Search Results

Search found 17847 results on 714 pages for 'virtual disk'.

Page 626/714 | < Previous Page | 622 623 624 625 626 627 628 629 630 631 632 633  | Next Page >

• SRM 4 Test Fails with message for some VM : Error: A specified parameter was not correct.

  - by Setesh

  Here are my architecture : For the protected site 4 Host VSphere Enterprise Plus, each one with 2 HBAs FC connected to the switch fabric, connected to an EMC CX4-120 1 VCenter 1 SRM For the recovery site 2 Hosts Vsphere 4 1 Vcenter 1 SRM 1 CX-4-120 The CX4-120 is connected to the second CX4-120 with ISCSI and the MirrorView / Asynchronous. I synchronise for the time 6 Lun on a FC DAE, 2 on a S-ATA DAE I have allocated 30% of the amount synchronised LUN for the SNAPSHOT us, but I have allocated them only on my S-ATA II DAE. It does not make a problem, my snapshot are correctly active. All the installation is new (hardware and software), installed in January with the last files available in download. I have a strange problem, and it's random, sometimes when I run a test on my RP, some VMs have this error : Error: A specified parameter was not correct. I don't know where to look. Any help is appreciated... PS : I have checked on all the VMs, no Floppy disk or CD attached. PS2 : There is severals VMs with RDM and OCFS2 filesystems on it.

  Read the article

• Mac OS X - Time Machine backup fails verification - What can I do to save the history?

  - by usermac75

  Hi, How do I make Time Machine to make a new complete backup without losing older versions of backed up files? Verbose: I am using the Time Machine backup on my OS X (Snow Leopard) to backup the whole computer to an external drive. I especially like the "history", i.e. the feature that allows you to restore the older version of a file. Problem: I had some data corruption on my external backup drive, I repaired it with the System Tool for doing that, it found some faults. I had the disk tool repair the external drive. After that, the external drive was OK and I could use Time Machine again. I let Time Machine do one more backup. Now I made a verification according to http://superuser.com/questions/47628/verifying-time-machine-backups, namely along sudo diff -qr . $HOME/Desktop 2>&1 | tee $HOME/timemachine-diff.log However: After doing the command above, several differences and missing files were reported, approx. 200 files in sum. Whereas some of the missing files were cache or excluded directories, the differences do bother me, especially as some important documents from me are listed as differing. How can I make sure that the data on the external drive is synced correctly? Is it possible to have Time Machine to do a complete new backup without losing the history? Or to have Time Machine compare all files for differences and re-write all files that are different? Or can I set some flags on the files that do not match to have them copied again? (like the archive-flag in Windows/Dos). I'd rather not touch the files because I would like to keep the date of last change/date of creation) Thank you for your thoughts!

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• Hibernation fails; The system cannot find the file specified

  - by GMMan

  Recently I installed Ubuntu 12.04.1 LTS on my Lenovo Y480. Hibernation was working properly after the Ubuntu install, but I was making sure all of the operating systems on my system worked, including OneKey Recovery (recovery partition). It is of note that I installed Windows 7 from scratch with a disk image I downloaded off of my university's DreamSpark program, and further to that I had to image the partition with Paragon Backup & Recovery, repartition to convert the Windows partition to extended, install Ubuntu, and then restore the image. During that process I also used the Windows disc to edit the BCD as to reuse the existing entry for the restored partition. I also used the automated "repair your computer" option. With verification, I noticed that the "repair your computer" option actually wrote to the wrong BCD (the recovery partition), and I mounted the partition and restored the original BCD (from a copy I made earlier), and rebooted. At this point my GRUB broke, and I was able to restore it. At this point hibernation broke. I tried powercfg /h off and powercfg /h on, rebooted, and nothing. Also tried increasing the hibernation file size as directed on this post, but it still doesn't work. Executing shutdown /h yields The system cannot find the file specified.(2). What file? It seems that mounting the system partition sometimes works, but I don't want to keep it mounted in case it gets written to accidentally. How do I permanently fix this?

  Read the article

• USB drive was bootable, but no longer isn't

  - by i-g

  I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

  Read the article

• Setup shared internet connection on virtualbox with fixed IP

  - by Tom

  I am a web developer and until recently I have been using ubuntu as my OS. For many reasons, I have switched back to windows. I still want to keep my server on linux platform, so I setup my local server as a virtual machine. Everything works great, but i have a little struggle with the networking. Since I am working in different places and going around clients, I connect to all sorts of network with different settings. That means the possible IP range is very dynamic which causes issues when I work on my local server. At the moment I have a dynamic IP on my host and static IP on my guest. That way I can access the server from my host (by adding record to hosts file). I also have internet connection on the guest. But once i change networks, it does not work (assuming the network has different configuration). My question is, how to setup host-guest networking, so no matter what network I connect to, I can keep my static IP on guest, which is registered in hosts file on my host so I can access the webserver and also I will have internet connection on the guest? Hope it make sense. Thank you

  Read the article

• How to make Thunderbird play nice with Google mail

  - by Christi

  Thunderbird and gmail aren't exactly the best of friends. Gmail's tags mean that Thunderbird often downloads multiple copies of a single mail. Anything tagged in gmail will appear in a folder related to that tag, the "all mail" folder, and possibly the "inbox" and "sent mail" folders too. Thus a mail with multiple tags could potentially be stored more than four times in a local Thunderbird cache. This can make searching difficult, and is obviously wasteful of disk space. The best solution I have come up with is as follows. Operate a zero inbox policy (i.e. use the inbox for processing live mail only and archive everything else) which eliminates an extra copy in the inbox. Secondly, configure Thunderbird not to sync the "Sent Mail" folder - this is a bit of a pain, since I actually find it quite useful to be able to look through just the mails I've sent, but a search can duplicate this functionality. In this way, most of the duplicates are removed, and only mail with tags is stored locally more than once. Ideally, however, I'd only like one copy of each mail to be stored locally. I am surprised Thunderbird doesn't store mail by some sort of hashing algorithm to prevent precisely this problem - but it wouldn't be compatible with the way the folders are mirrored in a local directory structure, I suppose. Can anyone think of a better way to get Thunderbird to cache a Google mail account locally efficiently.

  Read the article

• How can I make my Super keys (Windows Key) behave more like Ctrl/Alt/Shift in Linux

  - by deltaray

  After using the Ctrl + "arrow keys" for 13 years to switch virtual desktops in X windows, I've been convinced recently to change to using the Super keys instead (the windows key and the context menu key, which I've remapped). This all works fine for the most part. However, something is still picking up the key events that these keys are sending as if they are a normal alphanumeric like key. For example, I first noticed this in Google Docs spreadsheet that if I press the windows key alone over top of a cell, that it starts editing that cell. It doesn't insert anything, it just sends a key event that Firefox sees and starts editing the cell. This caused problems on a collaborative document I was working on as the way Google docs works, it led to me accidentally erasing the data in a few fields before I realised what was going on. I like using the super keys, but I want them to behave more like a Ctrl or Alt key does in that its a modifier key and doesn't send anything until a second key is pressed. My setup is the following: Ubuntu 10.10 XFCE 4 Microsoft Natural Ergo 4000 keyboard (with the logo scratched out) The following is my .Xmodmap file: remove Lock = Caps_Lock keycode 66 = Escape ! The below maps my other windows context menu key. keycode 135 = Super_R Edit: As requested, here is the relevant output from xev for a keypress and keyrelease of my Super_L (left windows key) KeyPress event, serial 34, synthetic NO, window 0x8200001, root 0x15d, subw 0x0, time 2428849342, (177,174), root:(182,228), state 0x10, keycode 133 (keysym 0xffeb, Super_L), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 34, synthetic NO, window 0x8200001, root 0x15d, subw 0x0, time 2428849430, (177,174), root:(182,228), state 0x50, keycode 133 (keysym 0xffeb, Super_L), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

  Read the article

• Euro character messed up during FTP transfer

  - by djechelon

  My customer is using a very outdated ecommerce management system on my hosting service. For that product, no support is being provided anymore by the vendor. Brief explanation: the shop website, that claims to run under LAMP stack, is built by an old Visual Basic Windows application running on MS Access. The user constructs the shop, defines the HTML template, adds products and categories, etc. Then the VB exe builds the PHP pages (one for each template page) and the SQL script to run on MySQL. It also uploads everything via FTP and runs the installation/upgrade script on its own. The problem Browsing the website, many products' descriptions are cut before the euro sign. For example, what was supposed to be "Product price €1000" becomes "Product price" The analysis MySQL contains a cutted description until the € sign, so it's not PHP fault The Access databases contain full description with € sign, so it's not fault of the webmaster writing bad description or eDisplay cutting them The SQL that will run once the site gets uploaded, stored on my local machine before upload, contains the € sign The same script, after being FTPed by eDisplay and opened with nano from SSH, shows the € sign messed up like this: ^À vsftpd log reports (obfuscated for privacy) Sat Dec 15 11:16:57 2012 22 xxx.xxx.128.13 1112727 /srv/www/domains/xxxxxx.it/htdocs/db.sql b _ i r xxxxxxx ftp 0 * c which seems to be a binary transfer (and also a huge security vulnerability because you can download the whole database from unauthenticated HTTP) The eDisplay internal FTP client provides no option for ascii/binary transfer modes [Add] Trying to manually upload the SQL file via SFTP shows messing up euro [Add2] Trying to manually upload using Xftp client with explicit ASCII mode doesn't fix too It looks like the file gets uploaded as binary. Perhaps on the customer's previous host it all worked fine because that was a Windows host. The server It's an Azure virtual machine running openSUSE 12.2 with both vsftpd and openSSH The question Without asking the customer to manually upload files using FileZilla or replacing € with &euro;, because he refuses, what can I do on server side to prevent vsftpd to screw up euro sign?

  Read the article

• What can inexperienced admin expect after server setup completed seemingly fine? [closed]

  - by Miloshio

  Inexperienced person seems to have done everything fine so far. This is his very first time that he is the only one in charge for LAMP server. He has installed OS, network, Apache, PHP, MySQL, Proftpd, MTA & MDA software, configured VirtualHosts properly (facts because he calls himself admin), done user management and various configuration settings with respect to security recommendations and... everything is fine for now... For now. If you were directing horror movie for server admin above mentioned what would you make up for boogieman that showed up and started to pursue him? Omitting hardware disaster cases for which one cannot do anything 'from remote', what is the most common causes of server or part-of-server or server-related significant failure when managed by inexperienced admin? I have in mind something that is newbie admins very often missing which is leading to later intervention of someone with experience? May that be some uncontrolled CPU-eating leftover process, memory-related glitch, widely-used feature that messes up something unexpected on anything like that? Newbie admin for now only monitors disk-space and RAM usage, and number of running processes. He would appreciate any tips regarding what's probably going to happen to his server over time.

  Read the article

• Apache forwarding to tomcat shows a blank page

  - by MNS

  I have an application running on tomcat at http ://www.example.com:9090/mycontext. The host name in server.xml points to www .example.com. I do not have localhost anymore. I am using apache to forward requests to tomcat using mod_proxy. Things work fine as long as the ProxyPath is /mycontext. The server name setup in virtual host is www .abc.com and http ://www.abc.com/mycontext works fine. However I would like to ignore the context path and simply use http://www.abc.com/ to forward requests to http://www.example.com:9090/mycontext. When I do this, apache shows me a blank page. What am I missing here? I have not changed anything in server.xml except the default host to www .example.com. <VirtualHost *:80> ServerName www.abc.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://www.example.com:9090/mycontext ProxyPassReverse / http://www.example.com:9090/mycontext </VirtualHost> Thanks

  Read the article

• Wordpress on Apache is redirecting all https to http

  - by Krist van Besien

  I have a problem with a wordpress site on a server I admin. I don't know anything about wordpress however. My problem is that we want the site to be accessed over https, bot somehow all requests to https:// URLs are answered by the server with a 302, redirecting to http. The wordpress site itself is configured to use https, and we see that in the pages that are generated the links are all https links. In the apache config there are no rewrite rules and no redirects. However, any request to a https:// URL is answered with a redirect to the equivalent http URL. And I really would like to know where these redirects are coming from, what is generating these redirects. I've increased the loglevel on the webserver to DEBUG, but did not get any info there. I tried to enable debug logging in wordpress per the recipy I found here: http://codex.wordpress.org/Debugging_in_WordPress But did not get a debug.log file in the directory where one should appear. I'm really at a loss here, and need to fix this urgently. Any hints as where to start looking? Apache is 2.2.14 on Ubuntu. There are several other virtual hosts on this server, using php and https without any problem... Edit: I created a small info.php script and dropped that in the webservers' root. Calling this yields the output of the script, no redirect is generated. This suggest that it's not the webserver, but wordpress that is doing it. A second thing I noticed is that the redirect comes with several cookies, one of which has "httponly" set. Could that be it?

  Read the article

• What does SQL Server's BACKUPIO wait type mean?

  - by solublefish

  I'm using Sql Server 2008 ("R1"), with some maintenance plans that back up my databases to a network share. Some of my backup jobs show long waits of type "BACKUPIO". Of course it seems like this is an I/O subsystem limitation, but I'm skeptical. Perfmon stats for I/O on the production (source) server are well within normal trends for that server. The destination server shows a sustained 7MB/s write rate, which seems incredibly low, even for a slow disk. The network link is gigabit ethernet and nowhere near saturated. The few docs I've turned up about BACKUPIO indicate that it's not specifically a wait on I/O, surprisingly enough. This MSFT doc says it's abnormal unless you're using a tape drive, which I'm not. But it doesn't say (or I don't understand) exactly what resource is missing. http://www.docstoc.com/docs/24580659/Performance-Tuning-in-SQL-Server-2005 And this piece says it's not related to I/O performance at all. http://www.informit.com/articles/article.aspx?p=686168&seqNum=5 "Note that BACKUPIO and IO_AUDIT_MUTEX are not related to IO performance." Anyway, does anyone know what BACKUPIO actually means and/or what I can do to diagnose or eliminate it?

  Read the article

• Pull network or power? (for contianing a rooted server)

  - by Aleksandr Levchuk

  When a server gets rooted (e.g. a situation like this), one of the first things that you may decide to do is containment. Some security specialists advise not to enter remediation immediately and to keep the server online until forensics are completed. Those advises are usually for APT. It's different if you have occasional Script kiddie breaches. However, you may decide to remediate (fix things) early and one of the steps in remediation is containment of the server. Quoting from Robert Moir's Answer - "disconnect the victim from its muggers". A server can be contained by pulling the network cable or the power cable. Which method is better? Taking into consideration the need for: Protecting victims from further damage Executing successful forensics (Possibly) Protecting valuable data on the server Edit: 5 assumptions Assuming: You detected early: 24 hours. You want to recover early: 3 days of 1 systems admin on the job (forensics and recovery). The server is not a Virtual Machine or a Container able to take a snapshot capturing the contents of the servers memory. You decide not to attempt prosecuting. You suspect that the attacker may be using some form of software (possibly sophisticated) and this software is still running on the server.

  Read the article

• Windows Vista freezes

  - by Kakurady

  Windows Vista (32-bit) would randomly freeze on my computer, usually 15-30 minutes after login but can happen just after login. All applications would stop responding and the hard drive will not make any sound, and after a while, the mouse cursor will also stop moving. I dual-boot Ubuntu, and that still works fine. It started with the computer freezing when loading Team Fortress 2. Alt-Tab and Ctrl-Alt-Del have no effect, and the hard drive does not make any sound. I tried to verify the game data using Steam and that freezes the computer too. So I stupidly reinstalled the game. Now the game doesn't freeze when it starts, but instead the whole computer randomly freezes. This computer is a Dell XPS M1530 with a 320GB (298GiB) drive (WDC WD3200BEVT-7) split 5-ways, with Windows and Linux a partition each, one more for Linux swap space, and another two partitions for Dell diagnostic program and factory image and drivers. There was once where the hard drive would make clicking noises all day, and only stopped when I rebooted the computer. Since then, the BIOS diagnostics would fail the drive (for "self-test log contains previous errors") whenever ran. (The on-disk diagnostics cannot be run because I overwrote the MBR with GRUB.) Naturally, I thought the hard drive could be the problem. CHKDSK found one bad sector, but this seems to have no effect. System File Checker found two protected files with wrong hashes, one is some kind of IE manifest, and the other is a tcpmon.ini. Neither of them can be restored because their back up copy also have wrong hashes. Nothing about system failures in the event viewer. What should I do next?

  Read the article

• Restore a database with LDF file only

  - by Martin

  First of all, i know how stupid it is not to have a any backup. I can't help it, but i have to (try) to solve it. I have a transaction log (LDF) file from a SQL Server 2000 database that contains all transactions since the creation of the database. No truncation has been done. The MDF file is gone. Probably because of some disk failure. There is no backup. Not from the original database and not from the transaction log. I have tried to link the transaction log to a new clean database. But (ofcourse) that failed because SQL Server checks the identity of both files. I have read about software that can read the transaction log. ApexSQL seems to do that. I tried to install the trial version but it gives weird errors when trying to start the program. Anyone knows a solution for me? It may contain third party software, but i prefer a clean SQL Server solution.

  Read the article

• Ubuntu inside VirtualBox is slow

  - by Kapsh

  I am running an Ubuntu instance on VirtualBox inside XP. Here are the details: Host: Windows XP Pro Guest: Ubuntu 8.10 Total RAM: 3GB RAM For VM: 1GB Total Video Memory: 128MB Video Memory for VM: 40MB Hard Drive: 200GB Hard Drive for VM: 30GB Processor: 2.80GHz Core Duo The problem is that whenever I am inside the virtual machine, things seem so much slower in general. For example Firefox, Eclipse take longer to load, dragging windows show a lag etc. I have tried running Ubuntu before (not inside a VM) and it seemed fantastically fast. So I am disappointed to have to deal with this situation. But I need access to the XP partition without having to reboot and hence the attempt. I am surprised with the perceived slowness since the whole world seems to be doing virtualization and I cannot imagine everyone works on slow systems knowingly. My question is - is there something I should be doing to boost performance? Am I doing something wrong? This is my home machine and I am not sure if this is the right forum to ask. Thanks.

  Read the article

• Software for RAID Failure Alerts?

  - by QF_Developer

  I have two 256 GB Samsung 840 Pro SSD disks in a RAID 1 array. I would like to receive a notification if one of the disks in the array fails. Can anybody recommend an application I can install on the server to fire an email if such an event occurs? Here are some additional specs: Supermicro X9SCM-IIF motherboard utilising the hardware RAID controller. OS = Windows 2012 Standard Also is it possible to simulate a disk failure by pulling it out of the bay? SSDs appear to fail close together when in a mirrored config so I'd like to know ASAP if one goes down so I can swap them out with minimum delay. UPDATE 26th June 2013 ------------------------ None of the software that ships with the Supermicro X9SCM-* motherboards offer support for RAID monitoring. As has been pointed out here, these boards are built on an Intel chipset for RAID and so I installed Intel Rapid Storage Technology that supports automated email notifications on RAID failure http://www.intel.com/support/chipsets/imsm/sb/cs-020784.htm One small issue, the software only allows you to send email notifications without SMTP authentication. There's a bunch of different workarounds here: http://communities.intel.com/thread/30771

  Read the article

• How can I take browser screenshots at a higher resolution than my browser supports?

  - by user53575

  I need to take a screenshot of a website as it would appear on a very high resolution monitor... say 16000x12800 pixels. My laptop's screen has a native resolution of 1280x800. Basically, I need to simulate having a monitor resolution much higher than my monitor and video card actually supports. I want the screenshot of the site to look pretty much how it does when you hit CTRL MINUS (zoom out) in Firefox repeatedly, but without any loss of pixels due to scaling. How can I do this? Is there some way to use virtual machine software to simulate a super-high-res display? If not, is there some way to open a browser window bigger than the screen, and then capture its contents as a PNG somehow? Anything else that might work? Here was an answer: http://superuser.com/questions/120266/how-can-i-take-browser-screenshots-at-a-higher-resolution-than-my-browser-support But it doesn't work. Firefox remains in the resolution of the physical screen. The window blinks and shrinks back to normal resolution. Please Help!!

  Read the article

• Linux Centos 6 becomes unavailable from time to time - OS&network issue

  - by adoado0

  I am encountering following problem. There is one server (DL160 G5) running Centos 6.3 with default kernel 2.6.32-220.2.1.el6.x86_64 - at this point I'd like to add that issue appeared also at older version - 6.1 and older kernel (do not remember exactly which version). There is cPanel installed and from time to time it becomes unavailable (network connection). What I've checked is (via KVMoIP): load average is completely normal it does not lack memory or disk space when problem occurs no console notifications checked all access logs and there is no sign that it can be caused by a client script cannot even access local interface (127.0.0.1) or main IP address running tcpdump I can only see packets arriving to server - no responses all services seem to be running properly (mail,sql,http,ssh) checked crontab and all clients' crontabs too network port utilisation is low ( up to several Mbits) arriving packet rate is low - hundreds per second (according to tcpdump) console (via kvmoip) works fine, no lags there is no conntrack at this server there is no ipv6 at this server flushing iptables, unloading modules does not resolve problem restarting network does not resolve problem, no errors appear it also occurs when two sepearate networks are configured (and multiple gateways) as well as one IP, one default gw and one network is configured - so it seems network configuration independent it seems to repeat randomly (load,packet rate,bandwith usage,load independent) checked server with different rootkit detection tools - it seems to be clean server has been rebooted, it did not change anything there are no interface errors it apperas randomly can be once a week or several times per day It usually works fine after 1-15 minutes. What I can also check? It is definitely OS issue - there is traffic at interface only in one direction when problem occurs, can not even ping loopback. Any ideas? Recommended checks? Anything I did not checked above.

  Read the article

• USB Device Not Recognized (Mac)

  - by Nargis

  Fortunately, my Mac-pro also made one of my USB storage devices inoperable. My data loss in that USB device but such as another USB device and USB keyboard are unaffected. I have heard that my friend usually trigger this problem by having at least two devices plugged in - typically thumb drives/USB flash drives, and then once a second flash drive is plugged in that become unrecognized. I have only two USB ports and first I think port loose when I connect two USB devices. But later I found these hidden files (“.Spotlight-V100”, “.TemporaryItems”, “.Trashes”, and “._.Trashes”) are created by Mac OS. And before unrecognized that USB device I have deleted these files and my friend had also done the same action. Now I don’t want to test for next USB device to become unrecognized and I won’t deleted any hidden system file inside the flash drives. But I really want to know why these problems happened. Can I delete these hidden files when I only connect to virtual machine (Vista), because I used to delete all useless hidden files from USB flash drives? Any suggestions or thoughts to prevent this or alternative suggestions to fix the problem that take lossless would be much appreciated.

  Read the article

• Lost Windows 7 boot after EasyBCD with EFI

  - by drent

  I've got a Lenovo Y580 with a 64GB SSD and a 1TB HDD setup using GPT and setup to boot from (U?)EFI. I was trying to get my Linux Mint installation on the Windows boot manager using EasyBCD (I didn't realise EFI but it wiped my boot partition/loader and I cannot seem to get Windows back (and I still can't get a bootable Linux Mint). Using the System Recovery utility, Startup Repair can't "see" windows (it might be because I'm using a 7 Pro disk to recover Home Premium?). In command prompt, Bootrec tools don't do anything and bootsect can't run because it says that it's for BIOS only and I've booted with EFI. I can see the EFI data on the 200mb SSD partition using diskpart but I don't know how to add Windows back onto whatever bootloader I have/need. At the moment the only options I can see are: Do a fresh install of Windows and hope that the setup remains as fast as the default one (the SSD is some kind of cache for Windows but I can't quite see how it works given that the rest of the SSD is unpartitioned space). This seems like overkill given that Windows was working fine til EasyBCD deleted it. Try forcing BIOS mode and see if that somehow magically fixes things Try converting from GPT to MBR to try and use the bootrec/bootsect tools (and maybe back again) which seems like a really bad idea. Anyone have any ideas?

  Read the article

• LAN Webserver not accessible through PPTP VPN

  - by Joe

  I have this LAN Network with 10 clients and one server. The server has 4 virtual machines and a BIND DNS Server. When the router assigns an IP through the DHCP , it also gives the ip of the DNS Server, to resolve internal domains. Everything apparently works fine, the clients being able to access the server's vm's resources, but I also have to create the possibility of remote access. I installed the PPTP VPN on the server, and the vpn clients would get the same ip address range as the router's dhcp is assigning. Apparently everything is fine here also, except the fact that when we connect through the vpn , we cannot access the webserver on port 80 ( the webserver being one of the server's VM ). The iptables on the webserver has been turned off for testing purposes and the router's firewall is directing all the external traffic to the server. Can somebody suggest a solution to this? Extra details : VPN Server : PPTP Server Centos 6.3 x64 VPN Client : Windows 7 default PPTP VPN Connection The client is successfully connected to the server, everything works ( FTP/MYSQL/SSH/DNS ) , except the fact that when I try to access the webserver IP on the browser, it won't work.Pinging it works perfectly.

  Read the article

• Cannot get at data in my NAS

  - by Ben

  I've got a bit of an issue that I'm hoping you can help me with. I have an Iomega ix4 as my NAS. This runs Linux and each drive in the box has 2 partitions: one for the OS and RAID info, and the second for the actual data. I had it configured as RAID5. Recently one of the drives failed. At this point all of the data was available, it was just reporting a failed drive. I had a drive of the same capacity (although not the exact same spec) which I swapped in place of the failed drive. It recognised it, and started to rebuild the data protection. So far so good ... or so I thought. The next day, after data protection had finished reconstructing, the NAS was telling me that 4 new drives had been added, and wanted confirmation to overwrite the data. Obviously I declined to do this. I swapped the failed drive back in again, in the hope that it would return to its previous state of the data being accessible, but one failed disk. However it didn't - it still tells me that the NAS has 4 new drives in it. I am hopeful that the actual data is untouched, so what I need to do is get it to rebuild the RAID without touching the data on the disks. I have ssh access, and have run stuff like mdadm --examine to see what I can find. The mdadm.conf file has no entry in the "definitions of existing MD arrays" section. I have not run any actual rebuilding commands as yet, because this is entering an area which I am out of my depth in. Please can someone advise the best way of getting my data? Thanks.

  Read the article

• Windows 8 install from USB freezes

  - by Rafael Almeida

  I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

  Read the article

< Previous Page | 622 623 624 625 626 627 628 629 630 631 632 633  | Next Page >