Search Results

Search found 17749 results on 710 pages for 'connection pool'.

Page 612/710 | < Previous Page | 608 609 610 611 612 613 614 615 616 617 618 619  | Next Page >

• Primary/secondary ethernet interfaces in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local...

  Read the article

• (Win7) Gets stuck with ~1% CPU. Especially with multithreading

  - by meow

  Windows 7 32 bit, up to date, Intel i7 860. (For some reason the company runs 32bit Windows everywhere.) I tried to update all motherboard drivers etc. as far as possible. I have a performance issue with a machine which appears in connection with multithreading (or so I think). As an example (and where I most often see it, but it appears on other programs as well): ProteoWizard is a file conversion tool for mass spectrometry files. I can add a list of files and it will attempt to process up to 8 files in parallel (quadcore x 2 threads/core). If I choose 1 to 6 files, I start the process and it goes straight through. If I have =7 files in the queue, conversion goes to ~20%, then gets stuck for 15 seconds, then continues again, always in "chunks" of a few % before getting stuck again. During the time the process is stuck, CPU is at 1%. RAM is not limiting, it is maybe at 70% or so and not going up. I don't get the same problem on other, even slower machines. The computer gets also stuck at 1% CPU doing nothing on other occasions, but for multithreading it is most frequent. Where should I look for the problem?

  Read the article

• VirtualBox with Ubuntu Server guest can't ping outside

  - by Danidan

  Here's my situation: an Ubuntu 12.04 Host running VirtualBox; two guest VMs running Ubuntu Server 12.04 home network, so my Host pc has a wireless connection to the router of my ISP. My problem is in one of the virtual machines: it has 3 NICs, one in NAT mode and the others in Host Only mode. My purpose is to use eth0 (NAT) for Internet access and eth1, eth2 (Host Only) for management of internal virtual network (eth1 uses a VBoxNet with this IP 192.168.69.254). Whenever I try to $ping 8.8.8.8 I get Destination Host Unreachable. While if I $ping 192.168.69.10, that is the IP of the other VM, it works. I can't also ping my Host nor my router My /etc/network/interfaces file is: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 192.168.69.1 netmask 255.255.255.0 auto eth2 iface ifconfig $IFACE 0.0.0.0 up up ip link set $IFACE promisc on down ip link set $IFASE promisc off down ifconfig $IFACE down $route -n returns: Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.2.2 0.0.0.0 UG 100 0 0 eth0 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.69.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Forgetting for now what eth2 needs to do and its setup, why I can't go outside the Host box? What can I do to help you helping me? :-)

  Read the article

• Random "not accessible" "you might not have permission to use this network resource"

  - by Jim Fred

  A couple of computers, both Win7-64 can connect to shares on a NAS server, at least most of the time. At random intervals, these Win7-64 computers cannot access some shares but can access others on the same NAS. When access is denied, a dialog box appears saying "\\myServer\MyShare02 not accessible...you might not have permission to use this network resource..." Other shares, say \\myServer\MyShare01, ARE accessible from the affected computers and yet other computers CAN access the affected shares. Reboots of the affected computers seem to allow the affected computer to connect to the affected shares - but then, getting a cup of coffee seems to help too. When the problem appears, the network seems to be ok e.g. the affected computers can access other shares on the affected server and can ping etc. Also Other computers can access the affected shares. The NAS server is a NetGear ReadyNas Pro. The problem might be on the NAS side such as a resource limitation but since only 2 Win7-64 PCs seem to be affected the most, the problem could be on the PC side - I'm not sure yet. I of course searched for solutions and found several tips addressing initial connection problems (use correct workgroup name, use IP address instead of server name, remove security restrictions etc) but none of those remedies address the random nature of this problem.

  Read the article

• Can't Connect SQL server - process being used by another process. Conflict with IIS?

  - by shinya

  I'm having problem connecting to MS SQL Server (2012 Express) after accessing a database through IIS (web site). I can access the data through web site no problem, but I can't access the data from any other programs (i.e SSMS) until I reboot the SQL server. It seems that the connection stays open even if I close a browser. Here is error message I'm getting Unable to open the physical file "C:---------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Unable to open the physical file "C:-------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Cannot open user default database. Login failed. Login failed for user 'Myserver\myname'. (.Net SqlClient Data Provider) Server Name: MYPC\SQLEXPRESS Error Number: 5120 Severity: 16 State: 101 Line Number: 65536 I follow the help link and it told me to move TCP before named pipes in the protocol order list. I tried it but it didn't help at all. What is the proper settings on SQL server or IIS in order to release process after closing a browser. How do I avoid getting this error? Thank you for your help

  Read the article

• Mysql server high trafic makes websites really slow or unable to load

  - by Holapress

  Lately we have been having a lot of problems with our mysql server, from websites being really slow or even unable to load them at all. The server is a dedicated server that only runs our mysql database. i have been running some test using a profiler (JetProfiler) and tool to stress test (loadUI). If I use loadUI to connect with 50 simultaneous connections to one of our websites that runs a resently big query it will already make the website be unable to load. One of the things that makes me worried is that when I look at Jetprofile it always shows a Treads_connected of 1.00 and it seems that when it hits around 2.00 that I'm unable to connect. The 3 big peaks are when I run a test with loadUI, first one was 15 simultaneous connections wich made it still able for me to load the website but just really slow, the second one was 40 simultaneous connections which already made it impossible to load and the third one was with 100 connection which also didn't make it load anymore. Another thing that worries me is that in JetProfiler it says all the queries that get used are full table scans, could this maybe be the problem? The website I run as a test runs 3 queries, one for a menu that outputs around 1000 rows, one for the adds that has around 560 rows and a big one to get posts that has around 7000 rows (see screenshot bellow) I also have monitored the cpu of the server and there seems to be no problem there, even when I make a lot of connections with loadui the cpu stays low. I can't seem to figure out what is the main cause of the websites being unable to load when there is a high amount of traffic, if anyone has other suggestions for testing or something that might cause the problem please let me know.

  Read the article

• Small maximum number of connections on a Linux router

  - by Eugene

  I have a Linux box acting as a router with no iptables or other firewall and no networking applications running on it, just pure router. I've put it in a test environment that generates many TCP connections, each having unique source and destination IP, and those connections go through this router. I'm observing that number of connections successfully created rise to approximately 500 and then no more connections can be created for several minutes, then another 100 connections can be created and there is another pause, and so on. If 10 connections for each source-destination pair are created, then maximum numbers go about 10 times up, so the problem is probably with many connections from different IPs. As traffic is simply routed, it doesn't have to do with number of file descriptors, iptables connection tracking and other things often proposed to check in similar cases. The box has plenty of free RAM and CPU, both NICs are gigabit. The kernel is 2.6.32. I've already tried increasing net.core.*mem_max, net.core.netdev_max_backlog and txqueuelen on both NICs, with completely no effect. What else should I check ? Is there some rate-limit in the kernel itself ?

  Read the article

• how to get ip address of a PPP(Point-to-Point Protocol) network interface?

  - by Xsmael

  I have a Linux machine with two network interfaces, and I'd like to get the IP address of the PPP interface w1g1 but it doesn't show up in ifconfig. There is a public IP on the PPP interface, but there is no internet connection, I'm trying to troubleshoot but I need to get the IP address of the interface and I can't. ifconfig : eth0 Link encap:Ethernet HWaddr 00:30:48:8D:F0:2C inet addr:192.168.2.254 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe8d:f02c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9970 errors:0 dropped:567 overruns:0 frame:0 TX packets:4338 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1441024 (1.3 MiB) TX bytes:915814 (894.3 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:675 errors:0 dropped:0 overruns:0 frame:0 TX packets:675 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50659 (49.4 KiB) TX bytes:50659 (49.4 KiB) w1g1 Link encap:Point-to-Point Protocol UP POINTOPOINT RUNNING NOARP MTU:240 Metric:1 RX packets:748994 errors:0 dropped:0 overruns:0 frame:0 TX packets:748992 errors:0 dropped:0 overruns:0 carrier:3 collisions:0 txqueuelen:100 RX bytes:179758560 (171.4 MiB) TX bytes:179758080 (171.4 MiB) Interrupt:177 Memory:f881c400-f881e3ff w1g1 is connected to a modem by an RJ45<-Serial cable and the modem is connected to the phone line. The modem is a NOKIA DNT2Mi you can see it here Routing table : 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 169.254.0.0/16 dev eth0 scope link default via 192.168.2.180 dev eth0

  Read the article

• Splitting an HTTP request into multiple byte-range requests

  - by redpola

  I have arrived at the unusual situation of having two completely independent Internet connections to my home. This has the advantage of redundancy etc but the drawback that both connections max out at about 6Mb/s. So one individual outbound http request is directed by my "intelligent gateway" (TP-LINK ER6120) out over one or the other connection for its lifetime. This works fine over complex web pages and utilises both external connects fine. However, single-http-request downloads are limited to the maximum rate of one of the two connections. So I'm thinking, surely I can setup some kind of proxy server to direct all my http requests to. For each incoming http request, the proxy server will issue multiple byte-range requests for the desired data and manage the reassembly and delivery of that data to the client's request. I can see this has some overhead, and also some edge cases where there will be blocking problems waiting for data. I also imagine webmasters of single-servers would rather I didn't hit them with 8 byte-range requests instead of one request. How can I achieve this http request deconstruct/reconstruction? Or am I just barking mad?

  Read the article

• How to troubleshoot Linksys E4200 Remote Management

  - by Jordan

  My Linksys E4200 is configured for Remote Management, but the router is not accepting the connections. Here's the configuration under Administration Management Remote Management Access: Remote Management: Enabled Access via: HTTP Remote Upgrade: Disabled Allowed Remote IP Address: Any IP Address Remote Management Port: 8080 The router is setup to use 192.168.10.41 as its static Internet IP address, and 192.168.35.1 as its LAN IP address. I can access the router just fine via its LAN IP address, but I can't make a connection using http://192.168.10.41:8080. I've tried variations of the settings above (enabled HTTPS, enabled Remote Upgrade, set an IP range of 192.168.10.1-254) but nothing has worked yet. Hoping someone can at least point me in the right direction. Thanks. Update: To clarify, I have a wired router that connects straight to the T1 modem. It's configured to use 192.168.10.1-254 as its internal LAN range. The E4200 wireless router in question is on that LAN using 192.168.10.41 as its WAN IP address. The E4200's internal LAN range is 192.168.35.1-254. I'm not trying to access the E4200 from the Internet, I'm just trying to access it from its WAN IP address. Thanks.

  Read the article

• Sharepoint: authenticating users via forms authentication

  - by sbee

  My problem is the following(sharepoint Newbie) , i want to change the default zone from being a Windows Authenticated Zone to a Forms Authenticated Zone ,thereby forcing the site collection administrator to log in via forms authentication and not windows also the sharepoint users will be accesing the site internally my goal is to effectively replace windows authentication with forms authentication as my company does not have active directory installed. So far i have created an ASP Application that adds the users to the database,the database was created via the .Net Framework Asp tool(Asp reg_sql),however when i change the default zone to the AspNetSqlMembershipProvider(Forms) and attempt to add my site collection administrator via the Central admistrator, i get the following error "No Exact Match found" as shown on the screenshot. My inkling is that somehow the people picker is failing to read the users from the database but reasearch on correcting that thus far has proved fruitless. I have made all the relevant changes on the these sites(Central admin site,My test site & Add Users site) config files.Changes are the following(Membeship Provider,Connection String,People Picker) i left out the role provider for now as it is optional. Help on this would ge highly appreciated...

  Read the article

• pfSense routing between two routers with shared network

  - by JohnCC

  I have a network set-up using two pfSense routers arranged like this:- DMZ1 WAN1 WAN2 DMZ2 | | | | | | | | \___ PF1 PF2___/ | | | | \___TRUSTED___/ Each pfSense router has its own separate WAN connection, and a separate DMZ network attached to it. They share a common TRUSTED LAN between them. The machines on the trusted network have PF1 as their default gateway. PF1 has a static route defined to DMZ2 via PF2, and PF2 has a static route to DMZ1 via PF1. There is NAT to the WAN but internal networks (DMZ1/2 and TRUSTED) use different RFC1918 subnets. I inherited this arrangement, and all used to work fine. I made a config change to PF1 (relating to multicast), and machines on DMZ2 suddenly could not talk to TRUSTED. I rolled the change back, but the problem persisted. What I guess you'd hope would happen is that TCP packets would go DMZ2 - PF2 - TRUSTED and on return TRUSTED - PF1 - PF2 - DMZ2. That's the only way I can see it would have worked. However, PF1 drops the returning packets. I've verified this using tcpdump. I've worked around this by adding static routes to DMZ2 via PF2 to the servers on TRUSTED, but some devices on there do not support static routes so this is not ideal. Is there way to make this arrangement work decently, or is the design inherently flawed? Thanks!

  Read the article

• USB-to-Serial showing gibberish at 115200 Baud

  - by Mose

  I've got a serious problem which drives me crazy because I tried everything I could think of. First of all, I made a video: http://youtu.be/boghkuq7L_s but please read the following text for more information, not only view the video! When using a USB-to-Serial interface everything works as long as I don't go beyond 57600 Baud. At higher rates I only get giberish like this: év.­b0JNLYÆÿ¿iëd0U²(kßÞb! ú]/xscB!ï¯!BoXûÿ1ïâÖCÿ6ÌAnè*íÌC)º¿BíÞØ.C.@ÆÃwHJÂs "YE:ñ.èFðÌCÊ÷ÞÄ !x H w6@BtbHJ ̪ Ì6ì H¾a¿bH.">îvy®;f<ßBÌ p­L¨fæH­E ­þ¼MBÞI What makes the problem so strange is, I exchanged every component and the problem still presists. I tried differtent OSes (Ubuntu, WinXP, Win7, OSX 10.7) with 32 and 64 Bit. I tried USB-to-Serial interface from FTDI and Prolific. I tried reading the output from my Raspberry PI and from an Asterisk Appliance. I changed the cables and the wiring. Nothing helped. In the video I made a example with a old Notebook with native COM and put the USB-to-Serial to the same connection as "sniffer" (only Rx and GND connected) to make sure the output and everything is ok as one can see on the native port. The voltage is ok. Settings for both are 115200 Baud, 8 Bit with 1 Stop and no flow control. Native is ok. USB is messed up. I used the newest drivers and double checked all connections. I have no idea what is wrong here. As I couldn't find anyone describing problems like this I question my long experiance in computer science and think I'm doing some completly wrong... Please help :-/

  Read the article

• iptables drops some packets on port 80 and i don't know the cause.

  - by Janning

  Hi, We are running a firewall with iptables on our Debian Lenny system. I show you only the relevant entries of our firewall. Chain INPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW Chain OUTPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Some packets get dropped each day with log messages like this: Feb 5 15:11:02 host1 kernel: [104332.409003] dropped IN= OUT=eth0 SRC= DST= LEN=1420 TOS=0x00 PREC=0x00 TTL=64 ID=18576 DF PROTO=TCP SPT=80 DPT=59327 WINDOW=54 RES=0x00 ACK URGP=0 for privacy reasons I replaced IP Addresses with and This is no reason for any concern, but I just want to understand what's happening. The web server tries to send a packet to the client, but the firewall somehow came to the conclusion that this packet is "UNRELATED" to any prior traffic. I have set a kernel parameter ip_conntrack_ma to a high enough value to be sure to get all connections tracked by iptables state module: sysctl -w net.ipv4.netfilter.ip_conntrack_max=524288 What's funny about that is I get one connection drop every 20 minutes: 06:34:54 droppedIN= 06:52:10 droppedIN= 07:10:48 droppedIN= 07:30:55 droppedIN= 07:51:29 droppedIN= 08:10:47 droppedIN= 08:31:00 droppedIN= 08:50:52 droppedIN= 09:10:50 droppedIN= 09:30:52 droppedIN= 09:50:49 droppedIN= 10:11:00 droppedIN= 10:30:50 droppedIN= 10:50:56 droppedIN= 11:10:53 droppedIN= 11:31:00 droppedIN= 11:50:49 droppedIN= 12:10:49 droppedIN= 12:30:50 droppedIN= 12:50:51 droppedIN= 13:10:49 droppedIN= 13:30:57 droppedIN= 13:51:01 droppedIN= 14:11:12 droppedIN= 14:31:32 droppedIN= 14:50:59 droppedIN= 15:11:02 droppedIN= That's from today, but on other days it looks like this, too (sometimes the rate varies). What might be the reason? Any help is greatly appreciated. kind regards Janning

  Read the article

• Find which files an apache process is writing to?

  - by Haluk

  We have this apache process which becomes io-bound time to time. Using atop, we can see it is a write operation. Using lsof -p <PID> we can see a list of files open by the httpd process. First we thought "log" files must be the problem. So we turned them off just to test. However write operations still continues. We will continue testing a few other things. For instance we use php session variables a lot. Maybe php session files are getting all the writing. But is there a way to quickly identify files which get written to by the httpd process? This way we can focus our efforts on those files. UPDATE: We used the strace command as suggested. Here are two lines from the output. write(23, "\27\0\0\0\3SET CHARACTER SET utf8", 27) = 27 write(23, "\17\0\0\0\3SET NAMES utf8", 19) = 19 We do not have a mysql process on this server. So is strace also showing what is being written to an ethernet port? UPDATE2: During high io load, the process which consumes most of the write resources gives the following output to strace -e trace=write -p <PID>: --- SIGCHLD (Child exited) @ 0 (0) --- write(9, "!", 1) = 1 write(19, "OPTIONS * HTTP/1.0\r\nUser-Agent: Apache (internal dummy connection)\r\n\r\n", 70) = 70 However I cannot figure out where these are being written to.

  Read the article

• Virtual box host-only adapter configuration

  - by Xoundboy

  I have VirtualBox 4 running on Win 7 with a Centos 6 guest VM set up for hosting my dev server. When I'm connected to my home network the guest can be accessed via a static IP address that I configured (192.168.56.2), but not when I'm in the office. I'm guessing that the DHCP server in the office doesn't have a gateway configured for the 192.168.56.x IP range. I read something about the VB host-only adapter that should allow me to set this guest VM up in such a way that I don't need to be on any network to be able to access the guest from the host using a static IP. I've not been able to find out exactly how to configure this though. Can anyone give me an example configuration, thanks. UPDATE: Thanks for your responses. I've now set up a single virtual network adapter in VirtualBox and set it to host-only: C:\Users\Ben>vboxmanage list hostonlyifs Name: VirtualBox Host-Only Ethernet Adapter GUID: d419ef62-3c46-4525-ad2d-be506c90459a Dhcp: Disabled IPAddress: 192.168.56.2 NetworkMask: 255.255.255.0 IPV6Address: fe80:0000:0000:0000:78e3:b200:5af3:2a57 IPV6NetworkMaskPrefixLength: 64 HardwareAddress: 08:00:27:00:94:e8 MediumType: Ethernet Status: Up VBoxNetworkName: HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter On the guest I've set up eth0 to use the same IP address as the host-only adapter (192.168.56.2) but when I try to log in using Putty I still get "Network Error : connection refused". VirtualBox DHCP servier is enabled but I can't ping the gateway (192.168.56.1) from either host nor guest. There's no firewall running on either OS. What next?

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• openvpn in a bridge?

  - by sebelk

  I have a somewhat tricky proble to solve. We have a wireless link between 2 building. One of them has an mikrotik and below there are some vlans. Some machines of one vlan need to use openvpn to connect to a remote private lan. I put a TP-Link WR1043ND (which those machines connect to) with openwrt with ebtables just in case I need it. I've configured openwrt in such a way that all ports belongs to the same vlan. My idea was to make things as transparent as I can. It has a bridge as follows: usr/sbin/brctl-full show br-lan bridge name bridge id STP enabled interfaces br-lan 8000.f8d111565716 no eth0.1 eth0.2 Also I've added an ebtables rule: ebtables -t broute -A BROUTING -p ipv4 -j DROP So "bridge" has only one IP address. I've installed openvpn and I'm trying to bring up the tunnel but I can't still get working. Sure, someone can says why don't you use the vpn on the mikrotik, there are some reasons, the first one is I have little experience with mikrotik and I'd want to have the vpn at hand :) The problem is that openvpn is not working, because it is complaining that I have only one Ip Address on the server side. So I set up and alias interface with another IP address but is not working either: : Rejected connection attempt from IP-Client-Side:37801 due to --remote setting Is there a way to make it work?

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

• Use both OpenVPN & eth0 together

  - by shadyabhi

  I connect to a VPN using openVPN. Now, after the connection is established, all my traffic goes through tun0. My LAN gateway is 10.100.98.4... So, for apps to use my direct internet connnection I did sudo route add default gw 10.100.98.4 But, I cant use tun0 now. I know this because curl --interface tun0 google.com doesnt give me anything.. How do I go about using both connections simultaneously. How can I achieve that? ROUTING TABLES:- Without VPN running:- Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 With VPN:- Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.0.1 10.10.54.230 255.255.255.255 UGH 0 0 0 tun0 10.10.54.230 * 255.255.255.255 UH 0 0 0 tun0 free-vpn.torvpn 10.100.98.4 255.255.255.255 UGH 0 0 0 eth0 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.10.54.230 0.0.0.0 UG 0 0 0 tun0 After the route command- Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.0.1 10.10.54.230 255.255.255.255 UGH 0 0 0 tun0 10.10.54.230 * 255.255.255.255 UH 0 0 0 tun0 free-vpn.torvpn 10.100.98.4 255.255.255.255 UGH 0 0 0 eth0 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 default 10.10.54.230 0.0.0.0 UG 0 0 0 tun0

  Read the article

• Windows Share permissions

  - by Armando

  I have a SQL/File server that I am replicating a File Share and SQL instance, using ArcServer RHA, to a Replica server. Everything seems to work as far as the replication of the SLQ instance and Share is concerned. When I fail over to the Replica server the DNS Host A record is modified to point to the Replica Server IP Address so if I do an NSLOOKUP on ServerA it then points to the IP Address of ServerB. Ans since the SQL instance is named the same I can still map my ODBC connections to ServerA and I can still make a SQL connection. When I try to do a \ServerA\Share I get an error that says I do not have permissions to the Share. I think this is because it uses keberose authentication and the Share is tied to the actual sever host name. I have tried puting in a CNAME and pointing it to ServerA and Disabling Strict Name Checking on ServerB as well as adding the CNAME to the OptionalNames in the registry but I am still getting the error when I have the ServerA powered off. Is there a way to reset the Authentication of the Share to use the DNS Cname?

  Read the article

• Stack Managed Switches over a distance

  - by Joel Coel

  We have several buildings with stacked switches, where the distance between the stacked units is considerable... separate floors, or at opposite ends of a hallway. They are 3Com switches that stack using cat6 cabling. These switches are coming up on 12 years old now, and as I look around at replacements it seems no one supports this scenario any more. Stacking switches want to use fiber links (it more for me to run and terminate the fiber stacking cables than to purchase the switch) or other custom cables that seem only intended to jump up to the next unit in a rack. What have others done to support stacking over a distance? I'm considering breaking up the stacked switches into separate managed entities and just bridging from the root switch in the buildings, but I'd really like to avoid that for what I hope are obvious reason. The closest thing I've found are from netgear that use hdmi cables for the stacking connection... I could try to support that by running an additional cat6 line and re-terminating both links into a single hdmi port, but I have concerns over that approach as well.

  Read the article

• Postgresql Data Aggregation over WAN Securely

  - by Zach

  Hey guys, Need some advice on how to proceed with this situation: My current scenario is that I have several postgresql (50+) boxes deployed throughout various locations and data centers and a beefy postgresql box setup at a homebase location. All of the deployed boxes have identical database layouts. I'm looking for a solution that would allow for a few things. I realize some of these options overlap and some might only contain mutually exclusive solutions. However, I'm interested to hear your thoughts :) Remotely query the deployed boxes and pull the results back to the homebase box for processing. Nightly (remote) "sync" or dump the deployed boxes' databases to a master database on the homebase box. Remotely push a table entry to all of the deployed boxes from the homebase box. Ensure security of data in transit, and remotely deployed boxes. Up to this point I've been floating on a homebrew multithreaded python/perl system that SSH's into these boxes remotely, which are ACL'ed off to the homebase server and pulls (or pushes) the raw query results over the ssh connection. I have even touched #2 (remote syncing) as I know that would get nasty really quick. I'm interested in any ideas for a more elegant solution that can scale up and stick to my FreeBSD/Linux environment.

  Read the article

• iptables: How to combine DNAT and SNAT to use a secondary IP address?

  - by Que_273

  There are lots of questions on here about iptables DNAT/SNAT setups but I haven't found one that solves my current problem. I have services bound to the IP address of eth0 (e.g. 192.168.0.20) and I also have a IP address on eth0:0 (192.168.0.40) which is shared with another server. Only one server is active, so this alias interface comes and goes depending on which server is active. In order to get traffic accepted by the service a DNAT rule is used to change the destination IP. iptables -t nat -A PREROUTING -d 192.168.0.40 -p udp --dport 7100 -j DNAT --to-destination 192.168.0.20 I also wish all outbound traffic from this service to appear to come from the shared IP, so that return responses will work in the event of a active-standby failover. iptables -t nat -A POSTROUTING -p udp --sport 7100 -j SNAT --to-source 192.168.0.40 My problem is that the SNAT rule is not always run. Inbound traffic causes a connection tracking entry like this. [root]# conntrack -L -p udp udp 17 170 src=192.168.0.185 dst=192.168.0.40 sport=7100 dport=7100 src=192.168.0.20 dst=192.168.0.185 sport=7100 dport=7100 [ASSURED] mark=0 secmark=0 use=2 which means the POSTROUTING chain is not run and outbound traffic leaves with the real IP address as the source. I am thinking I can set up a NOTRACK rule in the raw table to prevent conntracking for this port number, but is there a better or more efficient way to make this work? Edit - Alternative question: Is there a way (in CentOS/Linux) to have an interface that can be bound to but not used, such that it can be attached to the network or detached when a shared IP address is swapped between servers?

  Read the article

• System With Two Network Adapters [closed]

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

< Previous Page | 608 609 610 611 612 613 614 615 616 617 618 619  | Next Page >