Search Results

Search found 16987 results on 680 pages for 'second'.

Page 595/680 | < Previous Page | 591 592 593 594 595 596 597 598 599 600 601 602  | Next Page >

  • Share the same subnet between Internal network and VPN Clients

    - by Pascal
    I would like to set up a configuration where VPN clients connecting to my Forefront TMG can access all the resources of my Internal network without having the to use the option "Use default gateway on remote network" on the VPN's TCP/IP Ipv4 Advanced Settings. This is important to me, since they can use their own internet while accessing my network through VPN (the security implications of this are acceptable on my cenario) My Internal network runs on 10.50.75.x, and I set up Forefront TMG to relay the DHCP of my Internal network to the VPN clients, so they get IPs from the same range as the Internal network. This setup initially works, and the VPN clients use their own internet, and can access anything that is on the internal network. However, after a while, HTTP Proxy Traffic from the Internal network starts getting routed to the IP of the RRAS Dial In Interface, instead of the IP of the Internal's network gateway. When this happens, the HTTP Proxy starts getting denied for obvious reasons. My first question is: does this happen because Forefront TMG wasn't designed to handle a cenario that I described above, and it "loses itself"? My second question is: Is there any way to solve this problem, either through configuration or firewall policies? My third question is: If there's no way that it can work with the cenario above, is there another cenario that will solve my problem, and do what I'd like it to do properly? Below are my network routes: 1 => Local Host Access => Route => Local Host => All Networks 2 => VPN Clients to Internal Network => Route => VPN Clients => Internal 3 => Internet Access => NAT => Internal, Perimeter, VPN Clients => External 4 => Internal to Perimeter => Route => Internal, VPN Clients => Perimeter Tks!

    Read the article

  • Can only bring up one of two interfaces

    - by mstaessen
    I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

    Read the article

  • joining text files with 600M+ lines

    - by dnkb
    I have two files huge.txt and small.txt. Huge has around 600M rows and it's 14Gigs, each line has four space separated words (tokens) and finally another space separated column with a number. Small has 150K rows with a size of ~3M, a space separated word and a number. Both Files are sorted using the sort command, with no extra options. The words in both files may include apostrophes (') and dashes (-). The deisred output would contain all columns from the huge.txt and the second column (the number) from small txt where the first word of huge.txt and the first word of small.txt match. My attemtpts below failed miserably with the following error: cat huge.txt|join -o 1.1 1.2 1.3 1.4 2.2 - small.txt > output.txt join: memory exhausted What I suspect is that the sorting order isn't right somehow even though the files are pre-sorted using: sort -k1 huge.unsorted.txt > huge.txt sort -k1 small.unsorted.txt > small.txt Problems seem to appear around words that have apostrophes (') or dashes (-). I also tried dictinoary sorting using the -d option bumping into the same error at the end. I see two ways out of this but don't know how to implement any of them. 1) Any tips how to sort the files in a way that the join command considers them to be sorted properly? 2) I was thinking of calculating MD5 or some other hashes of the strings to get rid of the apostrophes and dashes, and do the sorting and joining with the hashes instead of the strings themselves an dat the "translate" back the hashes to strings, but leave the numbers intact at the end of the lines. Since there would be only 150K hashes it's not that bad. What would be a good way to calculate individual hashes for each of the strings? Some AWK magic? See file samples at the end. Thank you! sample of huge.txt had stirred me to 46 had stirred my corruption 57 had stirred old emotions 55 had stirred something in 69 had stirred something within 40 sample of small.txt caley 114881 calf 2757974 calfed 137861 calfee 71143 calflora 154624 calfskin 148347 calgary 9416465 calgon's 94846

    Read the article

  • How to use AD/GPO/Print Services to "push out" a new printer driver to replace a broken one? How did my server get a broken driver?

    - by Zac B
    Context: We have an AD/GPO-managed corporate network with a little over a hundred PCs running Windows 7 x64, and a few managed printers. Our Server2008R2 primary domain controller is configured as a print server for them all. Problem: After a recent windows update and restart (no printer driver updates were included) on the DC, a particular shared printer (Lexmark T650) has begin exhibiting some strange behavior. First, it prints a preceding and following blank page for almost every document, on jobs submitted by about half of client machines (no separator page is configured on the server or any of the clients I've seen). Second, whenever someone tries to access "Printing Preferences" on any client, they recieve the following error message (this happens everywhere, 100% of the time, and didn't happen before the update on the DC): Once they click "OK", the prefs screen appears (with no separator page selected) and everything seems fine. I'm not even sure if these two issues are related, but everyone seems affected by one or both of those issues. What I've Tried: I've been hesitant to un-deploy the problem printer, or remove it via GPO, as it's pretty heavily used. I've tried updating (via MS update and our internal WSUS server) client machines and the DC. No printer driver updates have appeared, and no number of updates or restarts on the server or the client seems to have achieved anything other than my boss getting grumpy that I'm bouncing the domain controller so often. I've tried deleting the drivers on the server, and re-installing them from the original source that has worked for the past year...no change. I've tried selecting "New Driver" for one of the shared printers on a client machine, running as domain admin, and pushed the latest driver found by MSupdate back up to the DC. This changed the version number of the driver recorded in the print server manager, but caused no change--on the client I pushed from, or on any other. The error still appears. Question: Why the heck is this happening? Obviously, I got a bad driver from somewhere, but how do I get rid of it? I don't know of any "roll back drivers" functionality for centrally managed print drivers like Windows offers for other devices. How would I a) get this issue resolved on a client, and b) push the fix to the other members of the domain?

    Read the article

  • Nginx - basic http authentication on PHP-script

    - by half_bit
    I added a PHP-Script that serves as "cgi-bin", Configuration: location ~^/cgi-bin/.*\.(cgi|pl|py|rb) { gzip off; fastcgi_pass 127.0.0.1:9000; fastcgi_index cgi-bin.php; fastcgi_param SCRIPT_FILENAME /etc/nginx/cgi-bin.php; fastcgi_param SCRIPT_NAME /cgi-bin/cgi-bin.php; fastcgi_param X_SCRIPT_FILENAME /usr/lib/$fastcgi_script_name; fastcgi_param X_SCRIPT_NAME $fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; fastcgi_param REMOTE_USER $remote_user; } PHP-Script: <?php $descriptorspec = array( 0 => array("pipe", "r"), // stdin is a pipe that the child will read from 1 => array("pipe", "w"), // stdout is a pipe that the child will write to 2 => array("pipe", "w") // stderr is a file to write to ); $newenv = $_SERVER; $newenv["SCRIPT_FILENAME"] = $_SERVER["X_SCRIPT_FILENAME"]; $newenv["SCRIPT_NAME"] = $_SERVER["X_SCRIPT_NAME"]; if (is_executable($_SERVER["X_SCRIPT_FILENAME"])) { $process = proc_open($_SERVER["X_SCRIPT_FILENAME"], $descriptorspec, $pipes, NULL, $newenv); if (is_resource($process)) { fclose($pipes[0]); $head = fgets($pipes[1]); while (strcmp($head, "\n")) { header($head); $head = fgets($pipes[1]); } fpassthru($pipes[1]); fclose($pipes[1]); fclose($pipes[2]); $return_value = proc_close($process); } else { header("Status: 500 Internal Server Error"); echo("Internal Server Error"); } } else { header("Status: 404 Page Not Found"); echo("Page Not Found"); } ?> The problem with it thought is that I cannot add basic authentication. As soon as I enable it for location ~/cgi-bin it gives me a 404 error when I try to look it up. How can I solve this? I thought about restricting access to only my second server where I then add basic authentication over a proxy, but there must be a simpler solution. Sorry for the bad title, I couldn't think of a better one.

    Read the article

  • Can I use one virtualbox disk for multiple machines?

    - by mxp
    I'm not sure what search term to use and skimming through the VirtualBox manual didn't help me either, so I ask my two questions here... My setup is this: PC with dual boot into Windows 7 and a Debian operating system (both 64bit). I've created a virtual machine (Kubuntu, 64bit) under Windows and put it's VDI file on a SMB share of my NAS. Then I created a VM under linux using the same settings for memory etc and assigned the existing VDI file to it. My idea was that I could use that virtual machine from Windows and Linux as well. (1) Is this generally something that should work without problems? I noticed that snapshots get me into trouble because they appear to be not visible from the other operating system: The snapshots I took after installing the guest system are not visible under Linux. That's why I shut down the VM after usage and not save its state while it's running. My current problem is this: I have used the VM under Windows first, then under Linux. Now it will only start on Linux. When trying this on Windows the guest OS detects some kind of hard disk error and fails to boot because it cannot mount its drive. Obviously the virtual hard disk won't fail so it must have something to do with me using it under Linux. (2) How can I fix that? Update: It also looks like any changes I made in the VM under Linux have been reset by trying to boot it under Windows. Looks like it's back to the latest snapshot. I'm confused... Update The answer to my first question can be found below. In short: It works, as long as you don't use snapshots. The answer to my second question is this: Under Windows set the VM back to the latest snapshot and then discard the snapshot so it gets merged. There should be no snapshots left at the end. If you have multiple snapshots, discard the earliest ones first (Snapshot 1, then 2, 3, ...). I'm not sure what happens if you start at the end (.., 3, 2, 1). This of course leads to some data loss since you revert all changes since the last snapshot. But at least the VM is usable again.

    Read the article

  • cd Command Linux and Mystery Flags

    - by Jason R. Mick
    Platform: CentOS 6.2 Shell:tcsh I'm playing around with cd for a BASH script, and noticed the wondrous cd - option, but was left with many questions... Why the cd -? Isn't this redundant with cd ..? EDIT [As FatalError points out, these two commands don't do the same things... so the answer is "no"] Can you delve farther back into your history with - flag, a la in a browser? e.g. When I type cd -, it takes me to my previous directory, but then if I enter that command again, it takes me to the directory I just came from, creating a sort of loop. Is a shorthand for going back multiple levels supported?EDITI realize I can go back with cd .., but was hoping this could be a gateway to a less verbose deep back, e.g. cd -3 vs. cd ../../../ ... hopefully that clarifies what I'm asking....EDIT2As to the current feedback, while .. is a special directory, I don't see a reason why the built-in cd to the terminal couldn't use a shorthand for ../../ ... ../ e.g. cd ..5 or why the built-in also couldn't have a history (a la auto pushd/popd) that could be turned on and used like cd -3. I get that this could be somewhat of security/privacy risk, but I don't see how it's any worst than storing a command history, which most shells/terminals do. The manpage for cd, accessible via man cd and help cd (it's the same for either command), only lists -L and -P flags. However when I type in cd --help it outputs Usage: cd [-plvn][-|<dir>].. Am I right in assuming the other flags and the - (back) option are nonstandard? What are the -n and -v flags for? Both seem to take me back to my home directory, that's all I've been able to figure out via experimentation. A quick read on web resources [1][2] offered just the same sort of info that the man page did and didn't answer my questions. Note: The second Linux-centric resource above claimed cd only had two options (obviously not true in current CentOS) hence my assumption that this functionality could be non-standard.

    Read the article

  • MongoDB and datasets that don't fit in RAM no matter how hard you shove

    - by sysadmin1138
    This is very system dependent, but chances are near certain we'll scale past some arbitrary cliff and get into Real Trouble. I'm curious what kind of rules-of-thumb exist for a good RAM to Disk-space ratio. We're planning our next round of systems, and need to make some choices regarding RAM, SSDs, and how much of each the new nodes will get. But now for some performance details! During normal workflow of a single project-run, MongoDB is hit with a very high percentage of writes (70-80%). Once the second stage of the processing pipeline hits, it's extremely high read as it needs to deduplicate records identified in the first half of processing. This is the workflow for which "keep your working set in RAM" is made for, and we're designing around that assumption. The entire dataset is continually hit with random queries from end-user derived sources; though the frequency is irregular, the size is usually pretty small (groups of 10 documents). Since this is user-facing, the replies need to be under the "bored-now" threshold of 3 seconds. This access pattern is much less likely to be in cache, so will be very likely to incur disk hits. A secondary processing workflow is high read of previous processing runs that may be days, weeks, or even months old, and is run infrequently but still needs to be zippy. Up to 100% of the documents in the previous processing run will be accessed. No amount of cache-warming can help with this, I suspect. Finished document sizes vary widely, but the median size is about 8K. The high-read portion of the normal project processing strongly suggests the use of Replicas to help distribute the Read traffic. I have read elsewhere that a 1:10 RAM-GB to HD-GB is a good rule-of-thumb for slow disks, As we are seriously considering using much faster SSDs, I'd like to know if there is a similar rule of thumb for fast disks. I know we're using Mongo in a way where cache-everything really isn't going to fly, which is why I'm looking at ways to engineer a system that can survive such usage. The entire dataset will likely be most of a TB within half a year and keep growing.

    Read the article

  • NGINX rewrite rules help. Redirect not working and want to get rid of index.php in urls

    - by Tamerax
    hey! I have 2 questions for nginx users. 1) I'm trying to setup my joomla server onto my new linode running NGINX and after much (like days) of searching and testing, I finally have a config that works with with SEF url plugins...sorta. I was using an apache system on the old server and it used mod_rewrite and life was fine in terms of SEF. Since NGINX doesn't have mod_rewrite, I found something that works BUT it constantly leaves index.php in the urls. ex: http://mysite.com/index.php/forum i want it to be just http://mysite.com/forum but without mod_rewrite it doesn't seem to be possible in joomla that i'm aware of. I know in wordpress it IS possible but I have to use a plugin. Here is my config file: server { listen 80; server_name mysite.com www.mysite.com; access_log /home/public_html/mysite.com/log/access.log; error_log /home/public_html/mysite.com/log/error.log; root /home/public_html/mysite.com/public/; large_client_header_buffers 4 8k; # prevent some 400 errors index index.php index.html; fastcgi_index index.php; location / { expires 30d; error_page 404 = @joomla; log_not_found off; } # Rewrite location @joomla { rewrite ^(.*)$ /index.php?q=last; } # Static Files location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico)$ { access_log off; expires 30d; } # PHP location ~ \.php { keepalive_timeout 0; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include /usr/local/nginx/conf/fastcgi_params; fastcgi_param SCRIPT_FILENAME /home/public_html/mysite.com/public /$fastcgi_script_name; } } 2) second question should be easy but i can't get it to work. I want to use the same config I posted above and have either mysite.com or www.mysite.com both forward to mysite.com/portal. Basically when you hit up the front page with or without the www, it all gets forwarded to a sub directory on the server I called Portal. I have tried several variations of: rewrite ^/(.*) http://www.example.com/portal/$1 permanent; but it usually ends with firefox telling me there is some crazy loop happening the address bar saying something like mysite.com/portalportalportalportalportal.........on and on. So, any help on either of these issues would be awesome!! Thanks!!

    Read the article

  • IT merger - self-sufficient site with domain controller VS thin clients outpost with access to termi

    - by imagodei
    SITUATION: A larger company acquires a smaller one. IT infrastructure has to be merged. There are no immediate plans to change the current size or role of the smaller company - the offices and production remain. It has a Win 2003 SBS domain server, Win 2000 file server, linux server for SVN and internal Wikipedia, 2 or 3 production machines, LTO backup solution. The servers are approx. 5 years old. Cisco network equippment (switches, wireless, ASA). Mail solution is a hosted Exchange. There are approx. 35 desktops and laptops in the company. IT infrastructure unification: There are 2 IT merging proposals. 1.) Replacing old servers, installing Win Server 2008 domain controller, and setting up either subdomain or domain trust to a larger company. File server and other servers remain local and synchronization should be set up to a centralized location in larger company. Similary with the backup - it remains local and if needed it should be replicated to a centralized location. Licensing is managed by smaller company. 2.) All servers are moved to a centralized location in larger company. As many desktop machines as possible are replaced by thin clients. The actual machines are virtualized and hosted by Terminal server at the same central location. Citrix solutions will be used. Only router and site-2-site VPN connection remain at the smaller company. Backup internet line to insure near 100% availability is needed. Licensing is mainly managed by larger company. Only specialized software for PCs that will not be virtualized is managed by smaller company. I'd like to ask you to discuss both solutions a bit. In your opinion, which is better from the operational point of view? Which is more reliable, cheaper in the long run? Easier to manage from the system administrator's point of view? Easier on the budget and easier to maintain from IT department's point of view? Does anybody have any experience with the second option and how does it perform in production environment? Pros and cons of both? Your input will be of great significance to me. Thank you very much!

    Read the article

  • Strange monitor issue - screen goes black after a few seconds

    - by Scott Szretter
    My LCD monitor display is going black (turning off). It's a Samsung SYncMaster 2233 widescreen. I am trying to figure out if there is anything I can do about it, or if the monitor is junk. I have tried multiple computers, all have the same issue. I have tried a different vga cable, same issue. Power and video cables are tight / double checked. When I power on the monitor, the blue light turns on at the bottom. Then a second or two later the video comes up as expected and it looks fine. However, about 2-3 seconds after that, the screen goes black. The blue light is still on and solid at the bottom (blue light normally flashes when the monitor is sleeping). If I power cycle the monitor, same thing happens. With no computer connected or when I unplug the vga cable, I see the searching for signal message "digital", then the screen goes black. However it usually shows "digital" then "analog" after that and switches between the two a few times. The buttons on the side do not do anything, although they may be, I just can not see if they are or not. I can usually get the "digital" message by pressing the buttons on the side, but then it quickly goes black again. What is really strange is sometimes I can get it to work fine. I am not sure what the difference is. Last week I connected it up and it worked fine and it stayed fine for at least a week! I did not turn it off or anything, I just let the OS put the display to sleep. Then this week one morning I started having the screen going black issue again. Seems like something is either loose inside or beginning to fail. Do you think there is any hope for it? update: pushing the input select button causes the "digital" and "analog" messages to flash on the screen, but only for a few seconds then it goes black. When it was working properly, those messages would flash back and fourth for probably 10-20 seconds then a message would show saying check input signal, but now just a black screen.

    Read the article

  • RDP exits immediately after connecting to Windows Server 2008 R2

    - by carpat
    Background: I recently got a Windows cloud VPS server. I don't have much experience with server admin (I'm a programmer), and what little I do have is with linux servers. Ever since getting the server I've been having issues with RDP. I can connect about two or three times, after which point I can't connect until one of the tech guys "fixes" it (see below). When I connect, I can stay connected for hours with no problem. When the problem connecting starts, the first time I try to log in, the remote desktop window pops up, starts connecting, and then exits with "Your Remote Desktop session has ended". After that, for about 10-20 minutes if I try to connect again, the connections times out with Remote Desktop can't connect to the computer for one of these reasons: 1) Remote access on the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network then goes back to connecting once and immediately disconnecting. All of the updates are installed. The firewall has been correctly configured to let RDP traffic through. The remote setting is "Allow connections from computers running any version of Remote Desktop". I tried creating a second user, and when I can't connect, I can't connect to that user either. I've tried both soft and hard reboots, neither of which help. I've tried connecting from two different computers (both running Windows 7) from two different networks (work and home), and the behavior is the same. Everything else on the server continues to run fine (IIS-served http pages, Tomcat-served java pages, svn, ping). The "fix" that the tech guys supply is simply logging into the console on their end, after which point I can connnect 2 or 3 times again. The event viewer on the server has "authentication failure" (or something similar) events generated when I attempt to log in and can't. I can't get to the actual event at the moment as I'm currently in the can't connect stage, and waiting for the techs to log in. But when I searched for the event earlier this morning I couldn't find anything useful. Can anyone help?

    Read the article

  • PC will POST whenever feels likes it

    - by kyrpas
    I'm really sick of my PC and I'd love to throw it off the 5th floor but unfortunately I don't have this luxury right now. The issues started when I moved to a new house about 2 months ago. I didn't have this problem before. Case: Arctic Cooling Silentium T1 with embedded Fusion 550 Eco 80 PSU. M/B: ASRock A790GMH/128M Gfx: ATI Radeon HD 5770 Here's what's happening almost on a daily basis: I wake up in the morning, switch on the PC and all the fans start spinning. 9/10 the graphics fan stays on 100% and I know it won't post. If I'm lucky, ATI's fan stays on full power for a second, then goes back to normal and I get a normal post but that doesn't happen often. No, instead it's just drives me crazy. When I get no POST I'm trying a lot of different things and what bothers me the most is that they all work. But not always. No... That way I could find out what the hell is going on and we don't want that.. right? So, sometimes it manages to POST if I: remove the keyboard remove the power cable for a few minutes remove the graphics card remove the HDD cables do nothing, just turn it on and off a few times Sometimes it doesn't POST even if I do all of the above. And I end up removing all power cables from the M/B, and connecting all the stuff one by one. Sometimes it works, sometimes it doesn't and I just have to pray and wait. What the hell is that? I'm getting pissed of again just thinking about it. The only solution is to leave it on 24/7 but I don't want to do that. It should be able to turn on and off when I press the power button. I'm not asking much. I'm starting to think there's some weird electricity/power issue but I really don't understand what it is. There's no logical explanation about it. At least I can't find one. Any ideas?

    Read the article

  • ntpdate works, but ntpd can't synchronize

    - by dafydd
    This is in RHEL 5.5. First, ntpdate to the remote host works: $ ntpdate XXX.YYY.4.21 24 Oct 16:01:17 ntpdate[5276]: adjust time server XXX.YYY.4.21 offset 0.027291 sec Second, here are the server lines in my /etc/ntp.conf. All restrict lines have been commented out for troubleshooting. server 127.127.1.0 server XXX.YYY.4.21 I execute service ntpd start and check with ntpq: $ ntpq ntpq> peer remote refid st t when poll reach delay offset jitter ============================================================================== *LOCAL(0) .LOCL. 5 l 36 64 377 0.000 0.000 0.001 timeserver.doma .LOCL. 1 u 39 128 377 0.489 51.261 58.975 ntpq> opeer remote local st t when poll reach delay offset disp ============================================================================== *LOCAL(0) 127.0.0.1 5 l 40 64 377 0.000 0.000 0.001 timeserver.doma XXX.YYY.22.169 1 u 43 128 377 0.489 51.261 58.975 XXX.YYY.22.169 is the address of the host I'm working on. A reverse lookup on the IP address in my ntp.conf file validates that the ntpq output is correctly naming the remote server. However, as you can see, it appears to just roll over to my .LOCL. time server. Also, ntptrace just returns the local time server, and ntptrace XXX.YYY.4.21 times out. $ ntptrace localhost.localdomain: stratum 6, offset 0.000000, synch distance 0.948181 $ ntptrace XXX.YYY.4.21 XXX.YYY.4.21: timed out, nothing received ***Request timed out This looks like my ntp daemon is just querying itself. I am thinking about the possibility that the router-I-don't-control between my test network timeserver and the corporate network timeserver is blocking on source port. (I think ntpdate sends on port 123, which gets it around that filter and is why I can't use it while ntpd is running.) I have email in to the network folks to check that. Finally, telnet XXX.YYY.4.21 123 never times out or completes a connection. The questions: What am I missing, here? What else can I check to try to figure out where this connection is failing? Would strace ntptrace XXX.YYY.4.21 show me the source port ntptrace is sending from? I can deconstruct most strace calls, but I can't figure out the location of that datum. If I can't directly examine the gateway router between my test network and the timeserver, how might I build evidence that it's responsible for these disconnections? Alternately, how might I rule it out?

    Read the article

  • How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment

    - by user69508
    (Please forgive if this is posted in an incorrect forum. We didn’t know exactly where to post it.) We have an ASP.NET Web API single page application - a browser-based app running in IIS to serve up HTML5/CSS3/JavaScript, which talks to the ASP.NET Web API endpoint only to access a database and transfer JSON data. Everything is working great in our development environment - that is, we have one Visual Studio solution with an ASP.NET Web API project and two class library projects for data access. While development and testing on development boxes, using IIS Express to a localhost:port to run the site and access the Web API, everything is fine. Now we need to move it to a production environment (and we’re having problems - or just not understanding what needs to be done). The production environment is all internal (nothing will be exposed on the public Internet). There are two domains. One domain, the corporate domain, is where all users login normally. The other domain, the process domain, contains the SQL Server instance that our app and Web API will need to access. The IT staff wants to put a DMZ between the two domains to house the IIS app and shield the users on the corporate domain from having access into the process domain directly. So, I guess what they want is: corp domain (end users) <– firewall (open port 80) <– DMZ (web server running IIS) <– firewall (open port 80 or 1433????) <– process domain (IIS for Web API and SQL Server) We’re developers and don’t really understand all the networking aspects, so we’re wondering how to deploy our browser/Web API application in this scenario. Do we need to break up our application so that all the client code (HTML5/CSS3/JavaScript/images/etc.) is on the IIS server in the DMZ, while the Web API gets installed on the server in the process domain? Or, does the entire app (client code and Web API) stay together on the IIS server in the DMZ, which then somehow accesses the SQL Server instance to get data? From the IIS server and app in the DMZ, would you simply access the Web API on the server in the process domain by going to "http://server/appname/api/getitmes"? In the second firewall between the DMZ and the process domain, would you have to open port 1433 or just port 80 since the Web API is a HTTP endpoint? Or, is there some better way of deployment (i.e., how ASP.NET Web API single page applications written all in HTML5 and JavaScript supposed to be deployed to production environments?)? I’m sure there are other questions, but we’ll start with these. Thanks!!! (Note: the servers are Win2k8 R2, SQL Server 2k8 R2, and IIS 7.5.)

    Read the article

  • SQL Transactional Replication snapshot not applying

    - by dmch2
    Hi, I'm using SQL Transactional Replication with pull subscriptions to replicate databases (hosting their own distribution database) from several servers across a VPN to a central server. I've got the first 2 databases working fine but the 3rd one is causing me problems. My subscription server is SQL 2008, the source systems are all SQL 2005. The source databases are a few 100Mb in size and contain audit data so are simply growing slowly by adding new records at approx 1kb a second. As far as the replication monitor, Agent logs and event logs show everything is working fine - except that no data appears in my subscription database. The distribution agent doesn't seem to want to read the snapshot (and hence the initial state and schema) from the publisher. New transactions aren't applied although they do seem to be arriving OK as the replication monitor shows things like '5 transactions with 10 commands were delivered'. I would expect (as in previous times) to see statements about data being BCPed in the replication monitor. The snapshot is on the publisher on a shared folder. The subscriber can view the snapshot OK (\\repldata) and the alt snapshot folder is pointing at it. But the distribution agent doesn't seem to be making an attempt to do read it. I tried changing the snapshot path to something that's incorrect and didn't even get an error saying that it couldn't access it. After lots of googling etc I found that sp_MSget_repl_commands is called by the subscriber on the distribution database on the publisher. Running a profiler I can see that it's only called for one agent Id. After a reinit it's called for sequence number 0x0 as expected so I thought that would mean it's would look for the snapshot. However, looking on the publisher I see that there's data for two agents - the snapshot agent and the log reader agent (which is being queries). So I guess I need to tell the distribution agent to get the data for both. But how? and more importantly - why? It worked fine on the other two servers I've replicated. I'm not an SQL novice but this is pretty much my first go at replication so don't be afraid to accuse me of missing something obvious/stupid! I can get log files (eg from the distribution agent) if you want but they don't seem to have any errors in them - it just starts up and starts applying log reader agent changes. Cheers Dave

    Read the article

  • Possible HDD malfunction. Need help in diagnosing

    - by Protheus
    Today when using my PC as I did for almost 4 years I experienced the following: during opening new tab in Opera browser screen froze. Music (AIMP 3) continued to play for about 5 minutes and then stopped too. I tried Ctrl+Alt+Del, but win7 lock screen didn't appear. Caps\Scroll or Num locks didn't switch diodes on keyboard. I rebooted my PC and saw that BIOS suggests me to enter it's settings or load by default. I chose default. It don't see proper boot device (old faitful "insert proper boot" something). After second reboot it said that there is no ExpressGate installed (which i turned off in BIOS years ago). I went into BIOS setting to turn off ExpressGate and see configs: time was not set off, all hard drives present, temp and O.C. settings are nominal (no O.C.) I've inserted my Win7 install disk to try recovery. It did load awfully long (about few minutes) and didn't see current installation. PC was utilized in 24/7 mode for almost all these years. Hardware configuration: ASUS P5Q WS Core 2 Quad Q9300 (2.5GHz no O.C.) MSI geForce GTX 460 4x2 Gb GeIL EVO 2 (AFAIR) Seagate something 750Gb (4 years as system HDD 24/7) WD 1Tb (for random stuff, 5 y.o.) Hitachi 500Gb (for even more random stuff, 6 y.o.) NEC DVDRW (ALL DISKS ARE SATA) Cooler Master Silent Pro 700W Software: Windows 7 AND Kubuntu on the same drive with GRUB loader. Sorry I can't remember HDDs and can't see them right now, but I think their models aren't relevant anyway. My idea is that due to some system error or hard drive glitch i've wrecked my primary HDD's MBR. Nevertheless I don't exclude the possibility of other failure. May it's be that motherboard or it's SATA controller? Doubt it, because all drives are seen in BIOS and I could load from DVD. Maybe GRUB got bugged somehow, although I don't see how it's possible from Windows. But I did install KUbuntu from Windows (i wasn't myself then), maybe GRUB did write itself in some windows partition and got rewriteen in process? Right now I am at work with my flash drive with me and I need some advice how to fix MBR or to hear if it's not MBR. I'm going to buy new HDD (Hitachi 7k2000) because I think that my current HDD is compromised and it's unsafe to use it as system drive, especially 24/7.

    Read the article

  • Recovering from backup without original install media

    - by KGendron
    A machine from my old job had a complete hard drive failure. I have backups but I'm running into severe problems restoring from them. The only install media was a secondary restore partition on the system's hard drive. I hate whoever came up with that idea more than i can possibly express with words. I spent several days trying to recover the disk - it is pretty well shot and none of my best tricks could even get it to show up in the bios/ The machine that broke is an hp with xp media center edition on it (I don't know why either). The backups were created using the default windows backup tool - I have .bfk file on an external hardrive that i am trying to restore from. I've replaced the hard drive. My home machine is running windows 7 64bit and i'm trying to use it as a platform to restore to the other disk. I downloaded the window 7 nt-restore utility, however no matter what i do it restores to my C drive rather than the specified drive. Fortunately win7 security settings prevented it from being a complete disaster - but still not a happy thing. I tried firing up the xp virtual machine. I can browse to the backups but it says they are invalid and refuse to let me view/ continue with the restore. I tried installing XP to an extra harddrive on my machine - however it bluescreens on me during the install process and I cry. I tried installing xp pro to the new drive and attempted to restore over it, it of course blackscreened on me as that was a stupid idea. I made two partitions on the new hard drive (Apparently the bios on this accursed piece of junk doesn't allow hd partitions larger than 200G anyways and thus fails 40 minutes into the install with an ever-descriptive "Disk Read Error". Guess how i spent last weekend? My last idea was to install xp pro to the second partition and then use it to restore from backup to the first. After the first restart it gives me the error "Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware". My brain made one of those bad hard drive clicky noises. I've tried several boot disks but they don't seem to work. If anyone has a link to a good one it would be greatly appreciated. Anyone have any more ideas? - I really hate asking on what seems like such a simple issue but i am quite literally at my wit's end. Thanks - and sorry for the really long post.

    Read the article

  • If Nvidia Shield can stream a game via wifi, why can I not do the same via ethernet to any other PC?

    - by Enigma
    I think it absurd that a wireless game streaming solution is the *first to hit the market when a 1000mbps+ Ethernet connection would accomplish the same feat with roughly 6x the available bandwidth. I can only assume that there must be some reason behind this or a limitation preventing this, but what? 150mbps wifi is in no way superior to a 1000mbps LAN connection aside from well wireless mobility. Not only that but I have a secondary laptop and desktop which should by hardware comparison completely outperform anything the Tegra in the Nvidia Shield can do. Is this all just a marketing scheme to force people to buy the shield for the streaming benefit? Chief among these is that NVIDIA’s Shield handheld game console will be getting a microconsole-like mode, dubbed “Shield Console Mode”, that will allow the handheld to be converted into a more traditional TV-connected console. In console mode Shield can be controlled with a Bluetooth controller, and in accordance with the higher resolution of TVs will accept 1080p game streaming from a suitably equipped PC, versus 720p in handheld mode. With that said 1080p streaming will require additional bandwidth, and while 720p can be done over WiFi NVIDIA will be requiring a hardline GigE connection for 1080p streaming (note that Shield doesn’t have Ethernet, so this is presumably being done over USB). Streaming aside, in console mode Shield will also support its traditional local gaming/application functionality. - http://www.anandtech.com/show/7435/nvidia-consolidates-game-streaming-tech-under-gamestream-brand-announces-shield-console-mode ^ This is not acceptable for me for a number of reasons not to mention the ridiculousness of having a little screen+controller unit sitting there while using a secondary controller and screen instead. That kind of redundant absurdity exemplifies how wrong of a solution that is. They need a second product for this solution without the screen or controller for it to make sense... at which point your just buying a little computer that does what most other larger computers do better. All that is required, by my understanding, is the ability to decode H.264 video compression and transmit control/feedback so by any logical comparison, one (Nvidia especially) should have no difficulty in creating an application for PC's (win32/64 environment) that does the exact same thing their android app does. I have 2 video cards capable of streaming (encoding) H.264 so by right they must be capable of decoding it I would think. I haven't found anything stating plans to allow non-shield owners to do this. Can a third party create this software or does it hinge on some limitation that only Nvidia can overcome? (*) - perhaps this isn't the first but afaik it is the first complete package.

    Read the article

  • On ESXi, guest machines hang for significant intervals compared to real machines. How can I fix this?

    - by Tarbox
    This is ESXi version 5.0.0. We plan on upgrading to 5.5 eventually. I have four code profiles, two taken on a real, unvirtualized machine, two taken on a virtual machine. Ordering the list of subroutines by time spent in each one, the two real profiles are practically identical. The two virtual profiles are different from each other and from the real profiles: a subset of subroutines are taking a lot more time on the virtual machines, and the subset is different for each run. The two virtual profiles take a similar amount of time, which is 3 times the amount of time the real profiles take. This gross "how long does it take?" result is consistent after hundreds of tests across three different virtual machines on two different host machines -- the virtual machine is just slower. I've only the code profiling on the four, however. Here's the most guilty set of lines: This is the real machine: 8µs $text = '' unless defined $text; 1.48ms foreach ( split( "\n", $text ) ) { This is the first run on the virtual machine: 20.1ms $text = '' unless defined $text; 1.49ms foreach ( split( "\n", $text ) ) { This is the second run on the virtual machine: 6µs $text = '' unless defined $text; 21.9ms foreach ( split( "\n", $text ) ) { My WAG is that the VM is swapping out the thread and then swapping it back in, destroying some level of cache in the process, but these code profiles were taken when the vm in question was the only active vm on the host, so... what? What does that mean? The guest itself is under light load, this is a latency problem for my users rather than throughput. The host is also under a light load, if I knew what resources to assign where, I could do it without worrying about the cost. I've attempted to lock memory, reserve cpu, assign a restrictive affinity, and disable hyperthread sharing. They don't help, it still takes the VM 2-4x the amount of time to do the same thing as the real machine. The host the tests were run on is 6x2.50GHz, Intel Xeon E5-26400 w/ 16gigs of ram. The guest exhibits the same performance under a wide combination of settings. The real machine is 4x2.13GHz, Xeon E5506 w/ 2 gigs of ram. Thank you for all advice.

    Read the article

  • Cooling Server Rack with Water? Sensible? Reuse energy for small installation?

    - by TomTom
    First - this is not a shopping question, this is not so much about concrete prices but about general feasibility. Makes no sense to get looking fo ra manufacturer it the approach is bad. I am moving my company to new Offices in September, and among them we will expand and consolidate our number crunch cluster. It is so far in a data center. I have a nice room in the basement prepared now. I think about cooling. We will likely run up a power usage of around 10kw by end of the year. That is a LOT of stuff, and cooling will be expensive. I am located in south Poland, close to the German border. This is an area where water is available for relatively cheap price - "wasting water" is not a concern here. My situation is thus a lot different for example than in Spain ;) Physics tells me that to heat 1 liter of water by 1 degree I use 1 Calorie (1KCal), and a kwh power is (and we can assume 100% efficiency - water heaters are pretty efficient) 750 Calories. That means that 1 KWH is 750 liter by 1 degree. 10kw and a 20 degree heat would mean that per hour I need 375 liters. That is 6.25 liters per minute and not WHAT much ;) We talk 270 cubic meters here. Even in summer, the significant underground pipes really cool down the water a LOT more ;) Question: This such an approach feasible? Anyone done that? We talk of a 10kw installation for now. Is it feasible to reuse that heat? The alternative is a decent cooling system that WILL use around 2.5kwh for running. Dropping the water would basically (a) get me a quite cold input compared to the outside air even in summer (I.e. a lower temperature medium to drop the heat in) and (b) replace the need to actually have the outside cooling (which may b problematic - if the air is 22 degree, that is a LOT to fight off, but OTOH the water will be quite cold). I also would possibly save the investment for the outside part of the cooling circuit. Now, second question - is there a feasible way to heat a house with that? ;) After all, brutally speaking, it is a LOT of energy in that water ;) If it is a bad idea, I stop here - if it is not, I start looking for suppliers. Maybe my math is wrong?

    Read the article

  • What DNS server to use for dynamic load-balancing of website?

    - by Marki555
    I will have 2 servers in different datacenters (different countries) and I want to use DNS load-balancing mainly for High Availability of website hosted on those 2 servers. It is just ad tracking site, which records hit in local database and returns few lines on html code. I want to return 2 A records each time because of DNS pinning in browsers (if one server fails, browser will try second A record which it has already cached). Both servers will be acting also as DNS servers for redundancy. Now comes my proposed solution: I will use BIND and have both servers as a master for that zone. On each server there will be running script, which will periodically test availability (http) of both servers and remove IP from DNS in case of failure. Now the questions :) 1) Is BIND suitable for this solution? I think BIND performance is good and it is easy to manipulate the zone file via script. And as I will modify the zone only in case of failure/maintenance, the modifications (and thus bind reload) won't be often. 2) I plan to use TTL of 5 minutes. The website will have about 1000-3000 req/s but from distinct clients (each IP only 1-3 requests), so I think the DNS load won't be too much. I suppose their ISPs will cache the responses for those 5 mins. Is there any reason to lower the TTL even more? 3) Is my master-master approach good? Or should I make one of the servers master and the other one slave? Right now each server can monitor both itself and the other one. If only webservice fails, both DNS nodes will notice it. If the whole server fails, then the remaining DNS node will notice it and the failed node will not answer DNS queries anyway. 4) Is it a big issue when one NS server does not respond to queries? If yes, I can make a third DNS, so anytime at least 2 of them would accept queries... 5) Should I rewrite the zone file via script, or just use dynamic DNS update (for example via nsupdateutility)?

    Read the article

  • Apache VirtualHost Blockhole (Eats All Requests on All Ports on an IP)

    - by Synetech inc.
    I’m exhausted. I just spent the last two hours chasing a goose that I have been after on-and-off for the past year. Here is the goal, put as succinctly as possible. Step 1: HOSTS File: 127.0.0.5 NastyAdServer.com 127.0.0.5 xssServer.com 127.0.0.5 SQLInjector.com 127.0.0.5 PornAds.com 127.0.0.5 OtherBadSites.com … Step 2: Apache httpd.conf <VirtualHost 127.0.0.5:80> ServerName adkiller DocumentRoot adkiller RewriteEngine On RewriteRule (\.(gif|jpg|png|jpeg)$) /p.png [L] RewriteRule (.*) /ad.htm [L] </VirtualHost> So basically what happens is that the HOSTS file redirects designated domains to the localhost, but to a specific loopback IP address. Apache listens for any requests on this address and serves either a transparent pixel graphic, or else an empty HTML file. Thus, any page or graphic on any of the bad sites is replaced with nothing (in other words an ad/malware/porn/etc. blocker). This works great as is (and has been for me for years now). The problem is that these bad things are no longer limited to just HTTP traffic. For example: <script src="http://NastyAdServer.com:99"> or <iframe src="https://PornAds.com/ad.html"> or a Trojan using ftp://spammaster.com/[email protected];[email protected];[email protected] or an app “phoning home” with private info in a crafted ICMP packet by pinging CardStealer.ru:99 Handling HTTPS is a relatively minor bump. I can create a separate VirtualHost just like the one above, replacing port 80 with 443, and adding in SSL directives. This leaves the other ports to be dealt with. I tried using * for the port, but then I get overlap errors. I tried redirecting all request to the HTTPS server and visa-versa but neither worked; either the SSL requests wouldn’t redirect correctly or else the HTTP requests gave the You’re speaking plain HTTP to an SSL-enabled server port… error. Further, I cannot figure out a way to test if other ports are being successfully redirected (I could try using a browser, but what about FTP, ICMP, etc.?) I realize that I could just use a port-blocker (eg ProtoWall, PeerBlock, etc.), but there’s two issues with that. First, I am blocking domains with this method, not IP addresses, so to use a port-blocker, I would have to get each and every domain’s IP, and update theme frequently. Second, using this method, I can have Apache keep logs of all the ad/malware/spam/etc. requests for future analysis (my current AdKiller logs are already 466MB right now). I appreciate any help in successfully setting up an Apache VirtualHost blackhole. Thanks.

    Read the article

  • Why is my concurrency capacity so low for my web app on a LAMP EC2 instance?

    - by AMF
    I come from a web developer background and have been humming along building my PHP app, using the CakePHP framework. The problem arose when I began the ab (Apache Bench) testing on the Amazon EC2 instance in which the app resides. I'm getting pretty horrendous average page load times, even though I'm running a c1.medium instance (2 cores, 2GB RAM), and I think I'm doing everything right. I would run: ab -n 200 -c 20 http://localhost/heavy-but-view-cached-page.php Here are the results: Concurrency Level: 20 Time taken for tests: 48.197 seconds Complete requests: 200 Failed requests: 0 Write errors: 0 Total transferred: 392111200 bytes HTML transferred: 392047600 bytes Requests per second: 4.15 [#/sec] (mean) Time per request: 4819.723 [ms] (mean) Time per request: 240.986 [ms] (mean, across all concurrent requests) Transfer rate: 7944.88 [Kbytes/sec] received While the ab test is running, I run VMStat, which shows that Swap stays at 0, CPU is constantly at 80-100% (although I'm not sure I can trust this on a VM), RAM utilization ramps up to about 1.6G (leaving 400M free). Load goes up to about 8 and site slows to a crawl. Here's what I think I'm doing right on the code side: In Chrome browser uncached pages typically load in 800-1000ms, and cached pages load in 300-500ms. Not stunning, but not terrible either. Thanks to view caching, there might be at most one DB query per page-load to write session data. So we can rule out a DB bottleneck. I have APC on. I am using Memcached to serve the view cache and other site caches. xhprof code profiler shows that cached pages take up 10MB-40MB in memory and 100ms - 1000ms in wall time. Pages that would be the worst offenders would look something like this in xhprof: Total Incl. Wall Time (microsec): 330,143 microsecs Total Incl. CPU (microsecs): 320,019 microsecs Total Incl. MemUse (bytes): 36,786,192 bytes Total Incl. PeakMemUse (bytes): 46,667,008 bytes Number of Function Calls: 5,195 My Apache config: KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 3 <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 120 MaxRequestsPerChild 1000 </IfModule> Is there something wrong with the server? Some gotcha with the EC2? Or is it my code? Some obvious setting I should look into? Too many DNS lookups? What am I missing? I really want to get to 1,000 concurrency capacity, but at this rate, it ain't gonna happen.

    Read the article

  • Can't install .NET framework 4.0 on Windows XP professional version 2002 SP3 (OS bug?)

    - by that guy
    .NET framework 4.0 install fails on Windows XP professional version 2002 SP3: I tried to run setup using "run as..." to make sure the admin rights are used ("protect my computer..." tick was deselected of course). I tried everything: installing using online/offline setup, windows update. install goes a little and then "rolls back" and says: Installation did not succeed .NET Framework 4 has not been installed because: Fatal error during installation. for more information about this problem, see the log file. the full log: http://pastebay.net/1433771 Any ideas? EDIT1: I have found this in the log: "BlockIf: You must install the 32-bit Windows Imaging Component (WIC) before you run Setup. Please visit the Microsoft Download Center to install WIC, and then rerun Setup...." So I found it, and launched "wic_x86_enu.exe" - but it said: WIC Setup error Newer version of update is already on the system. I have already installed: .NET framewrok 2.0 SP2 .NET framewrok 3.0 SP2 .NET framewrok 3.5 SP1 but I need 4.0 . EDIT2: another attempt and it's log. (this time better copy of log file): http://pastebin.com/gmGfbM9a (copy to notepad and save as .htm and open with internet browser). I have tried all the solutions I could find - and nothing helped. I have found something weird: when I formatted the hard drive and installed windows xp again - the .NET framework 4.0 installed ok, but when I plugged my 100Mbit internet cable - the operating system kind off "locked itself" and the bug returned - I could no longer install .NET framework 4.0 again. There was no reason for that to happen, for example I have windows server 2003 in local network, but I don't have active directory enabled on it or anything like that - the server just has some folders shared and thats all (all server's "features" are default). I had the second pc with the same problem - with XP on it too. This seems like the bug of Operating System to me. I couldn't find what was causing the problem. After many days I gave up: backuped everything, formatted HDD and installed Windows 7 professional 64bit. .NET framework 4.0 installed with no problem on it.

    Read the article

< Previous Page | 591 592 593 594 595 596 597 598 599 600 601 602  | Next Page >