Search Results

Search found 15777 results on 632 pages for 'desktop computers'.

Page 559/632 | < Previous Page | 555 556 557 558 559 560 561 562 563 564 565 566  | Next Page >

  • What's hogging my CPU?

    - by endolith
    Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. I try killing lots of things, but it continues at 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, that normally only hits 100% CPU when I'm doing something that requires it (like loading 32 Firefox tabs) after which it goes back to a normal idle level. It's not a new install or anything. It shouldn't be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing any process I saw active again, and killing vino-server finally fixed the problem, even though it never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). How did it manage to use 100% CPU while top only showed it as 5% or so? How do I identify the culprit in the future? Looks like I'm not the only one: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

    Read the article

  • RTL8192SU Linux Issue Installing Driver

    - by s32ialx
    OK I've read tons of fourms of people getting the onboard RTL8192SE working and the RTL8192SU working dif is U = USB they are both N and i have both Toshiba L500D-00T pre-installed Win Vistax64-HP and i have obtained the free Win7x64-HP upgrade the onboard wificard sucks and can't hold a stable connection for more then 20minutes in windows but the usb is amazing. Now problem is i tried both Ubuntu and Mandriva with no resolve the issue is the onboard drive detects and actually SHOWS that it's there but no wireless networks detect so it's saying no SSID's are broadcasting which i know is a lie since I'm running a 2wire bell dsl modem with built in wifi and a Linksys wrt54g w/ DD-WRT firmware and both are broadcasting fine. Why don't i use the USB? In the hardware device manager in mandriva it shows up as unknown but shows that it's realtek and that it's a 8192 chipset. but no option to for a driver install and when i do a make in terminal i get this error and no clue what it means [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# make make: *** /lib/modules/2.6.31.12-desktop-3mnb/build: No such file or directory. Stop. make: *** [all] Error 2 [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# any help appreciated. and just encase I'm running currently Mandriva Spring 2010 Free

    Read the article

  • Linksys/Cisco Small Business SRW-Series (ie SRW248G4) - Overcoming the Limitations

    - by Warren P
    We just purchased a Cisco/Linksys SRW 248G4 switch to try it out. We have always had unmanaged switches before, and this is our first "somewhat managed" switch. So far the major limitations are: Only Internet Explorer 6 (manual says IE 5.5!) works for the web interface SSH exists but is not practically useable because the only key length that is supported is no longer even used by most modern SSH installs. (I get the error "RSA modulus too small" in openssh 4.x/5.x) This is with the latest firmware revision, I believe, although Cisco's website does not actually tell you what version you're downloading. All in all, I think, they must be trying to tell me that if I want a good-quality switch, I shouldn't buy these SRWs and should buy a Dell or an HP ProCurve, or save up my pennies, and buy a Catalyst. The question here, then, at long last: Has anyone gotten the web-browser to work via some IE 7 or IE 8 compatibility mode settings or used another browser (Opera? KDE/Safari/WebKit?) and spoofed IE6? Is there any way to get the SSH key length upgraded? I'm guessing a 0% chance of a yes on that last one. I found an XP machine, used telnet (via PuttyTel.exe) and IE6 to set this up, and I doubt we'll have to touch it again. Which is fine with us. But it would be nice if I could administer this thing from either (a) a linux box, or (b) my primary desktop which is windows 7. It looks like XPMode with IE6 on the virtual XP machine may be my only way to administer this type of switch via the web.

    Read the article

  • How to multiseat with HW 3d accel on CentOS 6.3 Final?

    - by user35070
    I would like to setup a multiseat configuration on CentOS 6.3 (two video cards, two keyboards, two mice, two monitors) and have hardware accelerated 3D on both monitors. 3D HW acceleration rules out Xephyr. I saw somewhere that recent versions of GDM (3.3 and newer?) don't support multiseat, so do I have to install KDM to make this work? If I just create a duplicate section with new device identifiers in my xorg.conf file, will this 'just work'? Using different ports on the same video card and separate keyboards, mice, and displays, the result was a desktop which spanned both monitors with both keyboards and mice acting as the same input in the GUI. I will power down and put in the new video card and report on the results soon. Both video cards are nvidia. UPDATE after putting in another NVIDIA video card, default behavior (before changing xorg.conf) is that one screen works normally, and both mice and keyboards are connected to it. Changing xorg.conf and the display manager to KDM and following the directions here https://help.ubuntu.com/community/MultiseatX#Ubuntu_10.04_.28Lucid.29 , I have 2 mirrored screens connected to separate video cards, DRI enabled, and 2 mice both connected to the same pointer. Keyboards don't do anything, however, I probably just need to fix a setting in xorg.conf I would still like to get multiseat functionality, eg. separate screens with separate input devices I have verified that the separate X processes are running (see page above) using 'ps aux | grepX [01]'

    Read the article

  • Free or Open Solution for Storing and Charting CSV data

    - by rrrfusco
    I'm presently storing CSV files, combining them, opening them in open office, creating pivot tables and then generating charts from the spreadsheet. I've looked at OOBase, but appending csv files to base is clunky for some reason. SQLite seems like a good database solution, but I've haven't found a good charting program that connects to it with ease. Although open office (or libreoffice) maintains the references and allows you to update the information, this process is far from efficient. There are too many steps and it seems one program should handle all of these tasks. A better program would be more intuitive, allow you to simply add inserts into a database, and include an interface for standard charting settings. EDIT Simplest Automated Analysis and Chart Generation Tool? The above answer references Spotfire and Tableau, each of which has a free 14 and 30 day trial. Each program is nicely streamlined and designed. I'm looking for a program between this quality and LibreOffice. Can you recommend a better open or free desktop solution for windows?

    Read the article

  • what's the difference between a Volume and a Partition in Windows 7 diskpart

    - by user170232
    I was trying to follow the Intel guide for setting up iRST (Intel Rapid Start Technology) on my new laptop. The Intel manual says you need to create a *Volume that is as big or bigger than your available memory, set it to a specific id (id=84), then go into the iRST tool and adjust some settings. Looking at the disk manager on the laptop, I see there is already a Partition labeled as "Hibernation Partition" which is a little bigger than the memory in my system. So it looks like iRST was already set up...BUT, it's a Partition, not a Volume. Here's what the manual says to do: (from: http://download.intel.com/support/motherboards/desktop/sb/rapid_start_technology_user_guide.pdf) diskpart list disk select disk x (where x is the disk to use, there's only one disk in this laptop) create partition primary size=X000 (where X000 is the size to create) detail disk (which lists details for the disk. This is where i get hung up) select volume Z (where Z is the *partition you created previously) ** it says the 'detail disk' command will list the volume #, but it doesn't. ** 'detail disk' only lists two "volumes" for Recovery and OS. ** if i do 'list partition', i see the 8 GB *partition labeled as "Hibernation Partition") ** so I can't continue with the following steps: set id=84 override exit The reason I went looking for the manual is because when iRST is enabled in the BIOS, the system won't resume from sleep. When it's disabled, it works fine, but the system goes into (legacy?) Hibernation mode and takes a while to come out of Hibernation. the iRST is supposed to resume from deep sleep very quickly. So, what's the difference between a Volume and a Partition? Should I delete the Hibernation Partition and create a Hibernation Volume? Anyone have any ideas? (if it matters, this is on a Dell XPS 13 with BIOS A08) Thanks! J

    Read the article

  • problem booting crusty old windows XP

    - by Carson Myers
    I have an acer aspire laptop running Windows XP home. I believe I have some virus on it, I'm not sure--I mostly just run linux in a VM on it so I wasn't too worried. I'm not sure if that virus caused this problem. The laptop wasn't recognizing my USB hard drive for some reason so I decided to restart it. When it started up, it got past the memory test, past the boot screen, (but it paused right here on a blank screen for awhile) and flashed the desktop once (like it does just before the login screen) and then crashed. I got a quick BSOD and then it restarted. Then it tried to boot again, etc etc infinite loop of failure. Well, before trying safe mode, I disabled automatic restart on system crash so I could read the blue screen. There wasn't anything important on it, it said *** STOP: 0x00000000 (0xC0000000 0x,.... ) beginning physical memory dump physical memory dump complete That's not verbatim (obviously) but it didn't help me. so I booted in safe mode, and it stopped on the driver gagp30kx.sys and then restarted (and infinite loop of failure again). I burned a recovery CD and tried that. It loaded it, and I went into repair mode. I ran chkdsk and then disabled the AGP driver. Same thing on booting in safe mode except it stopped at mup.sys instead. I enabled the AGP driver again, and ran chkdsk again from the CD. It said it found problems but didn't say it fixed them. So I ran it a second time, and it said "performing additional checking or recovery" lots of times (I can't tell how many, they went above the screen top). I tried booting again and no luck. Every time I run chkdsk after trying to boot again it says it found and fixed more errors. I think it might be whatever driver is after the AGP driver, but I don't know what it is or how to find out. Can anyone help me fix this?

    Read the article

  • Unable To Successfully Use Java Anywhere (Windows 7 64bit)

    - by Nathan Smith
    This is a bit of an odd issue: (This is with JRE 7u7 32bit.) New Lenovo W530 laptop, everything is shiny. I tried to use a java applet for the first time recently (in Chrome). I got the Java logo and it started spinning like it was going to load, but didn't get anywhere and the browser locked up. I tried IE. Same deal. Tried Firefox. Same deal. So, I did the usual things: Rebooted, nothing. Un-installed Java, rebooted, re-installed, nothing. Tried it installing a 64bit Java as well. Same thing. I tried JRE6. Same thing. I uninstalled and manually deleted all the registry entries I could find related to it, then re-installed. Same thing. I un-installed and used the JavaRa utility. Same exact thing. I've not been able to use web applets or desktop stuff (minecraft), until yesterday. I did a graphics driver update and I was able to play minecraft for small amounts of time. It crashed regularly and wouldn't start reliably. No change in web applets. I'm at my wits end here. I'm to the point where reformatting is my only option. If anyone has any ideas at all, that would be awesome.

    Read the article

  • Can't find disk usage in one directory

    - by Xster
    Similar questions are asked frequently but no suggested answers solved my issue. I have some disk space usage that I can't find as well. In df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 144183992 136857180 2652 100% / udev 2013316 4 2013312 1% /dev tmpfs 808848 876 807972 1% /run none 5120 0 5120 0% /run/lock none 2022116 76 2022040 1% /run/shm overflow 1024 0 1024 0% /tmp I checked the inodes, I checked lsof for +L1 or deleted files, I rebooted, I checked for files hidden behind mounts but none of them were the issue. It grows periodically and I'm running out of things to delete to feed the beast. It's all in the home directory of the only user I have. In du in ~ du -h --max-depth=1 192K ./.nv 2.1M ./.gconf 12K ./Pictures 1.6M ./.launchpadlib 12K ./Public 24K ./.TemporaryItems 8.9M ./.cache 12K ./Network Trash Folder 28K ./.vnc 11M ./.AppleDB 48K ./.subversion 1.9G ./.xbmc 8.0K ./.AppleDesktop 12K ./.dbus 81M ./.mozilla 12K ./Music 160K ./.gnome2 44K ./Downloads 692K ./.zsh 236K ./.AppleDouble 64K ./.pulse 4.0K ./.gvfs 1.4M ./.adobe 44K ./.pki 44K ./.compiz-1 168K ./.config 1.4M ./.thumbnails 12K ./Templates 912K ./.gstreamer-0.10 8.0K ./.emacs.d 92K ./Desktop 1.3M ./.local 12K ./Ubuntu One 12K ./Documents 296K ./.fontconfig 12K ./.qt 12K ./.gnome2_private 20K ./.ssh 20K ./.mission-control 12K ./Videos 12K ./Temporary Items 640K ./.macromedia 124G . I can't find a way to figure out how it got to that 124G in that directory. There are no mount points in home.

    Read the article

  • Maximum RAM on Biostar P4M8PM7 Socket775 mATX board

    - by Alex Balashov
    I have a server with a Biostar P4M8PM7 ("Pro-M7") board based on a VIA chipset. It's a strange board to put in a server because it seems like more of a desktop board to me, but alas! It takes DDR2-667 (PC5300) RAM. What I can't figure out is the maximum amount I can put in it, as I cannot find the manual anywhere online. I've found a few marketing broadsheets from online retailers that say, "up to 2 GB of RAM!" but I am not sure whether to believe them. They also do not seem to be quite for the same board, as they indicate DDR2 400/533 RAM, for example: http://www.geeks.com/details.asp?invtid=P4M8P-M7. The manufacturer's web site says the same thing, but does not elaborate. It's a 64-bit CPU and board; is there a technical reason why the board would not be able to address more than 2 GB? Can someone tell me what sort of that reason that would be? I bought this server from someone really hoping I could put 8 to 16 in it, and wanted to do some research before I gave up. On a related note, it's not indicated anywhere whether it can take ECC RAM; the existing chips are not ECC, but most memory sold in the range I'm looking for (e.g. DIMMs with enough chip density to do 8 GB) seems to be server-class and for that reason ECC. Any ideas? Thank you very much for your consideration in advance!

    Read the article

  • Acer Aspire One getting extremely hot

    - by ascom
    I have an Acer Aspire One D250-1197. I really better type fast before it overheats again... For some reason, I'm having a problem with heat on my netbook only when I run Joli OS (Ubuntu 9.10 LTS?). When I leave it idle, with nothing running (other than the regular Joli OS desktop and a couple of doing-nothing terminals), heat slowly builds up to the point where the netbook is burning hot to the touch. I have never had this problem when running Windows 7 Starter (even though it gives me plenty of other headaches). It seems that the fan is spinning, but not fast enough to keep up with the heat buildup. Is there something wrong with the fan drivers? The computer doesn't seem to recognize that it is overheating. What can I do to solve this problem (other than shut it off or use Windows)? I'm currently on the wrong side of Earth (I mean, on vacation), so I just need a temporary fix, such as a driver I can install. Also, I have to use Linux, because I have to share out the wired connection in hotels wirelessly to the iPhones. EDIT: I'm switching from Joli OS to a more "proper" and up to date distribution (Xubuntu 13.04). I'll see if it still has the heat problem and try @nod's cpufreq idea.

    Read the article

  • Intel z77 vs h77 for intensive compiling, gaming [closed]

    - by Bilal Akhtar
    I'm in the market for a desktop motherboard (preferably ATX) that functions well with Intel i7-3770 Ivy Bridge processor at 3.4 GHz with LGA1155 socket. That processor is very fast, and it should handle all my tasks. My question is about the type of motherboard chipset I should choose to accompany it. I plan to use my rig for compiling and developing Debian package and other OS components, web development, occasional Android apps, chroots, VMs, FlightGear, other gaming but nothing serious, and heavy multitasking, all on Ubuntu. I do NOT plan to overclock, and I never will, so that's not a cause of concern for me. That said, I'm down to three chipset choices: Intel H77 Intel Z68 Intel Z77 I'm planning to go for H77 since I don't need any of the new features in Z77. I don't plan to use a second GPU and I will never overclock my CPU/GPU. My question is, will H77 based MoBos handle all my tasks well? Intel advertises that chipset as "everyday computing" but other sites say it's base functionality is the same as Z77. Intel rather advertises Z77 for "serious multitaskers, hardcore gamers and overclocking enthusiasts". But the problem with all Z77 motherboards I've seen is, they're way too expensive and their main feature seems to be overclocking, which won't be useful to me. Will I lose any raw CPU/GPU performance or HDD R/w with the H77 when comparing it to a Z77? Will heat, etc be an issue too? From what I've seen, Z77 motherboards have larger heat sinks when compared to H77 ones. Will that be an issue too, if I go with an H77 motherboard with no heat sinks for the chipset? The CPU will have a fan in both cases, of course. tl;dr When it comes to CPU/GPU performance and HDD r/w, is the Intel H77 chipset slower than the Z77? I don't care about overclocking or multiple GPUs, and for the processor, I'm set on Ivy Bridge i7-3770.

    Read the article

  • Setting up dnsmasq for a local network

    - by WishCow
    Me, and a small group of developers have just moved to a new office, and I'd like to set up dnsmasq on our development server, so when we deploy web apps there, we don't have to edit our own hosts files. We have a router at 192.168.3.1 which we don't have access to. I figured I'd install a DNS server on the development box, and we all record it's IP as a secondary DNS server. Unfortunately I'm strugling to make this work. The name of the devel server is devbox, it's IP is 192.168.3.99, and it's running the latest Ubuntu Server (Karmic) My computer is running Ubuntu Desktop (Karmic) What I'd like to achieve Let's say I have three websites, website1, website2, website3, running on the development box. I'd like to access them by the urls: http://website1.devbox http://website2.devbox http://website3.devbox So I have configured Apache on the devel box, installed dnsmasq, and put the following lines into it's hosts file: 192.168.3.99 website1.devbox 192.168.3.99 website2.devbox 192.168.3.99 website3.devbox and edited my own resolv.conf file to include the devel box as a nameserver: nameserver 192.168.3.99 It's working fine, I can access the sites. The problem is that it doesn't scale well. I'd like all the domains ending with .devbox forwarded to the development box, and this is what I'm struggling with. I have tried putting 192.168.3.99 devbox into the hosts file, and editing the line in dnsmasq.conf: # Add local-only domains here, queries in these domains are answered # from /etc/hosts or DHCP only. local=/devbox/ But I cannot get it working. If I try any url that is not explicitly present in the development box's hosts file, the dns lookup fails. Is the local directive for something else? Am I looking at the wrong place?

    Read the article

  • Automatically install driver on headless WHSv1 system

    - by Dan Neely
    I have one of the HP Mediasmart Windows Home Server v1 boxes. It's network port appears to have died a few days ago but the system is not giving any other sign of failure: No activity lights activate on either side of the cable when connected to my gigabit switch; when connected to one of my routers 100 megabit ports the lights turn on but it remains unreachable over the network and my router never lists it as among DHCP clients. I bought a USB-ethernet adapter to temporarily get it back online; but the adapter needs a driver to work which I can't install because the system is headless by design (no video out, no PCI/PCIe slots) with admin access only available via the WHS client or remote desktop. Both of those options require network connectivity and are consequently unavailable. I tried copying the drivers to a flash drive; but Windows either didn't look there or none of the drivers provided were suitable (Win8, Win7, or combined XP and Vista). I've been told that a USB WiFi adapter would have the same driver problem.

    Read the article

  • Setting up dnsmasq for a local network

    - by WishCow
    Me, and a small group of developers have just moved to a new office, and I'd like to set up dnsmasq on our development server, so when we deploy web apps there, we don't have to edit our own hosts files. We have a router at 192.168.3.1 which we don't have access to. I figured I'd install a DNS server on the development box, and we all record it's IP as a secondary DNS server. Unfortunately I'm strugling to make this work. The name of the devel server is devbox, it's IP is 192.168.3.99, and it's running the latest Ubuntu Server (Karmic) My computer is running Ubuntu Desktop (Karmic) What I'd like to achieve Let's say I have three websites, website1, website2, website3, running on the development box. I'd like to access them by the urls: http://website1.devbox http://website2.devbox http://website3.devbox So I have configured Apache on the devel box, installed dnsmasq, and put the following lines into it's hosts file: 192.168.3.99 website1.devbox 192.168.3.99 website2.devbox 192.168.3.99 website3.devbox and edited my own resolv.conf file to include the devel box as a nameserver: nameserver 192.168.3.99 It's working fine, I can access the sites. The problem is that it doesn't scale well. I'd like all the domains ending with .devbox forwarded to the development box, and this is what I'm struggling with. I have tried putting 192.168.3.99 devbox into the hosts file, and editing the line in dnsmasq.conf: # Add local-only domains here, queries in these domains are answered # from /etc/hosts or DHCP only. local=/devbox/ But I cannot get it working. If I try any url that is not explicitly present in the development box's hosts file, the dns lookup fails. Is the local directive for something else? Am I looking at the wrong place?

    Read the article

  • Enabling AHCI in BIOS for SSD

    - by Robert
    I am trying to help a friend with a desktop upgrade. It is an old machine with an Intel DG31 main board. The board has 1 IDE port to which a DVD-ROM drive is connected, and 2 SATA ports. 1 SATA port had a hard drive with XP on it. I have made that the secondary drive now and wiped the OS as requested, so it is just for data. The new SSD has been installed but I read that for best results one must enable AHCI in the BIOS? So I checked and in the BIOS there is a SATA Mode setting with 2 options - Native and Legacy. I think Native means AHCI? After setting to Native, I installed Windows 7 Home Premium and all the latest drivers from Intel's website and all Windows Updates. Now when I check Device Manager I see this: Also Microsoft says HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msahci\Start and HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\IastorV\Start should have value 0 for AHCI but I see that the value is 3 for both. So does this mean that Native mode is not AHCI? Or Windows 7 ignored BIOS setting and installed in IDE mode, maybe because both cables are present? Please help me enable AHCI on this system. Thanks!

    Read the article

  • Ripping CD Audio simultaneously from 2 drives on one PC via USB or PATA - rip accuracy preserved?

    - by Rob
    I'm considering ripping audio (reading audio) from CDs using 2 drives simultaneously to speed up the process of ripping the CDs - i.e. 2 at a time rather than 1. Are there any issues with achieving maximum rip accuracy? In general I wondered if people have tried this and if the simultaneous streams from both rip activities would overload the host machine and cause packet loss or read retries resulting in a sub-standard CD-DA Audio CD rip? If it just means the rip is slightly slower (but still faster than sequentially doing one rip followed by another) but still of maximum accuracy then that is OK for me. I will be using dbPowerAmp to rip the CDs and converting to FLAC lossless format. Specific examples: There are 2 machines I intend to do it on: A Toshiba NB100 1.6Ghz Atom netbook, 2Gb RAM, running Windows XP Home with 1 external LG DVD/CD burner and external 1 LG Blu-ray burner attached via USB 2.0, ripping to the machine's 5400rpm internal hard drive. This rips from one CD drive very well, more than adequate, it is a nippy, fast little machine for its specification. A Desktop PC running Windows 7 Home Premium with MSI P4M900M2-L/ MS-7255v2.0 motherboard and 1.86Ghz Intel Core 2 Duo E6320, 7200rpm hard drive and 2Gb RAM, with an internal LG PATA DVD/CD burner (master) and a Philips DVD/CD burner (slave) on the same PATA bus (perhaps separate buses would be another option to consider here). Thoughts?

    Read the article

  • Tips on setting up a virtual lab for self-learning networking topics

    - by Harry
    I'm trying to self-learn the following topics on Linux (preferably Fedora): Network programming (using sockets API), especially across proxies and firewalls Proxies (of various kinds like transparent, http, socks...), Firewalls (iptables) and 'basic' Linux security SNAT, DNAT Network admininstration power tools: nc, socat (with all its options), ssh, openssl, etc etc. Now, I know that, ideally, it would be best if I had 'enough' number of physical nodes and physical network equipment (routers, switches, etc) for this self-learning exercise. But, obviously, don't have the budget or the physical space, nor want to be wasteful -- especially, when things could perhaps be simulated/emulated in a Linux environment. I have got one personal workstation, which is a single-homed Fedora desktop with 4GB memory, 200+ GB disk, and a 4-core CPU. I may be able to get 3 to 4 additional low-end Fedora workstations. But all of these -- including mine -- will always remain strictly behind our corporate firewall :-( Now, I know I could use VirtualBox-based virtual nodes, but don't know if there are any better alternatives disk- and memory- footprint-wise. Would you be able to give me some tips or suggestions on how to get started setting up this little budget- and space-constrained 'virtual lab' of mine? For example, how would I create virtual routers? Has someone attempted this sort of thing before: namely, creating a virtual network lab behind a corporate firewall for learning/development/testing purposes? I hope my question is not vague or too open-ended. Basically, right now, I don't know how to best leverage the Linux environment and the various 'goodies' it comes with, and buying physical devices only when it is absolutely necessary.

    Read the article

  • Recommendations for secure business collaboration tools

    - by Michael Prescott
    I'm searching for a secure and easy way for business partners to collaboratively edit and exchange documents, share calendars, create schedules, and assign tasks. I speculate that the ideal collaboration environment or work-flow would actually involve several technologies and services. My co-workers and I have tried a variety of things from Google Apps to Wiki's, but nothing feels very fluid or complete. I suppose defining what we need and our constraints is probably in order: collaboratively edit basic text documents and spreadsheets exchange documents like flow-charts, graphs, and files generated by our other desktop applications, but not source code assign tasks to each other and ourselves and track the history of those tasks easily see when relevant documents have been modified since last viewing and ability to easily push notifications to relevant workers (a clean front page that shows updates would probably suffice) provide limited access to contract workers and guests users if a remote user system is compromised (keystroke logger or other spyware) we don't want the criminal to be able to gain access to all business documents (processes, trade-secrets, customer lists, etc.) simply because they gained access to a single Google account (or whatever web service) Cannot be a difficult to administer VPN infrastructure Cannot cost more than $100 per month (yeah, money is tight) Needs to support up to 25 users We can host our own web applications, but it must be low maintenance solution

    Read the article

  • Lightweight Linux distro that includes developer tools? (or, the most BSD-like Linux)

    - by RevAaron
    I cut my teeth on Minix and Slackware 1.1, but I've been in the OS X Wilderness for the last few years. I'm trying to standardize on a Linux distribution for personal and work-related use on less powerful laptops and under virtualization. So far, NetBSD and OpenBSD are the best fit for my purposes- but after plenty of frustration I've come to the conclusion that I need to stick with Linux to get the hardware and software support that comes with it. What I like about NetBSD/OpenBSD that I'd like to keep: X, but no default KDE, GNOME or XFCE! A sensible /etc and dot file setup- startx calls xinit, xinit looks for ~/.xinitrc; nothing more complicated than that is needed. Command line tools and file-based configuration: I shouldn't need a GUI to connect to a WAP. Decent selection of binary packages; building from source is OK, but nothing source-only like Gentoo. pkg_add (BSD) and apt-get both have treated me well in the past. Modest RAM and HDD requirements: boot + X + awesome+ two xterms takes up 80 MB on OpenBSD and 240 MB on Debian 5 and Crunchbang In my experience, most "lightweight" and Live CDs focus on a nice desktop environment crammed into a CD or USB stick; once you add build-essentials you end up with something just about as bloated as Ubuntu or Debian full install. Crunchbang is a great example. Thanks in advance for all suggestions!

    Read the article

  • How do I use a self encrypting drive?

    - by Unique_Key
    I recently purchased a Micron RealSSD c400 self encrypting drive, and I am having a few issues when trying to get it recognized by my laptop (HP Elitebook 8440p running Windows 7 x64; also tried on a custom-built desktop). When I try to initialize the drive from disk management, I get a CRC error; also, when attempting to partition it from Windows setup, the program can't create the partitions. I also tried with UBCD, nothing. I assume this is due to drive security, but I haven't been able to find much information about this online; do I need a management software or something? I'm completely stumped here. EDIT As requested, when I try partitioning the device from Windows setup I get a 0x80300024 error; when I try initializing it from disk management, I get a "Data error (cyclic redundancy check)" message, and the event log shows the following under System: Source: VDS Basic Provider, message: unexpected failure. error code 490@01010004 (2x) Source: Virtual Disk Service, message: VDS fails to write boot code on a disk during clean operation. Error code: 80070001@02070008 (1x) Source: Disk, message: The device \Device\Harddisk2\DR2 has a bad block (2x) The security logs show nothing related. Also, when attempting to configure it from UBCD (utility: HDAT2), I get an error along the lines of "can't edit partition information" or something to that tune.

    Read the article

  • No Outbound Internet on Windows Home Server

    - by Kyle B.
    Could someone provide some steps for me to check my internet connection on my Windows Home Server? It seems to have intermittent connectivity issues and I am unsure of how to diagnose the problem because it is a headless (no monitor, no keyboard) machine so the only way to get to the device is via remote desktop (which works fine). When connected to the machine, it doesn't pull up any microsoft.com sites and some other sites it does pull up (i.e. gmail.com) and some it doesn't (stackoverflow.com). To make matters more complicated, it has worked intermittently in the past for reasons unknown. Are there tools I can use to properly diagnose the reason for the connection failure? I can ping 127.0.0.1 just fine, I have internet working on my other router-connected machines, so I'm not sure why this one would fail. Any suggestions would be much appreciated and up-voted :) ** edit - thanks for suggestions guys, I'm going to try these tonight and will update my post. ** edit #2 - I hoping this is a more permanant fix, but I have both changed my port on the router as well as restarted the router at the same time. The internet (for the moment) appears to be working. I will be sure to try everything we have discussed should this problem persist. Thanks, Kyle

    Read the article

  • Ubuntu 11.10 Virtual-box Unity 3D not working

    - by naveen
    After struggling for four hours, I still cannot get Unity 3D of Gnome 3 to work on my VirtualBox - I have been pouring through Internet and forum posts but to no avail. Here's what I've done so far: VirtualBox 4.1.4r74921 on Windows 7 Installed Ubuntu Desktop 11.10 ( 32 bit ) Enabled 3D acceleration Allocated 1.5GB of RAM Allocated 50MB video memory (hope this is not the culprit) Installed Guest edition 4.1.4 Did apt-get update and apt-get upgrade Booted back in to Ubuntu - falls back to Unity 2D Shared folder, mouse integration all works, so guest edition is properly installed Tried the command and below is the output /usr/lib/nux/unity_support_test –p OpenGL vendor string: Mesa Project OpenGL renderer string: Software Rasterizer OpenGL version string: 2.1 Mesa 7.11 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: no GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no I am trying to find what the "no" means but cannot find any good answers. Inter Core i5 processor 4GB of RAM on the host Display adapter: NVIDIA GeForce 8400GS Is anyone else facing the same problem? If so, can you point me to a solution or any reference where I can find a solution?

    Read the article

  • Can I have a single solid state drive and a RAID array on the same machine?

    - by jaminto
    Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

    Read the article

  • Dual Monitor support rdp 7 to win 7 on esxi

    - by rphilli5
    I am trying to RDP from a Windows 7 Professional dual monitor physical machine to a Windows 7 Professional VM hosted on esxi 4.0. I can get the spanning option to work to both monitors, but I have tried 3 different methods of connecting but have not been able to use true multiple monitors. At different times, I tried checking the "use all monitors" option, command line mstsc /multimon and added the line use multimon:i:1 to the .rdp file. None of these worked. Any ideas? The physical machine can connect to other Windows 7 physical machines with true multi monitor access. I also have the same issue when going from a 32bit RC1 machine to a Windows 7 Professional x64, but not when going in the reverse direction. Here's the .rdp: screen mode id:i:2 use multimon:i:1 desktopwidth:i:1440 desktopheight:i:900 session bpp:i:16 winposstr:s:0,1,341,118,1139,568 compression:i:1 keyboardhook:i:2 audiocapturemode:i:0 videoplaybackmode:i:1 connection type:i:1 displayconnectionbar:i:1 disable wallpaper:i:1 allow font smoothing:i:0 allow desktop composition:i:0 disable full window drag:i:1 disable menu anims:i:1 disable themes:i:1 disable cursor setting:i:0 bitmapcachepersistenable:i:1 full address:s:192.168.1.5 audiomode:i:0 redirectprinters:i:1 redirectcomports:i:0 redirectsmartcards:i:1 redirectclipboard:i:1 redirectposdevices:i:0 redirectdirectx:i:1 autoreconnection enabled:i:1 authentication level:i:2 prompt for credentials:i:0 negotiate security layer:i:1 remoteapplicationmode:i:0 alternate shell:s: shell working directory:s: gatewayhostname:s: gatewayusagemethod:i:4 gatewaycredentialssource:i:4 gatewayprofileusagemethod:i:0 promptcredentialonce:i:1 use redirection server name:i:0 drivestoredirect:s:

    Read the article

< Previous Page | 555 556 557 558 559 560 561 562 563 564 565 566  | Next Page >