Search Results

Search found 11914 results on 477 pages for 'networking architecture'.

Page 56/477 | < Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >

  • High number of ethernet errors. Tool for testing the ethernet card?

    - by Fabio Dalla Libera
    I have an Asus Sabertooth X79. I often get corrupted files. I checked the RAM, but memtest finds no errors. To avoid the possibility of disk errors, I tried copying the files to tmpfs. If I copy from the network, I get md5sum mismatches about once every 10 times using a 6Gb file. Copying from RAM to RAM, I didn't get mismatches. I get a very high number of errors in ifconfig (compared to others PCs I just took as reference, which have 0 with much more traffic). Here is an example RX packets:13972848 errors:200 dropped:0 overruns:0 frame:101 The motherboard is new, but do you think there're some problems with it? What could I use to test the (integrated) network adapter? What else do you think I should double check? --edit-- I tried another NIC, it gives a lot of Corrupted MAC on Input. Disconnecting: Packet corrupt lost connection. I noticed that another PC downloads at 11.1MB/s without problems. This pc at 66.0 MB/s. Is there any way to try to limit the speed?

    Read the article

  • Can't ping Ubuntu laptop from my LAN

    - by oskar
    My laptop has Ubuntu 10.10 and is connected to my router with full internet access, yet I can't ping it from other computers on my LAN. I tried the following: I can successfully ping those other computers from my Ubuntu laptop, so I didn't accidentally connect to someone else's network. I can successfully ping my Ubuntu laptop from itself, though I don't know if that means anything. I haven't messed with iptables at all, so it currently doesn't have any rules set that would cause it to reject anything. I made a DHCP reservation for my laptop's MAC address in my router to make sure I was always using the correct IP address. Please note that I am using a "command line only" install of Ubuntu, so I can't use any GUI network config tools. The reason I want to ping it is because I am trying to run an NFS server on the laptop, yet despite correctly setting it up I cannot access the NFS volume on another computer because it isn't even visible on the network right now.

    Read the article

  • Wifi hotspot to connect to Android using non-AP supported cards

    - by 3l4ng
    I'm running Ubuntu 13.10 64b on a Dell Inspiron N5010. My wireless device (found using lspci) is Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01). I bought a new android phone and want to connect to Internet by using the laptop as a Wireless Access Point (ad-hoc doesn't work with Android). I tried following tutorials like the one at How to setup a wi-fi hotspot (access point mode)?. The relevant output from iw list was Supported interface modes: * IBSS * managed Running sudo hostapd /path/to/conf/file gave me (eth1 is the wireless, verified by iwconfig) Failed to create interface mon.eth1: -95 (Operation not supported) Could not set channel for kernel driver eth1: Unable to setup interface. Could not connect to kernel driver. I am able to use Connectify and Virtualrouter on Windows, and the phone works great. How do I get an access point running on Ubuntu? I'm open to other alternatives as well.

    Read the article

  • Skipping video and audio with PS3MediaServer

    - by MaxMackie
    I'm using the latest PS3MediaServer build right from the repos suggested in the Ubuntu Wiki. I'm streaming multiple movies from my server (Ubuntu 10.04 LTS) to my PS3 over wireless. Sometimes, during some movies, the audio and the video will begin skipping. This can last anywhere between 5 and 30 seconds before it goes back to normal. I have a four core i5 processor and 8GB of DDR3 RAM so I don't think my computer is having a hard time keeping up with the transcoding. So this leads me to believe it's either sub-optimal transcoding options from within PS3MS or my network can't handle the heat. Other than the out-of-box configuration, is there any way I can tweak the settings for the application to use my resources more efficiently?

    Read the article

  • What is the structure of network managers system-connections files?

    - by Oyks Livede
    could anyone list the complete structure of the configuration files, which network manager stores for known networks in /etc/NetworkManager/system-connections for known networks? Sample (filename askUbuntu): [connection] id=askUbuntu uuid=81255b2e-bdf1-4bdb-b6f5-b94ef16550cd type=802-11-wireless [802-11-wireless] ssid=askUbuntu mode=infrastructure mac-address=00:08:CA:E6:76:D8 [ipv6] method=auto [ipv4] method=auto I would like to create some of them by my own using a script. However, before doing so I would like to know every possible option. Furthermore, this structure seems somehow to resemble the information you can get using the dbus for active connections. dbus-send --system --print-reply \ --dest=org.freedesktop.NetworkManager \ "$active_setting_path" \ # /org/freedesktop/NetworkManager/Settings/2 org.freedesktop.NetworkManager.Settings.Connection.GetSettings Will tell you: array [ dict entry( string "802-11-wireless" array [ dict entry( string "ssid" variant array of bytes "askUbuntu" ) dict entry( string "mode" variant string "infrastructure" ) dict entry( string "mac-address" variant array of bytes [ 00 08 ca e6 76 d8 ] ) dict entry( string "seen-bssids" variant array [ string "02:1A:11:F8:C5:64" string "02:1A:11:FD:1F:EA" ] ) ] ) dict entry( string "connection" array [ dict entry( string "id" variant string "askUbuntu" ) dict entry( string "uuid" variant string "81255b2e-bdf1-4bdb-b6f5-b94ef16550cd" ) dict entry( string "timestamp" variant uint64 1383146668 ) dict entry( string "type" variant string "802-11-wireless" ) ] ) dict entry( string "ipv4" array [ dict entry( string "addresses" variant array [ ] ) dict entry( string "dns" variant array [ ] ) dict entry( string "method" variant string "auto" ) dict entry( string "routes" variant array [ ] ) ] ) dict entry( string "ipv6" array [ dict entry( string "addresses" variant array [ ] ) dict entry( string "dns" variant array [ ] ) dict entry( string "method" variant string "auto" ) dict entry( string "routes" variant array [ ] ) ] ) ] I can create new setting files using the dbus (AddSettings() in /org/freedesktop/NetworkManager/Settings) passing this type of input, so explaining me this structure and telling me all possible options will also help. Afaik, this is a Dictionary{String, Dictionary{String, Variant}}. Will there be any difference creating config files directly or using the dbus?

    Read the article

  • Send arbitrary commands to modem for info

    - by mydoghasworms
    I have a USB 3G data card and modem. According to the supplier, to check the data balance on the account, I must dial a number like *89# (or whatever) from the handset. The device appears as a ppp0 interface in my network devices. How does one go about issuing commands to the modem to send the commands and receive back the information? UPDATE: OK, I found some help here: http://www.linuxquestions.org/questions/linux-hardware-18/sending-at-commands-to-a-sms-modem-372445/, but firstly, there are 3 ttyUSB devices on my system, and I assume that one of them is the 3G modem, but how can I tell? Secondly, trying to echo something to two of them says that the device is busy, which stands to reason, because I am using it to connect to the internet. Some help, please?

    Read the article

  • Wired Network not working on Ubuntu 11.10 + Strange Behavior with Manual Conf

    - by Mauricio Cruz
    I'm new to Ubuntu - to be honest this is my very first day trying it... and I've already spent hours trying to make my wired connection work. I've been using this wired network with Windows and OSX, and in both systems I also had some trouble trying to connect in the past (and the troubleshooters did their magic and helped me get connected). Today, this is what I got: I'm running Ubuntu 11.10; ifconfig: eth0 Link encap:Ethernet HWaddr 78:2b:cb:c3:bf:8f UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1 errors:0 dropped:0 overruns:0 frame:0 TX packets:343 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:70 (70.0 B) TX bytes:63273 (63.2 KB) Interrupt:20 Memory:e2e00000-e2e20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1859 errors:0 dropped:0 overruns:0 frame:0 TX packets:1859 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:149368 (149.3 KB) TX bytes:149368 (149.3 KB) wlan0 Link encap:Ethernet HWaddr 10:0b:a9:82:55:c0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:15484 errors:0 dropped:0 overruns:0 frame:0 TX packets:16871 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12048377 (12.0 MB) TX bytes:2677679 (2.6 MB) I also have some information from Windows ipconfig /all that I ran at my friend's machine Ipv6 Address: <address> preferential Ipv4 Address: 172.26.65.23 <preferential> Netmask: 255.255.254.0 Default Gateway: 172.26.64.1 DHCP Server : <address> DNS Servers : <address> DNS Suffix : <suffix> The weird thing is that I've tried to configure everything manually, using "Network Connections". When I add everything inside IPv4 Settings, the connection is finally successful, but only for 4~5 seconds before getting disconnected again... Update:I just changed the Connection Method to "Local-Link Only", and the same described above happens: At first, it says "Connection Stablished", but after a few seconds, the wired network gets disconnected. I hope someone can help me get connected! Thanks!

    Read the article

  • Internet problems

    - by user288636
    I have a strange problem. When I copy/paste via ethernet everything is working fine. But when I go to youtube or downloading some files via internet, connection is freezing very often. Just stop downloading and after few minutes continue and than again stop and etc... Could it be hardware problem with network card or motherboard (network is integrated on board)? I am using Ubuntu 14.04 but it happens on live cd distribution of Mint. There is no restrictions cose when I using on same switch my other laptop with linux installed everything working fine.

    Read the article

  • How to connect to DSL modem using PPPoE?

    - by VJo
    Hello, I am connecting to the internet through a pppoe connection, but for some reason I can not connect to my modem (it's address is 192.168.1.1). Before I set my pppoe connection, I could connect. So, is there a way? EDIT The output of ifconfig is : r@PlaviZec:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:13:d4:f7:02:d4 inet6 addr: fe80::213:d4ff:fef7:2d4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2811 errors:0 dropped:0 overruns:0 frame:0 TX packets:2801 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2538831 (2.5 MB) TX bytes:448591 (448.5 KB) Interrupt:21 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:28 errors:0 dropped:0 overruns:0 frame:0 TX packets:28 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1600 (1.6 KB) TX bytes:1600 (1.6 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:92.229.42.177 P-t-P:213.191.64.59 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:2794 errors:0 dropped:0 overruns:0 frame:0 TX packets:2741 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:2476277 (2.4 MB) TX bytes:381240 (381.2 KB)

    Read the article

  • Ethernet card not detected on Ubuntu Server 12.04

    - by Dana
    My onboard ethernet isn't detected after a re-install of Server 12.04. For reasons I won't get into here, I had to put the server's drive into another machine to install Ubuntu, then swap back into the server. So the server starts up fine, except for the "Waiting for network configuration". I read in another article that Server, by default, doesn't handle new mac addresses for hardware changes dynamically, unlike Ubuntu Desktop, but a look at /etc/udev/rules.d/70-persistent-net.rules shows only one ethernet interface. Shouldn't it show both the old, and the new? lspci -vv shows an ethernet interface, so what the heck is going on? I should mention that the onboard LAN is enabled in the BIOS. And I know this isn't important, but all this started when I changed some network configuration settings in webmin before the re-install. It couldn't download any updates, so I tinkered a little. Broke, it, installed FreeNAS, which worked, but I didn't like it, then went back to Ubuntu Server, and now I'm in this pickle. Thanks for any advice!

    Read the article

  • Can't connect to Wired Network after installing 12.04

    - by ezz9
    I have installed 12.04 into a used HP Compaq DC 7100 CMT. Plugged in LAN cable into the computer and it says network disconnected. from what I understand on the things I've read, it's not getting the address right, maybe it's just a guess (hardware address 00:16:35:78:47:bb). I know the LAN cable is working I can get on the net with the old computer. (Old computer is using device MAC address; Auto eth0 00:11:11:E6:4F:FE). I have put this address into the newer HP and it shows last used (minutes ago) but no Internet sever not found. I tried the hardware address it says never. I feel and think this should be easy to fix. But I just don't know. Here is the info everyone has asked for, but they never say what I should do. sudo lshw -C network; rfkill list; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; uname -a; ifconfig; route -n *-network description: ethernet interface product; NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:40:00.0 logical name: eth0 verson: 01 serial: 00:16:35:78:47:bb size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000-fd configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 duplex=full firmware=5751-v3.29a latency=0 link=yes multicast=yes port=twi sted pair speed=100Mbit/s resources: irq:17 memory:f0400000-f040ffff auto lo iface lo inet loopback DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION= "Ubuntu 12.04 LTS" 00:00.0 host bridge [0600]: Inter Corporation 82915G/P/GV/GL/PL/910GL Memory Con troller Hub [8086:2580] (rev 04) 00.02.0 VGA compatible controller [0300]: Intel Corporation 82915G/GV/910GL inte grated Graphics Controller [8086:2582] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 [8086:2662] (rev 03) 00:1d.0 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #1 [8086:2658] (rev 03) 00:1d.1 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #2 [8086:2659] (rev 03) 00:1d.2 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #3 [8086:265a] (rev 03) 00:1d.3 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #4 [8086:265b] (rev 03) 00:1d.7 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB2 UHCI Controller [8086:265c] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI bridge [8086:244e] (rev d 3) 00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/ FRW (ICH6 Family) AC'97 Autio conrtroller [8086:266e] (rev 03) 00:1f.0 ISA bridge [0601]: Intel Corporation 82801FB/RF (ICH6/ICH6R) LPC Interfa ce Bridge [8086:2640] (rev 03) 00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 fami ly) IDE Controller [8086:266f] (rev 03) 00:1f.2 IDE interface [0101]: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Con troller [8086:2651] (rev 03) 40:00.0 Ethernet controller [0200]: Broadcom Corporation NetXreme BCM5751 Gigab it Ethernet PCI Express [14e4:1677} (rev 01) Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Linux bob-desktop 3.2.0-23-generic-pae #36-Ubuntu SMP Tpr 10 22:19:09 UTC 20 12 i686 i686 i386 GNU/Linux eth0 Link encap:Ethernet HWaddr 00:16:35:78:47:bb inet6 addr: fe80::216:35ff:47bb/64 Scope:link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2517 errors:0 dropped:0 overruns:0 frame:0 TX packets:164 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164508 (164.5 KB) TX bytes: 40884 (40.0 KB) Interrupt:17 lo Link encap:Local loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3290 errors:0 dropped:0 overruns:0 frame:0 TX packets:3290 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen: 0 RX bytes:267212 (267.2 KB) TX bytes: 267212 (267.2 KB) Kernel Ip routing table Destination Gateway Genmask Flags Metric Ref Use Iface ran this sudo dhclient eth0 no reply ran this ip addr 1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST ,MULTICAST ,UP ,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/enter 00:16:35:78:47:BB brd ff:ff:ff:ff:ff:ff inet 169.254.7.172/16 brd 169.254.255.255 scope link eth0:avahi inet6 fe80::216:35ff:fe78:47bb/64 scope link valid_lft forever preferred_lft forever Help please.

    Read the article

  • How to prevent a hacked-server from spoofing a master server?

    - by Cody Smith
    I wish to setup a room-based multilayer game model where players may host matches and serve as host (IE the server with authoritative power). I wish to host a master server which tracks player's items, rank, cash, exp, etc. In such a model, how can I prevent someone that is hosting a game (with a modified server) from spoofing the master server with invalid match results, thus gaining exp, money or rankings. Thanks. -Cody

    Read the article

  • how can i bridge my LAN port to batman-adv?

    - by rubo77
    On Ubuntu 12.04 I have my Laptop connected to and part of a batman network. So my Laptop is meshing with the net. The script I used is this How can I install a bridge, that will allow another host laptop to get internet through my Laptop? I tried this: service network-manager stop batctl if add eth0 apt-get install bridge-utils I added this in /etc/network/interfaces auto br0 iface br0 inet static address 10.116.123.123 bridge_ports eth0 bridge_fd 5 bridge_stp no then ifconfig sais br0 Link encap:Ethernet Hardware Adresse 00:a0:d1:a9:db:da rubo78: inet Adresse:10.116.123.123 Bcast:0.0.0.0 Maske:255.255.255.255 bat0 Link encap:Ethernet Hardware Adresse 6e:8a:8f:f2:82:e3 inet Adresse:10.116.2.250 Bcast:10.116.255.255 Maske:255.255.0.0 ifup br0 batctl if eth0: active wlan0: active but I get no network on the host

    Read the article

  • Setting up shared connection

    - by Calvin Froedge
    I have a network that is connected to the internet via a switch connected to a router. I have it setup like this so I can work on the new network without causing problems on the old. Anyway, I'm trying to enable internet connection sharing. Internet comes to server like this: Modem - Router - Switch - Ubuntu 11.10 (Eth0) I want to share the connection through Eth1 (Eth1 - Managed Switch - Clients). Here is my config for /etc/network/interfaces: I have a DHCP server running on Eth1. Here is my config: ddns-update-style none; option domain-name "myserver.local"; option domain-name-servers 192.168.1.2, 8.8.8.8; default-lease-time 600; max-lease-time 7200; authoritative; subnet 192.168.1.0 netmask 255.255.255.0 { interface eth1; range 192.168.1.3 192.168.1.254; option routers 192.168.1.1; option subnet-mask 255.255.255.0; option broadcast-address 192.168.1.255; } Here is /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp #Used for internal network auto eth1 iface eth1 inet static address 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 Here is /etc/hosts: 127.0.0.1 localhost 127.0.1.1 myserver.isp.com server 192.168.1.2 server.myserver.local server myserver.local In /etc/sysctl.conf, I've set the following: net.ipv4.ip_forward=1 Finally, in /etc/rc.local, I've set the following: /sbin/iptables -P FORWARD ACCEPT /sbin/iptables --table nat -A POSTROUTING -o eth1 -j MASQUERADE When I ping 8.8.8.8 (google's DNS) from a client that is authenticated with my DHCP server (they have been assigned a local ip, like 192.168.1.10), I get a timeout. How can I debug this further to figure out where my problem is?

    Read the article

  • wifi problems with lenovo g580 on kubuntu-13.04-desktop-amd64

    - by user203963
    i have a wifi connection problem in lenovo g580 on kubuntu-13.04-desktop-amd64. ethernet cable is working properly but wifi does'nt connect below are some hardware information sudo lshw -class network gives *-network description: Ethernet interface product: AR8162 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:89:84:3d:e9:10 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm pciexpress msi msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=alx driverversion=1.2.3 duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:90500000-9053ffff ioport:2000(size=128) *-network description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=bcma-pci-bridge latency=0 resources: irq:17 memory:90400000-90403fff *-network description: Wireless interface physical id: 3 logical name: wlan0 serial: 68:94:23:fa:2c:d9 capabilities: ethernet physical wireless configuration: broadcast=yes driver=brcmsmac driverversion=3.8.0-19-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bgn lsubs gives Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0489:e032 Foxconn / Hon Hai Bus 002 Device 003: ID 04f2:b2e2 Chicony Electronics Co., Ltd lspci gives 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) 01:00.0 Ethernet controller: Qualcomm Atheros AR8162 Fast Ethernet (rev 10) 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Does anyone knows the solution? rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: yes Hard blocked: no 2: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 3: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no

    Read the article

  • Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

    - by Lucas
    I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

    Read the article

  • Is it possible to write a program that pipes the sound from one computer through the sound card of another?

    - by Kenneth
    I have a case where I need to use one computer's sound card to play sound but I want the sound to be generated at another computer that's on the same network as the other. Ideally the program that does this would only run on the computer that was generating the sound, though I'm fairly certain that isn't possible based on the research I have been doing. What ever I do with it though the solution would need to be such that the computer actually playing the sound would be secure. Thanks for any input.

    Read the article

  • DSL connection not working in 10.04

    - by Mussnoon
    I use a wired PPPoE connection to connect to the Internet. What I need to do on Windows to connect to it is put in static IP address, gateway, subnet mask and DNS servers for my LAN card. Next I have to create a dialer for a PPPoE connection, put in my user name, the service name and the password, and "dial" this connection. And it works fine. On Ubuntu 10.04, however, I have tried setting things up in a similar fashion - put in all static addresses for the "automatic" wired connection, then put in user name, service name, password for a "DSL" connection. It worked for a while, then stopped. I have tried putting in all the details within the DSL configuration dialog, same thing happened - it worked for a while, then stopped. I have tried deleting the ethernet connection and only keeping the DSL one with all the numbers put in place, same thing happened - it worked for a while, then stopped. Each of the times, when it connected, it connected randomly, after trying a few times, and either stopped working within a few minutes, or after I had rebooted. I have deleted and remade the connection dozens of times - even with different names, but nothing seems to be working. I have also tried pppoeconf from the terminal, didn't work. I have checked /var/log/kern.log, but nothing changes in the file when I try to connect. I have also checked /sbin/route, but gedit can't even open it (says it can't figure the character encoding...). The "connection established" notification pops up from the top right corner, the same way as when the computer is actually connected to a network. Can anyone figure what's wrong and how it can be solved?

    Read the article

  • Huawei E3276 LTE uplink slow in the routing Ubuntu, but not with other devices in the LAN

    - by Mytomi
    I have a Huawei E3276 LTE dongle (12d1:14fe - 12d1:1506) and a problem with the upstream speed. The problem is not only present with Ubuntu 14.04 LTS (64 bit workstation, kernel 3.16), but also with Raspbian Jessie for Raspberry PI (kernel 3.14). Upstream seems to be always limited to 5 Mbit/s whenever I check the speed from the Linux computer that I use as a LTE router. The other computers in the LAN always get about 10-15 Mbit/s upstream, even though the traffic is routed through the same Linux computer suffering from seemingly capped uplink. Downstream speed is always fine, 25 Mbit/s. I even installed Windows 7 in the same computer as Ubuntu and the speeds are 25 Mbit/s down, 15 Mbit/s up. So the problem is not with E3276 device itself or in the mobile subscription, but in the Huawei E3276 Linux compatibility. Maybe something in the kernel? I have made sure that the matter is not with iptables rules: the speed does not noticeably increase when iptables is disabled. Turning off IPv4 forwarding does not improve speed either. I'm not sure what settings and logs do help in debugging the situation. Please ask for more details, if you have a clue what might be wrong. Thanks, Mytomi

    Read the article

  • Could anyone help me get my NETGEAR WNA3100 (Broadcom BCM43231) wireless adapter to work?

    - by Matthew Carroll
    I have just moved back to Ubuntu from Windows 7 and a few months ago, I bought a NETGEAR WNA3100 wireless adapter because my old adapter had broken. I plugged in my adapter and it doesn't seem to work, I also used the windows 7 drivers for it and tried them on the program "Windows Wireless Drivers" and they don't seem to recognize the device. However I have heard you need XP drivers but I can't seem to find them on the internet nor find them on the CD. Could anyone help me get my wireless adapter to work? Any help is greatly appreciate. P.S I do have internet connection though I have to tether my phone to my computer and then connect my phone to my router.

    Read the article

  • Good alternative to NetLimiter(windows) for ubuntu

    - by Harsh
    there is program NetLimiter for windows. while I was using windows it was very useful to me to find out the IP address of ther person who was downloading from me, or to know IP address of any person on lan who was using DC++ with some nick. and after that I can easily know the computer name of that person using nbtstat. I was wondering if there is any tool for ubuntu using which I an find out the IP address of person who is downloading from me or from whom I am downloading on lan. I am on university lan and we are using PtokaX and DC++ for file sharing on lan. people sometimes put some offencive stuff on open chat on DC++ using some Nick and I don't know how to trace them while I am using Ubuntu. Plz help.

    Read the article

  • Trouble installing Server 12.10 - Dead keyboard, Blank Screen, Network Config

    - by Mikey
    Installing 12.10 server from cd - minimal installation: basic system, ssh server,postgreSQL, manual updates. Hardware is brand new HP server that also runs Win 2003 Server Standard as a DNC excellently - I installed the grub boot manager on the primary partition and it is working fine - can boot to Win or Ubuntu without issue. Everything seemed to go OK on the installation - BUT when I restarted the system after install and booted to Ubuntu, I got the command prompt for Ubuntu, but the keyboard was UNREPSONSIVE - dead. There is nothing wrong with the keyboard - works fine if I boot to Win. With a completely unrepsonsive keyboard I had to hit the power switch - when I restarted and booted to Ubuntu, Ubuntu started but no command prompt came up at all - just black screen. I powered down and rebooted to advanced Ubuntu options - it tried to reinstall/initliaze a long list of packages - when it got to 'waiting for network configuration' it waited, then a message 'waiting 60 seconds for network configuration'... it waited 60 seconds and then I got a 'failed to configure network message' and it continued. Finally it finished, I hit enter and got to a prompt - but again, keyboard UNREPSONSIVE - dead. I went through this several times - tried 'repairing broken installation' option and also reinstalling entirely - always same results. I am flummoxed. The only clue I have is that for the Windows DNC config, the IP address is static - not via DHCP. But I don't think that should impact Ubuntu at all - perhaps I am mistaken. What is wrong?

    Read the article

  • How to protect a peer-to-peer network from inappropriate content?

    - by Mike
    I’m developing a simple peer-to-peer app in .Net which should enable users to share specific content (text and picture files). As I've learned with my last question, inappropriate content can “relatively” easily be identified / controlled in a centralized environment. But what about a peer-to-peer network, what are the best methods to protect a decentralized system from unwanted (illegal) content? At the moment I only see the following two methods: A protocol (a set of rules) defines what kind of data (e.g. only .txt and jpg-files, not bigger than 20KB etc.) can be shared over the p2p-network and all clients (peers) must implement this protocol. If a peer doesn’t, it gets blocked by other peers. Pro: easy to implement. Con: It’s not possible to define the perfect protocol (I think eMail-Spam filters have the same problem) Some kind of rating/reputation system must be implemented (similar to stackoverflow), so “bad guys” and inappropriate content can be identified / blocked by other users. Pro: Would be very accurate. Con: Would be slow and in my view technically very hard to implement. Are there other/better solutions? Any answer or comment is highly appreciated.

    Read the article

  • Wireless not detected on an hp Pavilion g6 - RT5390PCIe

    - by Earl Larson
    I just bought an HP Pavilion g6 laptop and I installed Natty Narwhal alongside Windows 7. In Windows 7, my WiFi works perfect but in Ubuntu it absolutely (no matter what I do) won't detect my home WiFi network. Here is the output of "lspci": earl@ubuntu:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200] 01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 03:00.0 Network controller: Ralink corp. Device 5390 04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01) earl@ubuntu:~$

    Read the article

  • Sharing internet to Ubuntu 12.04 VMWare guest

    - by John Cogan
    Got the 12.04 distro and installed this on my Mac VMWare Fusion (Version 4.1.2). Install went fine and Ubuntu seemed to update itself during the install. Rebooted and now I cannot get Ubuntu to access the internet via my Macs Ethernet connection (Connected to a router) Have tried settings the VMWare network adaptor to NAT or bridged and Host only without success. In Ubuntu I have the eth0 set to Automatic DHCP. VMWare tools is installed as well. I know next to nothing about what to do here and net searches on both Stackoverflow and Superuser sites are producing not results for me. Could someone please help? What to eventually have Ubuntu run in the background as a development web server running Zend Framework and CE Server edition but need thew internet access to run updates etc on Ubuntu. Any help would be really appreciated. TIA John

    Read the article

< Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >