Search Results

Search found 47655 results on 1907 pages for 'system restore'.

Page 625/1907 | < Previous Page | 621 622 623 624 625 626 627 628 629 630 631 632  | Next Page >

• How do I prevent libvirt from adding iptables rules for guest NAT networks?

  - by Jack Douglas

  Similar to this old request on BugZilla for Fedora 8, I'm hoping something has changed since then or someone knows another way. I want to manage the iptables rules by hand—the one-size-fits-all automatic rules don't suit me at all. These rules seem to be added and removed when a network is started and destroyed. Is there a way of either preventing these rules being added at all or hooking a script into the network start that restores the default rules afterwards. For now, I'm using a very crude method with cron, but I hope there is a better way: * * * * * root iptables-restore < /etc/sysconfig/iptables

  Read the article

• Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

  - by Pro Backup

  In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

  Read the article

• need recommendation for running PHP/Zend based optimizer

  - by senorsmile

  Firstly, I must admit that I don't know much about setting up PHP beyond the basics. I have an Ubuntu 10.04 server system (hosted) running primarily as an FTP store for a commercial store software. The server that the commercial store is installed on is unfortunately not very reliable, and would like to move that to this Ubuntu 10.04 server. (We've already received permission from the store vendor to do this.) My problem is that they use Zend optimizer which is only compatible with PHP 5.2. I have tried a couple of "hacks" to downgrade PHP to 5.2, but it breaks so many other things that it doesn't seem worth it. My idea is to install some sort of container of Ubuntu 8.04 (like OpenVZ) on the server to house a native install of PHP 5.2 to meet the dependency of the store software. However, it appears that OpenVZ is no longer supported on Ubuntu. Is there another solution similar that I could run on a hosted server to installed a separate "container-like" 8.04 system?

  Read the article

• Allow users to view Word documents only and not be able to edit, copy or save them.

  - by Alexander

  Hello In a traditional Windows Server 2003 environment with AD, we have shared a folder for our policy documents (MS Word). These documents get edited/updated now and then by the administrator(principal of college). Users only have read-only access to the folder, but they can still save-as and then change the content. Sharepoint is a possible solution but not easy to implement. We also thought of using a CMS on Linux and installing Joomla to let users only view the docs with a document management system... but is it possible to automatically retrieve the policy folder on the network and convert or put it in a format that users can only view and not copy? We also thought of saving the docs to secure pdf format but the principal wants an automated system. Basically she just wants to work in Word and the policies must be available to staff members on the network. Any ideas? Much appreciated.

  Read the article

• WCF WebService: Client can't connect, as soon as request client cerficate is activated.

  - by Hinek

  I have an .NET 3.5 WCF WebService hostet in IIS 6 and using a SSL certificate. The communication between client and server works. Then I activate "request client certificate" and the client can't connect anymore Exception: System.ServiceModel.Security.SecurityNegotiationException: Could not establish secure channel for SSL/TLS with authority 'polizei-bv.stadt.hamburg.de'. Inner Exception: System.Net.WebException: The request was aborted: Could not create SSL/TLS secure channel. The certificate, the client uses is in the certificate store (local computer), the root ca is int the trusted root certification authorities store. Where can I check for an explanation on the server side? How can I check if the client really supplies it's certificate (client is not on my side)?

  Read the article

• Option and command keys in OSX are swapped and keyboard preferences do not set them back.

  - by bikesandcode

  On my MacBook pro, I occasionally use external keyboards, generally Windows ones and things have been fine. Yesterday, I plugged in a new one, remapped the command/option keys so the windows/alt keys were in the same configuration, again, nothing new here. However, this time when I unplugged the USB keyboard, the laptops option/command keys remained switched. More annoying is that if I go into the System Preferences - Keyboards - Modifier keys, remapping the keys to actions does not work. I can use the drop downs to disable any specific keys, but switching the behaviours does nothing. (Cmd/Option obvious, tried remapping anything to caps lock and a few other combinations, no joy. Restore defaults set the configuration to what I'd expect, but the settings are evidently ignored.) So: Any ideas?

  Read the article

• Reconnect Attempts for CIFS share

  - by Davin

  I have a CIFS share mounted in the FSTAB on Ubuntu server, which connects to our SAN and works without issue. Last night we had an issue with the SAN for about 12 hours. We corrected the problem and the Windows boxes restored their mappings. The Ubuntu box did not, but we were able to restore with [mount -a]. I saw options to specify retries in man for NFS but not CIFS. Any ideas on ensuring a reconnect if the SAN goes down again?

  Read the article

• redundant/multi-site terminal server

  - by Adam

  Hi We have a Hyper-V cluster running 5 virtual terminal servers using HA. We need to be able make this system redundant and so if this site was to fail our users could log into the backup system at another location and access their data via the terminal servers. Any ideas? We were thinking of maybe using a NAS which replicated the data to the other location in real-time(pass-through disks)? and having a similar Hyper-V cluster setup in the backup location. However we would need to create the users in both location and create a virtual mirror without the data ie applications, directories, settings etc. Is this the best way to achieve this? We have read that using Hyper-v pass through disks is a big performance de-grade.

  Read the article

• Cannot open an external hard drive in Windows

  - by SeeBees

  In Windows 7, I was installing wubi ubuntu to an external hard drive when suddenly it disconnected from the PC. After I connected it back to PC, and double clicked the drive's icon, Windows didn't show the content of the disk but asked me whether I wanted to format it. The hard drive has only one partition. Its format is NTFS. I also connected the disk to Windows XP. It makes the Windows Explorer super slow and I cannot open the disk as well. I can open the disk on Ubuntu and Mac. Is it possible to restore the disk and make it run in Windows? Thanks

  Read the article

• Windows XP Home Edition SP3 cant recognise PCMIA SD Card

  - by Pozo

  System Specifications: Laptop : Dell Inspiron 6000 OS: Windows Home Edition SP3 SD Adapter: Hagiwara Smart Media Adapter I inserted the card into the slot, windows xp recognises the device, lists the pcmia controller on the device manager list, an entry appears under the IDE ATA/ATAPI category on the device manager as well. However, the device does not show under my computer and the driver does not get assigned a letter number. I checked the system logs from the device manager and there were no logged errors. Checking the Hagiwara support website, the manufacturer indicates that the adapter driver is the same as the windows xp pcmia controller. Checking Dell's website, no specific drivers were listed for that either. General Search on the web indicates that multiple people face similar problems with their SD cards, yet none actually spell out the route issue that causes this. Please let me know if you have any suggestions for further debugging. Thanks in advance

  Read the article

• Nvidia Optimus shows Nvidia card is always active in Windows 8

  - by Ty Underwood

  I have loaded the new Asus Nvidia driver for my Asus Ux32VD that I have installed Windows 8 on. It has an Nvidia 620m and Intel hd 4000 integrated graphics. The problem is that the Optimus activity icon in my system tray shows that the Nvidia card is always active, though it shows that it is not doing anything. I can force the system to prefer the Intel graphics, and after rebooting, the Nvidia card will shut off, but then all the programs will be overridden and use the Intel graphics. Is anyone else having problems with Optimus in Windows 8? My battery life is really suffering because I'm always idling my Nvidia card while also presumably running the Intel card. Any suggestions would be appreciated.

  Read the article

• networking fails when DNS servers are specified manualy

  - by Matthew Scouten

  When I let Windows-7 use DHCP to find its own DNS server, everything works fine. Then I use ipconfig to get the IPs of the DNS servers in question, and specify them manually. Now the network stops working. (I need to do this because my next step is to restore the router that is going to lie about the proper DNS server. Don't ask why, it is required by my father's work. The IT there are not exactly on the ball.) Why would this make a difference? It is the same set of servers, just obtained differently.

  Read the article

• Build and migrated to software raid (mdadm) on GPT disk, now can't assemble array

  - by John H

  mdadm, gpt issues, unrecognized partitions. Simplified question: How do I get mdadm to recognize GPT partitions? I have been attempting to convert/copy my Ubuntu 11.10 OS from a single drive to software raid 1. I have done similar in the past, but in this case, I was adding in a drive that has been configured for GPT and I tried to work with that without fully looking into the implications. Currently, I have a non-booting mdadm RAID 1 array of /dev/md127 (the OS assigned that and it keeps picking up). I am booting off of live USB keys, currently System Rescue CD from sysresccd. While gdisk and parted can see all the partitions, most of the OS utilities do not, including mdadm. My main goal is just to make the raid array accessible so I can get pull the data and start fresh (without using GPT). /dev/md127 /dev/sda /dev/sda1 <- GPT type partition /dev/sda1 <- exists within the GPT part, member of md127 /dev/sda2 <- exists within the GPT part, empty /dev/sdb /dev/sdb1 <- GPT type partition /dev/sdb1 <- exists within the GPT part, member of md127 History: POINT A: The original OS was install on sda (actually /dev/sda6). I used a the Ubuntu live usb to add sdb. I got warning from fdisk about GPT so I used gdisk to create a raid partition (sdb1) and mdadm to create a raid1 mirror with a missing drive. I had many issues getting this working (including being unable to get grub to install) but I eventually got it to boot using grub on sda and /dev/md127 off of sdb. So at point A, I had copied my OS from sda6 to md127 on sdb. I then booted into a rescue mode and attempted to get a bootloader onto sdb, which failed. I then discovered my mistake: I had installed the raid onto sdb instead of sdb1, essentially overwriting the sdb1 partition. POINT B: I now had two copies of my data- one on md127/sdb, and one on sda. I destroyed data on sda and created a new GPT table on sda. I then created sda1 for the raid array, and sda2 for a scratch partition. I added sda1 into the raid array and let it rebuild. md127 now covered /dev/sdb and /dev/sda1 as fully active and synced. POINT C: I rebooted onto linux rescue again and was still able to access the raid array. I then removed /dev/sdb from the array and created /dev/sdb1 for the raid. I added sdb1 to the array and let it sync. I was able to mount and access /dev/md127 without issues. Once it completed, both /dev/sda1 and /dev/sdb1 were GPT partitions and actively syncing. POINT D (current): I rebooted again to test if the array would boot and grub failed to load. I booted off of my live thumb drive and found that I can no longer assemble the raid array. mdadm doesn't see the required partitions. -- root@freshdesk /root % uname -a Linux freshdesk 3.0.24-std251-amd64 #2 SMP Sat Mar 17 12:08:55 UTC 2012 x86_64 AMD Athlon(tm) II X4 645 Processor AuthenticAMD GNU/Linux === /proc/partitions and parted look good: root@freshdesk /root % cat /proc/partitions major minor #blocks name 7 0 301788 loop0 8 0 976762584 sda 8 1 732579840 sda1 8 2 244181703 sda2 8 16 732574584 sdb 8 17 732573543 sdb1 8 32 7876607 sdc 8 33 7873349 sdc1 (parted) print all Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 2 750GB 1000GB 250GB Linux/Windows data Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 Linux RAID raid Model: SanDisk SanDisk Cruzer (scsi) Disk /dev/sdc: 8066MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 31.7kB 8062MB 8062MB primary fat32 boot, lba === # no sda2, and I double the sdb1 is the one shown in parted root@freshdesk /root % blkid /dev/loop0: TYPE="squashfs" /dev/sda1: UUID="75dd6c2d-f0a8-4302-9da4-792cc7d72355" TYPE="ext4" /dev/sdc1: LABEL="PENDRIVE" UUID="1102-3720" TYPE="vfat" /dev/sdb1: UUID="2dd89f15-65bb-ff88-e368-bf24bd0fce41" TYPE="linux_raid_member" root@freshdesk /root % mdadm -E /dev/sda1 mdadm: No md superblock detected on /dev/sda1. # this is probably a result of me attempting to force the array up, putting superblocks on the GPT partition root@freshdesk /root % mdadm -E /dev/sdb1 /dev/sdb1: Magic : a92b4efc Version : 0.90.00 UUID : 2dd89f15:65bbff88:e368bf24:bd0fce41 Creation Time : Fri Mar 30 19:25:30 2012 Raid Level : raid1 Used Dev Size : 732568320 (698.63 GiB 750.15 GB) Array Size : 732568320 (698.63 GiB 750.15 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 127 Update Time : Sat Mar 31 12:39:38 2012 State : clean Active Devices : 1 Working Devices : 2 Failed Devices : 1 Spare Devices : 1 Checksum : a7d038b3 - correct Events : 20195 Number Major Minor RaidDevice State this 2 8 17 2 spare /dev/sdb1 0 0 8 1 0 active sync /dev/sda1 1 1 0 0 1 faulty removed 2 2 8 17 2 spare /dev/sdb1 === root@freshdesk /root % mdadm -A /dev/md127 /dev/sda1 /dev/sdb1 mdadm: no recogniseable superblock on /dev/sda1 mdadm: /dev/sda1 has no superblock - assembly aborted root@freshdesk /root % mdadm -A /dev/md127 /dev/sdb1 mdadm: cannot open device /dev/sdb1: Device or resource busy mdadm: /dev/sdb1 has no superblock - assembly aborted

  Read the article

• Applescript Adobe Updater

  - by Alex

  So, I am new to Applescript editor and I am trying to write code to automatically update computers. For some odd reason I can not seem to get Adobe to update successfully. I tried using Accessibility Inspector, but nothing appeared like AXButton So is there even a way of writing code for Adobe when there is not an AXButton option? This is the code: tell application "Adobe Application Manager" activate end tell delay 7.0 tell application "System Events" tell process "Adobe Application Manager" click button "Update" of window "Adobe Application Manager" end tell end tell and this is the error message: error "System Events got an error: Can’t get button \"Update\" of window \"Adobe Application Manager\" of process \"Adobe Application Manager\"." number -1728 from button "Update" of window "Adobe Application Manager" of process "Adobe Application Manager

  Read the article

• How can I install my installed linux on another hardware too?

  - by donamir

  Hi. It's my state: I installed some apps on a linux server(ubuntu). Apps stack are development tools: -some of Atlassian product -SVN, USVN -Maven, Artifactory -Tomcat & ... My problem: I want to create a bootable dvd to be able to restore same state(OS, configuration and apps) on another hardware(server). Some notes: I prefer ubuntu but my linux can be a different distributions if needed. w I prefer final result (bootable dvd) be simple and easy to use as installing a linux(ubuntu). I prefer a bootable DVD but if it's not possible, any other solution like partial backup/package even if needed to install first OS and then apply the package/backup/... can be good. Finally: Thanks in advance.

  Read the article

• How to recover a MySQL InnoDB table?

  - by Kau-Boy

  When I try to launch the Plesk administration page of you server I get the following error: ERROR: PleskMainDBException MySQL query failed: MySQL server has gone away The MySQL Server is working well. Although it seems that the plesk database is somehow corrupt and any action on this database results in a restart of the mysql process, so even queries to other databases on the same MySQL server will be lost. If I try to connect to the plesk database using phpMyAdmin, I can only see the number of tables, the database had originally. But I am not able to open the tables listing. As soon as I try it, the mysql process crashes again. Trying to connect to the database using ssh works. I can even run a SELECT statement against any table an get a result. I don't know if it is an plesk error or an error of the psa database or even the MySQL server. Can you give me any tips on how to recover the plesk system. Should I try to repair the Plesk installation before. And if so, how can I do it and will all my settings get lost doing it? EDIT: Trying to dump the database, I get the following error: mysqldump: Got error: 2013: Lost connection to MySQL server during query when using LOCK TABLES EDIT: I could find out, that the table 'data_bases' is responsible for the crash of the MySQL server process. But trying to repair it using a REPAIR TABLE statement doesn't work. EDIT: I now dropped the whole database and restored it from a dump. But why I try to recover the data_bases table I get the following error: ERROR 1005 (HY000) at line 24: Can't create table './psa/data_bases.frm' (errno: 121) I am not able to create the table again. Somewhere in the MySQL system there is still some information about this table. I tested the same thing locally. If I just delete the table files and then try to create the table again I get the same error. If I drop the table through MySQL, I can create the table again afterwards. But trying to drop the table using MySQL the whole MySQL system crashed. Is there any way to solve that issue?

  Read the article

• Method for imaging a HDD? [closed]

  - by Sonny Ordell

  Possible Duplicate: Imaging new hard drive in Windows 7 laptop? I have to image my 320gb Laptop HDD before I send it in for repairs. The HDD is likely going to get replaced, and I would ideally like to be able to restore everything as I have it now without having to reinstall my OSes, programs and place all my files back again. I can make space on an external HDD I have, so am just looking for how I should go about this. Should I just use dd with a linux rescue cd? Or is there perhaps a more suitable program with its own rescue disk?

  Read the article

• unable to install oracle

  - by Mohamed Saligh

  I have installed oracle few months back. I was running fine in my local system. Unfortunately my friend has removed all the directories in safe mode. meaning to say it was not properly un-installed from my system. I tried to remove all the Registry keys, Services associated with oracle. Now, I can install it. Unable to use any sqlplus services or anything. How to completely remove my hidden old files and services if any. Need to install and use it. Any help indeed

  Read the article

• How to keep time on resumed KVM guest with libvirt?

  - by Hristo Hristov

  On my host I am using libvirt and a KVM guest. When the host is shutting down, libvirt suspends the guest. When the host is starting up, libvirt resumes the guest. The problem is, if the guest is suspended and resumed after 24 hours for example, then the guest time is 24 hours in the past. I thought that maybe the problem is with the clocksource, but it is set to "kvm-clock" already. $ cat /sys/devices/system/clocksource/clocksource0/available_clocksource kvm-clock tsc hpet acpi_pm $ cat /sys/devices/system/clocksource/clocksource0/current_clocksource kvm-clock

  Read the article

• Ubuntu 12.04 full iphone backup

  - by James

  I am using ubuntu 12.04 and have an iPhone 5 using iOS 6.0.2. My question is how can I do a full backup on ubuntu. Most questions I have seen on this are related to peoples music libraries etc how ever this is of little importance to me. What I want to be able to do is a complete (photos,contacts, OS etc) image backup (and restore if required). So far I have looked up libimobiledevice and this seems to be just that a API. Other suggestions are about Rhythmbox for music etc but this is not of huge importance to me. Finally the suggestion is for using Itune and some combination of Wine or Playforlinux. But even if you get iTunes working iPhone access is limited. Surely someone must have the same problem and found a solution. J

  Read the article

• Centralize proxy settings for all the application on my workstation

  - by Leonardo

  As a consultant, I used to work at different clients premises. It happens frequently that most of them has specific proxy settings, but not all the application I have installed on my laptop get settings from system preferences, for allowing me to change settings in one place. Some of them bypass system preferences completely, proposing their own mask for entering specific data such as username, host and password. I am looking for a convenient and not much intrusive way to share a common access point on which I could enter data, and maybe persist them. An 'automatic' switching would be ideal, for example based on some network identification, but there's no problem for me to enter data manually. I am not an IT expert, but to explain myself clearly, I am looking for a solution like .pac file is for browsers. Relevant OS I am using are MacOSX and Linux (Ubuntu).

  Read the article

• Bluetooth radio device is not available

  - by Mike

  I reinstalled my Windows 7 operating system, and have since been unable to detect my Logitech m555b bluetooth mouse. Here is some info about my system: I have have a working connection with a bluetooth printer. I have a message in the "My Bluetooth" section of explorer stating "Bluetooth radio device is not available". The Device Manager indicates that the Generic Bluetooth radio is working correctly. The bluetooth "F12" switch is on. Mouse batteries are new and the right way around. I'm presuming that I need a bluetooth driver which is non generic. The computer is a Clevo P150HMx (the version with the GTX485 GPU) with the default WLAN / bluetooth combo card manufactured by Realtek (I think it's a Realtek RTL8188CE card). I think I have the drivers installed, but I still get the generic driver in the Device Manager. I'm confused. Please help, I'm going mad on the touchpad. (Thanks for the touchup wizlog)

  Read the article

• What happens with the Guest OS's on ESXi in the event of a power failure?

  - by Jeremy Holovacs

  Many small businesses would prefer to let their server drop on power failure than to pay even $100 for a cheap UPS. It's often difficult to convince them of the value of something like that; it's why they like ESXi. It's free, they can save a lot of cash by putting a bunch of linux servers on one machine, and then I get paid. :) If the ESXi server experiences a power outage, it is set to come back on automatically when power is restored. What happens with the guest OS's? Ideally I would like them to all come online again as well, assuming they were on when power was lost, but I see no option for choosing this. I don't want to yank power to the system just to try it out, of course. I'm sure someone knows what happens by default, and perhaps how to make my system to work as I would wish.

  Read the article

• Choosing A Power Supply [closed]

  - by Geeks On Hugs

  Possible Duplicate: Power Supply Capacity Formula How can I check if my system needs more PSU power? I'm not sure if it's OK or not to ask a hardware question here. If not please let me know a good place but I've always got good info here so I thought I'd give it a shot. I'm custom building a new workstation for coding (Linux/Eclipse). How do I determine how much power the power supply needs? I'm building a mini ITX system on a budget and so I need to get as small as possible that is sufficient. I'll have a mini itx mobo with on board wifi and bluetooth, 8 GB RAM, an Intel i3 3.1 Ghz processor, 64 GB SSD and a slim optical drive. In the future I might add a descrete GPU, 16 GB RAM, 128 GB SSD. What is the minimum power I need and how do I calculate that?

  Read the article

• Using e-mail address as user name for SMTP and POP3

  - by PeterMmm

  I have a exim4 setup as SMTP. My user naming schema is to name all mail users for this server as m001, m002, m003, ... and then redirect to a real e-mail address with virtual domains. How can I allow my users to authenticate with exim to send mail using either their system user name (m001) or the email address ([email protected])? User login information for m001 are stored in linux system files (passwd, shadow). They are linked thru entries in a virtual address table for each domain that this server can serve: # /etc/exim4/virtual/example.com m001: [email protected] m002: [email protected] m003: [email protected] The same can be applied to qpopper ?

  Read the article

< Previous Page | 621 622 623 624 625 626 627 628 629 630 631 632  | Next Page >