Search Results

Search found 44742 results on 1790 pages for 'create'.

Page 541/1790 | < Previous Page | 537 538 539 540 541 542 543 544 545 546 547 548  | Next Page >

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• Is there a way to exclude a specific drive vdi from "snapshots" in VirtualBox?

  - by Graza

  ...or is there another space-efficient way of dealing with the page/swap file of the Guest O/S? I've realised that its quite possible/likely that one of the things which "bloats" the snapshot/diff vdi's when a snapshot is taken is the guest operating system's pagefile. For example, say I have a 2Gb swap-file in a Windows guest OS, and over the course of a few weeks the usage of the swap file has gone over 1Gb a couple of times. When I next create a snapshot, it seems likely that I'd be almost guaranteed around 1Gb of space taken up in the new differencing disk just because of changes in the swap file. Obviously (provided I never did "live" snapshots on running or paused machines, and only ever did them when the machine was shut down), I would not need any of the information in the swap file to be saved. So this would simply be a waste of 1Gb. I'm wondering if there's a way to attach a vdi to a VM and flag it as "exclude from snapshots" - which would mean I could put the swap file on a different vdi which would never be included in a snapshot. Or if anyone has any other suggestions. Or an explanation about why it might not be an issue. I could obviously delete and recreate a swap drive vdi every time I did a snapshot to achieve the same effect, but this is a little more effort than simply clicking "create snapshot"....

  Read the article

• How to make the ec2 ami work on the Xen on Debian

  - by user67103

  Hi. Here is the scenario. We are creating a cloud App. We have a Debian on which we create a customized image and upload it to the Amazon EC2. After uploading it to the cloud we have made some more customizations and are trying to rebundle it. We are facing some issues in rebundling it. We would like to know if we could do something like this. a. Create an AMI Image on Debian b. Load it on to the Xen Hypervisor which would be over the Debian c. Customize the image d. Save the customized image e. Upload it to EC2. The issue is that I am unable to find a proper solution on how to install Xen on Debian and will the AMI on Xen work on EC2. Any suggestions/Help would be greatly appreciated. thanks. Krishna

  Read the article

• How do I add a WMware ESXi Host to Microsoft Virtual Machine Manager?

  - by user63250

  I am trying to manage virtual machines running on a VMware ESXi host using Microsoft System Center Virtual Machine Manager. I was able to add the ESXi machine using the "Add VMware VirtualCenter server" option, but can't access any of the VMs on the datastore associated with this ESXi server. The datastore of the ESXi box is showing up with the correct name, but it won't let me see any of the VMs that have already been created; I get "There are no virtual machines on this host." Because I couldn't get any of the existing virtual machines to show up, I tried creating some new ones. When using VMM to connect to ESXi and create new VMs, I get the following error messages in the "rating explanation" section: The virtualization software on the selected host does not support virtual hard disks on an IDE bus. and The virtualization software on the host XXXXXX does not support the creation of dynamic virtual hard disk. Any ideas on why I can't manage existing machines and why I can't create new ones? The existing machines were created in vSphere. I should note that the ESXi server and the server running SCVMM are both on the same domain. I should also note that although the ESXi box has been added as a VirtualCetner server, when I try to add it through the "Add Host" option, I get an error message saying "Virtual Machine Manager cannot complete the VirtualCenter action on server EXSi because of the following error: The operation is not supported on the object."

  Read the article

• How do I rename my old Program Files folder?

  - by SteveJ

  I installed a new SSD as my boot drive (C:), installed a fresh version of Windows 7 64-bit, and kept my existing SATA drive in the system (D:). I want to keep using my D: drive for file storage (no sense filling up the SSD with stuff that isn't performance critical) and I haven't formatted the D: drive because there's stuff on there I want to keep. I also want to create a new "D:\Program Files" folder so I can install apps that aren't performance-critical there. So I decided I'd rename the existing "D:\Program Files" from my old Windows install to "D:\Old Program Files" and then create a new "D:\Program Files" directory. Easy, right? I can see "D:\Program Files" just fine in Explorer. I right click, select Rename, and type "Old Program Files." I get the alert that says I need Admin permission to do this, so I press the confirm button with the shield. But the folder still appears as "Program Files" in Explorer. I jump out to the command line, and it appears as "Old Program Files" when I do a dir. I can even do mkdir "Program Files" and when I do a dir they both appear. But in the Explorer GUI, it looks like I have two "Program Files" folders. This will be confusing during app installation because I won't be able to tell which one is which. I've tried poking around in the properties tab of the old folder, but can't find anything that would explain what's causing the issue. How do I rename the old Program Files folder?

  Read the article

• SubDomain creation issue.Ubuntu 12.04 Apache 2.22 Webmin

  - by anarchos78

  I have a technical question concerning subdomains. My installation is UBUNTU 12.04 and WEBMIN for administration (using Apache web server). I am trying to create a subdomain to one IP (the domain is www.ithemis.gr and I want to create test.ithemis.gr and/or test1.ithemis.gr) with no success. I think I've tried the right way to set subdomains. The address does not resolving (I have already created DNS records via BIND). Do you have any suggestions? I am very new in server administration. Any help will be greatly appreciated! Apache configuration: In /etc/apache2/sites-available: Conf file:www.ithemis.gr.conf (main website) <VirtualHost 184.171.255.110:80> DocumentRoot /home/ithemis.gr ServerName www.ithemis.gr <Directory "/home/ithemis.gr"> allow from all #Options +Indexes Options +Includes -Indexes </Directory> </VirtualHost> Conf file:www.test.ithemis.gr.conf (subdomain website): <VirtualHost *:80> DocumentRoot /home/test.ithemis.gr ServerName test.ithemis.gr <Directory "/home/test.ithemis.gr"> allow from all Options +Indexes </Directory> </VirtualHost> My DNS records: Master Zone: ithemis.gr Name Type TTL Values ithemis.gr. NS Default ns1.themis.gr. ithemis.gr. A Default 184.171.255.110 ns1.ithemis.gr. A Default 184.171.255.110 ns2.ithemis.gr. A Default 184.171.255.110 mail.ithemis.gr. A Default 184.171.255.110 www.ithemis.gr. CNAME Default ithemis.gr. ithemis.gr. MX Default 5 mail.ithemis.gr. www.test.ithemis.gr. CNAME Default ithemis.gr. test.ithemis.gr. CNAME Default ithemis.gr.

  Read the article

• MySQL ADO.NET Connector & MSSQL Integration Services

  - by user1114330

  Here I am, day three... attempting to sync a data view on a Windows Vista box (64 bit) running MSSQL 2012 and Visual Studio 2010. Sanity is slipping and hunger for progress fills my attention. I went through hell trying to get the MySQL ODBC drivers to get the job but to no avail...everyone seems to be lost and all the threads I can find are solutions that do not work for me. The problem: System DSN's not being seen by SSIS. SSIS DSN Not Showing as ODBC Data Source I make the decision to try out the ADO.NET connector...and to my surprise it is actually in the selection list in data sources in SSIS. So I take off running to create a Data Flow Task, create an ADO.NET Source (a local MSSQL DB)...all is good as usual. Then I move swiftly to creating a ADO.NET Destination, enter my credentials...wow, I am selecting a database finally on my linux server! Happy thinking that I finally have figured a way to get the job done. Then I move to mappings...nope, something is wrong...I am getting an error that hurts my eyes: Pipeline component has returned HRESULT error code 0xC0208457 from a a method call. Error at Data Flow Task [ADO NET Destination [81]]: Failed to get properties of external columns. The table name you entered may not exist or you do not have SELECT permission on the table object and an alternative attempt to get column properties through connection has failed. Detailed error messages are" You have an error in your SQL syntax check the manual that corresponds to your MySQL server version for the right syntax to use near "database".tablename" at line 1. The descriptor files on path C:\Program Files (x86)\Microsoft SQL Server\110\DTS\ProviderDescriptors\ does not contain schema information for connection of type MySQL.Data.MySqlClient.MySqlConnection. So it looks like it can't the information and therefore I cannot map the tables properly. Any ideas on this would be ultra helpful...thanks in advance to All!

  Read the article

• 'Bug in Mailman version 2.1.12'

  - by davorg

  I'm working on setting up a server running Plesk 10.4.4 Update #13 on Centos 6.2. I've configured Mailman and now I want to set up some mailing lists. I've created a list in the Plesk control panel, but when I try to administer the new list (by visiting http://lists.[domain].com/mailman/admin/[listname] I see the following error: Bug in Mailman version 2.1.12 We're sorry, we hit a bug! Please inform the webmaster for this site of this problem. Printing of traceback and other system information has been explicitly inhibited, but the webmaster can find this information in the Mailman error logs. I see exactly the same error if I try to go to the list info page at http://lists.[domain].com/mailman/listinfo/[listname]. I would follow the instructions and look in the error logs, but I can't find them. I would expect to find a file at /var/log/mailman/error, but there's nothing there. My test list seems to work correctly. It sends all the expected email. It's just the web pages for the list that seem to be broken. Has anyone else seen this? Any suggestions for tracking down and fixing the problem? p.s. I think I've chosen the correct Stack Exchange site, but it this question would be better asked elsewhere, please let me know. Update: I got to the bottom of this, so I'm documenting the answer in case anyone else has the same problem. The fact that I couldn't find the error log was the clue. The problem was that the Mailman process didn't have permissions to create an error log. And it seems that if Mailman can't create an error log then it will respond to any web request with this error page. Creating an error log file (in /var/log/mailman/error) and giving it the correct permissions fixed the problem.

  Read the article

• Windows file association for README, INSTALL, LICENSE and the like [closed]

  - by Lumi

  Possible Duplicate: How to set the default program for opening files without an extension in Windows? Many files originating in the UNIX world come without file extension. Popular examples include README, INSTALL, LICENSE. We know for a fact that these are text files. It is therefore a bit disappointing not to be able to just double-click them open in Explorer and see them in Notepad (actually, Notepad2 because of the UNIX line endings which silly Microsoft Notepad doesn't render correctly). Does anyone know of a way to create a file association for, say, README files without extension? This could then be replicated to cover the most frequently occurring file types, and then double-clicking them open would work. Update (Sort of in response to all your comments.) Thanks, folks, your comments and answers have helped me. @Indrek, yes, I was under the assumption that you could somehow create an association for just README or Makefile, and couldn't do so for files without extension. Turns out the contrary is true, and yes, that is a workaround that neatly solves the issue. Ultimately, I just want to be able to double-click to open a README or Makefile, that's all. @Sampo, the SendMe trick is also useful, although usability is not as great as a straight double-click. (I'm really lazy sometimes.) Turns out the following trick using ftype and ftype from an Administrator prompt does the double-click enabling job: assoc .=no_ext ftype no_ext=%SystemRoot%\system32\NOTEPAD.EXE %1 :: You can see it created some entries in the registry: reg query hkcr\no_ext /s reg query hkcr\. /s

  Read the article

• BIND zones and named files

  - by preethika

  I've installed BIND in my Windows server2003. i've configured the named file in C:\named\etc\named.conf as: options { directory "c:\named\zones"; allow-transfer { none; }; recursion no; }; zone "tisdns.com" IN { type master; file "db.tisdns.com.txt"; allow-transfer { none; }; }; My zone file is configured in C:\named\zones\db.tisdns.com.txt as: $TTL 6h @ IN SOA ns1.tisdns.com. hostmaster.tisdns.co… ( 2010010901 10800 3600 604800 86400 ) @ NS ns1.tisdns.com. ns1 IN A 192.168.0.17 mug IN A 192.168.0.103 key "rndc-key" { algorithm hmac-md5; secret "M0oW24WFQZhMu9wTq8qepw=="; }; controls { inet 127.0.0.1 port 53 allow { 127.0.0.1; } keys { "rndc-key"; }; }; In the above i've given the name to the domain as "tisdns". i want to create a new domain name in a different zone file. how can i create it?

  Read the article

• What is the fastest way to clone an INNODB table within the same server?

  - by Vic

  Our development server is a replication slave of our production server. We have a script that developers use if they want to run their applications/bug fixes against fresh data. That script looks like this: dbs=( analytics auth logs users ) server=localhost conn="-h ${server} -u ${username} --password=${password}" # Stop the replication client so we don't encounter weird data. echo "STOP SLAVE" | mysql ${conn} # Bunch of bulk insert optimizations echo "SET autocommit=0" | mysql ${conn} echo "SET unique_checks=0" | mysql ${conn} echo "SET foreign_key_checks=0" | mysql ${conn} # Restore all databases and tables. for sourcedb in ${dbs[*]} do destdb=${prefix}${sourcedb} echo "Dropping database ${destdb}..." echo "DROP DATABASE IF EXISTS ${destdb}" | mysql ${conn} echo "CREATE DATABASE ${destdb}" | mysql ${conn} # First, all the tables. for table in `echo "SHOW FULL TABLES WHERE Table_type <> 'VIEW'" | mysql $conn $sourcedb | tail -n +2`; do if [[ "${table}" != 'BASE' && "${table}" != 'TABLE' && "${table}" != 'VIEW' ]] ; then createTable=`echo "SHOW CREATE TABLE ${table}"|mysql -B -r $conn $sourcedb|tail -n +2|cut -f 2-` echo "Restoring ${destdb}/${table}..." echo "$createTable ;" | mysql $conn $destdb insertData="INSERT INTO ${destdb}.${table} SELECT * FROM ${sourcedb}.${table}" echo "$insertData" | mysql $conn $destdb fi fi done done echo "SET foreign_key_checks=1" | mysql ${conn} echo "SET unique_checks=1" | mysql ${conn} echo "COMMIT" | mysql ${conn} # Restart the replication client echo "START SLAVE" | mysql ${conn} All of these operations are, as I mentioned, within the same server. Is there a faster way to clone the tables I'm not seeing? They're all INNODB tables. Thanks!

  Read the article

• How to place a virtual machine in DMZ?

  - by Giordano

  I have an Ubuntu 12.04 server running few virtual machines with KVM. I would like to expose some of these virtual machines on the internet, to make it possible for customers to test the products we're developing and make available other products for demo purposes. One of the server NICs is configured with a public IP. However before exposing anything on the web I would like to be sure that if one of the virtual machines get compromised, the attacker doesn't reach the rest of the hosts. What I would like to do is to put these virtual machines into a DMZ. These are the steps I'm planning to do: Create a tap interface in the virtualization host (let's say tap1) Create a bridge using tap1 and give it an IP in a subnet separate from the other hosts. Let's say 10.0.0.1 Attach the DMZ virtual machines to the bridge and configure their IP statically (10.0.0.2, 10.0.0.3, etc...) Using UFW, forbid any traffic from 10.0.0.0/24 to any of the internal hosts, allow the traffic from the internal hosts towards 10.0.0.0/24 and expose the virtual machines on the web using port forwarding. Do you think this setup is safe? Can you suggest any improvement or a better/safer approach? Thanks in advance!

  Read the article

• Struggling with proper way to setup Permissions on Linux/Apache Web Server

  - by Dr. DOT

  Your expert experience and assistance is great, greatly appreciated here. I have been running a LAMP server for a long time, yet I still struggle with the best way to set file & directory permissions for FTP and WWW protocol activity. My Control panel is WHM/cPanel (not that it makes a difference), and out-of-the box: files are owned by the user account setup in WHM (eg, "abc") files have a group setting of "abc" as well file permissions are created with 644 directories are owned by "abc" directories have a group setting of "abc" directories permissions are created with 0755 Again, these are the default permission settings. Now everything is fine with FTP activity, but please advise me if any of these file/directory settings create issues, especially with security. Here's where my struggle comes into play. I have PHP apps that allow a visitor to create, edit, rename, delete, etc. sub-directories and files in certain selected directories. PHP runs as "nobody" on my server. So in order to get my PHP/Web apps to work, I have had to: chown nobody * chgrp nobody * chmod 0777 * to everything in these certain & selected sub-directories. I know this is probably a huge security whole (so don't ask me for any links :) but how should I set all the permissions to allow my FTP user to do his thing while allowing the PHP apps to do their thing will also "minimizing" any security risks and exposures? I know that big CMS systems like Drupal, Joomla, WordPress and so on, handle this. Thanks ahead of time for reading through this and offering your expert advice!

  Read the article

• Hyper-V vss-writer not making current copies

  - by Martinnj

  I'm using diskshadow to backup live Hyper-V machines on a Windows 2008 server. The backup consists of 3 scripts, the first will create the shadow copies and expose them, the second uses robocopy to copy them to a remote location and the third unexposes the shadow copies again. The first script – the one that runs correctly but fails to do what it's supposed to: # DiskShadow script file to backup VM from a Hyper-V host # First, delete any shadow copies of the drives. System Drives needs to be included. Delete Shadows volume C: Delete Shadows volume D: Delete Shadows volume E: #Ensure that shadow copies will persist after DiskShadow has run set context persistent # make sure the path already exists set verbose on begin backup add volume D: alias VirtualDisk add volume C: alias SystemDrive # verify the "Microsoft Hyper-V VSS Writer" writer will be included in the snapshot # NOTE: The writer GUID is exclusive for this install/machine, must be changed on other machines! writer verify {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} create end backup # Backup is exposed as drive X: make sure your drive letter X is not in use Expose %VirtualDisk% X: Exit The next is just a robocopy and then an unexpose. Now, when I run the above script, I get no errors from it, except that the "BITS" writer has been excluded because none of its components are included. That's okay because I really only need the Hyper-V writer. Also I double checked the GUID for the writer, it's correct. During the time when the Hyper-V writer becomes active, 2 things will happen on the guest machines: The Debian/Linux machine will go to a saved state and restore when done, all fine. The Windows guests will "creating vss snapshop-sets" or something similar. Then X: gets exposed and I can copy the .vhd files over. The problem is, for some reason, the VHD files I get over seems to be old copies, they miss files, users and updates that are on the actual machines. I also tried putting the machines in a saved sate manually, didn't change the outcome. I hope someone here has an idea of how to solve this.

  Read the article

• Outlook locking network connection/session?

  - by HaydnWVN

  Scenario: We have an 'automatic orders' machine sat in the corner running XP with Outlook 2003. Its job is to check for new emails on a specific account, when it encounters one it checks the e-mail body for specific wording to determine which customer it is from (using a macro), then it checks the attachment for specific order codes before parsing the attachment to create a .csv file (which is then e-mailed onto one of the sales team) before importing the .csv into our bespoke ERP/Sales Order system to create an order. Problem: Periodically the machine will have symptoms of a lost network connection (unable to connect to any network source). Sometimes after several days, sometimes over a week. Volume of emails/orders processed does not seem to be linked. Additional info: The machines .pst is stored on a mapped network location. The .csv created is stored on a mapped network location. This is a workgroup, not a domain. All network drives are Samba shares from an Ubuntu fileserver. Our bespoke system runs from a database (MySQL) Ubuntu server. Our troubleshooting so far: I have switched machines (previous was Win2000) with the same symptoms. Restarting the machine FIXES the problem. Closing Outlook and then end tasking an Outlook.exe background process FIXES the problem. If you close Outlook, without end taking the background process, outlook will not reopen (saying it cannot find the pst file & it will not open any network location). Does Outlook have some kind of 'max session' linking it to network activity that is not closing after a mail request? Could Auto-archive be causing this? Is there a tool to check/display what each outlook.exe process is doing? Have not found many ways to troubleshoot this yet, as it is so infrequent...

  Read the article

• How do I increase the buffer size for domain sockets in OS X 10.6

  - by Chas. Owens

  In Linux I have no problem dumping tons of data into a domain socket, but the same code on OS X 10.6.2 blows up after about 65 records. The socket reader code looks like #!/usr/bin/perl use strict; use warnings; use IO::Socket; unlink "foo"; my $sock = IO::Socket::UNIX->new ( Local => 'foo', Type => SOCK_DGRAM, Timeout => 600, ) or die "Could not create socket: $!\n"; while (<$sock>) { chomp; print "[$_]\n"; } And the client code looks like #!/usr/bin/perl use strict; use warnings; use IO::Socket; my $sock = IO::Socket::UNIX->new ( Peer => 'foo', Type => SOCK_DGRAM, Timeout => 600, ) or die "Could not create socket: $!\n"; for my $i (1 .. 1_000_000) { print $sock "$i\n" or die $!; } close $sock; The error message I get is No buffer space available at write.pl line 15.. It seems fairly obvious that there is a difference in the buffer size between Linux and OS X, but I don't know how to set it OS X (or what the possible negative side effects might be).

  Read the article

• Inactive users in windows server after some time according to first login instead of defining a solid expiration date

  - by smhnaji

  We want to give access to some Windows Server users so they can remotely have access to our server and download from a special folder of the server. The licenses we give to users, are time base. There should be 1 month, 2 month, ..., 1 year, ... licenses. CURRENT SITUATION (WHAT I DON'T WANT): When users are created and added to the OS, a solid expiration date is given. WHAT I WANT: Users' expiration date should be calculated automatically after first login. The user might not need his account right when purchases the license. In another words: When a license of the user we create is purchased at Jan 1st, he should use the license until Feb 1st. No matter whether he really logs in or not. He cannot come Feb 5th and begin using his license because that has expired then. What I want is that when he comes at Feb 5th and begins using, the license update until March 5th. CLARIFICATION (Update after MDMarra's comment) Working environment is Windows Server 2012. By the word 'user', I mean Native Windows Server Users. Whenever a new person purchases a license with me, I create them manually using net user command like this: net user ali pass /add /expires:2013-12-25

  Read the article

• Virtualize SBS 2003 - P2V vs migrating to new VM

  - by jlehtinen

  I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

  Read the article

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• Booting Ubuntu as VM with KVM on Ubuntu 12.04

  - by CrazycodeMonkey

  I am trying to boot my very first VM using KVM. I have Ubuntu 12.04 installed, i made sure the BIOS had the right virtualization flag enabled for intel processor by running kvm-ok. I have researched this on google and all the instructions that i have found so far are outdated. for e.g. most instructions talk about booting a virtual machine with the following commands qemu-img create -f qcow2 foo.img 100G --- create a virtual disk for your VM kvm --name foo -m 1024 -hda foo.img -cdrom whatever.iso -boot d -- This runs kvm. This command line is incomplete. First you need to be root to run this. Second- it is missing option for the video device. When you run this command you get the following error "Could not initialize SDL(No available video device) - exiting" Googled this error and looked it up on stackover flow http://stackoverflow.com/questions/4841908/sdl-init-failure-reason-is-no-available-video-device The answer provided here does not work on Ubuntu 12.04 Googled this problem further and found out that i need to specify a video device so I finally ran the following command sudo kvm --name mymachine -m 8096 -hda myimage.img --cdrom ubuntu.iso -boot d -vga cirruss -k en-us -vmc :0 This was after I had created the myimage.img image on the drive. Now this command does not give me an error but it just hangs. Does anyone have clear instructions on how to run a VM using KVM on Ubuntu?

  Read the article

• NAT and P2P router crash

  - by returnFromException

  So..i had this argument with my networks teacher. He said that some people complains about router crashes due to many entrys on NAT tables on a router. I didnt understand and i asked: "If the application uses the same port, why does the router crash?. It should have only one entry (pc-ip,pcport;public-ip,public-port)". And he said: "it doesnt matter its using the same port". I got the idea that NAT creates an entry for every packet that passes trought it. Iam assuming NAT with overloading as you might have guessed. So the questions are: 1-How does nat entrys are created? On a packet basis or connection basis? I mean: suppose i send a udp packet..does the router create an entry? 2-When i start a TCP connection, does the router create a persistant nat entry until the connection closes? 3-Was my teacher right? The NAT table can overload assuming an aplication on the same port sending packets? Thanks in advance.

  Read the article

• How can I automatically synchronize a directory tree on multiple machines?

  - by Blacklight Shining

  I have two Mac laptops and a Debian server, each with a directory that I would like to keep in sync between the three. The solution should meet the following criteria (in rough order of importance): It must not use any third-party service (e.g. Dropbox, SugarSync, Google whatever). This does not include installing additional software (as long as it's free). It must not require me to use specific directories or change my way of storing things. (Dropbox does this IIRC) It must work in all directions (changes made on /any/ machine should be pushed to the others) All data sent must be encrypted (I have ssh keypairs set up already) It must work even when not all machines are available (changes should be pushed to a machine when it comes back online) It must work even when the /directories/ on some machines are not available (they may be stored on disk images which will not always be mounted) This can be solved for Macs by using launchd to automatically launch and kill (or in some way change the behavior of) whatever daemon is used for syncing when the images are mounted and unmounted. It must be immediate (using an event-based system, not a periodic one like cron) It must be flexible (if more machines are added, I should be able to incorporate them easily) I also have some preferences that I would like to be fulfilled, but do not have to be: It should notify me somehow if there are conflicts or other errors. It should recognize symbolic and hard links and create corresponding ones. It should allow me to create a list of exceptions (subdirectories which will not be synced at all). It should not require me to set up port forwarding or otherwise reconfigure a network. This can be solved by using an ssh tunnel with reverse port forwarding. If you have a solution that meets some, but not all of the criteria, please contribute it in the comments as it might be useful in some way, and it might be possible to meet some of the criteria separately. What I tried, and why it didn't work: rsync and lsyncd do not support bidirectional synchronization csync2 is designed for server clusters and does not appear to work with machines with dynamic IPs DRBD (suggested by amotzg) involves installing a kernel module and does not appear to work on systems running OS X

  Read the article

• How do I fix error 1303 during TI Connect install?

  - by smoth190

  I recently purchased a TI-84 Plus graphing calculator, and I'm trying install the TI Connect software in order to connect the calculator to my computer via the USB cable. Unfortunately, I'm getting this error while trying to install the program: Error 1303. The installation has insufficient privileges to access this directory: E:\Data\Timothy\Documents\MyTIData. The installation cannot continue. Log on as administrator or contact your system administrator. However, my account is the only account on my PC, and it has administrative privileges. I've also tried running the installer with Run as Administrator, but with no luck. If I create the folder MyTIData manually, I receive this error: Error 1317. An error occurred while attempting to create the directory: E:\Data\Timothy\Documents\MyTIData I've reapplied the security settings to the E:\Data folder (and all its sub-directories) to Full for my account. I've also gone into Computer Management, and given SYSTEM full privileges for the entire disk. I've also logged out, logged back in, restarted, etc. but still, no luck. Now, I should mention that my Documents folder is not at the default location. I changed it due to my C: disk being a 90GB SSD, so I moved all my personal data onto the extra storage disk (which is ~1TB). I don't know if that is causing the issue, but it can't hurt throwing it out there. So why can't I install this program? Google'ing the problem brings up this error for various other installers (such as Visual Studio and Microsoft Office), but nothing for TI Connect. All the solutions are the same: Give the folder Full privileges...but I've already done this! I've also tried running the installer with and without the calculator plugged in, but it didn't change anything. In the prompt that contains the error, repeatedly clicking Retry or waiting a few moments before clicking Retry also produces no result.

  Read the article

• E-mail duplication problem

  - by Gavin Osborn

  I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

  Read the article

• Installing 64-bit Ubuntu Server 12.04 LTS, on a VM with VMWare Player, on a 64-bit Windows 7 PC

  - by WannaBeAGeek

  I'm trying to create a VM, using VMWare Player, with an ISO image of Ubuntu Server 12.04 (LTS). The machine I'm doing the installation on has an Intel(R) Core(TM) i5 CPU, and runs 64-bit Windows 7 I managed to create the VM (gave username, password, configured network etc), but I can't install Ubuntu Server. First I get this alert : Binary translation is incompatible with long mode on this platform. Disabling long mode. Without long mode support, the virtual machine will not be able to run 64-bit code. For more details see http://vmware.com/info?id=152. When I click OK, I get another alert : This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible. This host supports Intel VT-x, but Intel VT-x is disabled. Intel VT-x might be disabled if it has been disabled in the BIOS/firmware settings or the host has not been power-cycled since changing this setting. (1) Verify that the BIOS/firmware settings enable Intel VT-x and disable 'trusted execution.' (2) Power-cycle the host if either of these BIOS/firmware settings have been changed. (3) Power-cycle the host if you have not done so since installing VMware Player. (4) Update the host's BIOS/firmware to the latest version. For more detailed information, see http://vmware.com/info?id=152. Then, when I click OK, my VM exists, and I get back to the VMWare Player home screen. I don't know much about hardware and virtualisation, so there might be some necessary info I'm not giving. Please don't hesitate to let me know what is missing in my post, for finding solutions. Thanks :)

  Read the article

< Previous Page | 537 538 539 540 541 542 543 544 545 546 547 548  | Next Page >