Search Results

Search found 16415 results on 657 pages for 'computer'.

Page 557/657 | < Previous Page | 553 554 555 556 557 558 559 560 561 562 563 564  | Next Page >

  • Acer Aspire One -- strange battery problem, charges only up to ~90%

    - by houbysoft
    I have this strange problem on the acer aspire one d250. It happened already once before, stayed for about two weeks, and then "fixed itself". The problem is as follows: the battery can't seem to get fully charged; ie the indicator is stuck at about 90% (it's probably not a software problem -- I have ArchLinux and Windows 7 installed and both report exactly the same) and it never passes that value, but it still shows the status as "charging" (I tried everything I could think of -- leaving it charging for extremely long amounts of time, doing a few complete charge-recharge cycles, removing/reinserting the battery, cleaning the connectors, even updating the BIOS, etc., and nothing helped). Also, when it is getting charged, it charges pretty fast until about 70% and then progresses extremely slowly. The battery holds the charge that appears on the battery indicator normally. Just can't get the battery to charge fully -- I can't get it past the 90%. At first I thought this would be a simple battery failure (even if the computer is not that old, about 6-7 months), but as I mentioned it happened once before, and then one day it fixed itself. I tried contacting Acer about this, but the support was not helpful, completely stupid, it seemed like they used canned responses, the usual. Any thoughts on how to fix this?

    Read the article

  • LAN network (switch?)

    - by guywhoneedsahand
    I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

    Read the article

  • ADSL with RFC 2684 Bridging

    - by Axel Isouard
    My new ADSL line is now enabled, I can finally use my Netgear DM111Pv2 to use to the Internet. My ISP has told me a big surprise : I don't need to use a login and a password to connect to the Internet, then I must use the RFC 2684 bridging mode. It works pretty fine on the ADSL modem's side, but I've spent one night trying to figure out how to connect to the Internet through this modem. I only have a Fonera 2.0n and a computer running Gentoo Linux. I've been trying to use the br2684ctl utility with brctl on my Gentoo, first I've configured my kernel in that way : CONFIG_PPP=y CONFIG_PPP_BSDCOMP=y CONFIG_PPP_DEFLATE=y # CONFIG_PPP_FILTER is not set CONFIG_PPP_MPPE=y # CONFIG_PPP_MULTILINK is not set CONFIG_PPPOATM=y CONFIG_PPPOE=y CONFIG_PPP_ASYNC=y CONFIG_PPP_SYNC_TTY=y [...] CONFIG_ATM=y CONFIG_ATM_CLIP=y CONFIG_ATM_CLIP_NO_ICMP=y CONFIG_ATM_LANE=y CONFIG_ATM_MPOA=y CONFIG_ATM_BR2684=y # CONFIG_ATM_BR2684_IPFILTER is not set And I still get these messages : cirus nais # br2684ctl -b -c 0 -e 0 -a 8.35 br2684ctl[8041]: Interface "nas0" created sucessfully br2684ctl[8041]: Communicating over ATM 0.8.35, encapsulation: LLC br2684ctl[8041]: Fatal: failed to connect on socket; No such device The brctl utility keeps telling me "Invalid argument" each time I try to add the nas0 interface into my bridge, I'm honestly hoping I'm doing wrong. I've been following this README carefully and this tutorial on setting up a PPPoE connection with Gentoo, but the PPPoE interface just tries to start, and nothing special related to PPP happens, I can't see the interface when I do ifconfig. So, I'm asking you if there's something huge I've been missing since the beginning ! Maybe I should wait to buy a new router fully supporting the RFC2684 bridging mode, but I'm more interested in setting up this mode on my Fonera 2.0n and even my Raspberry Pi !

    Read the article

  • Windows 8 auto-hibernate from sleep not working on Retina MacBook Pro

    - by frenchglen
    I have a similar question to this one. Only my context is the 15" Retina MacBook Pro - and Windows 8. I have just the original Mac OS X Mountain Lion on there, then Windows 8 via Bootcamp. no rEFIt installed. (I just press ALT every time I restart windows, actually as a security measure to stop tech-unsavvy thugs, who, if the laptop is stolen, think it's only a mac and don't discover my Windows as quickly as they would've, and by that time I remotely activate various anti-theft mac apps and nab them that way). SO: like the related question asks, why isn't it behaving like it should? The Windows 7 FAQ states: Will sleep eventually drain my laptop battery? If your laptop battery charge gets critically low while the computer is asleep, Windows automatically puts the laptop into hibernation mode. But this is just not happening - on my rMBP Windows 8. It seems EVERY time I set the laptop to sleep (when it reaches 10%), then arriving home and plugging it in and hoping to simply resume my work, it does NOT save the session to disk and I lose ALL my work. Who's fault is it? Win 8's (a bug, grr)? Or Apple's EFI system (maybe fixable via editing EFI options/do I have to install refit to make it work perhaps?) Or maybe changing windows power options can somehow fix the problem? Thanks for your help.

    Read the article

  • How do I resolve BSOD: PAGE_FAULT_IN_NONPAGED_AREA?

    - by Burnzy
    I have been trouble shooting this for a few days and cannot fix this anyhow. Computer specifications Mobo: ASUS Sabertooth X58 LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard CPU: Intel(R) Core(TM) i7 CPU 920 (Bloomfield) @ 2.67 ( no OC ) RAM: 6144MB RAM GPU: 2x NVIDIA GeForce GTS 250 1Go in SLI (sli is not enabled anyway at the moment anyway) Drives: OCZ RevoDrive OCZSSDPX-1RVD0120 PCI-E x4 120GB PCI Express MLC Internal SSD [RAID-0]. (I know this could potentilly cause trouble but I had the BSOD before using this drive) Seagate Barracuda 7200.11 ST31500341AS 1.5TB 7200 RPM 32MB Cache SATA 3.0Gb/s 3.5" Internal Hard Drive - Bare Drive Click here for a log of a crash I just had. Click here for a log of a crash I had 30 minutes later, note that it's another driver. Some info Occurence: It seems pretty random so far, haven't noticed any kind of pattern I tried: Windows memory diagnostic (went smoothly at 1066mhz) As I said, it was still happening on my HDD, so when I bought the revodrive I install a new OS on there and still got the error, I believed it happened and I had no drivers installed at that point (not 100% sure) Change the following registry value to 1 (true): HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\SessionManager \MemoryManagement\ClearPageFileAtShutdown Tried to lower even more ram clock Made sure ram timing was set to recommended by manufacturer Verified if motherboard was in good physical condition (yes and its brand new) There is one thing to note, when I got the new motherboard, I installed the new drivers WITHOUT formatting and the I removed the motherboard drivers that I could remove from the control panel (pretty much the first things that have been installed). Could this cause an issue even ON THE OTHER drive (revodrive). Hopefully someone can help me, I am getting tired of this, spending so much money and cannot get this to work correctly. If you need any other information let me know, thank you!

    Read the article

  • Windows Server 2008 32 bit & windows 7 professional SP1

    - by Harry
    I'm testing my new Windows Server 2008 32 bit edition (2 servers) as a server and Windows 7 professional 32 bit as a client. Let say one is a primary domain controller (PDC) and the other is a backup domain controller (BDC) like the old time to ease. Every setup were done in the PDC and just replicate to BDC. Didn't setup anything, just install the server with AD, DNS, DHCP, that's all. Then I use my windows 7 pro 32 bit to join the domain. It worked. After that I tried to change the password of a the user (not administrator) but it always failed said it didn't meet the password complexity setup while in fact there's no setup at all either in account policy, default domain policy or even local policy. Tried to disable the password complexity in the default domain policy instead of didn't set all then test again but still failed. Browse and found suggestion to setup the minimum and maximum password age to 0 but it also failed. Tried to restart the server and the client then change password, still failed with the same error, didn't meet password complexity setup. Tried to see in the rsop.msc but didn't found anything. In fact, if I see the setup in another system with windows server 2003 and windows xp, using rsop.msc I can see there's setup for computer configuration windows settings security settings account policies password policy. I also have a windows 7 pro 32 bit in a windows server 2003 32 bit environment but unable to find the same setting using rsop but this windows 7 works fine. anyone can give suggestion what's the problem and what to do so I can change my windows 7 pro laptop password in a windows server 2008 environment? another thing, is it the right assumption that we can see all the policies setting in windows 7 whether it's in a windows server 2003 or 2008 environment? thanks.

    Read the article

  • Mac OS X L2TP VPN won't connect

    - by smokris
    I'm running Mac OS X Server 10.6, providing an L2TP VPN service. The VPN works just fine when connecting from all computers except one --- this one computer stays at the "Connecting..." stage for a while, then says "The L2TP-VPN server did not respond". In the console, I see this: 6/7/10 10:48:07 AM pppd[341] pppd 2.4.2 (Apple version 412.0.10) started by jdoe, uid 503 6/7/10 10:48:07 AM pppd[341] L2TP connecting to server 'foo.bar.baz.edu' (256.256.256.256)... 6/7/10 10:48:07 AM pppd[341] IPSec connection started 6/7/10 10:48:07 AM racoon[342] Connecting. 6/7/10 10:48:07 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 1). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 2). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 3). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 4). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 5). 6/7/10 10:48:11 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:14 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:17 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). ...and the "retransmit" messages continue until the error message pops up. So far I've unsuccessfully tried: rebooting deleting the VPN profile and recreating it verifying the client's internet connection (it is able to reach the VPN server) connecting through several different networks (in case a router was blocking VPN packets) disabling the Mac OS X Firewall on the client making sure that the VPN settings exactly match those of other working computers running software update (the client is on 10.6.3) Any ideas?

    Read the article

  • "Run As Administrator" on program right click failing and not launching program

    - by GONeale
    This problem lies within a relatively fresh x64 Windows 7 install ~4 weeks, but is also a problem I have seen on Windows Vista machines (x86 versions). Since the other day, any programs attempted to be launched via right clicking on a shortcut (.lnk)'s context menu and pressing - "Run As Administrator" for instance, in the Quick Launch/Jump List in Windows 7 has failed, screen has not dimmed, no UAC popup. In fact the program does not even load. There is no way around this unless I use the shortcut version from "All Programs" which appears to work, very strange? I have performed no major software installs, nothing out of the ordinary. Has anybody encountered this or know what would be causing it? Here's an example of somebody else experiencing this problem in Vista with no solution: http://www.vistax64.com/vista-general/131918-strange-run-administrator-problem.html and I believe this problem is related, I also cannot right click - "Manage" on my computer): http://windows7forums.com/windows-7-support/5501-run-administrator-broken.html I am running the latest version of Avira AntiVir Virus Scanner and pretty concious of what I download, I don't think it is a virus, nor do I believe it is due to the RC Version of Windows 7, because I have seen the problem across multiple Operating Systems versions. Thanks guys.

    Read the article

  • Symbolic directory link shared in domain

    - by Sabre
    We have a file server that is 2008R2 STD, it is a member server in a 2008 AD. I need to relocate some of the files and directories and would like to do it behind the scenes more or less without impacting the users. (Reason for this is that some of the files, due to recent software changes, HAVE to be located locally on one of the workstations, but they can be accessed by other applications remotely.) So symbolic links seem the panacea here, I moved a directory to another network share in the same domain (Windows 7 professional), created a symlink to it in the location it used to be in, named it the same thing, and to the local user it seems almost transparent. I.E. When logged into the desktop of the file server, I can go to the directory, open the link, it leaps to the other share as if it were local, exactly what would be expected. Then I tried it from another client computer (Windows 7 professional as well), went through the normal provisioning of R2R and L2R with fsutil... No joy. What I am getting is an access denied "Logon failure: Unknown username or bad password." using the same account that I log on locally to the file server with (Which happens to be the domain admin) So I cannot believe it is telling the truth, or... I assume it is not passing the credentials I am connecting to the first share all the way through the symlink. The end result is I want users on the domain to browser to share A, inside share A is a mixture of directories/files that reside there, and symlinks to directories/files on the second machine over the network in the same domain. Possible? Or am I misunderstanding how the symlink should work?

    Read the article

  • Customizing user privileges for an account in Windows (xp/vista/7)?

    - by claws
    Hello, I'm a .NET developer and recently learning WINDOWS API. When ever a program starts, my Kaspersky anti-virus says "application belonging to trusted group is trying to set debug previleges". I started wondering what are debug privileges? When ever application tries to open a file (using OpenFileDialog) it gives this message about debug privileges. It sometimes also says the so & so application is trying to read desktop.ini I'm not sure about what exactly it is either. Any way, my concern is about user previlages. When creating user account. We can only set the account to be either Administrative or Limited user. I read in MSDN that there are so many privileges for a user account. http://msdn.microsoft.com/en-us/library/bb530716(VS.85).aspx SE_ASSIGNPRIMARYTOKEN_NAME SE_AUDIT_NAME SE_BACKUP_NAME SE_CHANGE_NOTIFY_NAME SE_CREATE_GLOBAL_NAME SE_CREATE_PAGEFILE_NAME SE_CREATE_PERMANENT_NAME SE_CREATE_SYMBOLIC_LINK_NAME SE_CREATE_TOKEN_NAME SE_DEBUG_NAME SE_ENABLE_DELEGATION_NAME SE_IMPERSONATE_NAME SE_INC_BASE_PRIORITY_NAME SE_INCREASE_QUOTA_NAME SE_INC_WORKING_SET_NAME SE_LOAD_DRIVER_NAME SE_LOCK_MEMORY_NAME SE_MACHINE_ACCOUNT_NAME SE_MANAGE_VOLUME_NAME SE_PROF_SINGLE_PROCESS_NAME SE_RELABEL_NAME SE_REMOTE_SHUTDOWN_NAME SE_RESTORE_NAME SE_SECURITY_NAME SE_SHUTDOWN_NAME SE_SYNC_AGENT_NAME SE_SYSTEM_ENVIRONMENT_NAME SE_SYSTEM_PROFILE_NAME SE_SYSTEMTIME_NAME SE_TAKE_OWNERSHIP_NAME SE_TCB_NAME SE_TIME_ZONE_NAME SE_TRUSTED_CREDMAN_ACCESS_NAME SE_UNDOCK_NAME SE_UNSOLICITED_INPUT_NAME Well, my question is How can I manually (not programatically) set/customize these privileges for a user account? Surprisingly I'm unable to find a PRIVILEGE CONST for registry access. On my lab computer admin has disabled the registry access to my account. Where can I know more information about these information? I use all 3 operating systems (XP, VISTA, 7) :)

    Read the article

  • OS X AFP shares and access

    - by gbrandt
    I am running 10.5.6 Client as a mini server and am having problems with AFP shares. All clients are OS X 10.5.7 I have created three users for 'File Sharing' only on the 'server'. I have created groups and placed these users into specific groups. I have created ACL's to give each group access to certain shares. Two of those users can read and write to any share, one user cannot write to the shares, with different results: when copying a directory, only the directory is created, no files inside are copied, the OS does not give any errors when copying a single file I get three dialogs: "You may need to enter the name and password for an administrator on this computer to change the item named 'xxxx', "The item 'xxxxx' contains one or more items you do not have permission to read. Do you want to copy the items you are allowed to read?, and, The operation cannot be completed because you do not have sufficient priveleges for some of the items. With the single file, a file gets created on the server, but is empty. My ACL for the group this user belongs to is: 0: group:projectmembers allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 1: group:informationtechnology inherited allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 2: group:executive inherited allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 3: group:everyone inherited deny list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit User 1 & 2 belong to informationtechnology and executive and projectmembers, they can read and write freely on the share. User 3 belongs to projectmembers and cannot read and write freely. I have read that this is a UID issue, however User 1 & 2 do not have matching UID's across clients and server and they work, so I don't think this is the case. Any ideas?

    Read the article

  • On a failing hard drive, I am able to view data but unable to copy it - why?

    - by Tom
    I have a 2.5" external hard drive that is failing. It's not making the expected 'clicking' noise that most hard drives and I am able to view the data, but I am unable to actually retrieve the data. I attempted to use SpinRite in order to access the data on the drive, but it didn't like the external drive. When I view the drive's property page, the drive shows that it's used space is at 100% and that it has 0 bytes available; however, the progress indicator under the drive icon in Windows Explorer shows that it's roughly 50% full (which is correct). When I attempt to run Windows' "Error Checking" tool and attempt to "scan for an attempt recovery of bad sectors," the tool begins to run then immediately closes with no error message. I am able to browse the contents of the drive using Windows Explorer. When I begin to try copying any given single file, the copy process begins, an indicator starts, and then the copy fails with no real error message. The Disk Management page in Computer Management under Control Panel also shows this drive has being 'Healthy.' I dropped the drive off at a data recovery store and they said that "The data seems to be intact, but an internal failure is preventing any information from being retrieved." They offered to provide me references to a data recovery specialist. I've also attempted to run CHKDSK on the drive (with and without arguments) but it returns the following error: The type of the filesystem is RAW. CHKDSK is not available for RAW drives. Before going the route of more expensive data recovery, I'm wondering if these symptoms sound familiar to anyone? Other questions... I'm willing to continue trying tools such as TestDisk and/or PhotoRec (as the majority of the data that I'd like to salvage are photos) but how long I should expect either tool to run given approximately 400GB of data? I'm also comfortable using Linux so I welcome any suggestions for utilities or tools and strategies with which you've had success.

    Read the article

  • The physical working paradigm of a signal passing on wire.

    - by smwikipedia
    Hi, This may be more a question of physics, so pardon me if there's any inconvenience. When I study computer networks, I often read something like this in order to represent a signal, we place some voltage on one end of the wire and the other end will detect the voltage and thus the signal. So I am wondering how a signal exactly passes through wire? Here's my current understanding based on my formal knowledge about electronics: First we need a close circuit to constrain/hold the electronic field. When we place a voltage at somewhere A of the circuit, electronic field will start to build up within the circuit medium, this process should be as fast as light speed. And as the electronic field is being built up, the electrons within the circuit medium are moved, and thus electronic current occurs, and once the electronic current is strong enough to be detected at somewhere else B on the complete circuit, then B knows about what has happend at A and thus communication between A and B is achieved. The above is only talking about the process of sending a single voltage through wire. If there's a bitstream and we need to send a series of voltages, I am not sure which of the following is true: The 2nd voltage should only be sent from A after the 1st voltage has been detected at B, the time interval is time needed to stimulate the electronic field in the medium and form a detectable electronic current at B. Several different voltages could be sent on wire one by one, different electronic current values will exists along the wire simutaneously and arrive at B successively. I hope I made myself clear and someone else has ever pondered this question. (I tag this question with network cause I don't know if there's a better option.) Thanks, Sam

    Read the article

  • How do I renew a Web Server certificate in Windows Server 2008?

    - by Mark Seemann
    The SSL certificate for my web site just expired a few days ago, and I would like to renew it. I originally issued it two years ago using my Windows 2008 Certificate Authority, and it's worked without a hitch in all that time, so I would like to renew the certificate as simply as possible to make sure that all the applications relying on that certificate continue to work. I can open an MMC instance and add the Certificates snap-in for the Local Computer. I can find the relevant certificate under Personal, but I can't renew it. When I select Renew certificate with new key I get the following message: Web Server Status: Unavailable The permissions on the certificate template do not allow the current user to enroll for this type of certificate. You do not have permission to request this type of certificate. However, I can't understand this, as I'm logged on as a Domain Admin and I'm running the MMC instance in elevated mode. I've checked the Web Server certificate template, and Domain Admins have the Enroll permission on this template. FWIW, I also tried rebooting the server. How can I renew the certificate?

    Read the article

  • Windows Vista: Screen remains darkened for 30-60 seconds *after* UAC prompt

    - by sf2k
    Fixing someone's Vista computer. Process: I click any program or process that opens a User Account Control prompt. Screen goes dim so you may hit Continue to perform a secure user action. I click Continue Screen goes black for 30 seconds to 1 minute while you wait for the screen to return. In another example I click Cancel and screen still then goes black for 30 seconds to a minute. In that timeframe a chime goes off while you wait. (No chime if it was being cancelled.) Then screen comes back to continue with whatever. Something is occurring after the UAC prompt. Considering everything is practically a UAC acceptance this can get pretty annoying pretty quickly. Laptop has external monitor to regular external plug. Works fine. Laptop also has USB IOGEAR additional external video card. This is problematic but when unplugged same above behaviour occurs. I've ruled out monitor interference since same blackout after the UAC prompt appears with external monitors plugged in or when rebooted with no external monitors. Any suggestions on how to address this problem?

    Read the article

  • Get Python to raise MemoryError instead of eating all my disk space

    - by asmeurer
    If I run a Python program with a memory leak, I would normally expect the program to eventually die with MemoryError. But instead, what happens is that all the virtual memory is used until my disk runs out of space. I am running Mac OS X 10.8 on a retina MacBook Pro. My computer generally has between 10GB to 20GB free. Mac OS X is smart enough to not die completely when the disk runs out of space (rather, it gives me a dialog letting me force quit my GUI programs). Is there a way to make Python just die when it runs out of real memory, or some reasonable amount of virtual memory? This is what happens on Linux, as far as I can tell. I guess Mac OS X is more generous than Linux with virtual memory (the fact that I have an SSD might be part of this; I don't know just how smart OS X is with this stuff). Maybe there's a way to tell the Mac OS X kernel to never use so much virtual memory that leaves less than, say, 5 GB free on the hard drive?

    Read the article

  • Changing the interface language in Windows 7 Home Premium

    - by Cristián Romo
    A friend of mine has recently purchased a laptop in the U.S. that has Windows 7 Home Premium on it with an English interface. Not being a native English speaker, I'm trying to change the interface language to traditional Chinese. I've looked through the Control Panel in search of something that might let me change the interface language. Naturally, I looked at the Region and Language section and managed to change the formats the computer uses and install a working keyboard, but I haven't found a way to change the interface language. Upon doing some research, I found out that there are two kinds of interface packs, Multilingual User Interface (MUI) and Language Interface Packs (LIP). It seems that MUIs can only be installed through Windows Update, so I looked through the list of updates. To my dismay, the language packs are not present. The optional updates tab doesn't even show up. Many sites show a drop down menu the under Keyboards and Languages tab in the Region and Language options, yet it doesn't show up for me. We also don't have the Windows 7 DVD which might contain this useful file. As far as the LIPs go, I can't find one in Chinese at all, let alone traditional Chinese. Can the interface language be changed in Home Premium at all? If it can, how would I do so?

    Read the article

  • Setting "Register this connection's addresses in DNS" using GPO

    - by ChamaraG
    Hi All, I need to get the Windows XP client machines in my network to dynamically update their DNS A records. The network is an AD domain running on Windows Server 2003 R2 servers with Win XP SP3 clients. Some machines already have the "Register this connection's addresses in DNS" check box checked and sucessfully update the DNS server. But some machines do not have this check box set and I need to set this. I read that this is possible using a GPO and I enabled the following: Computer configuration - Administrative templates - Network - DNS client Primary DNS Suffix Dynamic Update DNS Servers Connection-Specific DNS Suffix Register DNS records with connection-specific DNS suffix and where required, entered the relevant parameters. Running rsop.msc in the client machines shows that the GPO has been applied. The client machines have been rebooted. The DNS server allows "Nonsecure and secure" dynamic updates and is only accessible from our internal network. But, the "Register this connection's addresses in DNS" check box is not set. And the hosts without this set are not updating their DNS A records. Per another suggestion in a web site, i tried running "ipconfig /registerdns", but it does not add the DNS A record. Any advice on what I am doing wrong here would be gratefully accepted :-) Thank you.

    Read the article

  • How to install QEMU on Damn Small Linux?

    - by user2934303
    i'm trying to install QEMU on a Damn Small Linux installation in order to emulate pentium features in a 486 computer. Though DSL was descontinued, it's the only linux that runs reasonably on the 486 processor, most recent kernels doesn't even boot on 486 architecture. I tried Tiny Core Linux, but it doesn't work in 486, so i seem to have no escape here. The most recent image of DSL is from 2008, it uses kernel 2.4.x, and i couldn't find a way to compile QEMU on it. Firstly, it lacks several compile tools needed for compiling it, and, it have several dependency problems. I tried some pre-compiled packages, but the only one that worked was a QEMU 5.2 RPM package (it didn't had dependency problems), and it was way too old, it wasn't capable of running windows yet, it just gave me the option of emulating a code, not a full OS as windows, and it also didn't give me the option to choose which architecture i wanted it to emulate (-cpu option). Can anyone help me with this? Also, if someone can think of some alternative to it, i'd be grateful. Thanks.

    Read the article

  • How do I give a user permisson to view scheduled task history on Server 2008?

    - by pplrppl
    I've set up a scheduled task on Server 2008 and want to run it as a user other than the local administrator. So I choose a domain account created specifically for this task and once I've closed the scheduled task and entered a valid password I want to run it and look a the history tab for this task. On the history tab I see: The user account does not have permission to view task history on this computer. What permission must I grant to allow this user to view history and/or how can I view the history as a local admin/domain admin instead of the user the job will run under? Steps to hopefully reproduce: I'm starting from the "Server Manager" - Configuration - Task Scheduler - Task Scheduler Library. IN the top middle pane I have tasks that have been running for several months as the local administrator. In the process of troubleshooting another issue I changed the task to run as Domain\ABCuser. Later in the process of troubleshooting I tried unchecking "run with highest privileges". I have since changed the job back to SERVERNAME\Administrator but the history tab still showed the permissions message. I may have had multiple Server Manager windows open. After Closing the Server Manager and being sure no other management consoles were open I was able to reopen the Server Manager and see the History tab without error. At this point the task works properly but should I ever need to run a task as a task specific account I'd like to know how to make the history viewable. It may be something as simple as closing all Server Manger windows to allow cached permissions to be refreshed the next time you open the Manager but at this point I don't know exactly what the solution is.

    Read the article

  • OS X 10.6 Apply ipfw rules at startup

    - by Michael Irey
    I have a couple of firewall rules I would to like to apply at startup. I have followed the instructions from http://images.apple.com/support/security/guides/docs/SnowLeopard_Security_Config_v10.6.pdf On page 192. However, the rules do not get applied at startup. I am running 10.6.8 NON Server Edition. I can however run: (Which applies the rules correctly) sudo ipfw /etc/ipfw.conf Which results in: 00100 fwd 127.0.0.1,8080 tcp from any to any dst-port 80 in 00200 fwd 127.0.0.1,8443 tcp from any to any dst-port 443 in 65535 allow ip from any to any Here is my /etc/ipfw.conf # To get real 80 and 443 while loading vagrant vbox add fwd localhost,8080 tcp from any to any 80 in add fwd localhost,8443 tcp from any to any 443 in Here is my /Library/LaunchDaemons/ipfw.plist <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple Computer//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Label</key> <string>ipfw</string> <key>Program</key> <string>/sbin/ipfw</string> <key>ProgramArguments</key> <array> <string>/sbin/ipfw</string> <string>/etc/ipfw.conf</string> </array> <key>RunAtLoad</key> <true /> </dict> </plist> The permissions of all the files seem to be appropriate: -rw-rw-r-- 1 root wheel 151 Oct 11 14:11 /etc/ipfw.conf -rw-rw-r-- 1 root wheel 438 Oct 11 14:09 /Library/LaunchDaemons/ipfw.plist Any thoughts or ideas on what could be wrong would be very helpful!

    Read the article

  • OSX: Mimic Ubuntu IP Masquerading via iptables with ipfw

    - by Dogbert
    Good day, I am attempting to replicate a setup I have between a router and an Ubuntu PC, and have the same setup working on my MacBook (10.6, Snow Leopard). First, I have a router that has a USB port. When I plug it into my Ubuntu PC, it creates an RNDIS connection, allowing me to connect to the router over the USB cable via an IP connection. When I plug it into my computer via USB, it gets assigned an IP address of 172.16.84.1, and a new adapter appears when I type ifconfig. I can then SSH into the device via ssh [email protected]. When I log in to the device, I flush the routes, then create the default route: admin@localhost> route -f admin@localhost> route add default 172.16.84.2 Now, in my Ubuntu machine, I use iptables to enable IP masquerading: root@Valhalla> sudo iptables -t nat -A POSTROUTING -s 172.16.84.2 -j MASQUERADE Once this is all done, the router has internet access over the USB connection to my PC. I am trying to replicate this exact setup on my MacBook now (Snow Leopard), but iptables does not exist for OSX, not even a Macports version exists. I have scoured through other questions on StackOverflow that cover the usage of the ipfw command, which apparently works as a drop-in replacement for iptables. However, the syntax is significantly different, and I'm pretty much lost. Does anyone with some experience with ipfw have some suggestions on how I could accomplish this and create a NAT connection via IP masquerading like I could with my Ubuntu PC? Thank you for your assistance.

    Read the article

  • IE9 will not navigate to some websites but Google Chrome can

    - by Storchburp
    Was recommended by a friend to ask for help here. I am using Internet Explorer 9. As of two days ago I was suddenly unable to navigate to any part of the following websites: www.computerandvideogames.com www.deviantart.com www.cnet.com However I can still access all of them normally through Google Chrome. I am on a college network but these sites are also accessible through fixed terminals provided by the school and are definitely not blocked. I do not know of any other sites similarly affected. There is no popup, no error message, no diversion to a site telling me I can't access / am blocked etc. I can be on www.google.com and attempt to access these sites through the URL or google search, and my cursor will just show the little moving blue wheel next to the arrow for a couple of seconds, and the page displayed on my browser will not change; ie. not navigating at all. Running antivirus software, changing proxy settings in IE, clearing cookies, unplugging/plugging in computer, restarting PC etc have not changed the situation. Any assistance or advice would be greatly appreciated. Thanks in advance.

    Read the article

  • There's a stray current flowing from my monitor through the VGA cable to the PC. Is this safe?

    - by EApubs
    I have two monitors in my machine. One is an old LCS samsung monitor. Recently, I started to hear a small hum in my speakers (subwoofer) and replaced them. The new one also got the issues then I found our that its a grounding issue. I unplugged the PC's power chord. The monitor is still switched on. When I checked, there's current in the earth pin (ground pin). When I unplug the monitor, there's no current and the speaker is normal. Now, I have moved that monitor to my dad's machine and took his monitor. My question is, is it a big issues? The house's earthing system is working and its grounding the current. I won't feel it if I touch the machine like in many other cases. But still, is it good to keep that monitor attached to my machine? Can it harm the computer? What should I do?

    Read the article

  • Can't ping a DNS zone on windows server 2008 R2

    - by Roberto Fernandes
    I´ve just configured a windows server 2008 r2, but got a lot of problems on DNS role. Let me talk about the server configuration: name: fdserver IP address: 192.168.0.10 I have a DNS zone called "fd.local". This is my domain and it´s working ok. I´ve created a zone called fdserver, and inside this zone a record (A) with "*" as a host. because this is a webserver, i´ve configured apache so if you enter something like "site.fdserver" it will point you to the "site" folder. This is working ok ONLY inside the server. This server is a DNS server too... and have 3 entries: 192.168.0.10 (his own IP), 8.8.8.8 and 8.8.4.4 (google public DNS). Now start the problems... Most of the computers on my network, CAN join the domain without problems. But just CAN'T ping "something.fdserver". Now comes the strange thing... If I remove the twoo secondary entries on my DNS server (8.8.8.8 and 8.8.4.4), it obvious stop accessing websites (like microsoft.com), but now the computer CAN ping "something.fdserver". I don´t know If I explained correctly... and my English is terrible... but inside the server is all working as it supposed to work. But in the workstation machines, it work only if I remove the secondary DNS!! If you need any details, just ask! thanks!

    Read the article

< Previous Page | 553 554 555 556 557 558 559 560 561 562 563 564  | Next Page >