Search Results

Search found 40031 results on 1602 pages for 'command message'.

Page 569/1602 | < Previous Page | 565 566 567 568 569 570 571 572 573 574 575 576  | Next Page >

• On a failing hard drive, I am able to view data but unable to copy it - why?

  - by Tom

  I have a 2.5" external hard drive that is failing. It's not making the expected 'clicking' noise that most hard drives and I am able to view the data, but I am unable to actually retrieve the data. I attempted to use SpinRite in order to access the data on the drive, but it didn't like the external drive. When I view the drive's property page, the drive shows that it's used space is at 100% and that it has 0 bytes available; however, the progress indicator under the drive icon in Windows Explorer shows that it's roughly 50% full (which is correct). When I attempt to run Windows' "Error Checking" tool and attempt to "scan for an attempt recovery of bad sectors," the tool begins to run then immediately closes with no error message. I am able to browse the contents of the drive using Windows Explorer. When I begin to try copying any given single file, the copy process begins, an indicator starts, and then the copy fails with no real error message. The Disk Management page in Computer Management under Control Panel also shows this drive has being 'Healthy.' I dropped the drive off at a data recovery store and they said that "The data seems to be intact, but an internal failure is preventing any information from being retrieved." They offered to provide me references to a data recovery specialist. I've also attempted to run CHKDSK on the drive (with and without arguments) but it returns the following error: The type of the filesystem is RAW. CHKDSK is not available for RAW drives. Before going the route of more expensive data recovery, I'm wondering if these symptoms sound familiar to anyone? Other questions... I'm willing to continue trying tools such as TestDisk and/or PhotoRec (as the majority of the data that I'd like to salvage are photos) but how long I should expect either tool to run given approximately 400GB of data? I'm also comfortable using Linux so I welcome any suggestions for utilities or tools and strategies with which you've had success.

  Read the article

• See former key sequences in vim

  - by Vasiliy Sharapov

  Sometimes I share screen shots and clips of vim usage with others. It would be nice to expand on the part of the status bar highlighted in this picture: I would like some way to make previous key sequences visible as well, such as: y2w jj f[ p 2d - You can see the key sequences leading up to the current one. I'll elaborate on my wish list at the bottom. Is something like this is available as a plugin or vim script? The sheer number of scripts available on vim online makes this hard to find by keyword. Some features I would hope for (but seem improbable): Delimit key sequences with a non-keyboard character instead of space, and a different one for the current command, so y2w jj f[ p 2d might become y2w¦jj¦f[¦p » 2d Replace keys that have a letter alternative with the alternative, such as the right arrow key - ^[[C with the equivalent l. Edit: To clarify, the right arrow key is a valid key in vim, but has no character to represent it, the l key preforms the same function and could/should substitute it. Have previous keystrokes run all the way to the beginning of the line (instead of just one or two), and just have vim's command prompt overwrite it when necessary. Replace some keystrokes with a more elegant alternative, for example hhhhh with 5h or more impressively d2f) with d% (in the appropriate situation).

  Read the article

• Linux machine can't find its tape drive

  - by Kyle Hodgson

  I have an older HP NetServer LPr with what is apparently a Symbios SCSI card connecting to a Quantum SuperLoader 3 that is DLT based. From time to time, we seem to lose the connection to the autoloader. It's usually due to flaky power, but not totally sure why; sometimes when this happens the Autoloader's LED's are orange and it needs to be power cycled. The annoying workaround currently is to reboot the machine. As it is our production VPN and DNS server in addition to being our backup server, this is less than optimal. In Debian (Sarge) is there not some command one can type to get the card to notice that it has the autoloader connected again? dcr1:/proc# grep -i symbios /proc/pci SCSI storage controller: LSI Logic / Symbios Logic 53c895 (rev 1). dcr1:/proc# uname -a Linux dcr1 2.4.27-3-686 #1 Tue Dec 5 21:03:54 UTC 2006 i686 GNU/Linux dcr1:/proc# mt status mt: /dev/tape: No such device dcr1:/proc# ls -l /dev/tape lrwxrwxrwx 1 root root 8 2007-02-07 16:01 /dev/tape -> /dev/st0 dcr1:/proc# That mt status command will show the actual st0 status when things are working correctly. The No such device message is usually the second clue that we need to reboot - the first clue is usually that the backups didn't run.

  Read the article

• Server reporting incorrect mime type for css files

  - by Becky

  We have a VPS server that we host our websites on. I have written a CMS using CodeIgniter. On one of the interfaces, I am attempting to upload a css file to the system. This worked correctly when we had it hosted on shared hosting. Since we've moved it to the VPS, I am getting an "incorrect filetype" error. It all comes down to the fact that the server is reporting a mime type of text/x-c for the css file rather than text/css. I logged in via shell and ran the following command on an existing valid css file (to make sure it wasn't an issue with either CodeIgniter or with php). file --brief --mime 'filename.css' 2>&1 The server gave me the following in response to my command: text/x-c; charset=us-ascii My question ... is there some sort of server setting that I need to tweak to get the server to correctly identify the css file as text/css? Do I just have to add a mime type for the css files to the server? I found the mime types file (etc/mime.types), and it just hase video types and a couple other that I have no idea what they are. There is nothing in there for css or images or html files. Unless I'm looking in the wrong spot. I'm not a server person, so I'm hoping someone can help me out. Some server specs: Apache/2.2.22 (Unix) php 5.3.13 Server API = CGI/FastCGI the fileinfo php extension appears to be disabled

  Read the article

• How does one change the UUID of a Volume on Mac OSX 10.6?

  - by Emmel

  Does anyone know how to change the UUID of a Volume? The background for this question is that I have a duplicate UUID issue: I have /Volumes/OldMacHD with a UUID of XYZ. I have /Volumes/Mirror1 with a UUID of XYZ (same UUID! I bet that's because OldMacHD USED to be part of this mirror). I got these UUIDs via 'diskutil info /dev/thatdisknumber | grep UUID'. I'd like to change the UUID of 'Mirror1'. I discovered by chance the 'hfs.util' utility, since these are HFS volumes after all. The man page for hfs.util says that if you issue the -s flag, this changes the UUID. However, if you type hfs.util all by itself, it doesn't show you the -s option at all, just every option besides that! Grr. I tried it anyway: sudo /System/Library/Filesystems/hfs.fs/hfs.util -s /dev/disk4 (the raid volume). Nothing happens. No error message, no success message. UUID exactly the same. I tried it while the volume was unmounted. Any ideas?

  Read the article

• emacs error: "Symbol's value as variable is void: hostname"

  - by Florian Pilz

  After I installed emacs this error occurs every time on startup. It prevents me from installing plugins, e.g. auctex via aptitude. I already tried to install a plugin by hand (rails for ruby), but doesn't work. The error doesn't contain the message "hostname", but the hostname of my PC is displayed ("bloodredangel-ubuntu"). I changed my hostname to "bloodredangel", but the error message stays the same. While I changed my hostname I saw that in /etc/hostname were two entries: 127.0.0.1 bloodredangel-ubuntu I already asked this question in an ubuntu forum but they couldn't help. They recognised an misconfigured /etc/hosts file, which I corrected, but from time to time these incorrect configurations get attached by something. I didn't add them by hand, maybe it has something to do with the issue. The misconfigurations looked like this: 127.0.0.1 127.0.0.1 bloodredangel-ubuntu localhost.localdomain localhost 127.0.0.1 127.0.0.1:8080 bloodredangel-ubuntu localhost.localdomain localhost I didn't found a solution on the internet, so I hope I will find help here finally.

  Read the article

• Accidentally deleting all OSX users using dscl

  - by gutch

  OK, so I just did something really stupid and deleted all the user accounts on an OSX 10.6.6 machine by running this: sudo dscl . -delete /users What I actually wanted to do was delete a single, troublesome account using a command like this: sudo dscl . -delete /users/localadmin ...but I absent-mindedly pressed return too early and deleted the lot. I've tried using -list and can confirm that I have indeed wiped all the accounts. The machine is currently running fine, but I'm sure that once I log out / reboot then it will be completely broken. I don't mind that I've deleted the normal user accounts (there was only one I wanted anyway). But it's surely going to be a big problem that system accounts like _installer and _jabber and _lda and _windowserver etc etc are gone. So my question is, how can I restore the standard set of system accounts? Do I have to reinstall OSX from scratch? Or can I either: undelete those system accounts, or run some command to recreate the system accounts?

  Read the article

• NTBackup Error: C: is not a valid drive

  - by Chris

  I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Switch Windows 8 from a hybrid MBR/GPT => GPT only on Macbook Pro Retina

  - by Sid

  I used DiskUtility+Bootcamp Wizard to setup my hard drive for Windows 8 (final MSDN). Somewhere in that process, the Apple tools turned my GPT disk into a hybrid MBR/GPT. All my 4 primary MBR partitions are used up, so when I try turning on Bitlocker in Windows 8, it complains about not finding a System drive. I know on Windows 8 the Bitlocker setup tries to create the 200(?)MB system partition if it's missing. However with all 4 partitions filled I suspect it can't create system drive = it can't find it = throws back an error like "BitLocker Setup could not find a target system drive. You may need to manually prepare your drive for BitLocker". I've already tried disabling hibernation, swap file etc. Now I'm thinking that if I were to get rid of the MBR scheme altogether, perhaps I can be alright within the GPT world without MBR's 4 primary partitions limit. So, how can I get rid of the MBR tables on the hybrid scheme in a manner that still leaves Mac OS and Windows 8 in working conditions? Details: Hardware is the MacbookPro Retina. Primary MBR partitions are consumed as follows: EFI partition HFS+ partition (=encrypted, therefore ="Apple_CoreStorage") HFS+ partition (Recovery partition, contains unencrypted Mac bootloader) NTFS partition (Windows8 all-in-one partition) diskutil list output sid-mbpr:~ sid$ diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *251.0 GB disk0 1: EFI 209.7 MB disk0s1 2: Apple_CoreStorage 160.0 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 4: Microsoft Basic Data Win8 90.1 GB disk0s4 GPT vs MBR addresses sid-mbpr:~ sid$ sudo gptsync /dev/rdisk0 Password: Current GPT partition table: # Start LBA End LBA Type 1 40 409639 EFI System (FAT) 2 409640 312909639 Unknown 3 312909640 314179175 Mac OS X Boot 4 314179584 490233855 Basic Data Current MBR partition table: # A Start LBA End LBA Type 1 1 409639 ee EFI Protective 2 409640 312909639 ac Apple RAID 3 312909640 314179175 ab Mac OS X Boot 4 * 314179584 490233855 07 NTFS/HPFS Status: GPT partition of type 'Unknown' found, will not touch this disk.** **: Ignore this message, the gptsync tool is old and doesn't understand the UUID for "Apple_CoreStorage" / FileVault2 partitions. Since LBA addresses are alright, safe to ignore this message.

  Read the article

• SSH from mac to linux -> start gnome-session -> X11 keyboard mapping all messed up.

  - by Justin

  I have 2 computers: echo.local is running Ubuntu 9.04. justin.local is running Mac OS 10.6.1. X11 version on the mac is 2.3.4. I open X11 on the mac, and open a new xterm window (Applications Menu - Terminal), everything is fine. Keyboard works as expected. I do ssh -X echo.local from the mac (connecting to the linux box), and from the linux command prompt, start xterm - everything is fine. Keyboard works as expected. I do gnome-session from the linux command prompt (through SSH), gnome launches, but keyboard mapping is ALL types of screwed up. If I kill gnome-session and open an xterm via ssh, keyboard mapping is still screwed up. If I then kill the SSH session entirely, and do X11 - Applications Menu - Terminal, opening a brand new xterm window on the mac with no SSH session running at all ... keyboard mapping is still screwed up. Only after I quit X11 and relaunch, is the keyboard mapping back to normal. Keyboard layout under GNOME is Apple-MacBook/MacBook Pro.

  Read the article

• /etc/crontab or any user crontab is not being executed

  - by ian

  My server is CentOS 5. When I edit /etc/crontab or edit any user(including root) crontab via "crontab -e" command, it just adds "(system) RELOAD (/etc/crontab)" or "(admin) RELOAD (cron/admin)" in the log. No CMD in the /var/log/cron. Sample entry in /var/log/cron: Aug 10 10:21:33 localhost crontab[31688]: (root) BEGIN EDIT (root) Aug 10 10:21:42 localhost crontab[31688]: (root) REPLACE (root) Aug 10 10:21:42 localhost crontab[31688]: (root) END EDIT (root) Aug 10 10:22:01 localhost crond[2688]: (root) RELOAD (cron/root) Result of "service crond status": crond (pid 1345) is running... The command "cat /var/log/messages | grep cron" does not give anything. Contents of /etc/cron.allow: admin root Contents of /etc/crontab: SHELL=/bin/bash PATH=/sbin:/bin:/usr/sbin:/usr/bin MAILTO=root HOME=/ # run-parts 01 * * * * root run-parts /etc/cron.hourly 02 4 * * * root run-parts /etc/cron.daily 22 4 * * 0 root run-parts /etc/cron.weekly 42 4 1 * * root run-parts /etc/cron.monthly * * * * * root run-parts /bin/date >> /data/date.txt Result of ps aux |grep cron: root 1345 0.0 0.1 5268 1204 ? Ss 11:43 0:00 crond Contents of admin's crontab: * * * * * /bin/date >> /data/date.txt Note that it's not only admin's crontab that's not running. All cron jobs are not running. Any ideas why they aren't running?

  Read the article

• TeamCity sends inadequate responses after Selenium tests

  - by Dmitriy Sukharev

  I have a TeamCity 7.0.2 at CentOS 6.2 server without X Server. I've installed x11-fonts*, xvfb, firefox, xauth, extracted env. variable DISPLAY=localhost:1, and started xvfb. After that I could start Selenium tests using maven. Tests are executed, but there's an issue with TeamCity. Usually TeamCity starts hehaves absolutely inadequate (it confuses images at the page, sends xml or strange text ampersants and numbers in responses and is a bit slower), also tests are executed 4 times slower (1h 15m) at server than at tester Windows 7-based machine (25m). It worth to notice that tests launch two Jetty servers for tested application (one for REST-services application and another for client). In TeamCity I set JVM command line parameters: -Xms256m -Xmx1224m -XX:MaxPermSize=320m, and Additional Maven command line parameters ends with "-DMAVEN_OPTS=-Xmx1024m" (without quotes). Also both web-services and TeamCity uses the same Oracle server (but different Oracle users). Finally TeamCity and its build agent is at the same server. Server has only 4GB of RAM, but during testing there're 400MB of RAM and 1.2GB of swap. TeamCity and Firefox uses about 65% of CPU during testing. There's no firefox process after end of testing. My knowledge about Selenium is weak. I only know that we use 2.20.0 version of selenium-java maven dependency. Please help me to determine why TeamCity sends wrong responces after Selenium tests. I've tried to give you all information I have, but feel free to ask me for more information.

  Read the article

• Moving automatically spam messages to a folder in Postfix

  - by cad

  Hi My problem is that I want to automatically to move spam messages to a folder and not sure how. I have a linux box giving email access. MTA is Postfix, IMAP is Courier. As webmail client I use Squirrelmail. To filter SPAM I use Spamassassin and is working ok. Spamassasin is overwriting subjects with [--- SPAM 14.3 ---] Viagra... Also is adding headers: X-Spam-Flag: YES X-Spam-Checker-Version: SpamAssassin 3.2.5 (2008-06-10) on xxxx X-Spam-Level: ************** X-Spam-Status: Yes, score=14.3 required=2.0 tests=BAYES_99, DATE_IN_FUTURE_24_48,HTML_MESSAGE,MIME_HTML_ONLY,RCVD_IN_PBL, RCVD_IN_SORBS_WEB,RCVD_IN_XBL,RDNS_NONE,URIBL_RED,URIBL_SBL autolearn=no version=3.2.5 X-Spam-Report: * 0.0 URIBL_RED Contains an URL listed in the URIBL redlist * [URIs: myimg.de] * 3.5 BAYES_99 BODY: Bayesian spam probability is 99 to 100% * [score: 1.0000] * 0.9 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL * [113.170.131.234 listed in zen.spamhaus.org] * 3.0 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL * 0.6 RCVD_IN_SORBS_WEB RBL: SORBS: sender is a abuseable web server * [113.170.131.234 listed in dnsbl.sorbs.net] * 3.2 DATE_IN_FUTURE_24_48 Date: is 24 to 48 hours after Received: date * 0.0 HTML_MESSAGE BODY: HTML included in message * 1.5 MIME_HTML_ONLY BODY: Message only has text/html MIME parts * 1.5 URIBL_SBL Contains an URL listed in the SBL blocklist * [URIs: myimg.de] * 0.1 RDNS_NONE Delivered to trusted network by a host with no rDNS I want to automatically to move spam messages to a folder. Ideally (not sure if possible) only to move messages with puntuation 5.0 or more to folder.. spam between 2.0 and 5.0 I want to be stored in Inbox. (I plan later to switch autolearn on) After reading a lot in procmail, postfix and spamassasin sites and googling a lot (lot of outdated howtos) I found two solutions but not sure which is the best or if there is another one: Put a rule in squirrelmail (dirty solution?) Use Procmail Which is the best option? Do you have any updated howto about it? Thanks

  Read the article

• cisco 2900xl - SNMP - Get mac address of device connected to an interface

  - by ankit

  Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• How to enable synergy 24800 (or some other port) through firewalld

  - by ndasusers

  After upgrading to Fedora 18, Synergy, the keyboard sharing system was blocked by default. The culprit was firewalld, which happily ignored my previous settings made in the Fedora GUI, backed by iptables. ~]$ ps aux | grep firewall root 3222 0.0 1.2 22364 12336 ? Ss 18:17 0:00 /usr/bin/python /usr/sbin/firewalld --nofork david 3783 0.0 0.0 4788 808 pts/0 S+ 20:08 0:00 grep --color=auto firewall ~]$ Ok, so how to get around this? I did sudo killall firealld for several weeks, but that got annoying every time I rebooted. It was time to look for some clues. There were several one liners, but they did not work for me. They kept spitting out the help text. For example: ~]$ sudo firewall-cmd --zone=internal --add --port=24800/tcp [sudo] password for auser: option --add not a unique prefix Also, posts that clamied this command worked also stated it was temporary, unable to survive a reboot. I ended up adding a file to the config directory to be loaded in on boot. Would anyone be able to have a look at that and see if I missed something? Though synergy works, when I run the list command, I get no result: ~]$ sudo firewall-cmd --zone=internal --list-services ipp-client mdns dhcpv6-client ssh samba-client ~]$ sudo firewall-cmd --zone=internal --list-ports ~]$

  Read the article

• How this could happen to my ftp server?

  - by srisar

  hi, again me, i just dont get why i m getting this message, when i try to connect my ftp server thorugh my wan address (112.135.26.115) its saying me, 530 user access denied but when i give the same data to http://ftptest.net the result is as follows... Status: Resolving address of 112.135.26.115 Status: Connecting to 112.135.26.115 Status: Connected, waiting for welcome message Reply: 220-FileZilla Server version 0.9.34 beta Reply: 220-written by Tim Kosse ([email protected]) Reply: 220 Please visit http://sourceforge.net/projects/filezilla/ Status: CLNT http://ftptest.net on behalf of 112.135.26.115 Reply: 200 Don't care Status: USER saravana Reply: 331 Password required for saravana Status: PASS ********* Reply: 230 Logged on Status: SYST Reply: 215 UNIX emulated by FileZilla Status: FEAT Reply: 211-Features: Reply: MDTM Reply: REST STREAM Reply: SIZE Reply: MLST type*;size*;modify*; Reply: MLSD Reply: AUTH SSL Reply: AUTH TLS Reply: UTF8 Reply: CLNT Reply: MFMT Reply: 211 End Status: PWD Reply: 257 "/" is current directory. Status: Current path is / Status: TYPE I Reply: 200 Type set to I Status: PASV Reply: 227 Entering Passive Mode (112,135,26,115,43,9) Status: MLSD Reply: 150 Connection accepted Listing: type=dir;modify=20100322113235; it_is_working!_Andrejs_Cainikovs_from_serverfault.com Listing: type=file;modify=20100322110559;size=5; New Text Document.txt Reply: 226 Transfer OK Status: Success can anyone say why this happens to me? please im trying the whole day!!

  Read the article

• Yum installing wrong MySQL version on CentOS 5 (Amazon)

  - by Marius Stuparu

  I'm having trouble with a CentOS server running on AWS. This is CentOS 5.6 i386 from RightImage, but the problem was the same on all RightScale AMIs. When issuing the following command: yum install mysql mysql-server mysql-devel the only packages proposed by yum are MySQL-devel-community and MySQL-server-community. Which would't be a problem, except this package is old/incomplete, because it does not create a "mysqld" service, only a /etc/init.d/mysql (notice the missing d). That would't be a problem, I can start the service by doing ./etc/init.d/mysql start, and it starts OK, but there is no "mysql" (or other mysql*) command available. If I try to force a different version (yum install mysql50-server...) I get this yum error: mysql-5.0.77-4.el5_6.6.i386 from updates has depsolving problems --> mysql conflicts with MySQL-server-community (even when I don't have MySQL-server-community installed). I have tried this before and after yum update, in a fresh image. How can I install a working version of MySQL? I'm stuck on CentOS 5 because I want to install Kloxo (which does not yet support CentOS 6). I'm not interested in Webmin, and I can't afford cPanel. Thanks!

  Read the article

• Windows 7 Not Starting and System Repair Not Loading

  - by Mark

  I have a Dell Inspiron 1545 running Windows 7 When turning on my PC I keep receiving a black screen with the option to use System Repair or Start Normally. Both options lead me to the System Repair background except no matter how long I wait the system restore options never show up. Choosing F8 and running all of the options including safe mode encounters the same result above. I tried to to use 2 system recovery disks 32x and 64x I downloaded and both lead to similiar results. When I choose System Repair running from the disk the System Repair Question asking to select a language pops ups but after this no matter how long I wait no other options appear. Next after restarting and selecting F8 (after hitting f12 and running from CD) I choose 'Run From Safe Mode with Command Prompt' I am able to run all of the options from System Restore with differing results: Startup Repair: Choosing this ends up in system repair indefinitely (left running 12 hrs) System Restore: Does Nothing. PC thinks for a second and then stops. When selecting ShutDown I see an error message stating there are no restore points. System Image Recovery: Service Cannot be started in Safe Mode Windows Memory Diagnostic: Runs test but then leads to system repair background which never loads system repair Command Prompt: chkdsk /r -Cannot Lock Current Drive...write protected. chkdsk /f -Cannot Lock Current Drive...write protected. bootcfg - Cannot open Boot.Ini file bootcfg - Ran all 3 (rebuildBcd, FixMbr and Fixboot) but PC still goes to System Repair background with no repair options popping up upon restart (without recovery CD). I'm on the verge of purchasing a boot utility disk for $50 unless there is anything else short of "take it to a computer shop" that somebody can suggest I try.

  Read the article

• Windows 7 - How to access my documents from Windows 8 (dual boot)

  - by msbg

  I am dual booting Windows 7 and Windows 8 on two different partitions of the same drive: Win7: (C:) Win8: (D:) I am trying to get access to my Win7 user folder (C:\Users\Mason) in order to access my Win7 documents folder (C:\Users\Mason\Documents) from Windows 8. When I try to on Windows 8, I get an error message saying "You don't have permission to access this folder. Click here to permanently get access to this folder". When I click, the progress bar in Windows Explorer slowly moves to the maximum and disappears. When I try opening the folder, I get the same error message. When editing security permissions for the folder in Windows 8, Explorer freezes. I do not know how to remove the restrictions from Windows 7. I checked the Windows 8 user folder (D:\Users\Mason) and it had the group or user name: "S-1-5-21-936898901-3363470404-1273668825-1001". I tried copying and pasting it into the Win7 User Folder Permissions, but got the error "An object with the following name cannot be found". How would I access my folders?

  Read the article

• USB Mouse and Keyboard not working in Linux 4 Tegra

  - by Sijo

  I am a new person in Tegra Linux development. I have Tamontem NG Evaluation board with Tegra 3 Chip. I installed L4T sample file system from NVIDIA tegra Resources (https://developer.nvidia.com/linux-tegra) and installed the file system as described in the documentation provided in NVIDIA site. Already these was an SD card with L4T running. i dont want to change the boot loader. So I copied the boot.scr.uimg to root (/) folder and uImage to boot(/boot/) and it starts booting from the existing SD card. After that while booting, some errors occurred in some Bluetooth devices (there is no bluetooth device in the board). So I disabled Bluetooth by giving the following command sudo mv /etc/init/bluetooth.conf /etc/init/bluetooth.conf.noexec Now the problem is that mouse and keyboard are not working. So i cannot login. Even though i installed desktop, the mouse and keyboard are not working. But mouse and keyboard are enumerating. lsusb command is showing the USB mouse and keyboard. The installed file system is Ubuntu 13.04. Linux Kernel version is 3.1 What to do. Please help.Thanks in Advance.

  Read the article

• Server Bash Line Wrapping Over Text & In Wrong Place

  - by Pez Cuckow

  This is quite a hard problem to explain, when connecting to one of my servers using the bash shell, under any user the line wrapping is broken and has all sorts of problems. Once of which I detail in screenshots below: Other problems I experience include nano getting very confused about which line and or letter I am on, as shown by typing the same message into nano: These problems only occur when connecting as I previously mentioned to one of my servers which runs CentOs. Do you know why this is occurring and what I can do to fix it? On other servers the message works fine! Thanks for your time, Output of requested commands: Server that doesn't work properly: Working server: Could it perhaps be the custom prompt on the non working server? In .bashrc PS1='\e[1;32m\u@\h\e[m:\e[1;34m\w\e[m$ ' Commenting this out appeared to resolve the problem. Google says line wrapping errors can occur if you don't conform to these rules use the \[ escape to begin a sequence of non-printing characters, and the \] escape to signal the end of such a sequence I am not sure where this would fit in on my prompt?

  Read the article

• Installation Error on Windows Vista: "Side-by-Side configuration is incorrect"

  - by Maxim Z.

  NOTE: This is not a dupe of this other question. That question refers to a similar problem with 2 programs, while I'm only having it with 1, so the solution there doesn't apply to my situation. My relative asked me to install H&R Block 2009 on his Windows Vista 32-bit computer. I ran the installation program, which succeeded, but when I try to open the application itself, it gives me the following error: The application failed to start because its side-by-side configuration is incorrect. Please see the application event log for more detail. Here are the steps I've done so far to try and remedy this problem: In elevated command prompt, run the command: sfc /scannow Uninstall H&R Block 2009 Uninstall Microsoft Visual C++ 2005 Redistributable Reinstall Microsoft Visual C++ 2005 Redistributable by downloading from MSFT website Reinstall H&R Block 2009 This didn't fix it. I've searched for a long time and haven't found anything that works. The H&R Block site itself states that the way to fix this problem is to uninstall and reinstall H&R Block 2009. Has anyone run into this issue before? If so, how can I fix it? Thanks in advance.

  Read the article

• Importing csv list of contacts into Exchange 2007 GAL and create Distribution Group

  - by Ken Ray

  Here's the situation: We have a list of about 1,000 contacts (Lawyers in the area our court serves) with name and email address. I've been asked to create an email distribution list that can be used to sent emails to all of the external users on that list. I've seen various articles using the Exchange Management Shell and the Import-csv command piped through a ForEach-Object to a New-MailContact to set up the contacts. However, Exchange Management Shell is rather unhelpful, and it isn't working. What I believe I need to do is: 1) Set up a new distribution group using the Exchange Management Console. Let's say this new distribution group (which appears in the list of Distribution Groups under Recipient Configuration) is called "FloridaBar". 2) Make sure I have a csv file of the information I want to import. 3) Open Exchange Management Shell, and enter the following command: Import-csv C:\filename.csv | ForEach-Object { New-MailContact -Name $."NameColumnName" -ExternalEmailAddress $."EmailAddressColumn" -org FloridaBar Now, creating 1,000+ contacts in active directory - I assume that shouldn't be an issue. Do I have the "-org" parm wrong? Do I need to spell out the complete organization unit name (my.domain.name/Users/FloridaBar)? Is there a better way of doing this? Thanks in advance Ken

  Read the article

• Re-configure Office 2007 installation unattended: Advertised components --> Local

  - by abstrask

  On our Citrix farm, I just found out that some sub-components are "Installed on 1st Use" (Advertised), which does play well on terminal servers. Not only that, but you also get a rather non-descriptive error message, when a document tried to use a component, which is "Installed on 1st Use" (described on Plan to deploy Office 2010 in a Remote Desktop Services environment): Microsoft Office cannot run this add-in. An error occurred and this feature is no longer functioning correctly. Please contact your system administrator. I have ~50 Citrix servers where I need to change the installation state of all Advertised components to Local, so I created an XML file like this: <?xml version="1.0" encoding="utf-8"?> <Configuration Product="ProPlus"> <Display Level="none" CompletionNotice="no" SuppressModal="yes" AcceptEula="yes" /> <Logging Type="standard" Path="C:\InstallLogs" Template="MS Office 2007 Install on 1st Use(*).log" /> <Option Id="AccessWizards" State="Local" /> <Option Id="DeveloperWizards" State="Local" /> <Setting Id="Reboot" Value="NEVER" /> </Configuration> I run it with a command like this (using the appropriate paths): "[..]\setup.exe" /config ProPlus /config "[..]\Install1stUse-to-Forced.xml" According to the log file, the syntax appears to be accepted and the config file parsed: Parsing command line. Config XML file specified: [..]\Install1stUse-to-Forced.xml Modify requested for product: PROPLUS Parsing config.xml at: [..]\Install1stUse-to-Forced.xml Preferred product specified in config.xml to be: PROPLUS But the "Final Option Tree" still reads: Final Option Tree: AlwaysInstalled:local Gimme_OnDemandData:local ProductFiles:local VSCommonPIAHidden:local dummy_MSCOMCTL_PIA:local dummy_Office_PIA:local ACCESSFiles:local ... AccessWizards:advertised DeveloperWizards:advertised ... And the components remain "Advertised". Just to see if the installation state is overridden in another XML file, I ran: findstr /l /s /i "AccessWizards" *.xml Against both my installation source and "%ProgramFiles%\Common Files\Microsoft Shared\OFFICE12\Office Setup Controller", but just found DefaultState to be "Local". What am I doing wrong? Thanks!

  Read the article

< Previous Page | 565 566 567 568 569 570 571 572 573 574 575 576  | Next Page >