Search Results

Search found 16902 results on 677 pages for 'strange errors'.

Page 518/677 | < Previous Page | 514 515 516 517 518 519 520 521 522 523 524 525  | Next Page >

• Backup Exec 10 - Network connection to the remote agent has been lost

  - by jherlitz

  Okay, so I have 4 remote offices, all running off of a 3mb ethernet connection. Two sites are part of a WAN and 2 sites are using 3mb connections over a site to site tunnel. I am using Backup Exec 2010, I have the remote agent installed on all the remote servers. For the past few weeks now, on the two sites running over the site to site tunnel have been failing with the following error message now. "The network connection to the Backup Exec Remote Agent has been lost. Check for network errors" We used to be on a DSL connection site to site tunnel, now we changed to the 3mb ethernet connection using site to site tunnel. I have to find out, has it been failing ever since we changed, or just recently. Backup exec support is telling me it is a network issue. My communication or connection to the server is solid, we don't have any issues, or outages. So I am baffled on why this continues to fail. And why just those two sites.. Any advice?

  Read the article

• Hyper-v on 2012R2 startup gen1 vm causes the host to freeze up

  - by sputnik

  I've searched a lot to resolve the following issue, but nothing helped me. My problem is, that starting up a first-gen vm locks up the whole host. Only a hard reset helps. Second-gen vm starts and runs perfectly. The freezes happened on 3 different vms. FreeBSD, Ubuntu, Windows Server 2008R2, while Windows 8.1 on second gen config works perfectly. Im using this pc mainly as a workstation. No eventlog errors nor dumps are generated. My system: Windows Server 2012R2 FX-8350, non OC ASRock 870 Extreme R2 (Crappy board imho) 32GB DDR3 1866@1600 (My motherboard, against the "support" for 1866ram won't work with full speed) 120GB SSD 4.5TB Storage space device I dont think that its due to my system, because vmware workstation was running without problems. Did I forget to configure something? Any help is appreciated. P.S: Even deactivating C1E, C6, C&Q didnt work. P.P.S: With no virtual network adapter set, the system still locks up. Creating a first gen vm without any hdds and network and launching works. Attaching a boot dvd causes the host to freeze. The host freezes as the gen1 vm begins to boot, doesn't matter if from dvd or hdd

  Read the article

• MD RAID 1 with external bitmap doesn't fully resync

  - by user64744

  I have an interesting configuration: dual boot system with a RAID 1 that needs to be visible in both Windows and Linux. The Windows install is Win 7 Enterprise, and the Linux install is Kubuntu 10.04. To get the RAID to work, I set it up using Windows's "Dynamic Disks" RAID 1, and brought it up in Linux using MD with no persistent superblock, and a write-intent bitmap on another partition. (Without this bitmap, MD had no way of knowing that the array was in sync, and would do a complete resync every time the array started.) The array is assembled like so: mdadm --build /dev/md1 -l 1 -n 2 -b /var/local/md1.bitmap /dev/sdb2 /dev/sdc2 I expected that the first time I ran this command, it would resync the array, write out a bitmap with no dirty chunks, and all would be good. This wasn't the case: after completing the resync, the bitmap was mostly clean, but about 5% dirty blocks remained, as revealed by mdadm -X /var/local/md1.bitmap I didn't mount the filesystem on /dev/md1 or touch it in any other way. I then found that stopping and restarting the array: mdadm --stop /dev/md1 mdadm --build /dev/md1 -l 1 -n 2 -b /var/local/md1.bitmap /dev/sdb2 /dev/sdc2 did indeed read in the bitmap, with an ensuing resync that went quickly because most of the blocks were marked clean. The confusing part is that this resync further reduced the number of dirty blocks, but still did not remove all of them. By repeatedly stopping and restarting I could slowly bring the dirty block count down to around 0.6%, where it seemed to level out. Any ideas what could be causing this? It smells to me of a race condition somewhere that leads to blocks either being skipped over during synchronization or not properly cleared from the bitmap, but I really have no evidence to prove this. It doesn't look like hardware issues since both drives are new and have zero read errors and reallocated sectors reported by smartctl -a.

  Read the article

• Exchange 2013 attachments too big?

  - by KPS

  I am having the toughest time sending large attachments, everywhere I have checked my file size limit for send/receive is 100mb but yet users are unable to receive files even at the size of 14mb. I'm using a spam filter (Appriver) and have worked with there support for a very long time, we see the following errors in logs 13:32:40.260 4 SMTP-000036([myserverIP]) rsp: 354 Start mail input; end with <CRLF>.<CRLF> 13:33:41.038 3 SMTP-000033([myserverIP]) write failed. Error Code=connection reset by peer 13:33:41.038 3 SMTP-000033([myserverIP]) [659500] failed to send. Error Code=connection reset by peer 13:33:41.038 4 SMTP([myserverIP]) [659500] batch reenqueued into tail Windows firewall is disabled on the exchange server, all other emails that are of smaller value come through just fine. Here is a print out of size limits: ConnectorType ConnectorName MaxReceiveMessageSize MaxSendMessageSize ------------- ------------- --------------------- ------------------ Send InternetSendConnector - 35 MB (36,700,160 bytes) Send Appriver-Smarthost - 35 MB (36,700,160 bytes) Receive Default EXCHSRVR 100 MB (104,857,600 bytes) - Receive Client Proxy EXCHSRVR 100 MB (104,857,600 bytes) - Receive Default Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive Outbound Proxy Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive Client Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive ExchangeRelay 100 MB (104,857,600 bytes) - TransportConfig - 100 MB (104,857,600 bytes) 10 MB (10,485,760 bytes) ADSiteLink DEFAULTIPSITELINK Unlimited Unlimited There is a no anti-virus on the server either that could be interfering, I am out of ideas at this point :( EDIT 1 After running BPA, it gives and error: Exchange Organization: Check whether the incoming message(CN=MyDomain,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=WG,DC=local) size isn't set The maximum incoming message size isn't set in organization 'CN=MyDomain,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=WG,DC=local'. This can cause reliability problems. Here are the sizes as of now: [PS] C:\Temp>Get-TransportConfig | ft MaxSendSize, MaxReceiveSize MaxSendSize MaxReceiveSize ----------- -------------- Unlimited Unlimited [PS] C:\Temp>Get-ReceiveConnector | ft name, MaxMessageSize Name MaxMessageSize ---- -------------- Default EXCHSRVR 100 MB (104,857,600 bytes) Client Proxy EXCHSRVR 100 MB (104,857,600 bytes) Default Frontend EXCHSRVR 100 MB (104,857,600 bytes) Outbound Proxy Frontend EXCHSRVR 100 MB (104,857,600 bytes) Client Frontend EXCHSRVR 100 MB (104,857,600 bytes) ExchangeRelay 100 MB (104,857,600 bytes) Again, smaller emails come through just fine. Seems like there is a 10mb receive limit somewhere that I cannot find.

  Read the article

• WAMP server won't run with PHP 5.3.4 but will with PHP 5.2.11

  - by Ben Williams

  I have a 64bit Windows 7 Professional machine. I'm running WampServer Version 2.1 with Apache 2.2.4. It was installed on a clean machine. I'm using the default ini/conf files as they come. Wamp is installed in C:\wamp\, with php5.2 at C:\wamp\bin\php\php5.2.11 and php5.3 at C:\wamp\bin\php\php5.3.4. Both folders have the same permissions. When I run WAMP with 5.2.11 picked, it starts fine. When I run it with 5.3.4 picked, there are no errors in the Apache or PHP error logs, but I get The Apache service named reported the following error: httpd.exe: Syntax error on line 115 of C:/wamp/bin/apache/apache2.2.4/conf/httpd.conf: Cannot load C:/wamp/bin/php/php5.3.4/php5apache2_2.dll into server: The Apache service named is not a valid Win32 application. in my system application error logs. 5.2.11 calls C:/wamp/bin/php/php5.2.11/php5apache2_2.dll and that doesn't throw an error. What am I doing wrong?

  Read the article

• Webserver max CPU when apache and MYSQL are ran together

  - by Tim

  This website has been running fine without issues, Recently it went down. After some investigation it looks like the combo of MYSQL and Apache bring the box to its knees. Apache can run find serving static web pages and MYSQL can run fine when the website isn't working. As soon as the website is enabled with SQL running the CPU on the box remains at 100%. Picture of the usage: http://i.stack.imgur.com/GG2NC.png I've checked the sql database for errors, tried tuning nearly every parameter in apache/sql's conf file for performance. The server is a redhat based box running the latest software packages. Any help/suggestions are welcome. Doing an strace on a high cpu apache process I see the following: read(14, "", 8192) = 0 close(14) = 0 socket(PF_FILE, SOCK_STREAM, 0) = 14 fcntl64(14, F_SETFL, O_RDONLY) = 0 fcntl64(14, F_GETFL) = 0x2 (flags O_RDWR) connect(14, {sa_family=AF_FILE, path="/var/lib/mysql/mysql.sock"...}, 110) = 0 setsockopt(14, SOL_SOCKET, SO_RCVTIMEO, "\2003\341\1\0\0\0\0", 8) = 0 setsockopt(14, SOL_SOCKET, SO_SNDTIMEO, "\2003\341\1\0\0\0\0", 8) = 0 setsockopt(14, SOL_IP, IP_TOS, [8], 4) = -1 EOPNOTSUPP (Operation not supported) setsockopt(14, SOL_SOCKET, SO_KEEPALIVE, [1], 4) = 0 Here is what I see from a mysql process: futex(0x86fc9a4, FUTEX_WAIT_PRIVATE, 39, NULL) = 0 futex(0x86fc734, FUTEX_WAIT_PRIVATE, 2, NULL) = 0 futex(0x86fc734, FUTEX_WAKE_PRIVATE, 1) = 0 gettimeofday({1301465020, 141613}, NULL) = 0 clock_gettime(CLOCK_REALTIME, {1301465020, 141699633}) = 0 futex(0x8707a64, FUTEX_WAIT_PRIVATE, 1, {4, 999913367}) = 0 futex(0x8707a40, FUTEX_WAIT_PRIVATE, 2, NULL) = 0 futex(0x8707a40, FUTEX_WAKE_PRIVATE, 1) = 0 exit_group(0) = ?

  Read the article

• Why is lighttpd and fastcgi keeping sending me the *.scgi file instead of the website content?

  - by e-satis

  I have the following config: server.modules = ( "mod_compress", "mod_access", "mod_alias", "mod_rewrite", "mod_redirect", "mod_secdownload", "mod_h264_streaming", "mod_flv_streaming", "mod_accesslog", "mod_auth", "mod_status", "mod_expire", "mod_fastcgi" ) [...] fastcgi.server = ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/var/tmp/lighttpd/php-fastcgi.socket" + var.PID, "max-procs" => 1, "kill-signal" => 9, "idle-timeout" => 10, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "200", "PHP_FCGI_MAX_REQUESTS" => "1000" ), "/pyapps/essai/blondes.fcgi" => ( "main" => ( "socket" => "/var/tmp/lighttpd/django-fastcgi.socket", ), ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" ))) [...] $HTTP["host"] =~ "(^|www\.)cam\.com(\:[0-9]*)?$" { server.document-root = "/home/cam/web/" accesslog.filename = "/home/cam/log/access.log" server.errorlog = "/home/cam/log/error.log" server.follow-symlink = "enable" # files to check for if .../ is requested server.indexfiles = ( "index.php", "index.html", "index.htm", "index.rb") url.rewrite = ( "^(/blondes/.*)$" => "/pyapps/essai/blondes.fcgi$1" ) } I have the following dir tree: /home/tv/web/ `-- pyapps `-- essai `-- __init__.py `-- blondes.fcgi `-- blondes.pid `-- django-fcgi.py `-- manage.py `-- manage.pyo `-- plop `-- settings.py `-- urls.py No error when restarting lighthttpd. The I run: ./manage.py runfcgi method=prefork socket=/var/tmp/lighttpd/django-fastcgi.socket daemonize=false pidfile=blondes.pid No errors neither. I then go to http://cam.com/blondes/. I offers me to download an empty file. I checked permissions but everything is set to the same user and group, and they work for the PHP site. The file /var/tmp/lighttpd/django-fastcgi.socket exists. When I reload the page, I got no output in error logs, nor in the manage.py runfcgi command. I probably missed something obvious, but what ?

  Read the article

• android geting data from sql

  - by sagar

  Hello i m new to android. i wont to connect to sql server for store and get data so so me one can help me sending code of android for do it.. i had tried to do tht with java nd it was workink but now i wont to create a aplication for android my java code is :: import java.sql.*; public class MysqlTest { public static void main (String[] args) { Connection conn = null; try { String userName = "pietro"; //change it to your username String password = "pietro"; //change it to your password String url = "jdbc:mysql://192.168.0.67:3306/registro"; Class.forName("com.mysql.jdbc.Driver").newInstance(); conn = DriverManager.getConnection(url, userName, password); Statement s = (Statement) conn.createStatement(); // code for create a tabel in server s.execute("create table School2 (rolno integer,sub text)"); // code for create a tabel in server s.execute("insert into School2(rolno,sub)values(10,'java')"); //code for add value in tabel s.execute("select rolno,sub from School2");//code for add value in tabel s.close(); System.out.println("Database connection established"); } catch (Exception e) { System.err.println("Cannot connect to database server"); } finally { if (conn != null) { try { conn.close (); System.out.println("Database connection terminated"); } catch (Exception e) { /* ignore close errors */ } } } } }

  Read the article

• Exchange SBS 2003 server stopped receiving mail over the weekend, senders getting "Relay access deni

  - by Charlie W.

  Firstly, I should say that I know my way around Windows very well, I don't really know the first thing about Exchange. I am trying to support a user that is running an SBS2003 Server with Exchange. Over the weekend, everyone sending something to any of his addresses gets an error message like the following: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 5.7.1 <[email protected]>: Relay access denied (state 14). ----- Original message ----- Received: by 10.114.18.7 with SMTP id 7mr5572745war.127.1275423472120; Tue, 01 Jun 2010 13:17:52 -0700 (PDT) MIME-Version: 1.0 Sender: [email protected] Received: by 10.143.10.15 with HTTP; Tue, 1 Jun 2010 13:17:32 -0700 (PDT) From: My Name <[email protected]> Date: Tue, 1 Jun 2010 15:17:32 -0500 X-Google-Sender-Auth: XiPrP8Em_6Eb94EH9m84nJVGvCY Message-ID: <[email protected]> Subject: TEST To: Client <[email protected]> Content-Type: multipart/alternative; boundary=001636b1484ffe72470487fdaa5b There are a host of errors in the Application log, but nothing that leaps out at me as being obvious. But then again, I don't really know what I'm looking for. Any help would be greatly appreciated.

  Read the article

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  I recently did a full upgrade of Windows 7 on my Thinkpad. Everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen before the Windows logo appears. Disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this won't boot with battery plugged in is greatly appreciated. I need to take this battery out on the road/trains, etc. A little more detail on this story. The battery I had inserted when doing the (failed) boot was a long life battery. I have not tried inserting this battery when Windows is logged in. I have another (normal life) battery that I have charged up within Windows. It has just got to 100% and I am about to reboot with it in. I am using the Lenovo power manager to diagnose the battery - all seems OK. I will report back shortly as to the outcome. OK, so I chose the reboot option from within Windows, the machine seemed to shutdown okay, but then stalled. It didn't turn off completely and didn't reboot, but just sat, with the fan humming, somewhere in between! I had to hold the power button in for a few seconds until the fan stopped and then hit the power button again to boot the machine from fresh. One good thing, with this battery (the normal one) it booted into Windows 7 the first time with a battery! So, now I have rebooting issues. I have 3 errors in the event log: A timeout was reached (30000 milliseconds) while waiting for the lxdxCATSCustConnectService service to connect. The lxdxCATSCustConnectService service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. The following boot-start or system-start driver(s) failed to load: cdrom Any thoughts?

  Read the article

• Apache error "child pid XXXX exit signal exceeded file size limit (25)"

  - by Stephen Melrose

  Morning all, Apache on our internal development server stopped working last night. It's running, but all we get is a blank screen, no server errors. Examing the error log shows the following, [Fri Apr 23 09:13:57 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:03 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:03 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) [Fri Apr 23 09:14:06 2010] [notice] child pid XXXX exit signal exceeded file size limit (25) After some Googling, we found that this is due to Apache trying to handle a file greater than it's maximum allowed limit, which by default is 2GB and is usually an error log. I did a search using find . -size +1000000k -ls (find all files greater than 1GB) in our log and web folders, but nothing showed up. I've also restarted Apache and rebooted the server itself serveral times. I've completely wiped the log folder and started a fresh. Nothing is working. Any ideas as to what else might be causing this? Thank you

  Read the article

• Windows and file system abstraction - how much does it matter where something comes from?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Bootcamp driver package includes file system drivers (right term?) that enable Windows to access the Mac OS HFS+ partition. AFAIK it's a read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• ISA 2000 and COD MW2 Steam

  - by twlichty

  OK, so maybe not the "proper use" of network resources, but we enjoy the odd COD game during lunch hours. When we played COD4, we had a dedicated server setup at the back of the server room. With MW2, we need to be able to connect to steam to be able to play multi-player. I've found this support article here: https://support.steampowered.com/kb%5Farticle.php?ref=8571-GLVN-8711 Which outlines all the ports I need to open. I went through and created the following rules in ISA 2000 (I'm stuck with 2000 for now). Protocol Definition: Steam Primary connection: Port 27000, UDP, Send Receive Secondary Connection: Port range 27001-27030 Send Receive Protocol Definition: Steam TCP In Primary connection: 27014, TCP, Inbound Secondary Connection: Port range: 27015-27050, Inbound Protocol Definition: Steam 4380 Primary connection: 4380, UDP, Send Receive When I start steam on my local workstation (I did add an exception to the Vista Firewall to allow steam), the steam client sits on "Updating Steam" for 5 minutes then errors out with: You must connect to the internet first. Any ideas? I assume I missed something. Thanks for your help.

  Read the article

• Weird caching bug where old version of the same web page (same filename) is still called (Windows 2008 R2, Tomcat 5.5)

  - by user717236

  This is definitely one of the strangest errors I've seen and it occurs intermittently. I am running Windows 2008 R2, IIS 7.5, and Apache Tomcat 5.5, by the way. Let's say I have two machines, A and B. Both A and B are running Windows 2008 R2. I have a web page called login.jsp on machine A, and I have a newer, modified version of login.jsp on machine B . Now, I copy the new login.jsp from machine B and paste it to machine A, replacing the older version with the same filename. For whatever reason, when I hit up the web page in my browser from a local machine (i.e. my laptop), it still recalls the old version of the web page, even though it's been replaced! I tried restarting IIS and Apache Tomcat. That didn't work. I tried restarting machine A and that didn't work. I tried a cold reboot of my local machine and that didn't work, either. So, I spoke to someone I can confide in for help. He said to open the login.jsp page in notepad, put a space in, save the file, and try again. Sure enough, it worked. He said he hasn't seen it in Windows 2003, but this is occurring with Windows 2008. What I don't understand is why did it work and what the heck is this error and I do I really diagnose it and resolve it for good, instead of the hack my colleague proposed? Is this bug related to Windows 2008, Windows 2008 R2, Tomcat, or something else entirely? Anyone else have the same problem? Thank you for any help.

  Read the article

• SQL Server Reporting Services - website blank, builder works

  - by Keith

  We have a few reports in SQL Server Reporting Services. For some reason when we run the report from the website, it doesn't return any data. When I run the same report from the Report Builder, it returns data. I looked in the logs and the only errors I could find is: ReportingServicesService!library!8!6/15/2012-08:12:33:: i INFO: Current DB Version Unknown, Instance Version C.0.8.54. ReportingServicesService!library!8!6/15/2012-08:12:33:: e ERROR: Throwing Microsoft.ReportingServices.Diagnostics.Utilities.InvalidReportServerDatabaseException: The version of the report server database is either in a format that is not valid, or it cannot be read. The found version is 'Unknown'. The expected version is 'C.0.8.54'. To continue, update the version of the report server database and verify access rights., ;Info: Microsoft.ReportingServices.Diagnostics.Utilities.InvalidReportServerDatabaseException: The version of the report server database is either in a format that is not valid, or it cannot be read. The found version is 'Unknown'. The expected version is 'C.0.8.54'. To continue, update the version of the report server database and verify access rights. ReportingServicesService!library!8!6/15/2012-08:12:33:: e ERROR: Exception caught while starting service. Error: Microsoft.ReportingServices.Diagnostics.Utilities.InvalidReportServerDatabaseException: The version of the report server database is either in a format that is not valid, or it cannot be read. The found version is 'Unknown'. The expected version is 'C.0.8.54'. To continue, update the version of the report server database and verify access rights. I'm not really sure why it would be a different version. It's all SQL Server 2008 R2 and I haven't made any changes to it since it's been running.

  Read the article

• gcc built by crosstool-ng gives undefined reference

  - by netvope

  I've successfully built a toolchain using crosstool-ng with the default configuration named x86_64-unknown-linux-gnu. The documentation says: Using the toolchain is as simple as adding the toolchain's bin directory in your PATH, such as: export PATH="${PATH}:/your/toolchain/path/bin" and then using the target tuple to tell the build systems to use your toolchain: ./configure --target=your-target-tuple or make CC=your-target-tuple-gcc or make CROSS_COMPILE=your-target-tuple- and so on... I followed the instructions and attempted to build GNU tar (tar-1.25.tar.bz2) with the toolchain. The commands ./configure --target=x86_64-unknown-linux-gnu and make CROSS_COMPILE=x86_64-unknown-linux-gnu- do not work (the build will succeed, but it uses the host system's gcc). The command make CC=x86_64-unknown-linux-gnu-gcc works, but in the very last step when it tries to link, it returns errors like this: compare.o: In function `openat': /dev/shm/x-tools/x86_64-unknown-linux-gnu/x86_64-unknown-linux-gnu/sys-root/usr/include/bits/fcntl2.h:134: undefined reference to `__openat_2' What could be the problem? Was the toolchain not properly setup? Perhaps x86_64-unknown-linux-gnu-gcc is using the header files from the host system but could not find the libraries in the target's sys-root?

  Read the article

• MSSQL error: consistency-based I/O error - can it be caused by an MSSQL or OS problem?

  - by Philipp Keller

  This is what I saw in the windows error log: SQL Server detected a logical consistency-based I/O error: incorrect checksum (expected: 0x19fedd20; actual: 0x19fed5e3). It occurred during a read of page (1:1764) in database ID 6 at offset 0x00000000dc8000 in file 'D:\mssql\local_repository_pbdiffimport.mdf'. Additional messages in the SQL Server error log or system event log may provide more detail. This is a severe error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC CHECKDB). This error can be caused by many factors; for more information, see SQL Server Books Online. I ran dbcc checkdb which told me I should restore with option REPAIR_ALLOW_DATA_LOSS, so I eventually ran DBCC CHECKDB (my_db_name, REPAIR_ALLOW_DATA_LOSS) WITH NO_INFOMSGS But that resulted in about 2'000 rows being lost. I restored a backup but now I'm afraid this will happen again since we already had a consistency problem in the same database about 2 weeks ago but then it happened in an index (recreated indexes solved the problem). We have investigated the discs - RAID5 looks good, no errors, and also none of the disc-check-utilities have revealed any hardware problem. Can this be caused by OS (Windows Server 2003) or by MSSQL (MSSQL Server 2005)?

  Read the article

• Substiting a line through PHP in SSH

  - by Asad Moeen

  I've already setup SSH usage in PHP and most of the things work. Now what I want to do is that I'm looking to edit a line in a file and replace it back. It works directly on the server but can't seem to get it working with PHP files. Here is what I'm trying. $new_line1 = 'Line $I want to add - The $I has to go into the file as it is'; $new_line2 = 'Ending $text of the line - $text again goes into file; $query = "Addition to line"; $exec1= 'cd /root; perl -pe "s/.*/' ; $exec2= '/ if $. == 37" Edit.sh > Edited.sh'; $new="$exec1$new_line1$query$new_line2$exec2"; $edit="cd /root/mp; cp Edited.sh Edit.sh"; echo $ssh->exec($new); echo $ssh->exec($edit); Now the thing is that running the perl command directly in SSH works without any errors but when I run this through PHP I get the error: Substitution replacement not terminated at -e line 1. I want to know why would it work this way and not that?

  Read the article

• Stop the constant random reboots of my GIGABYTE GA-B75M-D3V

  - by Frederic

  I've got some issues with a new system. It's rebooting constantly. The system consists of a: brand new: Gigabyte GA-B75M-D3V with F9 BIOS (latest) Intel Core i5-3470 Ivy Bridge 2x 8GB G.SKILL Ripjaws 1600MHz memory (mem-tested x-86) coming from a stable system: Creative Soundcard X-FI Titanium Asus Radeon HD4850 OCZ Vertex 3 120G SSD Sata 3 Hard disk 1TB Sata 2 ASUS Blu-ray Drive PSU 400w Connected peripherals : Toshiba tv (displayport on dvi of MB or HD4850) Wired mouse, wireless keyboard (logitech) Bluetooth usb key Azio main problem : it's not possible to read the errors from the MB. nothing on the manual neither on internet. At the beginning, I received a MB with graphic problems and the problem of rebooting. I RMA'd it. The new one doesn't have any graphic problems. but it's still constantly rebooting. I removed everything except the HD, the sound-card, the blu-ray drive and the wireless keyboard. It's still unexpectdly rebooting. I'm running a test with just the motherboard and the HD. I will update this text after the test. I've got some questions : Somebody have an idea of a test? The PSU could cause that problem? I used it a lot of years with the stable system. Update 1: BTW, if anyone has the same problem, the manual won't say it but you'll need to reset the bios between two tests (the screwdriver on the two pins) if you suspect a problem of compatibility .

  Read the article

• SVN Authentication with LDAP and Active Directory

  - by Alex Holsgrove

  I am having a few problems getting SVN authentication to work with LDAP / Active Directory. My SVN installation works fine, but after enabling LDAP in my apache vhost, I just can't get my users to authenticate. I can use a selection of LDAP browsers to successfully connect to Active Directory, but just can't seem to get this to work. SVN is setup in /var/local/svn Server is svn.domain.local For testing, my repository is /var/local/svn/test My vhost file is as follows: <VirtualHost *:80> ServerAdmin [email protected] ServerAlias svn.domain.local ServerName svn.domain.local DocumentRoot /var/www/svn/ <Location /test> DAV svn #SVNListParentPath On SVNPath /var/local/svn/test AuthzSVNAccessFile /var/local/svn/svnaccess AuthzLDAPAuthoritative off AuthType Basic AuthName "SVN Server" AuthBasicProvider ldap AuthLDAPBindDN "CN=adminuser,OU=SBSAdmin Users,OU=Users,OU=MyBusiness,DC=domain,DC=local" AuthLDAPBindPassword "admin password" AuthLDAPURL "ldap://192.168.1.6:389/OU=SBSUsers,OU=Users,OU=MyBusiness,DC=domain,DC=local?sAMAccountName?sub?(objectClass=*)" Require valid-user </Location> CustomLog /var/log/apache2/svn/access.log combined ErrorLog /var/log/apache2/svn/error.log </VirtualHost> In my error.log, I don't seem to get any bind errors (should I be looking elsewhere?), but just the following: [Thu Jun 21 09:51:38 2012] [error] [client 192.168.1.142] user alex: authentication failure for "/test/": Password Mismatch, referer: http://svn.domain.local/test/ At the end of "AuthLDAPURL", I have seen people using TLS and NONE but neither seem to help in my case. I have the ldap modules loaded and have checked as much as I know, so any help would be most welcome. Thanks

  Read the article

• Updating Samba From RPMs

  - by KnickerKicker

  My Red Hat Enterprise Edition 4 comes with Samba Version 3.0.10, which does not have support for the "inherit owner" attribute that is essential in implementing a Deny-Delete Write Once Read Many share (for examples, search google for a-shared-drop-box-using-samba). (BTW, if any body knows an alternative way to do it without updating samba, I'm all ears!) I am not all that comfortable building from source, and after hours of googling (no, I do not have a red hat subscription, so I cannot just run the up2date command), I found a whole bunch of rpms on http://ftp.sernet.de/pub/samba/tested/rhel/4/i386/ (Samba 3.2.15 for RHEL 4)... Next, I tried updating them with the rpm -U --nodeps command, but I got file conflict errors. So I went ahead and overwrote everything (or so I thought) by using the rpm's --force option. But no good has come of all that. /usr/sbin/smbd -V still returns the old version. As of now, rpm -qa | grep samba returns, samba3-client-3.2.15-40.el4 samba-3.0.10-1.4E.2 samba-client-3.0.10-1.4E.2 system-config-samba-1.2.21-1 samba3-3.2.15-40.el4 samba-common-3.0.10-1.4E.2 samba3-winbind-3.2.15-40.el4 I cannot remove the older ones because samba-common >= 3.0.8-0.pre1.3 is needed by (installed) gnome-vfs2-smb-2.8.2-8.2.x86_64 libsmbclient.so.0()(64bit) is needed by (installed) kdebase-3.3.1-5.8.x86_64 libsmbclient.so.0()(64bit) is needed by (installed) gnome-vfs2-smb-2.8.2-8.2.x86_64 Now thats a whole bunch of dependencies that I dare not touch :) Any and all pointer are welcome at this stage. Thanks in advance!

  Read the article

• How to install rmagick on Ubuntu 10.04?

  - by Andrew

  Here's what I've done so far: sudo apt-get install imagemagick libmagickcore-dev This did not throw any errors, so I think that ImageMagick is installed fine. Then I tried installing the gem: sudo gem install rmagick This resulted in the following error: ERROR: Error installing rmagick: ERROR: Failed to build gem native extension. /usr/bin/ruby1.8 extconf.rb checking for Ruby version >= 1.8.5... yes checking for gcc... yes checking for Magick-config... yes checking for ImageMagick version >= 6.4.9... yes checking for HDRI disabled version of ImageMagick... yes checking for stdint.h... yes checking for sys/types.h... yes checking for wand/MagickWand.h... no Can't install RMagick 2.13.1. Can't find MagickWand.h. *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/usr/bin/ruby1.8 Gem files will remain installed in /usr/lib/ruby/gems/1.8/gems/rmagick-2.13.1 for inspection. Results logged to /usr/lib/ruby/gems/1.8/gems/rmagick-2.13.1/ext/RMagick/gem_make.out What do I need to do to install rmagick on Ubuntu 10.04?

  Read the article

• Windows Feature List blank, Updates fail, system readiness tool says files are corrupt

  - by Chris T

  I tried to install IIS and to my surprise the feature/components lists was blank =[. I tried the system update readiness tool and it creates the following log: ================================= Checking System Update Readiness. Binary Version 6.1.7100.4104 Package Version 5.0 2009-09-30 23:38 Checking Deployment Packages Checking Package Manifests and catalogs. (f) CBS MUM Corrupt 0x800F0900 servicing\packages\Package_1_for_KB973540~31bf3856ad364e35~amd64~~6.1.1.0.mum Line 1: (f) CBS Catalog Corrupt 0x800B0100 servicing\packages\Package_1_for_KB973540~31bf3856ad364e35~amd64~~6.1.1.0.cat (f) CBS MUM Corrupt 0x800F0900 servicing\packages\Package_for_KB973540_RTM~31bf3856ad364e35~amd64~~6.1.1.0.mum Line 1: (f) CBS Catalog Corrupt 0x800B0100 servicing\packages\Package_for_KB973540_RTM~31bf3856ad364e35~amd64~~6.1.1.0.cat (f) CBS MUM Corrupt 0x800F0900 servicing\packages\Package_for_KB973540~31bf3856ad364e35~amd64~~6.1.1.0.mum Line 1: (f) CBS Catalog Corrupt 0x800B0100 servicing\packages\Package_for_KB973540~31bf3856ad364e35~amd64~~6.1.1.0.cat Checking package watchlist. Checking component watchlist. Checking packages. Checking component store (f) CSI Catalog Corrupt 0x800B0003 winsxs\Catalogs\efdfd17ac9909b9d81e1455d9abf291319237877c23df8a67a3f5a1f2f9e034f.cat 5fbf0b9691b..6772f1b0a58_31bf3856ad364e35_6.1.7100.4127_c2160c1f90006ee6 (f) CSI Manifest All Zeros 0x00000000 WinSxS\Manifests\amd64_microsoft-windows-mediaplayer-wmpdxm_31bf3856ad364e35_6.1.7100.4127_none_35ba254677b2a294.manifest amd64_microsoft-windows-mediaplayer-wmpdxm_31bf3856ad364e35_6.1.7100.4127_none_35ba254677b2a294 (f) CSI Manifest All Zeros 0x00000000 WinSxS\Manifests\wow64_microsoft-windows-mediaplayer-wmpdxm_31bf3856ad364e35_6.1.7100.4127_none_400ecf98ac13648f.manifest wow64_microsoft-windows-mediaplayer-wmpdxm_31bf3856ad364e35_6.1.7100.4127_none_400ecf98ac13648f Summary: Seconds executed: 240 Found 9 errors CSI Manifest All Zeros Total Count: 2 CSI Catalog Corrupt Total Count: 1 CBS MUM Corrupt Total Count: 3 CBS Catalog Corrupt Total Count: 3 How can I fix this?

  Read the article

• Word 2007 won't run, tries to reinstall, fails with error 1402.

  - by eidylon

  Okay, this problem has been plaguing this computer for a while now. We tried googling, and none of the answers found helped to solve the problem. So, I am now posting the answer here for posterity. Office 2007 Home/Student edition was installed on the computer, running Vista (32-bit). One day, Word just up and stopped working. All the other programs continued to operate as expected. But every time you would click the icon for Word, it would pop up an install dialog, with a message reading "Preparing to install...". After a few minutes of the little progress bar going and going, it errors out, and gives error 1402, something to the effect of unable to access registry key HKEY_Local_Machine\Software\Classes\.wll\.... Searching around, every answer i found had to do with reassigning the permissions on this key, giving full rights to SYSTEM or to Everyone, and propagating the changes down to all sub-keys. When ever this was attempted though, it would tell us that we were unable to access the key due to permissions, even though we had run regedit as Administrator and are logged on with an administrative account. We also tried uninstalling Office and reinstalling it, as well as doing a repair install. Both these attempts also threw the same 1402 error. Also of note was that the executable for Word (winword.exe) was MIA and no longer to be found in the Office install directory.

  Read the article

• sata hard drive failed

  - by M. Shehryar

  Dear friend, initially my dual core PC started shutdown and re-start by itself after adding 1 GB ram and up-grading the graphic card. Then refused to boot. I restored the window ghost but failed to boot. I tried to install new window but installation failed after coping the window files. tried to install old vista lonhorn. It inspected found errors, fixed them but ultimatly failed to be installed. Once again restored the ghost through acronis but failed to boot. At the end attached as slave with another pc but it was not visible. Even acronis could not see it or its partitions. Only bios can see it. It seems that no file system is available on the drive. My data on drive is very important. Please help me how to revover my data. Drive brand is Samsung, cap is 160 GB and file system was NTFS.

  Read the article

< Previous Page | 514 515 516 517 518 519 520 521 522 523 524 525  | Next Page >