Search Results

Search found 16628 results on 666 pages for 'setup kit'.

Page 539/666 | < Previous Page | 535 536 537 538 539 540 541 542 543 544 545 546  | Next Page >

• RAID 10 or RAID 5 for multiple VMs - what is the best choice?

  - by Lars Fastrup

  I have just ordered a new rig for my business. We do a lot of software development for Microsoft SharePoint and need the rig to run several virtual machines for development and test purposes. We will be using the free VMware ESXi for virtualization. For a start, we plan to build and start the following VMs - all with Windows Server 2008 R2 x64: Active Directory server MS SQL Server 2008 R2 Automated Build Server SharePoint 2010 Server for hosting our public Web site and our internal Intranet for a few people. The load on this server is going to be quite insignificant. 2xSharePoint 2007 development server 2xSharePoint 2010 development server Beyond that we will need to build several SharePoint farms for testing purposes. These VMs will only be started when needed. The specs of the new rig is: Dell R610 rack server 2xIntel XEON E5620 48GB RAM 6x146GB SAS drives Dell H700 RAID controller We believe the new server is going to make our VMs perform a lot better than our existing setup (2xIntel XEON, 16GB RAM, 2x500 GB SATA in RAID 1). But we are not sure about the RAID level for the new rig. Should we go for having the the 6x146GB SAS drives in a RAID 10 configuration or a RAID 5 configuration? RAID 10 seems to offer better write performance and lower risk of a RAID failure. But it comes at a cost of less drive space. Do we need RAID 10 or would RAID 5 also be a good choice for us?

  Read the article

• Why not block ICMP?

  - by Agvorth

  I think I almost have my iptables setup complete on my CentOS 5.3 system. Here is my script... # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP For context, this machine is a Virtual Private Server Web app host. In a previous question, Lee B said that I should "lock down ICMP a bit more." Why not just block it altogether? What would happen if I did that (what bad thing would happen)? If I need to not block ICMP, how could I go about locking it down more?

  Read the article

• VirtualBox with Ubuntu Server guest can't ping outside

  - by Danidan

  Here's my situation: an Ubuntu 12.04 Host running VirtualBox; two guest VMs running Ubuntu Server 12.04 home network, so my Host pc has a wireless connection to the router of my ISP. My problem is in one of the virtual machines: it has 3 NICs, one in NAT mode and the others in Host Only mode. My purpose is to use eth0 (NAT) for Internet access and eth1, eth2 (Host Only) for management of internal virtual network (eth1 uses a VBoxNet with this IP 192.168.69.254). Whenever I try to $ping 8.8.8.8 I get Destination Host Unreachable. While if I $ping 192.168.69.10, that is the IP of the other VM, it works. I can't also ping my Host nor my router My /etc/network/interfaces file is: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 192.168.69.1 netmask 255.255.255.0 auto eth2 iface ifconfig $IFACE 0.0.0.0 up up ip link set $IFACE promisc on down ip link set $IFASE promisc off down ifconfig $IFACE down $route -n returns: Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.2.2 0.0.0.0 UG 100 0 0 eth0 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.69.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Forgetting for now what eth2 needs to do and its setup, why I can't go outside the Host box? What can I do to help you helping me? :-)

  Read the article

• New PC: win7 install issues with 2x3TB in RAID1

  - by goober

  Background / Components Not sure what I've done wrong. Built one PC before successfully in a similar way but this one seems to be struggling. I have the following components: ASUS P8Z68-V/Pro Gen 3 (updated to latest firmware) 16GB (2x8GB) RAM corsair hx850 power supply 2x3TB drives on the intel z68 controller 1x128GB SSD on the Marvel controller sapphire 7950 The problem I set up my 3 TB disks in RAID1 controller appears to recognize them fine during boot as one 2.7TB raid1 volume windows setup sees two disks, both 746 GB, but will only let me install to one and appears to work fine. windows appears to install fine after installer reboots, I receive "windows failed to start" error referencing code 0xc000000e and "\Windows\system32\winload.exe every time I do an install, a new additional "win7" entry is added to the boot menu; all lead to this error. What I've tried: updated the BIOS to the latest firmware attempted to repair the install tried clearing / removing raid / re-raiding drives tried formatting the drives during install attempted to clear the menu Of entries (can't figure out how to do that) No matter how many times I destroy the raid array, format the disks, etc. the boot entries keep piling up. Any idea where I'm going wrong?

  Read the article

• Load balancing with puppet

  - by Gonçalo Queirós

  Hi there. Im trying to setup a loadbalancing system. My load balancer (nginx) has a conf file where i should list all IP's of the upstream servers. I could put the IP's on the conf manually, but this ways i would need to change the conf file every time i add/remove an upstream server. For now i came up with two different ideas, but i don't like much of neither: 1 - Have every upstream machine to use Exported Resources to create a file with it's IP..Then the load balancer server will have an "include conf_directory/*", and load all the files created by the upstrem servers. Since the load balancer is using nginx this can be done, but if i wan't latter on to configure something that doesn't have the "include" on the conf files, this solution will not work. 2 - If the config doesn't support the "include" command, then we could have again, every upstream server use the Exported Resources to create a filw with its IP, and latter on, the load balancer execute a command that would pick every file and generate the config Both versions addopt the same techinque, the difference is that version 2 is used when the server (that needs to have a conf generated) doesn't recognize a command like "include" inside its own conf. Now, my question is, is there any way to do this in a different form? I suspect that there is, since puppet is made to manage multiple servers, it seems a bit strange not have a easy way to configure load balancers.

  Read the article

• Weird Apache behaviour and with files again

  - by afifio

  Hi and thanks for stopping by. I have read Weird Apache problem with file, I have read Weird Apache problem with file ...and its not the problem Setup single XAMPP installation on Windows, single windows user, 2HD, 1 is a portable USB. All is fine, until I move the xampp to new portable HD Symptom Old php files - works fine, new one doesnt http://127.0.0.1/Ajax/index.php - yay http://127.0.0.1/test2/t.php - display the source code http://127.0.0.1/Ajax/test2/t.php - display the source code http://127.0.0.1/Ajax/t.php - display the source code Extra Info IIS+MS Web Development stuff, .NET4, Asp, etc is being installed and still hast reboot yet. .htaccess also seems doesnt work Apache2 conf file was modified to Averride All and still it doesnt care. One of the directory supposed to treat .htm as php yet got text, created another directory and edit a phpinfo, still another text, browse to phpmyadmin, viola, works fine Suspect Does Apache honour XP security and permission ? If so, this is a single user computer. Does Apache dont like my new hard disk/new place ? Why it doesnt execute the php in new directory but happily execute in old folder ? Thanks for the riddle answers

  Read the article

• Formula-based Excel page headers

  - by Jake Krohn

  I'm using the "Rows to repeat at top" function in Excel's "Page Setup" dialog to ensure that a multi-row header block appears on every printed page of my worksheet. However, I'd like to be able to change certain bits of the header based on the content of the current page. I would simply like to display the value of one cell in the first row that is printed on the page. If this is my header: Section: xx And the data looks like this (columns are Section and Name): 1 Foo 1 Bar 2 Baz I want the "xx" in the header to be "1". If, further down on the next page, the value in the Section column is "3", I want that printed in the header of the next page. I originally thought that using the "OFFSET" function might help, e.g. ="Section: "&OFFSET(A2, 1, 0) But it only shows the offset from the original placement of the header, thus only working on page 1. The end document is a PDF, so right now I'm able to go back in with the "TouchUp Text Tool" in Acrobat and add the numbers page by page. But it gets to be a tedious process with 70+ page reports. Anyone have any better ideas that don't require me mucking up the original Excel document with inserted headers every N lines? This is Excel 2008 for Mac, if it makes a difference.

  Read the article

• Windows Not Honoring DHCP Scope

  - by jerhinesmith

  Please bear with me as I'm not a networking person by trade. Our current configuration at work includes two Windows Servers serving as DHCP/Active Directory servers (if that makes sense) -- one replicating from the other. On both machines, the DNS resolution is set up as: Main Windows Box (10...* address) Public IP Address (for Verizon) Public IP Address (secondary Verizon) Secondary Windows Box (10...* address) Assuming our domain is foo.com, we maintain the foo.com website on a hosted VPS with it's own IP address. The problem is that even though bar.foo.com is an internal server and is defined in DNS on the Primary Windows machine, when I ping bar or even bar.foo.com it resolves to the hosted IP address instead of the 10.* address. I tried taking both of the Public IP addresses out of the DHCP scope, and that seemed to work, but it completely slowed down access to any external sites, so that wasn't acceptable. I also tried adding the two Windows machine as the DNS servers on my desktop. That too worked, but I'd rather not have everything enter their DNS servers, as the above setup should theoretically be working. Is there anything I could check to see why pinging bar.foo.com isn't resolving to the DNS entry on the Windows machines? Here's a summary of the ping results, if they help: Pinging from servers with static IP bar.foo.com resolves with correct IP address Pinging from linux machines not joined to the domain bar.foo.com resolves with correct IP address Pinging from user's desktop machines, joined to the domain, but dynamic IP bar.foo.com resolves with incorrect IP address This is driving me crazy!

  Read the article

• IBM BladeCenter S: Disk Configuration

  - by gravyface

  Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

  Read the article

• Windows Small Business System 2003. SQL timeout in Server Performance Report

  - by tetranz

  I'm the volunteer IT admin at a small school. We have SBS 2003 with about ten desktops. The server performance report is emailed to me daily. It is setup with a wizard in the Monitoring and Performance part of the "Server Management" console. It often fails with a "The page cannot be displayed" error. The event log shows Event Type: Error Event Source: ServerStatusReports Event Category: None Event ID: 1 Date: 1/16/2011 Time: 6:03:14 AM User: N/A Computer: ALPHA Description: Server Status Report: URL: http://localhost/monitoring/perf.aspx?reportMode=1&allHours=1 Error Message: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. Stack Trace: at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, TdsParserState state) at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, TdsParserState state) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning() at System.Data.SqlClient.TdsParser.ReadNetlib(Int32 bytesExpected) [plus lots more stack trace] This has been happening for years :) I've never really solved it. It seems to be related to WSUS. When it happens, I run the Update Services "Server Cleanup Wizard". That takes a long time to run. If I haven't run it for a while it can take 10 hours. I also run the WsusDBMaintenance.sql script (from TechNet I think) which reindexes the database etc. Those two things seem to get it working again for a while. Recently the "while" has become a couple of weeks. My searching online has revealed lots of people having this problem but no real solution. Does anyone have any good ideas about this? I have to wonder if something in the WSUS SQL schema is not indexed properly. The time that the server cleanup wizard takes seems ridiculous. Thanks

  Read the article

• Handling emails on a web server - Making sure the FQDN is set correctly based on the website sending the email

  - by webnoob

  I have a Windows 2008 Web Edition server hosting multiple websites using IIS 7.5. At the moment, all the emails are sent via the IIS6 SMTP service. The FQDN of the SMTP service is set to the computer name at the moment which isn't correct as it doesn't resolve to a valid DNS entry and is not RFC compliant. Some questions: Is there any way I can change the FQDN of the SMTP service based on the site sending the email? Would it be Ok to just setup mailserver.mydomain.com and use that as the FQDN for all the sites on multiple domains. Should I be using some other mail server software to handle this better? The reason I am asking is lots of emails are hitting spam folders because the settings are incorrect. I have access to the code that is running the websites so if something needs to be done there then that shouldn't be a problem. The sites are written using ASP.NET 2.0. EDIT: I have just found an option to create an SMTP virtual service. Would this be the way forward? Create a virtual server for each site? Thanks.

  Read the article

• Loadbalancing with nginx and tomcat

  - by London

  Hello this should be fairly easy to answer for any system admin, the problem is that I'm not server admin but I have to complete this task, I'm very close but still not managing to do it. Here is what I mean, I have two tomcat instance running on machine1 and machine2. People usually access those by visiting urls : http://machine1:8080/appName http://machine2:9090/appName The problem is when I setup nginx with domain name i.e domain.com, nginx sends requests to http://machine1:8080/ and http://machine2:9090/ instead of http://machine1:8080/ and http://machine2:9090/appName Here is my configuration (very basic as it can be noted) : upstream backend { server machine1:8080; server machine2:9090; } server { listen 80; server_name www.mydomain.com mydomain.com; location / { # needed to forward user's IP address to rails proxy_set_header X-Real-IP $remote_addr; # needed for HTTPS proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_max_temp_file_size 0; proxy_pass http://backend; } #end location } #end server What changes must I do to do the following : - when user visits mydomain.com - transfer him to either machine1:8080/appName or machine2:9090 Thank you

  Read the article

• How can I keep SSH's know_hosts up to date (semi-securely)?

  - by Chas. Owens

  Just to get this out in front so I am not told not to do this: The machines in question are all on a local network with little to no internet access (they aren't even well connected to the corporate network) Everyone who has the ability to setup a man-in-the-middle attack already has root on the machine The machines are reinstalled as part of QA procedures, so having new host keys is important (we need to see how the other machines react); I am only trying to make my machine nicer to use. I do a lot of reinstalls on machines which changes their host keys. This necessitates going into ~/.ssh/known_hosts on my machine and blowing away to old key and adding the new key. This is a massive pain in the tuckus, so I have started considering ways to automate this. I don't want to just blindly accept any host key, so patching OpenSSH to ignore host keys is out. I have considered creating a wrapper around the ssh command the will detect the error coming back from ssh and present me with a prompt to delete the old key or quit. I have also considered creating a daemon that would fetch the latest host key from a machine on a whitelist (there are about twenty machines that are being constantly reinstalled) and replace the old host key in known_hosts. How would you automate this process?

  Read the article

• centos install / partitioning

  - by ServerSideX

  I'm using NOC-PS to remotely install Centos 6.2 via KVM / IPMI. I'm going to install cPanel as well and they recommend this layout /boot (99MB) swap (2x server RAM) / (remainder) In the o/s install profile within NOC-PS software, it shows as this: part /boot --fstype ext2 --size 250 part pv.01 --size 1 --grow volgroup vg pv.01 logvol / --vgname=vg --size=1 --grow --fstype ext4 --fsoptions=discard,noatime --name=root logvol /tmp --vgname=vg --size=1024 --fstype ext4 --fsoptions=discard,noatime --name=tmp logvol swap --vgname=vg --recommended --name=swap By the time the default partition setup was done installing Centos, I get this [root@server005 ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg-root 532G 907M 504G 1% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 243M 28M 202M 13% /boot /dev/mapper/vg-tmp 1008M 34M 924M 4% /tmp [root@server005 ~]# cat /etc/fstab # # /etc/fstab # Created by anaconda on Fri Dec 7 18:47:24 2012 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg-root / ext4 discard,noatime 1 1 UUID=58b31aaf-5072-4fb1-a858-33bc316fa793 /boot ext2 defaults 1 2 /dev/mapper/vg-tmp /tmp ext4 discard,noatime 1 2 /dev/mapper/vg-swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 My question is, how should the NOC-PS install profile look like to get the recommended cPanel partitioning? The server has 16GB RAM, dual 600GB SAS drives and will be used for cPanel shared hosting.

  Read the article

• Access server using IP on another interface

  - by Markos

  I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

  Read the article

• Expresscard Not Detected in PCI-E Adapter

  - by maxpower47

  I'm trying to put an expresscard TV tuner (Avermedia HC82) into my HTPC using this expresscard to PCI-E adapter. I've verified that the tuner works fine in my laptop. The motherboard is a Biostar TF7050-M2. When I install it and turn it on, the light on the back of the adapter comes on fine (there are two indicator lights on the back to show if it is using PCI-E or USB communication, USB communication goes through a USB cable connected between the card and a header on the motherboard) showing that it is working in PCI-E mode. However, the device is never detected in Windows 7 Professional x64. The auto detect never happens, it doesn't show up in the device manager, and I can have it rescan for new hardware and nothing is found. I tested the whole setup (tuner + adapter) in another PC (also using Win 7 Pro x64) and it worked fine. I also tried: Plugging the adapter in to the PCI-E x16 slot on the motherboard (I verified first that the x16 slot worked by installing a video card in it) Booting into safe mode and rescanning Updating the chipset drivers Installing the tuner drivers first Using a different USB cable, plugged in to one of the known good ports on the back of the board Trying it without the USB cable plugged in Removing the other PCI cards that were installed on the board Looking through the BIOS for any setting that might be disabling it somehow to no avail. I'm at a loss for what else to try. I really don't want to RMA it (the shipping back to newegg will be almost as much as it cost to buy in the first place. Any ideas?

  Read the article

• Enter network credentials as part of batch script

  - by Michael

  WinXP: I have several system services that are needed to run some machinery in my lab. The machine these services are running uses a lab login that has administrator rights. Our IS department, unfortunately, has it set up where at some point during the night the login "loses" the privilege level to start/stop these services. The account stays logged in, but the software controlling my hardware becomes unresponsive. In order to get things back up and running, I have to stop the system services and restart them. Because of the security settings, however, I have to re-enter the user password to start the service (even though the user was never logged out). That, I get the "This service cannot be started due to a logon failure" and I have to enter the password. What would be ideal is to have a batch script run before anyone gets into work that stops all of the necessary services, enters the user credentials when prompted, and then restarts them so that everything is ready for first shift to run. I assumed that using the Task Scheduler in Windows would work as it allows you to run batch files with a user's name and password, but this didn't seem to do the trick. With this setup I would arrive to find that all the services are stopped but not started again. (Presumably because the authentication failed.) The batch file is about as simple as it gets, all I have is: net stop "Service1" net stop "Serivce2" etc., then restart in reverse order based on dependency: net start "Service2" net start "Serivce1" What would it take to accomplish what I'm trying to do and restart the services?

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• Remote access to phpmyadmin from computer belongs to same LAN

  - by Charles

  OK... I solved it. It is because I have not configured the httpd.conf to allow the centos listen port 80 and 8080. Listen 80 Listen 8080 I have setup the myphpadmin on my CentOS 6.4 recently. I can access and login to the myphpadmin on my localhost. However, when I type http://[hostipaddr]/phpmyadmin on my other computer in the same LAN with the CentOS, the browser simply cannot access the page. Below are some of the current configuration. Anyone can help please......? config.inc.php $i++; /* Authentication type */ $cfg['Servers'][$i]['auth_type'] = 'http'; /* Server parameters */ $cfg['Servers'][$i]['host'] = 'localhost'; $cfg['Servers'][$i]['connect_type'] = 'tcp'; $cfg['Servers'][$i]['compress'] = false; /* Select mysql if your server does not have mysqli */ $cfg['Servers'][$i]['extension'] = 'mysql'; $cfg['Servers'][$i]['AllowNoPassword'] = false; phpmyadmin.conf <Directory /var/www/html/phpmyadmin/> order allow,deny allow from all </Directory> Furthermore, I can access the webpage that stored in the CentOS from my other computer without problems. After using wireshark and tcpdump, I found that the server (the Cent OS) keep resetting the connection. (192.168.1.106 is my other computer, 192.168.1.101 is my CentOS) 23:29:42.281473 IP 192.168.1.106.55999 > 192.168.1.101.webcache: Flags [S], seq 2559409090, win 65535, options [mss 1460,nop,wscale 8,nop,nop,sackOK], length 0 23:29:42.281504 IP 192.168.1.101.webcache > 192.168.1.106.55999: Flags [R.], seq 0, ack 2559409091, win 0, length 0 I have disabled the iptables service on the CentOS already.

  Read the article

• Shortcut To Full Screen App In Lion

  - by omghai2u

  I postponed getting OSX Lion for as long as I possibly could. Now that I have it, I'm having lots of difficulties getting it to perform how I want. On Snow Leopard my typical setup for working was 4 spaces. I'd keep a Windows VM open on Space #4 full-screened, a Linux open on space #3, and I'd do other stuff on spaces #1 and #2. My keyboard shortcut allowed me to switch between my Windows work (Command + 4) to my Linux work (Command + 3) very quickly, and without the need for my hands to leave the keyboard (or effectively to even quit typing). Productivity was good. I see that on Lion a full-screened VM (and yes, they need to be full screened, Fusion's Unity won't cut it for what I need to do) is its own separate Desktop. I have set up 4 desktops and made my keyboard shortcuts to move between them Command + # just as before. But how do I get my full-screened VM to be one of those already existing desktops? Or, rather, how do I make a short-cut for the full-screened app?

  Read the article

• UW-IMAP server, high load for one user

  - by Bruce Garlock

  We have been experiencing a very strange anomaly, with one specific user with our UW-IMAP server. We have about 75 users using the server, and one particular user, who is in about the middle as far as used storage keeps having issues with slow speed. Most of our users all use Thunderbird 2, or Thunderbird 3. Mostly 2, because of the performance issues we have had with 3. This user was on 3, and I downgraded him to 2. The performance has gotten better, but according to the imapd processes on the server, his username is using the most CPU % and CPU time. I've already done all the usual T/S'ing: Started profile from scratch, compacted folders, re-indexed, newer faster computer, etc.. Still, this users' imapd process is always using the most CPU on the server. For troubleshooting, we setup another user which has more usage, folders, etc.. than he does, but we don't see the users process taking up most of the CPU with the imapd process. So, it almost sounds like a particular email may be the culprit, but how can we find it, if thats the problem? This has been going on for a while, and he is a management person, so his patience is about to end. Does anyone have any ideas?

  Read the article

• javascript doesn't seem to be able to post form data (nginx server w/ php-fpm)

  - by Jones

  So the situation is like so: I have a nginx server with php-fpm installed. All is well and the site scripts and all work perfectly. I am able to use html to POST form data and it works just fine. However, There seems to be be some correlation between javascript, the POST protocol and nothing happening. I cant seem to determine the issue. Example: I have a user login widget that uses javascript on submit the fields and POST the data to a backend auth script which returns a server message that then populates the login box saying something like "Login Successful" followed by reloading the page to properly enable content. Problem is, nothing happens when you hit submit. I do know the setup works because i had it working on apache before migrating. Also if it makes any difference, the server is a Amazon EC2 instance using the Amazon AMI. I really dont know where to start looking on this one, but below is my default.conf for the server: upstream backend_get { server 127.0.0.1:80 weight=1; } upstream backend_post { server 127.0.0.1:80 weight=1; } #Main website url server { listen 80; server_name server.com; #charset koi8-r; access_log logs/host.access.log main; error_log logs/host.error.log; location / { root /usr/share/nginx/html; index index.php index.html index.htm; if ($request_method = POST) { proxy_pass http://backend_post; break; } } location ~ \.php$ { #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/run/php-fpm/php-fpm.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } }

  Read the article

• Utility to grant admin rights to a user in Windows XP for few hours/days?

  - by user15660

  I have two accounts on my windows xp home desktop. The default regular user is used for everything and the 2nd user which has admin rights is used only for installations. I do this to avoid malware infestations during web browsing and limited user account is guarding against online threats to a good extend but many programs refuse to run under limited rights like revo uninstaller. many installs i run from limited user by selectin "run as" from right click context menu of the .exe file. but some apps need admin rights for certain. I use "switch user" to go to admin mode and do the install/uninstall. but the admin user has none of my preferences bookmarks setup nor has my locate32 indexing done and ready for fast search Is there a utility which I can use "run as" login in administration login and use that to grant my limited user admin rights for a limited amount of period like few hours or days? Please help. I guess MS might have closed many doors of it for fear of exploitation of the API. are there any?

  Read the article

• Office documents on intranet all requiring second login and can't pass auth? Disable webdav?

  - by DOTang

  I am not sure what is going on, but recently all the Office documents on our intranet get prompted a second time for login and according to the error logs it looks like it's trying to use webdav to open (an editable?) version of the document to save directly on the server? We have no sharepoint server setup or anything, but this shouldn't be happening. All I want is for the document to be saved or opened from a local copy in temp like normal. Here is the log: Line 57499: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57500: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57501: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 The log basically contains a bunch of these. How can I disable this behavior so that office documents that are downloaded aren't attempted to be used through webdav?? Edit: I should clarify behavior, it asks if you want to save or open it, upon choosing open open, it asks to re-authenicate, you put in the user information and the login box comes up 3 times acting like you entered the wrong password. For some users, after passing the login box the third time, it still opens up, for others their browser just locks up. It also doesn't even look like webdav is installed on our server, I see no config options in IIS for it as outlined on this page: http://learn.iis.net/page.aspx/350/installing-and-configuring-webdav-on-iis-7/#001

  Read the article

• Smart card driven membership and door entry system

  - by Rob G

  I'm looking at putting in a smart card driven system at my local sports club (which doesn't have oodles of money), and since they're willing to pay for hardware, and I'm willing to do the technical setup, I was wondering if anyone had any experience in setting something like this up. Writing any software needed is not the problem, I've pretty much got that covered with various open source projects out there and custom code I'll write, but it's more the hardware side I'm not too sure about and I'm looking for advice from people out there. I'm sure there are numerous complications, but on the surface it looks fairly simple. I'd basically like to enable members to swipe/touch a smart card at the door to gain entry to the club, walk up to a touch screen PC and swipe/touch a card reader there to "login" to the system I create, which will allow them to book club facilities etc. I may even want that same card to then activate things like lights or music when they enter the room they've booked. Pretty Eutopian I know, but still, we'd like to get as close as we can. As I said, the software shouldn't be a problem, and on the hardware side, so far I'm looking at: All in one touch screen PC running Windows 7 or Ubuntu USB card reader (not sure which one to buy) Smart Cards (again, never bought these before) Door/lighting hardware that could be triggered (not sure here either) If anyone has any advice on implementing something like this - especially the items I'm not sure about above, and of course anything I've missed out that's crucial, I'd be most grateful. Recommended hardware that you've used for something like this would be fantastic!

  Read the article

< Previous Page | 535 536 537 538 539 540 541 542 543 544 545 546  | Next Page >