Search Results

Search found 27521 results on 1101 pages for 'remote control'.

Page 524/1101 | < Previous Page | 520 521 522 523 524 525 526 527 528 529 530 531  | Next Page >

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• Is it possible to auto-mount sshfs

  - by Mark D

  Is it possible to auto-mount a remote FS using sshfs upon instantiating a proper VPN connection? Allow me to explain the scenario, I'm working remotely, to do that it helps if I can mount my home dir from a server in the office. To do that I need to vpn in. So within network manager I select the relevant VPN and connect. It connects but now I have to drop to the command line and mount my home dir on several machines. If I forget to do one machine my local dev environment isn't as efficient. I suppose I could write a quick bash script to do this but I'd rather get it running automatically when I connect.

  Read the article

• Useful git commit messages for merged branches

  - by eykanal

  As a follow-up to this question: If I'm working on a team by myself, I can maintain useful commit messages when merging branches by squashing all the commits to a single diff and then merging that diff. That way I can easily see what changes were introduced in the branch, and I have a single summary describing the feature/change/whatever that was accomplished in that branch when browsing the master branch. My question now is, how can I accomplish this when working with a team? In that situation, the branches will be pushed to a remote repository, meaning that I can't squash all the commits in the branch down to a single commit. If the branch is public, can I still have a single useful merge commit in the master branch? (By "useful" I mean that the commit in the master line tells me (1) a useful summary of what was done in the branch and (2) diffs of the same.)

  Read the article

• JCP.Next Progress Updates

  - by heathervc

  JSR 355, JCP Executive Committee Merge, is currently nearing the end of the Public Review period.  Review the current draft here and provide feedback here.  The review closes on 12 June 2012.  The JCP Executive Committee met face to face in Sao Paulo, Brazil earlier in May, and has published a revision (version 2.1) of the EC Standing Rules.  The EC Standing Rules were introduced in October 2011 with the launch of JCP version 2.8 (JSR 348).  Version 2.1 of the EC Standing Rules will modify rules for attendance at EC face-to-face meetings. Remote observers will be permitted in "read-only" mode but unless a member attends in person they will be counted as absent.  The review period for these changes will close on June 30 2012.  Please comment on the proposed changes by logging an issue in the JCP EC issue tracker.

  Read the article

• Keyboard shorcut for a custom folder in Desktop

  - by palerdot

  I would like to configure a keyboard shortcut for a particular folder in my Desktop. I will be using this folder quite often and is there a way to open them with a custom keyboard shortcut ? The remote thing I came across regarding this is this question which is for opening home folder similar to Windows, but I do not want to go to home folder and navigate from there all the way to a folder in the Desktop (mouse clicking the desktop folder is way too easier than this method). So my Question: Can I have custom keyboard shortcuts for custom folders like folders in Desktop ? I'm using 12.04.

  Read the article

• How to modify grub entry for supporting KGDB kernel image?

  - by Nishant

  I am trying to update target m/c grub.cfg file for KGDB setup but while booting the m/c it got hung completely and not asking/waiting for remote gdb connection. Following is the entry which I added:- menuentry 'Ubuntu, with Linux 2.6.32-24-kgdb' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set 12878c3b-c553-4b4b-986a-6e32daea3ad1 linux /vmlinuz-2.6.32-kgdb root=/dev/mapper/ubuntu-root ro kgdbwait [email protected]/,@192.168.140.158/ quiet initrd /initrd.img-2.6.32-24-server } I have also compiled and copied /boot/vmlinuz-2.6.15.5-kgdb & /boot/System.map-2.6.15.5-kgdb to target m/c from devlopement m/c. STD entry before adding KGDB in grub.cfg was:- menuentry 'Ubuntu, with Linux 2.6.32-24-server' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set 12878c3b-c553-4b4b-986a-6e32daea3ad1 linux /vmlinuz-2.6.32-24-server root=/dev/mapper/ubuntu-root ro quiet initrd /initrd.img-2.6.32-24-server } Please suggest how to get rid of this problem.

  Read the article

• Some applications (Anki, Okular, Calibre) start very slowly

  - by k1U

  When I start one of the applications mentioned in the title from the terminal, I get this: Registered DEC: true Error in contacting registry "org.freedesktop.DBus.Error.NoReply" "Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken." Could not query active accessibility event listeners. Registered event listener change listener: true Currently I am running 12.04 This problem started a couple of days ago, shortly after I've installed okular from within the software center. by "slow" I mean it takes about 30 seconds. Other applications like chromium start instantly.

  Read the article

• Multicasting and VMWare

  - by John Breakwell

  Cracked a Multicasting problem this evening for one of my Canadian Tweeple. They wanted to mulitcast some MSMQ messages to another machine but nothing was arriving in the listening queue. A local queue could be configured to listen to the particular IP address/port in use and messages would arrive, though. Looking at the network traffic, nothing was going onto the wire for the IP address/port pair until they looked at traffic to the VMWare adapter. The machine had a virtual machine to simulate a remote computer and when they changed the setup from NAT to Bridge, multicasting burst into life.

  Read the article

• Advice on how to understand in general and in practice IT Infrastructure

  - by Luca

  My IT knowledge resides mainly in SW development. I have just some basic know how about networks. On the net I tried to get information and read books in order to better understand the overall IT infrastrcuture, but all the sources I found are too generic or, mainly, too detailed in just one aspect, making me lost. Could anyone suggest some books or web resources as good compromise in details? My goal would be able to understand the network issues and security threats when, for example, two remote system have to be setup and put in connection each other. Considering this scenario there are several aspects to consider: firewalls, intranet/internet interconnections, certificates for httpS, etc. The argument is quite wide, therefore I was looking for something that might help to start to understand this subject without going too deep in details (Computer Networks from A.Tanenbaum is a wonderful milestone, but way too specific for my scope). Thanks

  Read the article

• What set of tools make up "the rails way" of testing javascript in the browser?

  - by Jordan Feldstein

  What's the concensus for doing in-browser (either headless or remote-controlled) testing of javascript? Unit testing my JS is nice, but can't protect against irresponsible changes to the DOM. Unit testing of the JS and functional testing of the views to make sure they both provide and utilize the same, correct DOM, might work, but then the link between JS and DOM is being covered in two places which seems brittle or cumbersome. Is there an acknowledged "Rails Way" to implement full-stack tests, where I can run my javascript against the DOM rendered by the rest of the app, and check the results? (Something like what PHPUnit and Selenium give us, but inside the rails framework?)

  Read the article

• How to set up a mail server on Linux only for sending admin/debug emails?

  - by ChocoDeveloper

  I need to send server reports to myself from my remote servers, and I don't mind them going to spam, so I don't need SPF, DKIM, etc. I tried using mailutils to send something like this: uptime | mail -s "uptime" [email protected], but the emails don't go through. In /var/mail/root I received a message saying the HELO was invalid. So then I tried also adding -r root@my-ip, and now I don't get any error messages but I don't receive the email either. How can I do this?

  Read the article

• Error : Could not display "obex://" when paired with a Nokia 3110c

  - by MobileDev123

  Hi, I have paired my nokia 3110c via bt on my pc, I can receive a file from my pc to the phone, but I can not browse the contents of phone from my computer. Here is the error message Error: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. Please select another viewer and try again. How can I transfer contents from my phone to my computer?

  Read the article

• New Oracle Cloud support in OEPE

  - by gstachni

  Oracle Enterprise Pack for Eclipse 12c (12.1.1.1.1) includes updated support for development with the Java Cloud Service. Users can now do iterative development against their Java Cloud Service instance in addition to testing against local and remote WebLogic Server installations. Some details of the cloud tools are below: Templates and wizards to create projects and server configurations for Oracle Java Cloud Service Develop applications to run and deploy to the cloud, including Oracle ADF. Check cloud server runtime and deployment logs in new log analyzers Test applications before deployment with integrated whitelist scans. Whitelist tools support as-you-type validation, project build validation, and on demand scans to highlight coding violations. Errors are reported in application source, the Problems view, and a new Whitelist violations view. Access the Oracle Public Cloud administrative consoles directly from within Eclipse.

  Read the article

• Setting up a GUI-based libvirt VM

  - by LibertasMens

  I am attempting to create a virtual machine using libvirt that will have a GNOME GUI and remote accessibility. I have successfully set up the VM to run, but I am unable to access it remotely. The command issued to build the VM: sudo vmbuilder kvm ubuntu --suite=precise --flavour=generic --arch=amd64 --mirror=http://de.archive.ubuntu.com/ubuntu -o --libvirt=qemu:///system --part=/usr/xxxx/vmbuilder.partition --templates=/usr/xxxx/mytemplates --addpkg=nano --addpkg=unattended-upgrades --addpkg=acpid --firstboot=/usr/xxxx/boot.sh --cpus=2 --mem=4096--user=xxxx --name=xxxx --pass=xxxx --hostname=xxxx --bridge=br0 My intent is to have a virtual machine that my client can remotely access with a GUI.

  Read the article

• DesktopCouch does not sync

  - by burli

  I have here two computers, both installed with Ubuntu 10.10. The Laptop uses the Netbook Edition. Both are connected, file sync and Tomboy Notes are working. My Desktop syncs databases with Ubuntu One, my Laptop does not. If I delete for example the contacts Database on my Desktop, the database is back a view seconds later. If I delete the same database on my laptop, nothing happens. (I'm using Futon) If I kill beam, delete the config and try to restart with the dbus-send I got an error Error org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. How can I fix that?

  Read the article

• Redirect public traffic to a different subfolder, while local traffic remains unchanged

  - by ecnepsnai

  I would like to have local (intranet) HTTP traffic go to the /var/www/html folder while any public traffic goes to the subfolder, /var/www/html/public I've tried this configuration, with some variation, in httpd.conf <VirtualHost PRIVATE-IP> DocumentRoot /var/www/html ServerName ecn ErrorLog /var/www/logs/error/private CustomLog /var/www/logs/access/private common </VirtualHost> <VirtualHost PUBLIC-IP> DocumentRoot /var/www/html/public ServerName PUBLIC-DOMAIN-NAME ErrorLog /var/www/logs/error/public CustomLog /var/www/logs/access/public common </VirtualHost> PUBLIC-IP, PRIVATE-IP, and PUBLIC-DOMAIN name are all replaced with the correct values in the actual document. The problem is, local traffic can browse fine but remote traffic is directed to the root folder and getting 403d (because I have that folder blocked off through my .htaccess file). If I append /public to the URL it works fine.

  Read the article

• Regulating outgoing traffic on ubuntu VM

  - by DazSlayer

  I am making a virtual network setup for my high school cybersecurity team to practice. I am connecting all the VMs together through a VPN and then people who are practicing will VPN in and ssh/remote desktop into the different VMs. The problem is that for practicing, they will need root access into the VMs and because the VMs are connecting to my personal network, the VMs pose a security risk to my personal network. Is there any way in either VMWare or VirtualBox or even making an unchangeable iptable (I can make all the windows VMs go thru a linux VM) to prevent people from connecting to my local network via the VM?

  Read the article

• "Google files": Building a web interface to find/ack/grep

  - by user27915816

  I am working on a project where we would like to have build a web interface that gives the user the ability to "Google" files in a directory in a remote machine. For example, the user would type a string in a box, and then the system would find all files that contain that string and present them in the browser. The system would then give the user the ability click on any of the files to open them/display them in the browser. We want to avoid reinventing the wheel if possible, but don't really know where to start (none of us in the team have much experience building websites). What software packages, libraries or tools exist that can help us get this done?

  Read the article

• LINQ to Twitter Maintenance Feedback

  - by Joe Mayo

  Originally posted on: http://geekswithblogs.net/WinAZ/archive/2013/06/16/linq-to-twitter-maintenance-feedback.aspxIt’s always fun to receive positive feedback on your work. If you receive a sufficient amount of positive feedback, you know you’re doing something right. Sometimes, people provide negative feedback too. There are a couple ways to handle it: come back fighting or engage for clarification. The way you handle the negative feedback depends on what your goals are. Feedback Approaches If you know the feedback is incorrect and you need to promote your idea or product, you might want to come back fighting. The feedback might just be comments by a troll or competitor wanting to spread FUD. However, this could be the totally wrong approach if you misjudge the source and intentions of the feedback. In a lot of cases, feedback is a golden opportunity. Sometimes, a problem exists that you either don’t know about or don’t realize the true impact of the problem. If you decide to come back fighting, you might loose the opportunity to learn something new. However, if you engage the person providing the feedback, looking for clarification, you might learn something very important. Negative feedback and it’s clarification can lead to the collection of useful and actionable data. In my case, something that prompted this blog post, I noticed someone who tweeted a negative comment about LINQ to Twitter. Normally, any less than stellar comments are usually from folks that need help – so I help if I can. This was different. I was like “Don’t use LINQ to Twitter”. This is an open source project, the comment didn’t come from a competing project, and  sounded more like an expression of frustration. So I engaged. Not only did the person respond, but I got some decent quality feedback. What’s also interesting is a couple other side conversations sprouted on the subject, which gave me more useful data. LINQ to Twitter Thread Actions Essentially, this particular issue centered around maintenance. There are actually several sub-issues at play here: dependencies, error handling, debugging, and visibility. I’ll describe each one and my interpretation. Dependencies Dependencies are where a library has references to other libraries. This means that when you build your application, you need DLLs for the entire dependency graph for your application. There are several potential problems with this that include more libraries for configuration management, potential versioning mismatches, and lack of cross-platform support. In the early days of LINQ to Twitter, I allowed developers to contribute and add dependencies, but it became very problematic (for reasons stated). It was like a ball and chain that kept me from moving forward. So, I refactored and pulled other open-source into my project to eliminate external dependencies. This lets me fix the code in my project without relying on someone else to upgrade or fix their DLL. The motivation for this was from early negative feedback that translated as important data and acted on it. Today, LINQ to Twitter has zero dependencies. Note: Rejecting good code from community members who worked hard to make your project better is a painful experience in itself. I have to point out that any contribution was not in vain because they had a positive influence on my subsequent refactoring that resulted in a better developer experience. Error Handling Error handling has been a problem in the past. I have this combination of supporting both synchronous and asynchronous (APM) processing that can be complex at times. Within the last 6 months, I did a fair amount of refactoring to detect errors and process them properly. I also refactored TwitterQueryException so it includes important data from Twitter. During this refactoring, I’ve made breaking changes that I felt would improve the development experience (small things like renaming a callback property to Exception, rather than Error). I think the async error handling is much better than it was a year ago. For all the work I’ve done, there is more to do. I think that a combination of more error handling support, e.g. improving semantics, and education through documentation and samples will improve the error handling story. Because of what I’ve done so far, it isn’t bad, but I see opportunities for improvement. Debugging Debugging can be painful. Here’s why: you have multiple layers of technology to navigate and figure out where the real problem is – Twitter API, Security, HTTP, LINQ to Twitter, and application. You can probably add your own nuances to that list, but the point is that debugging in this environment can be complex. I think that my plans for error handling will contribute to making the debugging process easier. However, there’s more I can do in the way of documentation and guidance. Some of the questions to be answered revolve around when something goes wrong, how does the developer figure out that there is a problem, what the problem is, and what to do about it. One example that has gone a long way to helping LINQ to Twitter developers is the 401 FAQ. A 401 Unauthorized is the error that the Twitter API returns when a use isn’t able to authenticate and is one of the most difficult problems faced by LINQ to Twitter developers. What I did was read guidance from Twitter and collect techniques from my own development and actions helping other developers to compile an extensive list of reasons for the 401 and ways to fix the problem. At one time, over half of the questions I answered in the forums were to help solve 401 issues. After publishing the 401 FAQ, I rarely get a 401 question and it’s because the person didn’t know about the FAQ. If the person is too lazy to read the FAQ, that’s not my issue, but the results in support issues have been dramatic. I think debugging can benefit from the education and documentation approach, but I’m always open to suggestions on whatever else I can do. Visibility Visibility is a nuance of the error handling/debugging discussion but is deeply rooted in comfort and control. The questions to ask in this area are what is happening as my code runs and how testable is the code. In support of these areas, LINQ to Twitter does have logging and TwitterContext properties that help see what’s happening on requests. The logging functionality allows any developer to connect a TextWriter to the Log property of TwitterContext to see what’s happening. Further, TwitterContext has a Headers property to see the headers Twitter returns and a RawResults property to show the Json string Twitter returns. From a testing perspective, I’ve been able to write hundreds of unit tests, over 600 when this post is published, and growing. If you write your own library, you have full control over all of these aspects. The tradeoff here is that while you have access to the LINQ to Twitter source code and modify it for all the visibility, LINQ to Twitter *will* change (which is good) and you will have to figure out how to merge that with your changes (which is hard). The fact is that this is a limitation of any 3rd party library, not just LINQ to Twitter. So, it’s a design decision where the tradeoff is between control and productivity. That said, there are things I can do with LINQ to Twitter to make the visibility story more compelling. I think there are opportunities to improve diagnostics. This would be a ton of work because it would need to provide multi-level logging that can be tuned for production and support any logging provider you want to attach. I’ve considered approaches such as how the new Semantic Logging application block connects to Windows Error Reporting as a potential target. Whatever I do would need to be extensible without creating native external dependencies. e.g. how many 3rd party libraries force a dependency on a logging framework that you don’t use. So, this won’t be an easy feat, but I believe it can be part of the roadmap. I think that a lot of developers are unaware of existing visibility features, so the first step would be to provide more documentation and guidance. My thought are that this would lead to more feedback that will help improve this area. Summary Recent feedback highlights some of items that are important to LINQ to Twitter developers, such as dependencies, error handling, debugging, and visibility. I know that there are maintenance issues that have been problems for LINQ to Twitter developers in the past. I’ve done a lot of work in this area, such as improving error handling, adding visibility features, and providing extensive API documentation. That said, there is more to be done to make LINQ to Twitter the best Twitter API experience available for .NET developers and I welcome anyone’s thoughts on what I’ve written here or new improvements. @JoeMayo

  Read the article

• How to execute? [closed]

  - by Viswa

  Possible Duplicate: how to read the password from variable? I did the below code in my python script,but its not work. #! /usr/bin/python import os address = "rsync -avrz [email protected]:/opt/script/python/data/ /opt/script/python/data/" passwd ="my server password" os.system('%(address)s "echo %(passwd)s"' %locals()) it throws below error. If arg is a remote file/dir, prefix it with a colon (:). rsync error: syntax or usage error (code 1) at main.c(1236) [Receiver=3.0.7] If i run os.system('%(address)s' %locals()) means it work without any error but it ask password. I need that password should be read from my passwd variable. How to write python script to read server password from my variable.

  Read the article

• backup dedicated server runing ubuntu 10.04 and plesk 11.01 prior to update os to uduntu 12.04

  - by timmob

  i would like to backup my dedicated server which is my web server hosting various sites and email, so that I can update the os to Ubuntu 12.04, and basically restore back to 10.04 if things go wrong. I have a local machine that I can install 12.04 onto an then I was going to rsinc between the two, but I am fairly clueless when it comes to linux. I can ssh into the remote server and gain root access. can anyone explain if i need to backup the whole server hard drive or just some of the files? Thanks Timmo.

  Read the article

• When failure is a feature

  Warning: this post is going to be slightly off-topic and non-technical. Well, not computer science technical at least. I was reading an article in SciAm this morning about the possibility of a robot uprising. Dont laugh yet, this is a very real, if still quite remote possibility. The main idea that was described was that AI could rise one day to self-awareness and to an ability to improve itself through self-replication beyond human abilities to control it. Sure, thats one possibility, and some...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• bluetooth between ubuntu 10.10 and nokia error : Could not display "obex://"

  - by MobileDev123

  Hi, I have paired my nokia 3110c via bt on my pc, I can receive a file from my pc to the phone, but I can not browse the contents of phone from my computer. Here is the error message Error: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. Please select another viewer and try again. How can I transfer contents from my phone to my computer?

  Read the article

• Cloud consolidation handling multi databases

  - by llaszews

  I have spoken about virtualization and the different types of virtualization. Which includes OS zones, application server domains, database schemas, VLANS and other approaches. Another approach is to create a virtually federated database in the cloud. DBSpaces is a company that has a technology to created a virtually federated database in the cloud. DBSpaces is a Virtual Database technology that allows an organisation thru a single Virtual Database access multiple data sources (or database spaces) in real-time. Additionally dbSpaces can be configured to access an organisations data internally using a remote gateway so that their dbSpace is seamless across the Public and Private cloud.

  Read the article

• Chrome Mobile: The Mobile Web Developers Toolkit (Part 2)

  Chrome Mobile: The Mobile Web Developers Toolkit (Part 2) Building for mobile web requires a different mindset than desktop web development, and a different set of tools. The tools we're used to using often aren't available or would take up too much screen real estate. And going back to the dark ages of tweak/save/deploy/test/repeat isn't exactly optimal, so what can we do? Thankfully there are a number of great options - from remote debugging to emulation, mobile browsers are offering more and more tools to make our lives easier. We'll take a look at a couple of tools that you can use today to make cross platform mobile web development easier and then peer into the crystal ball to see what tools may bring in the future. Join us for Part 2 - as we take a look at a some of the many tools to make testing the mobile web easier. From: GoogleDevelopers Views: 0 0 ratings Time: 01:00:00 More in Science & Technology

  Read the article

< Previous Page | 520 521 522 523 524 525 526 527 528 529 530 531  | Next Page >