Search Results

Search found 21589 results on 864 pages for 'primary key'.

Page 539/864 | < Previous Page | 535 536 537 538 539 540 541 542 543 544 545 546  | Next Page >

  • How do I set up DNS with nic.io to point to an AWS EC2 server?

    - by Chad Johnson
    I purchased a domain one week ago via nic.io. I have elected to provide my own DNS [because they provided no other option]. I'm trying to point my .io domain at my EC2 server instance. I've allocated an elastic IP and associated it with the instance. I can SSH into the instance and access point 80 via the IP address just fine. The IP is 54.235.201.241. nic.io support said the following: "You have selected to provide your own DNS and therefore if there is an issue with the set-up of the name servers you will need to contact your DNS provider." So, I created a Hosted Zone via Route 53 in AWS. This created NS and SOA records. I then set the Primary and Secondary servers at nic.io's domain admin page to the SOA record domains. Additionally, I set the optional servers to the NS domains. I did this two days ago, and I can't access the server via the domain. I ran a DNS check here...still not sure what I need to do: http://mydnscheck.com/?domain=chadjohnson.io&ns1=&ns2=&ns3=&ns4=&ns5=&ns6=. I have no idea what I'm supposed to do. Does anyone have any ideas?

    Read the article

  • Zabbix Proxy not collecting data

    - by syntaxcollector
    Hi All I have a working Zabbix 1.8.2 server collecting data for our office and our colo facility. However the link between the colo and office is flaky. What I'm trying to do is setup a proxy on the colo side to have a 1 hour cache and relay the data to our primary server at the office. Our zabbix server is compiled from source and uses a mysql database I've followed the instructions found in the zabbix documentation to compile the proxy using a sqlite3 database. I add the proxy to zabbix under Administration-DM-Proxies. The zabbix server "sees" the proxy because the "last seen" field is always under 60s. However when I assign a colo host to the proxy I stop receiving data from it. The colo host's zabbix_agentd.log file says this: 29343:20100622:124847 Timeout while answering request 29343:20100622:124847 Getting list of active checks failed. Will retry after 60 seconds The zabbix_proxy.log says this. 2041:20100622:123131.760 Deleted 0 records from history [0.000994 seconds] 2028:20100622:124131.671 Error while receiving answer from server [ZBX_TCP_READ() failed I also am unable to receive any SNMP data which is more important to me than the zabbix agent data. Has anyone had this problem before? Zabbix Server OS: CentOS5.4 Zabbix Server Build: 1.8.2 from source Zabbix Proxy OS: CentOS5.4 Zabbix Proxy Build: 1.8.2 from source P.S. The SQLite database on the zabbix proxy never gets any data written to it, it is identical to when I created it from the blank schema in zabbix-1.8.2/create/schema. (Yes I've checked the permissions)

    Read the article

  • DNS Does Not Register at Off-site Locations

    - by Russ Warren
    First of all, let me give you the specifics of our setup: Windows Small Business Server 2008 Domain w/ all applicable updates on the DC The DC does DHCP for the main site The DC does DNS for all sites 3 sites including our headquarters where the DC is located All sites are connected through OpenVPN SSL tunnels terminated by an Untangle box at each site The 2 remote sites us the Untangle box as a DHCP server for their subnet, which assigns the DC as the primary DNS server Collection of Windows XP and Windows 7 workstations connected to the domain Here's the issue: All of the workstations at the main site register with the DNS server on the domain controller fine. As they grab an IP from the DHCP server, it updates the DNS server with the new host record. I have 2 systems (each at different remote sites) that fail to register with the DNS server. I've attempted the following troubleshooting steps: Confirmed the network adapter is using the DC as a DNS server Confirmed 2-way traffic is possible between DC and workstation Verified the "Register with DNS server" setting was checked in the adapter properties Attempted ipconfig /registerdns and received no errors For the time being, I have setup a DHCP reservation for these systems and manually created a host record. This seems to work fine, but I need a solution for any new systems that go out there.

    Read the article

  • Linux Mint 13 is not booting on dual boot computer

    - by Brian
    thanks in advance for your time. I have 2 hard drives in my computer a 300 GB drive which is my primary drive for windows 7 and a 1.5 TB drive that I'd used for storage. When I got it I partitioned 500 GB for use in Linux. So, I created a bootable USB and clicked the "Install by Current Operating System" option from Mint. It installed it to the free 500 GB like I'd hoped it would. Now, I can't get it to boot though. I've tried using EasyBCD to create the boot entry and it hangs on a black screen. Thanks. EDIT @ Ryhuk It presents a menu with two options 1) Windows and 2) Mint. This was a menu I created with easyBCD. When I select option 1 it boots to windows fine. When I select option 2 it hangs on a black screen with just a white bar flashing (Can't remember what its called, it marks the current cursor location on a text field) and won't respond to any key presses but alt ctrl del.

    Read the article

  • Freebsd Secondary Group not allowing folder deletion

    - by Jarrod Juleff
    TLDR: I have a user that is a member to a group as a secondary group. This user can delete files with 664 perms as a secondary user, but not directories with perms of 775. Details: I have a user. Lets call him ftpuser. I use him to upload and download files to my devbox. The user's primary group is "ftp" and is also in the group "www" as a secondary group. My web server runs as user www and group www, and I have proftpd (running as www and www) configured to drop all files into the needed directories as www and www (for file ownership) and perms 664 on files and 775 on directories. My problem is (tried with 2 ftp clients) the ftp client can delete the files, but not the folders. Filezilla returns 550 permission denied. The owner only can delete flag is not set, and I've triple checked the permissions and they are indeed 775. Its driving me nuts to have to log into my server to manually delete folders every time. Some of the folders and files are created by 1 of my php scripts, but the permissions are getting set properly when I check the files' properties. Directory and file creation works phenomenal. Can delete files, just not directories. Freebsd 9.0 Running in VirtualBox (32bit all the way around) Proftpd (running as www and www) as ftp server (tried using both dreamweaver and filezilla as the clients) Basic amp setup (apache,mysql,and php).

    Read the article

  • Windows 7 Multi-NIC woes

    - by Eric
    I have Comcast business Internet here. It gives me 5 static IPs. Most of the machines in my house connect to a router like every other household. It has a 192.168.117.x subnet, DHCP Server, etc. and all is well. However, I have a second machine on MY desk that has a life Internet IP. Up until yesterday, this machine was running XP Pro. The primary NIC was manually set to 192.168.117.241 with no gateway, and the secondary NIC was manually set to 173.x.x.171 with a gateway of 173.x.x.174. This worked just fine for years. Yesterday I replaced that XP machine with a brand new Windows 7 x64 box. Again, I configured it the same way. The onboard NIC was given a static 192.168.117.x address with no gateway, and the secondary NIC was given a live Internet IP address with the proper router, etc. 2 Problems. First is that the internal network (192.168.117.x) is listed as a public network because there's no gateway, so that means no homegroup, no file sharing, none of that. And I can't change it from what I'm reading... The second is that the machine reports the "router" ip address as it's address, and not the address that it's supposed to. I'm ready to tear my hair out over this. Any ideas?

    Read the article

  • Apache reverse proxy POST 403

    - by qkslvrwolf
    I am trying to get Jira and Stash to talk to each other via a Trusted Application link. The setup, currently, looks like this: Jira - http - Jira Proxy -https- stash proxy -http- stash. Jira and the Jira proxy are on the same machine. The Jira Proxy is showing 403 Forbidden for POST requests from the stash server. It works (or seems to ) for everything else. I contend that since we're seeing 403 forbiddens in the access log for apache, Jira is never seeing the request. Why is apache forbidding posts,and how do I fix it? Note that the IPs for both Stash and the Stash Proxy are in the "trusted host" section. My config: LogLevel info CustomLog "|/usr/sbin/rotatelogs /var/log/apache2/access.log 86400" common ServerSignature off ServerTokens prod Listen 8443 <VirtualHost *:443> ServerName jira.company.com SSLEngine on SSLOptions +StrictRequire SSLCertificateFile /etc/ssl/certs/server.cer SSLCertificateKeyFile /etc/ssl/private/server.key SSLProtocol +SSLv3 +TLSv1 SSLCipherSuite DHE-RSA-AES256-SHA:DHE-DSS-AES256-SHA:AES256-SHA:DHE-RSA-AES128-SHA:DHE-DSS-AES128-SHA:AES128-SHA:EDH-RSA-DES-CBC3-SHA:EDH-DSS-DES-CBC3-SHA:DES-CBC3-SHA # If context path is not "/wiki", then send to /jira. RedirectMatch 301 ^/$ https://jira.company.com/jira RedirectMatch 301 ^/gsd(.*)$ https://jira.company.com/jira$1 ProxyRequests On ProxyPreserveHost On ProxyVia On ProxyPass /jira http://localhost:8080/jira ProxyPassReverse /jira http://localhost:8080/jira <Proxy *> Order deny,allow Allow from all </Proxy> RewriteEngine on RewriteLog "/var/log/apache2/rewrite.log" RewriteLogLevel 2 # Disable TRACE/TRACK requests, per security. RewriteCond %{REQUEST_METHOD} ^(TRACE|TRACK) RewriteRule .* - [F] DocumentRoot /var/www DirectoryIndex index.html <Directory /var/www> Options FollowSymLinks AllowOverride None Order deny,allow Allow from all </Directory> <LocationMatch "/"> Order deny,allow Deny from all allow from x.x.71.8 allow from x.x.8.123 allow from x.x.120.179 allow from x.x.120.73 allow from x.x.120.45 satisfy any SetEnvif Remote_Addr "x.x.71.8" TRUSTED_HOST SetEnvif Remote_Addr "x.x.8.123" TRUSTED_HOST SetEnvif Remote_Addr "x.x.120.179" TRUSTED_HOST SetEnvif Remote_Addr "x.x.120.73" TRUSTED_HOST SetEnvif Remote_Addr "x.x.120.45" TRUSTED_HOST </LocationMatch> <LocationMatch ^> SSLRequireSSL AuthType CompanyNet PubcookieInactiveExpire -1 PubcookieAppID jira.company.com require valid-user RequestHeader set userid %{REMOTE_USER}s </LocationMatch> </VirtualHost> # Port open for SSL, non-pubcookie access. Used to access APIs with Basic Auth. <VirtualHost *:8443> SSLEngine on SSLOptions +StrictRequire SSLCertificateFile /etc/ssl/certs/server.cer SSLCertificateKeyFile /etc/ssl/private/server.key SSLProtocol +SSLv3 +TLSv1 SSLCipherSuite DHE-RSA-AES256-SHA:DHE-DSS-AES256-SHA:AES256-SHA:DHE-RSA-AES128-SHA:DHE-DSS-AES128-SHA:AES128-SHA:EDH-RSA-DES-CBC3-SHA:EDH-DSS-DES-CBC3-SHA:DES-CBC3-SHA ProxyRequests On ProxyPreserveHost On ProxyVia On ProxyPass /jira http://localhost:8080/jira ProxyPassReverse /jira http://localhost:8080/jira <Proxy *> Order deny,allow Allow from all </Proxy> RewriteEngine on RewriteLog "/var/log/apache2/rewrite.log" RewriteLogLevel 2 # Disable TRACE/TRACK requests, per security. RewriteCond %{REQUEST_METHOD} ^(TRACE|TRACK) RewriteRule .* - [F] DocumentRoot /var/www DirectoryIndex index.html <Directory /var/www> Options FollowSymLinks AllowOverride None Order deny,allow Allow from all </Directory> </VirtualHost> <VirtualHost jira.company.com:80> ServerName jira.company.com RedirectMatch 301 /(.*)$ https://jira.company.com/$1 RewriteEngine on RewriteCond %{REQUEST_METHOD} ^(TRACE|TRACK) RewriteRule .* - [F] </VirtualHost> <VirtualHost *:80> ServerName go.company.com RedirectMatch 301 /(.*)$ https://jira.company.com/$1 RewriteEngine on RewriteCond %{REQUEST_METHOD} ^(TRACE|TRACK) RewriteRule .* - [F] </VirtualHost>

    Read the article

  • Debian/OVH: How to configure multiple Failover IP on the same Xen (Debian) Virtual Machine?

    - by D.S.
    I have a problem on a Xen virtual machine (running latest Debian), when I try to configure a second failover IP address. OVH reports that my IP is misconfigured and they complaint they receive a massive quantity of ARP packets from this IPs, so they are going to block my IP unless I fix this issue. I suspect there's a routing issue, but I don't know (and can't find any useful info on the provider's website, and their support doesn't provide me a valid solution, just bounce me to their online - useless - guides). My /etc/network/interfaces look like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address AAA.AAA.AAA.AAA netmask 255.255.255.255 broadcast AAA.AAA.AAA.AAA post-up route add 000.000.000.254 dev eth0 post-up route add default default gw 000.000.000.254 dev eth0 # Secondary NIC auto eth0:0 iface eth0:0 inet static address BBB.BBB.BBB.BBB netmask 255.255.255.255 broadcast BBB.BBB.BBB.BBB And the routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 000.000.000.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 0.0.0.0 000.000.000.254 0.0.0.0 UG 0 0 0 eth0 In these examples (true IP addresses are replaced by fake ones, guess why :)), 000.000.000.000 is my main server's IP address (dom0), 000.000.000.254 is the default gateway OVH recommends, AAA.AAA.AAA.AAA is the first IP Failover and BBB.BBB.BBB.BBB is the second one. I need both AAA.AAA.AAA.AAA and BBB.BBB.BBB.BBB to be publicly reachable from Internet and point to my domU, and to be able to access Internet from inside the virtual machine (domU). I am using eth0 and eth0:0 because due to OVH support, I have to assign both IPs to the same MAC address and then create a virtual eth0:0 interface for the second IP. Any suggestion? What am I doing wrong? How can I stop OVH complaining about ARP flood? Many thanks in advance, DS

    Read the article

  • Ubuntu Server: Networking fails with MODPROBE option in /etc/network/interfaces ... ??

    - by neezer
    For some reason (which I haven't been able to determine yet), yesterday morning the networking service on our web server (running Ubuntu 8.04.2 LTS -- hardy) wouldn't start, and our website went down. I noticed the following error message when trying to restart it: * Reconfiguring network interfaces... /etc/network/interfaces:6: option with empty value ifup: couldn't read interfaces file "/etc/network/interfaces" ...fail! Line 6 in the /etc/network/interfaces file concerned a MODPROBE command, which (I believe) loaded in the ip_conntrack_ftp module so that I could use PASV on my FTP server (vsftpd): (breaking modprobe commands commented out below) # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. # The loopback network interface auto lo iface lo inet loopback #MODPROBE=/sbin/modprobe #$MODPROBE ip_conntrack_ftp pre-up iptables-restore < /etc/iptables.up.rules # The primary network interface # Uncomment this and configure after the system has booted for the first time auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask 255.255.255.0 gateway xxx.xxx.xxx.1 dns-nameservers xxx.xxx.xxx.4 xxx.xxx.xxx.5 I've verified that there is a file in /sbin called modprobe. Like I said earlier, this setup had been working flawlessly until yesterday morning (though my bosses say that the site actually went down the previous night at 11 PM EST). Can anyone shed some light on (A) why this broke, and (B) how can I re-enable the ip_conntrack_ftp module?

    Read the article

  • Running DNS locally for home network

    - by Roy Rico
    I have a small home network that just got larger ( New roommate, My existing roommate got a laptop (on top of her computer)j, my friends coming over with laptop, etc ). I'd like to run a local DNS server for lookups of my local network stuff (fileserver.local, windowsTV.local, machineA.local, machineB.local, appletv.local). I used to have a business line with a static IP, and run bind/named internally. However, now, I have a normal account. My ISP's DNS servers are constantly changing (for whatever reasons my ISP doesn't like to keep the same IP range for long). I need my local DNS to be automatically updated to use my ISP's DNS for external traffic, but be able to maintain an internal DNS server (getting to update the hosts file is being a hassle with every new machine on top of rebuilding existing machines with win7 or Ubuntu 9.04). Additionally, My ISP's DNS servers often crash or become unresponsive. Are there any open DNS servers that are reliable (i don't want to reconfig every day) that I could use as my primary, then if those fail, then use my ISP's? UPDATE: Also looking for each workstation to be able to use dhcp to connect, but instead of getting ISP dns servers, getting my internal one.... Thanks

    Read the article

  • Installation of Active Directory on separate VM from DNS does not entierly work - not sure why

    - by René Kåbis
    Not sure what I am doing wrong here. I have a moderately midrange server (16 cores, 2Ghz, 32GB ECC REG RAM, 6TB storage, nothing too extreme) where I am running Hyper-V (Server 2012 R2 Enterprise) in order to provision virtual machines. So why an AD separate from DNS? I want redundancy. I want to be able to move VMs and back them up individually and not have too many services on any one VM. I have already provisioned a VM with DNS, and have set it up right -- essentially, I have: Set up Static IP’s for everyone involved. Installed the DNS service on the DNS VM. Created a forward lookup zone and a reverse lookup zone (primary zone) xyz.ca Configured the zones to use nonsecure and secure dynamic updates (i will change this to secure later after the domain controller is online). Created a A record for the DC in the forward lookup zone (and a reverse ptr) Changed DC’s DNS server (network settings) to the new DNS server. Checked that I can ping the dns server from the new DC by hostname. When I went ahead and did a DCpromo on the DC, and un-cheked the “install DNS” option, everything seemed to go well (no error messages), but I saw no changes on the DNS server whatsoever (no additional settings). Plus, the DNS server seems to be unable to join the domain, as it claims that the domain is not discoverable. As a final note, I do run Symantec Endpoint Protection, which includes a firewall and most settings set as default. I have not yet tried turning this off, but my experience has been that if a service would open up a port on a Windows firewall, it would do the same through Symantec. There is pretty tight integration these days with corporate-class AV and Windows. I have a template vhdx fully set up (just short of any special roles and features) that I can use to replace the current AD VM with, so doing this all over again is not too much skin off of my nose.

    Read the article

  • Slow parity initialization of RAID-5 array on HP Smart Array 411 controller

    - by Rob Nicholson
    On 29th October 2011, I built a RAID-5 array using 4 x 146.8GB Seagate SAS ST3146855SS drives running at 15k connected to a PowerEdge R515 with HP Smart Array P411 controller running Windows 2008 (so nothing particularly unusual). I know that parity initialisation of a RAID-5 array can take some time but it's still running after 2.5 weeks which seems a little unusual. I'd previously built another array on the same controller using 4 x 2TB SATA-2 drives and that did take a while to complete but a) I'm sure it was less than 2.5 weeks, b) that array was ~12 times bigger and c) during initialization, the percentrage slowly increased each day. At the moment, the status display for this new 2nd array simply says "Parity Initialization Status: In Progress" and it's said that since the start. It's this lack of change on the status that worries me the most - feels like it's not actually doing anything. Do you think something has gone wrong or am I being unpatient and for some reason, the status not increasing is normal? I kind of expected a much smaller array on faster drives (15k SAS versus 7.5k SATA-2) to build in a few days. This is our primary SAN running StarWind so my "have a play" options are very limited. This 2nd array is currently in use for one small virtual disk so I could shut the target machine down, move the virtual disk to another drive and try rebuilding.

    Read the article

  • Exchange 2010 Mail Enabled Public Folder Unable to Recieve External (anon) e-mail.

    - by Alex
    Hello All, I am having issues with my "Public Folders" mail enabled folders receiving e-mails from external senders. The folder is setup with three Accepted Domains (names changed for privacy reasons): 1 - domain1.com (primary & Authoritative) 2 - domain2.com (Authoritative) 3 - domain3.com (Authoritative) When someone attempts to send an e-mail to [email protected] from inside the organization, the e-mail is received and placed in the appropriate folder. However, when someone tries to send an e-mail from outside the organization (such as a gmail account), the following error message is received: "Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 Recipient address rejected: User unknown (state 14)." When I try to send an e-mail to the same folder, using the same e-mail address above ([email protected]), but with domain2.com instead of domain3.com, it works as intended (both internal & external). I have checked, double checked, and triple checked my DNS settings comparing those from domain2 & domain3 with them both appearing identical. I have tried recreating the folders in question with the same results. I have also ran Get-PublicFolderClientPermission "\Web Programs\folder" with the following results for user anonymous: RunspaceId : 5ff99653-a8c3-4619-8eeb-abc723dc908b Identity : \Web Programs\folder User : Anonymous AccessRights : {CreateItems} Domain2.com & Domain3.com are duplicates of each other, but only domain2.com works as intended. All other exchange functions are functioning properly. If anyone out there has any suggestions, I would love to hear them. I've just hit a brick wall. Thanks for all your help in advance! --Alex

    Read the article

  • Can't access my accelerated hard disk from msdos after installing linux on ssd cache

    - by Chibueze Opata
    I mistakenly installed Linux Mint on my ssd (forgot my PC actually came with one), when it detected a ~31GiB disk that it wanted to install to, I was a bit confused since I had brought out 30Gb in my primary disk for it, but I clicked continue. After installation, I tried to boot back into my Windows and it brought out some Intel Raid Disk Utility stuff saying I should disable acceleration on a disk something couldn't be found, I canceled it but whatever I tried, recovery tools, setups etc, I couldn't just access the drive which was apparently using the SSD as cache. Since then I've been stuck. I tried setting the 'raid' flag to the disk from 'gParted', still I couldn't. I tried the diskraid utility from windows recover disk, it said it couldn't detect any raid, diskpart sees the partition but doesn't see the volume, when I remove the raid flag, it sees the volume as one of raw type, and I can't access anything. I can however mount the drive from terminal in Mint and access my files, but I don't have any backup media at the moment so I can do a factory re-install. Please how do I go about solving the issue, precisely I would like to know how to boot into the drive again. Thanks!

    Read the article

  • Secondary backup server

    - by verdy
    I've been given a task to implement a backup solution in the event of our website goes down. It is a dedicated server running centos 6. From what i've experience on our server, our server may go down because of PHP application crash or hardware failure. I have couple of questions: In the first case, is it possible to get the server restart the PHP automatically, how can I do that? Because in my mind, if it is only the application that goes down, probably I can still make use of the server itself. In the second case, can I redirect a request to a secondary server? How can I do that? What do I need other than another server? For now it is gonna be a simple server which shows the user a static landing page so later the system notify us via email that the primary server went down so that we can restart the server manually. Is it possible to setup just a vps or even a shared server for the secondary server ? As I think there is only gonna be a static page. Thanks. Any help would be much appreciated

    Read the article

  • New router messed up server 2003 setup...

    - by Aceth
    Hey, We were sent a new 2wire router today configured it as best we can to match the old bt voyager. We've also got X static IP's. We've manage to get our webserver on one of the new IP's public facing. then we use a hardware firewall which is in a DMZ again with a different static IP. This firewall then is our gateway for our internal LAN. with a few servers etc. The problem we're having is only our PDC (primary Domain controller which has exchange 2003 on) can't ping externally even an external IP. We've connected laptops to the 2wire router and obtain a private ip 192.168.1.X and it works fine can ping etc. our other servers with an internal ip behind the firewall can ping out fine. We've connected to the firewalls logging console and the pings from the server are allowed through so its fine there. The server in question is a Windows server 2003 R2 Enterprise SP2 + Exchange 2003 Server doesn't have firewall turned on. it has static private IP .. gateway is pointing to the right one External Static IP is routing fine inwards We've ran out of ideas .. help??

    Read the article

  • Error in Bind9 named.conf file. Bind won't start.

    - by tj111
    I'm trying to setup a DNS server on an Ubuntu Server machine (10.04). I configured an entry in named.conf.local to test it, but when trying to restart bind9 I get the following error: * Starting domain name service... bind9 [fail] So I checked the output of syslog and this is what I get. May 20 18:11:13 empression-server1 named[4700]: starting BIND 9.7.0-P1 -u bind May 20 18:11:13 empression-server1 named[4700]: built with '--prefix=/usr' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc/bind' '--localstatedir=/var' '--enable-threads' '--enable-largefile' '--with-libtool' '--enable-shared' '--enable-static' '--with-openssl=/usr' '--with-gssapi=/usr' '--with-gnu-ld' '--with-dlz-postgres=no' '--with-dlz-mysql=no' '--with-dlz-bdb=yes' '--with-dlz-filesystem=yes' '--with-dlz-ldap=yes' '--with-dlz-stub=yes' '--with-geoip=/usr' '--enable-ipv6' 'CFLAGS=-fno-strict-aliasing -DDIG_SIGCHASE -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions' 'CPPFLAGS=' May 20 18:11:13 empression-server1 named[4700]: adjusted limit on open files from 1024 to 1048576 May 20 18:11:13 empression-server1 named[4700]: found 4 CPUs, using 4 worker threads May 20 18:11:13 empression-server1 named[4700]: using up to 4096 sockets May 20 18:11:13 empression-server1 named[4700]: loading configuration from '/etc/bind/named.conf' May 20 18:11:13 empression-server1 named[4700]: /etc/bind/named.conf:10: missing ';' before 'include' May 20 18:11:13 empression-server1 named[4700]: loading configuration: failure May 20 18:11:13 empression-server1 named[4700]: exiting (due to fatal error) So it thinks I have an error in the default named.conf file, which is pretty ridiculous. I went through it and deleted a blank line just for the hell of it, but I can't see how it figures there's an error in there. Note that before this I did have an error in named.conf.local, but it showed up properly in syslog and I fixed it, so it is reporting the correct file. Here is the contents of named.conf: // This is the primary configuration file for the BIND DNS server named. // // Please read /usr/share/doc/bind9/README.Debian.gz for information on the // structure of BIND configuration files in Debian, *BEFORE* you customize // this configuration file. // // If you are just adding zones, please do that in /etc/bind/named.conf.local include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones";

    Read the article

  • W2K INACCESSIBLE_BOOT_DEVICE, with System Commander

    - by Gary Kephart
    I have a system that was originally had Win NT. I added System Commander (SC7) and then added W2K. The relevant partitions are: 0 - Primary - MultiFAT (Has Win NT, mapped to C:) 1 - Extended - with many logical partitions: 1.1 NTFS which has W2K and is mapped to D: 1.2 other logical partitions which are irrelevant to this D: was getting full. It needed room for virus definitions and Windows upgrades. In the past, I had simple used SC7 to resize D: without problems. So I did it again this time. However, upon finishing, I got the message "Unable to create partition". It also marked the partition as unformatted. I checked that the files on the disk were still there using SC7's Partition Explorer, and they were there. I continued and the system managed to boot up fine anyways. Then I rebooted the system again. This time, I got a message saying "INACCESSIBLE_BOOT_DEVICE". I went back in to SC7 and to Partition Commander, and it was still saying that the partition was unformatted but the Partition Explorer still showed the files on the system. I finally decided to resize the partition again, figuring that this would force a rewrite of the partition information. That seemed to work, until I had to reboot again. Now I can't see the files using Partition Explorer, and the Resize button is now disabled. What now?

    Read the article

  • How do I get "Back to My Mac" (using MobileMe) from Windows?

    - by benzado
    I have a MobileMe subscription and a Mac at home with "Back to My Mac" enabled. When I'm away from home, this service lets me use another Mac to connect to my Mac back home and access file sharing, screen sharing, etc. As far as I know, the service doesn't use any proprietary protocols, so in theory I should also be able to get "Back to My Mac" from a Windows PC. This MacWorld article explains how it works. Basically, it uses Wide-Area Bonjour to give your Mac a domain name like hostname.username.members.mac.com. Remote computers can find your Mac using that address, then connect to it using a private VPN. The "Wide Area Bonjour" part seems to make it a little more complicated than simply a regular domain name, though. Note that I'm not interested in using the methods described by LifeHacker, which doesn't use the MobileMe service at all. I don't want to use a totally different dynamic DNS service. I'd like to use the one I'm already paying for, or at least find out why that's not possible from Windows. Also, my primary problem is finding a network route back to my mac... once I've got that I know how to enable services so that Windows can talk to it. UPDATE: Based on some additional research, it appears that Apple is only assigning IPv6 addresses to the hostname.username.members.mac.com names. So any solution will require enabling IPv6 support on Windows, if possible.

    Read the article

  • How to make Exchange 2003 non-authoritive

    - by Romski
    Background We are a small company with an internally hosted Exchange 2003. It receives email for 2 domains (the company was renamed a few years back). For the sake of argument, the domains are: oldname.com newname.com We have moved newname.com to a hosted exchange service, and our DNS record is correctly routing emails. Our internal server still receives email for oldname.com, although we have asked our hosting company to accept emails for that domain. Problem My problem is that emails generated internally from monitoring software, printer, etc. are being caught by our (defunct) internal server and being delivered to the old mailboxes. I believe that what is happening is that our internal exchange server considers itself to be the authoritive server for newname.com. I think it must be looking in active directory for a mailbox and delivering it internally without ever going outside. Attempt to fix I started to follow the article here: http://support.microsoft.com/kb/321721. I removed the SMTP recipient policy for newname.com, and added a dummy address and made it primary. I also answered yes for updating the associated emails. I then restarted the Microsoft Exchange Routing System and SMTP, but emails are still being routed internally. Is there a way to force the exchange server to route all emails for the domain newname.com to the new hosted service?

    Read the article

  • Trying to use a SmartHost with my Exchange 2010 server

    - by Pure.Krome
    Hi folks, I'm trying to use a SmartHost with my Exchange 2010 Server. SmartHost details: Secure SMTPS: securemail.internode.on.net 465 <-- Note: that's port 465 Configure your existing SMTP settings (in your email program) to: use authentication (enter your Internode username and password, enter your username as [email protected]). enable SSL for sending email (SMTPS). So I've added the smart host details to my Org Config -> Hub Transport. I then used PowerShell to add the port:- Set-SendConnector "securemail.internode.on.net" -port 465 I've then added my username/password (as suggested above) to the SmartHost as Basic Authentication (with no TLS). Then I try sending an email and I get the following error message :- 451 4.4.0 Primary target IP address responded with: "421 4.4.2 Connection dropped due to ConnectionReset." So i'm not sure how to continue. I also tried ticking the TLS box but stll I get the same error. If i don't use SMTPS (secure SMTP, on port 465) and use basic SMTP on port 25 with no Authentication, email gets sent. Any ideas? EDIT: Btw, I can telnet to that server on port 465 from my mail server .. just to make sure i'm not getting firewall'd, etc.

    Read the article

  • Cisco VPNClient from Mac won't connect using iPhone Tethering

    - by Dan Short
    I just set up iPhone tethering from my Snow Leopard Macbook Pro to my iPhone 3GS with the Datapro 4GB plan from AT&T. When attempting to connect to my corporate VPN from the MacBook Pro with Cisco VPNClient 4.9.01 (0100) I get the following log information: Cisco Systems VPN Client Version 4.9.01 (0100) Copyright (C) 1998-2006 Cisco Systems, Inc. All Rights Reserved. Client Type(s): Mac OS X Running on: Darwin 10.6.0 Darwin Kernel Version 10.6.0: Wed Nov 10 18:13:17 PST 2010; root:xnu-1504.9.26~3/RELEASE_I386 i386 Config file directory: /etc/opt/cisco-vpnclient 1 13:02:50.791 02/22/2011 Sev=Info/4 CM/0x43100002 Begin connection process 2 13:02:50.791 02/22/2011 Sev=Warning/2 CVPND/0x83400011 Error -28 sending packet. Dst Addr: 0x0AD337FF, Src Addr: 0x0AD33702 (DRVIFACE:1158). 3 13:02:50.791 02/22/2011 Sev=Warning/2 CVPND/0x83400011 Error -28 sending packet. Dst Addr: 0x0A2581FF, Src Addr: 0x0A258102 (DRVIFACE:1158). 4 13:02:50.792 02/22/2011 Sev=Info/4 CM/0x43100004 Establish secure connection using Ethernet 5 13:02:50.792 02/22/2011 Sev=Info/4 CM/0x43100024 Attempt connection with server "209.235.253.115" 6 13:02:50.792 02/22/2011 Sev=Info/4 CVPND/0x43400019 Privilege Separation: binding to port: (500). 7 13:02:50.793 02/22/2011 Sev=Info/4 CVPND/0x43400019 Privilege Separation: binding to port: (4500). 8 13:02:50.793 02/22/2011 Sev=Info/6 IKE/0x4300003B Attempting to establish a connection with 209.235.253.115. 9 13:02:51.293 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 10 13:02:51.894 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 11 13:02:52.495 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 12 13:02:53.096 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 13 13:02:53.698 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 14 13:02:54.299 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 15 13:02:54.299 02/22/2011 Sev=Info/4 IKE/0x43000075 Unable to acquire local IP address after 5 attempts (over 5 seconds), probably due to network socket failure. 16 13:02:54.299 02/22/2011 Sev=Warning/2 IKE/0xC300009A Failed to set up connection data 17 13:02:54.299 02/22/2011 Sev=Info/4 CM/0x4310001C Unable to contact server "209.235.253.115" 18 13:02:54.299 02/22/2011 Sev=Info/5 CM/0x43100025 Initializing CVPNDrv 19 13:02:54.300 02/22/2011 Sev=Info/4 CVPND/0x4340001F Privilege Separation: restoring MTU on primary interface. 20 13:02:54.300 02/22/2011 Sev=Info/4 IKE/0x43000001 IKE received signal to terminate VPN connection 21 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700008 IPSec driver successfully started 22 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 23 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x4370000D Key(s) deleted by Interface (192.168.0.171) 24 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 25 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 26 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 27 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x4370000A IPSec driver successfully stopped The key line is 15: 15 13:02:54.299 02/22/2011 Sev=Info/4 IKE/0x43000075 Unable to acquire local IP address after 5 attempts (over 5 seconds), probably due to network socket failure. I can't find anything online about this. I found a single entry for the error message in Google, and it was a swedish (or some other nordic language site) that didn't have an answer to the question. I've tried connecting through both USB and Bluetooth tethering to the iPhone, and they both return the exact same results. I don't have direct control over the firewall, but if changes are necessary to make it work, I may be able to get the powers-that-be to make adjustments. A solution that doesn't require reconfiguring the firewall would be far better of course... Does anyone know what I can do to make this behave? Thanks, Dan

    Read the article

  • When pointing to new DNS servers is there any chance of E-mails being lost if the old E-mail hosting service is still up?

    - by LaserBeak
    I am changing webhosts and will be using the new hosts mail servers instead of the old ones. I have created all the correctly named mailboxes on the new service but have also not yet cut ties with the old webhost. I am expecting that even if the new DNS values which point to the new hosts DNS servers and respective SOA\zone file with the new MX values have not yet propagated and an E-mail is directed at the old hosts mail servers as per the mx records in the SOA\zone records which the old hosting provider holds, the E-mail would still come through to the mailbox that's on the old host providers mail servers. So I am just trying to reaffirm if I got this right and it's essentially impossible for me to loose an E-mail since it will hit either the old hosts mail servers or the new ones ? Also is it possible to configure the same E-mail account to check and collect mail from different mail servers by entering multiple pop3 addresses ? And if I choose to keep the old web hosts mail hosting services as a backup by specifying the mx records for it with a lower priority in the SOA records hosted by the new webhost, is it possible to have any incoming E-mails sent to both servers by the mail daemon so I have two copies? Or is my only option having the primary mail server forward the E-mail somehow to the old mailserver ?

    Read the article

  • LSI MegaRAID LINUX got Optimal after degradation but strange POST message

    - by kesrut
    Linux server box with LSI MegaRAID controller got degraded. But after some time RAID status changed to Optimal. Adapter 0 -- Virtual Drive Information: Virtual Drive: 0 (Target Id: 0) Name : RAID Level : Primary-1, Secondary-0, RAID Level Qualifier-0 Size : 2.727 TB Mirror Data : 2.727 TB State : Optimal Strip Size : 256 KB Number Of Drives per span:2 Span Depth : 3 Default Cache Policy: WriteBack, ReadAdaptive, Cached, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Cached, No Write Cache if Bad BBU Default Access Policy: Read/Write Current Access Policy: Read/Write Disk Cache Policy : Disk's Default Encryption Type : None Is VD Cached: No But now I'm getting RAID BIOS POST message: Your battery is either charging, bad or missing, and you have VDs configured for write-back mode. Because the battery is not currently usable, these VDs willl actually run in write-through mode until the battery is fully charged or replaced if it is bad or missing. (Image: http://cl.ly/image/1h1O093b1i2d) So may it be battery issue caused problem ? I get information about battery: BatteryType: iBBU Voltage: 4001 mV Current: 0 mA Temperature: 22 C Battery State : Operational BBU Firmware Status: Charging Status : None Voltage : OK Temperature : OK Learn Cycle Requested : No Learn Cycle Active : No Learn Cycle Status : OK Learn Cycle Timeout : No I2c Errors Detected : No Battery Pack Missing : No Battery Replacement required : No Remaining Capacity Low : No Periodic Learn Required : No Transparent Learn : No No space to cache offload : No Pack is about to fail & should be replaced : No Cache Offload premium feature required : No Module microcode update required : No Where can be problem ? I'm disabled alarms, but get them if enabled. But don't know how find root of problem.

    Read the article

  • How to achieve the following RTO & RPO with logshipping only using SQL Server?

    - by Jimmy Chandra
    Trying to come up with viable backup restore & logshipping solution for achieving the following: 15 minutes Recovery Point Objective (no more than 15 minutes data loss at any time) 5 minutes Recovery Time Objective (must be able to get the db up and running back by 5 minutes) Considering using logshipping only (which I think is kind of pushing it, but I want to know if anyone else know how to achieve this). Some other info for consideration: Using 40 Gbit / sec fiber channel between the primary and disaster recovery (DRC) sites The sites are about 600 km apart. At close of business, the amount of data generated is predicted to be about 150 MB/sec. Log backup is planned for every 5 min. Doing some rough calculation I came up w/ the following numbers: 40 Gbit / sec = 5 MB / sec @ 100% network efficiency. 5 MB / sec = 300 MB / min. @ 300 MB / min, the total amount of data that can be transfer considering the 5min RTO is about 1.5GB, but that will left no time for the actual backup and restore, so if we cut it down to 3min logshipping time, which equals to ~900 MB over 3 minutes at 100% network efficiency, that will left about 1 min backup time and 1 minute restore time. Currently don't have any information if the system being used is capable of restoring 900 MB in 1 min, but assume it can. for COB scenario... 150 MB/sec, and considering the 3 min logshipping time, which should equal to about 27 GB of data over 3 mins...??? I think this is where the SLA will break... since there is no way to transfer 27 GB of data over a 40Gbit/sec line in 3 min. Can I get someone else opinion? I am thinking database mirroring might be a better answer for this...

    Read the article

< Previous Page | 535 536 537 538 539 540 541 542 543 544 545 546  | Next Page >