Search Results

Search found 18677 results on 748 pages for 'current'.

Page 525/748 | < Previous Page | 521 522 523 524 525 526 527 528 529 530 531 532  | Next Page >

• Proper Network Infastructure Setup DMZ, VPN, Routing Hardware Question

  - by NickToyota

  Greetings Server Fault Universe, So here's a quick background. Two weeks ago I started a new position as the systems administrator for an expanding health services company of just over 100 persons. The individual I was replacing left the company with little to no notice. Basically, I have inherited a network of one main HQ (where I am situated) which has existed for over 10 years, with five smaller offices (less than 20 persons). I am trying to make sense of the current setup. The network at the HQ includes: Linksys RV082 Router providing internet access for employees and site to site VPN connecting the smaller offices (using an RV042 each). We have both cable and dsl lines connected to balance traffic (however this does not work at all and is not my main concern right now). Cisco Ironport appliance. This is the main gateway for our incoming and outgoing emails. This also has an external IP and internal IP. Lotus domino in and out email servers connected to the mentioned Cisco gateway. These also have an external IP and internal IP. Two windows 2003 and 2008 boxes running as domain controllers with DNS of course. These also have both an external IP and internal IP. Website and web mail servers also on both external and internal IPs. I am still confused as why there are so many servers connected directly to the internet. I am seriously looking to redesign this setup with proper security practices in mind (my highest concern) and am in need of a proper firewall setup for the external/internal servers along with a VPN solution about 50 employees. Budget is not a concern as I have been given some flexibility to purchase necessary solutions. I have been told Cisco ASA appliance may help. Does anyone out in the Server Fault Universe have some recommendations? Thank you all in advance.

  Read the article

• Uninstall IIS on Windows 7

  - by CJM

  I've just rebuilt my development machine and installed IIS. I then installed the Web Deployment tool and used this to restore my previously-backed-up websites to the clean machine. Unfortunately the restoration didn't work correctly/fully. I couldn't easily correct the problem, so I decided to uninstall/reinstall IIS and recreate the sites manually. I uninstalled IIS and rebooted, but there was still plenty of stuff left around such as various files in /windows/system32/inetsrv/ which I tried to delete manually (with limited success!). I rebooted again and tried to reinstall IIS - it reported an error (no meaningful message) and requested another reboot. The event log includes the following errors: The World Wide Web Publishing Service (WWW Service) did not register the URL prefix http://*:80/gallery for site 1. The site has been disabled. and Unable to bind to the underlying transport for [::]:80. The IP Listen-Only list may contain a reference to an interface which may not exist on this machine. I'd like to avoid another rebuild. Can I completely remove IIS, such that I can reinstall it from scratch? Or can I 'fix' the current setup so that IIS will reinstall over what is already there?

  Read the article

• Physical-to-virtual for personal use

  - by Journeyman Geek

  One of my current projects involves reducing the number of old computers lying around. So far, the office systems have been downsized from 5 to 2. One system which had no data on it was dumped entirely, while three other identical boxes were consolidated into to one (I swap hard drives as needed and they just work(tm)). I want to make further cuts. The physical systems in question all run windows xp sp3, and were old Pentium 4s with 256 MB of RAM. Currently, I have got a VirtualBox running on another system. My intention is to migrate all services to that. We can assume that disk space and RAM on the host is not an issue. I'd rather not go with a client-server physical-to-virtual (P2V) method like what VirtualBox uses now. I have a few specific concerns as well - specifically whether I'd need to reactivate or sysprep for dissimilar hardware first. An offline tool for imaging (Windows or Linux) would not be an issue since the drives could be mounted onto another system I have anyway or I could use a LiveCD. What would be my options for P2V conversion, and what would I need to keep in mind when doing this?

  Read the article

• uWSGI cannot find "application" using Flask and Virtualenv

  - by skyler

  Using uWSGI to serve a simple wsgi app, (a simple "Hello, World") my configuration works, but when I try to run a Flask app, I get this in uWSGI's error logs: current working directory: /opt/python-env/coefficient/lib/python2.6/site-packages writing pidfile to /var/run/uwsgi.pid detected binary path: /opt/uwsgi/uwsgi setuid() to 497 your memory page size is 4096 bytes detected max file descriptor number: 1024 lock engine: pthread robust mutexes uwsgi socket 0 bound to TCP address 127.0.0.1:3031 fd 3 Python version: 2.6.6 (r266:84292, Jun 18 2012, 14:18:47) [GCC 4.4.6 20110731 (Red Hat 4.4.6-3)] Set PythonHome to /opt/python-env/coefficient/ *** Python threads support is disabled. You can enable it with --enable-threads *** Python main interpreter initialized at 0xbed3b0 your server socket listen backlog is limited to 100 connections *** Operational MODE: single process *** added /opt/python-env/coefficient/lib/python2.6/site-packages/ to pythonpath. unable to find "application" callable in file /var/www/coefficient/flask.py unable to load app 0 (mountpoint='') (callable not found or import error) *** no app loaded. going in full dynamic mode *** *** uWSGI is running in multiple interpreter mode ***` Note in particular this part of the log: unable to find "application" callable in file /var/www/coefficient/flask.py unable to load app 0 (mountpoint='') (callable not found or import error) **no app loaded. going in full dynamic mode** This is my Flask app: from flask import Flask app = Flask(__name__) @app.route("/") def hello(): return "Hello, World, from Flask!" Before I added my Virtualenv's pythonpath to my configuration file, I was getting an ImportError for Flask. I solved this though, I believe (I'm not receiving errors about it anymore) and here is my complete configuration file: uwsgi: #socket: /tmp/uwsgi.sock socket: 127.0.0.1:3031 daemonize: /var/log/uwsgi.log pidfile: /var/run/uwsgi.pid master: true vacuum: true #wsgi-file: /var/www/coefficient/coefficient.py wsgi-file: /var/www/coefficient/flask.py processes: 1 virtualenv: /opt/python-env/coefficient/ pythonpath: /opt/python-env/coefficient/lib/python2.6/site-packages This is how I start uWSGI, from an rc script: /opt/uwsgi/uwsgi --yaml /etc/uwsgi/conf.yaml --uid uwsgi And if I try to view the Flask program in a browser, I get this: **uWSGI Error** Python application not found Any help is appreciated.

  Read the article

• Drobo FS vs Lime Technology unRAID vs FreeNAS

  - by elluca

  I already decided to by a drobo fs until I just found these two tests: http://www.digitalversus.com/data-robotics-drobo-fs-p889_9543_487.html http://www.digitalversus.com/lime-technology-unraid-p889_8992_473.html The two cons agains drobo for me: loudness price What disadvantages has the unraid stuff against the drobo fs? Has it also got that ease of use like swapping drives on the go, simply extend capacity by plugging in new drives, notify me of drive errors, disk failure protection, dynamic space of "partitions", better/worse effective capacity, etc. Which is more secure? Am I able to simply replace a bad drive with a new one on unraid? What happens if my pc fails? Lets say the cpu overheats. Since I have a complete pc which is going to be replaced, I only have to pay the software to use unraid. I am going to use my nas for: music library (how well does it integrate with iTunes? ) picture library movie library development (i need to be able to be to use time machine) I am going to use this nas with a MacBook pro. My current disks: 2x 500Gb 1x 1.5Tb 1x 2Tb On a drobo fs I would have 2.26 Tb of space. What would it be on unraid? Is FreeNAS also an alternative?

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

• How do I handle a request for "index.php/somepath" in Nginx config?

  - by Arne

  I'm currently attempting to serve Icinga from nginx. The new Icinga-Web ui attempts to load a file from URL http://SERVER/icinga-web/index.php/appkit/squishloader/javascript (leading to a 404). How do I setup a location for this scenario? How do I get nginx to serve index.php and pass the full request path in a way Icinga understands? This is my current nginx config for icinga (adapted from the default apache config): server { server_name SERVER; root /opt/icinga/icinga-1.2.1; location /icinga-web/js/ext3 { alias /opt/icinga/icinga-1.2.1/lib/ext3; } location /icinga-web { alias /opt/icinga/icinga-1.2.1/pub; } location /icinga/cgi-bin { alias /opt/icinga/icinga-1.2.1/sbin; } location /icinga { alias /opt/icinga/icinga-1.2.1/share; } location ~ \.php([\?/].*)?$ { include fastcgi_params; fastcgi_pass 127.0.0.1:61000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } Any thoughts? Thanks!

  Read the article

• Driver issue for 7850 HD Diamond Windows 7

  - by Mr.Student

  I have an issue with windows 7 implementing the drivers ati provides for my 7850 HD Diamond video card. The video card is plugged in correctly to the PCIE 2.0 slots of my motherboard (p6t asus) with more then enough power. Fortunately the card works as I have my monitor plugged into the card itself and I can see just fine. However windows 7 does not replace the standard vga default microsoft driver with catalyst drivers that I've tried installing from online as well as the CD. Every time I install the drivers using Catalyst Install manager it always finishes with "Install complete(Warnings occured)". I then see the warnings it has which it instead reports that it successfully installed the SDK, Catalyst Install Manager, and HDMI/AUDIO packages. When I check my device manager after that, the display adapter still shows as standard vga and that its still using microsoft default display adapter. Now this current card is replacing an old card of mine which is the ATI 4890 HD which works beautifully. In fact for the old card to work, all I need to do is go to device manager and right click on standard vga - click update driver and windows 7 magically finds the correct driver to install and everything is good. Not so with the new card. I've even went into my regedits and uninstalled every bit of ati driver software before reinstalling my new card. Nothing's worked thus far. I've already exchanged my card out once and talked to customer support from my motherboard, microsoft, and ati all blaming the other. Please help me out!!

  Read the article

• ffmpeg - creating DNxHD MFX files with alphas

  - by Hugh

  Hi all, I'm struggling with something in FFMpeg at the moment... I'm trying to make DNxHD 1080p/24, 36Mb/s MXF files from a sequence of PNG files. My current command-line is: ffmpeg -y -f image2 -i /tmp/temp.%04d.png -s 1920x1080 -r 24 -vcodec dnxhd -f mxf -pix_fmt rgb32 -b 36Mb /tmp/temp.mxf To which ffmpeg gives me the output: Input #0, image2, from '/tmp/temp.%04d.png': Duration: 00:00:01.60, start: 0.000000, bitrate: N/A Stream #0.0: Video: png, rgb32, 1920x1080, 25 tbr, 25 tbn, 25 tbc Output #0, mxf, to '/tmp/temp.mxf': Stream #0.0: Video: dnxhd, yuv422p, 1920x1080, q=2-31, 36000 kb/s, 90k tbn, 24 tbc Stream mapping: Stream #0.0 -> #0.0 [mxf @ 0x1005800]unsupported video frame rate Could not write header for output file #0 (incorrect codec parameters ?) There are a few things in here that concern me: The output stream is insisting on being yuv422p, which doesn't support alpha. 24fps is an unsupported video frame rate? I've tried 23.976 too, and get the same thing. I then tried the same thing, but writing to a quicktime (still DNxHD, though) with: ffmpeg -y -f image2 -i /tmp/temp.%04d.png -s 1920x1080 -r 24 -vcodec dnxhd -f mov -pix_fmt rgb32 -b 36Mb /tmp/temp.mov This gives me the output: Input #0, image2, from '/tmp/1274263259.28098.%04d.png': Duration: 00:00:01.60, start: 0.000000, bitrate: N/A Stream #0.0: Video: png, rgb32, 1920x1080, 25 tbr, 25 tbn, 25 tbc Output #0, mov, to '/tmp/1274263259.28098.mov': Stream #0.0: Video: dnxhd, yuv422p, 1920x1080, q=2-31, 36000 kb/s, 90k tbn, 24 tbc Stream mapping: Stream #0.0 -> #0.0 Press [q] to stop encoding frame= 39 fps= 9 q=1.0 Lsize= 7177kB time=1.62 bitrate=36180.8kbits/s video:7176kB audio:0kB global headers:0kB muxing overhead 0.013636% Which obviously works, to a certain extent, but still has the issue of being yuv422p, and therefore losing the alpha. If I'm going to QuickTime, then I can get what I need using Shake, but my main aim here is to be able to generate .mxf files. Any thoughts? Thanks

  Read the article

• Script errors when run by launchd at startup, but not when run in Terminal

  - by Mechcozmo

  Hello. I'm attempting to create a RAM disk that loads the previous contents when the system starts up, and every six hours writes the contents to a disk image. Currently, when you run the script from the terminal ("sudo bash LogToRAM.sh") everything works fine. But when run from launchd during startup, it doesn't work. Here's the lines from the log; the first line just gives some idea as to where in the boot process we are: SecurityAgent[202] Showing Login Window com.mechcozmo.LogToRAM[51] + /Developer/usr/bin/SetFile -a V /Volumes/LogfileRAMdisk com.mechcozmo.LogToRAM[51] ERROR: File Not Found. (-43) on file: /Volumes/LogfileRAMdisk com.mechcozmo.LogToRAM[51] + /usr/sbin/asr -source '/Library/Application Support/LogToRAM/RAMdisk_store.dmg' -target /Volumes/LogfileRAMdisk/ -noverify Here is the script and plist file in question. Note that 'set -vx' is up at the top of the script; it give a lot of information about what is happening in the script. My current theory is that the /Volumes directory does not exist at this stage of the boot process, but that seems unlikely to be honest.

  Read the article

• NVidia Graphic Card troubleshooting

  - by Berry Langerak

  My dad has a HP pavilion laptop, which is over 6 years old. It contains an onboard graphic card, a NVidia GeForce 8400M GS. Since a week or two, he's getting BSOD in Windows Vista. Also, the screen was acting up; strange lines and figures keep creeping up, but only once in a while -- not always. Thinking that it might be the drivers he had recently upgraded, I decided to downgrade the driver, with no luck at all. I then continued to deinstall the driver, and reinstalling the current stable version, but alas, to no prevail. Windows kept crashing during the course of the last two weeks, and thinking it might be Windows breaking up, I decided to upgrade his Vista installation to Windows 7, as I've been hearing good things about it. Alas, even that didn't help, and it seems the strange lines and figures keep popping up. I've opened the laptop itself, thinking it might simply be overheating because of clogging in the vents, but that's not the case, it's clean as a whistle. Now for the actual question; does anyone have a decent flowchart on how to troubleshoot such issues? It might well be the videocard itself, as the strange lines and figures sometimes even appear during BIOS and POST, but I'm not sure.

  Read the article

• Windows installation repair option not showing up

  - by Jason

  I'm trying to repair an existing Windows XP installation. Following the instructions from http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/tips/doug92.mspx this should work: - 1.When the Press any key to boot from CD message is displayed on your screen, press a key to start your computer from the Windows XP CD. - 2.Press ENTER when you see the message To setup Windows XP now, and then press ENTER displayed on the Welcome to Setup screen. - 3.Do not choose the option to press R to use the Recovery Console. - 4.In the Windows XP Licensing Agreement, press F8 to agree to the license agreement. - 5.Make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP. - 6.Follow the instructions on the screen to complete Setup. On step 5 pressing R does nothing and there is nothing on the screen saying it would. When I just select to install I get a message that a previous installation is there and proceeding will destroy it and installed applications, I can optionally select a directory other than c:/windows, and I can optionally format before continuing. I had tried to go from SP2-SP3. It failed, and then I couldn't get to Safe Mode. I put the SP1 disk back in to do a repair, and I don't see that option. (I don't have an SP2 boot/install disk, I just have the non-boot upgrade package.)

  Read the article

• howto configure mod_proxy for apache2, jetty

  - by Kaustubh P

  Hello, This is how I have setup my environment, atm. An apache2 instance on port 80. Jetty instance on the same server, on port 8090. Use-Case: When I visit foo.com, I should see the webapp, which is hosted on jetty, port 8090. If I put foo.com/blog, I should see the wordpress blog, which is hosted on apache. (I read howtos on the web, and installed it using AMP.) Below are my various configuration files: /etc/apache2/mods-enabled/proxy.conf: ProxyPass / http://foo.com:8090/ << this is the jetty server ProxyPass /blog http://foo.com/blog ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPreserveHost On ProxyStatus On /etc/apache2/httpd.conf: LoadModule proxy_module /usr/lib/apache2/modules/mod_proxy.so LoadModule proxy_balancer_module /usr/lib/apache2/modules/mod_proxy_balancer.so LoadModule proxy_http_module /usr/lib/apache2/modules/mod_proxy_http.so LoadModule proxy_ajp_module /usr/lib/apache2/modules/mod_proxy_ajp.so I have not created any other files, in sites-available or sites-enabled. Current situation: If I goto foo.com, I see the webapp. If I goto foo.com/blog, I see a HTTP ERROR 404 Problem accessing /errors/404.html. Reason: NOT_FOUND powered by jetty:// If I comment out the first ProxyPass line, then on foo.com, I only see the homepage, without CSS applied, ie, only text.. .. and going to foo.com/blog gives me a this error: The proxy server received an invalid response from an upstream server. The proxy server could not handle the request GET /blog. Reason: Error reading from remote server I also cannot access /phpmyadmin, giving the same 404 NOT_FOUND error as above. I am running Debian squeeze on an Amazon EC2 Instance. Question: Where am I going wrong? What changes should I make in the proxy.conf (or another conf files) to be able to visit the blog?

  Read the article

• Excel not properly recalculating values

  - by gms8994

  I have an excel sheet with values in it (this sheet is generated by a custom perl script, but I don't think that's where the problem lies). In it, I have a formula: =sum(indirect(concatenate(address(6,column()),":",address(17,column())))) The purpose of this formula is to give me the SUM() of the cells in the current column, between rows 6 and 17. In Gnumeric Spreadsheet, as soon as I open the file, this works. But in Excel (both 2003 and 2007), opening the file gives #VALUE! errors in the fields with this formula, stating that the INDIRECT call with the values $B$6:$B$17 will result in an error. Here's the kink in the issue. If I edit the field (via F2), and make no changes, and hit enter, the values update. Also, it seems, if I save the file as .xlsx (Excel 2007 format), the values update upon opening. Unfortunately, I'm not sure that creating an xlsx is a possibility with the modules that I'm using, and many of our clients probably wouldn't be able to use it anyway. Any suggestions? Editing 200+ files every month for each client isn't going to be feasible, so if there's something I'm missing, please let me know.

  Read the article

• How to configure SCSI hard drives and RAID for Poweredge 2850 web server

  - by Saul

  I'm trying to set up a Poweredge 2850 as a web server, but as a server novice it's causing me some confusion. Its a virgin install so no data to be lost as yet, so I'd like to get the best arrangement for setting up Windows Server 2008. The box will run IIS, a mail and FTP server. The current physical arrangement of the hot swap drives is 1 73GB 3 146GB 5 blank 0 73GB 2 146GB 4 146GB (but flashes green, amber off) When I enter the PERC config screens on boot up I've got Raid Ch- 0 ID 0 ONLIN A00-00 1 ONLIN A00-01 2 ONLIN A01-00 3 ONLIN A01-01 4 HOTSP I think that drives 0 and 1 are set to RAID 1 and drives 2 and 3 are also set to RAID 1, certainly I can see 2 logical drives, both raid 1 of 69880MB and 139900MB Now what I think I am getting here is that the 2 73GB drives mirror each other and the 2 146GB drives mirror 2? so by my noob thinking if a drive fails I can pull it, insert and new one and it will reduplicate from its matching pair? I think the flashing amber probably indicates a failing drive in slot 4, should that just be binned? What confuses me coming from a home user XP background is that when I load up Windows Server 2008 OS under my computer I only see a C drive of about 70GB capacity. i.e wheres the 146GB drive? Any advice appreciated

  Read the article

• Apache2: How to split out the SSL configuration?

  - by Klaas van Schelven

  In Apache2, I'd like to separately define my SSL-related stuff once, and in a separate file from the rest of the configuration. This is mostly a matter of taste, but it also allows me to include the rest of the configuration in my automatic deployment process. I.e.: current situation: # in file: 0000-ourdomain.com.conf (number needs to be low) <VirtualHost xx.xx.xx.xx:443> # SSL part SSLEngine on SSLCertificateFile ....crt SSLCACertificateFile ...pem SSLCertificateChainFile ...intermediate.pem SSLCertificateKeyFile ....wildcard.ourdomain.com.key SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown ServerName www.ourdomain.com ServerAlias ourdomain.com # the actual configuration, as found for xx.xx.xx.xx:80, repeated </VirtualHost> I'd like # in file: 0000-ssl-stuff <VirtualHost xx.xx.xx.xx:443> # SSL part SSLEngine on SSLCertificateFile ....crt SSLCACertificateFile ...pem SSLCertificateChainFile ...intermediate.pem SSLCertificateKeyFile ....wildcard.ourdomain.com.key SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown ServerName www.ourdomain.com ServerAlias ourdomain.com </VirtualHost> # in file: ourdomain.com.conf <VirtualHost xx.xx.xx.xx:443> # the actual configuration, as found for xx.xx.xx.xx:80, repeated </VirtualHost> Unfortunately, this does not seem to work. Apache SSL fails, though it does not give an error message at reload or syntax-check. My best found workaround is to us an Include directive from the 0000-ssl file. Many thanks!

  Read the article

• Hard drive had reallocated sectors...but now it magically doesn't! Can I trust it?

  - by rob

  Last week my SMART diagnostics utility, CrystalDiskInfo, reported that the external hard drive that I was saving my backups to had suddenly reported 900+ reallocated sectors. I double-checked to confirm, then ordered a replacement drive. I spent all of this week copying data from that drive to the new drive. But toward the end of the copy, something peculiar happened. CrystalDiskInfo popped up an alert that the reallocated sector count had gone back down to 0. I know that when SMART detects a read error on a block, it adds that block to the current pending reallocation list. If it subsequently is successfully written or read later, it is removed from the list and assumed to be fine, but if a subsequent write fails, it is marked bad and added to the reallocated sector count. What concerns me most is that I've never read anywhere that a sector can be recovered as "good" after it has been marked as a bad sector and remapped. I've just finished running an extended SMART diagnostic, and it found no surface errors. Now I'm doubtful that the manufacturer will honor a warranty claim if the SMART info does not report any problems. Has anyone had this happen? If so, then is the drive, indeed, okay, or should I be concerned about an imminent failure?

  Read the article

• How to copy a bunch of pages? Is there a 3rd party tool?

  - by unknown (yahoo)

  (I asked the following question at the DNN forum, and also at snowcovered. Nobody knew of such an obvious time-saver being for sale. I'm posting here in case anybody knows of a freeware module that might do this.) By "groups of dnn pages", I mean pages that form a hierarchy (not necessary a hierarchy that is headed with a page at the same level as the Home page.) I know that I can copy web pages, one by one, using the admin login via the web-based dnn interface. But, I'd prefer a script or wizard, of some sort (that runs scripts behind the scenes) that can allow me to 1) specify a web page that I want to copy (along with the hierarchy of pages under it) 2) specify the names and titles of the new top-level pages 3) specify whether the contained modules of the top-level page that I want to copy is to be : ( ) New ( ) Copy ( ) Reference (as in the web-based interface) 4) repeat 3) for each of the source pages in the hierarchy that I want to copy You might say that I am looking to do something similar to creating a portal web site based on a template, except that it's not an entirely new website - instead it's a section of the current web site. I might want to do this because I have an organization which is broken into chapters, and I want each chapter to have, say, it's own General Information page (which acts like it's home page), and underneath that, in it's hierarchy, a Contact Info page and an Events page. so: Home Page   General Information Page     Contact Info     Events -- Home Page   General Information Page     Contact Info     Events   General Information Page Kiwanis - Bloomfield     Contact Info     Events   General Information Page Kiwanis - Dayton     Contact Info     Events If I have 200 chapters, I certainly don't want to copy those 3 web pages using the web based interface, as that would take a long time. (And imagine if each chapter's new sub-website had 30 pages!) I just want to specify the parameters of a copy process, then press a button, and let the system do the rest.

  Read the article

• VMWare Newbie - looking for hardware recommendations and help :) [closed]

  - by Dan

  I am looking for some hardware recommendations on an upcoming virtualization project. We are a small company (80 users - 25 in site 1, 55 in site 2) currently using Windows Server 2003 - no VM servers yet. Our AD is setup where site 1 is the root domain and site 2 is a subdomain/subnet - connected by T1 and VPN for failover. The current DC's also server as file servers, print servers, AntiVirus servers. Email is in the cloud. Additionally then in site 1 we have 3 additional member servers - one running IBM Websphere for a customer specific app, one running Infor PowerLink (no real heavy load) and another that we use for Virtual Studio apps and also runs DirSync for Exchange Online. No heavy workloads on any of these machines really. We also have an AS400 box that we run ERP/CRM software on that site 2 connects to over the WAN link. In site 2 we also have a SQL machine that runs on Win2K server. Database files are not large less than 5 GB. Light to Medium workload on this machine. File servers in each site store less than 500 GB data and probably won't grow to more than 1TB in the next 5 years. I am looking to go to VMWare in both sites and virtualize all servers. What recommendations do you have for server, storage hardware? Is it safe to virtualize all of your DC's? Any help or advice would be greatly appreciated. Thanks.

  Read the article

• IIS Windows Authentication not working in Internet Explorer via host name; works via IP

  - by jkohlhepp

  I'm trying to get a new Windows Server 2003 box working to host an ASP.NET application that uses Windows Authentication. Here's some info: IIS Anonymous Access is diabled IIS Integrated Windows Authentication is enabled I've tried it with and without Digest Authentication and it is the same result Both my machine and the server are in same active directory domain on the same intranet I'm using IE 6 My symptoms: In Firefox, via either IP or host name, a login box pops up, and if I enter my NT credentials, it works. In IE, via the server IP address, it works perfectly with no login box. In IE, via the server host name, it pops up a login box but even if I put in the correct credentials, it just pops up the box again. This is the problem. Why won't windows auth work in IE via host name but it will via IP address? Edit: Here's something else interesting. If I go into my Internet Explorer advanced settings and disable Windows Authentication, it seems to work just fine. And by work I mean that my test .NET app sees my NT ID as the current user.

  Read the article

• Adobe Reader Wants Sensitive Email Details

  - by KDM

  When I run Adobe Reader, it tells me: Either there is no default mail client or the current mail client cannot fulfill the messaging request. Please run Microsoft Outlook and set it as the default mail client. I have a couple of issues with this: 1) It presupposes everyone has Microsoft Office installed. Not all home users have the budget or inclination for this. 2) It presupposes everyone wants Microsoft Outlook to be their default mail client. 3) I have Microsoft Office (incl. Outlook) installed and set as my default mail client. Even if I make it the default mail client from within the Adobe Reader Preferences, that doesn't stop the dialog appearing. 4) I thought I'd give Adobe Reader a new email address in the preferences, just to get it to stop bugging me. I notice, though, that it want's the SMTP and POP addresses and the account password? They have got to be kidding? I just want to view PDF files. How do I get the message to go away without telling Adobe my life story, giving them my mother's maiden name, my favourite movie, my place of birth, the name of my first goldfish and emptying the contents of my wallet for them?

  Read the article

• is it good to have or difference between ADSL Modem+WiFi Router and Separate ADSL Modem & Wi-Fi Router?

  - by vikas devde

  I have ADSL2 Modem which I got from my service provider, now I want to setup wireless(Wi-Fi) in my home. I went to shop, where I came to know that there are routers which come up with modem also but they are priced lil higher than the only wi-fi routers. Now it is obvious that I should go for only wi-fi one, as I already have modem. My question is, is there any difference between ADSL+router and only router? I think if I use ADSL+router, the speed will increase lilbit, as modem does modulate and demodulate signals, and router also generates wireless signal, that is time to take conversions is doubled, and if I use ADSL+modem, it will directly convert the signals to wireless, and time will be saved, so the overall speed will increase lilbit. This is what my concept is(Which might be wrong). What do you guys would suggest me? should I take my current modem away and buy an ADSL+router or I should keep my modem and buy only wi-fi one. Please tell me the difference and suggest me which one I should go with, and also suggest me which company router I should go for.

  Read the article

• Upgrading openSUSE 11.1 with Plesk Panel 9.3 to PHP 5.3

  - by Jonathan Hogervorst

  Hello, I'm running a VPS with openSUSE 11.1 (i586). On the VPS is Parallels Plesk Panel 9.3.0 installed. The current PHP-version is PHP 5.2.11. I want to upgrade PHP to PHP 5.3, but I can't find good instructions on how to do this. If I check for updates in Zypper, it says this is the latest release. In the Plesk Updates isn't an update either, both via the webbased interface and the command line interface. On Software.openSUSE.org I can find packages for PHP 5.3.1 in both the server:php/server_apache_openSUSE_11.1-repo and the server:php/openSUSE_11.1-repo (can't post the link because I'm a newbie here). But if I add one of those to Zypper, I still don't see an update. Is there here somebody who knows how to do this? And is it completely safe to update that way? I don't want to end up with a broken VPS... Thanks! Jonathan

  Read the article

• VMWare Guest Info - Wrong IP Returned

  - by Jon Bailey

  We're running a VDI environment with vSphere 4.0 and Oracle VDI 3.2.2 and are having a bit of a problem with users that connect to an IPSec VPN from within their VM. For some reason, once connected to the VPN, the VMWare API returns GuestInfo.ipAddress as the VPN IP rather than the primary IP of the only NIC on the system. The IP address shown in net[0].ipAddress is the correct address and is what vSphere client is reporting. Is there any way to get VMWare tools to report the net[0].ipAddress as GuestInfo.ipAddress? Below is sample output from the guestinfo.pl script. 172.16.1.2 is the example "bad" VPN address that our VDI software is seeing. VMXFLEX01 guestFamily: windowsGuest VMXFLEX01 guestFullName: Microsoft Windows XP Professional (32-bit) VMXFLEX01 guestId: winXPProGuest VMXFLEX01 guestState: running VMXFLEX01 hostName: VMXFLEX01 VMXFLEX01 ipAddress: 172.16.1.2 VMXFLEX01 toolsStatus: VMware Tools is running and the version is current. VMXFLEX01 toolsVersion: 8194 VMXFLEX01 Screen - Height: 600 VMXFLEX01 Screen - Width: 800 VMXFLEX01 Disk[0]: Capacity 42935926784 VMXFLEX01 Disk[0]: Path : C:\ VMXFLEX01 Disk[0]: freespace : 33272619008 VMXFLEX01 net[0] - connected : 1 VMXFLEX01 net[0] - deviceConfigId : 4000 VMXFLEX01 net[0] - macAddress : 00:50:56:95:1f:c9 VMXFLEX01 net[0] - network : VM Network VMXFLEX01 net[0] - ipAddress : 10.0.0.2

  Read the article

• Can't make Dovecot communicate with Postfix using SASL (warning: SASL: Connect to private/auth failed: No such file or directory)

  - by Fred Rocha

  Solved. I will leave this as a reference to other people, as I have seen this error reported often enough on line. I had to change the path smtpd_sasl_path = private/auth in my /etc/postfix/main.cf to relative, instead of absolute. This is because in Debian Postfix runs chrooted (and how does this affect the path structure?! Anyone?) -- I am trying to get Dovecot to communicate with Postfix for SMTP support via SASL. the master plan is to be able to host multiple e-mail accounts on my (Debian Lenny 64 bits) server, using virtual users. Whenever I test my current configuration, by running telnet server-IP smtp I get the following error on mail.log warning: SASL: Connect to /var/spool/postfix/private/auth failed: No such file or directory Now, Dovecot is supposed to create the auth socket file, yet it doesn't. I have given the right privileges to the directory private, and even tried creating a auth file manually. The output of postconf -a is cyrus dovecot Am I correct in assuming from this that the package was compiled with SASL support? My dovecot.conf also holds client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } I have tried every solution out there, and am pretty much desperate after a full day of struggling with the issue. Can anybody help me, pretty please?

  Read the article

< Previous Page | 521 522 523 524 525 526 527 528 529 530 531 532  | Next Page >