Search Results

Search found 26798 results on 1072 pages for 'difference between detach attach and restore backup a db'.

Page 515/1072 | < Previous Page | 511 512 513 514 515 516 517 518 519 520 521 522  | Next Page >

• D-Link DIR-300 slows down / loses network

  - by basic6

  there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• Best way to reformat/recover in Windows when your CD key is no longer valid?

  - by CSarnia

  I have a copy of Windows 7 Professional that I have downloaded from the MSDN e-academy (thanks to my school). Now, the problem is that these license keys are one-use only. If I need to reformat or do a factory reset, what is the best way for me to do so, without invalidating my license and screwing me out of an operating system? Edit: I would also like to know some information on the "restore to factory settings" option in Windows 7 recovery center. Does it do exactly as the name implies and starts you off as if you had just done a fresh install? If I had some kind of nasty trojan or virus, would it be able to survive through the factory reset? The recovery center also has an option for reformatting, though I don't think that it's an actual format - it just backs up your stuff into a Windows.old folder or something like that. Does that require a valid license key?

  Read the article

• nslookup gives wrong ip for my domain

  - by Werulz

  I am having some problem in trying to setup DNS for my domain on my server. This tutorial normally works fine for me but when i tried to lookup my domain it gives the following output Server: 4.2.2.1 Address: 4.2.2.1#53 Non-authoritative answer: 119.100.79.64.in-addr.arpa name = server.leech4ever.com. Authoritative answers can be found from: The server and the address are wrong according to the tutorial Here is tutorial http://webcache.googleusercontent.com/search?q=cache:rR7Z4YU4GI0J:www.broexperts.com/2012/03/linux-dns-bind-configuration-on-centos-6-2/+broexperts+bind&cd=1&hl=en&ct=clnk&gl=mu /etc/hosts 127.0.0.1 localhost 64.79.100.119 server.leech4ever.com server /etc/resolve.conf search leech4ever.com nameserver 64.79.100.119 /etc/resolv.conf nameserver 4.2.2.1 nameserver 4.2.2.2 How to solve this problem guys.....The tutorial was flawless until i did a server restore

  Read the article

• Unable to change IP address for eth0 without restart in Ubuntu

  - by Rodnower

  I have Ubuntu 12.04.1 installed. I tried to change the IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4 auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status When I issue: sudo service networking restart I get this response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart does the IP change. Any ideas?

  Read the article

• Upgrade no raid server to raid

  - by AZee

  I have just learned that our PDC has a single drive with 2 partitions. I also know that this drive has bad blocks as recorded in the event log. What I would like to do is to convert this to a RAID solution with a nice balance between economy and performance. I will admit that I have only configured servers with RAID from scratch, and have no experience upgrading an existing system into a RAID system. In fact, I'm not sure it is even possible. Since this is the PDC for 350+ workstations downtime is important. I'd like to hear from other System Administators how they would tackle this and their recommendations for all devices. At this time it seems to me that I can replace the existing drive and then restore from backup or install a controller, drives, configure the RAID an basically start from scratch. Thank you for taking your time. ~AZee

  Read the article

• How do I mirror a MySQL database?

  - by user45745

  I'm running two load balanced servers for one website, and I'd like the databases to be synchronized. Queries may be run on either of the two servers because they are both production sites, so the replication can't just work one way. It doesn't have to be in real-time, just fairly accurate so people don't notice a difference when they get switched to a different server.

  Read the article

• After making boot disk using rufus in usb 3.0 port, it doesn't work in another ports.

  - by sin

  I have a big problem! After making boot disk using rufus in usb 3.0 port, it doesn't work in another ports. I have to install windows in other PC which has usb 2.0port only! so I made usb booting disk using usb 3.0 in 3.0 port. but after that it never worked except in 3.0 ... and I could't restore my usb. I alredy fomated in cmd and others in usb3.0 port! but there is no change. and I couldn't find it in usb 2.0 port. plz help me.

  Read the article

• Linux RAID0 - relocating member disk

  - by qdot

  I've got an issue I would rather handle with the array online - I am using RAID0 for temporary video storage - data that is low-cost to restore, but that is used frequently. The software array looks like this: md1 : active raid0 sdb1[2] sdc1[3] sdd1[0] sde1[1] 1953487616 blocks 64k chunks I have another partition (sda1) in this system, that I want to use to replace sdc1 (The drives are of varying age, and sdc1 is definitely the slowest one, limiting the entire array's sequential read performance to only 300MB/s). Is there a way to migrate the data from sdc1 to sda1 while the array is still online?

  Read the article

• Sharepoint 2010 moving site collection to different database error

  - by Brandon Ulasiewicz

  I am trying to move a site collection from one content database to another content database. First I used the following PowerShell command: New-SPContentDatabase -Name New_DB -WebApplication http://portal/ I confirmed that this did in fact create the DB in the SQL Server. I then used the following command: Move-SPSite http://portal/sites/hr -DestinationDatabase New_DB This generates an error stating that the "Operation is not valid due to the current state of the object" Can anyone help point me in the right direction with this? Thanks

  Read the article

• TFT vs XWGA, WSVGA

  - by doug

  hi there I'm looking for a netbook, but i really don't know which is the difference between those technologies. Which is the best for outdoor use of a netbook?

  Read the article

• Windows 7 freezes on boot screen

  - by this is a dead end

  There was some update that required me to restart my computer, so I did. when it restarted, it stays at the Windows boot screen forever, the screen that says "Starting Windows" and has that Windows logo in the middle. I've tried the start up repair program that shows up when I click F8 when the computer starts. And tried system restore but, it says it has restored windows successfully but it still freezes on the boot screen when I reboot it. When I try starting it in safe mode, it gets to the blue Windows background, the one with the logon screen, then says "Failure configuring Windows updates. Reverting Changes. Do not turn off." Then after a while it reboot by itself. Just noticed, the logo animation on the boot screen is still animated. So it's not completely frozen.

  Read the article

• Easiest way to move my Windows installation to an SSD?

  - by Jon Artus

  I've taken the plunge and bought an SSD and want to move my existing Windows installation over. The current hard disk is 500Gb, but I've trimmed the contents down to about ~40Gb. I'm transferring it across to a 100Gb SSD and looking for the easiest way just to copy everything across and set the SSD up as a boot device. I've looked at a few tools like Macrium Reflect, but they don't seem able to restore to a smaller drive. Do I need to go for something like PING to do this? I'm trying to avoid scary Linux-based boot utilities if possible, does anyone know of an easier way?

  Read the article

• Manually forcing TCP connection to retry

  - by Vi.

  I have a TCP connection (SSH session to some computer for example) Network suddenly goes down and drops all packets (disconnected cable, out of range). TCP resends packets again and again, retrying with increasing delays. I see the problem and plug the cable back (or restore network somehow). TCP connection finally successfully resends some packet and continues. The problem is that I need to wait for a some timeout on point 5. I want to use my opened SSH session now and not wait for 5-10 seconds until it finds out that connection is working again. How to force all TCP connections to resend data without delays in GNU/Linux?

  Read the article

• How does google maps know my current location on my iTouch?

  - by Tommy

  Using only my home wi-fi, how is google maps able to locate my current position? I know the device doesn't have gps. Also no cellular data to triangulate. I read about skyhook that has a db of popular wifi hot spots but I doubt my house is listed. Any information is appreciated. Thanks

  Read the article

• localhost as hostname confusion [duplicate]

  - by Baboon

  This question already has an answer here: localhost as hostname confusion 1 answer I have a basic understanding about hostname and FQDN. Now I am confused, do I really have to specify a name for my hostname? So for example: Hostname: somename Domain: mydomain.com FQDN: somename.mydomain.com Now, I see something that the hostname is localhost. What is the difference and impact of that? So my FQDN if localhost is my hostname would be localhost.mydomain.com, right?

  Read the article

• Apache Issues on Windows Server 2008

  - by dlackey

  I'm looking to reinstall Apache 2.2.25 since I continue to get these errors in the Windows Application log every 2-5 minutes: Faulting application name: httpd.exe, version: 2.2.25.0, time stamp: 0x51dd049c Faulting module name: zlib1.dll, version: 1.2.3.0, time stamp: 0x4790446a Exception code: 0xc0000005 Fault offset: 0x00002bad Faulting process id: 0x38e8 Faulting application start time: 0x01cfbfd70cdfbc4f Faulting application path: C:\Apache2\bin\httpd.exe Faulting module path: C:\Apache2\bin\zlib1.dll Report Id: 745f20de-2bca-11e4-bd5d-002590f28d7e If the new install doesn't work or if there are some "issues", can I simply restore the Apache2 directory from backup and then I'll just be back where I started? I thought about just renaming the current install to something like c:\apache2_old and if something fails, I can delete the new install and rename c:\apace2_old back to c:\apache. What do you all think?

  Read the article

• Does Chrome use a different DNS server while Firefox and IE use a different one?

  - by Jian Lin

  Is the common set up for Chrome that it will use a different DNS server, while Firefox and IE will use a different one? My Chrome (including the one on the virtual PC) will sometimes "Resolving host" and wait there for 20, 30 seconds, while Firefox and IE won't. (so after 20, 30 seconds with a blank page, the page will finally not be able to load). So is there something that Chrome is doing that make the difference?

  Read the article

• Dropbox doesn't recognize camera (for Camera Upload)

  - by Lee

  I'm running OS X 10.6.8 on a MacBook Pro 13" 2011 version, trying to use Dropbox 1.4.7 Camera Upload. When I connect my Sony HDR-XR260 video camera or my Blackberry Torch 9800 via USB or even an SD card via the built-in reader, Dropbox never recognizes any of it and the pop-up dialog box never pops up to ask me if I want to import my videos or not. I do have the option enabled in DB preferences. Any solutions?

  Read the article

• How do I mount a sparse disk image permanently?

  - by Mike

  On Mac OS X 10.6.7, when I mount a sparse disk image (either by double-clicking it or using hdid from the command line), the image: Appears on my desktop Needs to be re-mounted every time I log in I'd like to set up the equivalent of an /etc/fstab which will mount the image when the system boots, and make it permanent - so I don't have to worry if my symbolic links will resolve or not. Is this more trouble than it's worth on a Mac? I noticed that there is no /etc/fstab, and /etc/fstab.hd contains a dire warning: IGNORE THIS FILE. This file does nothing, contains no useful data, and might go away in future releases. Do not depend on this file or its contents. I tried sudo hdid -notremovable <image>, which seemed like half of what I wanted (according to man hdid), but it failed with an error: hdid: attach failed - no mountable file systems.

  Read the article

• Will Windows 7 setup overwrite Windows 8 and Ubuntu boot records?

  - by Jens

  I have Windows 8 and Ubuntu installed, both an the same physical hd (2 partitions). Windows 8 was installed after a format, Ubuntu afterwards. I used EasyBCD to setup the boot records and the boot menu order. I want to install Windows 7 as a third operating system and just add its boot record with EasyBCD. Will there be any unwanted behavior when I install it on a third partition? I already have 100 GB of unallocated space on the disk, though have not yet made the partition. I red on this site that I should install the oldest OS first, but than I would have to do a format and start again from scratch (which I clearly do not want to do). edit: On this site, the opposite is claimed, saying it's also possible to install Windows 7 after Windows 8. However, it will restore a Windows 7 boot menu instead one of Windows 8.

  Read the article

• OS X: How to force traffic through a specific SOCKS proxy on a per-app basis?

  - by GJ.

  I'm running a certain desktop app (actually via AIR if it makes any difference) which doesn't have any built-in proxy configuration settings. I need to get all traffic just from this app directed through a secure SOCKS proxy. This implies I can't use the global network preferences, as these would affect many other apps. Is there any way to force all network communication through a given SOCKS proxy on a per-app basis?

  Read the article

• Windows Server 2008 is stuck at "configuring updates - stage 3 of 3 - 0% complete"

  - by Chris

  This has happened the last two times I've done updates to this system, and I really have no idea what is going on. It is installing a only a month's worth of updates. It only responds to ping and no services are up, so I can't view the system remotely (I have to hook up a monitor to see this message). In the past I've just restarted the system at this point and it eventually finishes updating. I want to know what I can do to avoid this situation, how to diagnose what is going on, and how to get any kind of remote access during the updates. Edit: I can start the machine in safe mode (where I did nothing but backup some files). I restarted and it no longer tries to do a windows update, just goes to the desktop where everything seems extremely broken. I can click on some things, but not launch most programs. I guess all I can do at this point is do a system restore or something.

  Read the article

• Windows Software to Save Arbitrary Application State

  - by ashes999

  VM software does a great job of saving state when you "turn it off," allowing instant and immediate return to that previous state. Is there some application for Windows that allows me to do the same thing, for any arbitrary software? It would allow me to save/restore state, possibly via a shell command or button that it appends to every window. Edit: For clarity, there are two types of apps: those that save their own states, and those that save others' states. Those that save their own state are like Chrome, which on load, reloads the windows you had open last time. That's not what I'm asking about; I'm asking for an app that can save the state of other apps, kind of like VM software does; but for any app. (A trivial test would be load notepad++, type a bunch of stuff, and save-state; on reset-state, you should be able to multi-level undo a lot of what you wrote, as if you never shut down the application.)

  Read the article

• Windows XP Home Adobe.Com folder trying to install twice

  - by John Martinez

  Twice I had to reinstall because Adobe 9 installed for a second time without me requesting or being asked to. There is a Adobe folder and an Adobe(2) folder. Installed were Adobe.com; AIS; Reader 9 and Active X. The system crashes. I can't do anything. In safe mode, can't uninstall or system restore. Can't click on anything in regular environment. Not only will I start looking for alternative pdf reader, and if I can't view a site without active X so be it. But if I do decide to re-install Adobe, HOW DO I CONFIGURE IT TO NOT UPDATE AUTOMATICALLY???? Day and a half to re-install everything.

  Read the article

• Postgresql Internals - Documentation

  - by NogginTheNog

  I'm looking for some up-to-date information about postgresql internals, specifically the query optimizer. I've found this link (referred to in the "Further Reading" section of the 8.4 docs):- http://db.cs.berkeley.edu//papers/UCB-MS-zfong.pdf but it seems quite old. That in itself is not a problem, but I wanted to be sure that I have information that is relevant. Is this the best resource for understanding how postgresql processes queries (using plans, statistics etc.) or are there others?

  Read the article

< Previous Page | 511 512 513 514 515 516 517 518 519 520 521 522  | Next Page >