Search Results

Search found 18677 results on 748 pages for 'current'.

Page 544/748 | < Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >

• Partition problem tyring to install window 7 starter

  - by ant2009

  Hello HP Mini 210 I am trying to install windows starter 7. Currently I have installed fedora 14 xfce. And I have allocated 24 GB NTFS for hard disk for the windows partition. My current partitions are as follows: /dev/sda2 97G 4.9G 91G 6% / tmpfs 494M 92K 494M 1% /dev/shm /dev/sda1 485M 68M 392M 15% /boot /dev/sda5 169G 26G 135G 16% /home I have created a boot USD to install windows starter 7. When the computer boots into the windows setup and I selected the partition I want to install windows on. I get the following message: "Setup was unable to create a new system partition or locate an existing system partition." This is setup displaying all my partitions: Disk 0 Partition 1 500MB 0 Primary Disk 0 Partition 2 97.7GB 0 Primary Disk 0 Partition 3 4GB 0 Primary Disk 0 Partition 4 171.3GB 0 Logical Disk 0 Partition 5 24.6GB 24.5 Logical <-- Trying install on this partition NTFS I have also tried to delete the partition in setup and create a new one. And also tried to format the partition. However, I still get the same error message. Many thanks for any advice,

  Read the article

• What are the replacement options for an IDE hd for a DOS based system?

  - by dummzeuch

  I have got a few "embedded" systems running MSDOS 6.2 which boot from and store data to IDE hard disks. Since these drives are nearing their end of life, the question arises how we can replace them. The requirements are: DOS must be able to install and boot from these drives. They must be able to sustain heavy (mostly) write access. If possible, they should be able to survive moderate vibrations (not too bad since the current hds have survived several years of that) I considered the following options so far: other ide hard drives: Unfortunately modern IDE drives are too large so DOS cannot boot from them even if I create small partitions. Older IDE drives are just that: old, so they are probably not the most reliable ones any more. SSDs: There are a few SSDs with IDE interface available. I have not yet tried them. Does anybody have any experience with them? They look like the ideal replacement provided that DOS can boot from them and that writing speed does not deteriorate too much (the old hds are no race cars either). Compact Flash: There are adapters for using CF with IDE controllers and they work fine. DOS can boot from them and they have no problems at all with vibrations. What I am not sure about is their durability. DOS uses FAT so some very few sectors are written every time the medium is being written to. IDE to SATA converters: I have no idea whether they are any good. Has anybody tried them? It might be an option to use one of these to connect an SATA SSD to the system. Are there any alternatives that I have missed? (We are working on replacing these systems, but it will still take a few years.)

  Read the article

• Reset sound volume in Windows 8

  - by Svish

  There seems to be a bug in Windows 8 causing the maximum volume to become lower than it really should be. I'm now at a stage where I put the volume up to max and the sound is still very low. I have a couple of Logitech Z-10 speakers with a display on them and when I touch the increase volume button on that it shows me the volume (but not able to increase it) is actually below middle even though Windows claims it to be maxed out. Is there any way I can reset the volume in Windows 8 so that I can get it up fully max again? A registry setting or something? Really don't want to have to reinstall windows or drivers or anything like that cause if it is a bug it'll probably happen again and I really don't want to have to do that every time this happens :p Any ideas? Manged to fix it by unplugging the usb connection to my speakers, turning the volume down on my computer and up on the speakers, and finally reconnecting the usb connection. Seems to have been an issue with the speakers and not Windows this time. BUT, I'm still curious how you can adjust/reset the Windows 8 sound volume without using the volume controls. Like, where is the value of the current volume setting(s) really stored? And can you manually adjust them?

  Read the article

• How to export and import an user profile from one Quassel core to another?

  - by Zertrin

  I have been using Quassel as my bouncer for IRC for quite a long time now. We (a group of administrators of a small network) have set up a shared Quassel core with many users on the same core. But now I would like to export everything related to my user account from the Quassel database on this core, in order to re-import it later in another Quassel core on my own server. Unfortunately, while a feature for adding users has been implemented into Quassel, nothing is so far provided for either exporting or deleting an user. (if deleting-a-user feature was available, I could have made a copy of the current database, delete all the other users leaving only mine, and use this resulting database on my own server, while leaving the first one untouched on the shared server) Despite extensive research on the Internet on this subject, I've found so far no solution. I have to precise that the backend database for the core has been migrated from the default SQLite backend to a PosgreSQL backend as the database grew sensibly (over 1,5 GB for now). However I'd be glad to hear from any working solution (SQLite or PostgreSQL backend) describing a way to export the data related to a specific user profile and then re-import-it in a new Quasselcore database.

  Read the article

• Copy Database Wizard fails on creation of view into another not-yet-copied database

  - by user22037

  Update - I found that doing a manual detach/reattach using MSDN article "How to: Move a Database Using Detach and Attach (Transact-SQL)" got around this issue. I'll just be creating a script to dettach and reattach but do the file copies manually. Any info on how to overcome the problems with the wizard would be helpful in the future. I am in the process of moving around 20 databases from our current server to a new one. When performing the copies however I have found that some databases can not copy if they have views into other databases that have not yet been copied to the target system. The log file generated says "failed with the following error: "Invalid object name" in reference to the database in the view. If I first copy just the database referenced in the view and then in a separate step copy the database over containing the view it is successful. However some other database have views into each other so can't just adjust the order in which the copy occurs. Is there any way to ignore this error and just allow everything to copy?

  Read the article

• 3 Monitor PCI-e Graphics card on Linux (without tremendous pain)?

  - by N Rahl

  As we are all painfully aware, the only way to get multiple monitors AND compositing (Compiz) on Linux is to use a single graphics card that can drive both (or in my case all three) screens. I bought a Radeon 5750 specifically because it claims to able to drive 3 monitors. I can plug in 3 monitors (2 DVI, 1 HDMI) and the Catalyst Control Center shows all 3, but only 2 can be enabled at a time. The exact message is: The current settings cannot be applied. Possible issues may include: - Display(s) cannot be enabled. - Setting(s) cannot be applied due to insufficient video memory. So I'm going to assume that either the 5750 doesn't support 3 monitors, OR, more likely, ATI couldn't be bothered to add that support to their Linux drivers. So this is a multipart question: First, can anyone suggest a PCI Express Graphics card that can run 3 screens on linux without tremendous pain? I'm looking for something where you install the driver and all three screens "just work". Does such a card exist? Second, if you have a 5750, have you been able to get it to do 3 monitors? I'm running Ubuntu 10.04 at the moment.

  Read the article

• Two network adapters in one WindowsXP PC, how to make them work?

  - by Deele

  I have a need to set up network so I can use two ethernet cards inside one Windows (Windows XP SP2) based PC, one for internet connection, second, for internal LAN. How should I configure each NIC, with what IP's, subnet masks and gateways, so I can use inernet on my PC and get in touch with devices on my LAN? I have found that there are some sort of re routing nessesary inside my PC, but how does it work? I have already set up some configuration already, but I can't use it together with PC #1 NIC #1 connected. I need to disconnect, to access NIC WEB interface. Current configuration: Switch #1 and PC #1 NAS #2 are gigabit one's, so I could access NAS with gigabit speed. PC #1 NIC #1 IP XX.XXX.162.106 SN 255.255.255.248 GW XX.XXX.162.105 PC #1 NIC #2 IP 10.0.0.1 SN 255.255.0.0 GW 0.0.0.0 NAS #1 NIC #1 IP 10.0.0.12 SN 255.255.0.0 GW 0.0.0.0 My question is - what exact configuration should I do for every NIC in this LAN, so it would work? Is it possible to achieve internet access for Laptop, that is inside that NIC #2 LAN (should I just set up basic ICS)?

  Read the article

• Slow, choppy video playback with nVidia 8600GT

  - by user5351

  I have an nVidia 8600GT card (made by EVGA) on a machine with Windows Vista (AMD Athlon X2 processors) and four gigs of ram. It runs pretty good, but I have had some slow/choppy/stuterring video playback issues whenever watching flash videos on Youtube or other sites. The problem is there with both Firefox and IE flash videos, but is maybe worse with Firefox. I also tried Linux with nVidia's binary drivers and it was about the same. I downloaded EVGA precision which allows me to control stuff like the fan and clock speed. The card's temp (in both Vista and Linux) is usually at 66C when idle (not playing a game or watching anything). It goes up a little when watching a video (maybe 68-72C). Any ideas on how to fix this? UPDATE: The issues are both with full screen and embedded flash videos. I have Flash 10.0.32.18 (always make sure I use most recent for security), and the CPU is an AMD Athlon 64 X2 Dual Core Processor 4000+ at 2.11 GHZ. The current GPU driver installed is the most recent GeForce one from last July.

  Read the article

• Gnome, open with, custom command, filename reference

  - by Tergiver

  I want to execute this custom command on a file from the Gnome File Browser: hexdump -C $f > $f.dump That would create a hexdump of the file with the file's name + .dump in the directory that the file exists in. When I say $f above I mean something that would substitute the name of the file that was opened. So I've tried "Open with", "Use a custom command". I can't get it to work. I've tried a number of symbols in place of $f. Is it even possible? Before you suggest getting a GUI hexdump program, this is just one example. I have the need to do this sort of thing for many terminal-type programs. Am I the only person on Earth who wishes for a hybrid File-Browser-slash-Command-Terminal? That would be a file browser which contained a terminal pane who's current directory always matched that of the file browser. One could execute shell commands in the context of what they were viewing in the browser.

  Read the article

• Advice for UPC/Surge Protector in home office

  - by Fred

  I'm just starting out as an independant developer, mostly Unix stuff with some Windows thrown in occasionally. I've been running two machines, a linux and a windows dev machine. Long story short, we had a bad storm come through last week and I unplugged one machine, forgot to unplug the other and the p/s and mobo ended up dead. Luckily I backup to an external service religiously (rsync.net for anyone interested), so there was no loss in data, but it did show me a glaring hole in my current setup, namely, lack of UPC and Surge Protection (this has honestly never been an issue before). Can anyone recommend a UPC/Surge Protector for a home office? It only needs to support a single machine (I opted to use vmware instead of rebuilding that machine), but it's a quad core Phenom 2 with a 1k watt p/s. This is outside my experience so I thought I'd get some input from others. I'm looking for something that's reasonably priced and does the job reasonably well. I don't need absolute 100% uptime, just something to protect my PC better than it is now.

  Read the article

• Apache APC (Windows) Can I optimize these APC settings more?

  - by ar099968

  I would like to optimize APC some more but I am not sure where I could do something. First here is the stats after 1 week of running with the current configuration: General Cache Information APC Version 3.1.9 PHP Version 5.4.4 APC Host XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Server Software Apache Shared Memory 1 Segment(s) with 128.0 MBytes (IPC shared memory, Windows Slim RWLOCK (native) locking) Start Time 2014/06/08 05:00:00 Uptime 6 days, 11 hours and 55 minutes File Upload Support 1 Host Status Diagrams Memory Usage Free: 99.7 MBytes (77.9%) Used: 28.3 MBytes (22.1%) Hits & Misses Hits: 510818 (99.9%) Misses: 608 (0.1%) Detailed Memory Usage and Fragmentation Fragmentation: 0.60% (609.8 KBytes out of 99.7 MBytes in 83 fragments) File Cache Information Cached Files 693 ( 35.4 MBytes) Hits 5143359 Misses 1087 Request Rate (hits, misses) 13.24 cache requests/second Hit Rate 13.24 cache requests/second Miss Rate 0.00 cache requests/second Insert Rate 0.01 cache requests/second Cache full count 0 User Cache Information Cached Variables 0 ( 0.0 Bytes) Hits 0 Misses 0 Request Rate (hits, misses) 0.00 cache requests/second Hit Rate 0.00 cache requests/second Miss Rate 0.00 cache requests/second Insert Rate 0.00 cache requests/second Cache full count 0 Runtime Settings apc.cache_by_default 1 apc.canonicalize 1 apc.coredump_unmap 0 apc.enable_cli 0 apc.enabled 1 apc.file_md5 0 apc.file_update_protection 2 apc.filters -/apc.php$, -/apc_clean.php$, -.tpl.cache.php$, -.tpl.php$, -.string.cache.php$, -.string.php$ apc.gc_ttl 3600 apc.include_once_override 0 apc.lazy_classes 0 apc.lazy_functions 0 apc.max_file_size 2M apc.num_files_hint 7000 apc.preload_path apc.report_autofilter 0 apc.rfc1867 0 apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.serializer default apc.shm_segments 1 apc.shm_size 128M apc.shm_strings_buffer 4M apc.slam_defense 0 apc.stat 1 apc.stat_ctime 0 apc.ttl 7200 apc.use_request_time 1 apc.user_entries_hint 4096 apc.user_ttl 7200 apc.write_lock 1

  Read the article

• Display errors using VMWare Player and Remote Desktop on Windows XP

  - by Tim

  I've come up against a weird display issue that I can't seem to find any "fix" for. When I first boot up my computer, everything behaves normally. If I start to use VMWare Player and/or Remote Desktop, my desktop starts having some odd video issues. The frames for some windows aren't drawn at all, if I move windows around rapidly, the area under where the window used to be isn't cleared (still shows artifacts of the content of the window), etc. In some cases, the minimize / restore / maximize buttons aren't drawn (but are click-able if you can guess where they are). I've tried the usual stuff - current drivers all around, using a single monitor, etc.. none of it seems to have any bearing. If I try to disable hardware acceleration, it tends to crash the computer. As I said earlier, it's running Windows XP, dual monitors, an NVidia en8400GS video card, asus p7p55d motherboard. Not sure what other pertinent details are needed. I would appreciate any help or suggestions!

  Read the article

• How to fix UNMOUNTABLE_BOOT_VOLUME (0x000000ED) on my Windows XP DELL laptop?

  - by Neil

  I have a Dell Latitude D410. Running Windows XP. I am receiving the STOP: 0x000000ED (0X899CF030,0XC0000185,0X00000000,0X00000000) Blue screen. Initially, I tried everything specified with the Microsoft KB articles. At this time, I was able to boot into the general safemode. I pulled the hard drive and was able to run chkdsk on it- it noted that it had fixed some errors, but I was still unable to boot. I put a brand new hard drive in the laptop. Windows XP installation worked up until the reboot, at which time the exact same error message came back up. What I have tried (all since the new hard drive was installed): chkdsk /R All suggested solutions in Microsoft KB articles Reseating RAM Opened laptop, reseated all connectors, looked for signs of damage (saw none) Reset BIOS options to default Ran the basic Dell diagnostics I have looked at the current entry:How can I boot XP after receiving stop error 0x000000ED - I am currently in the process of downloading the Ultimate Boot CD to use as a test, but I am not holding out a lot of hope as I really doubt this brand new Hard Drive is bad. Can anyone think of other areas I am missing? Ran MEMTEST86+ V4.10 for 15 passes (overnight). 0 Errors EDIT: FORMATTING

  Read the article

• Unable to install drivers of any kind of device on windows 8.1

  - by saadj55

  Windows 8.1 is unable to install drivers. First, I wanted to install Android ADB drivers for my Chinese Android Phone. I downloaded the relevant drivers from the manufacturers site and enabled USB debugging on my phone and tried to install it but Windows failed to find any drivers in the driver folder. After searching on google, I got to know that I will have to edit the win_usb.inf file in order to install the drivers so I did the editing part also. Added these line: %SingleAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C03 %CompositeAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C03 to both NTamd and NTx86 sections but the problem persists. Phone's current hardware id is: VID_0BB4&PID_0C03 I noticed that I need hardware ID with &MI_01 appended at the end. But Windows detects the device with the above hardware ID. I have the webcam drivers so I uninstalled WebCam Drivers to check if they can be installed back but I am also not able to install drivers for it. Windows is detecting the camera without that &MI_01 part. Please help. I cannot install webcam nor my android phone.

  Read the article

• Windows7: Howto force a "do you really want to shutdown?" dialog

  - by Vokuhila-Oliba

  Sometimes I wanted to choose "logout current user", but then I hit "Shutdown" by accident. Nearly everywhere else Windows7 is asking "do you really want to do this Yes/No". But that's not the case when I hit the "Shutdown" button. Windows7 shuts down immediately without giving me the chance to correct my mistake. Q1: So I am wondering why Windows7 shuts down immediately without asking "really do that?" in this case. Q2: Is there a way to change this behavior? E.g. Could I force Windows7 to display a dialog asking "Do you really want to shutdown ?". ADDED: I am running Windows7 Professional 64bit. ADDED: I tried to change this behavior with the policy editor. It seems to be very easy to completely remove the Shutdown button from the start menu. But I couldn't find an entry to turn on such a Yes/No dialog.

  Read the article

• SQL Server Replication Backup

  - by user18039

  Hi We have a new system that runs on SQL Server 2008 r2 64-bit. There is a primary on-line transactional processing (OLTP) database that accepts a high volume of updates from several thousand Point of Sale systems at stores around the country. In order to protect this vital function, I have decided to introduce a dedicated reporting database server - from which multiple users will run some pretty complex reports. I realise that there were a number of choices but I decided to use Transaction Replication as the mechanism for copying the data from the OLTP database to the new reporting database - one way replication. The solution has worked well in test. I'm now being asked what changes need to be made to the backup policy to cover the architectural changes. I have read pages such as MSDN:Strategies for Backing Up and Restoring Snapshot and Transactional Replication but I think these are overkill for my solution. In fact, my current thinking is that we simply need to continue making backups of the OLTP data and logs. If the Reporting db or any of the system replication (eg distribution) databases fail then it's no big deal - we can clear all down then re-create the replication. I realise that taking a complete snapshot of the OLTP would be time consuming (approx 5 hours) but I'd be more relaxed about this that trying to restore backups of the various data and log files in the correct sequence. My view is that the complex strategies set out in the MSDN article would only be the way to go for a more complex replication solution than I have, eg if there were multiple subscribers with 2-way replication. Would you agree? I'd be grateful for any advice. Many thanks, Rob.,

  Read the article

• Undo Google Sync in chrome

  - by iamcreasy

  I didn't know that my google account wasn't in sync with my chrome for the last couple of months and now that I have link again, the restored record is several months old. Now, that I've lost all my recent bookmarks and all other stuff...is there anything or anyway so I could revert the Google sync so I can get my bookmarks back? Update 1 I have found that under C:\Users\Profile_Name\AppData\Local\Google\Chrome\User Data\Default there is a file named Bookmarks.bak that holds the old state of my bookmarks before the sync. Update 2 Bookmarks is the file that holds the current(after sync) bookmark list. I replaced Bookmarks with Bookmarks.bak and restarted chrome, but still chrome isn't fetching information from the updated file. So, I have my old bookmark information, but how to restore it in chrome. Update 3 : solved I still couldn't figure out why replacing the bookmarks file didn't work and aparently that's the only solution available on web. I reinstalled everything and then copied the old bookmarks file. Then I got my bookmarks back again. Lession learned : Check regularly if google sync is working.

  Read the article

• How to back up initial state of external backup drive?

  - by intuited

  I've picked up an HP Simplesave external drive. It comes with some fancy software that is of no use to me because I don't use Windows. Like many current consumer-targeted backup drives, the backup software is actually contained on the drive itself. I'd like to save the drive's initial state so that I can restore it if I decide to sell it. The backup box itself is somewhat customized: in addition to the hard drive device, it presents a CDROM-like device on /dev/sr0. I gather that the purpose of this cdrom device is to bootstrap via Windows autoplay the backup application which lives on the disk itself. I wouldn't suppose any guarantees about how it does this, so it seems important to preserve the exact state of the disk. The drive is formatted with a single 500GB NTFS partition. My initial thought was to use dd to dump the disk (/dev/sdb) itself, but this proved impractical, as the resulting file was not sparse. This seemed to be because the NTFS empty space is not filled with zeroes, but with a repeating series of 16 bytes. I tried gzipping the output of dd. This reduced to the file to a manageable size — the first 18GB was compressed to 81MB, versus 47MB to tarball the contents of the mounted filesystem — but it was very slow on my admittedly somewhat derelict Pentium M processor. The time to do that first 18GB was about 30 minutes. So I've resorted to dumping the disk state and partition data separately. I've dumped the partition state with sfdisk -d /dev/sdb > sfdisk.-d.out I've also created a compressed image of the NTFS partition (the only one on the disk) with ntfsclone --save-image --output - /dev/sdb1 | gzip -c > ntfsclone.img.gz Is there anything else I should do to ensure that I can restore the precise original state of the drive?

  Read the article

• Is 1GB + 1GB RAM better than 2GB +0.5GB?

  - by pibboater

  My laptop has two slots for RAM, and currently has two 512 MB chips, for 1 GB. Windows XP is running terribly slow on it, so I want to upgrade the RAM. I could buy two 1 GB chips to replace both of the current 512 MB chips, to give me 2 GB of RAM. Or, the price is the same to buy one 2 GB chip, to replace just one of the 512 MB chips, and give me 2.5 GB total. The RAM it takes is PC2-4200 533MHz DDR2. What do you think would be better: buying two 1 GB chips so it can take advantage of dual-channel operation, or buying one 2 GB chip to end up with more total RAM but not dual-channel operation? Like I said, price is the same, so performance is the only consideration. I'm not doing anything especially intensive like video or photo editing -- just having multiple Office programs open, playing music, browsers, etc., but currently even opening the first application takes forever. If it matters, the laptop is a Toshiba Qosmio G25-AV513 running Windows XP Media Center SP3. Thanks! Kevin

  Read the article

• Windows 8 install from USB freezes

  - by Rafael Almeida

  I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

  Read the article

• Almost All Logical Volumes Disappeared - Recovery?

  - by Alex

  We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top.

  Read the article

• Linksys SFE2000 Interface

  - by boburob

  I have a real problem with a layer 3 Linksys switch. First, every time it looses power, it seems to reset back to an older config. Not only this, but when this happens it looses interface settings on one subnet. This would not be a problem but I am completely unable to get to the interface on the working side. It allows me to log on and then just displays a blank screen. I have tried this on: IE6 IE7 IE8 IE9 Firefox 3.5 Opera Chrome All with the same results, except for Opera, which loads half the interface but nothing I can really use. I really need to get onto this switch so I can sort out routing and VLAN tagged ports, so if anyone has any ideas on either of these issues please let me know ASAP! Thanks! Also, due to its location and my lack of laptops with serial connections I cannot putty into it. UPDATE: Looked into this a bit more and it looks like this model of switch does not save the current config to boot unless you make sure to save it yourself, which explains the first issue, however the broken interface is more worrying!

  Read the article

• Laptop Synaptics Touchpad No Longer Functional After Windows 7 Upgrade

  - by Chance

  I have a Toshiba laptop, with an integral Synaptics (PS/2 port) touch pad, that I bought pre-installed with 32-bit Windows Vista. After doing a clean install of 32-bit Windows 7, I can no longer get the touch pad to respond. The function (FN) keys on the laptop still operate correctly, but they no longer display on screen when used. I have no way of knowing if the function key to enable / disable the touch pad is working correctly, although the function keys for dim / brighten display, as well as others, work fine. I have removed the device from the device manager and allowed it to reinstall with no success. I have removed the previous drivers and updated them with the current 32-bit Win7 compatible versions from Synaptics website, with no success. The Synaptics icon displays in the taskbar, and the touch pad is available in the Device Manager, both of which say the device is installed and working correctly. I have checked to make sure that the touch pad is enabled in the Synaptics menu, and have tried toggling enabled / disabled with no success. If anyone has any suggestions, or knows where I can find a solution, I would be very appreciative.

  Read the article

• How do I setup a secondary incoming mail server?

  - by abrahamvegh

  I currently have a server running Debian 6, with postfix and dovecot handling email. This server hosts email for a number of domains and users, so I use MySQL as my backing store for users and forwardings and everything related. Currently, this server is the only server listed in an MX record for all of the domains it serves. I would like to create a secondary server that would be listed in the DNS with a lower priority (e.g. current primary server is priority 5, secondary would be priority 10), so that in the event that I need to reboot the primary server, or otherwise make it unavailable, the secondary server would receive email, and hold it until the primary server came back up, at which point it would deliver any held email to the primary server. I do not need the secondary server to function as a backup sending server. Users would never need to see the secondary server, they would simply not lose incoming emails if the primary server is down, and they would be unable to send or receive until the primary came back up. How would I go about doing this? I would like to use the same software if they can handle this task, because I’m already familiar with managing them.

  Read the article

• How do you permanently disable the 'This Connection is Untrusted' page on Firefox

  - by TheIronChef9

  I'm going insane. Can someone please help me to COMPLETELY DISABLE the 'This Connection is Untrusted' page on Firefox. Facts: I am running Firefox 23.0 on an Ubuntu machine (downloaded and installed ubuntu today) It is a work computer and I have to use my employer's proxy While visiting Webpages/webapps like Gmail or Google brings up the 'This Connection is Untrusted' page and I have to go through the whole tedious task of selecting 'I understand the Risks' and add Exceptions, etc. etc. The fact is, I don't care about the risks. I would rather this computer melt into the ground than have to see that page ever again. I want to dance naked in untrusted pages and not give a damn about the consequences. I just never want to see that page again. Ever. For some sites (eg. wikipedia), the css doesn't load and I end up seeing them in plain text. As a result these sites are completely useless. Wasted hours trying to solve this for stackoverflow.com. These issues happen on the Firefox on my Windows XP machine as well (also using the same proxy). I don't want to export/import certificates or create exceptions for every site that shows this bloody page. I just want this page gone. I don't want Firefox to tell me what's safe and what's not. Also, my system time and date are correct. I've also tried the lies on this page too with no good results. Edit: I've also tried the whole going into the Advance-Certificates-validation setup page and unchecked 'Use the Online Certificate Status Protocol (OCSP) to confirm the current validity of certificates' checkbox. Nothing happened even after restarting firefox or rebooting. I need help. Thanks.

  Read the article

< Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >