Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 519/772 | < Previous Page | 515 516 517 518 519 520 521 522 523 524 525 526  | Next Page >

  • Cisco QoS Guidance

    - by Kyle Brandt
    I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future. I do have VOIP at one location connected to this one over the Internet that goes through a VPN tunnel. Everything else that is between this location and other offices is on a separate MPLS network.

    Read the article

  • mod_cache not working

    - by Pistos
    I have a PHP site that has many dynamically generated pages. I'm trying to turn to mod_cache to help boost performance, because in most cases, content does not change in a given day. I have configured mod_cache as best I could, following examples around the web, including the mod_cache page on apache.org. When I set LogLevel debug, I see a bit of information about the caching that is [not] happening. There are plenty of pairs of lines like this: [Fri Jun 01 17:28:18 2012] [debug] mod_cache.c(141): Adding CACHE_SAVE filter for /foo/bar [Fri Jun 01 17:28:18 2012] [debug] mod_cache.c(148): Adding CACHE_REMOVE_URL filter for /foo/bar Which is fine, because I've set CacheEnable disk /foo, to indicate that I want everything under /foo cached. I'm new to mod_cache, but my understanding about these lines is that it just means that mod_cache has acknowledged that the URL is supposed to be cached, but there are supposed to be more lines indicating that it is saving the data to cache, and then later retrieving them on subsequent hits to the same URL. I can hit the same URL till I'm blue in the face, whether with F5 refreshing, or not, or with different browsers, or different computers. It's always that pair of lines that shows in the logs, and nothing else. When I set CacheEnable disk /, then I see more activity. But I don't want to cache the entire site, and there are many, many different subpaths to the site, so I don't want to have to modify code to set no-cache headers in all the necessary places. I'll mention that mod_rewrite is in use here, rewriting /foo/bar to something like index.php?baz=/foo/bar, but my understanding is that mod_cache uses the pre-rewrite URL, not the post-rewrite URL. As far as I can tell, I have the response headers not getting in the way of caching. Here's an example from one hit: Cache-Control:must-revalidate, max-age=3600 Connection:Keep-Alive Content-Encoding:gzip Content-Length:16790 Content-Type:text/html Date:Fri, 01 Jun 2012 21:43:09 GMT Expires:Fri, 1 Jun 2012 18:43:09 -0400 Keep-Alive:timeout=15, max=100 Pragma: Server:Apache Vary:Accept-Encoding mod_cache config is as follows: CacheRoot /var/cache/apache2/ CacheDirLevels 3 CacheDirLength 2 CacheEnable disk /foo What is getting in the way of mod_cache doing its job of caching?

    Read the article

  • How to sync two computers using new MobileMe calendar

    - by CesarGon
    I have been using MobileMe for over a year with success. I use it to sync my Outlook calendars in my work and home computers, using Windows 7 and Outlook 2007. The main Outlook calendar folder in my work computer is replicated to MobileMe as "Work", and synced to my home computer, and the main calendar folder in my home computer is replicated to MobileMe as "Home", and synced to my work computer. This means that I can see both "Work" and "Home" calendars from both computers (as well as from the web interface through me.com), which is very convenient. Yesterday I migrated to the new MobileMe calendar, accepting the suggestion that popped up on the me.com website. After the migration, the MobileMe control panel on each of Windows computers asked me to re-configure my calendar setup, and everything fell apart. The "Home" and "Work" calendar folders in Outlook are now ignored by MobileMe, and new ones named "Home in MobileMe" and "Work in MobileMe" have been created, and placed in a separate Outlook data file rather than the default. This means that now: I now have four folders, two of which are not replicated to MobileMe The two folders that are not replicated reside on a separate data file, so alarms and reminders don't work; they're basically useless to me as calendar folders In addition, the button in the MobileMe Control Panel that used to let me specify what MobileMe folder should be synced against the default Outlook folder has gone. MobileMe is now too smart. Do you have any idea how to undo this mess and go back to a situation where I have two folders, as described in the top paragraph, which keep synced? I don't want an extra data file. Thanks.

    Read the article

  • How do I keep my Mac from constantly going to sleep?

    - by David
    The system is a PowerPC Mac Mini running MacOS Tiger 10.4.11. When I login (I'm the admin), everything seems fine - until about 10-15 minutes later. Then the system goes into sleep mode. Each time I try to wake the system up - I can barely log in before it goes to sleep again. Sometimes I don't have enough time to enter my password (from the screen saver). If I shut down and restart, then I have that 10-15 mins again - until it again goes to sleep. I checked the settings in the Displays and Energy System Prefs. I looked at Accounts and at Screen Saver System Prefs; no times seemed to be present. I've already reset the PROM and other things (as part of an earlier problem shooting session). If I don't log in at the desktop, things seem to be fine. Nothing in .profile, /etc/profile, or /etc/bashrc seems to stand out. Right now, the system is hardly usable; can someone help? Many thanks...

    Read the article

  • How do I keep my Mac from constantly going to sleep?

    - by David
    The system is a PowerPC Mac Mini running MacOS Tiger 10.4.11. When I login (I'm the admin), everything seems fine - until about 10-15 minutes later. Then the system goes into sleep mode. Each time I try to wake the system up - I can barely log in before it goes to sleep again. Sometimes I don't have enough time to enter my password (from the screen saver). If I shut down and restart, then I have that 10-15 mins again - until it again goes to sleep. I checked the settings in the Displays and Energy System Prefs. I looked at Accounts and at Screen Saver System Prefs; no times seemed to be present. I've already reset the PROM and other things (as part of an earlier problem shooting session). If I don't log in at the desktop, things seem to be fine. Nothing in .profile, /etc/profile, or /etc/bashrc seems to stand out. Right now, the system is hardly usable; can someone help? Many thanks...

    Read the article

  • How to forceably unmount stuck network share in Mac OS X?

    - by Kyle Lowry
    Not long ago my Xserve failed (power loss) while an iMac was working with files on a particular network share (called "Work Share"). This volume, "Work Share", is now stuck. It can't be seen in the GUI, you can only detect it using the Terminal. Even after power cycling over the course of several days, ls -a still shows that it's there, but I can't unmount it using any command - not even as root in single user mode. Every time I attempt to unmount that volume, I get the message that the resource is busy (which it can't possibly be since nothing is using it), and error code 4915. The issue is that when I mount the real "Work Share", it internally is renamed to "Work Share-1", which breaks all my links, and several files in the share. If I can't unmount the false "Work Share", then that computer would be unuseable without a reformat, I would imagine - and I don't want it to have to come to that. I've tried everything I can think of - it looks like sudo can't save me now. Any ideas on how to unmount this stuck volume?

    Read the article

  • what is the fastest way to copy all data to a new larger hard drive?

    - by SUPER user
    I was certain this would have been covered before, but I cannot find an answer amongst all the almost-duplicates that come up; sorry if I've missed something obvious. I have a full 320gb disk inside my machine, a new 1tb disk to replace it, and a USB 2.0 chassis. It is only data on a single partition, no OS/apps involved, and the old drive will be kept somewhere as backup (no secure wiping etc). The simple option would be to put new disk in USB chassis, copy files, then swap them over. But for USB pen drives, reading is around 4x faster than writing. If the same is true for a USB SATA chassis (is it?) then it would be significantly faster to swap the drives first and read from the old drive over USB, right? Then the other consideration is that copying lots of files is usually slower than a single file of equivalent size. Is Windows 7 smart enough to do everything in a single lump like that, or is there specialised software that should be used instead? (Even if SATA-SATA copying is faster than involving USB, knowing what to do when it isn't an option is useful information.) Summary: Does a USB SATA chassis suffer from a read/write inequality? (like a USB pen drive does, but unlike a direct SATA connection) Can Windows 7 do sequential access? (I can't find confirmation if Robocopy does this.) Or is it necessary to use a bootable CD/USB with something like Clonezilla to achieve sequential copy speeds?

    Read the article

  • Adding new SPNs to existing service ids

    - by jmh
    We have a tomcat server using spring-security kerberos to authenticate users to the webpage against active directory. There are around 25 domain controllers. The site has two CNAME based DNS aliases. The site currently has one Service ID with SPNs registered for the DNS A record as well as each of the CNAMEs. While everything is working right now, I don't know how to reliably change this configuration without possible downtime. The reason is that clients cache kerberos tickets: http://www.juniper.net/techpubs/en_US/uac4.2/topics/concept/user-role-active-directory-about.html The 'kerbtray.exe' program is helpful for viewing and deleting Kerberos tickets on the endpoint. Old tickets must be purged from the endpoint if SPNs are updated or passwords are changed (assuming the endpoint still has a cached copy of the ticket from a prior SPNEGO request to the MAG Series device. During testing, you should purge tickets before each authentication request. Description of "klist" program used to inspect/delete cached tickets: http://technet.microsoft.com/en-us/library/hh134826.aspx So if each of the clients (users running windows) who connect to my web server have kerberos tickets that become invalid as soon as I update the SPNs or passwords, how do I ensure changes are seamless? Are there any operations that can be done safely? I can't just ask all of the users to install klist and delete their old tickets.

    Read the article

  • Can't login to phpMyAdmin on a WAMP server running Windows 2008

    - by Richard West
    I am setting up a new server. I have installed Apache 2.2.17, PHP 5.3.3, MySQL 5.1.53 and phpMyAdmin 3.3.8 running on a Windows 2008 (32 bit) OS. I have configured Apache and PHP so they appear to be working fine. I have created the standard test php page with the following code and everything appears to be working fine. <?php //index.php phpinfo(); ?> I also see the mySQL and mySQLi section in the above webpage, so it appears that that I have the proper extensions loaded for mySQL access. The problem that I am having centeres around myPHPAdmin. I have this installed and I can access to the login screen at http://localhost/pma I login using "root" and the password I have setup for root. After a delay of 30 seconds or so the web page goes to a blank screen, and the url is now http://localhost/pma/index.php?token= No error is ever displayed - however nothing usable is either. I have confirmed that mySQL is running by going to the command line and logging into mySQL from there. I have double checked my configuration but I am not having any luck getting this to work. I have also disabled the Windows firewall, but that did not change anything. I installed mySQL using the standard port 3306. Any advice would be greatly appreciated.

    Read the article

  • How do I make rsync also check ctime?

    - by Benoît
    rsync detects files modification by comparing size and mtime. However, if for any reason, the mtime is unchanged, rsync won't detect the change, although it's possible to spot it by looking at the ctime. Of course, I can tell rsync do compare the whole files' contents, but that's very very expensive. Is there a way to make rsync smarter, for example by checking mtime+size are the same AND that ctime isn't newer than mtime (on both source and destination) ? Or should I open a feature request ? Here's an example: Create 2 files, same content and atime/mtime benoit@debian:~$ mkdir d1 && cd d1 benoit@debian:~/d1$ echo Hello > a benoit@debian:~/d1$ cp -a a b Rsync them to another (non-exisiting) directory: benoit@debian:~/d1$ cd .. benoit@debian:~$ rsync -av d1/ d2 sending incremental file list created directory d2 ./ a b sent 164 bytes received 53 bytes 434.00 bytes/sec total size is 12 speedup is 0.06 OK, everything is synced benoit@debian:~$ grep . d*/* d1/a:Hello d1/b:Hello d2/a:Hello d2/b:Hello Update file 'b', same size and then reset its atime/mtime benoit@debian:~$ echo World > d1/b benoit@debian:~$ touch -r d1/a d1/b Attempt to rsync again: benoit@debian:~$ rsync -av d1/ d2 sending incremental file list sent 63 bytes received 12 bytes 150.00 bytes/sec total size is 12 speedup is 0.16 Nope, rsync missed the change. benoit@debian:~$ grep . d*/* d1/a:Hello d1/b:World d2/a:Hello d2/b:Hello Tell rsync the compare the file content benoit@debian:~$ rsync -acv d1/ d2 sending incremental file list b sent 144 bytes received 31 bytes 350.00 bytes/sec total size is 12 speedup is 0.07 Gives the correct result: benoit@debian:~$ grep . d*/* d1/a:Hello d1/b:World d2/a:Hello d2/b:World

    Read the article

  • ESX 4.0 space: DASD, NAS, or ?

    - by thormj
    I put together an ESX box for better management, but its performance is a WTF item; I'm a noob at dealing with ESX, so I'm looking for a laundry-list of reading material to help me straighten this out so I can go back to .NET programming. Current storage system: We're running Raid5+Hotspare (8x500 GB spindles) on a PERC6i on a Dell 2910. Due to ESX limitatios, the PERC is showing the storage as 1x2TB + 1x800GB "partitions." I'm not sure of the setup's configuration (stride / stripe / ???) at all. Our Applications We have a SBS server as well as a minor (2x50 GB, but growing at 10GB/month) database server... Our application that lives on the database VM is CPU and I/O insense; it's a database churning excercise mixed in with a lot of computation on the data (fixing that performance is what I'm supposed to be working on)... Perfomance Issue When I do a backup, restore, or worse (copy a backup from 1 vm to another to move it to the QA VM), the entire system slows to a crawl (even "unrelated" VMs). I originally thought a DASD situation would be quite good since you had PCI-x bandwidth, but the systemwide slowdown is killing productivity. Questions What should I do to make an intelligent decision about NAS vs RAID vs SAN vs DASD? Are there sweet spots/ugly spots in the storage setup? Can you use a SSD PCI-X card in ESX for the tempdb? Good/Bad idea? Is there any way to "share" some image in a copy-on-write fashion? Most of the "Backup-Copy-Restore" is to "put a clean image on the dev boxes"; if I could have them "share" the master image, the "big copy" (2x50 GB) would only need to be done once per week instead of once per dev per week...[runtime performance isn't a concern with the dev boxes, but the backup/copy/restore kills production, SBS, and everything else on the box]

    Read the article

  • How can I control disk numbering (enumeration) in Windows 7 Disk Management?

    - by tim11g
    A desktop system had two drives (Assigned C and D, which were enumerated in Disk Management as Disk 0 and Disk 1). A new SSD was added as the boot drive, after copying the C drive to the SSD. The SSD was connected to SATA 0 (master) port on the motherboard. The previous C Drive was moved to SATA 2 and is reformatted as a non-booting NTFS partition. The D drive remained on SATA 1. The system boots and everything seems fine. I was able to manually adjust the Drive Letters. However, the list in Disk Management is re-ordered. Disk 0 is the the previous Disk 2 (D Drive) on SATA 1, Disk 1 is the new Boot Drive (now C) on SATA 0, and Disk 2 is the former C Drive (now assigned E) on SATA 2. Does the Disk 0, 1, 2, designation mean anything? I would prefer to have them display in Disk Management as Drives C, D, and E from top to bottom. Is the Disk enumeration based on the SATA port or something else? (If it was based on SATA Port, they should be ordered C, D, E. Is there any way to re-order the Disk number assignments? What actually does determine the Disk number enumeration?

    Read the article

  • Removing forward lookup zone broke our site - why?

    - by user102469
    I'm fairly new to the job and trying to get to grips with the infrastructure here. We've moved a site from being locally hosted on our own network to an external host (1&1). I've transferred the DNS hosting from the previous DNS host to 1&1 to keep things simple. Once everything had gone through, visitors that were external to our network were being directed to the new site on 1&1 but requests from within our network were still going to our own server. I noticed in the DNS server that there was a forward lookup zone for the site pointing to our own server still. My (admittedly simplistic) understanding was that pausing that zone would then cause the DNS server to get the address for the site from our external DNS servers and our users would start landing on our new site. However, what happened instead was that they were being met with "page not found" type errors. I've resolved it my modifying the forward lookup zone A record to point to the external web server but would like to get an understanding as to why pausing the zone didn't work. Would deleting the zone work? I am reluctant to try that as creating it again will not be as easy as simply pressing "start". Many thanks.

    Read the article

  • ESXi 4.1 host not recognising existing VMFS datastore

    - by ThatGraemeGuy
    Existing setup: host1 and host2, ESX 4.0, 2 HBAs each. lun1 and lun2, 2 LUNs belonging to the same RAID set (my terminology might be sketchy here). This has been working just fine all along. I added host3, ESXi 4.1, 2 HBAs. If I view Configuration / Storage Adapters, I can see that both HBAs see both LUNs, but if I view Configuration / Storage, I only see 1 datastore. host1/2 can see both LUNs and I have VMs running on both too. I have rescanned, refreshed and even rebooted, but host3 refuses to acknowledge 1 of the datastores. Does anyone know what's going on? Update: I re-installed the host with ESX (not i) 4.0, same version as the existing hosts and it's still not recognising the vmfs. I think I'm going to SVmotion everything off that datastore then format it. Update2: I've created the LUN from scratch and the problem gets even weirder. I've presented the LUN to all 3 hosts, and I can see the LUN in the vSphere client's Configuration / Storage Adapters section on all 3 hosts. If I create a datastore on the LUN via the Configuration / Storage section on host1, it works fine and I can create an empty folder via datastore browser, but the datastore is not seen by the host2 and host3. I can use the Add Storage wizard on host2 and it will see the LUN. At this point the "VMFS Label" column has the label I gave with "(head)" appended. If I try the Add Storage wizard's "Keep the existing signature" option, it fails with an error "Cannot change the host configuration." and a dialog box that says 'Call "HostStorageSystem.ResolveMultipleUnresolvedVmfsVolumes" for object "storageSystem-17" on vCenter Server "vcenter.company.local" failed.' If I try the Add Storage wizard's "Assign a new signature" option on host2, it will complete and the VMFS label will have "snap-(hexnumber)-" prepended. At this point its also visible on host3, but not host1. I have a similar setup in a different datacenter which didn't give me all this trouble.

    Read the article

  • Postfix: Using google apps for stmp errors

    - by Zed Said
    I am using postfix and need to send the mail using google apps smtp. I am getting errors after I thought I had set everything up correctly: May 11 09:50:57 zedsaid postfix/error[22214]: 00E009693FB: to=<[email protected]>, relay=none, delay=2466, delays=2462/3.4/0/0.06, dsn=4.7.0, status=deferred (delivery temporarily suspended: SASL authentication failed; cannot authenticate to server smtp.gmail.com[74.125.155.109]: no mechanism available) May 11 09:50:57 zedsaid postfix/error[22213]: 0ACB36D1B94: to=<[email protected]>, relay=none, delay=2486, delays=2482/3.4/0/0.06, dsn=4.7.0, status=deferred (delivery temporarily suspended: SASL authentication failed; cannot authenticate to server smtp.gmail.com[74.125.155.109]: no mechanism available) May 11 09:50:57 zedsaid postfix/error[22232]: 067379693D3: to=<[email protected]>, relay=none, delay=2421, delays=2417/3.4/0/0.06, dsn=4.7.0, status=deferred (delivery temporarily suspended: SASL authentication failed; cannot authenticate to server smtp.gmail.com[74.125.155.109]: no mechanism available) main.cf: # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters #smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem #smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = zedsaid.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = #relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all delay_warning_time = 4h smtpd_recipient_limit = 16 # how many error before back off. smtpd_soft_error_limit = 3 # how many max errors before blocking it. smtpd_hard_error_limit = 12 ## Gmail Relay relayhost = [smtp.gmail.com]:587 smtp_use_tls = yes smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = noanonymous smtp_sasl_tls_security_options = noanonymous smtp_sasl_mechanism_filter = login smtp_tls_eccert_file = smtp_tls_eckey_file = smtp_use_tls = yes smtp_enforce_tls = no smtp_tls_CAfile = /etc/postfix/cacert.pem smtpd_tls_received_header = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport debug_peer_list = smtp.gmail.com debug_peer_level = 3 What am I doing wrong?

    Read the article

  • Cisco ASA with CSC module bypassing

    - by Shial
    We recently upgraded from a Watchguard X5500e Peak firewall appliance to a Cisco 5500 ASA with the CSC module. The ASA is running the 8.2 software and the CSC is on the 6.3.1172 software. We've finally gotten everything stabilized after a few weeks of pulling hairs and gnashing of teeth and now its down to trying to setup a few items that were lower on the priority list. With the watchguard we were able to go with the browser to an internal webpage and authenticate against the firewall to allow us to bypass the filters. Useful when a classroom here needs access to streaming media or an executive needs us to download a video. I'm trying to setup something similar but I'm fairly inexperienced with the Cisco devices like this ASA so I'm not sure if its treated as a VPN connection or some kind of ACL. Ideally we would want to setup more than one to limit exposure rather than one thats wide open when used. I did a search and couldn't find anything related to thing in the other questions asked here and I have had no luck googgling it either.

    Read the article

  • httpd 2.2.15 + suPHP + suExec + php5 = permission and information ?

    - by Prix
    Hi, i am currently playing around with suexec, suphp, php5 on my apache on slackware 13.1. Everything is installed and working properly but now i did like to got further into the directory permissions and at suphp settings and options available. initially i was planning to leave suphp disabled unless a virtualhost has it specified to be enabled but it does not seem to work, see sample: mod_php.conf which is included in my httpd.conf # # mod_php & mod_suPHP - PHP Hypertext Preprocessor module # # Load the PHP module: LoadModule php5_module lib/httpd/modules/libphp5.so # Load the suPHP module: LoadModule suphp_module lib/httpd/modules/mod_suphp.so <IfModule mod_php5.c> # Tell Apache to feed all *.php files through PHP. If you'd like to # parse PHP embedded in files with different extensions, comment out # these lines and see the example below. <FilesMatch \.php$> SetHandler application/x-httpd-php </FilesMatch> </IfModule> <IfModule mod_suphp.c> # This option tells mod_suphp if a PHP-script requested on this server (or # VirtualHost) should be run with the PHP-interpreter or returned to the # browser "as it is". suPHP_Engine off </IfModule> With the above first sample it makes suPHP and PHP not work if i comment out the php5 stuff but the module it will run just fine ... So my first question is, how could i possible make this setup work ? Leave suPHP disabled using php5 by default and if a virtualhost has suPHP enabled it will disable php5 and use suPHP. if any information is lacked here please let me know and i will update with any additional information you may need. Thanks in advance.

    Read the article

  • Should be simple: existing laptop with local user and outlook 2007 migrate on same computer to domain user with outlook 2007 emails intact

    - by bifpowell
    I have Dell Laptop with windows 7 64 bit and for the last year it's been just a machine with an account like: machine\john there are files in folders and stuff in c:\users\john and john uses outlook 2007 as a pop3 client and has identifiable local appdata pst files. Now I installed a server and want to have everything be domain-centric so I added this laptop to the domain with admin credentials and then logged in as a domain user as: domain\john.smith Now I want to duplicate machine\john (outlook emails mostly) to domain\john.smith. In the past I used the Files and Settings Xfer Wizard and done. I tried that here and it crunched away for a while, made the file, but the restore had no effect - it ran for a while, had a progress bar, but it's like nothing happened at all afterwards. I've rebooted the machine, logged in as domain administrator as the first user to log on after the restart and tried: c:\users\john xcopy c:\users\john c:\users\john.smith /V /C /F /H /K /Y /E ...and it copies some of it, but when it gets to c:\users\john.smith\appdata\local\application data it chokes "Access denied, unable to create directory" I also tried logging in as domain\john.smith and copying the entire directory that the PSTs are in from machine\john and a lot of the mail was there when I launched outlook after replacing the PSTs, but not all of them??? I got errors about files in use when doing this method, which I figure must be why not all the old emails are in the inbox?... There must be some extremely simple way to do what must be a very common requirement. Any guidance appreciated.

    Read the article

  • File permissions question

    - by Matthew Robert Keable
    I just switched my site's server from Windows to Linux, and am finally able to control file permissions from my ftp. So, seeing that all permissions were 705 by default (and not wanting just anyone to have permission to execute), I went and changed everything to 744. Now, gif and jpg links don't work, pdf download links don't work, php links don't load, and mov files don't play. Conversely, all html files work perfectly. Setting things back doesn't seem to help. Even setting to 777 gets me nowhere. Any ideas on what might be going wrong? I've been googling file permissions all day (solved that problem with the Windows-Linux switch, which has bred a new problem), and I don't think anything I can find has escaped my attention. The site: absis-minas.com Go easy on a n00b. I took up learning php out of interest, and wound up delving into server management issues due to a very simple line of code not working the way it was supposed to. Thanks!

    Read the article

  • Slow boot for OS and external devices

    - by Derek Van Cuyk
    I have been having this problem intermittently but as of yesterday, it has become more consistent. It originally started when I rebooted my PC at home and the OS (Windows 8) sat in a loop appearing to do nothing while loading. I figured since this was a new installation, that something may have just become corrupted and I decided to reinstall. So I tried to boot off of the thumb drive which had the installation iso and encountered pretty much the same issue. Same with the DVD drive. So, I rebooted once again and left it to load the entire night just to see if it ever would and sure enough this morning, Windows had finally loaded. Authentication had the same roblem albeit not quite as long (took about 5 minutes to authenticate). However, once I was in, everything appeared to be working fine and as quick as normal with the exception of when I tried to scan the C drive for any errors, which ran unbearably slow (45 minutes and before I left for work and was not finished scanning a 64GB SSD drive). I mention that I have had this issue but never when loading the OS. Before it occurred when trying to install windows 7 from a different DVD drive than the one I have now. It took me about 3 hours to do it since I had to wait sometimes 30+ min for each step to finish processing. Does anyone have an idea as to what can cause this? I am assuming it is the motherboard since it is responsible for communication with all the devices I'm having issues with but I cannot find anyone else who has had a problem like this and don't want to drop more money on a MB if it isn't the problem. Hardware: Motherboard: Asus M4A78T-E Socket AM3/ AMD 790GX/ Hybrid CrossFireX Hard Drive: Kingston SSDNow V+180 64GB Micro SATA II 3GB/S 1.8 Inch Solid State Drive SVP180S2/64G Optical Drive: Samsung Blu-Ray Combo Internal 12XReadable and DVD-Writable Drive with Lightscribe SH-B123L/BSBP Thanks, Derek

    Read the article

  • Is encryption really needed for having network security? [closed]

    - by Cawas
    I welcome better key-wording here, both on tags and title. I'm trying to conceive a free, open and secure network environment that would work anywhere, from big enterprises to small home networks of just 1 machine. I think since wireless Access Points are the most, if not only, true weak point of a Local Area Network (let's not consider every other security aspect of having internet) there would be basically two points to consider here: Having an open AP for anyone to use the internet through Leaving the whole LAN also open for guests to be able to easily read (only) files on it, and even a place to drop files on Considering these two aspects, once everything is done properly... What's the most secure option between having that, or having just an encrypted password-protected wifi? Of course "both" would seem "more secure". But it shouldn't actually be anything substantial. I've always had the feeling using any kind of the so called "wireless security" methods is actually a bad design. I'm talking mostly about encrypting and pass-phrasing (which are actually two different concepts), since I won't even consider hiding SSID and mac filtering. I understand it's a natural way of thinking. With cable networking nobody can access the network unless they have access to the physical cable, so you're "secure" in the physical way. In a way, encrypting is for wireless what building walls is for the cables. And giving pass-phrases would be adding a door with a key. So, what do you think?

    Read the article

  • Enabling hardware acceleration and Xinerama for multi-monitor/multi-GPU in Linux

    - by mynameiscoffey
    My current setup is three monitors connected as follows (monitors listed from left to right): GPU0 (nVidia GTX 280): - Dell 2405FPW (1920x1200) - Dell U2410 (1920x1200) GPU1 (nVidia 210): - Dell 2405FPW (1920x1200) Works like a charm in Windows 7, not so much in Linux. I seem to only have three real options: Run all three monitors as a seperate X screen, I get hardware acceleration but as they are all independent X sessions I cannot move windows between them and can only have firefox open on one at any given time. Run the two on GPU0 in TwinView mode and have GPU1 as a seperate X screen. Same limitation as 1 but at least two monitors work together ok. I did have an issue where occasionally Linux saw both monitors on GPU0 as a single large monitor however. Enable Xinerama and have everything work as I want it to but hardware acceleration is gone and the display is Windows 95 style choppy. My ideal solution would be to have all screens working as they do under Xinerama without the limitation of having hardware acceleration disabled. I don't even care if that means rendering all three on GPU0 and somehow farming out the display of the third monitor to GPU1, whatever works. My question is this: is there any way to accomplish this? I don't feel like my use case is so out there that there shouldn't be at least some form of support (beyond the three limited options presented above), or is my best option going to be to just suck it up and pick up a better card to replace both that can handle three outputs by itself?

    Read the article

  • Mac creating files w/ wrong perms on samba share

    - by geoffjentry
    In my group, which is very heterogeneous in terms of machines, we use a samba share to collaborate on files and such. In all but one case, it works as expected (or at least close enough). The one exception is my boss' laptop, a snow leopard macbook air. On his desktop (also snow leopard), if he creates a file it ends up serverside with perms of 774, but when he creates it with the Air, the perms are 644. The key problem is the lack of group write permission on the laptop created files. What's really confusing is that everything that I've looked at on the two machines are identical - same version of OS X, same version of samba (3.0.25b-apple), same settings for the same software, etc. I can't imagine why one machine would be different than the other, but it is. To try to be complete w/ the description, here is the relevant portion of my smb.conf file: comment = my Share path = /path/to/share public = no writeable = yes printable = no force group = myshare directory mask = 0770 create mask = 0770 force create mode = 0770 force directory mode = 0770 EDIT: I looked at three more Macs and all of them worked as expected which leaves this one laptop the true oddball. This wasn't as good as a test as the others though, as they were all leopard.

    Read the article

  • nginx: SSI working on Apache backend, but not on gunicorn backend

    - by j0nes
    I have nginx in front of an Apache server and a gunicorn server for different parts of my website. I am using the SSI module in nginx to display a snippet in every page. The websites include a snippet in this form: For static pages served by nginx everything is working fine, the same goes for the Apache-generated pages - the SSI include is evaluated and the snippet is filled. However for requests to my gunicorn backend running a Python app in Django, the SSI include does not get evaluated. Here is the relevant part of the nginx config: location /cgi-bin/script.pl { ssi on; proxy_pass http://default_backend/cgi-bin/script.pl; include sites-available/aspects/proxy-default.conf; } location /directory/ { ssi on; limit_req zone=directory nodelay burst=3; proxy_pass http://django_backend/directory/; include sites-available/aspects/proxy-default.conf; } Backends: upstream django_backend { server dynamic.mydomain.com:8000 max_fails=5 fail_timeout=10s; } upstream default_backend { server dynamic.mydomain.com:80; server dynamic2.mydomain.com:80; } proxy_default.conf: proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; What is the cause for this behaviour? How can I get SSI includes working for my pages generated on gunicorn? How can I debug this further?

    Read the article

  • Keep Windows Installer from using largest drive for temporary files

    - by stefan.at.wpf
    By default Windows Installer uses the largest drive for temporary storage, no matter if that's needed (meaning there would also be enough space on the system drive). Taken from http://msdn.microsoft.com/en-us/library/aa371372%28VS.85%29.aspx: During an administrative installation the installer sets ROOTDRIVE to the first connected network drive it finds that can be written to. If it is not an administrative installation, or if the installer can find no network drives, the installer sets ROOTDRIVE to the local drive that can be written to having the most free space. Now my system drive is an SSD, my largest drive is a RAID, that spins down when it's not used. Remember the SSD as system drive? Everything is silent now! Until I install something and Windows Installer wakes up my RAID again just to put a small .tmp file on it... How can I prevent Windows Installer from using the largest drive as temporary storage? Can I maybe set some access rights to disallow the Windows Installer to write on my RAID drive? Any other ideas? Thank you!

    Read the article

< Previous Page | 515 516 517 518 519 520 521 522 523 524 525 526  | Next Page >