Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 517/772 | < Previous Page | 513 514 515 516 517 518 519 520 521 522 523 524  | Next Page >

  • Format & Fresh Install Mac OS X Snow Leopard on Mac mini.

    - by sagar
    Hello Every one. I have purchased a DVD of Snow Leopard (Mac OS X 10.6.2) I purchased a Mac mini with Leopard (Mac OS X 10.5.7) I tried to install Mac OS X 10.6.2 Everything went perfectly. System was installed successfully. But the problem that I faced is as follows. System was installed but my older data remained as it is. (means installation didn't format every thing - means installation was done on upgrade basis.) Now, my system works with very low speed. Previous performance of Mac mini was double as compare to current upgrade version. Now - my question are as follows. Does an upgrade installation causes the performance issues in Mac OS X? Or is Snow Leopard too demanding for the Mac mini? ( 2 Ghz Intel Core 2 Duo, 1GB RAM - is this configuration OK for Snow Leopard? ) Does a fresh install work better than an upgrade?

    Read the article

  • Concerns about Apache per-Vhost logging setup

    - by etienne
    I'm both senior developer and sysadmin in my company, so i'm trying to deal with the needs of both activities. I've set up our apache box, wich deals with 30-50 domains atm (and hopefully will grow larger) and hosts both production and development sites, with this directory structure: domains/ domains/domain.ext/ #FTPS chroot for user domain.ext domains/domain.ext/public #the DocumentRoot of http://domain.ext domains/domain.ext/logs domains/domain.ext/subdomains/sub.domain.ext domains/domain.ext/subdomains/sub.domain.ext/public #DocumentRoot of http://sub.domain.ext Each domain.ext Vhost runs with his dedicated user and group via mpm-itk, umask being 027, and the logs are stored via a piped sudo command, like this: ErrorLog "| /usr/bin/sudo -u nobody -g domain.ext tee -a domains/domain.ext/logs/sub.domain.ext_error.log" CustomLog "| /usr/bin/sudo -u nobody -g domain.ext tee -a domains/domain.ext/logs/sub.domain.ext_access.log" combined Now, i've read a lot about not letting the logs out of a very restricted directory, but the developers often need to give a quick look to a particular subdomain error log, and i don't really want to give them admin rights to look into /var/logs. Having them available into the ftp account is REALLY handy during development stages. Do you think this setup is viable and safe enough? To me it is apparently looking good, but i'm concerned about 3 security issues: -is the sudo pipe enough to deal with symlink exploits? Any catches i'm missing? -log dos: logs are in the same partition of all domains. got hundreds of gigs, but still, if one get disk-space dos'd, everything will break. Any workaround? Will a short timed logrotate suffice? -file descriptors limits: AFAIK the default limit for Apache on Ubuntu Server is currently 8192, which should be plenty enough to handle 2 log files per subdomain. Is it? Am i missing something? I hope to read some thoughts on the matter!

    Read the article

  • How to configure mod_proxy_balancer to gracefully fail under high load

    - by bramp
    We have a system which has one Apache instance in front of multiple tomcats. These tomcats then connect to various databases. We balance the load to the tomcat with mod_proxy_balancer. Currently we are receiving 100 requests a second, the load on the Apache server is quite low, but due to database heavy operations on the tomcats, the load there is roughly 25% (of what I estimate they can handle). In a few weeks there is an event happening and we estimate that our requests will jump significant, maybe by a factor of 10. I'm doing everything I can do reduce the load on our tomcats, but I know we are going to run out of capacity, so I would like to fail gracefully. By this I mean, instead of trying to deal with too many connections which all timeout, I would like Apache to somehow monitor average response time, and as soon as the response time to Tomcat is getting above some threshold, I would like a error page displayed. This means that users who are lucky still get a page rendered quickly, and those who are unlucky get a error page quickly. Instead of everyone waiting far too long for their page, and eventually everyone timing out, and the database being swamped with queries which are never used. Hopefully this makes sense, so I was looking for suggestions on how I could achieve this. thanks

    Read the article

  • Windows 7 x64 wired connection problem. IP, gateway, dns assigned, can't ping. Network detected as "Network"

    - by Emil Lerch
    I am having a problem connecting to a specific wired network with my Latitude E6410 laptop. Other wired networks seem to work fine, but this one does not. I have a coworker with me with the same Intel 82577LM Gigabit Network card, and he can connect just fine. I've updated to the latest Intel drivers (11.8.75.0) and am not using Pro Set. I obtain all DHCP information just fine (IP, netmask, DNS server, default gateway). I cannot ping anything (internal or on the Internet - I tried pinging Google's public DNS servers by IP 8.8.8.8), nor can I get answers to any DNS queries through NS Lookup. Windows troubleshooting says everything is fine, but I can't get DNS responses. I've seen issues like this in the past that were related to link speed/duplex autonegotiaion failures, so I've tried manually setting link speed/duplex to all values one by one with no success. My coworker is using all default settings, so he is just using autonegotiate. Any ideas of other things to try?

    Read the article

  • After update to Windows 8.1 brigthness isn't working (changing)

    - by Bibo
    I just update my Windows 8 to Windows 8.1 by Windows Store and I have some problems. My notebook is Acer Aspire Timelinex 3820TG and I know it's little old for Windows 8 but I install them and works fine (I updated my HDD to SSD). Now I just updated Windows and I have problem with changing brightness on my dedicated graphic card (Ati HD 5650). First I can changing brigthness with fn + keys but It just changing level in OS. No change in real. I tried reinstall drivers, install drivers for my card from Acer with compatibility to Windows 7 and without change. When I switch to integrated card changing brightness works. I think the problem is with drivers but I don't know how to get it working. Thanks for help Bonus question: I have another problem (but this one is not so important). Does anyone knows what msietxghh.exe is doing? Everytime when my system runs (after update) I get message that this program stops working but I just cancel and looks everything works fine.

    Read the article

  • What are "Excess Fragments" in defragmenting a hard drive?

    - by Andrew Swift
    I'm defragmenting my hard drive (XP SP3) with PerfectDisk 7.0, and it finds 816,659 excess fragments when I ask for an analysis. [update] Specifically, it shows that the 1TB disk is 14% fragmented with 19693 fragments and 816,659 excess fragments. About 20% of the disk is still free space. What does excess fragments refer to? What is the difference between fragments and excess fragments? I have had problems in the past where I defragmented a fragmented disk and many files were corrupted. It seemed as though "excess fragments" referred to orphan pieces, where the program couldn't find out where to put them. If that was true, then defragmenting a disk resulted in many incomplete files, and in fact I defragmented a disk full of MP3's and got a lot of corrupted files as a result. Instead, I started to simply format a separate disk and copy everything from one to the other. That way there were no orphan bits, and no file corruption. Does anybody know what "excess fragments" really are?

    Read the article

  • Web based file search in the lan?

    - by Magnetic_dud
    I would like to search files in my lan easily. (over 500k files on SMB shares, it would take ages with other ways) I mean, i just need to do a quick search on file names, i don't care content indexing at all, as most of my files are in a proprietary format, and the file name is explicative enough. But, date range filters are a must for me. I just need a quick search like voidtools' everything can do, but in a network way The files are on a WHS box (lol, Videos and Music share names are not appropriate for a company, but a license for that win2003-based os is cheaper than an xp home one!) I tried: Lansearch pro: it is not good for me, as i need a quick index Network Search Engine: it would be perfect, but does not offer a date range filter Microsoft Search Server 2008 Express, but it is horrible! First, does NOT index filenames, and then, my Core2Duo is not powerful enough to run it smoothly. Google Desktop with a proxy on localhost to make it run on the lan, but i don't like the hacked result. The preinstalled Windows Search 4.0 but it sucks totally in choosing the relevance of data - uninstalled Docco... what's that? I am considering to try: Ibm omnifind DocFetcher (can it work as a client? did not investigated yet) Strigi (it looks like that it can work as a client, right?) Any ideas/suggestions?

    Read the article

  • Network bridge does not work on Windows 7

    - by D. Strout
    I am trying to use Windows 7 to bridge my wireless and wired connections together to get wireless on a second Windows XP computer (fresh install). The network bridge is created successfully, but when I connect the cable from the first computer with the bridged connections to the second one with just a wired connection, nothing happens. The second computer doesn't connect, and the first computer shows no sign of anything different. I tried bridging the connections of a third computer, and connecting this computer to the second computer. This worked (third computer bridged the wireless to the second computer). Thus, the problem must be with the first (Win 7) computer. However, I have no idea what the problem could be. All Internet Connection Sharing is turned off. Homegroup is disabled (it was originally enabled, I thought that might be a problem, so I disabled it). Also, I had VMWare fusion installed, and that created extra items in the "This connection uses the following items" box in the properties dialog. Thinking this might be causing issues, I uninstalled that too. Still, with everything I tried, I can't get it to work. Any suggestions? Edit: Another thing I noticed that might be worth mentioning: The network icon in the Win7 taskbar has a red X on it that means it's not connected, but when I click the icon, it says connected next to my wireless connection, and I am able to access the internet.

    Read the article

  • BackupPC - why does it use rsync --sender --server ... ?

    - by Jakobud
    I'm in the process of experimenting with BackupPC on a CentOS 5.5 server. I have everything pretty much setup with default values. I tried setting up a basic backup for a host's /www directory. The backup fails with the following errors: full backup started for directory /www Running: /usr/bin/ssh -q -x -l root target /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Xfer PIDs are now 30395 Read EOF: Connection reset by peer Tried again: got 0 bytes Done: 0 files, 0 bytes Got fatal error during xfer (Unable to read 4 bytes) Backup aborted (Unable to read 4 bytes) Not saving this as a partial backup since it has fewer files than the prior one (got 0 and 0 files versus 0) First of all, yes I have my ssh keys setup to allow me to ssh to the target server without requiring a password. In the process of troubleshooting, I tried the above ssh command directly from the command line, and it hangs. Looking at the end of the debug messages for SSH I get: debug1: Sending subsystem: /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Request for subsystem '/usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/' failed on channel 0 Next I started looking at the rsync flags. I did not recognize --server and --sender. Looking at the rsync man pages, sure enough, I don't see anything about --server or --sender in there. What are those in there for? Looking at the BackupPC config I have this: RsyncClientPath = /usr/bin/rsync RsyncClientCmd = $sshPath -q -x -l root $host $rsyncPath $argList+ And for the arguments, I have the following listed: --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive Notice there is no --server, --sender or --ignore-times. Why are these things getting added in? Is this part of the problem?

    Read the article

  • Issues installing apache debian

    - by Belgin Fish
    I'm having issues installing apache2, and pretty much everything in general, I'm using debian. I run sudo apt-get install apache2 and then it returns root@debian:~# apt-get install apache2 Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: apache2 : Depends: apache2-mpm-worker (= 2.2.16-6+squeeze7) but it is not going to be installed or apache2-mpm-prefork (= 2.2.16-6+squeeze7) but it is not going to be installed or apache2-mpm-event (= 2.2.16-6+squeeze7) but it is not going to be installed or apache2-mpm-itk (= 2.2.16-6+squeeze7) but it is not going to be installed Depends: apache2.2-common (= 2.2.16-6+squeeze7) but it is not going to be installed E: Broken packages Not really sure what's up :S Seems like it can't find any of the required packages for anything, Anyone know what I'm doing wrong?

    Read the article

  • Messed up USB stick doesn't show in blkid

    - by Felix
    I was playing around with a USB stick (booting archlinux with qemu off of it and trying to perform an installation on the same stick at the same time -- brave, I know, but I was just messing around). Now, after failing to boot and install at the same time, it seems I have sort of messed up my stick. What I think happened is that I used cfdisk to wipe everything on it and create one big partition, but formatting it then failed, so now there's a big partition with no filesystem. Just to make it clear: I'm not worried for my stick, I know I can recover it at any point. What I find intriguing is that after plugging the stick into my computer (using Ubuntu), there's no (terminal) way to find out what block device (/dev/sdx) it has associated. The only way I could determine that was with GParted: But blkid shows the following: /dev/sda1: UUID="12F695CFF695B387" LABEL="System Reserved" TYPE="ntfs" /dev/sda2: UUID="A0BAA6EABAA6BC62" TYPE="ntfs" /dev/sdb1: UUID="546aec8b-9ad6-4571-b07a-adba63e25820" TYPE="ext4" /dev/sdb2: UUID="2a8b82d8-6c6e-4053-a446-bab970d93d7c" TYPE="swap" /dev/sdb3: UUID="7cbede7d-c930-4e59-9d1b-01f2d79bd092" TYPE="ext4" No trace of /dev/sdc. My question is: if I didn't have a graphical interface (to use GParted), how would I have known which block device is my stick?

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • only port working with mod_proxy is 8009, trying to use with tomcat and httpd, dont know why

    - by techsjs2012
    I am trying to use mod_proxy with httpd and tomcat. If I leave tomcat ajp to run on 8009 in the server.xml of tomcat and in the httpd.conf of apache httpd everything works great but once I change it to anything else and restart them both it does not work.. I trieded 8109,8209 and 8019.. only thing that works is 8009? Below is my setup that works. <Proxy balancer://testcluster stickysession=JSESSIONID> BalancerMember ajp://127.0.0.1:8009 min=10 max=100 route=node2 loadfactor=1 </Proxy> ProxyPass /examples balancer://testcluster/examples <Location /balancer-manager> SetHandler balancer-manager AuthType Basic AuthName "Balancer Manager" AuthUserFile "/etc/httpd/conf/.htpasswd" Require valid-user </Location> if I change the port to anything in here and the server.xml of tomcat it does not work but I can telnet the port so I know its up? below are the other libs settings I have LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule include_module modules/mod_include.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule status_module modules/mod_status.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule info_module modules/mod_info.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule userdir_module modules/mod_userdir.so LoadModule alias_module modules/mod_alias.so LoadModule substitute_module modules/mod_substitute.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_balancer_module modules/mod_proxy_balancer.so LoadModule proxy_ajp_module modules/mod_proxy_ajp.so #LoadModule proxy_ftp_module modules/mod_proxy_ftp.so #LoadModule proxy_http_module modules/mod_proxy_http.so #LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so

    Read the article

  • Apache is spawning more and more processes!!

    - by erotsppa
    We have a LAMP setup that is working prety good for half a year. All of a sudden today the apache server (mysql servers are not on this box) started to die. It seems to have started to spawn more and more processes over time. Eventually it will consume all the memory and the server would just die. We are using prefork. In the mean time what we are doing is just added more ram and increased the MaxClients and ServerLimit parameter to 512. We're just prolonging the crash. The number still goes up slowly. Maybe in a day, it would reach that limit. What is going on? We only have around 15-20 request per second. We have 1Gb memory and it's not half used, there's no swapping going on. Why is apache creating more and more processes? It's almost like theres a leak somewhere! The database boxes are fine, they are not causing a delay to requests. We tested some queries everything is quick!

    Read the article

  • OpenVPN, install a TAP adapter

    - by GolezTrol
    When I try to connect to my work VPN using OpenVPN, the connection fails with the message: All TAP-Win32 adapters on this system are currently in use. Many sources suggest to look in Control Panel\Network and Internet\Network Connections an enable the TAP adapter, but when I look there, there is none. Now I've run addtap.bat which is provided with OpenVPN, but I still don't get to see any TAP adapter, and logging in in VPN still fails. The output of addtap.bat is C:\Windows\system32>"C:\Program Files (x86)\OpenVPN\bin\tapinstall.exe" install "C:\Program Files (x86)\OpenVPN\driver\OemWin2k.inf" tap0801 Device node created. Install is complete when drivers are updated... Updating drivers for tap0801 from C:\Program Files (x86)\OpenVPN\driver\OemWin2k .inf. Drivers updated successfully. I've Run As Administrator both the setup of OpenVPN and addtap.bat. I've run deltapall.bat to remove any (maybe hidden) adapters. It said it removed three of them, after which I ran addtap.bat again to try to create another one. I also run OpenVPN itself as administrator. What's wrong? Running Windows 7 Home Premium on a HP Pavilion dv7 4050ed. It has worked before, but I recently had to reinstall my laptop, for which I used the restore disks I created when I just got it. Everything else seems to work fine. == UPDATE == The TAP adapter is found in Device Manager, but apparently it is disabled because it is incompatible with Windows 7 64bit. I've deïnstalled OpenVPNGui, downloaded a version that should be 64bit compatible, and installed that. Still no cigar. Then I found a tip to install OpenVPN (version 9) after installing OpenVPNGui, because that installs OpenVPN version 8. Now I got a v9 TAP driver in Device Manager, but it still doesn't work and shows up in device manager with an exclamation mark, and not at all in my network devices.

    Read the article

  • Windows server 2008R2 routing with single NIC

    - by Fabian
    I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

    Read the article

  • Need to Remove Exchange 2003 Server That Crashed During Transition to 2010

    - by ThaKidd
    As the title stated, we were running an Exchange 2003 server that we knew was going down soon so we purchased a second server and installed Exchange 2010 into the AD. We managed to move all of the mailboxes off of 2003 and also managed to get the Offline Address Book setup on 2010. At this point the 2003 server bit the dust and will no longer boot. Therefore we were unable to properly uninstall Exchange and remove the last 2003 server so it still exists in AD. As far as the clients are concerned, everything is working properly. However, when I run the Microsoft Exchange Profile Analyzer, I still see the old server and its Administrative Group. I am going to guess that since the old server is showing up in AD, I will not be able to raise Exchange or AD functionality (as the 2003 server was also the only AD DC) levels. I have forced the 2003 DC out of AD so that is no longer an issue. Old Setup: Windows 2003 Server Enterprise & Exchange 2003 Standard New Setup: Windows 2010 Server Enterprise & Exchange 2010 Standard Two Questions: How do you go about manually forcing the 2003 server and its administrative group out of AD? When that is finished, where do you raise the Exchange mode (can't find this for the life of me)?

    Read the article

  • Unix Permissions: Enable access to files no matter the user?

    - by TK Kocheran
    I've been using Linux for a long time and I still am completely in the dark about how file permissions really work. With that in mind, does anyone have any books or thorough guides I could read to really understand things completely? I've done my fair share of sysadminning, so I know the easy stuff like making directories readable and writable, making files executable, and changing the owner of a file, but on sharing files across users, I'm lost. Here's my main problem. I have a number of machines across which I intend to synchronize my music library. I've been using Unison for a while now and it's a great choice as I can easily run it over SSH on my local network which I just set up. Win-win. Up until this point, I've been synchronizing computers using a 2TB external hard drive. (computer 1 unisons to HD, computer 2 unisons to HD, etc.) This is tedious at best, especially since I encrypted the drive, making it a huge hassle to hook it up to all of my machines and sync it. Anyway, the drive is running ext4 (in TrueCrypt), so it maintains all Unix filesystem info like owners and groups. I just set up a new machine and just Unison'd it to get the music on it, and I realized that now, all of my permissions are fubar. I had to run Unison as root since that was the only way I could get the files to come off of the external drive. Apparently, since I'm using a different user name on this machine than my usual "rfkrocktk" across all machines, this essentially throws a huge wrench in the gears. Here's my use case. This laptop has two effective users, "leandra" and "rfkrocktk". I want to share music between these two users, so I symlinked /home/rfkrocktk/Music to point to /home/leandra/Music. How do I (a) allow both users access to read/write/delete files in this folder, and (b) keep everything nicely in sync without messing up file ownership?

    Read the article

  • Strange windows boot problem - My computer won't boot from hard disk

    - by user29779
    Hello, Until yesterday, I had windows XP installed on my computer. After installing the OS, and setting the BIOS to boot from the hard-disk first, I discovered a strange problem - the OS wasn't booted and the only way I could get it to load was to insert a windows installation disk, enter repair mode, do "fixboot" and restart. The problem only occured when the computer was booted after shut-down. If I only restarted it, everything worked fine. Yesterday, I upgraded my XP to win7 and the problem persists. I tried the same "trick" I did with XP to get it to load, by entering repair and doing "bootrec /fixmbr" and "bootrec /fixboot" but that didn't work (and when I run "scanos" it didn't find any windows installations). Eventually, I got it to load by changing the settings in the BIOS to boot from CD first and HD second, removing the installation disk from the drive, letting it fail to boot from CD and then re-insert the disk. Anyone has any idea what may be the cause or how can I investigate this issue? Thanks! Marina

    Read the article

  • Rebuild Apple RAID set

    - by Clinton Blackmore
    We have a Mac Pro tower with an Apple RAID card in it using third party drives. When one drive failed, we replaced it and the RAID 5 set was nearly done rebuilding when the computer was rebooted. It did not come back up. We are now booting up off of a different internal volume, and have three (third-party) drives of identical spec (including revision and firmware) in the box. One of the drives is a global spare; the other two are recognized as belong to a RAID set but are in "Roaming" mode. The intention is to recreate the three-drive RAID set using the data on the two drives that are good. When we tell the system to create a RAID 5 using the three drives, it tells us that it'll create a RAID set but everything will be lost. There are no obvious options to rebuild a RAID using the two good drives and incorporating the third drive in Apple's RAID Utility, and we've looked through the options for the raidutil command. Fortunately, all important data is backed up, and we can rebuild from scratch, but, is there any way to make the RAIDset work again?

    Read the article

  • How to use different scaling for every monitor?

    - by Mikael Koskinen
    One of the new features in Windows 8.1 is the new "Desktop display scaling", which allows user to configure scaling per monitor. I've been trying to get this working in preview but with no success. If I configure the scaling, it always affects all of my monitors. I have two monitors, the main one with a higher resolution and the secondary with "normal" resolution. The secondary monitor is used in portrait mode. I would like to configure the main monitor's scaling as the text is currently too small. Here's how things look at the configuration screen by default: Now if I adjust the scaling, click apply and do relogin, everything is bigger. On both of my monitors. I haven't clicked the "Let me choose one scaling level for all my displays", but still the slider seems to affect both of them. If I check the "Let me choose one scaling level", the UI changes to look similar to what we have in Windows 8: Still the problem persists. The scaling is applied to both of my monitors. So, it doesn't matter if I check the box or not, the scaling is always applied to all the displays. Any idea how I could get this to work in preview? I've read some comments which seem to indicate that this should work in preview, though Paul Thurrott mentioned at his Winsupersite article that he either didn't get this to work.

    Read the article

  • AWS Linux EC2: yum won't run with plugins

    - by Patrick
    Short Version: yum commands on my Amazon Linux EC2 AMI only work with --noplugins. Long Version: A couple of days ago, I ran yum update at the behest of the SSH Login MoTD telling me I had updates to install. About midway through the update (specifically while updating the kernel), the update abruptly ended (79 of 138 items completed). The website I host on EC2 got weird for a few minutes, but eventually seemed to stabilize back out (maybe EC2 restarted itself?), and I didn't have further issues (other than MySQL started running out of memory, but I think that's probably unrelated to this). Today, I went to install gcc-c++ (with yum install gcc-c++). When I did, I got the following message: Loaded plugins: priorities, security, update-motd, upgrade-helper Config error: Command "updateinfo" already defined and I get that for any command I can think to run using yum. However, If I throw in the --noplugins flag, then magically it seems to work. To be clear, when I installed a different package a week ago, it worked totally correctly, so the yum update is the only thing I can think of that changed. I could find nothing on Google with regard to "updateinfo" already defined (with and without quotes). I tried running yum update --noplugins which spit out a message telling me that I should have run yum-complete-transaction instead, but proceeded to try to update something on its own. When that completed, I tried yum-complete-transaction but that gave me a message about the transactions not lining up correctly, so it removed the old transaction (Probably since I should have completed the first transaction before trying to update again, if I had known). Based on the SF question "Linux EC2 Broken Yum", I've also tried yum clean all --noplugins (fails the same with plugins) which just gives me Cleaning repos: amzn-main amzn-updates rpmforge Cleaning up everything I also tried package-cleanup --problems Loaded plugins: priorities, update-motd, upgrade-helper No Problems Found and package-cleanup --dupes Gives a lot of dupes, so I pasted them here: http://pastebin.com/VVFQEkTT instead of inline. At this point, I'm not sure what else there even is to check.

    Read the article

  • mod_rewrite REQUEST_FILENAME doesn't contain absolute path

    - by Paul Dixon
    I have a problem with a file test operation in a mod_rewrite RewriteCond entry which is testing whether %{REQUEST_FILENAME} exists. It seems that rather than %{REQUEST_FILENAME} being an absolute path, I'm getting a path which is rooted at the DocumentRoot instead. Configuration I have this inside a <VirtualHost> block in my apache 2.2.9 configuration: RewriteEngine on RewriteLog /tmp/rewrite.log RewriteLogLevel 5 #push virtually everything through our dispatcher script RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^/([^/]*)/?([^/]*) /dispatch.php?_c=$1&_m=$2 [qsa,L] Diagnostics attempted That rule is a common enough idiom for routing requests for non-existent files or directories through a script. Trouble is, it's firing even if a file does exist. If I remove the rule, I can request normal files just fine. But with the rule in place, these requests get directed to dispatch.php Rewrite log trace Here's what I see in the rewrite.log init rewrite engine with requested uri /test.txt applying pattern '^/([^/]*)/?([^/]*)' to uri '/test.txt' RewriteCond: input='/test.txt' pattern='!-f' => matched RewriteCond: input='/test.txt' pattern='!-d' => matched rewrite '/test.txt' -> '/dispatch.php?_c=test.txt&_m=' split uri=/dispatch.php?_c=test.txt&_m= -> uri=/dispatch.php, args=_c=test.txt&_m= local path result: /dispatch.php prefixed with document_root to /path/to/my/public_html/dispatch.php go-ahead with /path/to/my/public_html/dispatch.php [OK] So, it looks to me like the REQUEST_FILENAME is being presented as a path from the document root, rather than the file system root, which is presumably why the file test operator fails. Any pointers for resolving this gratefully received...

    Read the article

  • Using git through cygwin on windows 8

    - by 9point6
    I've got a windows 8 dev preview (not sure if it's relevant, but I never had this hassle on w7) machine and I'm trying to clone a git repo from github. The problem is that my ~/.ssh/id_rsa has 440 permissions and it needs to be 400. I've tried chmodding it but the any changes on the user permissions gets reflected in the group permissions (i.e. chmod 600 results in 660, etc). This appears to be constant throughout any file in the whole filesystem. I've tried messing with the ACLs but to no avail (full control on my user and deny everyone resulted in 000) here's a few outputs to help: $ git clone [removed] Cloning into [removed]... @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: UNPROTECTED PRIVATE KEY FILE! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ Permissions 0660 for '/home/john/.ssh/id_rsa' are too open. It is required that your private key files are NOT accessible by others. This private key will be ignored. bad permissions: ignore key: /home/john/.ssh/id_rsa Permission denied (publickey). fatal: The remote end hung up unexpectedly $ ll ~/.ssh total 6 -r--r----- 1 john None 1675 Nov 30 19:15 id_rsa -rw-rw---- 1 john None 411 Nov 30 19:15 id_rsa.pub -rw-rw-r-- 1 john None 407 Nov 30 18:43 known_hosts $ chmod -v 400 ~/.ssh/id_rsa mode of `/home/john/.ssh/id_rsa' changed from 0440 (r--r-----) to 0400 (r--------) $ ll ~/.ssh total 6 -r--r----- 1 john None 1675 Nov 30 19:15 id_rsa -rw-rw---- 1 john None 411 Nov 30 19:15 id_rsa.pub -rw-rw-r-- 1 john None 407 Nov 30 18:43 known_hosts $ set | grep CYGWIN CYGWIN='sbmntsec ntsec server ntea' I realize I could use msysgit or something, but I'd prefer to be able to do everything from a single terminal Edit: Msysgit doesn't work either for the same reasons

    Read the article

  • Cacti is ignoring hash marks in interface aliases

    - by Matt Simmons
    I'm attempting to set up Cacti to monitor a router's interfaces, and I'm having trouble getting the graph templates to show the information that I'd like. Our interface configuration looks like this: interface GigabitEthernet3/6 description WalljackNumber # Server info no ip address no shutdown switchport switchport access vlan 116 switchport mode access ip dhcp snooping trust spanning-tree portfast The "Server Info" string is really just the machine name, and a short relevant description, such as "PolarSprings vmnic2". The important part appears to be that it follows the hashmark. When I run snmpwalk, I get the proper output: IF-MIB::ifAlias.230 = STRING: WalljackNumber # Server info But in Cacti, when I go into the graph templates and set the title to this: |host_description| - Traffic - |query_ifName| (|query_ifAlias|) All that shows up in the graph is: switchname - Traffic - Gi3/6 (WalljackNumber #) Which strikes me as a little weird. What I suppose MAY be happening is that somewhere in the cacti stream, it's interpreting # as being a comment and stripping everything after, but I'm not sure. I was hoping someone could tell me that this was a known documented behavior, or that I could change it in a setting that I wasn't aware of. The alternative answer is to change the delimiter from # to something else, but I've got over a thousand lit switchports on an old college infrastructure, and I'm not sure what else might be relying on them.

    Read the article

< Previous Page | 513 514 515 516 517 518 519 520 521 522 523 524  | Next Page >