Search Results

Search found 25727 results on 1030 pages for 'solution'.

Page 518/1030 | < Previous Page | 514 515 516 517 518 519 520 521 522 523 524 525 | Next Page >

Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

- by user1622959

A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

Read the article
Access a PLESK website before propagation?

- by RCNeil

My web host uses Plesk and I want to know if there is anyway to access and view a website (with PHP and other processes being functional) without propagation of the domain name? I have found countless forums on this but they are all pretty old (circa 01-04) and involve either tricking your localhost or SSH commands and some even result in terrible security risks. I would like to access a web page directory through a browser and see it's contents while having the PHP processes carry out... before I propagate it's potential domain name. People claim this is pointless but during a site migration why on earth would you not test a site before propagating it? I'm looking for something similar to what cPanel offers i.e. http://IP.ADDRESS./~mydomain.com The only solution I could think of is storing the site in a new directory of an already functional site and then setting up databases and testing the site once it's complete. Once tested and working I should be easily be able to migrate the files to the "new" domain name's root directory and just setup a new databases and then propagate the domain name. I can't believe that Plesk V10+ still does not have a site preview method that includes PHP, JS, and Flash ability.

Read the article
Old laptop turns off due to overheating

- by Jake Thomas

I have an old Laptop that powers off when the processor's temperature exceeds 84degs Celsius. The more annoying part is flash causes this the most of the times. If I watch a web feed for more than 15-20mins, it results into hard shutdown of the machine. I have an idea of a could-be solution to this problem, I want a program that would decrease the processor's clock speed to about 1.2GHz or whatever, leading it a lower temperature. Is there a program out there that does this? P.S. Someone please edit this and add the relevant tags, as I'm new and i have no idea of what tags to choose from.

Read the article
Validate that a Checkbox is checked using javascript

- by H(at)Ni

I was facing a challenge yesterday that I was creating a Visual webpart and I wanted to validate the a submit button is only visible if the user checked a "I agree to terms" checkbox. Something was weired that I tested my code on a normal asp.net website and it worked perfectly while it had a different behaviour inside the webpart which is whenever I check the checkbox, the button is enabled but it will not fire the asp.net validators in client side. It posts back the page and then the validators appear after that. So, I tried to change my type of thinking and I reached a different solution is that to call a javascript function whenever the button is clicked and then check if the checkbox is clicked or not. To illustrate more, here are an example to what I'm saying: 1. Button in aspx page: <asp:Button OnClientClick="CheckForCondition();" ValidationGroup="CompaniesSection" ID="btnCompaniesSubmit" runat="server" Text="Submit" /> 2. CheckForCondition() function: <script language="javascript" type="text/javascript"> function CheckForCondition() { if ($jq('#<%= ChkCompanyCheck.ClientID %>:checked').val() == undefined) { $jq('#lblCheckBox').show(); return false; } else { $jq('#lblCheckBox').hide(); return true; } } </script> 3. lblCheckBox is simply a label that shows a red asterisk beside the checkbox to indicate that it's a required field. <label id="lblCheckBox" style="color:Red;display:none">*</label>

Read the article
Odd domain switching behavior in Firefox and Chrome

- by Jeremy Detrempe

We have different development severs and a production server. Testing is done in the development servers. As a QA engineer, I'm switching between these servers quite often throughout the day. In Chrome, sometimes I need to reload a page a few times to get it to pull from the newly switched server. In Firefox, sometimes I need to quit the browser in order to get it to pull from the newly switched server. (We have small tags that indicate which server you are pulling from, which is how I know in-browser.) Why does that happen? I'd love to know how that happens (maybe what it's called?) and what the best way to deal with it is. (I know that Firefox has an extension for domain switching; is that the best solution?)

Read the article
Hyperlink to doc file slow opening

- by mserioli

I've two excel file with inside some link to .doc and .pdf file. Both excel files and linked files are on a network shared folder. The first excel file is an .xls, the second an .xlsm. While opening link to .pdf file is very fast (the file is open in few seconds) it take a long time to open .doc files (about 40 secs.). I have searched on internet but found no solution at the moment. I have this problem with both excel 2007 and 2010. Does anyone know how to solve this problem? Thanks a lot Marco

Read the article
Real-Time chat translation on mac using either Skype, Adium or iChat

- by Cawas

If you're looking for MSN and / or Windows, just go here. I'm looking for Real-Time chat translation tools for Mac, and preferably using Adium, but it could be for Skype, iChat or maybe another option if it's really good. So far I could only easily find a plugin for Adium, simply called translator, that uses google, dicts and babelfish, but you have to type commands in and paste the words or sentences, and it's currently not even working on Snow Leopard. Even if it did, it's still not quite as automatic as we'd expect (or see in other platforms as indicated). So I'm just citing it as an example of a bad solution.

Read the article
Rename Devices in Device Manager

- by Luke

This is mostly just for the USB ports, as I recognize everything else in computers.... Anyways, is there a way to rename, or otherwise, identify which USB port (or other hardware for that matter) is which device in Device Manager? I know I can plug in a flash drive, then see what port it is connected with, and find out that way. What I would like though, is to find out that a certain plug is always a certain device in Device Manager. If I can then have a system in mind that always has the same order, I can look and see if a USB port is not being detected or not working properly, and as I uninstall/reinstall USB devices, I know I won't lose my keyboard or mouse, for example. The OS in question currently is Windows 7, but I would accept a solution for ANY version of Windows USB Devices | +--+USB Root Hub Port A | | | ---Keyboard | +--+USB Root Hub Port B | | | ---Mouse | +--+USB Root Hub Port C | ---Empty

Read the article
How to pin NetBeans to Windows 7 taskbar?

- by Vilx-

I've googled around and it seems that I'm not the only one with the problem, however I couldn't find the solution. Maybe someone around here has figured it out. The problem is that netbeans.exe is actually a stub which is calling javaw.exe. When I try to pin the NetBeans process to the taskbar I actually pin "Java(TM) Platform SE Binary". That changes the icon and the pin doesn't work. The funny thing is that it works on another machine. I don't know whether it's because it's a different version of NetBeans, or a different version of Java. Has anyone figured this out? Added: I know this is sort of not programming related; on the other hand there are plenty of topics around here about how to better your programming environment, and this one is no worse than those. Oh, and btw - Windows 7 Enterprise x64; Java JDK 1.6.17; Netbeans 6.8

Read the article
How to stop Word 2011 opening hyperlinks on click?

- by John Yeates

In previous versions of MS Word, there was a preference for the action to be taken when the user clicked a hyperlink: open it, or edit it. Word 2011 appears to have defaulted to opening the hyperlink, and I can't find the preference to change this behaviour. How can I change Word's default behaviour when a hyperlink is clicked to be editing the text of the hyperlink? Holding down a modifier key when clicking is not an acceptable solution, as the aim here is to prevent misclicks from causing web pages to open. Edit: the links need to stay as links in the saved document. But when clicked on my machine, they should not open; Word needs to default to just editing the link, so an inaccurate click does not take me out of the document into Safari. Older versions of Word had a preference controlling this, and Microsoft seem to have removed it and fixed the behaviour at the unsafe option in order to satisfy the point-and-drool crowd.

Read the article
Import virtualBox appliance to KVM

- by Hugo Bulnes

Im new using KVM as a virtualization solution. Currently I'm using VirtualBox to manage my virtual machines in my personal computer, but I'm moving my virtualization to a Server, so I set up a Linux server with KVM. And now I'm trying to import a virtualBox vm to KVM. So far I couldn't make it work. I already convert the ova file from VirtualBox to a format more familiar to KVM (qcow2), and I try to create a new virtual machine using virt-install command and setting the new virtual machine hard drive with the .qcow2 file. There is anyone could help me? thank you!

Read the article
Windows: How to add batch-script action to Right Click menu

- by ervingsb

I have a few programs that creates temp files or backup files or similar files that are not important. For example, GVim for Windows by default creates a backup file in filename.txt~. I sometimes need to clean up a dir and remove all these files. I have made a simple .bat file for this. However, it is cumbersome to have to start up cmd, navigate to the folder, run the script. Especially since this is a script that I would like to run often on various folders. And I do not want to copy the script to multiple folders, as this would be a maintenance nightmare. So, I was thinking, that the best solution would be to add a Right Click menu item that allows me to run the script. So that I can right click on a folder in Explorer and click Cleanup and then have my script run on this folder. So my question is: How do I add a right click menu action that runs a custom batch script?

Read the article
Video editing: Proper length of VOB movie not identified.

- by Roy Rico

I copied a VOB from a camcorder disc. The content is about an hour long, but in Premiere, GOM Media Player or VLC only recognizes the clip is 12 or 3 seconds long. I tried renaming the file to MPG from VOB with no luck. Is there anything that can fix this solution? Update: Thanks for the suggestions. The VOB files in question are the specific videos I'm looking for. The files are complete copies (same size), and play in all the video players to full length. They just have a end time of 3 (or 12) seconds, so the playback slider goes to 12, and stops, and the video continues to play.

Read the article
Can you run Android 2.2 Froyo or 2.3 Gingerbread in a VM?

- by Josh B

I came across a how-to guide for running Android 1.7 in a virtual machine (VirtualBox), but 1.7 is old. I haven't been able to find a Android 2.2 or 2.3 image anywhere, does anyone have any ideas on how to virtualize newer Android OS's? Preferably a free virtualization solution like VirtualBox. Here is the link about virtualizing 1.7: http://osxdaily.com/2010/12/14/run-android-using-a-virtual-machine-on-a-mac-or-windows-pc/ They send you to here to download Android disk images: http://virtualboxes.org/images/android-x86/ But I can't find anything newer than 1.7, anyone have any ideas? Is this considered illegal or piracy is that why there are no images available? Thanks for help!

Read the article
Disk Utility Restore causes "Could not validate resource - Invalid Argument"

- by Yahoo

I have a problem with Disk Utility on Mac OS X 10.6. I have an image of Windows that I would like to use as a bootable volume on a pen drive or external hard drive. The thing is: When I try to restore the volume from the image I get an error: "Restore Failure: Could not validate resource - Invalid Argument" I read some information about that error on the Internet. I converted the image into .iso (Mac OS Extended/ISO (Joliet) Hybrid Image) format and then got this error: "Restore Failure: Could not find any scan information. The source image needs to be imagescanned before it can be restored." When I try to scan the image for Restore, I get the first message. I really read a lot of information about this topic on the Internet, but I haven't found the solution. I tried both ISO and DMG formats; I don't know which is best.

Read the article
Mounting LVM2 volume with XFS filesystem

- by Chris

Unfortunately I'm not able to access the data on my NAS anymore. I can't figure out why this is the case as I haven't changed anything. So I plugged one of the harddisks in my computer to access the data. What I did: kpartx -a /dev/sdc Now I should be able to access /dev/mapper/vg001-lv001 When trying to mount it I get: sudo mount -t xfs /dev/mapper/vg001-lv001 /home/user/mnt mount: /dev/mapper/vg001-lv001: can't read superblock Now I did a parted -l which gave me Modell: Linux device-mapper (linear) (dm) Festplatte /dev/mapper/vg001-lv001: 498GB Sektorgröße (logisch/physisch): 512B/512B Partitionstabelle: loop Number Begin End Size Filesystem Flags 1 0,00B 498GB 498GB xfs Does anybody have a solution how to recover the data?

Read the article
Domain Transfer Protection - need advice

- by Jack

Hey, I am about to purchase a domain name for a bit of money. I do not personally know the person who I am purchasing the domain name from, we have only chatted via email. The proposed process for the transfer is: The owner of the domain lowest the domain name security and emails me the domain password, I request the transfer After the request, I transfer the money via PayPal When the money has been cleared the current domain name owner confirms the transfer via the link that he receives in that email I wait for it to be transferred. The domain is currently registered with DirectNIC - http://www.directnic.com/ Is this the best practice? Seeing I am paying a bit of money for this domain name, I am worried that after the money has been cleared that I won't see the domain name or hear from the current domain name owner again. Is there a 'domain governing body' which I can report to if this is the case? Is the proposed transfer process the best solution? Any advice would be awesome. Thanks! Jack

Read the article
Howto maintain an EXT3 filesystem

- by Reinoud van Santen

Lately I had several servers which encountered a write error on an EXT3 filesystem and as a result of that remounted the filesystem read-only. Understandably on a production server this causes severe problems. On a reboot the filesystem where fixed but on large partitions this takes a lot of time. After the filesystem was fixed, correcting several errors, the server runs well again. What can I do to minimize the rate at which this happens? I can't seem to find much information on periodically checking the filesystem(s) on a running server. Is it possible to change the way in which EXT3 / the system handles write errors? What would be a sane solution. All servers which this is regarding to are running CentOS Linux 5.4 or 5.5.

Read the article
Is it possible to combine two internet connections to increase performance?

- by cornjuliox

I've got a small home network, 3 PCs plus a laptop or two when the relatives come to visit, connected to a single cable internet connection. Now, as soon as everyone starts using the 'net the performance starts to suffer and if the load is heavy enough nobody can get anything done and everyone complains. At one point it was so bad that only one of us could use it at a time. I was researching possible solutions to this problem and I heard that internet cafes that utilize 2 internet connections, possibly from different providers, and have some sort of router that allows them to split the traffic between the both of them, with online games going through one and web traffic going through another. Is this possible? What is the technical term for it, and can/should it be applied to a home network setup or is there another solution to this problem?

Read the article
Why do I get "Permission denied (publickey)" when trying to SSH from local Ubuntu to a Amazon EC2 se

- by Vorleak Chy

I have an instance of an application running in the cloud on Amazon EC2 instance, and I need to connect it from my local Ubuntu. It works fine on one of local ubuntu and also laptop. I got message "Permission denied (publickey)" when trying to access SSH to EC2 on another local Ubuntu. It's so strange to me. I'm thinking some sort of problems with security settings on the Amazon EC2 which has limited IPs access to one instance or certificate may need to regenerate. Does anyone know a solution?

Read the article
securing unpatched websites

- by neuron

I have a client with a lot (read several thousand) websites in several old cms solutions that are no longer maintained. Now moving all of them to a maintained solution isn't really an option at this point. So I'm thinking about ways to secure the solutions without patching them. The solutions are mostly joomla 1.0/1.5 and wordpress. What I'm thinking is something like this: mod_suexec to lock everyone into their own home directory apparmor to deny any and all file writes by default. (exclude by default, include things like "images" directories). use htaccess to prevent anything in writable directories from being executed. (aka disable php_engine for images/ directory). mysql triggers to check the "users" tables to prevent adding new admins/superadmins. Does this make sense? Is it viable? Am I missing something obvious?

Read the article
Migrating My GWB Blog Over To WordPress

- by deadlydog

Geeks With Blogs has been good to me, but there are too many tempting things about Word Press for me to stay with GWB. Particularly their statistics features, and also I like that I can apply specific tags to my posts to make them easier to find in Google (and I never was able to get categories working on GWB). The one thing I don’t like about WordPress is I can’t seem to find a theme that stretches the Content area to take up the rest of the space on wide resolutions…..hopefully I’ll be able to overcome that obstacle soon though. For those who are curious as to how I actually moved all of my posts across, I ended up just using Live Writer to open my GWB posts, and then just changed it to publish to my WordPress blog. This was fairly painless, but with my 27 posts it took probably about 2 hours of manual effort to do. Most of the time WordPress was automatically able to copy the images over, but sometimes I had to save the pics from my GWB posts and then re-add them in Live Writer to my WordPress post. I found another developers automated solution (in alpha mode), but opted to do it manually since I wanted to manually specify Categories and Tags on each post anyways. The one thing I still have left to do is move the worthwhile comments across from the GWB posts to the new WordPress posts. The largest pain point was that with GWB I was using the Code Snippet Plugin for Live Writer for my source code snippets, and when they got transferred over to WordPress they looked horrible. So I ended up finding a new Live Writer plugin called SyntaxHighlighter that looks even nicer on my posts If anybody knows of a nice WordPress theme that stretches the content area to fit the width of the screen, please let me know. All of the themes I’ve found seem to have a max width set on them, so I end up with much wasted space on the left and right sides. Since I post lots of code snippets, the more horizontal space the better! So if you want to continue to follow me, my blog's new home is now at https://deadlydog.wordpress.com

Read the article
HDMI Audio drops out when display enters powersave

- by Jared Tritsch

I have a Windows 8 machine with an AMD APU attached to my Home Theater system through HDMI (HDMI routes through a Home Theater AMP, then into the TV). Here's my problem, Whenever the display is interrupted, usually by the TV being turned off or into powersave mode, the audio device lists as "Disconnected" in windows audio devices and I cant get it to re-recognize that the HDMI audio is, in fact, plugged in. The only solution I have found so far is to restart the machine, which will then recognize the device without any problems, until the next time the TV turns off and the problem once again resurfaces. Has anyone else seen this phenomenon? I have no idea if its the GPU, the HDMI interface, the AMP, or even the TV itself, as there really isn't much a way to tell...

Read the article
How do you keep SOA DRY?

- by TaylorOtwell

In our organization, we've shifted to a more "service oriented architecture". To give an example, let's assume we need to retrieve a "Quote" object. This quote has a shipper, a consignee, phone numbers, contacts, email addresses, and other location information. In other words, a Quote object is made up of many other objects. So, it seems like it would make sense to make a "Quote Retrieval Service". In our situation, we've accomplished this by creating a .NET solution and writing the service. The service API looks something like this (in pseudo-code): Function GetQuote(String ID) Returns Quote So, so far so good. Now, when this service is consumed, to keep things "de-coupled", we are creating essentially a duplicate of the Quote object and mapping from the QuoteService version of the Quote into the consumer's version of the Quote. In many cases, these classes will have the exact same properties. So, if the Quote service is consumed by 5 other applications, we would have 6 definitions of what a "Quote" is. One for each consumer, and one for the service. This feels wrong. I thought code was supposed to be DRY, but it seems like our method of SOA is forcing us to create tons of duplicated class definitions. What are we doing wrong, or is the code duplication just a "necessary evil" of SOA?

Read the article
What's the best way to manage reusable classes/libraries separately?

- by Tom

When coding, I naturally often come up with classes or a set of classes with a high reusability. I'm looking for an easy, straight-forward way to work on them separately. I'd like to be able to easily integrate them into any project; it also should be possible to switch to a different version with as few commands as possible. Am I right with the assumption that git (or another VCS) is best suited for this? I thought of setting up local repositories for each class/project/library/plugin and then just cloning/pulling them. It would be great if I could reference those projects by name, not by the full path. Like git clone someproject. edit: To clarify, I know what VCS are about and I do use them. I'm just looking for a comfortable way to store and edit some reusable pieces of code (including unit tests) separately and to be able to include them (without the unit tests) in other projects, without having to manually copy files. Apache Maven is a good example, but I'm looking for a language-independent solution, optimally command-line-based.

Read the article

< Previous Page | 514 515 516 517 518 519 520 521 522 523 524 525 | Next Page >