Search Results

Search found 2123 results on 85 pages for 'crossover cable'.

Page 56/85 | < Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >

• linksys wap54g default wpa wireless key?

  - by jack

  Hi I wrongly pressed the push button in linksys wap54g web administration. Then it restarted and stated that it's protected with WPA while I first configured it as WEP. So, my old key didn't work. What should I do? Plugin with wire cable to reconfigure it? - which is the only way? coz it was embedded in ceiling. I found no solutions in product manual and google. Thank you.

  Read the article

• Multiple SSIDs better or worse

  - by swiss196

  I'm just setting up a network in a student house with 10 rooms, 3 floors. Configuration at the moment is as follows: Virgin Media 100mb Cable Virgin SuperHub on ground floor broadcasting on SSID1 Second AP(Edimax) wired on middle floor broadcasting on SSID2 These two networks server all 3 floors fairly well but I was wondering whether it would be better to setup an individual SSID for each floor (both the routers allow me to configure up to 3 ssids on each!). Would this help with speed issues, i.e if someone on the top floor is downloading/streaming etc, this wouldn't affect someone on the middle floor on a different SSID Or, will it have no effect? Thanks, Dave

  Read the article

• Serial converter - cat /dev/ttyUSB0 hangs on open

  - by Alex

  I am using Ubuntu 11.04 and attached a Garmin data cable. The device gets recognized [17718.502138] USB Serial support registered for pl2303 [17718.502181] pl2303 2-1:1.0: pl2303 converter detected [17718.513416] usb 2-1: pl2303 converter now attached to ttyUSB0 [17718.513443] usbcore: registered new interface driver pl2303 [17718.513446] pl2303: Prolific PL2303 USB to serial adaptor driver ... but when I do a strace cat /dev/ttyUSB0 it hangs on the open part and does not continue any more open("/dev/ttyUSB0", O_RDONLY|O_LARGEFILEC If I do the same on Ubuntu 12.04 it stops on fread(" ... ") which is okay, as there is currently no data comming in at this port. I am not sure if it is just a different configuration of the system or an driver related problem. How can I track this down further? Unfortunately I can not update the old Ubuntu 11.04 system for different reasons at the moment.

  Read the article

• One quarter of screen corrupted on MacBook Pro

  - by danyal

  I have a problem with my MacBook Pro's screen - here's a video: http://yfrog.com/4wm63z For those who prefer words, if you divide the screen vertically into 4 columns, the second column is corrupted (flickering, and discoloured, usually with yellow). I took it to an Apple store and they said it could be the screen or the logic board, neither of which will be cheap to replace. However, occasionally this problem will completely go away. So before I part with my cash, or decide to turn this into an overpriced media center for my TV... could the problem be a loose cable, or something else cheaper to fix?

  Read the article

• ATI Radeon 5850 I cant seem to get 3 monitors up at the same time. 2 Monitors and a HDTV but still.

  - by Jan

  Ive just bought the top end ATI Radeon card with 2 normal monitor ports and a HDMI. The idea was to continue using my dual screen setup as always and to use the last plug, the HDMI on my TV. I got a new 52 inch HD TV with all the necessary bits. This should work fine. But.. in Display Properties I still get only my 2 monitors up as options. Not the Digital TV. When I unplug 1 monitor and restart the computer, I get the TV and the other monitor. But never all 3 at the same time. Why is this ? Where can I go to tell it that I need all 3 screens at the same time. Also I get a message saying my gfx card also gives sound through the HDMI cable.. But the TV tells me its recieving a sound format that it does not understand. Any ideas on that too while were at it ?

  Read the article

• LAN access via USB from Ipod Touch?

  - by Alec

  I need to browse the local web server from my Ipod Touch to test apps we're developing. I'm not allowed to install a separate wireless access point which would be the easiest solution. Can I use the USB cable for this? Also, the local PC is a Dell Mini 9 running Ubuntu. Has anyone managed to use the wireless port to create an ad hoc connection to an Ipod Touch so the Ipod can browse the Ubuntu web server? This would be an alternate option for me. Thank you!

  Read the article

• setting up an access point from laptop to provide internet

  - by Avo

  i am trying to connect my wireless router as an access point from my laptop. the scenario is as follows: i have a wireless broadband connection at home, which i connect to using a username and a password. this username and password is unique, and can be used by one computer at a time!.. my sister and i can't have internet both at the same time! so im trying to connect my wireless router to my laptop with a physical cable so that i can provide internet via WiFi... first off, is this possible?!.. if not, what are my options? if it is possible, how do i set it up? a link to the appropriate steps would do as well, but i need it :(... thank you in advance, /av

  Read the article

• How to make phone calls using a pc, modem, headphone and no actual phone instrument

  - by user18151

  Hi, I have a phone landline connection and I DO NOT have a phone instrument. I connect the cable into my laptop, and want to make calls using my laptop. I have an HDA CX20561 modem. I seem to be able to dial number using dialer.exe, though nothing seems to happen. From Microsoft kb http://support.microsoft.com/kb/958143, it looks like dialer.exe alone is not enough for the call. Can somebody tell me how to make and receive phone call with whatever hardware I have, i.e. what software will I need. Thanks.

  Read the article

• Why does MTP work on one machine, but not another?

  - by bobmcn

  I have two Dell computers, a laptop and a desktop. I reinstalled Windows XP home on both, from the same CD. Then I installed Service pack 3 and ran windows update. When I connect my Creative Zen media player to the desktop, the MTP software that is part of XP recognizes it, and I can copy file to and from it using Windows Explorer. But when I connect the same player with the same cable to the laptop, I can see it in Windows Explorer, but none of the folders that are visible via the desktop are available, and I can't copy anything to or from it. How can I get this working on the laptop?

  Read the article

• How to kill volume when headphones pulled out

  - by wonea

  I often use headphones in order to listen to music in work time. However my chair tends to occasionally have the tendency to yank the headphone cable from my laptop. Now with my Android phone this wouldn't be a problem as the music will automatically stop playing. However, Windows does not kill the volume and instead re-routes the sound to my laptop internal speaker system. Aside from turning off my laptop speakers - is there a small utility available which serves my purpose of killing the volume so my work associates aren't inflicted with erroneous musical tastes?

  Read the article

• Some notebooks can connect to internet via certain wireless router, some can't

  - by Nathaniel

  I take a class in the building of a business and we sometimes use their internet via Wi-Fi. In the last few weeks, though, some notebooks haven't been able to connect to the internet even though they are connected to the router. It affected first a few of us and then all of us. Last week I tweaked around the network settings on the router (yes, the admin password is the same as the network key) and even moved the internet cable on the router from port 1 to the internet port. None of this really worked so I put things more or less back as I found them and alerted someone that someone who knew more than me had better have a look at the router. So, I don't know if anybody has had a look at it but now 2 of us can again connect to the internet. I had a look at the router settings last week and I really couldn't see what might be creating this issue. What might be the problem?

  Read the article

• Recover data from phyiscally damaged harddrive. What are my options?

  - by Michael Kniskern

  I was trying to replace the power supply in my desktop PC and ended up physically damaging the data connection from the hard drive to the motherboard. The plastic shelf for the copper prongs on the hard drive broke into the cable. Here is a picture of my handy work: Picture of damage I went to Best Buy Geek Squad to discuss my options and they said that they will need to send it to the recover center it could cost anywhere between $250 to $1600 USD to recover the data out the hard drive Is this reasonable for data recovery from a phyiscally damaged hard drive? Are there any other options I can explore? I am going to talk to the data doctors to see what my options are.

  Read the article

• Can / how to install openSUSE as a GUI-less home server with only wifi?

  - by Dougal

  Hello there, I'm following an article to set up openSUSE as a commandline server (http://www.howtoforge.com/perfect-server-opensuse-11.1). It seems to only work for wired internet connections. Is there any way to install openSUSE as a commandline server in my home network but using a wifi internet connection? Preferably from the get-go and not simply installing with LAN cable internet and then installing some wifi things later. Or, perhaps, to rephrase the question "How can I get the openSUSE install / post-install procedure to recognize my wifi internet connection?" Kind regards, Dougal

  Read the article

• Cannot boot from a hard drive

  - by Martin Melka

  I have a problem booting from a hdd. I used to have it as my main drive before I bought an SSD, so I had been able to boot from it. But for some reason, now, half a year later, I can't get it to work. I completely erased it, deleting data and partitioning (using EASEUS Partition Master), then I installed Kubuntu (without changing anything in the installer), but it simply won't boot up. It always boots the drive with Windows and when I unplug this drive, it only gives me an error "PXE-E61: Media test failure, check cable", I guess it's trying to boot from LAN. I tried installing the system on a freshly deleted drive, without any other drives plugged in the pc, but the problems persist. This is how the drives look now (first one has Windows 7 installed, the second one Kubuntu): I am lost. I mean, after doing a fresh wipe and a clean install without altering anything, it should work. But it doesn't. What can be wrong here? Thanks

  Read the article

• Coldfusion server VERY slow page loads

  - by Kevin

  I inherited a windows server 2003 coldfusion 7 server a few weeks ago. Today a network cable was unplugged by accident from the server. On plugging it back in, pages were NOT loading at all. Rather, we were receiving a generic coldfusion error page. After restarting IIS several times and coldfusion even more than that, we finally got pages to start loading. However, the loading is extremely slow (30+ seconds) on pages that used to load instantly. Loading through the local network (IE localhost/cfide/administrator) does nothing to help the load speed. I am not familiar with IIS or Coldfusion (We're in the process of migrating this to Linux/PHP), so this is all new territory to me. I'm hoping someone may have experienced this issue in the past and can help me solve it. I'm happy to provide any additional information that might be necessary....I'm just not sure what information you might need in order to help. Thanks for your time.

  Read the article

• Odd internet packet routing

  - by NachoChip

  I want to know is there anyway to explicitly control the packet routing. I try to connect my computer in HK from San Francisco. It is extremely slow and I use tracert to see what is going on. It seems the packet get routed from HK to Europe and then to New York and then to San Francisco. In US, I am using Astound Cable. Is there any suggestion I can force the packet to not go around the world before it reach my computer? Or it is all ISP dependent?

  Read the article

• Presentation software requires admin rights to install - any way to remove this requirement?

  - by James F

  I have some wireless presentation software which I use in a meeting room in order to allow end users to hold presentations here and wirelessly have their laptop screens showing on the TV on the wall. Unfortunately the .exe file requires admin rights to install therefore requiring that either the user requests temporary admin rights beforehand, I install it using my admin account or that we use a VGA/HDMI cable. Is there a way to remove the admin right requirement from a .exe or a .msi file so that it can be installed freely by any user? We are using XP for now but will be moving to 7 soon. Thanks James

  Read the article

• No sound through DisplayPort

  - by Chris Koknat

  I'm trying to connect my Elitebook 8440p laptop to my Samsung HDTV. The laptop does not have a HDMI connection, but it does have DisplayPort. I bought a DisplayPort-to-HDMI adapter here http://www.amazon.com/gp/product/B002CSRFD8/ref=oss_product, and connected it with a 3' HDMI cable. The video shows up fine, but there is no audio. DisplayPort, HDMI, and the adapter all support audio. I contacted HP tech support, who told me to update my sound drivers. I installed the driver and rebooted. Supposedly, I should see a "HD Audio" tab. No luck, even after installing the driver again and rebooting. HP closed the case. I'm using XP Pro.

  Read the article

• fstab line for auto mount drive that all users can read/write

  - by evilblender

  I have installed a cable that connects from the CPU's SATA motherboard connection to a removable drives' ESATA connection. I would like to be able to swap drives on the ESATA connection and have all users be able to read and write to these drives. I have created the directory /archive/ where I would like the drive(s) to mount. The drives are all formatted Fat 32 - but in the future I may use HFS for formatting. When I used the command (as root): mount /dev/sdc1 /archive the drive was mounted (but read only) What can I use in my /etc/fstab file that will allow drives to be mounted and unmounted by all users on the system? (both reading and writing) Also, will I be able to mount and unmount these drives without shutting down? or will I need to reboot every time I want to change drives? Thank you. Jeff

  Read the article

• GPO: Disable WiFi when computer is connected to LAN with wire

  - by r0ca

  Hi all! Is anyone of you know how to disable, thru a GPO, the Wireless connection as soon as the computer is connected to the LAN with a wire. By example, a user is at home with his laptop, connected to his home wifi connection. He leaves and comes to the office but the Wifi is still enabled. He plugs the ethernet cable in the computer and then, both wifi and wire connection are enable. I would like to apply a GPO that does this... Thanks a bunch!

  Read the article

• VGA no signal on LCD monitor attached to laptop

  - by Paul

  I bought a new Asus vh242h LCD monitor for use with my lenevo T60 laptop running XP professional. Display info under control panel says "Intel(R) 945GM Express Chipset Family". I am connecting via VGA. When I connect the monitor I get "VGA no signal" and the monitor screen stays blank. I have selected the monitor as the display device on the laptop. The information on the monitor displays the correct screen resolution from the laptop, so the monitor is communicating in some way with the laptop. I've successfully tried the monitor with my Dell inspirion 1525 running Windows Vista. I've change the VGA cable to one I know works. Tried different resolutions. I cannot find and specific drivers on the internet for this monitor, so I assume it should work with Plug and Play. Does anyone know what the problem could be?

  Read the article

• How to increase Remote Desktop resolution?

  - by BugAlert

  I'm using Windows 7 on a PC and connect to it via Remote Desktop Connection for Mac by MS, using a Mac. On the Mac, I have a 27" Display with 2560 x 1440 px resolution. The PC has a high performance graphics card (one of those that needs an additional power supply). Both machines are connected via network cable to a router. So network should be insanely fast. However, the max resolution I can get is 1400 x 1050. The PC just has a old and bad 21" monitor connected to it. How can I increase the resolution to 2560 x 1440 to work fullscreen with the Apple LED Cinema Display via Remote Desktop? Maybe I shouldn't even ask, because I already experience some lag at the low resolution of 1400 x 1050. But I guess this can be resolved as well?

  Read the article

• 2wire modem to linksys router

  - by Imajica666

  I want to hook a Linksys router to my 2wire modem/router (2701HG-b) to share my Internet connection. I ran from an open port from the 2wire to the WAN port of the Linksys but it will not work. I did this before with my cable modem to a router to my Linksys router. It worked then but not now. I read I can turn the 2 wire into a modem only but I need the 2wire wireless access also. IPCONFIG /ALL sees the 2wire with IP info as well as DHCP server/gateway. Any ideas?

  Read the article

• My Graphics Card isn't working Properly

  - by Dan

  I have just upgraded from a Sapphire AMD 6670 2gb Graphics card to a Nvidia GTX 650 ti 2gb SSC and my Windows Experiance index has gone from 6.8 to 7.7 but when playing games i am seeing no improvements i cannot play saints row three on even the lowest settings but according to many people and benchmarks on the web i should be able to play it comfortably. I want to know why this is happening to me..... I have installed the latest drivers and i have direct 10 + 11 installed I am 15 and it's my birthday today as i got it as a present but its not doing what i want also in am using a dvi cable not hdmi because i need a new one and its in the post. Is it possible that using dvi will affect performance

  Read the article

• Artefacts during HDV capture

  - by Jakub Konecki

  When I try to capture HDV video stream from a Canon HV20 camera to a Dell Studio 1558 (Intel i7 720qm) laptop running Win 7 Home Premium x64, the image appears with a very annoying noise - it contains block artefacts. Something is wrong with the Fire Wire controller (Ricoh 1304 OHCI host controller, build-in). Tried changing the driver to legacy one to no avail. This does not happen with DV stream. I'm using a Belkin cable. The capture works OK on another machine.

  Read the article

< Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >