Search Results

Search found 16415 results on 657 pages for 'computer'.

Page 580/657 | < Previous Page | 576 577 578 579 580 581 582 583 584 585 586 587  | Next Page >

• RouterLess, house-wired network using multiple powerline adapters

  - by Cliff Arnell

  related to the 'old days' of one ethernet cable tapped with Ts for each monitor.... my question might be very simple... or not. I have an over-the-air internet provider with a wire dish with a powered transceiver and cat5 cable out of the providers supplied modem. I'm presently connecting the output of the modem into my wireless router which sends the internet signal all over the house. Standard stuff, I believe. My Question. Can I just connect the output of the modem into 1 powerline adapter and tie all my equipment such as computer, printer, laptop, Tivo recorder, etc. into 1-each local powerline adapters located near each devices resulting in a 'house-wired' network and no router? I'm bothered by the idea that my over-the-air provider might be using something in my router to establish and keep my IP connection alive. I did have to configure the router for my IP, a router which, in my proposed scenario, would no longer exist. Thank you for your help.

  Read the article

• Terminal emulation has stopped working. Garbage escape chars

  - by oligofren

  To enable me to do some remote administration of our servers I started using a terminal emulation program called TouchTerm Pro on my iPhone. While not the smoothest experience, it has allowed me to leave my computer behind when going out of town, which makes the slightly painful experience worthwhile. As of late, the app unfortunately no longer works. Pressing up and down keys after logging on via ssh gives me garbage like ^[[A and ^[[B. Combinations with Ctrl - like you can see in the video - no longer works either. Writing full command lines and executing by the enter key works though. Being able to search my bash history was the difference between a usable app and endless frustration, so getting it to work is essential. The app has (of course) met its end of life, not getting updated anymore. I am not quite sure, which side (client or server) that has to be "fixed"/hacked to make the control sequences work again. But is there something I can do to make it work as intended? You can see a video of TouchTerm in operation here.

  Read the article

• UW-IMAP server, high load for one user

  - by Bruce Garlock

  We have been experiencing a very strange anomaly, with one specific user with our UW-IMAP server. We have about 75 users using the server, and one particular user, who is in about the middle as far as used storage keeps having issues with slow speed. Most of our users all use Thunderbird 2, or Thunderbird 3. Mostly 2, because of the performance issues we have had with 3. This user was on 3, and I downgraded him to 2. The performance has gotten better, but according to the imapd processes on the server, his username is using the most CPU % and CPU time. I've already done all the usual T/S'ing: Started profile from scratch, compacted folders, re-indexed, newer faster computer, etc.. Still, this users' imapd process is always using the most CPU on the server. For troubleshooting, we setup another user which has more usage, folders, etc.. than he does, but we don't see the users process taking up most of the CPU with the imapd process. So, it almost sounds like a particular email may be the culprit, but how can we find it, if thats the problem? This has been going on for a while, and he is a management person, so his patience is about to end. Does anyone have any ideas?

  Read the article

• Set up Linux box as WAP for MyBookLive?

  - by AcidFlask

  I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

  Read the article

• Why is my Mac not displaying anything to my LCD tv using HDMI?

  - by Pure.Krome

  Hi folks, I've got an iMac desktop computer. Love it. I wish to connect it to my LCD TV using HDMI. There is no HDMI output on the iMac so i had to buy one of these bad boys :- so now I can output video (via the mini Display Port) and sound (via USB) through this box, to my LCD. Works great ... with a single direct cable. I have another 3 or 5 metre cable inserted into my wall, so i do not have to have a silly hdmi cable floating in the air between my iMac and my LCD TV. When I do this, there is no picture. To better explain all of this, i made a quick video explaining my problem in detail, so you can exactly see what is going on/wrong. I've also tried changing the output format for the TV from 1080i down to 720p and even lower .. incase the cable in the wall doesn't allow 1080i. here's the video with the full explanation :- http://www.youtube.com/watch?v=ZkKRKnRIh6Q (NOTE: I incorrectly said in the video that the hidden wall cable is 10 metres long. me == fail. It's 3m or 5m...). Can someone please watch it and suggest some ideas to getting it working?

  Read the article

• Should I keep my ex-employer's data?

  - by Jurily

  Following my brief reign as System Monkey, I am now faced with a dilemma: I did successfully create a backup and a test VM, both on my laptop, as no computer at work had enough free disk space. I didn't delete the backup yet, as it's still the only one of its kind in the company's history. The original is running on a hard drive in continuous use since 2006. There is now only one person left at the company, who knows what a backup is, and they're unlikely to hire someone else, for reasons very closely related to my departure. Last time I tried to talk to them about the importance of backups, they thought I was threatening them. Should I keep it? Pros: I get to save people from their own stupidity (the unofficial sysadmin motto, as far as I know) I get to say "I told you so" when they come begging for help, and feel good about it I get to say nice things about myself on my next job interview Nice clean conscience Bonus rep with the appropriate deities Cons: Legal problems: even if I do help them out with it, they might just sue me for keeping it anyway, although given the circumstances I think I have a good case Legal problems: given the nature of the job and their security, if something leaks, I'm a likely target for retaliation Legal problems: whatever else I didn't think about I need more space for porn. Legal problems. What would you do?

  Read the article

• Windows 7 Install: No drives were found

  - by Albert Bori

  I was building a computer for my wife with an older SATA hard drive that I had lying around, and when attempting to do a new install of Windows 7 on it, the installer says: "No drives were found. Click Load Driver to provide a mass storage driver for installation." I ran the diskpart command: list volume, and it showed up as "Raw". So, I formatted it to NTFS and then it showed up as a healthy drive in diskpart. I also ran check disk on it with no errors. Windows 7 installer STILL can't find the drive. As far as BIOS settings, I have tried "Native IDE", AHCI, and Both AHCI/IDE mode (SATA slots 0-2 AHCI, 3-4 IDE). I tried all combinations... still "no drives were found". At this point, I'm just scratching my head. Using the installation dos window, I can see and talk to the drive just fine, but the installer just doesn't see it at all. I've even written folders and files to the drive, and it still "can't be seen". Any help would be great. Items of interest: Motherboard model: Gigabyte GA-A75M-UD2H - BIOS Version F5 (latest) Hard drive model: 80GB Seagate Barracuda 7200.7 ST380817AS (no other drives) Installing Windows 7 using a FAT32 formatted USB Drive, which I've used for other installs

  Read the article

• For Windows XP: How to uninstall Broadcom Bluetooth software that won't disappear

  - by T. Webster

  Hello, my situation is similar to this question for Windows 7, except my OS is Windows XP SP3. I have recently realized I made the mistake of buying a Bluetooth adapter and installing the Broadcom/Widcomm Bluetooth stack driver software. Now that I know that the software is no good, I want to install it (so I can install the Toshiba stack for the Cirago adapter). I've attempted to uninstall all Bluetooth driver software in Device Manager, and I don't see any remnants of any Bluetooth drivers there. I would include pictures here, but I don't have 10 reputation yet, so I'll just use links instead. picasaweb.google.com/lh/photo/2NAos6BP9UigPtJKaYRGyQ?feat=directlink But I do see that the little Bluetooth icon still persists: picasaweb.google.com/lh/photo/kbxgPP8ZLxhjX4ob2YjSew?feat=directlink I don't see anything about Bluetooth, Broadcom, or Widcomm in Add/Remove Programs. I don't see any folder names Broadcom or Widcomm in Program Files folder, either. But I do see that Broadcom does show up in the registry with respect to Bluetooth, as shown here. picasaweb.google.com/lh/photo/hWDo-OzB8ApibzeHA_saxQ?feat=directlink What should I do now to completely wipe this persistent Broadcom Bluetooth software off my computer?

  Read the article

• Netgear router is not resolving hostnames

  - by Thomas Clayson

  Not sure what the problem is, but I am used to being able to access other clients on my LAN via their hostname. We got a new router from plusnet (Netgear WNR1000v3) and now this has stopped working. For instance, if I were to run a web server from one computer with the hostname TomPC usually I could go into a browser and type http://TomPC and I would get the web server front page. I can access it by using the LAN ip of the machine. e.g. http://192.168.1.1 works fine. I thought it would be a simple option in the admin panel of the router - possibly I had to turn on DNS/DCHP or something. But I can't see anything, and my searches on the internet seem to turn up ridiculous solutions involving setting up a dedicated DNS server on my LAN. This is just a small home network - really I just want to be able to access my Raspberry PI on the network without having to work out the IP address every time. (I know I could just set a static IP address for it, but using its hostname would be much easier). DCHP is enabled in the LAN settings part, although RIP is disabled (I don't know what the latter is) I don't know if this has anything to do with it? Many thanks!

  Read the article

• Manual NAT on Checkpoint (Redirect all http requests to a local web server)

  - by kulakli

  Hi, We have a proxy server in internal network and I want to redirect all internet http requests to a web server in local network. It'll be like a Network Billboard that say "No direct connection is available. Set up your proxy etc." For example: A user starts the computer Opens the browser Trys to open www.google.com Should see web server output on local network Trys another web site on internet Should see web server output on local network Sets up proxy Trys to connect to a web site Web site should be loaded I have added a simple manual NAT rule to address translation in Checkpoint firewall but it simply does not work. Here is my address translation rule Source Destination Service T.Source T.Destination T.Service MY_PC A_GOOGLE_IP ALL ORIGINAL INT_WEB_SRV ORIGINAL Then when I ping A_GOOGLE_IP, replies come from INT_WEB_SRV, as I expected. However, when I try to connect A_GOOGLE_IP from browser (http://A_GOOGLE_IP), No replies come from SYN_SENT and falls into timeout. When I look at the firewall log of INT_WEB_SRV, I can see the incoming connection requests from MY_PC is accepted and NO denies. By the way, there is no problem to see INT_WEB_SRV (http://INT_WEB_SRV) from browser. My understanding is, my nat rule at checkpoint NGX R60 does not include return packets. I definitely need some help. Regards, Burak

  Read the article

• Windows 7: Wi-Fi connection drops intermittently - only returns after "Troubleshoot connection" resets the adapter

  - by sleske

  On our laptop (running Windows 7) the Wi-Fi connection drops intermittently. Symptoms: Connectivity is suddenly lost, and the "signal strenght" indicator in the tray shows zero strength and a yellow "star" symbol. What happens then: The problem does not resolve itself by just waiting. If I click on the tray icon, the "Windows network diagnostics" wizard pops up and tells me that there is a networking problem (duh). If I click on the "repair" button (not sure about the wording), the wizard works for a while, then reports that it has reset the network adapter. Then Wi-Fi works again. While the above procedure has worked every time so far, it is very annoying. It takes 10-20s to repair the connection, and in the meantime downloads, video streams etc. may have been aborted. Some more details: The problem occurs without any apparent regularity, but usually a few minutes after powerup (though not every time). It happens frequently enough to be annoying. It is unlikely to be a router problem - another laptop running at the same time usually has no Wi-Fi problems. I am at a loss about what to try to troubleshoot this. Any ideas? Computer: Acer Aspire 7739Z. Wi-Fi card: Atheros AR5B125

  Read the article

• Ubuntu in failed state after upgrade from 10.04 to 10.10 - How to recover?

  - by Harvey

  I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: 1. Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a). 2. gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok] 3. gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ... What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

  Read the article

• Can I share my cable internet connection through my ADSL wireless router?

  - by Roaders

  Hi All Over the xmas period I am at my in-laws. They have Virgin Broadband (cable) and have a basic modem / router that is plugged directly into their computer using an ethernet cable. My wife and I arrived with 5 PCs! (ok, one is a gift and won't be used) 4 of which are laptops so I would like to be able to use their internet connection. At the moment I am working so have plugged the ethernet cable into my work laptop. Rebooting the router meant that my work laptop now has internet. I have my ADSL Netgear router which is wireless. I tried plugging it in between the router and the PC but I didn't seem to be able to share the internet connection wirelessly. The original PC still had internet despite ony being connected to my router but my wireless laptop didn't have a connection. My old cable router had an internet ethernet port on the back that the modem plugged into. My ADSL router doesn't, it has a phone connection socket. Is there a way of doing what I want with the equipment I have? Thanks

  Read the article

• Delayed internet access

  - by Joel Coel

  When I (and presumably my users) first start up or log in to my computer I can't get internet access until several minutes after logging in. Internet pages like serverfault.com will time out. During this time I can access internal web servers. Sometimes pinging the gateway seems to fix the problem. I'm using Windows 7 on this machine with wifi, and the problem seems limited to the wifi network, which is on a separate vlan. The wired network does not share the problem, but I know it's not the wifi connection itself because the internal sites work. The wifi access point is attached to a 3Com 4200 switch, with the port set for vlan 2 untagged, vlan 1 tagged. The 4200 has a fiber connection to a 3Com 4900SX fiber switch that acts almost as a router here. The fiber connection is vlan 1 untagged vlan 2 tagged at both ends. The gateway is then attached to a different 4200 (vlan 1 untagged, vlan 2 tagged) that has a similar fiber connection to the 4900SX. vlan 2 has 192.168.8.0/22 IPs, vlan 1 has 10.1.0.0/16 IPs. The 4900SX has an interface for both vlans (10.1.1.1/192.168.8.1), as does the gateway (10.1.1.5/192.168.8.5). There is one dchp server for both vlans on the same switch as the gateway. It chooses a dhcp scope based on the interface used by the 4900sx to forward the dhcp request. There is also a network access list on the 4900sx set to deny all vlan2 traffic to any 10.1.x.x host, with exceptions made for a few servers, including dhcp, 4900sx, and the gateway. I think that about covers it. Any ideas on why internet access would be delayed like this?

  Read the article

• Simple electric DC question. Current consumption

  - by Bobb

  Suppose you have DC power supply and a consumer connected to it (i.e. computer PSU and a hard drive). Suppose PSU which was supplied with the consumer has output 5V 1A. So I assume that the consumer should not consume more than 1A. Suppose the original PSU is broken now and I want to replace it with the one I have which is 5V 10A. My guess is that current is something which depends on the consumer. So if the consumer consumes normally 1A then it will not consume more than that even if it is connected to 10A PSU. In other word - am I right assuming that the consumer will not burn out being connected to a power supply with higher current output? P.S. my understanding is that voltage is something independent from the consumer. If you give it higher voltage it will burn (voltage is from PSU to the consumer). However current must be in opposite - consumer sucks as much current as it need not as much as PSU can provide (of course given that max PSU current is greater than the consumer needs)

  Read the article

• A little guidance setting up FTP server authentication on Windows Server 2008 R2 standard?

  - by Ropstah

  I have a (clean) server running Windows Server 2008 R2 standard. I would just like to use it for serving a website and a FTP server through IIS. IIS is installed and serves my website propery. I have now added a FTP site but when I try to logon using my user/pass i get the following error: 530 User cannot login From this article (http://support.microsoft.com/kb/200475) I understand that these four causes can be pointed out: The Allow only anonymous connections security setting has been turned on in the Microsoft Management Console (MMC). Not the case The username does not have the Log on locally permission in User Manager. The user is in the Users group, however I'm not able to logon through RDP. I tried configuring this by following this article through GPMC however this only works when I'm logged in as a domain user on a domain controller which I'm not: I'm logged in as administrator The username does not have the Access this computer from the network permission in User Manager. Not sure what this implies...? The Domain Name was not specified together with the username (in the form of DOMAIN\username). Tried adding the server name: server\username, not working... I am an absolute server noob and I'd just like to be able to connect through FTP... Any guidance is highly appreciated!

  Read the article

• How to connect via SSH to a linux mint system that is connected via OpenVPN

  - by Hilyin

  Is there a way to make SSH port not get sent through VPN so when my computer is connected to a VPN, it can still be remoted in via SSH from its non-VPN IP? I am using Mint Linux 13. Thank you for your help! This is the instructions I followed to setup the VPN: Open Terminal Type: sudo apt-get install network-manager-openvpn Press Y to continue. Type: sudo restart network-manager Download BTGuard certificate (CA) by typing: sudo wget -O /etc/openvpn/btguard.ca.crt http://btguard.com/btguard.ca.crt Click on the Network Manager icon, expand VPN Connections, and choose Configure VPN A Network Connections window will appear with the VPN tab open. Click Add. 8. A Choose A VPN Connection Type window will open. Select OpenVPN in the drop-down menu and click Create.. . In the Editing VPN connection window, enter the following: Connection name: BTGuard VPN Gateway: vpn.btguard.com Optional: Manually select your server location by using ca.vpn.btguard.com for Canada or eu.vpn.btguard.com for Germany. Type: select Password User name: username Password: password CA Certificate: browse and select this file: /etc/openvpn/btguard.ca.crt Click Advanced... near the bottom of the window. Under the General tab, check the box next to Use a TCP connection Click OK, then click Apply. Setup complete! How To Connect Click on the Network Manager icon in the panel bar. Click on VPN Connections Select BTGuard VPN The Network Manager icon will begin spinning. You may be prompted to enter a password. If so, this is your system account keychain password, NOT your BTGuard password. Once connected, the Network Manager icon will have a lock next to it indicating you are browsing securely with BTGuard.

  Read the article

• How to make a Windows Vista boot / recovery cd from a running system without using an original CD / DVD

  - by Giorgio

  I have just repaired a friends computer (replaced motherboard) and now I am trying to repair the Windows (Windows Vista) partitions. Unfortunately, probably due to the fact that he tried to start it several times after the old motherboard had stopped working (no signal on video) now the partition table or the file systems (or both?) appear to be damaged. I managed to boot Windows a couple of times but could not complete the boot. I tried to repair the partition table and file systems using Linux RIP (booting from USB stick) but the Linux utilities say that the file system is damaged and I should run chkdsk /f from Windows. So I now need a Windows boot CD from which I can boot and run chkdsk or any other Windows utilities that can repair the file system. Is there an easy way to create such a CD? Or can I download it for free somewhere? All the links to Windows Vista boot / repair CD's I have found on the internet refer to non-free stuff. Any hint? EDIT I have a working laptop with Windows Vista installed. So one solution would be to make a bootable CD or USB from it so that I can boot the desktop and run the repair utilities. However, I do not have the Windows Vista installation DVD, because both computers were bought with Windows pre-installed.

  Read the article

• Limiting bandwith on an Windows 7 machine

  - by Mihai Damian

  I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

  Read the article

• Proxy auto-config dnsResolve doesn't seem to resolve subdomains

  - by HorusKol

  We're running on a Windows domain, and have a DNS to control computer names on our intranet. The following PAC works great for basic hostnames on our intranet - but we're setting up some subdomain-like names (example, redesign.buildbox), and it isn't resolving these. These subdomains are resolvable through other means (such as nslookup). Other than checking to see if the host has ".buildbox" or other domain, is there a way to make it work? Maybe I could try appending the Windows domain to host (can you concatenate strings in a PAC)? function FindProxyForURL(url, host) { // If IP address is internal or hostname resolves to internal IP, send direct. var resolved_ip = dnsResolve(host); if (isInNet(resolved_ip, "129.2.2.0", "255.255.255.128")) return "DIRECT"; if (isInNet(resolved_ip, "10.1.1.0", "255.255.255.0")) return "DIRECT"; if (isInNet(resolved_ip, "150.1.2.0", "255.255.255.248")) return "DIRECT"; // All other traffic uses below proxies, in fail-over order. return "PROXY 192.111.222.111:8080; DIRECT"; }

  Read the article

• openvpn port 53 bypasses allows restrictions ( find similar ports)

  - by user181216

  scenario of wifi : i'm using wifi in hostel which having cyberoam firewall and all the computer which uses that access point. that access point have following configuration default gateway : 192.168.100.1 primary dns server : 192.168.100.1 here, when i try to open a website the cyberoam firewall redirects the page to a login page (with correct login information, we can browse internet else not), and also website access and bandwidth limitations. once i've heard about pd-proxy which finds open port and tunnels through a port ( usually udp 53). using pd-proxy with UDP 53 port, i can browse internet without login, even bandwidth limit is bypassed !!! and another software called openvpn with connecting openvpn server through udp port 53 i can browse internet without even login into the cyberoam. both of softwares uses port 53, specially openvpn with port 53, now i've a VPS server in which i can install openvpn server and connect through the VPS server to browse internet. i know why that is happening because with pinging on some website(eb. google.com) it returns it's ip address that means it allows dns queries without login. but the problem is there is already DNS service is running on the VPS server on port 53. and i can only use 53 port to bypass the limitations as i think. and i can not run openvpn service on my VPS server on port 53. so how to scan the wifi for vulnerable ports like 53 so that i can figure out the magic port and start a openvpn service on VPS on the same port. ( i want to scan similar vulnerable ports like 53 on cyberoam in which the traffic can be tunneled, not want to scan services running on ports). improvement of the question with retags and edits are always welcomed... NOTE : all these are for Educational purpose only, i'm curious about network related knowledge.....

  Read the article

• openvpn port 53 bypasses allows restrictions ( find similar ports)

  - by user181216

  scenario of wifi : i'm using wifi in hostel which having cyberoam firewall and all the computer which uses that access point. that access point have following configuration default gateway : 192.168.100.1 primary dns server : 192.168.100.1 here, when i try to open a website the cyberoam firewall redirects the page to a login page (with correct login information, we can browse internet else not), and also website access and bandwidth limitations. once i've heard about pd-proxy which finds open port and tunnels through a port ( usually udp 53). using pd-proxy with UDP 53 port, i can browse internet without login, even bandwidth limit is bypassed !!! and another software called openvpn with connecting openvpn server through udp port 53 i can browse internet without even login into the cyberoam. both of softwares uses port 53, specially openvpn with port 53, now i've a VPS server in which i can install openvpn server and connect through the VPS server to browse internet. i know why that is happening because with pinging on some website(eb. google.com) it returns it's ip address that means it allows dns queries without login. but the problem is there is already DNS service is running on the VPS server on port 53. and i can only use 53 port to bypass the limitations as i think. and i can not run openvpn service on my VPS server on port 53. so how to scan the wifi for vulnerable ports like 53 so that i can figure out the magic port and start a openvpn service on VPS on the same port. ( i want to scan similar vulnerable ports like 53 on cyberoam in which the traffic can be tunneled, not want to scan services running on ports). improvement of the question with retags and edits are always welcomed... NOTE : all these are for Educational purpose only, i'm curious about network related knowledge.....

  Read the article

• Power Outage Interrupted Upgrade from Windows Vista Ultimate to 7 Ultimate, Reverted to Vista, Now Vista is failing... What Next?

  - by tednewk

  I was in the midst of what seemed to be a successful upgrade from Vista Ultimate to 7 Ultimate when there was a brief blackout. The upgrade failed and Windows reverted back to Vista. Now Vista is very slow to boot, has problems waking back-up from inactivity and quickly loses it's wireless connection. The wake-up problem manifests itself as the mouse is clearly shown on a black screen but I have no access to the Desktop or Taskbar or Explorer. Even Alt-Ctrl-Delete doesn't seem to work. No task menu, no reboot. Hitting the reset button reboots the machine with the usual Black Screen warnings offering Safe Mode. I tried to do a system restore to a point before the upgrade. That didn't seem to work. My guess is that my system is a mutant with parts of Vista and parts of 7 crashing each other. I would like avoid a clean install if at all possible to avoid reinstalling other software. What should I try now? My thoughts are: My a system back-up to lock the computer in place Trying a second 7 upgrade If that appears to be working make another back-up If not reload back-up and try a repairing Vista from DVD. If that appears to work make another back-up, let system stablize about a week then try 7 install again If that doesn't work are there any other options to try before settling for a clean install? Another complication, I am doing this by "remote control". I'm traveling with my job and I'll be talking my son through it over the phone. (Kind of like the landing the 747 cliche from all the 70's adventure shows!) So is there a way of simplifying the steps? Thanks Ted

  Read the article

• Sharepoint Central Administration stuck / high CPU usage

  - by johnnyb10

  I'm using WSS 3 and I recently added a new web application to my SharePoint Server. After adding it, I wasn't able to open the Central Administration site. I also noticed that there was a w3wp.exe error (Event ID 1000) in the Event Viewer. The situation now is that the w3wp.exe process is hovering around 50% CPU usage continuously. I installed a program called IIS Peek, and it shows continuous GET requests on the Central Administration site; this happens even if I stop the Central Administration site in IIS. The IP addresses identified in the GET request is my workstation, which is what I used to attempt to access Central Administration after I created the new web application. Can someone explain what's going on and how I might fix it? It seems as if my computer tried to access Central Administration and then it hung, but the page requests that were happening at the time are somehow continuing over and over again. So my two problems are the inability to access Central Administration, and the CPU Usage of w3wp.exe, which I'm assuming are two symptoms of the same problem. I'd like to know if there's anything I can do besides restarting IIS, because we have clients accessing other sites on this server. Thanks.

  Read the article

• Can't connect to Server Manager from Windows 7

  - by SAdmin317

  I have a Windows 7 Pro 64bit with SP1 desktop that has RSAT tools installed. I opened Server Manager and can't connect to the server (Server 2008 R2 core). I followed the guide to enable everything on the server, added a registry key to enable read-only on the device manager as well. On the Windows 7 PC I turned on winrm, did the quick config, and added the server IP and name as trusted hosts. I still get an error when connecting. "Connecting to the remote server failed with the following error message: The WinRM client cannot process the requests. If the authentication scheme is different from Kerberos, or if the client computer is not joined to a domain, then HTTPS transport must be used or the destination machine must be added to the TrustedHosts configuration setting...." I also added the name of the server to the windows 7 /etc/hosts file. Ping the server name translates to the IP of the server. Also opened up the firewall for "Remote Volume Management" Both machines are on the same Workgroup, using the same Administrator account, with the same password. Any help appreciated.

  Read the article

< Previous Page | 576 577 578 579 580 581 582 583 584 585 586 587  | Next Page >