Search Results

Search found 17856 results on 715 pages for 'setup py'.

Page 553/715 | < Previous Page | 549 550 551 552 553 554 555 556 557 558 559 560  | Next Page >

• netlogon errors

  - by rorr

  I have two instances of mssql 2005 and am using CA XOSoft replication. The master is a failover cluster and the replica is a standalone server. They are all running Server 2003 sp2 x64. Same patch levels on all servers. This setup has worked great for several months until we recently restricted the RPC ports on both nodes of the master(5000 - 6000 using rpccfg.exe). We have to implement egress filtering, thus the limiting of the ports. We began receiving login errors for sql windows authentication and NETLOGON Event ID: 5719: This computer was not able to set up a secure session with a domain controller in domain due to the following: Not enough storage is available to process this command. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. We also see group policies failing to update and cluster file shares go offline at the same time. The RPC ports were set back to default when we started seeing these problems and the servers rebooted, but the problems persist. The domain controllers are not showing any errors. Running dcdiag and netdiag shows everything is fine. We have noticed that the XOSoft service ws_rep.exe is using a lot of handles(8 - 9k), about the same number that sqlserver is using. As soon as xosoft replication is stopped the login errors cease and everything functions correctly. I have opened a ticket with CA for XOSoft, but I'm not sure that the problem is actually xosoft, but that it is the one bringing the problem to light. I'm looking for tips on debugging RPC problems. Specifically on limiting the ports and then reverting the changes.

  Read the article

• Can I make two wireless routers communicate using the wireless?

  - by Dana Robinson

  I want to make a setup like this: cable modem <-cable- wireless router 1 <-wireless- wireless router 2 in another room <-cables- PCs in another room Basically, I want to extend my network access across the house and then have a bunch of network jacks available for my office PCs. Right now, I have a cable modem going to a wireless router in one room and a PC with a wireless PCI card in it in the office on the other side of the house. I use internet connection sharing with the other PCs in the office. The problem is that ICS is flaky, especially when I switch to VPN on the Windows box to access files at work. I picked up a wireless USB adapter that I thought I could share among the PCs I work on but I'm not very happy with it so I'm going to return it (NDISwrapper support for it is poor). Is this possible? My wireless experience so far has been pretty straightforward so I have no idea what kind of hardware is available. I've looked at network extenders but those just look like repeaters for signal strength. I want wired network jacks in my office.

  Read the article

• 1000Base-X layer 2/MAC address details

  - by user69971

  A layer 2 Ethernet frame is sent with a source and destination MAC address. Given a 100Base-TX (copper) trunk between two Cisco switches, I can do a "show interface fa 0/0" on S1 to see the MAC address assigned to the trunking interface, then go to Switch2 and do a "show mac address-table" and find the MAC address of the S1 fa 0/0 interface as a dynamically learned MAC in the table. Given a similar setup with a 1000Base-X (fiber GBIC) trunk, the MAC address shown in "show interface gi 0/0" on S1 does not show up in the MAC address-table of S2. Everything I can find online indicates that 1000Base-X uses largely the same layer 2 format as copper connections. There's some slight alterations - minimum frame size is slightly larger - but the fundamentals of the frame structure appear to be the same, including transmission with a source and destination L2 address. Why doesn't the address of gi 0/0 show up in the MAC address table of the connection switch? The only thing which seems to make sense would be that the GBIC has its own MAC address, almost as if its acting as a mini 2-port switch or hub, with the switch-assigned MAC address showing up on the interface connection and a different MAC address assigned to the fiber side. If this is the case, is there any way to see the GBIC MAC address on the switch? (I've tried to look up the details in IEEE 802.3z but it doesn't seem to be available without an IEEE membership or purchasing the standard. I find the base 802.3 PDFs for download, but not 802.3z.)

  Read the article

• Apache + mod_fcgid + perl = error 500

  - by f-aminov

  Hi guys! I'm trying to setup Apache2.2 with mod_fcgid and libapache2-mod-perl2 with no luck. I've created a fcgi-bin directory in the root directory of my website and put there a test.fcgi file with the following content: #!/usr/bin/perl use CGI; print "This is test.fcgi!\n"; While trying to access it via http://www.website.dom/fcgi-bin/test.fcgi I get error 500 (Internal Server Error). Here is my vhost config: <VirtualHost 95.131.29.226:8080> ServerName website.com DocumentRoot /var/www/data/website.com SuexecUserGroup user group ServerAlias www.website.com AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml <Directory "/var/www/data/website.com/fcgi-bin/"> Options +ExecCGI Allow from all Order allow,deny AddHandler fcgid-script .fcgi </Directory> </VirtualHost> fcgid.conf: <IfModule mod_fcgid.c> AddHandler fcgid-script .fcgi SocketPath /var/lib/apache2/fcgid/sock IdleTimeout 3600 ProcessLifeTime 7200 MaxProcessCount 8 DefaultMaxClassProcessCount 2 IPCConnectTimeout 8 IPCCommTimeout 60 </IfModule> SuExec log: [2010-04-06 03:02:47]: uid: (500/equ) gid: (502/equ) cmd: test.fcgi Apache error log: test! test! [Tue Apr 06 03:02:51 2010] [notice] mod_fcgid: process /var/www/data/website.com/fcgi-bin/test.fcgi(26267) exit(communication error), terminated by calling exit(), return code: 0 [Tue Apr 06 03:02:53 2010] [notice] mod_fcgid: process /var/www/data/website.com/fcgi-bin/test.fcgi(26261) exit(server exited), terminated by calling exit(), return code: 0 I've no clue why I'm getting error 500, but when I'm trying to access this file using console ($ perl /var/www/data/website.com/fcgin-bin/test.fcgi) everthing works fine without any errors... Any suggestions on how to solve this problem would be greatly appreciated. Thank you!

  Read the article

• DHCP not responding from laptop or router, but works on directly plugged PC?

  - by Matt H

  I'm at my sister in law's place in Singapore. I'm not from Singapore but am here for a few months. She has some sort of cable modem made by motorolla (SB5101 Surfboard). I think it goes, through starhub or similar provider. Anyhow, her PC is directly attached by cable (not wireless) and she can access the internet. There is no wireless router connected to it. The PC is configured with DHCP and appears to be working. However, the moment I unplug her PC and plug in my laptop, it doesn't get an address. The interesting thing here is that I also see this toredo tunnel adaptor etc. I'm not familiar with what that is. It appears to be being assigned an IP v6 address and an IP v4 address. I thought perhaps it's my laptop, but also when I plug in my DDWRT based router, it also fails to get a DHCP assigned address on the WAN port. I can't also seem to connect into any web configuration on the motorolla modem either. Any ideas? what kind of setup is this? all I'd like to do is plug in my wireless router so I can roam around the house and also access the internet.

  Read the article

• Sendmail Sends but never Delivers

  - by Jeremy

  I have tried 10 different emails hosted at Google, Yahoo!, GoDaddy, and some that are privately hosted, and each time I get the following errors. I have blocked sensitive information, but you will be able to see the errors. Feb 16 17:06:50 xxxxx sendmail[31824]: o1GM6ovJ031824: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30054, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (o1GM6oJo031825 Message accepted for delivery) Feb 16 16:54:19 xxxxx sendmail[31625]: o1GLsJPP031625: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30097, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (o1GLsJah031626 Message accepted for delivery) Feb 17 09:05:52 xxxxx sm-mta[10620]: o1H6Z3jM005734: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=07:30:49, xdelay=01:15:36, mailer=esmtp, pri=571331, relay=aspmx3.googlemail.com. [209.85.222.4], dsn=4.0.0, stat=Deferred: Connection timed out with aspmx3.googlemail.com. Feb 17 10:35:23 xxxxx sm-mta[12828]: o1HEZwn8011833: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=00:59:25, xdelay=00:12:36, mailer=esmtp, pri=300353, relay=aln-mailrelay.att.net. [12.102.252.75], dsn=4.0.0, stat=Deferred: Connection timed out with aln-mailrelay.att.net. If you take a look, they all send, but then (HOURS later) I get an error "stat=Deferred: Connection timed out with {server}". I'm at my wits end, because I use this same setup on each of my servers, and they all work.

  Read the article

• Domain authentication over OPEN wireless pre-logon (Windows 7 Pro) - No logon servers avail

  - by Shadow00Caster

  I have a plethora of laptops that are joined to an AD domain. I have an enterprise wireless system setup, the users of these laptops will be using an OPEN unsecured SSID which will ultimately have a captive portal that uses Radius-AD auth and firewall rules to allow access pre-captive portal auth to the proper ip's/ports of DC's etc for auth etc. I already have other laptops/users connecting to another SSID with 802.11x and SSO, all works perfectly pre-logon etc. My problem is with this open network, for some reason I cannot get the machines to auth to AD. The laptops connect to the wireless network, I confirm this on the controller and can ping the laptop at startup. I sharked the wires on the 2 DC's that these machines auth to, I can see a DNS SOA update from a laptop im testing with and can ping that test laptop from both DC's. When I try to logon, "There are currently no logon servers available to service the logon request." The shark shows no incoming connections to either DC even though the laptop is connected and pingable. Any help is greatly appreciated.

  Read the article

• How do I make dnsmasq serve IP addresses via IPoIB?

  - by Matt

  I have a cluster farm that I'm setting up. The nodes (computers in the farm) are connected via ethernet & IP over Infiniband. I'm needing to netboot the nodes and thought dnsmasq would fit well as it provides all the features including support for DHCP over IB and it works great for our ethernet setup. However, I can't seem to get it to provide IP addresses to the infiniband adaptors on the nodes. Each node is running an Ubuntu desktop 12.04 LTS. The dnsmasq server is running on ubuntu server 12.04LTS and has the following test config: dhcp-authoritative domain-needed bogus-priv expand-hosts no-hosts domain=local dhcp-range=eth0,10.0.0.10,10.0.0.255,12h dhcp-option=eth0,3,10.0.0.1 dhcp-range=ib0,10.1.1.10,10.1.1.255,12h dhcp-option=ib0,3,10.1.1.1 log-queries log-dhcp IPoIB works between nodes when configured statically but not with dhcp. On the nodes the file /etc/network/interfaces contains auto lo iface lo inet loopback auto ib0 iface ib0 inet dhcp #iface ib0 inet static #address 10.1.1.5 #netmask 255.0.0.0 up echo connected >`find /sys -name mode | grep ib0` Is there something I need to do on the client or server end to make this work?

  Read the article

• Biztalk 2009 logshipping with SQL 2008

  - by Manjot

  Hi, I am setting up biztalk logshipping for Biztalk 2009 database. Following http://msdn.microsoft.com/en-us/library/aa560961.aspx article, I am doing the following to setup biztalk logshipping on destination server: Enable Ad-hoc queries by: sp_configure 'show advanced options',1 go reconfigure go sp_configure 'Ad Hoc Distributed Queries',1 go reconfigure go sp_configure 'show advanced options',0 go reconfigure go Execute LogShipping_Destination_Schema & LogShipping_Destination_Logic in master on destinations server Run: exec bts_ConfigureBizTalkLogShipping @nvcDescription = '', @nvcMgmtDatabaseName = '', @nvcMgmtServerName = '', @SourceServerName = null, -- null indicates that this destination server restores all databases @fLinkServers = 1 -- 1 automatically links the server to the management database When I run this I am receiving the following error: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. After some research I found some info : Usually this error means that the SQL Server Service Principal Name (SPN) was not configured, and NTLM was not being used as an authentication mechanism. SQl services are runing under different domain accounts. So, I asked the domain admin to create SPNs for the servers, SQL service accounts for beoth source and destination using name and FQDN. enabled computer name and service accounts for delegation. When I run the following: select * from sys.dm_exec_connections I get the the same error: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON' Any help please?

  Read the article

• Cisco ASA and static IPv6 tunnel endpoint?

  - by Martijn Heemels

  I recently installed a Cisco ASA 5505 firewall on the edge of our LAN. The setup is simple: Internet <-- ASA <-- LAN I would like provide the hosts in the LAN with IPv6 connectivity by setting up a 6in4 tunnel to SixXS. It would be nice to have the ASA as tunnel endpoint so it can firewall both IPv4 and IPv6 traffic. Unfortunately the ASA apparently can't create a tunnel itself, and can't port-forward protocol 41 traffic, so I believe I would have to do one of the following instead: Set up a host with it's own IP outside the firewall, and have that function as tunnel-endpoint. The ASA can then firewall and route the v6 subnet to the LAN. Set up a host inside the firewall that functions as endpoint, separated via vlan or whatever, and loop the traffic back into the ASA where it can be firewalled and routed. This seems contrived, but would allow me to use a VM instead of a physical machine as endpoint. Any other way? What would you suggest is the optimal way to set this up? P.S. I do have a spare public IP address available if needed, and can spin up another VM in our VMware infrastructure.

  Read the article

• OS X can't copy files from Windows Home Server...over wifi.

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks!

  Read the article

• Mouse click-focus wanders in vmPlayer 3.0 dual-monitor

  - by Gary M. Mugford

  Previously, a WinXPSP3 session running on a WinXPSP3 host computer ran perfectly fine in a dual monitor setup. No issues with vmPlayer 2.x. BEFORE updating to vmPlayer 3, the following problem cropped up. When clicking in a single monitor, you would get exactly what you expected. However, when the display was stretched across two monitors, the clicking would be to the left of the mouse cursor. The farther RIGHT you were, the farther left the click would occur. In other words, if you clicked on the system menu of a window in the upper left of a window on the left monitor, you would get the system menu. Move half a screen to your right and the click would be on an item about a quarter of the way over, rather than where you were clicking. And by going all the way to the far right of the right monitor, you could bring up a right-click menu on the far right of the LEFT monitor. I Hope I have described this properly. It's confusing, even in words. In single monitor mode, everything works perfectly fine. If, instead of using either UltraMon or DisplayFusion, you run a single desktop across both monitors (3200x1600), there are no mousing issues. Unfortunately, having two 1600x1200 monitors, that depth of 1600 makes that hack less than useable. My graphic card won't offer anything resembling 3200x1200. vmPlayer 3.0 did not alleviate the situation. The microsoft mouse drivers are up to date and so are the nVidia card drivers. Any ideas?

  Read the article

• What benchmark tool to use to benchmark hardware for VM server?

  - by Mark0978

  We are setting up a new piece of hardware to virtualize several of our servers on. Choices are RAID 5, RAID 6, and RAID 0+1. We are wanting to benchmark all three before we go live with the machine, but I'm not sure how to test the speed. Since we will be using it to host VMs, what will the actual disk traffic look like? What can I use to see if RAID 6 is too slow? Short of setting up the system with all the VM's on it and running that way, then redoing on all the work, I'm not sure how to test it. It them becomes more of a subjective test than an objective one. I'm worried that RAID6 will have too much overhead, that RAID5 will be to fragile with 3TB drives and I've never worked with 0+1 at all. So in short I'd like to setup the base machine (which will be running Linux) and then test the underlying SW RAID for speed. What kind of tool exists to simulate this kind of load? Barring the lack of a specific tool, how about a generic FS testing tool that will simulate different loads?

  Read the article

• LCD monitor flicker when connected to a laptop using VGA

  - by Björn Lindqvist

  I have a dual screen setup with two AOC e2450Sw monitors connected to a laptop. The laptop has one HDMI and one VGA output. When one of the monitors is connected using VGA, it flickers or displays static noise. The flickering is fairly subtle and only visible on darker colors. But it is there and noticable and appears like horizontal lines. The problem only appears on the monitor connected to the laptop using the VGA cable. If I swap the monitors, the one connected using VGA is displaying the flicker but not the one connected using HDMI. The simple solution would ofcourse be to connect both monitors using HDMI, but since the laptop only has one VGA and one HDMI out that isn't possible. I've tried tweaking the monitor setting using the OSD menu, but it had little or no effect. Update: After several more trouble shooting hours, it seems the problem is not related to the monitor or VGA cable as the problem persists even if I swap the display with another brand and different cables. So it may be the graphics card? Intel HD Graphics 4000. The laptop is Acer Aspire E1-571.

  Read the article

• Lightweight Linux distro that includes developer tools? (or, the most BSD-like Linux)

  - by RevAaron

  I cut my teeth on Minix and Slackware 1.1, but I've been in the OS X Wilderness for the last few years. I'm trying to standardize on a Linux distribution for personal and work-related use on less powerful laptops and under virtualization. So far, NetBSD and OpenBSD are the best fit for my purposes- but after plenty of frustration I've come to the conclusion that I need to stick with Linux to get the hardware and software support that comes with it. What I like about NetBSD/OpenBSD that I'd like to keep: X, but no default KDE, GNOME or XFCE! A sensible /etc and dot file setup- startx calls xinit, xinit looks for ~/.xinitrc; nothing more complicated than that is needed. Command line tools and file-based configuration: I shouldn't need a GUI to connect to a WAP. Decent selection of binary packages; building from source is OK, but nothing source-only like Gentoo. pkg_add (BSD) and apt-get both have treated me well in the past. Modest RAM and HDD requirements: boot + X + awesome+ two xterms takes up 80 MB on OpenBSD and 240 MB on Debian 5 and Crunchbang In my experience, most "lightweight" and Live CDs focus on a nice desktop environment crammed into a CD or USB stick; once you add build-essentials you end up with something just about as bloated as Ubuntu or Debian full install. Crunchbang is a great example. Thanks in advance for all suggestions!

  Read the article

• Ubuntu 10.04 Keyboard and Mouse Freezing Problem

  - by nitbuntu

  I had a partition setup with Windows XP and Ubuntu 8.04 dual booting. I recently upgraded to Ubuntu 10.04 by installing fresh from CD but leaving the previous /home folder as is. Things seemed to be working fine, but started finding that my mouse and keyboard were freezing. After a quick search on the internet, I found the following suggestions as shown here:- Ubuntu Forums Here the suggestion was to:- Edit /etc/default/grub, go to the line that begins like: GRUB_CMDLINE_LINUX_DEFAULT= Change it to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi=off" After that, run this command: sudo update-grub and Reboot This seemed to have resolved the issue but after a couple of days I again find my mouse and keyboard freezing. I also find that my parallel port printer had also stopped working. I have saved the output of dmesg and my syslog. The first can be viewed here but the syslog had too many characters, so if someone can suggest an alternative to freetexthost, I can post it there. Moreover, if there is any other information that should be provided, do let me know. I do hope we can get to the bottom of this issue. Thank you in advance for any help that could be provided.

  Read the article

• Active Directory FRS problems. 13508 error and other problems

  - by ITPIP

  I have 3 Domain Controllers. We will call them DC1, DC2 and DC3. DC3 and DC2 show Event ID 13508 in their FRS logs with no follow-up event(13509 I think) to say the error had been fixed. DC1's FRS log no matter what you do never shows any events besides FRS service stopped and started. DC1 holds the SYSVOL that needs to be replicated to the other DC's. The other DC's sysvol folders are empty. I have tried the burflag method of fixing this but I haven't had any luck. My procedure for that was to stop all FRS services on all DC's. Then set the burflag on DC1 to D4 and the other two DCs burflag to D2. Started FRS on DC1 and the only event's I see in DC1's FRS event logs are service stopped and service started messages. This fact is leading me to believe that something is wrong on FRS for DC1. I believe there should be events 13553 and 13516 in the FRS event logs after an authoritative sysvol restore. The other two DC's do not have anything in their SYSVOL, otherwise I would have made one of them the authoritative sysvol. DC1 is MS Server 2003 Enterprise Edition SP2 DC2 is MS Server 2003 Standard Edition SP1 DC3 is MS Server 2003 R2 Standard Edition SP2 I did not setup this domain originally but I am now the administrator of it, so I don't have a lot of background on why certain things may have been done in the past. My main goal is to try and fix these issues to get myself better prepared to decommision DC1 and add a DC running Server 2008 to my domain. Thanks.

  Read the article

• HP c6180 driver refuses to install - "must reboot to continue delete files and continue install" loo

  - by Aszurom

  User called me last night, can't get HP drivers to install for printer. 500 meg download for latest c6180 driver. PC says "computer must be restarted to delete some files, then setup will continue." and it won't pass that point. (that's not exact phrasing of the error, and I'm not on the system now) Target machine is XP SP2. I upgraded to SP3. Fully patched. Ran malwarebytes, spybot, hijack this and turned off all startup entries. I noted that windows update also failed on optional printer driver updates for other printers installed on the machine. Went to printer server properties, removed all print drivers from system, deleted all printer ports. Made sure no services were marked disabled. After 5 hours of fighting this I started to get desperate, and uninstalled anything that referenced HP in the machine at all. Still no cure. I'm 6 hours into this and completely stumped. Google returns nothing applicable except unanswered requests for help on same topic.

  Read the article

• nginx inserting extra characters in Multi-status reply body

  - by user125011

  Here's the setup. I've got one server running apache/php hosting ownCloud. Among other things, I'm using to do CardDAV contact syncing. In order to make things work with my domain I have an nginx server running on the frontend as a reverse-proxy to the ownCloud server. My nginx config is as follows: server { listen 80; server_name cloud.mydomain.com; location / { proxy_set_header X-Forwarded-Host cloud.mydomain.com; proxy_set_header X-Forwarded-Proto http; proxy_set_header X-Forwarded-For $remote_addr; client_max_body_size 0; proxy_redirect off; proxy_pass http://server; } } The problem is that when my phone does a PROPFIND on the server, nginx adds extra characters to the content body that throw the phone off. Specifically, it prepends d611\r\n at the front of the body and appends 0\r\n\r\n to the end of the content. (I got this from wireshark.) It also re-chunks the result. How do I get nginx to send the original content as-is?

  Read the article

• Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace

  - by Nick

  I have an laptop top hard drive I was trying to use to my new media computer. The case is small and can accommodate for 2 2.5" drives, no 3.5" drives. I had been using the hard drive as storage hard drive until now. When I go to install Windows on the hard drive first I'm prompted at the bios of: Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace. And then again in the Windows Setup, informing me that the hard drive is bad. So I did a full format of the drive and tried again. Same error. So I took it out and hooked it back up to my other computer via an Sata usb adapter kit (maybe the cause?). The hard drive is recognized fine and when I scanned it for errors by going: right click -> properties -> tools -> error checking It returns that the hard drive is fine. I have tried 3 different SATA cables and multiple jumpers. When I plugged in my 1.5 tb 3.5" drive the computer that gives me the S.M.A.R.T. error on the 2.5" drive, recognizes it with no problems. Any ideas on why this is happening and how I can fix it?

  Read the article

• Joining Samba to Active Directory with local user authentication

  - by Ansel Pol

  I apologise that this is somewhat incoherent, but hopefully someone will be able to make enough sense of this to understand what I'm trying to achieve and provide pointers. I have a machine with two network interfaces connected to two different networks (one of which it's providing several other services for, such as DNS), running two separate instances of Samba, one bound to each interface. One of the instances is just a workgroup-style setup using share-level authentication, which is all working fine. The problem is that I'm looking to join the other instance to an MS Active Directory domain (provided by MS Windows Small Business Server 2003) to enable a subset of the domain users to access the shares from Windows machines on the other network. The users who need access from the domain environment have accounts (whose names are all-lowercase versions of their domain usernames) on the machine running Samba, but I'm not sure about how to map the UIDs and everything I've read concerns authenticating accounts on that machine against either AD or another LDAP server. To clarify: I only want the credentials for AD users accessing the non-workgroup Samba instance to be authenticated against AD, not the accounts on the machine running Samba. I hope this is sufficiently clear. EDIT: In addition to being able to access the Samba shares from AD, I do also need to be able to access a share on the domain from the machine running Samba but would still like everything non-Samba-related to authenticate locally.

  Read the article

• 4.00gb (3.25gb usable) in Windows 7 x64

  - by dotnetdev

  Hi, I have setup Windows 7 Ultimate x64 on my PC. I have 4gb RAM and my BIOS states the correct amount (4096mb), but I cannot Windows (System Manager) says I have 4.00gb (3.25gb usable). This seems to be a popular issue, and I have looked for an integrated video card (integrated with my chipset) to disable but haven't found anything. What else can be preventing me from seeing all 4gb? When I had Vista 32bit, it would say 3.25gb RAM not 4.00gb (3.25gb usable). I have an x64 CPU and when I brought my RAM, I used a compatibility tool from Crucial (the memory vendor) to test how much memory my PC can support and 4gb was the answer (this was a windows app I think). Chipset is Intel(R) G33/G31/P35/P31 Express Chipset PCI Express In the bios, I looked for an onboard video card (integrated) and there was no such thing, but a couple of other onboard devices. There are also no "Resource Mappings" settings. FURHTER DETAILS: Chipset North Bridge: Intel Bearlake G33 South Bridge: Intel 82801IR ICH9R Maximum Memory Amount 8 GB Graphics Controller Type Intel GMA 3100 (Enabled) I guess the first thing is, how do I disable the graphics controller? EDIT: This thread (http://forums.legitreviews.com/about23417.html) indicates the issue is with memory mapped devices, but someone on this thread says that does not apply to x64. The rest of the comments points to a mobo issue for the guy who started that thread. Thanks

  Read the article

• SSH over HTTPS with proxytunnel and nginx

  - by Thermionix

  I'm trying to setup an ssh over https connection using nginx. I haven't found any working examples, so any help would be appreciated! ~$ cat .ssh/config Host example.net Hostname example.net ProtocolKeepAlives 30 DynamicForward 8118 ProxyCommand /usr/bin/proxytunnel -p ssh.example.net:443 -d localhost:22 -E -v -H "User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32)" ~$ ssh [email protected] Local proxy ssh.example.net resolves to 115.xxx.xxx.xxx Connected to ssh.example.net:443 (local proxy) Tunneling to localhost:22 (destination) Communication with local proxy: -> CONNECT localhost:22 HTTP/1.0 -> Proxy-Connection: Keep-Alive -> User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32) <- <html> <- <head><title>400 Bad Request</title></head> <- <body bgcolor="white"> <- <center><h1>400 Bad Request</h1></center> <- <hr><center>nginx/1.0.5</center> <- </body> <- </html> analyze_HTTP: readline failed: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host Nginx config on the server; ~$ cat /etc/nginx/sites-enabled/ssh upstream tunnel { server localhost:22; } server { listen 443; server_name ssh.example.net; location / { proxy_pass http://tunnel; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } ssl on; ssl_certificate /etc/ssl/certs/server.cer; ssl_certificate_key /etc/ssl/private/server.key; } ~$ tail /var/log/nginx/access.log 203.xxx.xxx.xxx - - [08/Feb/2012:15:17:39 +1100] "CONNECT localhost:22 HTTP/1.0" 400 173 "-" "-"

  Read the article

• Huh? JDK not found? (on Windows 7 64-bit)

  - by Android Eve

  I am setting up a development environment for the latest Android 2.3 on a fresh install of Windows 7 64-bit. I first installed the 64-bit JDK 6 (jdk-6u23-windows-x64.exe). Then, I installed 64-bit Eclipse Classic 3.6 (eclipse-SDK-3.6.1-win32-x86_64.zip). Then, I proceed to install the Android SDK Starter Package: installer_r08-windows.exe. But... upon start it says: "Java SE Development Kit (JDK) not found." Why? I just installed it. Is this a mismatch between 32-bit and 64-bit? How do I solve this? Update (1): I tried setting the %JAVA_HOME% environment variable, as well as setting the Installed JREs in Eclipse, as suggested below. None of these solved the problem. It appears that I am not the only experiencing the problem, as this thread suggests: http://stackoverflow.com/questions/1919340/android-sdk-setup-under-windows-7-pro-64-bit I wonder whether there is a 64-bit version of the Android SDK. Update (2): I used the zip version instead (android-sdk_r08-windows.zip), ran android.bat, updated all SDK packages, and installed the ADT plugin (8.0.1), not before having to check: 'Contact all update sites during install to find required software'. We'll see how this goes... Update (3): It worked! (going to accept @bubu's answer shortly) -- but why doesn't the emulator include the HelloAndroid app when I run it (Ctrl+F11) from Eclipse?

  Read the article

• connect server to server on secondary NIC

  - by microchasm

  Hi, I have a CentOS box with multiple NIC's running Apache. I also have another box running RHEL that will be the MySQL server. I'm trying to use the secondary NIC on the Apache box to connect directly to the MySQL server, but so far no luck. I want to isolate the MySQL box as much as possible which is why I'm going for a direct connection as opposed to running through a switch. I have a crossover cable running between them. IP configs: Apache box eth0 [to lan] ip addr: 192.168.200.100 netmask: 255.255.0.0 gateway: 192.168.111.1 eth1 [to mysql] ip addr: 192.168.200.101 netmask: 255.255.0.0 gateway: [blank] MySQL box eth0 [to apache] ip addr: 192.168.200.203 netmask: 255.255.0.0 gateway: 192.168.200.201 The rest of our network is on 192.168.111.0/24 subnet. Ping only returns Destination Host Unreachable. I've tried various variations of this setup (including straight through cable), and I can't seem to get them to talk to each other. Any help appreciated.

  Read the article

< Previous Page | 549 550 551 552 553 554 555 556 557 558 559 560  | Next Page >