let’s not forget Java Embedded@JavaOne which is being held Wednesday, Oct. 3rd and Thursday, Oct. 4th at the Hotel Nikko. It will provide business decision makers, technical leaders, and ecosystem partners important information about Java Embedded technologies and new business opportunities.   This year's JavaOne theme is “Make the Future Java”. So come to JavaOne and make your future better by:--Choosing from 475 sessions given by the experts to improve your working knowledge and coding expertise --Networking with fellow developers in both casual and formal settings--Enjoying world-class entertainment--Delighting in one of the world’s great cities (my home town) Hope to see you there!

  Read the article

• Web application / Domain model integration using JSON capable DTOs [on hold]

  - by g-makulik

  I'm a bit confused about architectural choices for the web-applications/java/python world. For c/c++ world the available (open source) choices to implement web applications is pretty limited to zero, involving java or python the choices explode to a,- hard to sort out -, mess of available 'frameworks' and application approaches. I want to sort out a clean MVC model, where the M stands for a fully blown (POCO, POJO driven) domain model (according M.Fowler's EAA pattern) using a mature OO language (Java,C++) for implementation. The background is: I have a system with certain hardware components (that introduce system immanent active behavior) and a configuration database for system meta and HW-components configuration data (these are even usually self contained, since the HW-components are capable to persist their configuration data anyway). For realization of the configuration/status data exchange protocol with the HW-components we have chosen the Google Protobuf format, which works well for the directly wired communication with these components. This protocol is already used successfully with a Java based GUI application via TCP/IP connection to the main system controlling HW-component. This application has some drawbacks and design flaws for historical reasons. Now we want to develop an abstract model (domain model) for configuration and monitoring those HW-components, that represents a more use case oriented view to the overall system behavior. I have the feeling that a plain Java class model would fit best for this (c++ implementation seems to have too much implementation/integration overhead with viable language-bridge interfaces). Google Protobuf message definitions could still serve well to describe DTO objects used to interact with a domain model API. But integrating Google Protobuf messages client side for e.g. data binding in the current view doesn't seem to be a good choice. I'm thinking about some extra serialization features, e.g. for JSON based data exchange with the views/controllers. Most lightweight solutions seem to involve a python based presentation layer using JSON based data transfer (I'm at least not sure to be fully informed about this). Is there some lightweight (applicable for a limited ARM Linux platform) framework available, supporting such architecture to realize a web-application? UPDATE: According to my recent research and comments of colleagues I've noticed that using Java (and some JVM) might not be the preferable choice for integration with python on a limited linux system as we have (running on ARM9 with hard to discuss memory and MCU costs), but C/C++ modules would do well for this (since this forms the native interface to python extensions, doesn't it?). I can imagine to provide a domain model from an appropriate C/C++ API (though I still think it's more efforts and higher skill requirements for the involved developers to do with these languages). Still I'm searching for a good approach that supports such architecture. I'll appreciate any pointers!

  Read the article

• Make the Firefox Awesome Bar Semi-Transparent Like Google Chrome

  - by Matthew Guay

  Would you like to make the Firefox Awesome Bar drop-down menu semi-transparent like in Google Chrome?  Here’s a quick trick that can make your Firefox Awesome Bar a bit more awesome. When you type an address or search query into the address bar in Google Chrome, the drop-down list of history and search suggestions that appears is slightly transparent.  Nothing extreme, but it adds a nice touch. Firefox’s Awesome bar, on the other hand, is fully opaque by default. We can change that with a simple change.  Exit Firefox, then open your Firefox profile folder by entering the following in the address bar in Explorer or in the Run command: %appdata%\Mozilla\Firefox\Profiles\ Open the default folder, and then open the Chrome folder in it. Now, open the userChrome.css file in an editor such as Notepad.  If you do not have a userChrome.css file, open the userChrome-example.css file instead. Now, add the following to the end of the file: #PopupAutoCompleteRichResult[type="autocomplete-richlistbox"]{    opacity: 0.9 !important;} You can change the opacity value, but 0.9 seemed the closest to Chrome’s transparency while keeping the text readable. Save the file as userChrome.css in that same folder.  If you’re editing with Notepad, make sure to select to save as All Files so the file won’t be saved with a .txt extension. Open Firefox, and now your Awesome Bar’s drop-down list will be transparent.  Actually, it may look even more awesome than Google Chrome’s address bar! Conclusion With this simple trick, you can make your Firefox Awesome bar a bit more awesome.  With tweaks like this, it’s no wonder Firefox is still so popular. Special thanks to Daniel Spiewak for the tip! Similar Articles Productive Geek Tips Stupid Geek Tricks: Compare Your Browser’s Memory Usage with Google ChromeHow to Make Google Chrome Your Default BrowserEnable Vista Black Style Theme for Google Chrome in XPMake your Gnome Terminal Background (mostly)Transparent on UbuntuStop YouTube Videos from Automatically Playing in Chrome TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 Use ILovePDF To Split and Merge PDF Files TimeToMeet is a Simple Online Meeting Planning Tool Easily Create More Bookmark Toolbars in Firefox Filevo is a Cool File Hosting & Sharing Site Get a free copy of WinUtilities Pro 2010 World Cup Schedule

  Read the article

• Oracle Data Integration 12c: Simplified, Future-Ready, High-Performance Solutions

  - by Thanos Terentes Printzios

  In today’s data-driven business environment, organizations need to cost-effectively manage the ever-growing streams of information originating both inside and outside the firewall and address emerging deployment styles like cloud, big data analytics, and real-time replication. Oracle Data Integration delivers pervasive and continuous access to timely and trusted data across heterogeneous systems. Oracle is enhancing its data integration offering announcing the general availability of 12c release for the key data integration products: Oracle Data Integrator 12c and Oracle GoldenGate 12c, delivering Simplified and High-Performance Solutions for Cloud, Big Data Analytics, and Real-Time Replication. The new release delivers extreme performance, increase IT productivity, and simplify deployment, while helping IT organizations to keep pace with new data-oriented technology trends including cloud computing, big data analytics, real-time business intelligence. With the 12c release Oracle becomes the new leader in the data integration and replication technologies as no other vendor offers such a complete set of data integration capabilities for pervasive, continuous access to trusted data across Oracle platforms as well as third-party systems and applications. Oracle Data Integration 12c release addresses data-driven organizations’ critical and evolving data integration requirements under 3 key themes: Future-Ready Solutions : Supporting Current and Emerging Initiatives Extreme Performance : Even higher performance than ever before Fast Time-to-Value : Higher IT Productivity and Simplified Solutions  With the new capabilities in Oracle Data Integrator 12c, customers can benefit from: Superior developer productivity, ease of use, and rapid time-to-market with the new flow-based mapping model, reusable mappings, and step-by-step debugger. Increased performance when executing data integration processes due to improved parallelism. Improved productivity and monitoring via tighter integration with Oracle GoldenGate 12c and Oracle Enterprise Manager 12c. Improved interoperability with Oracle Warehouse Builder which enables faster and easier migration to Oracle Data Integrator’s strategic data integration offering. Faster implementation of business analytics through Oracle Data Integrator pre-integrated with Oracle BI Applications’ latest release. Oracle Data Integrator also integrates simply and easily with Oracle Business Analytics tools, including OBI-EE and Oracle Hyperion. Support for loading and transforming big and fast data, enabled by integration with big data technologies: Hadoop, Hive, HDFS, and Oracle Big Data Appliance. Only Oracle GoldenGate provides the best-of-breed real-time replication of data in heterogeneous data environments. With the new capabilities in Oracle GoldenGate 12c, customers can benefit from: Simplified setup and management of Oracle GoldenGate 12c when using multiple database delivery processes via a new Coordinated Delivery feature for non-Oracle databases. Expanded heterogeneity through added support for the latest versions of major databases such as Sybase ASE v 15.7, MySQL NDB Clusters 7.2, and MySQL 5.6., as well as integration with Oracle Coherence. Enhanced high availability and data protection via integration with Oracle Data Guard and Fast-Start Failover integration. Enhanced security for credentials and encryption keys using Oracle Wallet. Real-time replication for databases hosted on public cloud environments supported by third-party clouds. Tight integration between Oracle Data Integrator 12c and Oracle GoldenGate 12c and other Oracle technologies, such as Oracle Database 12c and Oracle Applications, provides a number of benefits for organizations: Tight integration between Oracle Data Integrator 12c and Oracle GoldenGate 12c enables developers to leverage Oracle GoldenGate’s low overhead, real-time change data capture completely within the Oracle Data Integrator Studio without additional training. Integration with Oracle Database 12c provides a strong foundation for seamless private cloud deployments. Delivers real-time data for reporting, zero downtime migration, and improved performance and availability for Oracle Applications, such as Oracle E-Business Suite and ATG Web Commerce . Oracle’s data integration offering is optimized for Oracle Engineered Systems and is an integral part of Oracle’s fast data, real-time analytics strategy on Oracle Exadata Database Machine and Oracle Exalytics In-Memory Machine. Oracle Data Integrator 12c and Oracle GoldenGate 12c differentiate the new offering on data integration with these many new features. This is just a quick glimpse into Oracle Data Integrator 12c and Oracle GoldenGate 12c. Find out much more about the new release in the video webcast "Introducing 12c for Oracle Data Integration", where customer and partner speakers, including SolarWorld, BT, Rittman Mead will join us in launching the new release. Resource Kits Meet Oracle Data Integration 12c  Discover what's new with Oracle Goldengate 12c  Oracle EMEA DIS (Data Integration Solutions) Partner Community is available for all your questions, while additional partner focused webcasts will be made available through our blog here, so stay connected. For any questions please contact us at partner.imc-AT-beehiveonline.oracle-DOT-com Stay Connected Oracle Newsletters

  Read the article

• Common business drivers that lead to creating and sustaining a project

  Common business drivers that lead to creating and sustaining a project include and are not limited to: cost reduction, increased return on investment (ROI), reduced time to market, increased speed and efficiency, increased security, and increased interoperability. These drivers primarily focus on streamlining and reducing cost to make a company more profitable with less overhead. According to Answers.com cost reduction is defined as reducing costs to improve profitability, and may be implemented when a company is having financial problems or prevent problems. ROI is defined as the amount of value received relative to the amount of money invested according to PayperclickList.com.  With the ever increasing demands on businesses to compete in today’s market, companies are constantly striving to reduce the time it takes for a concept to become a product and be sold within the global marketplace. In business, some people say time is money, so if a project can reduce the time a business process takes it in fact saves the company which is always good for the bottom line. The Social Security Administration states that data security is the protection of data from accidental or intentional but unauthorized modification, destruction. Interoperability is the capability of a system or subsystem to interact with other systems or subsystems. In my personal opinion, these drivers would not really differ for a profit-based organization, compared to a non-profit organization. Both corporate entities strive to reduce cost, and strive to keep operation budgets low. However, the reasoning behind why they want to achieve this does contrast. Typically profit based organizations strive to increase revenue and market share so that the business can grow. Alternatively, not-for-profit businesses are more interested in increasing their reach within communities whether it is to increase annual donations or invest in the lives of others. Success or failure of a project can be determined by one or more of these drivers based on the scope of a project and the company’s priorities associated with each of the drivers. In addition, if a project attempts to incorporate multiple drivers and is only partially successful, then the project might still be considered to be a success due to how close the project was to meeting each of the priorities. Continuous evaluation of the project could lead to a decision to abort a project, because it is expected to fail before completion. Evaluations should be executed after the completion of every software development process stage. Pfleeger notes that software development process stages include: Requirements Analysis and Definition System Design Program Design Program Implementation Unit Testing Integration Testing System Delivery Maintenance Each evaluation at every state should consider all the business drivers included in the scope of a project for how close they are expected to meet expectations. In addition, minimum requirements of acceptance should also be included with the scope of the project and should be reevaluated as the project progresses to ensure that the project makes good economic sense to continue. If the project falls below these benchmarks then the project should be put on hold until it does make more sense or the project should be aborted because it does not meet the business driver requirements.   References Cost Reduction Program. (n.d.). Dictionary of Accounting Terms. Retrieved July 19, 2009, from Answers.com Web site: http://www.answers.com/topic/cost-reduction-program Government Information Exchange. (n.d.). Government Information Exchange Glossary. Retrieved July 19, 2009, from SSA.gov Web site: http://www.ssa.gov/gix/definitions.html PayPerClickList.com. (n.d.). Glossary Term R - Pay Per Click List. Retrieved July 19, 2009, from PayPerClickList.com Web site: http://www.payperclicklist.com/glossary/termr.html Pfleeger, S & Atlee, J.(2009). Software Engineering: Theory and Practice. Boston:Prentice Hall Veluchamy, Thiyagarajan. (n.d.). Glossary « Thiyagarajan Veluchamy’s Blog. Retrieved July 19, 2009, from Thiyagarajan.WordPress.com Web site: http://thiyagarajan.wordpress.com/glossary/

  Read the article

• mysql completely removing

  - by Dmitry Teplyakov

  I broke my mysql and now I want to completely reinstall it. I tried: $ sudo apt-get install --reinstall mysql-server $ sudo apt-get remove --purge mysql-client mysql-server But always I see popup with proposal to change root password, I change it and got an error that I can change it.. $ sudo apt-get remove --purge mysql-client mysql-server Reading package lists... Done Building dependency tree Reading state information... Done Package mysql-client is not installed, so not removed Package mysql-server is not installed, so not removed The following packages were automatically installed and are no longer required: libmygpo-qt1 libqtscript4-network libqtscript4-gui libtag-extras1 libqtscript4-sql libqtscript4-xml amarok-utils amarok-common libqtscript4-uitools liblastfm0 libloudmouth1-0 libqtscript4-core Use 'apt-get autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up mysql-server-5.5 (5.5.28-0ubuntu0.12.04.2) ... 121114 19:04:03 [Note] Plugin 'FEDERATED' is disabled. 121114 19:04:03 InnoDB: The InnoDB memory heap is disabled 121114 19:04:03 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121114 19:04:03 InnoDB: Compressed tables use zlib 1.2.3.4 121114 19:04:03 InnoDB: Initializing buffer pool, size = 128.0M 121114 19:04:03 InnoDB: Completed initialization of buffer pool InnoDB: Error: auto-extending data file ./ibdata1 is of a different size InnoDB: 0 pages (rounded down to MB) than specified in the .cnf file: InnoDB: initial 640 pages, max 0 (relevant if non-zero) pages! 121114 19:04:03 InnoDB: Could not open or create data files. 121114 19:04:03 InnoDB: If you tried to add new data files, and it failed here, 121114 19:04:03 InnoDB: you should now edit innodb_data_file_path in my.cnf back 121114 19:04:03 InnoDB: to what it was, and remove the new ibdata files InnoDB created 121114 19:04:03 InnoDB: in this failed attempt. InnoDB only wrote those files full of 121114 19:04:03 InnoDB: zeros, but did not yet use them in any way. But be careful: do not 121114 19:04:03 InnoDB: remove old data files which contain your precious data! 121114 19:04:03 [ERROR] Plugin 'InnoDB' init function returned error. 121114 19:04:03 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 121114 19:04:03 [ERROR] Unknown/unsupported storage engine: InnoDB 121114 19:04:03 [ERROR] Aborting 121114 19:04:03 [Note] /usr/sbin/mysqld: Shutdown complete start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: mysql-server-5.5 E: Sub-process /usr/bin/dpkg returned an error code (1) It is good for me that I have not any important databases, but..

  Read the article

• Playing NSF music in FMOD.net

  - by Tesserex

  So, as the title says, I want to be able to play NSF files using FMOD, because my project already uses FMOD and I'd rather not replace it. This will involve figuring out how existing players and emulators work and porting it. I haven't yet found an existing player that uses FMOD. My starting point is the MyNes source from http://sourceforge.net/projects/mynes/. There are two big steps between here and what I'm looking for. MyNes plays from a ROM, not NSF. So, I have to rip out the APU and get it to play NSF files. The MyNes APU uses SlimDX, so I have to convert that to FMOD.NET. I am really stuck about how to go about either of these, because I'm not that familiar with audio formats and it's hard finding resources online. So here are a few questions: From what I can tell from the NSF spec at http://kevtris.org/nes/nsfspec.txt, it's just contains the relevant memory section of the ROM, plus the header. If anyone can verify or correct this that would be great. The emulator APU uses data from the rest of the emulator to play, including things like cycle counts. I'm not sure what replaces this in a standalone player. Can't I just load all the music data at once into a stream and play it? Joining #1 and #2, does the header data from the NSF substitute for some of the ROM data in the emulator code? Using FMOD, will I be following the usercreatedsound example for loading a stream? And does this format count as PCM? Specifically MyNes says PCM8. Any tips on loading / playing the stream in FMOD are appreciated. As an aside, I don't really understand the loading / playing sections of the spec I linked at all. It seems to apply to 6502 systems / emulators only and not to my situation. I know it's a long shot for anyone here to have enough experience in this area to help, but anything you can provide is definitely appreciated. A link to an existing .NET library that does this would be even better, but I don't believe one exists.

  Read the article

• Gain Quick Access to the Cache in Firefox

  - by Asian Angel

  Are you looking for a quick and simple way to view the contents of the cache in Firefox? Then you will definitely want to see how easy it can be using the CacheViewer extension. Note: CacheViewer is a front-end app for easily accessing and searching the memory cache. Before Viewing the cache in Firefox using “about:cache” provides some information about the contents but may not be the most efficient method available for some people. CacheViewer in Action Once you have installed the extension there are three easy ways to access your new cache viewer. The first is using the “CacheViewer Command” available in the “Tools Menu” and the second is using the keyboard shortcut “Ctrl + Shift + C”. The third way is by adding a “Toolbar Button” to your browser’s UI. All three work equally well…choose the method that best suits your personal needs. When you access the “CacheViewer Window” this is what it will look like. You may decide to resize it and move (or hide) some of the columns for the best viewing. You can easily scroll through the cache contents and preview images if desired as shown here. If you keep the “CacheViewer Window” open you can refresh it as you browse using the “Refresh Button” in the lower right corner. This is a nice, quick, and very simple way to access the cache on demand and save items to your hard-drive if desired. Note: The “CacheViewer” can also be set to open in a new tab instead (see “Options”). Options Choose whether “CacheViewer” opens in a separate window (default) or in a new tab. Conclusion If you want a quick and simple way to view the cache in Firefox then the CacheViewer extension is just what you have been looking for. Link Download the CacheViewer extension (Mozilla Add-ons) Similar Articles Productive Geek Tips Add a Cache Clearing Button to FirefoxSearch for Install Packages from the Ubuntu Command LineQuick Tip: Empty Internet Explorer 7 Cache when Browser is ClosedView Internet Explorer Cache Files the Easy WayQuick Hits: 11 Firefox Tab How-Tos TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows SyncToy syncs Files and Folders across Computers on a Network (or partitions on the same drive) If it were only this easy Classic Cinema Online offers 100’s of OnDemand Movies OutSync will Sync Photos of your Friends on Facebook and Outlook

  Read the article

< Previous Page | 505 506 507 508 509 510 511 512 513 514 515 516  | Next Page >