Search Results

Search found 38064 results on 1523 pages for 'oracle linux'.

Page 555/1523 | < Previous Page | 551 552 553 554 555 556 557 558 559 560 561 562  | Next Page >

• How to completely disable IPv6 for loopback interface on RHEL 5.6

  - by Marc D

  I've done lots of research on how to disable IPv6 on RedHat Linux and I have it almost completely disabled. However the loopback interface is still getting an inet6 loopback address (::1/128). I can't find where IPV6 is still enabled for loopback. To disable IPV6 I added the following settings to /etc/sysctl.conf: net.ipv6.conf.default.disable_ipv6=1 net.ipv6.conf.all.disable_ipv6=1 And also added the following line to /etc/sysconfig/network: NETWORKING_IPV6=no After rebooting, the inet6 address is gone from my physical interface (eth0), but is still there for lo: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:50:56:xx:xx:xx brd ff:ff:ff:ff:ff:ff inet 10.x.x.x/21 brd 10.x.x.x scope global eth0 If I manually remove the IPV6 address from loopback and then bounce the interface, it comes back: # ip addr del ::1/128 dev lo # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo # ip link set lo down # ip link set lo up # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I believe IPV6 should be disabled at the kernel level as confirmed by sysctl: # sysctl net.ipv6.conf.lo.disable_ipv6 net.ipv6.conf.lo.disable_ipv6 = 1 Any ideas on what else would cause the loopback interface to get an IPV6 address?

  Read the article

• Installing sphinx on a web hosting server

  - by fiftyeight

  I want to install sphinx search on a web-hosting server. I'm on a Linux VPS with hostgator, but I never actually installed anything on a remote server so this will be a first time for me. If there's anyone here who installed sphinx it's really help me I had some problems when using sphinx on my PC with the permissions and the MySQL files, eventually I got it working on my PC. Anyway, I'd me really grateful if anyone can help me with some questions Do i need root access to install sphinx? I have root access to the server but I'd connect to it as a normal user since doing stuff as root is always less secure. can anyone tell me by what user I need to execute the indexer and the search daemon? Should I use root access in order to this? when I did it as a normal user on my PC it gave me some trouble with the PID file and the log files. last time I executed the search deamon I executed it as a normal user and it gave me some trouble, I created the folder /var/log/ for log files and did chmod 777 on it, but still when I executed the search daemon it created the PID file "searchd.pid" file but with no permissions for some reason, any idea why? Thanx in advance. fiftyeight

  Read the article

• Plesk FTP not working but SFTP and Shell is working

  - by shamittomar

  I am facing a strange problem. The FTP on my Plesk VPS is not working. Whenever I try to connect, FileZilla FTP client says: Status: Resolving address of xxxxxxxxxxxxx.com Status: Connecting to xxx.xxx.xxx.xxx:21... Status: Connection established, waiting for welcome message... Error: Could not connect to server So, it's not even going to the step of asking username/password. So, it's something else. The SFTP on port 22 is working fine. Also, I can successfully do shell access and run commands. But, I NEED FTP access too on port 21. I have searched everywhere but can not find any setting to enable it. This is the Plesk version info: Parallels Plesk Panel version 9.5.2 Operating system Linux 2.6.26.8-57.fc8 CPU GenuineIntel, Intel(R) Pentium(R) 4 CPU 3.00GHz Any help is appreciated. [EDIT]: The firewall is not blocking it. I have checked it on server and there are absolutely no blocking rule. Firewall states: All incoming/outgoing connections are accepted on FTP And on client-side (my PC), I can connect to other FTP servers so this is not an issue in my PC's firewall. Moreover, I can not even connect to the FTP from online FTP clients like net2ftp.

  Read the article

• Ping with explicit next-hop selection (aka Monitoring multiple default gateways)

  - by Michuelnik

  I have a linux (debian) router with two internet connections (A) and (B). (A) is preferred, (B) is fallback. I want to monitor the internet connection (and not only the availability of the gateways!) and change the default route appropriately. If (A) is not providing internet, switch to (B) If (A) is providing internet again, switch back to (A). Only problem I have is in case (2). My routing table points towards a working internet so I cannot easily detect whether internet is working over link (A) again. I am search for a ping or traceroute (or other diagnosis-tool) which can select the next-hop explicitly. ping -r looks promising, but can only ping a host on the lan. (It only has to write another destination address in the packet, damnit!) traceroute -g gateway looks even more promising and nearly does what I want - but sets source routing options which my next-hops deny. (Not within my administrative boundary...) I just want a $ping, that can: select a source interface (and address) select a next-hop on that interface ping any arbitrary ip address I could do evil trickery with policy-based routing but that would have production impact for all users. I would like to see a side-effect-free solution....

  Read the article

• Trouble getting started with the STEALTH monitoring package

  - by dlanced

  Is anyone here familiar with the Linux-based STEALTH package (for monitoring FS integrity of client systems)? I'm trying to get started with a very simple configuration, but I'm running into trouble (this is running under Ubuntu 14.04): Config line `USE BASE/root/stealth/10.0.0.79' invalid STEALTH (2.11.02) started at Fri, 30 May 2014 15:25:00 +0000 Program terminated due to non-zero exit value for -type f -exec /usr/bin/sha1sum {} \; (EOC Fri May 30 15:25:00 2014 127) Stealth is creating a binary tmp file in the Stealth server root and generating a "report" file in the start directory, but not much else. Regarding the "USE BASE...invalid" error, and just to be sure, I manually created the directories in /root, but it didn't help. And, by the way, I am running stealth with sudo. Everything seems to be configured correctly: I'm able to ssh into root@client from the stealth machine without a password Here's my "policy" file (I've removed the email directives just for simplicity): DEFINE SSHCMD /usr/bin/ssh [email protected] -T -q exec /bin/bash --noprofile DEFINE EXECSHA1 -xdev -perm +u+s,g+s ( -user root -or -group root ) \ -type f -exec /usr/bin/sha1sum {} \; USE BASE/root/stealth/10.0.0.79 USE SSH ${SSHCMD} USE DD /bin/dd USE DIFF /usr/bin/diff USE PIDFILE /var/run/stealth- USE REPORT report USE SH /bin/sh GET /usr/bin/sha1sum /root/tmp LABEL \nchecking the client's /usr/bin/find program CHECK LOG = remote/binfind /usr/bin/sha1sum /usr/bin/find LABEL \nsuid/sgid/executable files uid or gid root on the / partition CHECK LOG = remote/setuidgid /usr/bin/find / ${EXECSHA1} LABEL \nconfiguration files under /etc CHECK LOG = remote/etcfiles \ /usr/bin/find /etc -type f -not -perm /6111 \ -not -regex "/etc/(adjtime\|mtab)"\ -exec /usr/bin/sha1sum {} \; Any ideas? Thanks,

  Read the article

• Allowing access to company files accross the internet

  - by Renaud Bompuis

  The premise I've been tasked with finding a solution to the following scenario: our main file server is a Linux machine. on the LAN, users simply access the files using SMB. each user has an account on the file server and his/her own access rights. user accounts are simple passwd/group security accounts, not NIS/LDAP. The problem We want to give users (or at least some of them, say if they belong to a particular group) the ability to access the files from the Internet while travelling. Ideally I'd like a seamless solution. Maybe something that allows the user to access a mapped drive would be ideal. A web-oriented solution is also good but it should present files in a way that is familiar to users, in an explorer-like fashion for instance. Security is a must of course, and users would be expected to log-in. The connection to the server should also be encrypted. Anyone has some pointers to neat solutions? Any experiences? Edit The client machines are Windows only.

  Read the article

• Strange issue with 74.125.79.118

  - by Domenic

  I'm facing with a strange issue on a Linux server. After frequent crashes the analysis found that the server is led to collapse by a huge number of connections to the ip 74.125.79.118 departing from php scripts of the hosted web sites. After a depth analysis of the files I'm found that are not present any malware infections. Ip 74.125.79.118 is Google. I realize after a Google search that the connections to this ip are generated by embedded video from youtube on web sites, among other Google features like safe search. But I don't understand how this type of behavior can lead to the collapse the server and the uniqueness of the situation leads me to think that the situation is far from being attributable only to Google and Youtube. Also I've found that blocking connections from eth0 to 74.125.79.118:80 doesn't solve the issue but if I stop DNS traffic from eth0 to internet, connections to 74.125.79.118 stops. I'm really confused about this. Any suggestions? Cheers.

  Read the article

• Software RAID 1 Configuration

  - by Corve

  I have created a software RAID 1 quite some while ago and it always seemed to work for me. However I am not completely sure that I have configured everything right and do not have the experience to check so I would be very grateful for some advice or just verification that all seems right so far. I am using Linux Fedora 20 (32 bit with plans to upgrade to 64bit) The RAID 1 should consist of two 1TB SATA hard drives. This is the output of mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sun Jan 29 11:25:18 2012 Raid Level : raid1 Array Size : 976761424 (931.51 GiB 1000.20 GB) Used Dev Size : 976761424 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Sat Jun 7 10:38:09 2014 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : argo:0 (local to host argo) UUID : 1596d0a1:5806e590:c56d0b27:765e3220 Events : 996387 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 0 1 active sync /dev/sda The RAID is mounted successfully: friedrich@argo:~ ? sudo mount -l | grep md0 /dev/md0 on /mnt/raid type ext4 (rw,relatime,data=ordered) Basically my question are: Why do I only have 1 active device? What does the State removed at bottom mean? Also I noticed some strange error messages that I see on the console on system start and shutdown and always repeating in the background when I switch with Ctrl + Alt + F2: ... ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: COMRESET failed (errno=-32) ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ... Are these errors related to the RAID? Something seems wrong with the SATA devices.. All together the system works (I can read and write to the mounted raid) but I always had these strange errors on startup shutdown (probably always in the background). Thx for your help

  Read the article

• Family server setup

  - by Manny

  Hi all, I really hope some of you can give me some direction. I have setup a linux server at home and through samba I can access files from different computers in my home. I would like to use this server as a file-server for my family (brothers, sisters and parents who all live in their own homes). I really like the way it is set up right now with user and permission controls, but I've read that it is bad idea to open up the samba port to the world. The requirements are simple: 1) it should be easy to access, by using standard web browsers or mounting the drive (shouldn't have to use any VPN setup or use putty etc) 2) should be somewhat secure. We just want to share family pictures instead of putting them on facebook or picasa or other web server, nothing top secret. Here is what I've looked into: 1)Webdav. It seems decent but seems like it windows7 doesn't like it very much, even with digest mode authentication. User controls and permissions are not as flexible as samba (or at least to my knowledge). I really like the user and group permissions in samba, but if I could live with webdav if it worked seamlessly with windows, it should just work shouldn't it? 2) I read somewhere to stay away from ftp as it is outdated and that there are newer and better internet file-server setups? Was that a reference to webdav? I am so confused, please help... Manny

  Read the article

• how do I fix a wrong UUID in grub.cfg?

  - by mozerella

  I run Debian Wheezy alone on my PC and I recently copied the root partition to another with rsync as I found that worked well (I also know about dd and ddrescue but they leave unusable space on the new partition). I generated a new random UUID for the new partition with sudo tune2fs -U random /dev/hda9 and also updated fstab / and /home entries. Then as I know so little about GRUB I used a gui (GRUB Customizer) to probe for the new OS and add an entry to GRUB and the MBR -it makes an /etc/grub.d entry then updates GRUB. On startup, the GRUB list contains the new OS (on sda9) but it boots the first OS (which I copied from -sda5). /boot/grub/grub.cfg contains the new debian OS but it looks like this set root='(hd0,msdos9)' search --no-floppy --fs-uuid --set=root 64662470-0e58-4dfd-90ac-43227d773556 linux /boot/vmlinuz-3.2.0-2-amd64 root=UUID=cc3bca0d-aee4-4b9c-95c2-57212cc36d4d ro quiet initrd /boot/initrd.img-3.2.0-2-amd64 the 1st uuid is of sda9, but the 2nd uuid there is of sda5. I can change the 2nd uuid at startup (with E) and it boots sda9. So how can I get grub.cfg corrected so that the sda9 GRUB list entry boots from sda9 permanently?

  Read the article

• My yum repository able to search packages, but not able to install it in RHEL?

  - by mandy

  I set up yum from dvd. Following is the containts of my .repo file: [dvd] name=Red Hat Enterprise Linux Installation DVD baseurl=file:///media/dvd enabled=0. I'm able to search packages. However while installation I'm getting below error: [root@localhost dvd]# yum install libstdc++.x86_64 Loaded plugins: rhnplugin, security This system is not registered with RHN. RHN support will be disabled. Setting up Install Process Nothing to do My Yum Search output: [root@localhost dvd]# yum search gcc Loaded plugins: rhnplugin, security This system is not registered with RHN. RHN support will be disabled. ============================================================================= Matched: gcc ============================================================================= compat-libgcc-296.i386 : Compatibility 2.96-RH libgcc library compat-libstdc++-296.i386 : Compatibility 2.96-RH standard C++ libraries compat-libstdc++-33.i386 : Compatibility standard C++ libraries compat-libstdc++-33.x86_64 : Compatibility standard C++ libraries cpp.x86_64 : The C Preprocessor. libgcc.i386 : GCC version 4.1 shared support library libgcc.x86_64 : GCC version 4.1 shared support library libgcj.i386 : Java runtime library for gcc libgcj.x86_64 : Java runtime library for gcc libstdc++.i386 : GNU Standard C++ Library libstdc++.x86_64 : GNU Standard C++ Library libtermcap.i386 : A basic system library for accessing the termcap database. libtermcap.x86_64 : A basic system library for accessing the termcap database. Please guide me on this, I want to install gcc on my RHEL.

  Read the article

• postfix test and configuration problem

  - by Woho87

  Hi Guys! I installed postfix using sudo yum install postfix postfix-mysql. I'm newbie to mail systems, but I have one AMAZON EC2 instance with a public DNS. I used the public DNS in most cases, when I configured the file main.cf. The public DNS I have is from amazon and it is a long string(ec2-123-34-234-677.....amazon.com). // I configured this on main.cf. I replaced example.com with ec2-123-.......amazon.com myhostname = mail.example.com mydomain = example.com myorigin = $mydomain mydestination = example.com, $transport_maps local_recipient_maps = $alias_maps $virtual_mailbox_maps unix:passwd.byname home_mailbox = Maildir/ How do I test postfix? I just want it to send emails for my web application. I tried to test it with >telnet localhost 25 after I typed in SSH >sudo postfix start. but I recieve the message that telnet command can not be found. I also use the Amazon linux distribution if you want to know. I use it because it is free. What have I done wrong? Are there anymore configurations required pls help!

  Read the article

• Raspberry pi slows down my entire network

  - by gnusouth

  Whenever my Raspberry Pi is connected to the network (via ethernet) the entire network is slowed to a crawl. On my main computer, ping times for google.com go from ~10ms to ~200ms and it takes forever to load web pages. Connections are also slow on the Pi, with an apt-get update showing pathetic speeds in the order of 1KB/s. Turning off the Pi completely removes the drag from the network. I've tried static and dynamic IP addresses for the Pi, but both have the same problems. I'm currently using Raspbian (downloaded today), but also had this problem with Arch Linux. I've checked the connection's duplex with dmesg | grep -i duplex, which shows that the Pi's connection is running at 100Mbps, full-duplex, as expected. My modem/router is a Billion 7404VNPX (an Australian thing); relatively high-end, albeit a bit buggy at times (it will occassionally delete all its firewall settings). It assigns IPs in the range 192.168.1.1 to 192.168.1.20 and has 192.168.1.254 as its own IP. When I assign static IPs I tend to use the 192.168.1.200 area. Does anyone have any idea as to what could be causing this weird slowdown? Or any tests I could try? Thanks

  Read the article

• RAID 6 that can read with least 1000 Mbit/s?

  - by Diblo Dk

  I purchased a Dell PERC 6/i which I expected to be able to read with 1000 Mbps. There is not much to do now, but there are some things I wanted knowledge about for another time. I have configured it with four 2 TByte drives and RAID 6. It have 256 MByt ram and transfer rate of 300 Mbps. The benchmark test showed: Min read rate: 136.3 Mbps Max read rate: 329,6 Mbps Avg read rate: 242,2 Mbps What could I had done to get at least 1000 Mbps? Is it normal for internal and external RAID controllers to have a lower transfer rate eg. 300 Mbps? (I did not noticed at the time that it was not 3 Gbps) How would a RAID 10 had performed compared to RAID 6 or 5? Would it have been better to use software RAID (Linux) with the internal 3 Gbps SATA controller? UPDATE: The drives is SATA III 6 Gbps. http://www.seagate.com/files/staticfiles/docs/pdf/datasheet/disc/desktop-hdd-data-sheet-ds1770-1-1212us.pdf (2TB)

  Read the article

• DHCPD (Slackware) - Disabling auto-generation of gateway as DNS server

  - by Dogbert

  Good day, I am using a Linux workstation on Slackware 13.37. One "problem" I have had to deal with ever since 11.0 is the following: DNS servers are queried and determined at startup by DHCP daemon (DHCPD) This is invoked at startup by a script located at /etc/rc.d/rc.dhcpd My DNS servers for my ISP are resolved correctly, and are stored in a list located at /etc/resolv.conf However, the one annoying problem is that my gateway IP (ie: 192.168.1.1) is always automatically put at the top of the list in resolv.conf, meaning I have to always wait for a timeout before a valid DNS server is used to resolve an address (ie: timeout on 192.168.1.1 because it is not actually a DNS server, then DHCP uses the next server in the list). I could lower my DNS resolution timeout so the gateway query times out quicker, but that's not what I want, as I don't want to degrade the abilities of legitimate DNS servers. What I would like to do is change how DHCPD operates so that it does NOT put my gateway IP address at the beginning of this list. I've searched via "man dhcpd", etc, and haven't found the exact answer yet. Any help on this issue is appreciated. Thank you all in advance for your time and assistance.

  Read the article

• Getting Started in SuSE as an Ubuntu User

  - by Subhamoy Sengupta

  I am not a Linux newbie, but haven't touched SuSE in a very very long time (last time I tried it, it was SuSE 7!). Finally now I felt like giving it a try, and many things seem strange or unnecessarily complex. I have a series of questions. How do I ensure that my packages are uptodate? It sounds silly, but I tried the obvious methods already. I have disabled the default repositories that show up when you do zypper lr, and added Tumbleweed and packman repositories (Essentials, Multimedia, Extra). Then I did a sudo zypper ref --force and then sudo zypper dup, and it tells me many dependencies are not met. I have already added solder.allowVendorChange=true to /etc/zypp/zypp.conf, so it should not care which repository the latest versions are in, and just upgrade to it. Even when I chose to skip the packages with unmet dependencies, and seemed like quite a bit happened in the background, I opened Firefox afterwards and the version was 7! I am guessing things did not go as expected. But of course this is not a problem with SuSE, but I am not understanding the system right. How do I do it right? When I start typing arguments of a command, for example sudo zypper install, when I type sudo zypper ins and keep hitting TAB, nothing happens! It always worked in Ubuntu and I feel very uneasy with this. Is this how SuSE is supposed to be? When I try to install something, and I start writing its name, even though the package exists and I am sure of it, hitting TAB does not autocomplete it. This is also quite inconvenient. Why is it not happening? There are many things in SuSE that are really great, and I think I will stay with it and not go back to Ubuntu once I settle these very rudimentary issues. But right now they are giving me a lot of grief! Please help!

  Read the article

• logfile deleted on Oracle database how to re-create it?

  - by Daniel

  for my database assignment we were looking into 'database corruption' and I was asked to delete the second redo log file which I have done with the command: rm log02a.rdo this was in the $HOME/ORADATA/u03 directory. Now I started up my database using startup pfile=$PFILE nomount then I mounted it using the command alter database mount; now when I try to open it alter database open; it gives me the error: ORA-03113: end-of-file on communication channel Process ID: 22125 Session ID: 25 Serial number: 1 I am assuming this is because the second redo log file is missing. There is still log01a.rdo, but not the one I have deleted. How can I go about recovering this now so that I can open my database again? I have looked into the database created scripts, and it specified the log02a.rdo file to be size 10M and part of group 2. If I do select group#, member from v$logfile; I get: 1 /oradata/student_db/user06/ORADATA/u03/log01a.rdo 2 /oradata/student_db/user06/ORADATA/u03/log02a.rdo 3 /oradata/student_db/user06/ORADATA/u03/log03a.rdo 4 /oradata/student_db/user06/ORADATA/u03/log04a.rdo So it is part of group 2. If I try to add the log02a.rdo file again "already part of the database". If I drop group 2 and then add it again with these commands: ALTER DATABASE ADD LOGFILE GROUP 2 ('$HOME/ORADATA/u03/log02a.rdo') SIZE 10M; Nothing. Supposedly alters the database, but it still won't start up. Any ideas what I can do to re-create this and be able to open my database again?

  Read the article

• Massive number of context switches on ksoftirqd

  - by Pace

  We have two servers that are grinding to a halt. One is a VM and the other is bare metal. Neither of them are running similar code but they are on the same network. It appears that an incredible number of context switches are arising from ksoftirqd (which is taking up a lot of CPU). vmstat output procs -----------memory---------- ---swap-- -----io---- -system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 0 0 605092 182496 2637556 0 0 0 0 4177 519187 8 19 73 0 0 2 0 0 605092 182496 2637556 0 0 0 0 4792 520980 8 19 74 0 0 3 0 0 605092 182496 2637552 0 0 0 0 2137 659640 18 26 56 0 0 ... pidstat output TCK4-BM-06A:~ # pidstat -w -I 5 Linux 2.6.32.12-0.7-default (TCK4-BM-06A) 07/02/2012 _x86_64_ 03:03:01 PM PID cswch/s nvcswch/s Command 03:03:06 PM 1 0.20 0.00 init 03:03:06 PM 4 386666.27 0.00 ksoftirqd/0 03:03:06 PM 6 0.60 0.00 ksoftirqd/1 03:03:06 PM 8 378213.17 0.00 ksoftirqd/2 03:03:06 PM 10 0.20 0.00 ksoftirqd/3 03:03:06 PM 12 0.20 0.00 ksoftirqd/4 03:03:06 PM 26 377115.37 0.00 ksoftirqd/11 03:03:06 PM 27 1.80 0.00 events/0 03:03:06 PM 28 1.00 0.00 events/1 03:03:06 PM 29 1.00 0.00 events/2 03:03:06 PM 30 1.00 0.00 events/3 03:03:06 PM 31 0.80 0.00 events/4 03:03:06 PM 32 0.80 0.00 events/5 ... My initial thought is that, since both are on the same network, something is flooding the network. Is this consistent with the data?

  Read the article

• Simple Distributed Disconnected way to sync a directory

  - by Rory

  I want to start regularly backup my home directory on my ubuntu laptop, machine X. Suppose I have access to 2 different remote (linux) servers that I can backup to, machines A & B. Machine X will be the master, and should be synced to A and B. I could just regularly run rsync from X to A and then from X to B. That's all I need. However I'm curious if there's a more bandwidth effecient, and hence faster way to do it. Assuming X is going to be on residential style broadband lines, and since I don't want to soak up the bandwidth, I would limit the transfer from X. A and B will be on all the time, however X, will not be, so I'd also like to reduce the amount of time that X is transfering, potentially allowing A and B to spend more time transfering. Also, X won't be connected all the time. What's the best way to do this? rsync from X to A, then from A to B? Timing that right could be troublesome. I don't want to keep old files around, so if I was to rsync, then the --del option would be used. Could that mean something might get tranfered from A to B, then deleted from B, then transfered from A to B again? That's suboptimal. I know there are fancy distributed filesystems like gluster, but I think that's overkill in this case, and might not fit with the disconnected nature.

  Read the article

• ping incorrectly pinging 127.0.0.1

  - by AlexW

  I've got an odd DNS issue. I'm running a dual ipv4/ipv6 environment on Linux. Pinging some sites results in ping pinging 127.0.0.1. e.g. #> ping authserver.mojang.com PING authserver.mojang.com (127.0.0.1) 56(84) bytes of data. 64 bytes from localhost.localdomain (127.0.0.1): icmp_seq=1 ttl=64 time=0.045 ms 64 bytes from localhost.localdomain (127.0.0.1): icmp_seq=2 ttl=64 time=0.043 ms 64 bytes from localhost.localdomain (127.0.0.1): icmp_seq=3 ttl=64 time=0.058 ms --- authserver.mojang.com ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.043/0.048/0.058/0.010 ms Dig, however correctly returns the following: # dig authserver.mojang.com ; <<>> DiG 9.9.3-P2 <<>> authserver.mojang.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 15800 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 1 ;; OPT PSEUDOSECTION: ; EDNS: version: 0, flags:; udp: 512 ;; QUESTION SECTION: ;authserver.mojang.com. IN A ;; ANSWER SECTION: authserver.mojang.com. 5 IN A 54.235.119.47 ;; Query time: 14 msec ;; SERVER: 2001:4860:4860::8888#53(2001:4860:4860::8888) ;; WHEN: Sat Nov 09 15:34:40 GMT 2013 ;; MSG SIZE rcvd: 66 I'm confused! My web browser returns the correct website, and the same computer booted into Windows also works correctly.

  Read the article

• How can I resize images in multiple subdirectories more effectively?

  - by jtfairbank

  I have the original images in a directory structure that looks like this: ./Alabama/1.jpg ./Alabama/2.jpg ./Alabama/3.jpg ./Alaska/1.jpg ...the rest of the states... I wanted to convert all of the original images into thumbnails so I can display them on a website. After a bit of digging / experimenting, I came up with the following Linux command: find . -type f -iname '*.jpg' | sed -e 's/\.jpg$//' | xargs -I Y convert Y.jpg -thumbnail x100\> Y-small.jpg It recursively finds all the jpg images in my subdirectories, removes the file type (.jpg) from them so I can rename them later, then makes them into a thumbnail and renames them with '-small' appended before the file type. It worked for my purposes, but its a tad complicated and it isn't very robust. For example, I'm not sure how I would insert 'small-' at the beginning of the file's name (so ./Alabama/small-1.jpg). Questions: Is there a better, more robust way of creating thumbnails from images that are located in multiple subdirectories? Can I make the existing command more robust (for example, but using sed to rename the outputted thumbnail before it is saved- basically modify the Y-small.jpg part).

  Read the article

• krenew command not working : Permission Denied

  - by prathmesh.kallurkar

  I am using a Linux server to perform my simulations. The login and the file-system of the server are protected using kerberos. The file-system is supported using NFS. Since my simulations take a lot of time to run, my ssh sessions used to hang regularly. So, I have started running my simulations in byobu (similar to screen). In order to make sure that my kerberos session remains active, I am using the krenew command. I have entered the following command in my .bash_profile file. (I am sure that it is called for every login) killall -9 krenew 2> /dev/null krenew -b -t -K 10 So everytime I ssh to the server, I kill the existing krenew command. Then, I spawn a new krenew command -b (which runs in background), -t (I forgot why I was using this option !), and -K 10 (It must run after every 10 minutes and refresh the kerberos cache). When I run the simulations, It runs for 14 hours and then suddenly, I am getting error for reading file Permission Denied Is the command that I am running incorrect ??

  Read the article

• Start Chrome by command line, but adding some arguments to make it login into your Google account automatically

  - by jim

  Is there a way to start Chrome calling it from the command line (using Linux), but providing it some argument to make it login into some Google account automatically? I'm looking for something like google-chrome -account foo -pass bar that I can easily put in a bash script later. A little background: I have a laptop connected to my TV, which is currently using just a mouse for user interaction. There's no google account logged in by default, and that's the way I want to keep it, so my kids can't come across videos and pictures in google and youtube that they are not supposed to see (e.g.: adult content, or anything marked as not appropriate for kids by the google's safe search filters). The bad thing about this is that there are some music videos in youtube that requires you to be logged in to see, usually those we (the adults) used to sing when playing karaoke... as the only input available is a mouse, I'm looking for a way to start with my google account without having to type the whole thing usin the on-screen keyboard. You may think "Why you can't use the keyboard, if the laptop is right there?". Well, it's in a kind of uncomfortable position - too high for me without a chair or something, as it's right above the furniture in where the TV is located. Is there a way to make this scriptable? If not, do you know any other workaround? Note: using the remember me after logging off or alike options are discarded, as the safe-search chrome version must be always the default version to run.

  Read the article

• Monitoring instantaneous network throughput at one second intervals?

  - by Shaddi

  For a testing setup I have, I need to monitor the throughput through a "router"* at regular intervals of around 5 seconds or less (sub-second intervals would be very nice, but not required). Ideally, I would be able to generate a file which contained both the number of bytes and packets seen during each interval. I will eventually be generating a time-series of throughput from this data. On a previous setup using an older version of FreeBSD, there was a tool called "bpfmon" which gave me this information. However, I need to do this under a modern version of Linux (namely, Ubuntu 11.04). I have looked at both iptraf and iftop, but these do not appear to provide the resolution I need, nor do they seem to easily allow scraping the data I need. I understand iptables statistics may be able to give me what I'm after, but the examples I've seen of this seem to rely on repeatedly reading and resetting traffic counters, which seems like it could give inaccurate as read/reset is not an atomic operation. I already capture a tcpdump trace of the traffic I'm interested in on the link I want to monitor, so I am open to approaches which simply parse that. I feel like this must be a common problem though, so I am hoping there will be a standard "best practice" tool for accomplishing this. *I say "router" in quotes because I am really talking about a machine with two bridged NICs through which all the traffic I'm interested in passes.

  Read the article

• Servers/Websites Keep Going Down

  - by Tyler Johnson

  Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps Type: Linux

  Read the article

< Previous Page | 551 552 553 554 555 556 557 558 559 560 561 562  | Next Page >