Search Results

Search found 17683 results on 708 pages for 'side loading'.

Page 576/708 | < Previous Page | 572 573 574 575 576 577 578 579 580 581 582 583  | Next Page >

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

• How to remove Media Center from Windows 8

  - by Arabella

  I bought 2 Windows 8 upgrades, 1 for my PC and 1 for my notebook. I added Windows Media Center to my notebook using the free offer in November (side note: the key was emailed to me within 5 minutes, I see many people have been complaining that it takes a few days). Today I decided to add WMC to my PC as well, so I went onto the Microsoft website, same like last time, and I received the email within a few minutes. Once I added WMC, entered the key and the computer rebooted, my activation is now broken: This product key is already being used on another PC. Try a different key or buy a new one. After rereading the product key email, I realised that the WMC key was exactly the same as the one I had received in November for my notebook (I used the same email, i.e. my Microsoft account Outlook email, for both). I didn't think this would be a problem, as on Microsoft's feature pack page it states: ...is limited to five licenses per customer per promotion. So then I decided, I'll just remove WMC from my PC and go back to Windows 8 Pro. So I turned off the WMC feature, PC restarted, activation still broken because my key has been replaced. I then tried to activate it with my original Pro key. The error it gave was that this key cannot be used with this version of Windows, as it is now Windows 8 Pro with Media Center and not Windows 8 Pro anymore. I've searched a bit and it seems the only way to remove it is do a clean install. I tried the Windows 8 Downgrade Helper, which told me I was already running Win 8 Pro when I tried to downgrade, and that I was running Win 8 Pro with Media center when I tried the other option. To sum up: How do I remove Windows Media Center from Windows 8 Pro without having to do a clean install?

  Read the article

• Pushing Windows Store apps silently

  - by seagull

  As part of a requirement I have been issued, I seek the ability to push apps from the Windows Store (.appx) to remote users. The framework surrounding the data transmission is sorted; What I need to know is if there is a script that can be sent out along with a URI or the package proper to facilitate installation on the user-side of the Windows Store app. I am well aware that numerous guides exist from Microsoft on pushing out Line-of-Business (LOB) (AKA Enterprise) applications -- that is, apps that have been developed in-house and are not for the consumption of the Windows store. This is inappropriate for my requirement, however; the customer wants their clients to receive apps that appear currently on the Windows Store, and for them to be installed in a silent manner. I've seen this guide; http://blogs.technet.com/b/keithmayer/archive/2013/02/25/step-by-step-deploying-windows-8-apps-with-system-center-2012-service-pack-1.aspx, which details doing exactly this, but it is only applicable to machines that are administered by a system running Windows Server 2012 R2 with the 'System Center 2012' bundle installed. The systems I target are considerably more decentralised than this, making this guide inappropriate. I have a hunch that Microsoft have deliberately designed the Windows Store to be this way, but I figured I ought to ask around before I resign myself to the requirement. Much obliged

  Read the article

• Ubuntu network card problem.

  - by Steve Greene

  Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

  Read the article

• VMware Workstation Bridged Network Host UnReachable

  - by user2097818

  VMware Workstation 7 on Win7-64 (Home Premium). I have confirmed this on any guest running on this machine (from winxp to debian). I am using a bridged network connection for my guests (Automatic on VMnet0). All of the network configuration is done with DHCP (including on the host). Problem What I can not do: Ping my host machine from inside any VM. (either shows me "Destination Host Unreachable" or will just timeout) What I CAN do right after power up, with no problems at all. I can connect to the internet from inside the VM I can ping my router from inside the VM I can ping other machines on my network from inside the VM Other machines can ping the VM Other machines can ping the host My host machine can ping the VM (this one is important. read further) Details So I have my router assigned as 192.168.2.1/255.255.255.0, and the router provides the DHCP service (and it seems to be doing so successfully). There are no IP conflicts on the network that I am aware of. All Gateways and Subnet masks are appropriate and matching. My entire workshop is on one single subnet, with one single DHCP server and gateway. There is one method in which I can ping successfully, but it requires an active connection initiated from the host (I start pinging from host to VM). During the period of the active connection, I can successfully ping from VM to host, using explicit IP address. As soon as the host connection is closed, the VM ping starts hanging with the same old messages. My Thoughts This really feels like a firewall problem, but I have turned off all firewalls on host and VM, powered down the network, powered back up, and the problem still persists. And if it was firewall, why would only the IP address associated with bridged VM networks be blocked. I feel as though my host operating system (Win7) is somehow configured incorrectly, or, VMware Workstation is configured incorrectly from the host side. Although I have done my best to put everything in default, I feel like I am missing something silly.

  Read the article

• GPO startup script not copying files

  - by marcwenger

  I created a GPO startup script to execute for computers in a specific AD container. The script takes a file from the AD netlogon share and places it on a directory on the computer. Given the right permissions (ie: myself) can execute the script just fine and the file copies. But it doesn't work on startup - the file does not copy over from the AD server. The startup script should run as localsystem (am I right?). So the question is why do the files not copy on startup? Could it be because of: Is it permissions of the local system user? Reading the registry is problematic on startup? Obtaining files from the AD netlogon folder is problematic on startup? Am I missing it completely? My test machine does have the registry key and local directories as described in the script. I myself have standard user permissions on the test machine. AD server is Windows 2008, test client is Windows XP SP3 (and soon to be Windows 7, which I assume permissions issues will be inevitable) Dim wShell, fso, oraHome, tnsHome, key, srcDir Set wShell = WScript.CreateObject("WScript.Shell") Set fso = CreateObject("Scripting.FileSystemObject") key = "HKLM\Software\Oracle\Oracle_Home" On Error Resume Next orahome = wShell.RegRead(key) If err.Number = 0 Then tnsHome = oraHome + "\" + "network\admin\" srcDir = wShell.ExpandEnvironmentStrings("%logonserver%") + "\netlogon\UpdatedFiles\" fso.CopyFile srcDir + "file1.ext", tnsHome, true End If Side note: To ensure that the script is properly deployed, I purposely put some errors in the script, and on the next startup the error message appeared. So I know the GPO is deployed properly.

  Read the article

• Httpd and LDAP Authentication not working for sub-pages

  - by DavisTasar

  I just recently installed a Nagios implementation, and I'm trying to get LDAP authentication working for httpd on Red Hat. (nagios.conf for Apache config below, sanitized of course) ScriptAlias /nagios/cgi-bin "/usr/local/nagios/sbin" <Directory "/usr/local/nagios/sbin"> #SSLRequireSSL Options ExecCGI AllowOverride none AuthType Basic AuthName "LDAP Authentication" AuthLDAPURL "ldap://my.domain.controller:389/OU=Users,DC=my,DC=domain,DC=controller?sAMAccountName?sub?(objectClass=user)" NONE AuthzLDAPAuthoritative off AuthLDAPBindDN "CN=NagiosAdmin,DC=my,DC=domain,DC=controller" AuthLDAPBindPassword "myPassword" require valid-user </Directory> Alias /nagios "/usr/local/nagios/share" <Directory /usr/local/nagios/share> #SSLRequireSSL Options None AllowOverride none AuthBasicProvider ldap AuthType Basic AuthName "LDAP Authentication" AuthzLDAPAuthoritative off AuthLDAPURL "ldap://my.domain.controller:389/OU=Users,DC=my,DC=domain,DC=controller?sAMAccountName?sub?(objectClass=user)" NONE AuthLDAPBindDN "CN=NagiosAdmin,DC=my,DC=domain,DC=controller" AuthLDAPBindPassword "myPassword" require valid-user </Directory> Now, the initial authentication works, so when you first hit the page you can log in just fine. However, when you go anywhere else, it prompts you for authentication, fails (asking for a re-prompt), and gives this error message: [Mon Oct 21 14:46:23 2013] [error] [client 172.28.9.30] access to /nagios/cgi-bin/statusmap.cgi failed, reason: verification of user id '<myuseraccount>' not configured, referer: http://<nagiosserver>/nagios/side.php I'm almost certain its a simple flag or option, but I just can't find it, and I don't have a lot of experience working with Apache. Any assistance or help would be greatly appreciated.

  Read the article

• Exceptional slowdown of robocopy copying from VM to DFS array

  - by user1588867

  I've got an old win 2003 VM (VMware) on a blade cluster of VMs that I'm moving a considerable amount of files to our new DFS array. There are two main folders with about 1.7 million and half a million smaller files (letters, memos, and other smaller files) respectively. Total size is ~420 GB and ~100 GB. We're using the gui version of robocopy on the server to copy the files. We had initiated a file copy about a month ago to test the process and found that it was taking around 4 hours for the large file. Now that I'm in the process of actually switching the files over it has been taking 18-20 hours. Nothing has changed on the server side and nothing has changed on the settings of the copy (no logs, 1 retry with a wait of 1 second). Our intent is to shut off the share and force the copy over again to get all the files that have been left out of the copy due to being locked by users. I can't take a 20 hour outage to do that though. Does anyone have any theories about what could be causing such a delay for robocopy compared to previously shorter runs?

  Read the article

• Parallels 6 - Is It Just Me or Does It Run Really Slowly?

  - by 5arx

  I've been running Parallels since version 2 with great success. I use it as my .Net development environment and over the last few years have converted so many others to the Parallels/Mac way of doing Windows/.Net development that I feel I should be getting perks/gifts and/or freebies from Parallels Corporation ;-) A month or so ago I upgraded to version 6 and ... immediately wished I hadn't. I'm currently running it on a laptop - a 2009 MacBook Pro (13"/2.53Ghz/4GB) while my MacPros at work and home are still running v5. I have seen nothing in v6 that makes me want to upgrade the install on those. The general problem is performance - upon starting or suspending a vm (always Windows 7 Ultimate), OS X slows down, quite often freezing for a minute or two at a time. The performance of the vms themselves are fine, but for me the point of this set-up is to be able to do web-browsing, email checking etc. on the OS X side of things while doing the stuff that can only be done on Windows (Visual Studio, SQL Server tools) on Windows. I have been using Parallels for a while so at least feel like I know what I'm doing so at the moment I am heading towards forming an opinion that its Parallels thats to blame. I've tweaked and tweaked all the vm configuration properties but to no avail. Support emails to the company have all received replies - there are no documented case of the issue you mention. Has anyone else seen this problem and if so, have you found a fix?

  Read the article

• How can laptop keyboard keys be removed and replaced?

  - by Lord Torgamus

  I'm trying to fix a laptop keyboard that has issues with keys on its left side. Just by feel, it's clear that something sticky got under there. There could be something crunchy too, but that might just be the sound of the key's spring releasing itself from the sticky. I don't know the cause because it's not my computer and the owner isn't sure, but I'm guessing soda spill for now. The computer is an HP dv2500. I've removed the keyboard and blown under it but that hasn't helped. I didn't use compressed air because I just don't have any available, but I suspect it wouldn't help with sticky. So, I'd like to pop they keys off and clean with damp cotton swabs or similar. Is there a proper way to remove the keys? I've found some instructions via Google for non-laptop keyboards, but they don't seem like they'd work for me. Alternate solutions to the problem also welcome, but I've been curious about how to remove the keys for some time for other reasons.

  Read the article

• Cache Control Headers with IIS 7.5

  - by Brad

  I'm trying to wrap my head around client side (web browser) caching and how it works in relation to IIS 7.5 cache control headers. In particular: If we want to force clients to reload cached resources, how must IIS be configured? Do we need to set expire web content immediately if the resources on the server have a more recent Modified Date (or ETag value)? Right now we're not setting any cache headers. So if I set a cache header of no-cache (which I think is the equivalent of expire web content immediately) will that force the web browser to obtain a new version of a particular file. Or will the browser only request a new version after it deems its current copy to be stale and then from that point forward not cache it? Would a best practice be to set a cache control flag of 1 week, then 8 days before I know I am going to make a change set the cache control down to for instance 30 minutes? But if I do that and then need to immediately expire an item from users caches because there was an issue with it how do I do that?

  Read the article

• Which CPU for XEN - LAMP testbed - Budget

  - by deploymonkey

  Dear serverfault knowledgeables, im in a decision dilemma right now, which I can't resolve due to lack of hands on experience. I need to build a testbed for basically virtualizing a LAMP application (os'ses not yet decided) including server side calculations. I'll opt for XEN since it seems better supported by cloud hosters at the moment. The hardware is for a proof of concept for a startup doing saas and might be used for closed live alpha/beta later on. After testing, the testbed might be a) deployed as a colocated white box server b) used as workstation Single socket is enough. We want to have ECC memory for reliability, this excludes most of the consumer line at intel. If intel CPU, then threaded cpu (HT) is preferred have at least 16 gig ram If justified by price and reliability is not too bad, a high quality desktop MB instead of a server MB would be worth a try It came down to the opteron 6128 vs. the xeon 5620 for me after a lot of research, but I don't necessarily have to be right. Which CPU is preferrable, concerning TCO (MB price, power requirements 24/7...) , Opteron 6128 or Xeon 5620? Which one offers better performance in real world applications? (Do You have any other suggestions I probably overlooked?) Thank You for Your consideration

  Read the article

• Vim clobbering scrollback buffer outside of screen

  - by dotancohen

  If I'm not in a screen session, then when exiting Vim I get a bash prompt below the remnants of the VIM window. A side effect of this is that my scrollback buffer is clobbered, especially if I have paged through a long file in VIM. The problem only occurs if I'm not in screen, inside a screen window VIM exits to show the bash prompt and the previous lines just as before. I tried adding sett_ti=t_te= to my .vimrc to fix the problem, but the only effect that it has was to break VIM such that the problem occurs inside screen as well as outside. Thus, I removed the line. For good measure I do have altscreen on in .screenrc. This is on Ubuntu Server 12.04.1 LTS, with Bash 4.2.24, Screen 4.00, and VIM 7.3 (not vim-tiny), accessed over SSH in Cygwin version NT-6.1-WOW64 on a Windows 7 laptop. Thanks. EDIT: Note that in the same Cygwin install I can SSH into a different server (CentOS) and there VIM does not clobber the scrollback buffer. Therefore, I do not suspect a Cygwin issue. The CentOS machine does not have screen installed, and I did not have to add set t_ti= t_te= to .vimrc.

  Read the article

• Ping with explicit next-hop selection (aka Monitoring multiple default gateways)

  - by Michuelnik

  I have a linux (debian) router with two internet connections (A) and (B). (A) is preferred, (B) is fallback. I want to monitor the internet connection (and not only the availability of the gateways!) and change the default route appropriately. If (A) is not providing internet, switch to (B) If (A) is providing internet again, switch back to (A). Only problem I have is in case (2). My routing table points towards a working internet so I cannot easily detect whether internet is working over link (A) again. I am search for a ping or traceroute (or other diagnosis-tool) which can select the next-hop explicitly. ping -r looks promising, but can only ping a host on the lan. (It only has to write another destination address in the packet, damnit!) traceroute -g gateway looks even more promising and nearly does what I want - but sets source routing options which my next-hops deny. (Not within my administrative boundary...) I just want a $ping, that can: select a source interface (and address) select a next-hop on that interface ping any arbitrary ip address I could do evil trickery with policy-based routing but that would have production impact for all users. I would like to see a side-effect-free solution....

  Read the article

• Plesk FTP not working but SFTP and Shell is working

  - by shamittomar

  I am facing a strange problem. The FTP on my Plesk VPS is not working. Whenever I try to connect, FileZilla FTP client says: Status: Resolving address of xxxxxxxxxxxxx.com Status: Connecting to xxx.xxx.xxx.xxx:21... Status: Connection established, waiting for welcome message... Error: Could not connect to server So, it's not even going to the step of asking username/password. So, it's something else. The SFTP on port 22 is working fine. Also, I can successfully do shell access and run commands. But, I NEED FTP access too on port 21. I have searched everywhere but can not find any setting to enable it. This is the Plesk version info: Parallels Plesk Panel version 9.5.2 Operating system Linux 2.6.26.8-57.fc8 CPU GenuineIntel, Intel(R) Pentium(R) 4 CPU 3.00GHz Any help is appreciated. [EDIT]: The firewall is not blocking it. I have checked it on server and there are absolutely no blocking rule. Firewall states: All incoming/outgoing connections are accepted on FTP And on client-side (my PC), I can connect to other FTP servers so this is not an issue in my PC's firewall. Moreover, I can not even connect to the FTP from online FTP clients like net2ftp.

  Read the article

• How can I make sound over hdmi in kubuntu work?

  - by user32509

  I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :)

  Read the article

• Why are SIP calls via my server silent?

  - by Archcode

  I have FreeSWITCH SIP server up and running. It has public IP and sits behind 1-to-1 NAT (it's Amazon EC2 instance actually). I can connect to it, make a call to other endpoint (namely, my android device to my pc and vice versa) and signals are send with no problems (call, answer, hangup, etc). Unfortunately, and what drives me crazy, that's all: no audio gets through, no video either. Server does not throw errors, it reports many retransmission though, looks like this: switch_rtp.c:915 [ zrtp engine]: WARNING! HELLO Max retransmissions count reached (20 retries). ID=15 Codecs are set up correctly (same config worked locally on my LAN). NAT/firewall on client side may be a problem, signals do get through (perhaps due to fixed port, data streaming runs on random one, that is currently my best bet). STUN/TURN/ICE setting on client seem to have no effect. Endpoints sit behind symmetric NAT. On server there are no iptables rules, security group is set as suggested there: http://wiki.freeswitch.org/wiki/Firewall Help, please. How to make it work or at least diagnose what's wrong?

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

• CPU not working on a specific motherboard

  - by Shaman

  I'm making a computer for someone and I met a weird problem. The CPU that I have doesn't work on this motherboard. The CPU is an Intel Pentium D 925 and the motherboard is an ECS G41T-M6, which in theory should work together. The only thing reused is the power source(400W). When I start the computer, the fans start, and that's it. The BIOS doesn't boot. I tried my own power source (600W Corsair) and nothing. Removed the RAM, no warning. In desperation I tried the last thing, swaped my own CPU with this one (Core2Duo E7200). Lo and behold, it worked. Both. The Core2Duo worked on the ECS with the old power source and the RAM that I used in the first place, and the Pentium D worked on my Gigabyte G31M-ES2L. What I discovered was that the Pentium D didn't receive power on the ECS, because I tried running it without the cooler and it remained at room temperature. On a side note, I also removed the HDDs just in case. So, in conclusion, any ideas? I can't return it, and I can still use it to upgrade another PC, but I would really prefer not to buy another CPU if possible.

  Read the article

• vSphere Promiscuous mode only receiving packets one way from network switch

  - by steve.lippert

  We have two network switches, a POE switch (SwitchA) to power our phones / users computers and a non-POE switch (SwitchB for the rest network.) Each switch is setup to do port mirroring to support our VoIP recording system. SwitchA does port mirroring on specific ports if we need to record a user. SwitchB mirrors one port to monitor our work at home users (Internet comes in from managed router, to switch, back out to our firewall.) These two port mirroring setups feed into one vmware vSphere 4.1 server, it has four total physical cards. The other two NICs feed into an unmanaged switch for connecting to the rest of the network. Once into the vSphere server all network ports go into a vSwitch, and then one of the servers (Windows 2008 R2) sniffs them out and does its thing. Everything is working fine and dandy from SwitchB. But on SwitchA we only receive one side of the VoIP packets (going out to the phone, nothing coming in from the phone). Troubleshooting steps I have taken so far: I hooked up my laptop to the monitor port on SwitchB and I see both sides of the packets. I swapped which network interface is plugged into the monitor port on SwitchA. Because everything feeds into one vSwitch / vNetwork and both sides of the conversation arrive just fine from SwitchB I believe everything is configured correctly on the vSphere server/guest. What could be causing one way packets to arrive on my guest machine from only one interface, but not the other? Could a bad cable be causing the problems from SwitchB?

  Read the article

• Linux: Can't overwrite files on samba store

  - by jonescb

  I'm using CentOS 5.5 with smbclient 3.0.33-3.28-el5 (latest version in repo), and I can't overwrite files in my Samba store. I am not the admin for the Samba server, so there isn't anything I can do server side. But I do have write permission to the server. I know the server runs Windows XP or Server 2003; I don't know. I can delete the file, and then copy the new version over, but I can't overwrite it. Using the cp command I'll get this error: [jonescb@localhost ~]$ cp foo.txt /mnt/si_storage/foo.txt cp: cannot create regular file `/mnt/si_storage/foo.txt': No such file or directory` And if I edit a file on the server using vim, I can save it once, but if I save it again I get this: "/mnt/si_storage/foo.txt" E212: Can't open file for writing This is my /etc/fstab entry for the samba server: //192.168.1.2/SI_STORAGE /mnt/si_storage cifs username=myuser,password=mypass 0 0 Edit: I can overwrite files just fine on my XP machine. The CentOS box is the only one having problems.

  Read the article

• WAN Optimization for Small Office/Home Office

  - by TiernanO

  I have been reading up on WAN optimization for the last while, mostly out of interest of speeding up my own internet connections, but also to speed up the office internet connection. At home, I have 2 cable modems plugged into a RouterBoard RB750, which load balances the connections. In the office, we have a single connection into a NetGear router. Most of the WAN Optimization products I have seen, seem to be prohibitively expensive, but also seem to be based on the idea of having multiple branches around the world. What I am looking for, ideally, is as follows: software install: I am "guessing" I need to install it in 2 places: one in the office or house, and one in "the cloud". any connections going to, say, The US (we are in Europe, but our backup's live in the US currently, which would be something important to speed up) would be "tunnelled" though the Optimizer. If downloading or uploading large files, open multiple connections between both "the cloud" and the optimizer... This is where a lot of speed could be gained. finally, for items not compressed, they would be compressed on the cloud side of things, also items that are already on the optimizer could be not sent again. kind of like RSync or Proxy servers... So, is there something that can be done? Is it available using off the shelf components (some magic script with SSH, Squid, Linux and duct tape) or is it something that needs to be purchased? or even an Open Source Project that does 90% of what i am asking?

  Read the article

• Can't access random web pages on my MacBook Pro 2012?

  - by Faruk Sahin

  Sometimes I can't access random web pages. The page simply doesn't load. If I wait for around a minute doing nothing, it will load. It happens very random and very intermittent. Sometimes it starts when I try to access youtube.com or cnn.com. When it starts, it happens once in a minute or once in 5 minutes for random web pages. But if I am downloading something, the download continues without any interruption. And also I am able to ping the address I can't browse. Then if I wait for around a minute, everything starts to work fine at the browser side also. I have tried a lot of different browsers. I have tried changing my DNS servers to Google's public DNS servers. Using a cable instead of the wireless connection doesn't work either. No one else in the network has this problem, but me. What can be the problem?

  Read the article

• samba access from win98

  - by SimonSalman

  Hello, the admin installed a new file server in our institute: OpenSuse 11.1 with Samba 3.2.7-11.3.2-2154-SUSE-CODE11. They copied the smb.conf from the old machine (hosting Samba 3.0.0) to the new one. Everything works as before, but one Windows 98 machine can see but not access the file server. It prompts for user authentication, but will not accept any user-password combination. There exists a lot of discussion about the problem on the net, but none provided a clear answer to the problem. EDIT: 1. I changed Win98 registry enable plain-text passwords, and alternatively changed server's smb.conf and /etc/smbpasswd to accept encrypted passwords 2. Further I provide a profile with a user-password combination on Win98 machine similar to one of the samba users-password combinations. 3. I changed smb.conf such that the samba server is the Local Master Browser all these changes are not necessary when using the older samba server. So, I conclude that a configuration problem on the server side is likely. If you need any further information, I will post them here. Best regards, Simon

  Read the article

• Setting up Web server so it is easy to migrate

  - by Nyxynyx

  Hi I am about to move my site from a VPS to another host's dedicated server. One of my concern is about scaling the site in the future that involves a change of server. Now that I am starting the dedicated server from scratch with only the OS, this means that I need to install the web server stack, including Apache and its mods, PHP, MySQL, PostgreSQL, Tomcat, Solr and a few other softwares like ImageMagick and git. Question: Is there a way for me to setup this new dedicated server such that I can easily migrate the entire site, both the technology stack and the code to the a newer server (upgrade from this new dedicated server) easily without reinstalling and reconfiguring everything? The code for the website is being handled by git and github so thats not a problem. I'm more conerned about the rest of the software required. Side question: The current VPS uses CentOs with cpanel and it seems that many packages are outdated on yum and cpanel interfers with the installation of many packages. Which OS should I go with for the new server? Ubuntu?

  Read the article

< Previous Page | 572 573 574 575 576 577 578 579 580 581 582 583  | Next Page >