Search Results

Search found 18808 results on 753 pages for 'security updates'.

Page 592/753 | < Previous Page | 588 589 590 591 592 593 594 595 596 597 598 599  | Next Page >

• Windows 2003 Domain Controller Very Upset about NIC Teaming

  - by Kyle Brandt

  I set up BACS (Broadcom Teaming) to team two NIC on a Windows 2003 Active Directory Domain Controller. Networking still works okay, I can ping the gateway etc, but both DNS and Active Directory fail to start with various 40xx errors. The team that I created is Smart load Balancing with Failover, with one backup and only one in smart load balancing (So really it is just failover). I have the team the same IP address that the single active NIC had before. Anyone seen this before, or have any ideas what the problem might be? Event Type: Error Event Source: DNS Event Category: None Event ID: 4015 Date: 3/7/2010 Time: 10:33:03 AM User: N/A Computer: ADC Description: The DNS server has encountered a critical error from the Active Directory. Check that the Active Directory is functioning properly. The extended error debug information (which may be empty) is "". The event data contains the error. Event Type: Error Event Source: DNS Event Category: None Event ID: 4004 Date: 3/7/2010 Time: 10:33:03 AM User: N/A Computer: ADC Description: The DNS server was unable to complete directory service enumeration of zone .. This DNS server is configured to use information obtained from Active Directory for this zone and is unable to load the zone without it. Check that the Active Directory is functioning properly and repeat enumeration of the zone. The extended error debug information (which may be empty) is "". The event data contains the error. Event Type: Error Event Source: NTDS Replication Event Category: DS RPC Client Event ID: 2087 Date: 3/7/2010 Time: 10:40:28 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: ADC Description: Active Directory could not resolve the following DNS host name of the source domain controller to an IP address. This error prevents additions, deletions and changes in Active Directory from replicating between one or more domain controllers in the forest. Security groups, group policy, users and computers and their passwords will be inconsistent between domain controllers until this error is resolved, potentially affecting logon authentication and access to network resources.

  Read the article

• How to use Salt Stack with minions all behind NAT (not publicly accessible, default salt ports not open)?

  - by MountainX

  Can Salt Stack minions communicate with the salt master from behind NAT/Firewalls, etc., using standard ports that would be open be default in all consumer NAT routers (and without the minions having a public DNS record or static IP)? I'm working my way through my first salt tutorial, and this is where I'm stuck. I am able to configure iptables on the Ubuntu salt-master. But I have no control over the routers/NAT that the minions will sit behind. So far I tried these settings: /etc/salt/master: publish_port: 465 ret_port: 443 /etc/salt/minion: master_port: 465 That did not work. Background: I have a custom developed application presently running on about 40 Kubuntu laptops (& more planned). Every few months I have to update the application. (Often this just amounts to replacing a .jar file, which requires root permissions.) I also have to run Ubuntu updates and a few other minor things. I've been doing it manually, one by one, using Team Viewer to log into each client. I would like to dramatically improve this process. The two options I'm aware of are either: use reverse ssh tunnels and bash scripts. I tested this and it works. But I don't get any of the reporting, etc., I would get with Salt Stack. use Salt Stack (or similar) management tool. But I need a really simple tool. I can't invest any time in a big learning curve. I looked at Puppet and a bunch of related tools. The only one I found that looked simple enough for me (so far) was Salt Stack. But I'm stuck now because my minion can't reach the salt-master, as stated above. I appreciate suggestions.

  Read the article

• FreeBSD performance tuning. Sysctls, loader.conf, kernel.

  - by SaveTheRbtz

  I wanted to share knowledge of tuning FreeBSD via sysctls, so i'm posting them with comments. Based on Igor Sysoev (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Sysctls are for 7.x FreeBSD. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. Highload web server sysctls: # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Do not use lager sockbufs on 8.0 # ( http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=262144 # Recive clusters (on amd64 7.2+ 65k is default) # For such high value vm.kmem_size must be increased to 3G #kern.ipc.nmbclusters=229376 # Jumbo pagesize(4k/8k) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=192000 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=24000 #kern.ipc.nmbjumbo16=10240 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # Turn off receive autotuning #net.inet.tcp.recvbuf_auto=0 # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This should be enabled if you going to use big spaces (>64k) #net.inet.tcp.rfc1323=1 # Turn this off on highspeed, lossless connections (LAN 1Gbit+) #net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # You can try setting it to 0 on fileserver with 1GBit+ interfaces # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) #net.inet.tcp.inflight.enable=0 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't tested it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds (default: 30000 from RFC) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=40960 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becames lower) vfs.ufs.dirhash_maxmem=67108864 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 /boot/loader.conf: # Accept filters for data, http and DNS requests # Usefull when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load= #siis_load= # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 200M) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=100 # Incresed hostcache net.inet.tcp.hostcache.hashsize="16384" net.inet.tcp.hostcache.bucketlimit="100" # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # `sysctl dev.em.0.stats=1 ; dmesg` # #Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # Nicer boot logo =) loader_logo="beastie" And finally here is my additions to GENERIC kernel # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU of 8K(amd64) # (4k for i386). This req. is only for receiving data. # Read more in man zero_copy_sockets #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL options IPFIREWALL_VERBOSE options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_DEFAULT_TO_ACCEPT options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron #device amdtemp # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # DTrace options KDTRACE_HOOKS # all architectures - enable general DTrace hooks options DDB_CTF # all architectures - kernel ELF linker loads CTF data #options KDTRACE_FRAME # amd64-only # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (9.x+) #options TEKEN_UTF8 #options TEKEN_XTERM # NCQ support # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ #options ATA_CAM # FreeBSD 9+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html #options DEADLKRES PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

  Read the article

• Telnet does not give a response

  - by floorish

  Some wireless access points are acting a little weird, so I want to reboot them every couple of hours. Luckily there exists a security flaw which lets me login as root through telnet when using port 1111 (without username and password). Now I want to use that to let my QNAP NAS execute the reboot command through telnet every now and then. The problem is however that that telnet version doesn't give any response if I connect to the AP. The telnet I use on OSX works just fine but the one on the NAS not. BusyBox v1.01 (2012.06.14-18:35+0000) multi-call binary Usage: telnet [-a] [-l USER] HOST [PORT] When I execute telnet <HOST> 1111 nothing happens. I can send the escape character ^] which gives me the following options: Console escape. Commands are: l go to line mode c go to character mode z suspend telnet e exit telnet The only way to get some commands executed is by suspending telnet with z followed by some random command which isn't recognized. Then the prompt shows this: # telnet 192.168.1.5 1111 ^] Console escape. Commands are: l go to line mode c go to character mode z suspend telnet e exit telnet z continuing... asdf Illegal command. 00> After that I am able to communicate with the AP, but when I exit the telnet session and try the same again, the AP refuses to connect at all and it must be manually rebooted (looks like the telnet session isn't shut down properly on the AP). So the question is what commands should I execute in order to communicate with the AP using the Busybox telnet version of the QNAP? (No, can't use ssh unfortunately)

  Read the article

• Avoiding DNS timeouts when a dns server fails

  - by user65124

  Hi there. We have a small datacenter with about a hundred hosts pointing to 3 internal dns servers (bind 9). Our problem comes when one of the internal dns servers becomes unavailable. At that point all the clients that point to that server start performing very slowly. The problem seems to be that the stock linux resolver doesn't really have the concept of "failing over" to a different dns server. You can adjust the timeout and number of retries it uses, (and set rotate so it will work through the list), but no matter what settings one uses our services perform much more slowly if a primary dns server becomes unavailable. At the moment this is one of the largest sources of service disruptions for us. My ideal answer would be something like "RTFM: tweak /etc/resolv.conf like this...", but if that's an option I haven't seen it. I was wondering how other folks handled this issue? I can see 3 possible types of solutions: Use linux-ha/Pacemaker and failover ips (so the dns IP VIPs are "always" available). Alas, we don't have a good fencing infrastructure, and without fencing pacemaker doesn't work very well (in my experience Pacemaker lowers availability without fencing). Run a local dns server on each node, and have resolv.conf point to localhost. This would work, but it would give us a lot more services to monitor and manage. Run a local cache on each node. Folks seem to consider nscd "broken", but dnrd seems to have the right feature set: it marks dns servers as up or down, and won't use 'down' dns servers. Any-casting seems to work only at the ip routing level, and depends on route updates for server failure. Multi-casting seemed like it would be a perfect answer, but bind does not support broadcasting or multi-casting, and the docs I could find seem to suggest that multicast dns is more aimed at service discovery and auto-configuration rather than regular dns resolving. Am I missing an obvious solution?

  Read the article

• YUM Update Failed - Error in POSTIN scriptlet in rpm package

  - by Tiffany Walker

  Running "yum update" and it gets to installing and then breaks. Not sure what the problem is. Google shows nothing. Error in POSTIN scriptlet in rpm package gtk2-2.18.9-10.el6.x86_64 error: error creating temporary file /var/tmp/rpm-tmp.NB84HC: Invalid argument error: Couldn't create temporary file for %post(gtk2-2.18.9-10.el6.x86_64): Invalid argument Updating : e2fsprogs-libs-1.41.12-12.el6.x86_64 44/378 Traceback (most recent call last): File "/usr/lib/python2.6/site-packages/yum/rpmtrans.py", line 387, in callback self._instCloseFile( bytes, total, h ) File "/usr/lib/python2.6/site-packages/yum/rpmtrans.py", line 463, in _instCloseFile self.base.history.trans_data_pid_end(pid, state) File "/usr/lib/python2.6/site-packages/yum/history.py", line 858, in trans_data_pid_end """, ('TRUE', self._tid, pid, state)) File "/usr/lib/python2.6/site-packages/yum/sqlutils.py", line 168, in executeSQLQmark return cursor.execute(query, params) sqlite3.OperationalError: unable to open database file error: python callback <bound method RPMTransaction.callback of <yum.rpmtrans.RPMTransaction instance at 0x45c2290>> failed, aborting! With a check all: yum check Loaded plugins: fastestmirror, rhnplugin, security MySQL-client-5.5.27-1.cp.1132.x86_64 is obsoleted by MySQL-client-5.5.27-1.cp.1132.x86_64 MySQL-server-5.5.27-1.cp.1132.x86_64 is obsoleted by MySQL-server-5.5.27-1.cp.1132.x86_64 abrt-libs-2.0.8-6.el6.x86_64 is a duplicate with abrt-libs-2.0.4-14.el6.centos.x86_64 audit-libs-2.2-2.el6.x86_64 is a duplicate with audit-libs-2.1.3-3.el6.x86_64 bandmin-1.6.1-5.noarch has missing requires of perl(bandmin.conf) bandmin-1.6.1-5.noarch has missing requires of perl(bmversion.pl) bandmin-1.6.1-5.noarch has missing requires of perl(services.conf) 32:bind-libs-9.8.2-0.10.rc1.el6_3.3.x86_64 is a duplicate with 32:bind-libs-9.7.3-8.P3.el6_2.2.x86_64 cagefs-safebin-3.6-6.el6.cloudlinux.x86_64 is a duplicate with cagefs-safebin-3.5-1.el6.cloudlinux.x86_64 chkconfig-1.3.49.3-2.el6.x86_64 is a duplicate with chkconfig-1.3.49.3-1.el6_2.x86_64 cloudlinux-release-6-6.3.0.x86_64 is a duplicate with cloudlinux-release-6-6.2.2.x86_64 coreutils-8.4-19.el6.x86_64 is a duplicate with coreutils-8.4-16.el6.x86_64 coreutils-libs-8.4-19.el6.x86_64 is a duplicate with coreutils-libs-8.4-16.el6.x86_64 1:cups-libs-1.4.2-48.el6_3.1.x86_64 is a duplicate with 1:cups-libs-1.4.2-44.el6_2.3.x86_64 1:dbus-libs-1.2.24-7.el6_3.x86_64 is a duplicate with 1:dbus-libs-1.2.24-5.el6_1.x86_64 12:dhcp-common-4.1.1-31.P1.el6_3.1.x86_64 is a duplicate with 12:dhcp-common-4.1.1-25.P1.el6_2.1.x86_64 e2fsprogs-libs-1.41.12-12.el6.x86_64 is a duplicate with e2fsprogs-libs-1.41.12-11.el6.x86_64 exim-4.80-0.x86_64 has missing requires of perl(SafeFile) expat-2.0.1-11.el6_2.x86_64 is a duplicate with expat-2.0.1-9.1.el6.x86_64 frontpage-2002-SR1.2.i386 has missing requires of libexpat.so.0 gawk-3.1.7-10.el6.x86_64 is a duplicate with gawk-3.1.7-9.el6.x86_64 glib2-2.22.5-7.el6.x86_64 is a duplicate with glib2-2.22.5-6.el6.x86_64 glibc-2.12-1.80.el6_3.5.x86_64 is a duplicate with glibc-2.12-1.47.el6_2.12.x86_64 glibc-common-2.12-1.80.el6_3.5.x86_64 is a duplicate with glibc-common-2.12-1.47.el6_2.12.x86_64 gtk2-2.18.9-10.el6.x86_64 is a duplicate with gtk2-2.18.9-6.el6.centos.x86_64 kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch is obsoleted by kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch is obsoleted by kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch is a duplicate with kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch is obsoleted by kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch is obsoleted by kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch kernel-headers-2.6.32-379.5.1.lve1.1.9.6.1.el6.x86_64 is a duplicate with kernel-headers-2.6.32-320.4.1.lve1.1.4.el6.x86_64 keyutils-libs-1.4-4.el6.x86_64 is a duplicate with keyutils-libs-1.4-3.el6.x86_64 krb5-libs-1.9-33.el6_3.3.x86_64 is a duplicate with krb5-libs-1.9-22.el6_2.1.x86_64 libblkid-2.17.2-12.7.el6.x86_64 is a duplicate with libblkid-2.17.2-12.4.el6.x86_64 libcom_err-1.41.12-12.el6.x86_64 is a duplicate with libcom_err-1.41.12-11.el6.x86_64 libgcc-4.4.6-4.el6.x86_64 is a duplicate with libgcc-4.4.6-3.el6.x86_64 libselinux-2.0.94-5.3.el6.x86_64 is a duplicate with libselinux-2.0.94-5.2.el6.x86_64 libstdc++-4.4.6-4.el6.x86_64 is a duplicate with libstdc++-4.4.6-3.el6.x86_64 libtiff-3.9.4-6.el6_3.x86_64 is a duplicate with libtiff-3.9.4-5.el6_2.x86_64 libudev-147-2.42.el6.x86_64 is a duplicate with libudev-147-2.40.el6.x86_64 libuuid-2.17.2-12.7.el6.x86_64 is a duplicate with libuuid-2.17.2-12.4.el6.x86_64 libxml2-2.7.6-8.el6_3.3.x86_64 is a duplicate with libxml2-2.7.6-4.el6_2.4.x86_64 nspr-4.9.1-2.el6_3.x86_64 is a duplicate with nspr-4.8.9-3.el6_2.x86_64 nss-util-3.13.5-1.el6_3.x86_64 is a duplicate with nss-util-3.13.1-3.el6_2.x86_64 openssl-1.0.0-25.el6_3.1.x86_64 is a duplicate with openssl-1.0.0-20.el6_2.5.x86_64 python-2.6.6-29.el6_3.3.x86_64 is a duplicate with python-2.6.6-29.el6.x86_64 python-libs-2.6.6-29.el6_3.3.x86_64 is a duplicate with python-libs-2.6.6-29.el6.x86_64 readline-6.0-4.el6.x86_64 is a duplicate with readline-6.0-3.el6.x86_64 sed-4.2.1-10.el6.x86_64 is a duplicate with sed-4.2.1-7.el6.x86_64 tzdata-2012c-3.el6.noarch is a duplicate with tzdata-2012c-1.el6.noarch xmlrpc-c-1.16.24-1209.1840.el6.x86_64 is a duplicate with xmlrpc-c-1.16.24-1200.1840.el6_1.4.x86_64 xmlrpc-c-client-1.16.24-1209.1840.el6.x86_64 is a duplicate with xmlrpc-c-client-1.16.24-1200.1840.el6_1.4.x86_64 Error: check all Tried: #rm /var/lib/rpm/__db* #rpm --rebuilddb #yum clean all Tried also running yum-complete-transaction still won't finish the update. ls -ld /var/tmp/ drwxrwxrwt. 20 root root 12288 Oct 3 18:44 /var/tmp/ df -h /var/tmp/ Filesystem Size Used Avail Use% Mounted on /tmp 3.9G 1.2G 2.6G 32% /var/tmp Latest errors: Error: Protected multilib versions: libgcc-4.4.6-4.el6.i686 != libgcc-4.4.6-3.el6.x86_64 Error: Protected multilib versions: glibc-2.12-1.80.el6_3.5.i686 != glibc-2.12-1.47.el6_2.12.x86_64 EDITED: yum repolist Loaded plugins: fastestmirror, rhnplugin, security Loading mirror speeds from cached hostfile * cloudlinux-x86_64-server-6: cl.banahosting.com repo id repo name status cloudlinux-x86_64-server-6 CloudLinux Server 6 x86_64 10,948+725 repolist: 10,948 [~]# package-cleanup --dupes Loaded plugins: fastestmirror, rhnplugin xmlrpc-c-client-1.16.24-1209.1840.el6.x86_64 xmlrpc-c-client-1.16.24-1200.1840.el6_1.4.x86_64 bind-libs-9.7.3-8.P3.el6_2.2.x86_64 bind-libs-9.8.2-0.10.rc1.el6_3.3.x86_64 libblkid-2.17.2-12.4.el6.x86_64 libblkid-2.17.2-12.7.el6.x86_64 libtiff-3.9.4-5.el6_2.x86_64 libtiff-3.9.4-6.el6_3.x86_64 audit-libs-2.1.3-3.el6.x86_64 audit-libs-2.2-2.el6.x86_64 libstdc++-4.4.6-3.el6.x86_64 libstdc++-4.4.6-4.el6.x86_64 sed-4.2.1-10.el6.x86_64 sed-4.2.1-7.el6.x86_64 python-libs-2.6.6-29.el6_3.3.x86_64 python-libs-2.6.6-29.el6.x86_64 coreutils-libs-8.4-16.el6.x86_64 coreutils-libs-8.4-19.el6.x86_64 libudev-147-2.40.el6.x86_64 libudev-147-2.42.el6.x86_64 chkconfig-1.3.49.3-2.el6.x86_64 chkconfig-1.3.49.3-1.el6_2.x86_64 keyutils-libs-1.4-4.el6.x86_64 keyutils-libs-1.4-3.el6.x86_64 glibc-2.12-1.47.el6_2.12.x86_64 glibc-2.12-1.80.el6_3.5.x86_64 tzdata-2012c-3.el6.noarch tzdata-2012c-1.el6.noarch coreutils-8.4-19.el6.x86_64 coreutils-8.4-16.el6.x86_64 dbus-libs-1.2.24-7.el6_3.x86_64 dbus-libs-1.2.24-5.el6_1.x86_64 libxml2-2.7.6-4.el6_2.4.x86_64 libxml2-2.7.6-8.el6_3.3.x86_64 abrt-libs-2.0.8-6.el6.x86_64 abrt-libs-2.0.4-14.el6.centos.x86_64 expat-2.0.1-9.1.el6.x86_64 expat-2.0.1-11.el6_2.x86_64 python-2.6.6-29.el6.x86_64 python-2.6.6-29.el6_3.3.x86_64 gtk2-2.18.9-6.el6.centos.x86_64 gtk2-2.18.9-10.el6.x86_64 libcom_err-1.41.12-12.el6.x86_64 libcom_err-1.41.12-11.el6.x86_64 gawk-3.1.7-10.el6.x86_64 gawk-3.1.7-9.el6.x86_64 readline-6.0-4.el6.x86_64 readline-6.0-3.el6.x86_64 glibc-common-2.12-1.80.el6_3.5.x86_64 glibc-common-2.12-1.47.el6_2.12.x86_64 libselinux-2.0.94-5.2.el6.x86_64 libselinux-2.0.94-5.3.el6.x86_64 cups-libs-1.4.2-48.el6_3.1.x86_64 cups-libs-1.4.2-44.el6_2.3.x86_64 nspr-4.9.1-2.el6_3.x86_64 nspr-4.8.9-3.el6_2.x86_64 cagefs-safebin-3.5-1.el6.cloudlinux.x86_64 cagefs-safebin-3.6-6.el6.cloudlinux.x86_64 libuuid-2.17.2-12.4.el6.x86_64 libuuid-2.17.2-12.7.el6.x86_64 xmlrpc-c-1.16.24-1209.1840.el6.x86_64 xmlrpc-c-1.16.24-1200.1840.el6_1.4.x86_64 openssl-1.0.0-20.el6_2.5.x86_64 openssl-1.0.0-25.el6_3.1.x86_64 dhcp-common-4.1.1-25.P1.el6_2.1.x86_64 dhcp-common-4.1.1-31.P1.el6_3.1.x86_64 krb5-libs-1.9-33.el6_3.3.x86_64 krb5-libs-1.9-22.el6_2.1.x86_64 nss-util-3.13.5-1.el6_3.x86_64 nss-util-3.13.1-3.el6_2.x86_64 cloudlinux-release-6-6.2.2.x86_64 cloudlinux-release-6-6.3.0.x86_64 e2fsprogs-libs-1.41.12-11.el6.x86_64 e2fsprogs-libs-1.41.12-12.el6.x86_64 glib2-2.22.5-6.el6.x86_64 glib2-2.22.5-7.el6.x86_64 UPDATE 2 I removed all the dupes and then did update and got this: Updating : sudo-1.7.4p5-13.el6_3.x86_64 79/361 Error in POSTIN scriptlet in rpm package sudo-1.7.4p5-13.el6_3.x86_64 warning: /etc/sudoers created as /etc/sudoers.rpmnew error: error creating temporary file /var/tmp/rpm-tmp.hjTOqJ: Invalid argument error: Couldn't create temporary file for %post(sudo-1.7.4p5-13.el6_3.x86_64): Invalid argument Updating : pcre-7.8-6.el6.x86_64 80/361 Traceback (most recent call last): File "/usr/lib/python2.6/site-packages/yum/rpmtrans.py", line 399, in callback self._instCloseFile( bytes, total, h ) File "/usr/lib/python2.6/site-packages/yum/rpmtrans.py", line 475, in _instCloseFile self.base.history.trans_data_pid_end(pid, state) File "/usr/lib/python2.6/site-packages/yum/history.py", line 858, in trans_data_pid_end """, ('TRUE', self._tid, pid, state)) File "/usr/lib/python2.6/site-packages/yum/sqlutils.py", line 168, in executeSQLQmark return cursor.execute(query, params) sqlite3.OperationalError: unable to open database file error: python callback <bound method RPMTransaction.callback of <yum.rpmtrans.RPMTransaction instance at 0x5c7cfc8>> failed, aborting! - [~]# lsattr /var/tmp/ -------------e- /var/tmp/cache_5b07945563e03aec1c44917886fd99a6 -------------e- /var/tmp/sess_6edfafda1a191f6986bd020ed945eea0 -------------e- /var/tmp/sess_1b837feecdd4c9e6aa6ecd81d41fda75 -------------e- /var/tmp/sess_70bec5f392b4f5f75ac444f5c82db2dc -------------e- /var/tmp/sess_24cd226ba0a370a6d3838a37745b2e15 -------------e- /var/tmp/nginx_proxy -------------e- /var/tmp/sess_19fb1dd060e42c9de8786ef34d7fcf6e -------------e- /var/tmp/sess_b4ac777076c5122a6e27d776de0a2fcb -------------e- /var/tmp/sess_5077441775ef8d07a2185e8fd48a4aa8 -------------e- /var/tmp/cache_4e71d930fe8250e222ae4d1dc39646ff -------------e- /var/tmp/sess_eb6eb29b38b55b85303c3137611f0a2faa15c21d -------------e- /var/tmp/sess_81e7e8d93b395f2c8d7e3fe12cc59e56 -------------e- /var/tmp/sess_05c7f305bdbf9a4c7af251d33ac59766 -------------e- /var/tmp/sess_0ad9369063a37b6b399688a835d69ed2 -------------e- /var/tmp/cache_c780deda617678faeea8f8a34395ac27 -------------e- /var/tmp/sess_9773332e3c99ee18dca0b05e8f02a41e -------------e- /var/tmp/sess_1d9b02b068ea81a3975599ddc12bcfb1 -------------e- /var/tmp/sess_1ffeff444123e924834dc5e80d07571e -------------e- /var/tmp/sess_aa56725471c84d9a06745c56dc499db7 -------------e- /var/tmp/sess_51e19964d7e1a164c63f4c72fa43475c33debbc0 -------------e- /var/tmp/sess_a83c7a05bb189a465b8813ff9e566aa8f9124079 -------------e- /var/tmp/sess_2f506ba5b77c61107871e8cf80393cdb -------------e- /var/tmp/sess_7bfe1578605b259ec5e4fd2200df4cd0 -------------e- /var/tmp/sess_f6e47011789d8d48d56dd78a398d98d5719414a7 -------------e- /var/tmp/sess_b7c43a90a8b8d8f02b0fffca77796ce5 -------------e- /var/tmp/sess_6c3e7103453ad4daba815bd96a903785 -------------e- /var/tmp/sess_86f32a22507d8410b3f0fc7d71a135d5 -------------e- /var/tmp/sess_aaf72d3e8cfb2f27ffdff61323f97e7553855a05 -------------e- /var/tmp/sess_5de4488e2ee03ac0f99ab9494573ccb1 -------------e- /var/tmp/sess_716d97bba4abdb38704a9e4212f6fddc -------------e- /var/tmp/sess_534908a9510a32eda13a5dc95ac022cc -------------e- /var/tmp/sess_626a58203d93427c79621ea4fec0906d -------------e- /var/tmp/sess_827ca92d10d3797f2c187c41764a7036 -------------e- /var/tmp/sess_6282962d77f7bead20e785fbdb9a3d8f -------------e- /var/tmp/cache_b012c8a729fc54a296a700ed92930a0e -------------e- /var/tmp/sess_631e5ba769773da056108d3fbd143963 -------------e- /var/tmp/cache_30bb7f1333ba5f96a229c91a3385d8b5 -------------e- /var/tmp/sess_93e085706b29c3e4e3593bfe39b1079e -------------e- /var/tmp/sess_abd78bd6c285d681c90de8c617747ab3 -------------e- /var/tmp/sess_e144544ed925569018e6607b05f43f253f75e2aa -------------e- /var/tmp/sess_5d3d036c772847a4508d3e100b173d84 -------------e- /var/tmp/sess_f35243d1f40bd8d9ce08940fafc00d93 -------------e- /var/tmp/sess_761c3ffa811b959638ed0b266741eaa4 -------------e- /var/tmp/mm.sem.sNdxjf -------------e- /var/tmp/sess_006d45dbd807291f7bffbd1db3707ed6 -------------e- /var/tmp/cache_2d0162aac9f87c1978ac644923a5e2fe -------------e- /var/tmp/sess_22c534418c380b72d105935b59713dd1 -------------e- /var/tmp/sess_94f72ef408567a15f6287c518e93898e -------------e- /var/tmp/cache_6fe03c83bb87489f3921db1c974dfc0e -------------e- /var/tmp/sess_48bbfa2a2a8793a62c7fd6a389a2763e -------------e- /var/tmp/mm.sem.ERERMV -------------e- /var/tmp/sess_20aba82c03a69b2dc6af66c499c38ee67e27368f -------------e- /var/tmp/sess_f94fe0589a79c934815ef359bcb0a16c7080d937 -------------e- /var/tmp/sess_460390801eb004593b4dee83779f414e -------------e- /var/tmp/spamd-52811-init -------------e- /var/tmp/cache_6427fdb235d59b0b2fbd105bf23d2e87 -------------e- /var/tmp/cache_4ce12d8350d7c0361dc1bf15d552a2d8 -------------e- /var/tmp/sess_039fec2a643340f118b6355e4c836ae8 -------------e- /var/tmp/sess_fa46fa80b26e6cf3d9c7de942d5dbcff -------------e- /var/tmp/cache_664858e614367812148716536e22d030 -------------e- /var/tmp/sess_4c8d4c44fbd828dc17415ce6aa213115 -------------e- /var/tmp/sess_d231a6c0e5dd4d7bacbf9de3d8bb298f -------------e- /var/tmp/sess_a82f8a088a8e37d375f6a9fede4a54d2 -------------e- /var/tmp/sess_604697227ae5359e5783dc9407845338 -------------e- /var/tmp/sess_5b4e623536640abe671b40563d03817d -------------e- /var/tmp/sess_2aba0aff64f3c18f22e0b79d591259e2 -------------e- /var/tmp/sess_bfd52a2d2d80880f8e26ad460739a0494f0d1e9e -------------e- /var/tmp/sess_ba9f3e3a7c7111930d6b801aaa833b46 -------------e- /var/tmp/sess_5cc8c5b620015a465359359a0805fbdd -------------e- /var/tmp/sess_84945c41d604b4653a1bf45d83a1917c -------------e- /var/tmp/sess_5f52569b27430780c07d25cfb8177e5c1ef647f0 -------------e- /var/tmp/sess_45896aef9e77f16be1b3e94b3edb2599 -------------e- /var/tmp/sess_5a67d0ef8f826a2f103b429c8464bdd5f75d6218 -------------e- /var/tmp/sess_1fce98bb32e5b34c79fd5a313de32980 -------------e- /var/tmp/sess_f7ea772ff3fbb1eb2ad8712dd2c49ed8 -------------e- /var/tmp/sess_a9dc16bc5c1eb2768bb2600f0d102fde -------------e- /var/tmp/mm.sem.3zwRTu -------------e- /var/tmp/sess_e2cad140703338a4b8c9254ec6b0a1a2 -------------e- /var/tmp/sess_e7c8e85daf9c5424aecb83e066decf31 -------------e- /var/tmp/sess_800f878fa944370f42e76057e7c033e19520bd41 -------------e- /var/tmp/sess_4fdae64eb18599521ace18679795568b -------------e- /var/tmp/sess_958fb886b97de2e767b059376c4724b5 -------------e- /var/tmp/sess_3c832a31f17744a8bb3c59dde02e561aefbc2e48 -------------e- /var/tmp/sess_6d9d7bf04f34e0d82b101f882196a905 -------------e- /var/tmp/sess_7231c75ae4fad2ca5fbcb6de430a7b13 -------------e- /var/tmp/sess_2eadffa2285def9673ce784395d272d8 -------------e- /var/tmp/cache_2ff353b664d8028df967f807ac18593a -------------e- /var/tmp/sess_4138a267f1f5e3ad93c1d64547c63134ae7c0db3 -------------e- /var/tmp/sess_64cd9fa0d6af8e8041aafffbe3db986a -------------e- /var/tmp/tmpg3ycIG -------------e- /var/tmp/cache_b633ac8283d6de8e39d81160d63fc8cd -------------e- /var/tmp/sess_2cee03cf5eafd3ef55d8efa1b0390436 -------------e- /var/tmp/sess_608066c609e28621f2a29ac04a3a6441 -------------e- /var/tmp/sess_46dfb35cf8266699ba9304e5d8c6869d -------------e- /var/tmp/sess_fb202a0ed54cee8832c5f6e0ca7fc1b3 -------------e- /var/tmp/sess_8fe3c5fd8cdda02855e5f9b5a1ea85a4 -------------e- /var/tmp/sess_941376d5cb51e0ba73f9a27ee259c159 -------------e- /var/tmp/sess_4fa17b1eac1d18341d20d0d8d4991ceb -------------e- /var/tmp/cache_de647c956ca6a1b75744ad194aceaa82 -------------e- /var/tmp/mm.sem.Ugu7Be -------------e- /var/tmp/sess_656e8a50759d5b36b963e7eb85e0bb0d -------------e- /var/tmp/sess_983f77b607bbffa1748d6c49557381e9 -------------e- /var/tmp/sess_632860d092e5e374da522ed2f88e83ce -------------e- /var/tmp/sess_030f900b81cc2a4ad095d53ef3ee0791 -------------e- /var/tmp/yum.log -------------e- /var/tmp/cache_810174993c6a2c0efe2edbe4c39a4a81 -------------e- /var/tmp/sess_29e2c781643434e81d189fc41f47fd34 -------------e- /var/tmp/tmpE12ahd -------------e- /var/tmp/sess_935da512fb077e04610266748b3b77f3 - cat /etc/fstab /tmp as: loop,rw,noexec,nosuid,nodev

  Read the article

• Getting SMB file shares working over a PPTP VPN

  - by Ben Scott

  I'm having issues getting SMB file shares working over a PPTP VPN. The server setup consists of a security device (DrayTek V3300) which passes the PPTP authentication to a SBS2003 server running RRAS. The server is the DC and provides DNS and WINS, the single NIC's name server is set to the NIC's IP (192.168...), and DHCP on the DrayTek sets the server IP as the DNS. If I create a new VPN connection in Win7, leaving everything as default apart from the server, username, password and domain, I can: ping everything by IP address resolve IPs with nslookup using their fully-qualified name, as in nslookup fileserver.mydomain.local ping machines by fully-qualified name, as in ping fileserver.mydomain.local However if I try to access a file share: within Explorer, I get "Windows cannot access ..." with "Error code: 0x80004005 Unspecified Error", using net use z: \\fileserver.mydomain.local\share, I get "System error 53 has occurred. The network path was not found." If I add the machine name to my HOSTS file I can use the file share, which is my last-ditch workaround, but I have a number of VPN users and would rather a solution that doesn't involve me trying to hand-edit system files on computers half a country away. If I set the WINS server explicitly in the connection's IPv4 settings I don't have to use the FQN to ping the machine, but that doesn't change anything else. EDIT: The PC I'm having the issue on is running Win 7 Home Premium. After more testing I actually have two other PCs that work, one W7HP, one XP Home, and another Vista PC that doesn't work (not tested as much as the others), all four on the same internet connection (behind the same router). All of them were tested with a straight-forward, all defaults, new VPN configuration.

  Read the article

• XP machines on Domain not reporting WMI Data in a 2003 Server Environment

  - by Az

  I am running into a very quirky issue and I hope someone out there can help. We use a monitoring program for several networks we oversee that is WMI data dependent for a great deal of it's functionality. The Windows 2000 Professional workstations, as well as the 2003 servers in our network report WMI data fine, the Windows XP professional machines will not let me view them from within the WMI snap in for MMC (they return a Win32: Access Denied) error. I am of course logged in with an account with domain admin privileges on the domain controller when I attempt it. DCOM is enabled in component services, and the remote security option is set to allow as well. If we remove the machine from the domain and rejoin it, some workstations will show up as WMI enabled temporarily and then when I try to access them again later I get the access denied error again out of the blue. Hoping someone out there has had a similar problem or they have advice. I have had this problem with the firewall turned on or off. Thanks for your time! -Az

  Read the article

• Amazon Ec2: Problem In Setting up FTP Server

  - by Muntasir

  after setting up My vsFtp Server ON Ec2 i am facing problem , my client is Filezilla and i am getting this error Response: 230 Login successful. Command: OPTS UTF8 ON Response: 200 Always in UTF8 mode. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" Command: TYPE I Response: 200 Switching to Binary mode. Command: PASV Response: 500 OOPS: invalid pasv_address Command: PORT 10,130,8,44,240,50 Response: 500 OOPS: priv_sock_get_cmd Error: Failed to retrieve directory listing Error: Connection closed by server this is the current setting in my vsftpd.conf #nopriv_user=ftpsecure #async_abor_enable=YES # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # chroot_local_user=YES #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list GNU nano 2.0.6 File: /etc/vsftpd/vsftpd.conf # #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd with two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES pasv_enable=YES pasv_min_port=2345 pasv_max_port=2355 listen_port=1024 pasv_address=ec2-xxxxxxx.compute-1.amazonaws.com pasv_promiscuous=YES Note: i have already open those port in security group i mean listen port, min max if someone shows me how to fix this i will be very greatful thanks

  Read the article

• Launching firefox on remote server causes local firefox to start instead

  - by terdon

  Right, this is strange. I am connecting from my laptop (LMDE) to a remote host (SUSE linux enterprise) using ssh -X. I want to launch a firefox instance running on the remote server so I can have access to webpages on a private network. User@RemoteMachine $ which -a firefox /usr/bin/firefox User@RemoteMachine $ /usr/bin/firefox --version Mozilla Firefox 2.0.0.2, Copyright (c) 1998 - 2007 mozilla.org User@LocalMachine $ which -a firefox /usr/bin/firefox User@LocalMachine $ /usr/bin/firefox --version Mozilla Firefox 14.0.1 Now, if firefox is not running on the local machine, everything goes as expected and executing firefox on the remote machine causes a firefox (v 2.0) window running on the remote machine to show up. However, if firefox is running on the local machine a second window of firefox 14.0.1 running on the local machine appears. I have checked top in both machines. In the 2nd case, a firefox process briefely appears on the remote machine and then disappears when the local version of firefox is launched. My questions are the following: What gives? How/why can firefox connect to its existing instance on the local machine? The remote machine appears to have access to the local machine. It, in fact, appears to have the right to execute programs on my local machine. Am I missing something or is this just weird? Is this not a security risk?

  Read the article

• VsFTPd - pam_mkhomedir

  - by Totor

  I am trying to set up a FTP server that authenticates against an LDAP server. This part is done and works. My server is VsFTPd on Ubuntu Server 11.04. But I have to create the home directories for my LDAP users. I am trying to user the pam_mkhomedir module but it is not working: when I add its line to the /etc/pam.d/vsftpd file, my users can not login anymore to the FTP server. The problem is that I have very few information on what is wrong. VsFTPd just responds 530: login incorrect and I could not find a way to get debug or error messages from pam_mkhomedir. Here are my different configuration files. The /etc/pam.d/vsftpd file: auth required pam_listfile.so item=user sense=deny file=/etc/ftpusers onerr=succeed auth required pam_ldap.so account required pam_ldap.so password required pam_ldap.so session optional pam_mkhomedir.so skel=/home/skel debug The /etc/vsftpd.conf file: listen=YES anonymous_enable=NO local_enable=YES write_enable=YES dirmessage_enable=YES use_localtime=YES xferlog_enable=YES connect_from_port_20=YES pam_service_name=vsftpd rsa_cert_file=/etc/ssl/private/vsftpd.pem guest_enable=YES session_support=YES log_ftp_protocol=YES tcp_wrappers=YES Permissions on /home and /home/skel: root@ftp:/home# ls -al total 16 drwxrwxrwx 4 root root 4096 2011-10-11 21:19 . drwxr-xr-x 21 root root 4096 2011-09-27 13:32 .. drwxrwxrwx 2 root root 4096 2011-10-11 19:34 skel drwxrwxrwx 5 foo foo 4096 2011-10-11 21:11 foo root@ftp:/home# ls -al skel/ total 16 drwxrwxrwx 2 root root 4096 2011-10-11 19:34 . drwxrwxrwx 4 root root 4096 2011-10-11 21:19 .. -rwxrwxrwx 1 root root 3352 2011-10-11 19:34 .bashrc -rwxrwxrwx 1 root root 675 2011-10-11 19:34 .profile Yes, I know, permissions are not properly set but security is not the issue here: I first need to get it to work. So, to recapitulate: without pam_mkhomedir my LDAP users can login, but they cannot do anything because they are in an empty chrooted jail. If I add pam_mkhomedir, they cannot login anymore. If anyone has an idea why, or know how to get more information from logs, I would be very grateful, thanks.

  Read the article

• Snow Leopard doesn't repair permissions, despite showing / saying its fixed them?

  - by Jules

  Sometime ago, I used carbon copy as I was replacing my hard drive in my Mac Mini running Snow Leopard. Afterwards, on my new drive I had some permission problems. I've tried several times running a repair permissions / repair disk from disk util. It shows that there are problems and I think it says its correceted the problems. However the problems remain, what can I do to fix them ? It doesn't seem to cause me any problems, that I can tell EDIT Repairing permissions for “Macintosh HD” Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/Italian.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/Italian.lproj/UIAgent.nib". Permissions differ on "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Classes/jconsole.jar", should be -rw-r--r-- , they are lrwxr-xr-x . Repaired "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Classes/jconsole.jar". User differs on "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Home/lib", should be 95, user is 0. Repaired "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Home/lib". User differs on "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Libraries", should be 95, user is 0. Repaired "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Libraries". Permissions differ on "System/Library/Frameworks/JavaVM.framework/Versions/A/Resources/Deploy.bundle/Contents/Home/lib/security/cacerts", should be -rw-r--r-- , they are lrwxr-xr-x . Repaired "System/Library/Frameworks/JavaVM.framework/Versions/A/Resources/Deploy.bundle/Contents/Home/lib/security/cacerts". Permissions differ on "System/Library/Frameworks/JavaVM.framework/Versions/A/Resources/Deploy.bundle/Contents/Resources/Java/deploy.jar", should be -rw-r--r-- , they are lrwxr-xr-x . Repaired "System/Library/Frameworks/JavaVM.framework/Versions/A/Resources/Deploy.bundle/Contents/Resources/Java/deploy.jar". Permissions differ on "System/Library/Frameworks/JavaVM.framework/Versions/A/Resources/Deploy.bundle/Contents/Resources/Java/libdeploy.jnilib", should be -rwxr-xr-x , they are lrwxr-xr-x . Repaired "System/Library/Frameworks/JavaVM.framework/Versions/A/Resources/Deploy.bundle/Contents/Resources/Java/libdeploy.jnilib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreenLeopard386.app/Contents/Resources/Italian.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreenLeopard386.app/Contents/Resources/Italian.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/zh_TW.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/zh_TW.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/zh_TW.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/zh_TW.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/zh_TW.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/zh_TW.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/zh_CN.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/zh_CN.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/zh_CN.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/zh_CN.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/zh_CN.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/zh_CN.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/ko.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/ko.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/ko.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/ko.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/ko.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/ko.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/Dutch.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/Dutch.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/Dutch.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/Dutch.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/Dutch.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/Dutch.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/Italian.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/Italian.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/Italian.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/Italian.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/Spanish.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/Spanish.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/Spanish.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/Spanish.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/Spanish.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/Spanish.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/French.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/French.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/French.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/French.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/French.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/French.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/German.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/German.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/German.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/German.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/German.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/German.lproj/MainMenu.nib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/Japanese.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/Japanese.lproj/RemoteDesktopMenu.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/Japanese.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/Japanese.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/Japanese.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/Japanese.lproj/MainMenu.nib". Permissions differ on "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Resources/JavaPluginCocoa.bundle/Contents/Resources/Java/deploy.jar", should be -rw-r--r-- , they are lrwxr-xr-x . Repaired "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Resources/JavaPluginCocoa.bundle/Contents/Resources/Java/deploy.jar". Permissions differ on "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Resources/JavaPluginCocoa.bundle/Contents/Resources/Java/libdeploy.jnilib", should be -rwxr-xr-x , they are lrwxr-xr-x . Repaired "System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Resources/JavaPluginCocoa.bundle/Contents/Resources/Java/libdeploy.jnilib". Permissions differ on "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/English.lproj/RemoteDesktopMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/Menu Extras/RemoteDesktop.menu/Contents/Resources/English.lproj/RemoteDesktopMenu.nib". Warning: SUID file "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/MacOS/ARDAgent" has been modified and will not be repaired. Permissions differ on "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/English.lproj/UIAgent.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Support/Remote Desktop Message.app/Contents/Resources/English.lproj/UIAgent.nib". Permissions differ on "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/English.lproj/MainMenu.nib", should be drwxr-xr-x , they are -rwxr-xr-x . Repaired "System/Library/CoreServices/RemoteManagement/AppleVNCServer.bundle/Contents/Support/LockScreen.app/Contents/Resources/English.lproj/MainMenu.nib". Group differs on "private/var/log/kernel.log", should be 80, group is 0. Permissions differ on "private/var/log/kernel.log", should be -rw-r----- , they are -rw-r--r-- . Repaired "private/var/log/kernel.log". Group differs on "private/var/log/secure.log", should be 80, group is 0. Permissions differ on "private/var/log/secure.log", should be -rw-r----- , they are -rw-r--r-- . Repaired "private/var/log/secure.log". Group differs on "private/var/log/system.log", should be 80, group is 0. Permissions differ on "private/var/log/system.log", should be -rw-r----- , they are -rw-r--r-- . Repaired "private/var/log/system.log". Permissions repair complete

  Read the article

• Replacing DropBox with: Amazon S3 + SSL + GPG/TrueCrypt + Mounting on OSX ??

  - by Matt Rogish

  So, right now we're using DropBox to share various data files around between approximately 10 Mac OS X systems. However, we already have an S3 account and everyone on the lowest DropBox plan of $10/mo seems too expensive. We'd like to avoid any kind of local storage (share a disk on a desktop or something) since we're a geographically distributed team). So, I am contemplating something that would allow us to replace DropBox with our own home-grown solution. We are all fairly technical people and/or smart enough to follow some steps, so if it's not as "user friendly" as DropBox we're all comfortable with that. There are plenty of docs out there that have bits and pieces of what I want but some of the tools don't seem to fit the requirements: Transport security via SSL to the bucket Encryption of bucket contents Bi-directional syncing Most of the scripts I can find on the internet use "duplicity" which appears to fail #1 (it doesn't look like duplicity supports SSL to S3 - the docs don't state but the protocol looks plain old http http://www.nongnu.org/duplicity/duplicity.1.html#sect6 ) Many scripts use gpg to encrypt files. This seems like it could work, however I have to make sure that each OSX client is able to use the same key to encrypt and decrypt files (key management is left to me to manage). FTP and other client-based apps don't seem to support this at all. Finally, most of the scripts use one-way replication, e.g. using Amazon S3 as a simple backup store. As we'd be using Amazon S3 as the "repository" they fail this one. Whew. So, I'd love a single tool that does this but after an exhaustive search I don't think one exists. In my mind, the magical tool would be some combination of TrueCrypt and rsync. I'd be happy just knowing which tools out there can fulfill my 3 requirements, after that I can stitch together the rest. Any thoughts? THANKS!

  Read the article

• Ubuntu 12.04 LDAP SSL self-signed cert not accepted

  - by MaddHacker

  I'm working with Ubuntu 12.04, using OpenLDAP server. I've followed the instructions on the Ubuntu help pages and can happily connect without security. To test my connection, I'm using ldapsearch the command looks like: ldapsearch -xv -H ldap://ldap.[my host].local -b dc=[my domain],dc=local -d8 -ZZ I've also used: ldapsearch -xv -H ldaps://ldap.[my host].local -b dc=[my domain],dc=local -d8 As far as I can tell, I've setup my certificate correctly, but no matter why I try, I can't seem to get ldapsearch to accept my self-signed certificate. So far, I've tried: Updating my /etc/ldap/ldap.conf file to look like: BASE dc=[my domain],dc=local URI ldaps://ldap.[my host].local TLS_CACERT /etc/ssl/certs/cacert.crt TLS_REQCERT allow Updating my /etc/ldap.conf file to look like: base dc=[my domain],dc=local uri ldapi:///ldap.[my host].local uri ldaps:///ldap.[my host].local ldap_version 3 ssl start_tls ssl on tls_checkpeer no TLS_REQCERT allow Updating my /etc/default/slapd to include: SLAPD_SERVICES="ldap:/// ldapi:/// ldaps:///" Several hours of Googling, most of which resulted in adding the TLS_REQCERT allow The exact error I'm seeing is: ldap_initialize( ldap://ldap.[my host].local ) request done: ld 0x20038710 msgid 1 TLS certificate verification: Error, self signed certificate in certificate chain TLS: can't connect. ldap_start_tls: Connect error (-11) additional info: error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate verify failed After several hours of this, I was hoping someone else has seen this issue, and/or knows how to fix it. Please do let me know if I should add more information, or if you need further data.

  Read the article

• Mounting a TrueCrypt volume over FTP

  - by Maxim Zaslavsky

  Is it possible to mount a TrueCrypt volume file over FTP? Here's how TrueCrypt works with a local file: User inputs path to volume file, enters password TrueCrypt verifies that the password is correct (probably by decrypting the very first part of the volume file?) TrueCrypt reads the directory listing from the volume file and mounts the volume. However, in this step, TrueCrypt does NOT process the whole volume file. The user browses the directory listing and opens a file. TrueCrypt reads only the part of the volume file that contains the file the user wants, and then decrypts it. Once again, TrueCrypt doesn't process the whole volume file - it only reads part of it. The user edits part of the file and saves it. TrueCrypt encrypts the change and edits the volume file. I'm pretty sure it should be possible to mount a volume over FTP, without undermining security and without having to transfer the whole volume file just to read one small part of the volume. Here's how I imagine it: User inputs FTP path to volume file, enters FTP login information, enters password to volume TrueCrypt downloads the very first part of the volume file and verifies that the password is correct TrueCrypt downloads the part of the volume file that contains the directory listing - the data is sent encrypted over FTP and is decrypted locally. The user browses the directory listing and opens a file. TrueCrypt downloads only the part of the volume file that contains the file the user wants, and then decrypts it locally. The user edits part of the file and saves it. TrueCrypt encrypts the change and edits the volume file over FTP, transferring encrypted data only. Is such a feature available?

  Read the article

• Override <customErrors mode="Off"/> message from .NET Framework even when in web.config detailed err

  - by GrZeCh

  Hello, is this possible to override .NET Framework error: Server Error in '/' Application. Runtime Error Description: An application error occurred on the server. The current custom error settings for this application prevent the details of the application error from being viewed remotely (for security reasons). It could, however, be viewed by browsers running on the local server machine. ... <!-- Web.Config Configuration File --> <configuration> <system.web> <customErrors mode="Off"/> </system.web> </configuration> even if web.config (IIS7.5) is set to <httpErrors errorMode="Detailed"/> ? I'm asking because my default setting for IIS7 is <deployment retail="true" /> so no error is being showed and only adding additional error handling module to website will allow to see errors generated by this application and thats why I want to override this message to inform users about it. Any ideas? Thanks

  Read the article

• Subversion Apache Ubuntu - Remote Access?

  - by Hollowsteps

  Okay, a couple days ago I built a bare bones kit into a machine. I've been running through tutorials to get it to work and right now I've gotten as far as making it available in my lan, hooray! However, I cannot access the repositories remotely. Any machine on the lan can easily access it through the hostname or, using 'outbound ip/hostname' or 'outbound ip/machine ip'. The machine can be pinged from a remote, non-lan machine and responds. I just can't get anyone into it outside of my lan. I've been trying to figure it out but I'm lost. I'm breaking a few rules and if any of these would be my problem, please indicate. I don't think I have a static IP (However I check my outbound IP whenever I do testing, is that not enough? It has stayed the same for 5+ days) I have not discussed this set-up with my service provider (Does Optimum Online block port 80? If so, can I just switch apache to listen on a different port?) I am in the DMZ of my router. This is what allowed it to be pinged remotely. For security reasons the machine that is in that zone is turned off most of the time until I can get it locked down. Any help would be appreciated, even if it's just a couple of words I could google to understand what I'm doing wrong. Tortoise SVN does not allow access remotely, but it does within the LAN as well.

  Read the article

• nginx reload failing: `object version does not match bootstrap parameter`

  - by Jean Jordaan

  I added a server stanza to my virtual.conf, and now nginx seems to have a problem reloading the config. At this point I don't know what exactly is going wrong or how to debug better. Any help would be most appreciated. The config test succeeds: root@server:~# service nginx configtest nginx: the configuration file /etc/nginx/nginx.conf syntax is ok nginx: configuration file /etc/nginx/nginx.conf test is successful I'm tailing the logfile. Upon reload, the following error is logged. As far as I can see, the new config is not used. root@server:~# service nginx reload Reloading nginx: [ OK ] root@server:~# ==> /var/log/nginx/error.log <== nginx object version 0.8.54 does not match bootstrap parameter 1.0.15 at /usr/lib64/perl5/XSLoader.pm line 94. Compilation failed in require. BEGIN failed--compilation aborted. 2012/10/18 12:31:07 [alert] 9620#0: perl_parse() failed: 2 This is the version of nginx I'm running: root@server:~# yum info nginx Loaded plugins: fastestmirror, presto Loading mirror speeds from cached hostfile * base: ftp.udc.es * epel: mirror.nl.leaseweb.net * extras: ftp.udc.es * updates: ftp.cica.es Installed Packages Name : nginx Arch : x86_64 Version : 1.0.15 Release : 2.el6 [...] Server OS: CentOS release 6.3 (Final)

  Read the article

• Explain why folder's permissions differ depending on HOW user is accessing server AFP vs SSH

  - by Meltemi

  Hoping someone can explain what is probably fairly obvious...but confuses me. Imagine two users with admin privileges on our server (Mac OS X Server 10.5). Call them joe & bob. both users are members of these groups: Staff Group ID: 20 Workgroup Group ID: 1025 Shared folder "devfolder" has sharing set as so: POSIX: Owner: joe read & write Group: admin read & write Other no access ACL: Workgroup Allow Read & write Question is why when looking at same folder does the ownership appear to change depending on who's doing the looking?!? Both looking at same folder on the server: From Joe's perspective: xserve:devfolder joe$ ls -l drwxrwxr-x 6 joe workgroup 204 May 20 19:32 app drwxrwxr-x 9 joe workgroup 306 May 20 19:32 config drwxrwxr-x 3 joe workgroup 102 May 20 19:32 db drwxrwxr-x 3 joe workgroup 102 May 20 19:32 doc drwxrwxr-x 3 joe workgroup 102 May 20 19:32 lib And from Bob's perspective (folder mounted on his machine via AFP): bobmac:devfolder bob$ ls -l drwxrwxr-x 6 bob _bob 264 May 20 19:32 app drwxrwxr-x 9 bob _bob 264 May 20 19:32 config drwxrwxr-x 3 bob _bob 264 May 20 19:32 db drwxrwxr-x 3 bob _bob 264 May 20 19:32 doc drwxrwxr-x 3 bob _bob 264 May 20 19:32 lib Now if Bob connects to server via SSH then his output is identical to Joe's, as expected. Can anyone tell me what the client is doing in this case and what should be expected when bob creates or updates files in this folder? What tools do I have to better understand this from the command line? Is this normal? Perhaps a "cleaner" way that wouldn't be confusing with "bob _bob"?!?

  Read the article

• Can't delete C:\Config.Msi\75ce84f.rbf

  - by Hugh Allen

  I can't delete C:\Config.Msi\75ce84f.rbf It's not causing any problems but it's a mystery I'd like to solve, preferably before the next reboot because it's scheduled for deletion then (see pendmoves). it's not readonly, system or hidden it's not in use by another process (according to Process Explorer) the NT security permissions aren't the problem either - I am the owner and have Full Control ; as a double-check, the Effective Permissions tab shows that I have permission to delete. Yet trying to delete the file gives "Access is Denied" from both Explorer and cmd. I can however rename it or move it to another folder on the same drive. I can also read it and Virustotal says it's clean which is what I would expect (it's just a Windows Installer temp file - a copy of some DLL I think). The relevant line from Process Monitor is: 6:52:14.3726983 PM 112 Explorer.EXE SetDispositionInformationFile C:\Config.Msi\75ce84f.rbf CANNOT DELETE Delete: True Write 1232 Background: I'm using XP SP2. I recently repaired my Adobe Reader installation to make it the default browser plugin again instead of Foxit. (there seems to be no UI to do it otherwise?) So the installer did its thing and then asked to reboot. As is my habit when rebooting is inconvenient I declined the offer and ran pendmoves to find out what files the installer had scheduled to move / delete. It wanted to delete two files with .rbf extension (rollback files) located in C:\Config.msi\. (this applies to both even though I've been speaking about one). So I tried to delete them manually and couldn't. Does anyone have any ideas what could be preventing deletion? (and I don't think it's malware even though I'm not running AV at the moment)

  Read the article

• Confusion about Kerberos, delegation and SPNs.

  - by Vilx-

  I already posted this question on SO, but the nature of it is between programming and server configuration, so I'll re-post it here as well. I'm trying to write a proof-of-concept application that performs Kerberos delegation. I've written all the code, and it seems to working (I'm authenticating fine), but the resulting security context doesn't have the ISC_REQ_DELEGATE flag set. So I'm thinking that maybe one of the endpoints (client or server) is forbidden to delegate. However I'm not authenticating against an SPN. Just one domain user against another domain user. As the SPN for InitializeSecurityContext() I'm passing "[email protected]" (which is the user account under which the server application is running). As I understand, domain users have delegation enabled by default. Anyway, I asked the admin to check, and the "account is sensitive and cannot be delegated" checkbox is off. I know that if my server was running as a NETWORK SERVICE and I used an SPN to connect to it, then I'd need the computer account in AD to have the "Trust computer for delegation" checkbox checked (off by default), but... this is not the case, right? Or is it? Also - when the checkbox in the computer account is set, do the changes take place immediately, or must I reboot the server PC or wait for a while?

  Read the article

• Set JENKINS_HOME in Tomcat7?

  - by C. Ross

  I'm trying to set up Jenkins in Tomcat7 on Ubuntu. I installed Tomcat7 and deployed jenkins.war, and I now see the Jenkins home page at http://myhost:8080/jenkins, but it's attempting to create the Jenkins directory at /usr/share/tomcat7/.jenkins, which it can't for security reasons. I've already created /srv/jenkins and given the tomcat7 group permissions, and want to set JENKINS_HOME to that path. I've tried adding it to the tomcat configuration in /etc/tomcat7/server.xml: <GlobalNamingResources> <Environment name="JENKINS_HOME" value="/srv/jenkins" type="java.lang.String" override="false"/> <!-- Default settings --> And I've also tried adding it to the automatically created context file in ROOT/META-INF/context.xml (there is no $CATALINA_HOME/conf as far as I can tell). <Context path="/" antiResourceLocking="false" > <Environment name="JENKINS_HOME" value="/srv/jenkins/" type="java.lang.String"/> </Context> But even after restarting tomcat7 I still get the same result (trying to use /usr/share/tomcat7/.jenkins). Where do I need to set the environment variable for JENKINS_HOME in Tomcat7?

  Read the article

• How to get remote firewall administration working with Windows Server Core 2008 R2?

  - by Daniel15

  I'm setting up a Windows Server Core 2008 R2 installation in a VMware virtual machine before setting it up on a live VPS. I've gotten remote administration via MMC working on my computer (a PC running Windows 7) for things like event logs, but I can't seem to get the firewall administration working. No matter what I do, I get the following error mesage: You do not have the correct permissions to open the Windows Firewall with Advanced Security console. You must be a member of the Administrators group or the Network Operators group to perform this task. For more information, contact you system administrator. Error code: 0x5. I've used cmdkey to add valid server credentials on my computer, and enabled remote management with the following commands: netsh advfirewall firewall set rule group="remote administration" new enable=yes netsh advfirewall firewall set rule group="windows firewall remote management" new enable=yes netsh advfirewall set currentprofile settings remotemanagement enable I am not running on a domain (just a workgroup), this is the only Windows Server 2008 computer I have. I've tried turning off the firewall completely, but remote administration is still failing How do I debug this issue? Does anyone know how to fix it? I found a few forum topics about it (eg. Remotely managing Windows Firewall on Server Core gives access denied (error 0x5) on Windows Server TechCenter) but they didn't help (I've already tried most of the fixes listed).

  Read the article

• Weird "missing" CD/DVD driver during Windows Server 2008 installation

  - by Django Reinhardt

  Hi. We have an old PowerEdge 860 that we're trying to install Windows Server 2008 R2 onto. At present the machine doesn't have any OS installed, so we're doing a clean install from a DVD. Pretty simple stuff. The problem is that, although the installation process starts off well (asking for language and locale settings), as soon as we click "Install Now" we're told "A required CD/DVD device driver is missing." The operating system has already booted from our only DVD drive(!). I've seen other people complain about this problem (usually in relation to installing Vista or Windows 7) but I've not found a 100% solution yet. (Our DVD drive is a Hitachi LG GWA-4400N, salvaged from an old laptop. There have never been any drivers released for this device, nor any firmware updates.) The most promising lead I have is from someone claiming that Windows is actually asking for a driver for the ATAPI/IDE Controller here. UPDATE See my answer below... It was most likely a corrupt download. (*shame*) I will update this question when I know for sure.

  Read the article

• TS (RD) Gateway Authentication Problem "The logon attempt failed"

  - by user2059

  I've been using TS Gateway to permit remote access for our staff for a few months now, and all has been well. Users either connect to a traditional terminal server desktop or hit our website and start an TS RemoteApp application- in both cases the connection is routed through a TS Gateway. However I came into work this morning to find that has stopped authenticating users through TS Gateway, each time returning "The logon attempt failed" as seen in the image even though the credentials are correct. It should be noted that everything works fine if the Gateway is taken out of the equation, it's the TS Gateway component that is causing these problems. Users experience this problem whether they connect through XP SP3, Vista or 7. On the server a total of 4 entries appear in the Windows security log at exactly the same time for each failed logon attempt: two 4624 "An account was successfully logged on" messages for the user, immediately followed by two 4634 "An account was logged off"s. This suggests that the server is accepting the credentials as correct, then booting the user off. Nothing at all is recorded in the NPS and Terminal Server logs. A reboot doesn't change things. Neither does completely removing and reinstalling the NPS and Terminal Server roles. I'm baffled as to how this can happen suddenly without warning. Any suggestions would be greatly appreciated.

  Read the article

< Previous Page | 588 589 590 591 592 593 594 595 596 597 598 599  | Next Page >