Search Results

Search found 111248 results on 4450 pages for 'end user computing'.

Page 598/4450 | < Previous Page | 594 595 596 597 598 599 600 601 602 603 604 605  | Next Page >

• Hard Disk Not Counting Reallocated Sectors

  - by MetaNova

  I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

  Read the article

• Very high-pitched noise when computer does something intense?

  - by Starkers

  "Intense" is the best word I can use to describe it because I'm not sure what it is, whether it's RAM, GPU or CPU. If I pan the camera in unity: A high pitched noise issues from the computer. The picosecond I start panning the sound starts. Stops the picosecond I stop panning. If I start an infinite loop: 2.0.0p247 :016 > x = 1 => 1 2.0.0p247 :017 > while x < 2 do 2.0.0p247 :018 > puts 'huzzah!' 2.0.0p247 :019?> end huzzah! huzzah! huzzah! An identical high pitched noise can be heard. I don't think it's the GPU due to this simple experiment. Or any monitor-weirdness (although the sound does sound like one of those old CRT monitors if you're old enough to be young when those things were about) The CPU? Or maybe my SSD? It's my first SSD and the first time I've heard this noise. Should I be worried? Regardless, what's causing this sound? I can't think what would cause such high frequency vibrations. I built the PC myself. Not enough heat paste on the CPU? Too much? Just no idea what's going on. Info: CPU Type QuadCore Intel Core i5-3570K, 3800 MHz (38 x 100) Motherboard Name Asus Maximus V Extreme Flash Memory Type Samsung 21nm TLC NAND Video Adapter Asus HD7770

  Read the article

• How to convert JPEG JFIF files to JPEG Exif format?

  - by tigrou

  I recently put the SD card of my camera in a Windows 7 PC and start browsing pictures on it. I noticed some were not aligned correctly and use rotate feature included in Windows Photo Viewer in order to view them as I wanted. What I didn't know is that when rotate feature is used, it also overwrite the picture when pressing next or previous button resulting in a possible loss of quality (which is in my opinion a bad idea, app should at least warn user of what will happened when using such a feature). After that, I re-inserted the SD card back in my camera and bad surprise happened : the rotated picture could not be previewed anymore. Instead, i got a black screen saying "Incompatible JPEG format". Other files (untouched) are still working ok. To try to understand what happened I opened a JPEG file from camera and one generated on windows 7 in a hex editor. Here is the difference : The camera JPEG files have a Exif tag in them (with 0xE1 in header). Other JPEG files (Windows 7) have first a JFIF tag in it, followed by a Exif tag (with 0xE0 in header). So if i understand it well, both are JPEG files, but using a different internal format. Here is my question : is it possible (using some tool) to convert JFIF files to Exif format ? I understand that original camera files have been reencoded and thus lose some quality (getting originals back is impossible). What i want know if convert them from JFIF back to Exif (without a second loss of quality if possible...)

  Read the article

• Windows 7 DVD doesn't boot up, neither does USB. :'(

  - by Manan Shah

  My problem is that i'm not able to install windows 7. Been trying to install this since past 1 week. The methods i've tried are: I have a windows 7 bootable DVD which doesnt boot up. (I've set BIOS to boot from DVD ROM first but it just won't boot from the DVD). Tried to install Windows 7 from the same DVD to a friend's PC and it worked. So the DVD has no issues. I tried to run 'Setup.exe' from within the DVD. The two options pop-up 'Check compatibility' and 'Install now'. On clicking install now, after sometime, an error is encountered with the message 'Windows was unable to create a required installation folder' error code:0x8007000D. I am running Windows XP Professional and there's only one user on the PC which is the Admin, so i do not know why is the setup not getting permissions. I've also uninstalled my antivirus, CD burning software, disabled firewall and disconnected all other devices, but its still the same. I tried to install it from a USB device by making it bootable but that too doesnt work. (Yes the mobo supports booting from the USB). The problem is that XP does not recognize a 'USB' device on boot. Rather it shows this USB stick as a removable 'Hard Drive'. Furthermore, i changed the order of Hard Drive boot to boot from this removable Hard Drive first, it still boots my existing OS. Is there anything else that can be done? Any help would be greatly appreciated. :) Please ask if any other information is required, this post is becomimg increasingly long to add any other details. PS: I want to dual boot windows 7 with my existing XP, but that would be after i manage to run the windows 7 setup in the first place. PPS: Please bare with any 'not-so-technical' terms, i am a beginner with this. Again, thank you for taking the time and trying to help, really appreciate it. :)

  Read the article

• How do I uncompress vmlinuz to vmlinux?

  - by Lord Loh.

  I have already tried uncompress, gzip, and all other solutions that come up as google results and these have not worked for me. To get just the image search for the GZ signature - 1f 8b 08 00. > od -A d -t x1 vmlinuz | grep '1f 8b 08 00' 0024576 24 26 27 00 ae 21 16 00 1f 8b 08 00 7f 2f 6b 45 so the image begins at 24576+8 => 24584. Then just copy the image from the point and decompress it - > dd if=vmlinuz bs=1 skip=24584 | zcat > vmlinux 1450414+0 records in 1450414+0 records out 1450414 bytes (1.5 MB) copied, 6.78127 s, 214 kB/s Got these instructions verbatim from a forum online: http://www.codeguru.com/forum/showthread.php?t=415186 This process does not work for me and end up giving errors that states file not found 0024576 and all subsequent numbers. How do I proceed extracting vmlinux from vmlinuz? Thank you. EDITED: This is a reverse engineering question. I have no access to the distro to install any RPM or recompile. I start with nothing but vmlinuz.

  Read the article

• Change Windows 7 Explorer's Details Pane limits

  - by Paul

  For some reason, MS decided to completely kill the status bar's functionality in Win7 (and maybe Vista, but I don't know for sure). I have tried all possible options such as Classic Shell and so on. Basically, the one thing I miss most is seeing at a glance the total size of my selected files. I know I can press Alt+Enter or whatever, but that's not the point. The point is that the so-called 'details' pane stops providing details if more than 15 files are selected! WTH? Cannot understand the reason behind such a stupid arbitrary limit, that doesn't seem to be user-configurable at all. Anyway, what I'm looking for is a way to change that limit, either via the registry or otherwise. If changing the limit isn't possible, would it be possible for some programming genius to create a very small optimized light-weight non resource-hungry (you get the idea!) program whose sole purpose will be to automatically click the "Show more details..." link in the details pane after every file selection? For bonus points, the program should wait for a second or two after file selection is complete to do this, so that selecting multiple files in quick succession doesn't hit the HDD repeatedly. Any takers for the challenge? :)

  Read the article

• Applications randomly alt-tab? (especially full screen games)

  - by Henry Scotts

  I'm not sure when this began, how it happens, or why it happens, but it is quite bothersome and apparently random. Just randomly throughout the day my computer will just go to the desktop. I could be in a full screen game and it will just immediately alt tab and present the desktop. Or I could be watching a movie and this happens. Sometimes it happens once every three hours and other times (just today actually) it did it twice in the span of 30 seconds. I am positive I am not pressing a hotkey because I launched a game, sat idle, and noticed it alt tab while cleaning up around my room after about 20 minutes. Sometimes it goes days without this happening. Specs: Windows 7 Ultimate 64 Bit, 10 gigs of RAM, GeForce GTX 260, Intel Xeon CPU. I also have basically nothing running when it happens other than the game and FireFox. My FireFox add-ons: Adblock Plus, Download Statusbar, Firebug, FirePHP, lazarus form recovery, tree-style-tabs, yslow. I doubt FireFox is causing the issue but I figured I'd include it anyway because it is the only application I have running when it happens. As for user processes I have running: VCDDaemon (context menu for virtual clone drive), razerhid (mouse), OSD, taskhost, dmw (desktop window manager), anyfullscreengame, audiorepeater, netsession_win, explorer, razerofa, tsvncache, firefox, plugin-container, and EKIJ5000MUI (printer). Whew. Okay. That was a lot of information. If someone could diagnose this I would be most grateful for this has been around with me for years.. Thanks for reading! PS: I doubt it's a virus because I never download illegal software and pretty much only browse Reddit and Stackexchange and play games. If it was a virus it would be a pretty lame one.. Hah..

  Read the article

• Fix Video timelines

  - by Josh

  So, I have been going through and riping all of my DVD's and it seems that the way to get the highest quality out of these is to have DVD Shrink de-encrypt, rip, and decompress, the DVD's. After that I usually end up with a high quality (high size) set of .vob files in a classic DVD structure. Then I use a python script that I wrote to automate the process of finding the title sequence and then combining all of the title sequences' .vob files together into one file(similar to the "copy /b" command in windows), and then changing the extension to .mpg (a more widely supported format then .vob). This allows me to get a high quality rip in about 40 min. The problem comes in playing the files. I need all of the ripped dvd's to play on my media computer using windows media center but windows media center (and vlc for that matter) all think that the video files are anywhere from 5 min. to 0 min. which is not a problem (the video will still play all the way through) but if you want to pause it, when it is unpaused the video will start all the way over (Also fast forward and rewind don't work). I suspect that it is something wrong with the way the timeline is encoded in the video file, various forums on the internet recommended using virtualdub to fix the errors. But when I try to open the file virtual dub says that the file is not in mpeg-1 encoding and may be in mpeg-2. Is there any way to fix this? PS: I am aware that there was a similar question but it hasn't had any activity for 2 months and is dealing more with wmv files.

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• How can I make non-anti-aliased text look good in Firefox on Mac OS X?

  - by cosmic.osmo

  After being a Windows user for the last 10 years, I got a MacBook Pro, which I'm working on configuring to my liking. I find small-size anti-aliased text to be blurry and hard to read, so I typically disable it. I've found the settings in the General Control Panel, and used TinkerTool to increase the anti-alias threshold size to 18pt. Mac OS X and other applications appear to respect these settings. A problem appears when I use Firefox. By default, it's configured to ignore the Mac OS anti-alias settings. This is changed by going to about:config, and setting gfx.use_text_smoothing_setting = true (default is false). However, even with this setting, it appears Firefox is still rendering the fonts under the assumption that they will be anti-aliased, which results in very odd and uneven spacing, as you can see in this example (pay attention to the placement of the "s" in "Disable"): With anti-aliasing: Without anti-aliasing: How can I configure Firefox to both not use anti-aliasing and to use correct font spacing? I'm using Mac OS X Lion and Firefox 5.

  Read the article

• Where is '/host' declared for mount in Wubi (Ubuntu 9.10)?

  - by Pedro

  Hi! I'm using Wubi (ubuntu 9.10), and I couldn't find where '/host' mountpoint is declared for mounting. There's no entry in fstab, but it's listed in /proc/mount and mounted at boot time. Any ideas? pedroel@ubuntu:~$ cat /proc/mounts rootfs / rootfs rw 0 0 none /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 none /proc proc rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,relatime,mode=755 0 0 /dev/sda1 /host fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 0 0 /dev/loop0 / ext4 rw,relatime,errors=remount-ro,barrier=1,data=ordered 0 0 none /sys/kernel/security securityfs rw,relatime 0 0 none /sys/fs/fuse/connections fusectl rw,relatime 0 0 none /sys/kernel/debug debugfs rw,relatime 0 0 none /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0 none /dev/shm tmpfs rw,nosuid,nodev,relatime 0 0 none /var/run tmpfs rw,nosuid,relatime,mode=755 0 0 none /var/lock tmpfs rw,nosuid,nodev,noexec,relatime 0 0 none /lib/init/rw tmpfs rw,nosuid,relatime,mode=755 0 0 /dev/loop1 /home/pedroel/Downloads ext4 rw,relatime,errors=remount-ro,barrier=1,data=ordered 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 gvfs-fuse-daemon /home/pedroel/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=1000,group_id=1000 0 0 /dev/mapper/isw_efhafcifi_RAID_Volume01 /media/RAID_D fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 0 0 pedroel@ubuntu:~$ cat /etc/fstab # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # proc /proc proc defaults 0 0 /host/ubuntu/disks/root.disk / ext4 loop,errors=remount-ro 0 1 /host/ubuntu/disks/pedro.disk /home/pedroel/Downloads ext4 loop,errors=remount-ro 0 1 /host/ubuntu/disks/swap.disk none swap loop,sw 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0 Thanks in advance, Pedro

  Read the article

• Terminate child processes on ctrl-c

  - by jackweirdy

  In tiny core linux, I have the following script: #!/bin/sh # ~/.X.d/freerdp.sh rdp(){ while true do xfreerdp -f [IP Address] done } rdp & It's pretty simple; when X starts up and checks the .X.d directory (as is the case in tiny core) it finds and executes this script. The script starts up freerdp and keeps a connection open to the server by restarting it whenever it closes. As you can see from the rdp & line, the function is run in the background to allow X to continue its startup routine. The problem is that whenever I cancel X with a Ctrl-Alt-Backspace the rdp process doesn't die. I'm looking for a way to kill the process as soon as X finishes, either through: A) a script, executed on X closing, which kills the process or B) by modifying the script to check the return value of the xfreerdp command. NB - if the solution does check the return value, it must only end if the command fails to open the X display. For that reason, if you could point me to a reference for xfreerdp return values I'd be grateful.

  Read the article

• How can I restore my laptop from Windows 7 to its original Windows Vista recovery partition?

  - by Cam Jackson

  I bought my Acer laptop 4 years ago with Vista Home Premium x86. It has a recovery partition that I have used successfully in the past to format everything and reinstall Windows to factory settings. I have since upgraded to Windows 7, but I now need to get back to my original installation. Not sure what it's called, but I can successfully get into this recovery thingy: However, when I click the third option (for me I think it says 'Windows Image Recovery' or something like that) it tells me that it can't find any images to recover from :( I have checked and I don't have a windows.old that I can recover from either. One final note, if I launch diskmgmt.msc, these are the partitions: Why is the first partition shaded? Does that mean anything? Both of the 'unlettered' partitions are 100% empty. Did the Windows 7 upgrade process format my Vista system recovery partition?! And finally: How can I get back to my factory settings? EDIT: I did see this question, but neither of the answers apply to my situation. Edit to address jdh's answer: From what I can tell, I never get the option to boot the Vista recovery partition. After hitting F10, I get this screen, except it's partition 2, and I don't have the IN/MINT bit: I hit Escape, and then I get this screen, except without Ubuntu listed, and without the auto-countdown thing: I hit F8, and then I get this screen: I hit Enter on the first option, I end up at the screen in the first screen shot. As I said, from there I click the third option, and it fails to find the image, which I guess makes sense if it's only looking for a Windows 7 recovery. So I either need to make the Windows 7 tool see the Vista recovery partition, or I need the boot loader (?) to let me select Vista earlier in the process. Any ideas?

  Read the article

• How to transform a csv to combine matching rows?

  - by Christian Wolf

  I have a CSV file with some transaction data. Let's say date, volume, price and direction (sell/buy). Additionally there is a ID for each transaction and on each closing transaction (the newer one) there is a reference to the corresponding transaction. Classical database referencing. Now I want to do some statistics and draw some plots. This could be done via Octave, LaTeX/TikZ, Gnuplot or whatever. To do this I need both buy and sell price in one row. My thought was to preprocess the CSV to get another CSV containing the needed information and then to do the statistics. In the end I'd like to have a solution based on scripts and not on a spreadsheet as data might change often (exported from online DB). My actual solution (see http://paste.ubuntu.com/6262822/ ) is a bash script that parses the CSV line by line and checks if there exists a corresponding transaction. If found, a new row is written to the destination CSV. If not a warning is printed. The bad news: For each row in the source file I have to read the whole file a few times. This causes long running times of 10sec for 300 lines. As the line number might rise soon (10k lines), this is not perfect. I am aware, that there are many shells to be opened in the script which might cause the performance problems. Now my questions: Is bash/awk/sed/.... a good way to do things? Should I first import all data into a "real" local database to use SQL? Is there an easy way to achieve the desired results?

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• Delete on windows vista and seven -- discovery process

  - by M'vy

  Hi SUs! I've recently encountered a problem. Using svn at work I needed to clear some space. As you may know svn directories are full of sub-directories and files. So the delete process begins with a step of discovering the items to be deleted (I guess this is for displaying the progress bar). But in my case it ended up to be still running after I watched Braveheart (Off-topic: good film in my opinion. On-topic: and it last 2h50) and counting 440 000+ files. I finally decided to cut off the process and use the good old cmd with a del <directory> to do the job. (Done in some minutes) So I'm wondering if someone know how to override the system to make it actually begins the process while scanning the other items? At the end, I just want the file to be deleted and I don't care the number of files to be deleted. On the contrary I care about the time it takes. Thanks

  Read the article

• Moving my OpenID from Livejournal to... something else.

  - by T-Boy

  I've actually been an early user of OpenID, although there are still some questions that I've had with OpenID that I've never really had satisfactorily answered. Now, I understand that if I have full control over my domain, I can set it up so that I can delegate the task of authenticating to another OpenID service provider. The problem is, what I'd like to do is to get the Livejournal server to pass the authentication to someone else, instead of having LJ doing it. Preferably what I'd like to do is get Livejournal, when asked by a authenticating provider, say, "No, I don't do it anymore -- go to this address". The plan was that this address would then be in a domain I fully control, which then would pass it on to whichever service provider I choose. I don't even know if I've gotten my understanding of OpenID right, if all this shenanigans are necessary, if my question makes sense, or if it's even possible with a service provider like Livejournal. (tried tagging this with livejournal, and it told me I couldn't, because I don't have enough reputation. Oh well; one must start somewhere. Sorry for the inconvenience!)

  Read the article

• Is my OCZ SSD aligned correctly? (Linux)

  - by Barney Gumble

  I have an OCZ Agility 2 SSD with 40 GB of space. I use it as a system drive in Debian Linux (Squeeze) and in my opinion it's really fast. But I've read a lot on aligning partitions and file systems... And I'm not sure if I succeeded in aligning the partitions correctly. Maybe the SSD could be even faster?? ;-) I use ext4 and here is the output of fdisk -cul: Disk /dev/sda: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: [...] Device Boot Start End Blocks Id System /dev/sda1 * 2048 73242623 36620288 83 Linux /dev/sda2 73244670 78159871 2457601 5 Extended /dev/sda5 73244672 78159871 2457600 82 Linux swap / Solaris My partitions were created just by the Debian Squeeze setup assistant. So I didn't care about the details of partitioning. But now I think maybe the installer didn't align it correctly? Actually, 2048 looks good to me (better than odd values like 63 or something like that) but I've no idea... ;-) Help plz! According to some "SSD Alignment Calculator" I found on the web, the OCZ SSDs have a NAND Erase Block Size of 512kB and their NAND Page Size is 4kB. 2048 is divisible by 4 and 512. So are the partitions aligned correctly?

  Read the article

• What is the proper way of debugging a slow Windows installation?

  - by Niklas

  You know the drill - you've been asked to check why you cousin's computer is running slow. I was there yesterday. Being a Mac user since 2007 I haven't really dug deep in Windows internals in the past five years. Googling for answers reveals many, many different answers: broken registry, spyware, antivirus program, fragmented disk, turning of visual effects etc. In this particular case I was asked to look at a two year old HP laptop with Vista. Windows was running incredibly slow and even opening up a new explorer window took almost a minute. I ended up doing everything of the above: running cc cleaner, defragmenting the disk, turning off visual effects, turning off norton and a bunch of other things people believe have an impact on Windows performance. Now I'd like to understand this in depth. Is there a proper, "scientific" if you so will, way of debugging and understanding where the problem with a slow running Windows installation lies? (In my particular case this concerned Windows Vista but let's try to create general guide for XP and Windows 7 too). To me, it seems wrong to just run a bunch of different tools without understanding the underlying cause of the error.

  Read the article

• Good references to know why has my computers stopped responding me

  - by Peterstone

  Hello all! I´m a windows xp user (but not for much time...) and I usually see how my computer stop of responding me. The process is this: Firsly it became totally stopped or very slow for certain periods of 5 minutes. How could I do? After that it gets stopped (Even not totally because If I click on the bar I see a blinking response in the bar botton of the program I click on. It´s could be anything related with security (like the firewall or some virus)? Computer university: I usually experience this, using Matlab (R2007a) with System Generator (its respective compatible version) My personal laptop: It´s usually works well but when stopped periods became to appears I know in not much time it will became totally stopped. I usually see how Word 2007 get stopped and after a while my windows xp gets stopped. (well I can access to the the manage task pressing ctr+alt and...). The only solution I see is to kill program by program... My petition: Please, I need good references that help me how to think in order to avoid or to manage the problems previously described. Does anyone know usefull books or articles? EDIT: Laptop: OS: XP Home Edition Version 2002 SP3 Hardware: HP Mini Intel(R)Atom(TM) CPU N270 @1,60GHz 1.99 GB RAM University Computer: OS: XP Profesional SP3 Hardware: AMD Athlon(tm) XP 1800+ 1.54 GHz, 768 MB RAM

  Read the article

• Failing to load rootfs: Ubuntu 10 + grub2 + rootfs ext4 w/ RAID1

  - by James

  I am having problems booting a new Ubuntu 10 (server) install. My primary HD (/dev/sda) is laid out as follows: Device Boot Start End Blocks Id System /dev/sda1 * 1 18 144553+ 83 Linux <-- /BOOT /dev/sda2 19 182401 1464991447+ 5 Extended /dev/sda5 19 2207 17583111 fd Linux raid autodetect /dev/sda6 2208 11934 78132096 fd Linux raid autodetect <-- / (ROOTFS) /dev/sda7 11935 182401 1369276146 fd Linux raid autodetect The rootfs is part of a RAID1 (software) array (currently degraded): # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md2 : active raid1 sda6[1] 78132032 blocks [2/1] [_U] The UUIDs for the partitions are as follows: # blkid /dev/sda1 /dev/sda1: UUID="b25dd301-41b9-4f4d-9b0a-0e31713dd74c" TYPE="ext2" # blkid /dev/sda6 /dev/sda6: UUID="af7b9ede-fa53-c0c1-74be-31ec752c5cd5" TYPE="linux_raid_member" # blkid /dev/md2 /dev/md2: UUID="a0602d42-6855-482f-870c-6f6ecdcdae3f" TYPE="ext4" Finally, I have my grub2 menuentry setup as follows: ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-25-server' --class ubuntu --class gnu-linux --class gnu --class os { insmod ext2 insmod raid insmod mdraid set root='(hd0,1)' search --no-floppy --fs-uuid --set b25dd301-41b9-4f4d-9b0a-0e31713dd74c linux /vmlinuz-2.6.32-25-server root=UUID=a0602d42-6855-482f-870c-6f6ecdcdae3f ro nosplash noplymouth initrd /initrd.img-2.6.32-25-server } When I attempt to boot, grub loads OK, however I eventually get the following error message: Gave up waiting for root device. ALERT /dev/disk/by-uuid/a0602d42-6855-482f-870c-6f6ecdcdae3f does not exist. Dropping to a shell! If from the grub bootloader I open a grub command line, I can ls (hd0,) and it lists the correct partitions with the UUIDs as shown above - sda6 shows 'a0602d42-6855-482f-870c-6f6ecdcdae3f' (the RAID UUID). If I ls (md2)/ it properly lists all the files on the RAID1 filesystem (ext4) so it doesn't appear to be an issue accessing the raid device. Does anyone have any suggestions as to what the problem might be? I can't figure this one out.

  Read the article

• OS X superuser folders automatically created. Perusers launchd process appears to kill 501

  - by Ric Pen

  New Apple laptop OSX 10.8.2. I have used OS X but many years previously, and am not familiar with subtleties or changes in com.apple.launchd.peruser.x... I have previously (and in retrospect, foolishly) made changes to these rapidly spawned new peruser accounts (my initial reaction was that if ipfw was disabled, then I might well be under hacker attack, which I have dealt with, years ago), but I believe I was wrong, and the results of my efforts at preserving the system's integrity have in fact been destructive, overreactive, and have resulted in much work to restore. My understanding from other posts is that superuser protocols have changed quite dramatically since I bought the first developer version of OS X many years ago. Haven't developed on Apple much since then, w/ exception of WebObjects (IMO, much underrated at that time, and was more user friendly than ASP (prior to .NET, I vaguely recall). Creation of apparently nasty peruser folders appear to confound 501 process, which logs inability to find firewall (ipfw). Can someone help me with this? I am concerned that either the system is improperly configured, an application was improperly installed (although there is little here beyond Apple's SDK, which I find quite accommodating and intuitive). Still, I am a novice, only sporadically develop at this time, and would really just like to see this system running happily. Please offer assistance, in the form of potential info sources, or if you have had a similar experience, then perhaps scripts to suss out this issue. I do not wish to damage the system, but Apple's Developer connection and discussion threads do not appear to have dealt with this particular issue recently... Although I may well have missed something you have not - please apprise. Any assistance on this issue is very much appreciated - by an old guy, who wants to do some things which were fun about 20 years ago.

  Read the article

• How to get rid of "Maxback Engine" for good?

  - by Jonik

  I used to have a Maxtor Shared Storage II network drive; it broke down long ago already. (Later I tried to recover some data from it, and partially succeeded, but haven't yet fully documented it on that question.) Anyway, I just noticed there are still some lingering bits remaining of the (thourougly crappy) software that came with the Maxtor device: a background process called "MaxBack Engine". I googled around a bit and found something related but not very useful: http://www.straitmac.com/jforum/posts/list/600.page http://discussions.apple.com/thread.jspa?threadID=725692 Under /Applications I found "Maxtor EasyManage.app" which I used to use for controlling the drive, and showed it some "rm -rf". Before deleting, I noted that the bundle did contain "MaxBack Engine.app" under Content/Resources. But still, after reboot, the "MaxBack Engine" process is back. I did notice though that it only appears when logging in with my usual user account; with another account it wasn't launched. So, dear Mac gurus, what could I do about this pest? I guess I could fall back to some Unix hackery and write a cronjob that kills any process with that name, but obviously it'd be nicer to be able to clean up from my computer everything left behind by Maxtor's piece of software.

  Read the article

• ksh Auto-Completion PuTTY Configuration

  - by Nitrodist

  I'm having a bit of a problem configuring my PuTTY client to work with the auto-completion feature in the ksh shell. I do a listing on the root with the directories /home and /homeroot and it returns the directories in a list just fine. I can't select it, though, by hitting X = (where X is the number). /home/nitrodist>ls /h #hits esc + = 1) home/ 2) homeroot/ #hits 2 + = for the 'homeroot' dir 1) home/ 2) homeroot/ #hits just the '=' key. 1) home/ 2) homeroot/ Any ideas? I've su -'d to another user who can actually do it with their PuTTY session and I can't do it there, which makes me think it's a PuTTY configuration issue. This is running on a ksh93 shell on HP-UX, if that makes any difference. Here's my ksh config: /home/campbelm>set -o Current option settings allexport off bgnice on emacs off errexit off gmacs off ignoreeof off interactive on keyword off markdirs off monitor on noexec off noclobber off noglob off nolog off notify off nounset off privileged off restricted off trackall off verbose off vi on viraw on xtrace off /home/campbelm>

  Read the article

• Need a place to store a few bytes of meta information on storage media

  - by Jason C

  I'm working on an embedded project. I need a place to store some filesystem-independent meta information on a storage device. The device has an MSDOS partition table. The device also may have unallocated space (depending on its size) but it will be TRIMmed (and also may be blown away by new partitions in the future). I need a location on the device that is not unallocated and that has a low risk of being touched (outside of completely erasing the device). The device is only guaranteed to have an MBR at the point the meta data needs to first be written; meaning there are no EBRs/VBRs present that I could use. There are 446 bytes at the very start of the device available for MBR bootstrap code. Currently my only idea is to store data at the end of this block. However, the device is bootable and I have no way of knowing if I'd be blowing away bootstrap code or not. The sector size is 512 bytes and the MBR is the first sector, I'm pretty sure (correct me if I'm wrong) that that means the second sector is available for use by partition data, so I can't use that either. Does anybody have any ideas? I need 4 bytes of space.

  Read the article

< Previous Page | 594 595 596 597 598 599 600 601 602 603 604 605  | Next Page >