Search Results

Search found 24933 results on 998 pages for 'arch linux'.

Page 640/998 | < Previous Page | 636 637 638 639 640 641 642 643 644 645 646 647  | Next Page >

  • multicast and iptables

    - by Massimo
    I have secured a linux box, starting with iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP and after adding rules to enable specific protocols and streams. Which are the correct rules to add multicast support ? I am trying with these - for both client and server multicast : iptables -A INPUT -m pkttype --pkt-type multicast -j ACCEPT iptables -A OUTPUT -m pkttype --pkt-type multicast -j ACCEPT iptables -A INPUT --protocol igmp -j ACCEPT iptables -A OUTPUT --protocol igmp -j ACCEPT iptables -A INPUT --dst "224.0.0.0/4" -j ACCEPT iptables -A OUTPUT --dst "224.0.0.0/4" -j ACCEPT Linux 2.6.38-12 / iptables 1.4.10 Is there any internet service to test my multicast set ( pc + adsl router + provider ) ?

    Read the article

  • Banshee gapless playback does not work when playing mp3s

    - by ComputerGuy505
    Even though I have gapless playback enabled in Banshee's settings menu, there is a very short pause between songs. This might be due to the fact that my hard drive's partitions seem wierd. fdisk -l produces this output: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x4a73c3cb Device Boot Start End Blocks Id System /dev/sda1 * 2048 409599 203776 7 HPFS/NTFS/exFAT /dev/sda2 409600 724153740 361872070+ 7 HPFS/NTFS/exFAT /dev/sda3 1456826368 1465145343 4159488 c W95 FAT32 (LBA) /dev/sda4 724154366 1456826367 366336001 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 1440159744 1456826367 8333312 82 Linux swap / Solaris /dev/sda6 724154368 1440159743 358002688 83 Linux Partition table entries are not in disk order Playing mp3's from /dev/sda2 or /dev/sda6 produces this problem. I don't seem to have gapless playback on Rhythmbox or Clementine either, if those media players are supposed to have it. I'm not sure what other info to provide. This is just annoying to me. Thanks for any help.

    Read the article

  • MS Windows issue - "Filename or extension is too long"

    - by Daniel
    I run Microsoft windows on a few of my machines. I don't know if many people know about this issue in the OS but you can't have very long filenames, from what I know Linux can have longer names, I have never run into this issue on my Linux machines. Anyway I run into issues whenever copying folders & files to backup drives. I manually backup of my data, finding and changing names of files, this is very very tedious. Is there a software tool to shorten folders or filenames that are found to be to long on Windows? I have drive image duplication software which does the job but in a way that I don't like, plus moving files can become a hassle at times if the names are too long to copy.

    Read the article

  • What could be wrong with my CD drive and how do you fix it?

    - by Jamie
    My CD drive hasn't worked in about 8 months. I was burning CDs in a hurry and pulled it out because it was taking too long (probably an average amount of time). Im running a laptop (Toshiba Satellite A505-6965) that uses a slot drive. Now my computer doesn't accept CDs. It used to pull them in but it doesn't anymore. Ive heard it make odd noises a few times but thats it. The slot is these spongey things and Ive managed to peek into the drive with a flashlight and theres nothing in the way, really. Could someone explain the mechanics of what happened and if it would be possible to fix it? If itd be possible to fix it through Linux that would be great since I keep getting the BSOD (0x0000007B) and am going to try reinstalling Windows 7. But I can't really do that since I don't have a USB drive larger than 2 GB (Windows is about 4 GB) so Im relying on Linux ATM.

    Read the article

  • Running IPv4 program in IPv6 network

    - by stobyer
    I have an IPv4 windows client program and IPv4 Linux server. What I need is to run them in pure IPv6 network, although machines have dual stack. At the beginning I thought it's not a problem: I'll use 4in6 protocol (rfc2473) and that's all. I found a simple guide for Linux configuration here, but when I started to configuring windows 7, I couldn't find how to do it. There are plenty of info on how to tunnel IPv6 over IPv4 (6in4, Teredo) but not an opposite. Does anyone know how to do it? Thank you.

    Read the article

  • xubuntu 12.04 screen regularly stops refreshing, refreshing resumes after un-/re-maximizing a window

    - by user68477
    My screen frequently stops completely refreshing. I can make it resume refreshing by un-maximizing/re-maximize a window or by switching workspace (the un-/re-maximizing works every time. Switching workspace sometimes has to be done a couple of times). The immediate impression is that the system is frozen: there is apparently no reaction to anything I do but interestingly window title bar will change, if I switch application with (i.e alt+tab or browse through folders) I saw an identical issue in ubuntu 10.04, though a lot less frequent, I never saw this in ubuntu 12.04 (which I have been using the last 4-5 months). After switching to Xubuntu I'm seeing this again and more frequently. The specific reason I'm not sure this is a bug: I installed gnome-control-center which dragged in tons of packages. This was while trying to fix dual-screen setup. I believe the issue surfaced after this. I later meticulously removed every package from this batch (purge) in the hope that every setting would also be removed. But the issue has persisted. Another issue happened at the same time, it may be totally unrelated but it feels as if it is the same basic issue: the screen resolution of the greeter became less than the expected 1680x1050 and often after login there's just a blank and totally unresponsive wallpaper without panel so I have to force reboot. When the login is successful it's very clear that it works hard to determine the correct resolution which is achieved after a few blink to black screens. My questions: 1) Is this a settings issue or a bug? 2) How do I begin to research the issue - could I perhaps some way reset xubuntu/xfce to default. 3) If this is a bug where would be the most appropriate place report this? System: Thinkpad T500 ati radeon HD 3650 $ fglrxinfo display: :0.0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: ATI Mobility Radeon HD 3650 OpenGL version string: 3.3.11627 Compatibility Profile Context $ uname -a Linux srvname 3.2.0-32-generic #51-Ubuntu SMP Wed Sep 26 21:33:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux xfce 4.10 Compiz 0.9.7.8

    Read the article

  • How can I fix my xvinfo?

    - by YumYumYum
    How can i fix my X server/driver? $ xvinfo X-Video Extension version 2.2 screen #0 no adaptors present Additional info: $ uname -a Linux desktop 2.6.32-33-generic #70-Ubuntu SMP Thu Jul 7 21:13:52 UTC 2011 x86_64 GNU/Linux $ lspci 00:00.0 Host bridge: Intel Corporation Device 0100 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Sandy Bridge Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Device 1503 (rev 05) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4a (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 PCI bridge: Integrated Technology Express, Inc. Device 8892 (rev 10) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) Follow up: It seems in 64-bit its a mess doing existing approach. Therefore, after upgrading to 12.04 64-bit this problems in same hardware is resolved (of-course, i have now other drivers problem)

    Read the article

  • Why can't non-admin users install software?

    - by fiftyeight
    This is probably something I don't understand since I am used to Windows and am only starting out with Ubuntu. I know that software in linux comes in packages what I don't understand is why can't non-admin users install software. I mean, every application is run by a specific user, and that user will only be able to run that applciation with his privilages, so if he has no admin privileges, the application also won't be able to access unauthorized directories etc. I want most of the time to work on my PC with a non-admin user since it seems more safe to me, most of the time I have no need for admin privileges. and even though I know viruses in linux are uncommon I still think the best practice is to work on the computer in a state that you yourself can't make any changes to important files, that way viruses also can't harm any important files, but I need to install software for programming and web-design etc. and first of all I don't want to switch users all the time. But also it sounds safer to me that everything being done on the PC will be done through the non-admin user. I'll be glad to know what misunderstanding I have here, cause something here doesn't sound right.

    Read the article

  • Running a webserver behind a firewall, is it secure?

    - by i.am.intern
    Currently we have a Linux-based firewall which NAT-ing our public IP address to give internet access to our staff's PCs and a Windows Server 2003 for internal filesharing. I want to host Redmine/SVN (a bugtracker) internally behind this firewall using a Linux server. This webserver will be accessed by our clients externally so they can post bug reports. This means that I have to open port 80 & 22 at the firewall to give access to the webserver and me to SSH it from home. However, let's say I'm using password-based SSH for the webserver and somebody cracked it. Does that mean the cracker could ping and access other servers and PCs in the network?

    Read the article

  • -w test on OS X gives command not found error

    - by RobV
    I'm writing a bash script which I'm testing on OS X though it will ultimately run on a standard Linux environment and running into a weird error. I have tests like this in my script: if [ ! -w $BP ]; then echo "'$1' not writable" exit 1 fi Which seems pretty sane to me and works fine under Linux but when trying to test on OS X I get the following error message: startSvr.sh: line 135: [: missing `]' startSvr.sh: line 135: -w: command not found So is this a case of OS X not supporting the -w test or is there some other reason this isn't working for me? e.g. environment

    Read the article

  • Game crash/Screen freeze recovery (without shell or reboot)

    - by Asavar Tzeth
    I am an old Windows PC gamer, now converted into Ubuntu (Linux) lover. I am even going so far as to attempt to replace all my games in a Windows dual-boot with Wine and it is going well. However... Even if Linux is less prone to crashing, games, especially the windows ones (but also a few native) can crash. My problem is when this is in full screen and the computer becomes non-responsive. In Windows you can solve this with ctrl+alt+delete, but Ubuntu lacks this feature and my only choice is a reboot. Is there any Ubuntu version of this feature? Of course excepting the ctrl+alt+F1, find and kill process method. It is fine if you know how to do it, but too slow and difficult for the typical gamer. I believe strongly in Ubuntu as the future gaming platform in one form or another. If this feature does not exist, then the Ubuntu team should address this as fast as possible, since it is critical for all old Windows gamers. Thank you for your time. Asavar Tzeth (Alias)

    Read the article

  • How to disabled password authentication for specific users in SSHD

    - by Nick
    I have read several posts regarding restricting ALL users to Key authentication ONLY, however I want to force only a single user (svn) onto Key auth only, the rest can be key or password. I read How to disable password authentication for every users except several, however it seems the "match user" part of sshd_config is part of openssh-5.1. I am running CentOS 5.6 and only have OpenSSH 4.3. I have the following repos available at the moment. $ yum repolist Loaded plugins: fastestmirror repo id repo name status base CentOS-5 - Base enabled: 3,535 epel Extra Packages for Enterprise Linux 5 - x86_64 enabled: 6,510 extras CentOS-5 - Extras enabled: 299 ius IUS Community Packages for Enterprise Linux 5 - x86_64 enabled: 218 rpmforge RHEL 5 - RPMforge.net - dag enabled: 10,636 updates CentOS-5 - Updates enabled: 720 repolist: 21,918 I mainly use epel, rpmforge is used to the latest version (1.6) of subversion. Is there any way to achieve this with my current setup? I don't want to restrict the server to keys only because if I lose my key I lose my server ;-)

    Read the article

  • Is it safe to expect Sun Java 6 to supported for the life of RHEL 6?

    - by Ophidian
    I'm in the planning stages of a java application that we're targeting for Red Hat Enterprise Linux 6. Unfortunately, we're stuck at RHEL 6.1 which does not ship the java-1.7.0-oracle package set (they were added in 6.3) and I don't really have any control over when we will be upgraded to the more recent version. I don't have any specific technical requirements to use Java 7, but Java 6 is going to hit public EOL in February 2013. Am I safe to assume that since Red Hat (and subsequently Oracle with its Oracle Unbreakable Linux) has shipped a copy of Java 6 in the java-1.6.0-sun package, it will support it for the entire 10 year support life of RHEL6?

    Read the article

  • Cisco Router 1921

    - by mytempfw
    I'm very new in networking and I'm trying to setup my network as follow [ISP Modem/Router/Switch] + --- + {fxp0} [Linux Firewall] {fxp1} + --- + {??} [Cisco Router 1921] {GE 0/0} + --- + [Cisco Switch] + ... Servers {GE 0/1} + --- + [Cisco Switch] + ... Servers My questions are, Since I'm using both GE 0/0 and GE 0/1 ports to connect to switch, how can I connect my Linux Firewall (Port fxp1) to my Cisco Router? I know the USB and Console port are for configuration, can I use AUX port to connect my firewall (if so is it consider a right way)? Is my setup is right? if not can someone please explain to me to do the setup in right way. Link to the picture of my router: Cisco Router 1921 Thanks

    Read the article

  • Switch to another CPanel server, restore mailbox, how to stop Outlook POP3 pull mail data again.

    - by Shiro
    Hi, We switch from a linux CPanel server to another CPanel server, all the setting and file is restore back to the new Linux CPanel server. E.g [email protected] , inside the server I got 100mails. It had been downloaded to my Outlook, my outlook also got 100 mails inside. After I switch to new server, the 100 mail in the old server had been transfer to new server. However, when I open my Outlook, it start to download the 100 mails again, that means I got 200 mails in my mailbox and it is duplicated. How can I stop Outlook to download. The time stamp, receiver and sender is exactly the same. We want to keep a backup in the server, because we don't have a physical server to keep the mail. That why we would like to transfer the mailbox to the new server. Anyone have solution to stop Outlook download again?

    Read the article

  • I can't get grub menu to show up during boot

    - by wim
    After trying (and failing) to install better ATI drivers in 11.10, I've somehow lost my grub menu at boot time. The screen does change to the familiar purple colour, but instead of a list of boot options it's just blank solid colour, and then disappears quickly and boots into the default entry normally. How can I get the bootloader back? I've tried sudo update-grub and also various different combinations of resolutions and colour depths in startupmanager application with no success (640x480, 1024x768, 1600x1200, 16 bits, 8 bits, 10 second delay, 7 second delay, 2 second delay...) edit: I have already tried holding down Shift during bootup and it does not seem to change the behaviour. I get the message "GRUB Loading" in the terminal, but then the place where the grub menu normally appears I get a solid blank magenta screen for a while. Here are the contents of /etc/default/grub # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX=" vga=798 splash" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1"

    Read the article

  • Use crontab scheduling java application problem occurs

    - by koma
    The main method to start the java application. The main method initialize the log, and then determine whether the process is running. Every 10 minutes, scheduled to run through the linux crontab. Able to determine that the 10 minutes of this program must end. Under normal circumstances, will print the following log The beginning of the implementation of 10 minutes The end of the 10 minutes of normal The beginning of the implementation of 20 minutes The end of the 20 minutes of normal The beginning of the implementation of 30 minutes The end of the 30 minutes of normal ..... But now this situation: The beginning of the implementation of 10 minutes The end of the 10 minutes of normal Execution starts in 30 minutes, but detected already have a process in operation, the program exits. Start the execution of 40 points, but detected already have a process in operation, the program exits. ..... Very strange 20-minute log does not print, but the 20-minute program has been launched by the ps-ef | grep java view java thread, found in a 20-minute thread is locked. But why not see the log Check the linux dispatch log, not see scheduling a 20-minute log.

    Read the article

  • Ubuntu 14.04 says insufficient memory in my /boot memory alocation while updating

    - by Aravind Dollar
    I am new to Linux platform. I just tried installing Ubuntu alongside windows but allocated only 200 mb to the /boot partition which is not recommended. Now Ubuntu software update keep on insists me no enough space. What should I do? Is there any way to increase my /boot partition without removing the total OS? Or should I completely uninstall Ubuntu and put it back? Please anyone suggest me over this issue. I have no idea what to do. And please be elaborate, as I am new to Linux environment.

    Read the article

  • How can we best petition to bring Adobe creative software to Ubuntu?

    - by Sixthlaw
    Now I know its not as simple as asking for Adobe to support their design software on Ubuntu, but is there a way for the community and Canonical to make known to Adobe the rapidly growing amount of Linux users, and their desire for this great set of tools OFFICIALLY? I know that many of the answers I receive might be of the fashion "Its not going to happen", "use the free tools provided" or "Who knows it might happen in the near future", but this IS not what I am looking for. I have noticed, on sites like www.OmgUbuntu.com, there are links to pages where people can "like" the idea. Is there a way to try and get the whole community on board with this one, even Canonical, and as stated above, put forward this proposal to Adobe. The current requests for an Adobe CS, for Linux, are in dribs and drabs scattered all of the internet. Now is the best time to come up with productive solutions on how we can best gather statistics on the amount of people willing to buy the Adobe CS. These are the words of an Adobe employee: "I have forwarded this feedback on to the appropriate team who will consider it for future releases of Adobe software." The larger amount of people we have unified in the ONE community proposal, the greater chance we have of getting the software. How can we make this happen?

    Read the article

  • ftp server over internet using different port

    - by ???? ????
    I want to make my ftp server over the internet i made it on Debian linux computer and i changed the port of it to 201 my local ip is 192.168.1.3 so i can access it from any computer on my network through ftp :// mylocalip:201 it appear to me the login page i login with my linux user and can see the files on my ftp server to make it public i make port mapping on my router for port 201 when i try ftp :// mypublicip:201 it give me the login page and when i entered the login data it is loading infinity without open my ftp server files when i made it over default port 21 it works fine. can any one tell me what is the problem here?

    Read the article

  • Windows 8.1 - unfixable grub

    - by Nick
    I have a Gigabyte laptop that came with secure boot and windows 8. After a bit of battling, I managed to get my dual boot with Ubuntu 13.10.. Anyway, I upgraded zindows to 8.1, now grub is gone. I restarted from a live CD and chrooted to my drive. I used boot-repair multiple times (with successful output) both in default and with some advanced options; also reinstalled grub manually... Each time it tries once to boot to grub but gives a message for a very short amount of time. I recorded it and it is a regular bios message "Rebbot and Select proper Boot device of Insert Boot media in selected boot device and press a key" I even tried something called EasyBCD under winblows, it shows the correct boot options, but same there, it is unable to make the linux partition fire up. Anyway, no way to boot my linux box. Does anyone have an idea how to fix this? No need to redirect me to another post with grub reinstall or boot-repair, seen them all... I am thinking of trying this other boot loader, refind, to see if it works http://www.rodsbooks.com/refind/index.html Also re-reading this bios message, I'm thinking my partition might not have a boot flag anymore... I'll try that too with parted. Although both grub and win 8 are supposed to fire up from the same boot partition (the EFI one) Please help! thx

    Read the article

  • How do I get 1366x768 resolution on 12.04?

    - by Megan
    I am on an HP Envy 14, and the proper resolution that I should be using is 1366x768. This is not an option and I am stuck on 1024x768. I am using Linux 12.04. lspci | grep VGA: 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Madison [Radeon HD 5000M Series] I've tried to add the resolution as a mode in xorg.conf but that does not work. Please any help would be appreciated. I'm new to Linux and just got my dual boot working but this resolution issue is killing me. Edit1 I just tried using the xrandr command: xrandr --newmode "1368x768_60.00" 85.25 1368 1440 1576 1784 768 771 781 798 -hsync +vsync But I get an error: xrandr: Failed to get size of gamma for output default Edit2 lsmod returns the following: Module Size Used by vesafb 13844 1 rfcomm 47604 12 bnep 18281 2 parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 arc4 12529 2 joydev 17693 0 hid_logitech_dj 18594 0 i915 472941 5 uvcvideo 72627 0 usbhid 47199 1 hid_logitech_dj hid 99559 2 hid_logitech_dj,usbhid psmouse 87692 0 iwlwifi 332525 0 mac80211 506816 1 iwlwifi videodev 98259 1 uvcvideo snd_hda_codec_idt 70795 1 mei 41616 0 btusb 18288 2 v4l2_compat_ioctl32 17128 1 videodev hp_accel 25976 0 lis3lv02d 19876 1 hp_accel hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi input_polldev 13896 1 lis3lv02d drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 serio_raw 13211 0 snd_hda_intel 33773 5 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec bluetooth 180104 23 rfcomm,bnep,btusb cfg80211 205544 2 iwlwifi,mac80211 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec mac_hid 13253 0 snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_ra wmidi,snd_seq,snd_timer,snd_seq_device wmi 19256 1 hp_wmi video 19596 1 i915 intel_ips 18174 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 I have installed ATI/AMD proprietary FGLRX graphics driver. But there is another one called ATI/AMD proprietary FGLRX graphics driver (post-release updates) which I have trouble installing because it gives me an error and tells me to look at some sort of jockey log.

    Read the article

  • eSTEP Newsletter November 2011 now available

    - by uwes
    Dear Partners,We would like to inform you that the November issue of our Newsletter is now available.The issue contains informations to the following topics:Notes from Corporate: Magic Quadrant for Enterprise Application Servers, Oracle Buys RightNow Technical Corner: Oracle Solaris 11 – The First Cloud OS, Oracle Solaris 10 8/11 now available, New RAC/Containers certifications, DTrace and Container for Oracle Linux, Oracle Enterprise Manager Ops Center released, News from the Oracle Solaris Cluster, SPARC - New roadmap, T-Series Benchmarks Learning & Events: eSTEP Events Schedule, Recently Delivered TechCasts, Delivered Campaigns in 2011 How to ...: About Oracle Solaris Containers, Detailed feature comparison between the different versions of database 11g, Upgrade Advantage Program + table with examples, Sun Software Name ===> New Oracle Name, Oracle Linux and OVM Certification Search, TO YOUR ATTENTION - Repricing Servers and Xoptions You find the Newsletter on our portal under eSTEP News ---> Latest Newsletter. You will need to provide your email address and the pin below to get access. Link to the portal is shown below.URL: http://launch.oracle.com/PIN: eSTEP_2011Previous published Newsletters can be found under the Archived Newsletters section and more useful information under the Events, Download and Links tab. Feel free to explore and any feedback is appreciated to help us improve the service and information we deliver.Thanks and best regards,Partner HW Enablement EMEA

    Read the article

  • Why do most routers not include local DNS?

    - by user785194
    I need to change my firewall/router, and I'd prefer something with built-in DNS to resolve queries on the local subnets. I've got a mixed Linux/Windows system, often with only one computer turned on, and I frequently have problems resolving local names. I don't want to keep a Linux box permanently on just for DNS, and I'd prefer to have DNS in my router appliance, which is always on. I search Google for this occasionally but never find anything. You always get the obvious answers - it's not possible, put everything in /etc/hosts, NetBIOS, dedicated box, etc. So what am I missing? Why don't "cheap" routers let you do this? I'm pretty sure that Cisco kit does this. Almost all cheap routers will let you do MAC address reservation, to let them assign static IP addresses for DHCP. So why can't they simply do DNS as well for everything on the local subnets, just passing through remote domains to the ISP?

    Read the article

< Previous Page | 636 637 638 639 640 641 642 643 644 645 646 647  | Next Page >