Search Results

Search found 28989 results on 1160 pages for 'modal view controller'.

Page 529/1160 | < Previous Page | 525 526 527 528 529 530 531 532 533 534 535 536  | Next Page >

• Recovering data from failed Raid configuration with 4 drives and two raid sets (Asus P6T / Intel ICH10r)

  - by user56365

  I've added the complete detailed version for my question below for those who can help, but want to quickly summarize my question first. I setup two Raid arrays using (4) WD Raptors, a striped set for the OS and 1+0 set for crucial data. After booting once out of the 50 times a cable fell out, the drive wasn't recognized in the array anymore. After trying to fix it, another drive did the same. I now have two drives remaining, luckily with the parity information. I know the striped set is gone, but I need the data on the other set. Can anyone recommend anything to recover the data, or fix the two drives that doesn't allow the raid controller to recognize the drives, even though they are listed on the utility screen as still apart of the configuration but that they are not found? More Details I recently upgraded to a ASUS P6T motherboard with an Intel ICH10R raid controller and changed my previous 4 drive raid array from strictly a Raid 1+0 set to a Raid 0 for the OS/Page/Scratch drive and a Raid 1+0 set for crucial data. I never had problems after upgrading with my configuration, even when a drive died and was replaced. I managed to rebuild the array fine. Unfortunately this time around, a cable came unattached and I booted my system up until the raid status screen with the degraded error. This shouldn't have been a problem, but after I attached the drive it was no longer recognized as a member in the array. Both drives actually show up as a non-member disk. I've spent a very, very long time online trying to find information or support and haven't had much luck. After spending time trying to scan the drive for errors, damaged partition info, etc.. another drive in the set decided it didn't want to be recognized as a part of the array. At this point, I have two out of the four drives still functioning, but the Raid 1+0 array went from degraded to failed and I must find a way to retrieve that data. I think the two drives still in the array have the parity information because they show up as OS (110GB),BACKUP(80GB) and OS:1(110GB),BACKUP(80GB) under windows data management. The other two are simply 74gb Raw unallocated Is it possible recover the data using those two drive only, and which tool would I use? Could it be a simple partition table or any other error that is repairable with hard drive utilities out there? I know the Raid 0 set is done for, but I would assume because the correct drives failed in a 1+0 config to save the data I can retrieve it some how.

  Read the article

• Who should I run mysql as, on a personal computer?

  - by user664833

  I just installed mysql via homebrew (with brew install mysql, on Mac OS X Mountain Lion - recently installed from scratch). Following the installation, there is a "caveats" section with options around further necessary actions to take: ==> Caveats Set up databases to run AS YOUR USER ACCOUNT with: unset TMPDIR mysql_install_db --verbose --user=`whoami` --basedir="$(brew --prefix mysql)" --datadir=/usr/local/var/mysql --tmpdir=/tmp To set up base tables in another folder, or use a different user to run mysqld, view the help for mysqld_install_db: mysql_install_db --help and view the MySQL documentation: * http://dev.mysql.com/doc/refman/5.5/en/mysql-install-db.html * http://dev.mysql.com/doc/refman/5.5/en/default-privileges.html To run as, for instance, user "mysql", you may need to `sudo`: sudo mysql_install_db ...options... Start mysqld manually with: mysql.server start Note: if this fails, you probably forgot to run the first two steps up above A "/etc/my.cnf" from another install may interfere with a Homebrew-built server starting up correctly. To connect: mysql -uroot To launch on startup: * if this is your first install: mkdir -p ~/Library/LaunchAgents cp /usr/local/Cellar/mysql/5.5.27/homebrew.mxcl.mysql.plist ~/Library/LaunchAgents/ launchctl load -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist * if this is an upgrade and you already have the homebrew.mxcl.mysql.plist loaded: launchctl unload -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist cp /usr/local/Cellar/mysql/5.5.27/homebrew.mxcl.mysql.plist ~/Library/LaunchAgents/ launchctl load -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist You may also need to edit the plist to use the correct "UserName". On previous versions of Mac OS X I ran mysql as mysql user, but now I am confronted by the idea of running it as myself. I am the only one who uses this computer (which happens to be my laptop), and I do programming for work and for pleasure. What are the pros & cons, or best practices, around choosing whether to run mysql AS YOUR USER ACCOUNT or as mysql or something else still?

  Read the article

• Server resolve issues not consistent

  - by bobthemac

  I am having some weird issues with my web server. It has a public ip address and is set-up on an openVZ virtual machine. Accessing in to the site works fine every time but when trying to access out from the server I can't always connect out. Sometimes I can connect out and resolve addresses, sometimes I can't. The issue is visible in both ssh when trying to do a wget command on Google; sometimes it works and I get the index.html page and sometimes I get nothing. The issue is more visible in wordpress where you can't view themes but after a few presses of the try again button you can then view them. I have searched google and found nothing about this issue. Does anyone here have any ideas what could be causing this strange behaviour? Ports 80 and 2222 are open for web and ssh. Failed 17:26:33.398412 IP 86.148.184.124.38445 > 176.9.36.252.http: Flags [.], ack 98383, win 632, options [nop,nop,TS val 3070086 ecr 323106946], length 0 [email protected]..|. $..-.P..,.e......x....... .....B8. Passed 17:30:00.179630 IP 146.90.206.241.50091 > 176.9.36.252.http: Flags [F.], seq 1, ack 1, win 115, options [nop,nop,TS val 13740559 ecr 323308537], length 0 [email protected]... $....P.w...x.....s(K..... .....EK. Thanks in advance

  Read the article

• Windows 7 Startup Problems with Ethernet Driver

  - by c00lryguy

  Everytime I restart Windows 7, my Ethernet Driver can't connect: And I have to go into Device Manager - Network Adapters and disable then enable the Realtek PCIe GBE Family Controller to connect to the internet. And now, lately everytime I start up, I've been getting this error: Why do these happen when I start up Windows?

  Read the article

• Disable password complexity rule in Active Directory

  - by Dan Revell

  Where do I go to disable the password complexity policy for the domain. I've logged onto the domain controller (Windows Server 2008) and found the option in local policies which is of course locked from any changes. However I can't find the same sort of policies in the group policy manager. Which nodes do I have to expand out to find it?

  Read the article

• Time until Members added to Group Policy is Replicated

  - by Kyle Brandt

  If I have a group policy, and add a group/user/machine etc to that group policy, how long is it until all domain controllers have that change in effect? This is a Windows 2003 Domain set up with controllers at different geographic locations (Each with a different L3 network). I realize it probably depends, but how do I figure out how long it generally takes for my given setup? Also, is there an event I can check to see if it has a reached a particular domain controller?

  Read the article

• How to use AD/GPO/Print Services to "push out" a new printer driver to replace a broken one? How did my server get a broken driver?

  - by Zac B

  Context: We have an AD/GPO-managed corporate network with a little over a hundred PCs running Windows 7 x64, and a few managed printers. Our Server2008R2 primary domain controller is configured as a print server for them all. Problem: After a recent windows update and restart (no printer driver updates were included) on the DC, a particular shared printer (Lexmark T650) has begin exhibiting some strange behavior. First, it prints a preceding and following blank page for almost every document, on jobs submitted by about half of client machines (no separator page is configured on the server or any of the clients I've seen). Second, whenever someone tries to access "Printing Preferences" on any client, they recieve the following error message (this happens everywhere, 100% of the time, and didn't happen before the update on the DC): Once they click "OK", the prefs screen appears (with no separator page selected) and everything seems fine. I'm not even sure if these two issues are related, but everyone seems affected by one or both of those issues. What I've Tried: I've been hesitant to un-deploy the problem printer, or remove it via GPO, as it's pretty heavily used. I've tried updating (via MS update and our internal WSUS server) client machines and the DC. No printer driver updates have appeared, and no number of updates or restarts on the server or the client seems to have achieved anything other than my boss getting grumpy that I'm bouncing the domain controller so often. I've tried deleting the drivers on the server, and re-installing them from the original source that has worked for the past year...no change. I've tried selecting "New Driver" for one of the shared printers on a client machine, running as domain admin, and pushed the latest driver found by MSupdate back up to the DC. This changed the version number of the driver recorded in the print server manager, but caused no change--on the client I pushed from, or on any other. The error still appears. Question: Why the heck is this happening? Obviously, I got a bad driver from somewhere, but how do I get rid of it? I don't know of any "roll back drivers" functionality for centrally managed print drivers like Windows offers for other devices. How would I a) get this issue resolved on a client, and b) push the fix to the other members of the domain?

  Read the article

• PCIe network card deactivate DVI output (but NOT VGA output) on Shuttle SG41J1+

  - by wazoox

  It's all in the title :) Inserting a network card (or any other PCIe card, RAID controller, SAS, etc ) in the PCIe 16x slot of the Shuttle SG41J1 deactivate the DVI output. The VGA output still works fine. Shuttle support says that it's a chipset limitation (G41 + ICH7), but that doesn't make sense to me : the VGA and DVI share the same hardware but the D/A converter stage. Does anyone think that there may be some solution to this conundrum? Can a future BIOS update solve the problem?

  Read the article

• Roaming Profiles in 2008 server.

  - by Xiuhtecuhtli

  On my 2008 Domain Controller I have set a roaming profile path for my user. When i login, i get an info bubble saying that i am using a Temp Roaming profile. is this because of an issue with my profile path?

  Read the article

• Alternative method of viewing a database diagram in SQL Server to see what tables have gone missing?

  - by Triynko

  I have a database diagram for my database, but when I open it in SQL Server, I almost immediately get a message saying some permissions changed or tables in the diagram were dropped or renamed, and tables in the diagram vanish before I can even scroll over to see what or where they were. Basically, it's saying, "Hey, you know all that time you spent laying out tables in this diagram... half of them are going to vanish when you view it, and I'm not going to tell you which tables vanished or where they were in the diagram. You're just going to see a bunch of random empty spaces where tables used to be ;)" Ridiculous. So I thought that maybe if I look in the dbo.sysdiagrams table, I could look at some plain text definition of the diagram to get a clue about the names of the tables that went missing (because thier names were probably only changed slightly) or their coordinates in the diagram (because their spatial location would give me a clue as to what they were), so that I could re-add them, but I can't, because it's a binary definition. So, is there some other program I could use to view the existing database diagram that's not going to just drop and forget the missing tables without telling me what they were, or is this information lost and at the mercy of some SSMS-proprietary database diagram format and viewer which refuses to cooperate with me.

  Read the article

• Maximum number of hard drives in a build-your-own NAS solution [closed]

  - by groovehunter

  My IT department has a bunch of older 160/320GB Drives. I'd like to use them in a build-your-own NAS device. What limitations exist in regards to the maximum number of drives that can be connected to typical commodity hardware that might be used in a situation like this? EDIT okay I like to specify my question is what to search for to find a storage controller which can handle many drives. I simply cannot find the right search terms.

  Read the article

• Hardware imposed 32-bit limit

  - by knittl

  i'm thinking about converting my OS (ubuntu) to the 64 bit version to use the last bit of memory (4 gb)—ok, it's rather reinstalling … will this work as expected or are there possible limits given by the mainboard/memory controller/some other component, so i cannot fully utilize my full ram? if so, are there benefits from upgrading anyway?

  Read the article

• kerberos NTLM authentication

  - by rockbala

  Hi, Where can I check in Windows Server 2008 that Kereberos/NTLM is the authentication protocol used after the whole network is set up/installed. There is only 1 domain controller with AD services and is not affiliated with any other domains. Regards, Balaji S

  Read the article

• Hardware imposed 32-bit limit

  - by knittl

  i'm thinking about converting my OS (ubuntu) to the 64 bit version to use the last bit of memory (4 gb)—ok, it's rather reinstalling … will this work as expected or are there possible limits given by the mainboard/memory controller/some other component, so i cannot fully utilize my full ram? if so, are there benefits from upgrading anyway?

  Read the article

• gitweb refusing to blame

  - by Slipp D. Thompson

  I'm attempting to get gitweb (git 1.8.4.2, via git instaweb) in a project dir on my Debian server to offer blame views. In my /etc/gitweb.conf: … # default logo, favicon, etc. settings $feature{'blame'}{'default'} = [1]; $feature{'pickaxe'}{'default'} = [1]; $feature{'snapshot'}{'default'} = ['tgz', 'txz', 'zip']; $feature{'highlight'}{'default'} = [1]; $feature{'pathinfo'}{'default'} = [1]; In my global config file: [gitweb] blame = true snapshot = tgz, txz, zip patches = 256 avatar = gravatar [instaweb] local = false httpd = apache2 -f port = 4321 In my project's .git/config file: [gitweb] blame = true And yet, when I try to load a git blame view (via hand-modifying the URL to http://myserversip:4321/?p=.git;a=blame;f=Tests/InchCoordProxyTests.m;h=b4b2…;hb=53b4, since blame action links don't show up): Doing a quick search for “Blame view not allowed” in the gitweb.cgi source reveals plainly that the gitweb_check_feature('blame') conditional is failing. What am I doing wrong? Or, is there a way to verbosely print out why gitweb is doing what it's doing (e.g. which config files were read, which settings were loaded from each file, etc.)?

  Read the article

• Two Raid 1s in a single system?

  - by DebAtCQ

  I'm building a Raid array for the first time in my system and I have a question regarding having multiple Raid 1 arrays in a single Win 7 system. I'm a bit of an organizational freak with my data and I currently have two separate hard drives I want to mirror. The new motherboard I'm looking to buy supports Raid, so my question is this: a) can I have more than one Raid 1 array in a single system? b) would I have to buy a separate controller for the second array?

  Read the article

• Two Raid-1 arrays in a single system?

  - by DebAtCQ

  I'm building a Raid array for the first time in my system and I have a question regarding having multiple Raid-1 arrays in a single Win 7 system. I'm a bit of an organizational freak with my data and I currently have two separate hard drives I want to mirror. The new motherboard I'm looking to buy supports Raid, so my questions are: Can I have more than one Raid-1 array in a single system? Would I have to buy a separate controller for the second array?

  Read the article

• Does ZFS replace the need for hardware/software RAID?

  - by user53744

  I want to provide protection against data loss on my servers. Typically, I'd use hardware RAID 1 or 5, but I've been reading up on ZFS. Is it correct that ZFS itself provides RAID 1 or 5 like data protection WITHOUT needing a RAID controller card? If so, I assume a single hard drive is not enough to provide data protection since if that drive fails, all data fails, so how many hard drives do I need to be running for ZFS to provide this protection?

  Read the article

• USB Ports not working on new ASUS Z87 PRO motherboard

  - by Peter Coulton

  3 of the six USB ports on the back on my new ASUS Z87 PRO motherboard are not functioning properly. They do seem to deliver power, just don't seem to function for data (devices attached in these ports are detected by windows, or usable in UEFI) I think I'm right in saying that the top 4 ports (3 of which aren't working) run off an additional USB controller (not from the Z87 chipset) if that makes any difference. I'm pretty sure that I'll just have to return it, but any advice on diagnosing the problem would be welcome.

  Read the article

• How do I calculate the disk subsystem i/o capacity

  - by dbpinochle

  I am trying to figure out the number of 8K page i/o capacity for a disk subsystem. The drives are SATA 7200 RPM - 4 drives in a RAID-5 configuration. I am not sure about the SCSI controller but the server is about 5 years old.

  Read the article

• Domain joining an workstation question?

  - by ekamtaj

  Hey Guys, I have a question about domain joining workstations. We just upgraded exchange and AD to new server. I want to know how I domain join these old workstations to the new domain controller and preserve all the users document etc. Inother words I don't want to create another user account on the workstations. Thanks for all your help.

  Read the article

• Windows 8 RTM Final on Macbook Air

  - by Xarem

  If I try to install the Windows 8 RTM Final (from MSDN) on my Macbook Air Mid 2011 using Boot Camp, I get this error: Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu I already formatted the disk with NTFS, removed it, reformatted and more... Does anyone know to resolve this error? Thank you very much

  Read the article

• Workstation "joining" a domain

  - by ekamtaj

  I have a question about domain joining workstations. We just upgraded Exchange and AD to a new server. I want to know how I join these old workstations to the new domain controller and preserve all the users documents etc. In other words I don't want to create another user account on the workstations. Thanks for all your help.

  Read the article

• Constant crashes in windows 7 64bit when playing games

  - by yx.

  I've tried everything I can possibly think of in trying to fix this problem and I'm totally out of ideas, so any help would be appreciated: The problem: whenever I fire up a game, it works for a short while with no problems and then it would crash. Either its a hard crash, forcing me to reboot, or windows would report that the display driver has stopped working and recovered. Here is a list of things I've already tried: Drivers - tried the latest drivers (catalyst 9.12) as well as the stock drivers that came with the video card. Also have the latest BIOS/chipset Memtest - Ran Memtest86+ overnight, had no problems, the windows diagnostic tool also does not find any problems. Overheating - Video card/cpu temperatures are well below peak (42 and 31 Celsius receptively) PSU Voltage - CPUID shows that the voltage levels are all above what they should be. The PSU itself is only roughly 16 months old and is a good model. HDD - No errors when checked GPU - Brand new (replaced previous card since I thought it was the problem, apparently not) Overclocking - Everything is at stock levels, memory voltage is set to manufacturer's standard Specs: Motherboard: ASUS P5Q Pro CPU: Core 2 Duo E8400 3.0 ghz OS: Windows 7 home premium 64 bit Memory: Mushkin Enhanced 4GB DDR2 GPU: Sapphire HD 5850 1GB PSU: SeaSonic M12 600W ATX12V DirectX: DX11 Event Viewer after a crash always has these logged: A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 1 The details view of this entry contains further information. A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 0 The details view of this entry contains further information. A previous card that I had (4850x2) also had these errors, so I changed video cards, but the same thing is happening.

  Read the article

• Unexpected behaviour in a Lotus Notes programmable table

  - by Mark B

  I'm designing a workflow database in Lotus Notes 6.0.3 (soon upgrading to 8.5), and my OS is Windows XP. I have recently tried converting a tabbed table into a programmable one. This was so that I could control which tab was displayed to the user when it was opened, so that they were presented with the most appropriate one for that document's progress through the workflow. That part of it works! One of the tabs features a radio button that controls visibility of the next tab, and a pair of cascading dialogue boxes. One contains the static list "Person":"Team", and the other has a formula based on the first: view:=@If(PeerReview = "Team"; "GroupNames"; "GroupMembers"); @Unique(@DbColumn(""; ""; view; 1)) The dialogue boxes have the property "Refresh fields on keyword change" selected. The behaviour that I wasn't expecting is this. If the radio button is set to "Yes" and a value is selected in one of the dialogue boxes, the table opens the next tab. If the radio button is set to "No" and a value is selected in one of the dialogue boxes, the entire table is hidden. I can duplicate the latter by switching off the "Refresh fields on keyword change" property on the dialogue boxes and instead pressing F9 after selecting a value. I have no idea why the former occurs, though. The table is called "RFCInfo", and I have a field on the form called "$RFCInfo" which is editable, hidden from all users who aren't me and initially set by a Postopen script, which I can post if necessary - it's essentially a Select Case statement that looks at a particular item value and returns the name of the table row relating to that value. Can anyone offer any pointers?

  Read the article

< Previous Page | 525 526 527 528 529 530 531 532 533 534 535 536  | Next Page >