Search Results

Search found 18728 results on 750 pages for 'setup deployment'.

Page 579/750 | < Previous Page | 575 576 577 578 579 580 581 582 583 584 585 586  | Next Page >

• Routing multiple static IPs from ISP at the cable modem?

  - by Jakobud

  I'm taking over IT responsibilities for a previous IT guy. We have a 50mb cable modem connection from Comcast along with 5 static IP addresses: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 We are in the process of replacing our firewall machine. Currently the firewall box is the only thing connected to the cable modem. However the cable modem has multiple ethernet ports on it, similarly to a router. I have assembled a new firewall machine and its time to start testing and configuring it. So that means that I also need it plugged into the cable modem (remember it has multiple ethernet ports on it). So now with multiple computer plugged into the cable modem, how does the cable modem know where to route the traffic? If some request on the internet is made to XXX.XXX.XXX.181, which goes to our cable modem, how does the cable modem know which connected computer that traffic is supposed to be sent? Looking at the web interface for the cable modem, there doesn't seem to be anything special setup on it with regards to routing or NATing IP addresses. Is that because when there is only one computer connected to the modem, all traffic is sent to it by default? Now that I am going to (temporarily) have multiple computers plugged into the cable modem, do I need to specify routing or NAT rules on the modem itself? I am going to speak to Comcast about this next, but I figured I'd ask here first just so I can get a better grasp on how this type of thing generally plays out.

  Read the article

• Why is my cat5e cable not okay?

  - by torbengb

  My LAN cable seems to work (indicator LED lights up) but the computer can't find a connection. What's wrong? Setup: I had to run a network cable from a router in one room to a computer to another room, through a hole in the wall that was too small to pass the RJ-45 plug through. The plug was cut off and the cable passed through the wall. Then a new plug was crimped on using this detailed explanation. The connection didn't work because the (factory-made!) plug in the other end used a non-standard wire order. I crimped a new plug on again, using the exact same order of the factory-made plug. The LED indicator lights up on both ends, but the computer cannot find a connection. What can be wrong? How can I find out? I don't have a cable tester. By visually inspecting my new plug, I think it's good; the wire order matches the other end, and all wires are all the way inside the plug and reach the connector piece. I've used the cable before (with both factory-made ends) so i don't think that the cable itself has a defect.

  Read the article

• EFI pxe network boot error

  - by Lee

  Asking this on both [serverfault][1] and [superuser][2]. When attempting to network boot RHEL 5.4 on an old ia64 machine I get the following error : ![alt text][3] So I've basically followed the tutorial here : [http://www-uxsup.csx.cam.ac.uk/pub/doc/suse/sles9/adminguide-sles9/ch04s03.html][4] DHCPD,TFTPD etc are already setup and working with standard x86 PXE clients. I've unpacked the boot.img file into /tftpboot/ia64/ and passed the path to the elilo.efi file via DHCP with the filename ""; option. Changing this filename generates a PXE file not found error (see below). So I assume that PXE has found the file... ![alt text][5] The only thing wrong I can find in the logs is : Jan 6 19:49:31 dhcphost in.tftpd[31379]: tftp: client does not accept options Any ideas? I'm sure I hit a problem like this a few years ago but I can't remember the fix :) Thanks in advance! Thanks in advance! [1]: http:// serverfault.com/questions/100188/ efi-pxe-network-boot-error [2]: http:// superuser.com/questions/92295/ efi-pxe-network-boot-error [3]: http:// i.imgur.com/Zx1Jy. png [4]: http:// www-uxsup.csx.cam.ac.uk/pub/doc/suse/sles9/adminguide-sles9/ch04s03.html [5]: http:// i.imgur.com/CEzGf. jpg

  Read the article

• Windows 7 - Wireless Signal Good - Internet Often Says Limited or No Activity

  - by Anthony Trilussa Pizzo

  Hi - I have a New Dell Studio XPS latop that I hooked up in early January of 2010. The Dell Studio XPS laptop is connected to my wireless router (Belkin Wireless N). The router was purchased in Februaru of 2010 because I thought my router was bad (A D-Link router). Comcast is my ISP. Everyday, at random times, the internet will have a good signal (according to the little Win 7 icon on the taskbar) but I will receive a message saying limited or no internet access and I cannot access the internet. I have the internet setup to automatically get an IP and I did the IPCONFIG release / renew but with no success. I even had a WiFi enabled Blackberry right next to my computer and whenever the computer loses an WiFi connection, so does the Blackberry. The router isnt't bad, because the old router did the same thing - giving me limited or no internet access while working sometimes. I also tried using two other laptops in same physical position as my Dell Studio XPS laptop and they have the same problem. I am going crazy trying to figure this out as I have called the Router Company (Belkin), my ISP (Comcast), and my computer maker (Dell). Can anyone offer some suggestions and I can try them as we work through this and maybe one of the suggestion will be right one. Thanks in advance for even reading my problem. I searched for a problem similar to mine on the internet, but I have not been able to keep a steady internet connection. (Side note - I used to have an IBM thinkpad laptop and D - Link router and for years that wireless connection worked FLAWLESSLY, with the same physical set up - the laptop in my bedroom, and the router in the basement.)

  Read the article

• Using Virtualbox Bridge Networking fails connection from Guest OS to Oracle XE running on Host

  - by Licheng

  I am trying to make a JDBC connection from a VirtualBox Ubuntu Guest OS to an Oracle XE database running o Host. However, the connection is refused. Here are the details of my environment: VirtualBox: 4.1.4 Host OS: Windows 7 Guest OS: Ubuntu server 11.4 Networking mode: Bridged network Oracle XE database running on Host Issue: WebLogic server runs on the Ubuntu virtualbox. It attempts to connect to an Oracle XE database running on the Host OS (windows 7) with listening port 1521. On the Guest OS (Ubuntu), I am able to ping the Host computer from the Guest OS. However, when I configured a JDBC data source on the WebLogic server on the Guest OS to connect to the Oracle XE, connection took a long time, and eventually I received an "IO Exception: The Network Adapter could not establish the connection". When I tried "telnet host-ip 1521", no connection was established. With Bridge networking, I can make bi-directional connections between the host and the guest OS (e.g. connection through ssh and ftp). Is there anything I missed in the setup of Bridge networking and the guest/host OS? Note that I was able to make the same connection within a normal networking environment (i.e. not using virtual box). I am not sure whether Bridge networking is a good option for the work described above. Should I use host-only networking mode? If so, any specific configurations I need to perform? I read through the Virtual box document on setting up the host-only network, however, it lacks of details. I followed the procedures described in the manual, and couldn't even connect to the host. Could some experts here enlighten me on this issue? Much appreciated. Licheng

  Read the article

• How to deal with DELL support system?

  - by Nishant Kumar

  We have purchased a Dell Optiplex 9010 SSFV for our organization's work. Since the first installation two of the USB keyboard keys were not working properly. I had to press those keys two times simultaneously, on first time keys did not work and for for second time it printed two characters (as it were buffering first character.) Two keys that were not working properly: Hexangrave (Below the ESC key: `) Double Quotes (Left the enter key ") We registered our complaint with DELL and they suggested (with some hard to understand and weird ENGLISH accent) some test and tricks, such as switching to different ports, checking keyboard on different PC, and it worked well with diff. PC(with Windows 7 Home Premium installed). It was clear that it is an OS fault, hence they suggested to re-install OS. Problem began here, we have a project on the run and currently a video editing project setup on our system, so can't re-install system in hurry and also DELL persons were not providing any other solution such as updating keyboard driver, etc. Arguments I am a Software Engg. and don't think it is a feasible solution to re-install entire system for simple problems. This prob is coming since the fresh system installation, so I don't think it will solve the problem. Finally, I had to find solution myself and got it here, now I want to show my disappointment to dell persons or at least tell them that they should improve there support system to not advice to re-install entire system for that simple problems. Notes We have purchased 5 years NEXT business day support from DELL for around 8000 INR (Not for that kind of solutions from DELL). It is Dell India Support System. So can anyone tell me how to tackle dell support system officially, so that they will pay more attention in near future. Thanks

  Read the article

• Node.js, Nginx and Varnish with WebSockets

  - by Joe S

  I'm in the process of architecting the backend of a new Node.js web app that i'd like to be pretty scalable, but not overkill. In all of my previous Node.js deployments, I have used Nginx to serve static assets such as JS/CSS and reverse proxy to Node (As i've heard Nginx does a much better job of this / express is not really production ready). However, Nginx does not support WebSockets. I am making extensive use of Socket.IO for the first time and discovered many articles detailing this limitation. Most of them suggest using Varnish to direct the WebSockets traffic directly to node, bypassing Nginx. This is my current setup: Varnish : Port 80 - Routing HTTP requests to Nginx and WebSockets directly to node Nginx : Port 8080 - Serving Static Assets like CSS/JS Node.js Express: Port 3000 - Serving the App, over HTTP + WebSockets However, there is now the added complexity that Varnish doesn't support HTTPS, which requires Stunnel or some other solution, it's also not load balanced yet (Perhaps i will use HAProxy or something). The complexity is stacking up! I would like to keep things simpler than this if possible. Is it still necessary to reverse proxy Node.js using Nginx when Varnish is also present? As even if express is slow at serving static files, they should theoretically be cached by Varnish. Or are there better ways to implement this?

  Read the article

• How to kill unkillable Python-processes running as root

  - by Andrei

  I am experiencing an annoying problem with sshuttle running it on 10.7.3, MBA with the latest firmware update -- after I stop it (ctrl+c twice), or loose connection, or close the lid, I cannot restore it until I restart the system. The restarting takes notably more time, than it would normally take. I have tried to flush ipfw rules - not helping. Could you advice me how to restore sshuttle connection (without restarting os)? The following processes remain running as root, which I do not know how to kill (tried sudo kill -9 <pid> with no luck): root 14464 python ./main.py python -v -v --firewall 12296 12296 root 14396 python ./main.py python -v -v --firewall 12297 12297 root 14306 python ./main.py python -v -v --firewall 12298 12298 root 3678 python ./main.py python -v -v --firewall 12299 12299 root 2263 python ./main.py python -v -v --firewall 12300 12300 The command I use to run proxy: ./sshuttle --dns -r [email protected] 10.0.0.0/8 -vv The last message I get trying to restore the connection: ... firewall manager: starting transproxy. s: Ready: 1 r=[4] w=[] x=[] s: < channel=0 cmd=PING len=7 s: > channel=0 cmd=PONG len=7 (fullness=554) s: mux wrote: 15/15 s: Waiting: 1 r=[4] w=[] x=[] (fullness=561/0) >> ipfw -q add 12300 check-state ip from any to any >> ipfw -q add 12300 skipto 12301 tcp from any to 127.0.0.0/8 >> ipfw -q add 12300 fwd 127.0.0.1,12300 tcp from any to 10.0.0.0/8 not ipttl 42 keep-state setup >> ipfw -q add 12300 divert 12300 udp from any to 10.0.1.1/32 53 not ipttl 42 >> ipfw -q add 12300 divert 12300 udp from any 12300 to any not ipttl 42 Update: $ ps -ax|grep python 1611 ?? 0:06.49 python ./main.py python -v -v --firewall 12300 12300 48844 ?? 0:00.05 python ./main.py python -v -v --firewall 12299 12299 49538 ttys000 0:00.00 grep python

  Read the article

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• nginx+mysql5 loadtesting configuration strangeness

  - by genseric

  i am trying to setup a new server running on debian6 and trying to make it work smooth under load. i ve used a wordpress site as a test object, and tried the configurations on http://blitz.io. when i increase the mysql max_connections from 50 to 200 lots of timeouts start to occur. but on 50 , no timeouts and pretty well response times. nginx configuration is fine , i tuned the config so i dont see errors. so i presume it's related to the other configuration options of my.cnf . i read some about options but still cant find what max_connections problem is all about. btw, the server has 16gb of ram and a fine i7 cpu. here is the current my.cnf [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] wait_timeout=60 connect_timeout=10 interactive_timeout=120 user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking bind-address = 127.0.0.1 key_buffer = 384M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 20 myisam-recover = BACKUP max_connections = 50 table_cache = 1024 thread_concurrency = 8 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M thanks in advance. i asked this question on SO but it's closed as off topic so i believe this is a SF question.

  Read the article

• Apache mod_rewrite weird behavior in Internet Explorer

  - by morrty

  I'm attempting to setup redirection for a couple of root domains. Firstly, here is the code in my httpd-vhosts.conf file: <VirtualHost *:80> ServerAdmin ****@example.com ServerName example.com ServerAlias example2.com RewriteEngine On RewriteCond %{HTTP_HOST} !^192\.168\.0\.1$ # This is our WAN IP RewriteCond %{HTTP_HOST} !^www\. [NC] RewriteCond %{HTTP_HOST} !^$ RewriteRule ^/?(.*) http://www.%{HTTP_HOST}/$1 [L,R,NE] </VirtualHost> What this does is redirect the root domain of example.com or example2.com or any host other than www to www.example(2).com The part I'm having a problem with is the RewriteRule itself. the $1 is supposed to match the pattern of the RewriteRule and add it in the substitution. For example: "http://example.com/test.html" should rewrite to "http://www.example.com/test.html" It works in all modern browsers like it's supposed to except for IE8 or IE9 (I didn't test other IE versions). In IE, this works: "http://example.com" to "http://www.example.com" In IE, this does not work: "http://example.com/test.html" to "http://www.example.com/test.html" Does anyone have an explanation for this behavior? I hope I've explained it well enough. Thank you.

  Read the article

• Resolving "JBoss Web Console is Accessible to Unauthenticated Remote Users" vulnerability

  - by IAmJeff

  Our security team has determined there is a vulnerability in one of our systems. We are using version JBoss 5.1.0GA on RHEL 5.10. Vulnerability description: JBoss Web Console is Accessible to Unauthenticated Remote Users Yes, this looks familiar. Refer to Question 501417. I do not find the answer there complete. Can someone (or multiple someones) answer Does a newer version of JBoss fix this vulnerability? Are there links describing, in more detail, manual modification of JBoss configuration files to resolve the issue? Are there others options to remediate this vulnerability? Why don't I find the other answer complete? I'm not at all familiar with JBoss, so this answer seems a bit too simple. The web-console.war contains commented-out templates for basic security in its WEB-INF/web.xml as well as commented-out setup for a security domain in WEB-INF/jboss-web.xml. Just uncomment those basic security blocks and restart? Is there anything else I need to include? This seems generic. Do I need to include anything about my environment, such as absolute paths, etc.? Am I making this too complicated?

  Read the article

• Chroot jail of Nginx and php

  - by sqren

  I'm hosting multiple websites on one VPS, and want to chroot each website, eg. /chroot/website1 /chroot/website2 I'm using makejail, which is a highlevel tool, for creating the jails, and copying the libraries and dependencies. Easy peasy. Each website will need nginx, php and mysql. For php I'm using php5-fpm which actually supports chroot by configuration, however I'm not using this (maybe I should?) My question is which approach of the following three is the better: 1) Every website will have its own seperated instance of nginx, php and mysql. The downside is, that each webserver + php has to listen to a different port. I also need a "master" nginx web server in front of them, reverse proxying to the chrooted servers behind it. Probably most secure, but also most advanced. 2) I don't make any chroot jails manually. I setup one nginx web server, that proxies php requests to php-fpm, on different ports. I can have multiple php-fpm configurations each with is own chroot'ed folder. This is quite managable - however only php will be chrooted. Not the actual webserver. Is this secure enough. Also, I tried this option out, and it seems I will need to use TCP instead of sockets for connecting to MySQL. 3) You tell me ;) I'm quite new to chroot jailing, so please correct me if I'm wrong in my assumptions. I've been reading all the tutorials I could find, however, I find the market for chroot guides very scarce. Any help or inputs much appreciated!

  Read the article

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

• Birt on Tomcat unable to find JARs

  - by LostInTheWoods

  First, my setup: BiRT Runtime: 3.7.2. Ubuntu 10.04 Tomcat 6 Sun Java 1.6.0 I have a jar file I want to deploy onto the Tomcat server so it is usable by the runtime, so I placed the jar file in /var/lib/tomcat6/webapps/birt/WEB-INF/lib. As I understand it this is the default location for JAR files that are going to be used by a BiRT report. But the jar file is not accessible by the report that is trying to call it. In the BiRT logs I see: Error evaluating Javascript expression. Script engine error: ReferenceError: "DynDSinfo" is not defined. (/report/data-sources/oda-data-source[@id="54"]/method[@name="beforeOpen"]#20) Script source: /report/data-sources/oda-data-source[@id="54"]/method[@name="beforeOpen"], line: 0, text: __bm_beforeOpen() org.eclipse.birt.data.engine.core.DataException: Fail to execute script in function __bm_beforeOpen(). Source: "DynDSinfo" is the class I am trying to reference.. and now for the kicker... this works fine on Tomcat6 on Windows 7. The same files in the same places. So is there some additional configuration or some environmental variable that needs to be set, or something different on the Linux (Ubuntu) platform? All help or ideas gratefully received, Stephen

  Read the article

• Tomato OS: "memory exhausted" running vi .... how to solve?

  - by Sam Jones

  I have set up tomato (shibby) on an asus RT-N66U router. It works great. I loaded up a few pieces, like transmission and optware. I can run vi, but when I run vi it fails with a "memory exhausted" error, and the terminal session hangs. For reference: If I simply start "vi" it runs fine. But if I specify vi I get the memory exhausted error, even if the file I am opening is just a couple of hundred bytes in size (like fstab). I discovered that my swap partition was not properly set up, so I did that. The swapon command now indicates I really do have a swap: [root@MyRouter samba]$ swapon -s Filename Type Size Used Priority /dev/sda1 partition 32900860 0 1 How can I get vi to work? Thanks! System setup reference information: asus RT-N66U router 2TB usb hard drive partitions on hard drive: Disk /dev/sda: 2000.4 GB, 2000398839808 bytes 255 heads, 63 sectors/track, 30400 cylinders Units = cylinders of 16065 * 4096 = 65802240 bytes Disk identifier: 0xfacbc8ab Device Boot Start End Blocks Id System /dev/sda1 1 512 32900868 82 Linux swap / Solaris /dev/sda2 513 29000 1830638880 83 Linux running samba memory: $ cat /proc/meminfo MemTotal: 255840 kB MemFree: 210980 kB Buffers: 5264 kB Cached: 22768 kB SwapCached: 0 kB Active: 20272 kB Inactive: 11448 kB HighTotal: 131072 kB HighFree: 99868 kB LowTotal: 124768 kB LowFree: 111112 kB SwapTotal: 32900860 kB SwapFree: 32900860 kB Dirty: 0 kB Writeback: 0 kB TIA!

  Read the article

• Installing SATA dvd burner on machine with no spare SATA ports/connectors

  - by Faheem Mitha

  Greetings. I have the following motherboard Tyan Thunder K8WE S2895A2NRF Motherboard - extended ATX - nForce Pro 2200/2050 - Socket 940 - UDMA133, Serial ATA-300 (RAID) - 2 x Gigabit Ethernet - FireWire - 6-1 channel audio This is part of a computer that was assembled in the winter of 2006/2007. The user manual says the following with regard to SATA Integrated SATAII Generation 1 Controllers (from NForce Professional 2200) Two integrated dual port SATA II controllers Four SATA connectors support up to four drives 3 Gb/s per direction per channel NvRAID v2.0 support Supports RAID 0, 1, 0+1 and JBOD. I just purchased a SATA DVD burner. Here is the page for the product http://www.amazon.ca/gp/product/B002QGDWLK/ The problem I am facing is that I already have 4 SATA drives installed. I don't want to remove any of them. However, I want the DVD burner above installed as well. The person I am consulting with here (Bombay, India) tells me that my four available SATA ports are filled, and that my only option is to install a SATA card into the one free PCI slot on the motherboard. However, he says that with this setup I will not be able to boot from the DVD drive. Are these statements correct, and what are my other options if any? Even it the statements in the last para are true, I suppose I could use one of the motherboard connectors/ports there are currently being used with the hard drives with the DVD drive, and use the "add-on" connector with one of the hard drives. Not all the 4 hard drives need to be bootable. BTW, despite having read through http://en.wikipedia.org/wiki/Serial_ATA#Cables.2C_connectors.2C_and_ports I am fuzzy on the differences between connectors, cables and ports. Thanks in advance.

  Read the article

• iSCSI, failover and XenServer

  - by jemmille

  I have an iSCSI fail over implementation setup so if one of my storage units fails the other takes over immediately (it also runs the NFS shares). When fail over occurs, volumes are exported, the IP is switched to the other machine and the targets are reconfigured. The fail over of the storage system itself works just fine. I use NexentaStor for my filer. When I do a test (manual) fail over of my storage the following occurs: Note: I run the admin VM's on NFS and customer based VM's on iSCSI All NFS based VM's remain up and working perfectly through the failover and after All VM 's running on iSCSI eventually report the following: An error about not being able to write to a particular block An error about journaling not working Then the file system goes RO To get the VM's working again I have to do the following: Force shutdown of the "broken" VM's. Detach the iSCSI SR Re-attach the iSCSI SR Boot the VM on a different server (5 in my pool) If I don't boot on a different server I get this error "Internal error: Failure("The VDI <uuid&gt; is already attached in RW mode; it can't be attached in RO mode!")" The only way I have found to fix that error is to reboot the entire server it was running on previously which is obviously a huge pain. Currently multipathing is NOT enabled (but can be and the same thing still occurs). I have edited much of the /etc/iscsid.conf file to work with the timeout settings but to no avail. In short, my storage fails over properly but XenServer does not keep the connection alive. As a thought, the error that shows up in #4 above might be the ultimate cause and fixing that would fix everything? Any help would be appreciated more than you know.

  Read the article

• ESXi 4.0 Guests Locking up

  - by Brendan Sherwin

  I installed ESXi 4.0 on an HP Proliant g5 with a 64bit Xeon processor and took advantage of the free license as I work for a public school. I created two instances of server 2003 from scratch, one to be the DC, DHCP, the other to be a file server and DNS/DHCP backup. I had both guests up and running fine, setup my user accounts, transferred the data, etc etc. Once I joined a client machine to the domain, I would find that both of my Windows guests would lock up. Sometimes it would be for five or so minutes, once it was overnight. The "locked up" state means that as far I could tell, all services were stopped; dhcp no longer handed out IP's, DNS stopped working, I couldn't RDP into the server. The ESXi host, my HP server, was still running fine. VSphere was working, and I could look at the performance of the individual guests.I would try Powering off the hosts from inside VSPhere, and the hosts would start powering off, but get stuck at 95%, and stay that way, sometimes only for 10 minutes, others for hours. Several times I had to restart ESXi from it's console in order to restart my machines. Now, can anyone tell me what is happening, and how I can fix it, or take steps to prevent it? I hired a consultant to come take a look at it, someone who's experience and knowledge I trust, and he told me he had never seen anything like this ever before. He spoke to a friend of his who is VM certified, and he also said he had never heard of this issue. Thanks for your replies, and I'll do my best to respond ASAP. Currently, the server is powered off, and I've reinstituted my nine year old Server 2000 boxes, and I'm considering installing ESXi 3.5. Does anyone know a host created in 4.0 will work in 3.5? I'd really like to avoid having to rebuild those accounts! I know 4.0 works on this server, as I have another server in another school with the same exact hardware running 4.0 fine. Brendan

  Read the article

• Apache + mod_fcgid + perl = error 500

  - by f-aminov

  Hi guys! I'm trying to setup Apache2.2 with mod_fcgid and libapache2-mod-perl2 with no luck. I've created a fcgi-bin directory in the root directory of my website and put there a test.fcgi file with the following content: #!/usr/bin/perl use CGI; print "This is test.fcgi!\n"; While trying to access it via http://www.website.dom/fcgi-bin/test.fcgi I get error 500 (Internal Server Error). Here is my vhost config: <VirtualHost 95.131.29.226:8080> ServerName website.com DocumentRoot /var/www/data/website.com SuexecUserGroup user group ServerAlias www.website.com AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml <Directory "/var/www/data/website.com/fcgi-bin/"> Options +ExecCGI Allow from all Order allow,deny AddHandler fcgid-script .fcgi </Directory> </VirtualHost> fcgid.conf: <IfModule mod_fcgid.c> AddHandler fcgid-script .fcgi SocketPath /var/lib/apache2/fcgid/sock IdleTimeout 3600 ProcessLifeTime 7200 MaxProcessCount 8 DefaultMaxClassProcessCount 2 IPCConnectTimeout 8 IPCCommTimeout 60 </IfModule> SuExec log: [2010-04-06 03:02:47]: uid: (500/equ) gid: (502/equ) cmd: test.fcgi Apache error log: test! test! [Tue Apr 06 03:02:51 2010] [notice] mod_fcgid: process /var/www/data/website.com/fcgi-bin/test.fcgi(26267) exit(communication error), terminated by calling exit(), return code: 0 [Tue Apr 06 03:02:53 2010] [notice] mod_fcgid: process /var/www/data/website.com/fcgi-bin/test.fcgi(26261) exit(server exited), terminated by calling exit(), return code: 0 I've no clue why I'm getting error 500, but when I'm trying to access this file using console ($ perl /var/www/data/website.com/fcgin-bin/test.fcgi) everthing works fine without any errors... Any suggestions on how to solve this problem would be greatly appreciated. Thank you!

  Read the article

• Cannot push to GitHub from Amazon EC2 Linux instance

  - by Eli

  Having the worst luck push files to a repo from EC2 to GitHub. I have my ssh key setup and added to Github. Here are the results of ssh -v [email protected] OpenSSH_5.3p1, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to github.com [207.97.227.239] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5github2 debug1: match: OpenSSH_5.1p1 Debian-5github2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'github.com' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug1: Offering public key: /root/.ssh/id_rsa debug1: Remote: Forced command: gerve eliperelman 81:5f:8a:b2:42:6d:4e:8c:2d:ba:9a:8a:2b:9e:1a:90 debug1: Remote: Port forwarding disabled. debug1: Remote: X11 forwarding disabled. debug1: Remote: Agent forwarding disabled. debug1: Remote: Pty allocation disabled. debug1: Server accepts key: pkalg ssh-rsa blen 277 debug1: Trying private key: /root/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey).

  Read the article

• MySQL replication - rapidly growing relay bin logs

  - by Rob Forrest

  Morning all, I've got a really strange situation here this morning much like a reportedly fixed MySQL bug. http://bugs.mysql.com/bug.php?id=28421 My relay bin logs are rapidly filling with an infinite loop of junk made of this sort of thing. #121018 5:40:04 server id 101 end_log_pos 15598207 #Append_block: file_id: 2244 block_len: 8192 # at 15598352 #121018 5:40:04 server id 101 end_log_pos 15606422 #Append_block: file_id: 2244 block_len: 8192 # at 15606567 ... # at 7163731 #121018 5:38:39 server id 101 end_log_pos 7171801 #Append_block: file_id: 2243 block_len: 8192 WARNING: Ignoring Append_block as there is no Create_file event for file_id: 2243 # at 7171946 #121018 5:38:39 server id 101 end_log_pos 7180016 #Append_block: file_id: 2243 block_len: 8192 WARNING: Ignoring Append_block as there is no Create_file event for file_id: 2243 These log files grow to 1Gb within about a minute before rotating and starting again. These big files are interspersed with 1 or 2 smaller files with just this in /*!40019 SET @@session.max_insert_delayed_threads=0*/; /*!50003 SET @OLD_COMPLETION_TYPE=@@COMPLETION_TYPE,COMPLETION_TYPE=0*/; DELIMITER /*!*/; # at 4 #121023 9:43:05 server id 100 end_log_pos 106 Start: binlog v 4, server v 5.1.61-log created 121023 9:43:05 BINLOG ' mViGUA9kAAAAZgAAAGoAAAAAAAQANS4xLjYxLWxvZwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAEzgNAAgAEgAEBAQEEgAAUwAEGggAAAAICAgC '/*!*/; # at 106 #121023 9:43:05 server id 100 end_log_pos 156 Rotate to mysqld-relay-bin.000003 pos: 4 DELIMITER ; # End of log file ROLLBACK /* added by mysqlbinlog */; /*!50003 SET COMPLETION_TYPE=@OLD_COMPLETION_TYPE*/; We're running a master-master replication setup with the problematic server running mysql 5.1.61. The other server which is, for the moment, stable is running 5.1.58. Has anyone got any ideas what the solution is to this and moreover, what might have caused this?

  Read the article

• Whats the difference between local and remote addresses in 2008 firewall address

  - by Ian

  In the firewall advanced security manager/Inbound rules/rule property/scope tab you have two sections to specify local ip addresses and remote ip addresses. What makes an address qualify as a local or remote address and what difference does it make? This question is pretty obvious with a normal setup, but now that I'm setting up a remote virtualized server I'm not quite sure. What I've got is a physical host with two interfaces. The physical host uses interface 1 with a public IP. The virtualized machine is connected interface 2 with a public ip. I have a virtual subnet between the two - 192.168.123.0 When editing the firewall rule, if I place 192.168.123.0/24 in the local ip address area or remote ip address area what does windows do differently? Does it do anything differently? The reason I ask this is that I'm having problems getting the domain communication working between the two with the firewall active. I have plenty of experience with firewalls so I know what I want to do, but the logic of what is going on here escapes me and these rules are tedious to have to edit one by one. Ian

  Read the article

• Trying to configure DNS on a Godaddy Virtual Dedicated host, Mediatemple Domain Registration [closed]

  - by dclowd9901

  A client of mine purchased VD hosting with Godaddy and a domain name with Mediatemple. I've never configured DNS from scratch, and I'm finding it very difficult to find any sort of explanation on how to go about it. As of right now, Mediatemple is pointing to the Godaddy's ns1.domaincontrol.com and ns2.domaincontrol.com nameservers. The VD hosting on Godaddy (via their Simple Control Panel) has options to "Add a new domain", which brings you through a wizard of sorts that asks you if the domain has already been registered (yes), what it is (dclowd9901.com for this example), create a system username and password for it (with checkboxes for SSH and FTP access), which level of user can administer it, and whether a mail account should be setup. When complete, it also creates a zone file. In this zone file, the Primary nameserver is ns1.dclowd9901.com; the records are as follow (where 12.23.12.34 is the presumed host): @ A 12.23.12.34 @ NS ns1 @ NS ns2 ns1 A 12.23.12.34 ns2 A 12.23.12.34 @ MX mail www A 12.23.12.34 ftp A 12.23.12.34 ssh A 12.23.12.34 mail A 12.23.12.34 If anyone can shed any light on this for me, explain to me the interactions between the registrar and the host and so on, I'd be very grateful. Thanks in advance for the help.

  Read the article

• Trouble serving vhosts when trying to set up wildcard subdomains with dnsmasq in local development e

  - by Jeremy Kendall

  I'm trying to get wildcard DNS enabled on my laptop using dnsmasq. I realize that this has been asked and answered more than once on this forum, but I can't get the solution to work for me. Steps taken so far: Installed dnsmasq Set address=/example.dev/127.0.0.1 in dnsmasq.conf Set listen-address=127.0.0.1 in dnsmasq.conf Ensured nameserver 127.0.0.1 is in /etc/resolv.conf Set prepend domain-name-servers 127.0.0.1; in /etc/dhcp3/dhclient.conf Created a vhost for example.dev Restarted apache and dnsmasq Note: example.dev is not set in /etc/hosts My vhost for example.dev <VirtualHost *:80> ServerName example.dev DocumentRoot /home/jkendall/public_html/example/public ServerAlias *.example.dev # This should be omitted in the production environment SetEnv APPLICATION_ENV development <Directory /home/jkendall/public_html/example/public> DirectoryIndex index.php AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> The setup above will server example.dev locally without any problem. It will also serve test.example.dev, but test.example.dev returns the default apache "It works!" index.html from /var/www rather than my index.php in /home/jkendall/public_html/example/public. The solution in this Server Fault thread suggests that address=/.example.dev/127.0.0.1 would resolve my problem, but when I try to use that solution, restarting dnsmasq results in a failure with the error message dnsmasq: error at line 62 of /etc/dnsmasq.conf For grins, I moved my project over to /var/www/example and modified the vhost appropriately. I got the same result as described above. At this point I'm not sure what other steps I can take to resolve the issue. Thoughts?

  Read the article

< Previous Page | 575 576 577 578 579 580 581 582 583 584 585 586  | Next Page >