Search Results

Search found 19878 results on 796 pages for 'multiple dispatch'.

Page 642/796 | < Previous Page | 638 639 640 641 642 643 644 645 646 647 648 649  | Next Page >

• Windows 2008 R2 Servers Sending Arp Requests for IPs outside Subnet

  - by Kyle Brandt

  By running a packet capture on my my routers I see some of my servers sending ARP requests for IPs that exist outside of its network. For example if my network is: Network: 8.8.8.0/24 Gateway: 8.8.8.1 (MAC: 00:21:9b:aa:aa:aa) Example Server: 8.8.8.20 (MAC: 00:21:9b:bb:bb:bb) By running a capture on the interface that has 8.8.8.1 I see requests like: Sender Mac: 00:21:9b:bb:bb:bb Sender IP: 8.8.8.20 Target MAC: 00:21:9b:aa:aa:aa Target IP: 69.63.181.58 Anyone seen this behavior before? My understanding of ARP is that requests should only go out for IPs within the subnet... Am I confused in my understanding of ARP? If I am not confused, anyone seen this behavior? Also, these seem to happen in bursts and it doesn't happen when I do something like ping an IP outside of the network. Update: In response to Ian's questions. I am not running anything like Hyper-V. I have multiple interfaces but only one is active (Using BACS failover teaming). The subnet mask is 255.255.255.0 (Even if it were something different it wouldn't explain an IP like 69.63.181.58). When I run MS Network Monitor or wireshark I do not see these ARP requests. What happens is that on the router capturing I see a burst of about 10 requests for IPs outside of the network from the host machine. On the machine itself using wireshark or NetMon I see a flood of ARP responses for all the machines on the network. However, I don't see any requests in the capture asking for those responses. So it seems like maybe it is maybe refreshing the arp cache but including IPs that outside of the network. Also when it does this NetMon doesn't show the ARP requests?

  Read the article

• Port Forwarding failing only to Ubuntu servers from Draytek router

  - by Rufinus

  I know this is a kinda unusal question, but Draytek support (..which is very eager to solve the issue) seems to reach its limits. Scenario: Draytek Vigor Multiwan router with current firmware. Multiple WAN IP Aliases on one of the wan ports DMZ (or port forwarding doesnt matter) from wan ip alias to internal host currently i have two internal hosts: 192.168.0.51 (Ubuntu) 192.168.0.53 (Debian) both should be accessible from outside via one of the wan ip aliases. both are accessible with their internal ip's at all times (!) If the router gots restartet, both external ips are forwarding to its internal hosts. But after a few minutes up to 2 hours, the ubuntu host is no longer reachable via its external interface. The debian hosts on the other hand is reachable. In what does ubuntu differs from debian ? I know at least of one user with the exact same problem. see http://ubuntuforums.org/showthread.php?p=10994279 Any ideas ? TIA EDIT: via ping diagnostics directly on vigor, 192.168.0.53 is pingable, 192.168.0.51 is not. but both hosts are perfectly reachable from anywhere inside the network. if i restart ubuntu networking it works again for a short time.... i'm out of ideas.. EDIT 2: after further investigation, i noticed a ping from .51 to the network (or a host in the internet) is enough to make the port-forwarding working again. So i will add an Cronjob as a "keep-alive" ping. This will solve the problem, but the reason for this behaivor is still in the dark. Thanks to all commentors.

  Read the article

• IIS 8 URL Redirect on site level

  - by jackncoke

  I am trying to do a simple 301 perm redirect to another url in IIS 8. The end results would be if i navigated to domain2.com i would end up on domain1.com. We are moving from IIS 6 to a new server and have aprox 600+ sites that will be configured on this IIS 8 box. All of these sites run a property CMS and are looking at the same directory for source code. In IIS 6 i would just go to the Home directory tab of each site and check the box that says "Permanent Redirect" and provide a URL. With IIS 8 there is "HTTP Redirect" and this looks like it would do the trick but it is being applied to all the sites in IIS 8. Not on the site level like it use to be in IIS 6. I also looked into URL Rewriting module for IIS 8 but it seems to take rules in the style of a firewall and i am not sure if i could effectly create rules that would cater to 600+ sites. I am looking for the easiest way to have redirects on my site level so that that customers with multiple domains can have there sites redirect to there main domain for seo purposes. I feel like this was so easily achieved in IIS 6 that i must be overlooking something in the new version.

  Read the article

• FTP FileWatcher

  - by Meiscooldude

  So, I am in this little predicament where I am stuck watching a few ftp folders to see if they have new files added to them. If they do, it needs to throw an event with the file name. Thereby telling something else to download that file. This is a pretty simple object to make, I was just curious if anyone knew how expensive this operation would be? I plan on using the command NLIST because I don't need file size information, and there will be no sub-directories in the folder. Each file in the folder will have exactly 25 characters in its name. There could be anywhere from 10 to 'maybe' a couple thousand (max around 2000) files per folder (usually on the lower end, 100-300, but currently growing). The files are anywhere from 250kb to a very VERY unlikely 10mb (usually within the 250kb to 4mb range). There possibly could be up to a few hundred folders (in which case I could change the watch frequency depending on number of folders), but currently there are only a few (6-10ish). There also would be multiple logins for the ftp server, different logins would have access to different folders. I am not asking for an implementation, just if anyone has some first or second hand knowledge about FTP, how could this affect my network. I am not opposed to putting in file retention times or change the frequency in which I check for new files.

  Read the article

• How should I set up protection for the database against sql injection when all the php scripts are flawed?

  - by Tchalvak

  I've inherited a php web app that is very insecure, with a history of sql injection. I can't fix the scripts immediately, I rather need them to be running to have the website running, and there are too many php scripts to deal with from the php end first. I do, however, have full control over the server and the software on the server, including full control over the mysql database and it's users. Let's estimate it at something like 300 scripts overall, 40 semi-private scripts, and 20 private/secure scripts. So my question is how best to go about securing the data, with the implicit assumption that sql injection from the php side (e.g. somewhere in that list of 300 scripts) is inevitable? My first-draft plan is to create multiple tiers of different permissioned users in the mysql database. In this way I can secure the data & scripts in most need of securing first ("private/secure" category), then the second tier of database tables & scripts ("semi-private"), and finally deal with the security of the rest of the php app overall (with the result of finally securing the database tables that essentially deal with "public" information, e.g. stuff that even just viewing the homepage requires). So, 3 database users (public, semi-private, and secure), with a different user connecting for each of three different groups of scripts (the secure scripts, the semi-private scripts, and the public scripts). In this way, I can prevent all access to "secure" from "public" or from "semi-private", and to "semi-private" from "public". Are there other alternatives that I should look into? If a tiered access system is the way to go, what approaches are best?

  Read the article

• Tips and Suggestions IP Address Re-Addressing?

  - by RSXAdmin

  Hello serverfault Universe, My ever evolving and expanding local area network is currently using a class-C address. My network consists of multiple subnets depending on site/location. 192.168.1.x is site HQ 192.168.5.x is secondary site 192.168.10.x is so on and so forth. Long story short - I have inherited this network design from the previous admin who has left the company which started off with a dozen people and now has just over 300 full time/part time employees. We do not yet have client VPN access; but we do have site to site VPN setup. My question is, in preparation for outside client access to my network via Cisco ASA, I would like to re-address the HQ site because I understand a 192.168.1.x or 192.168.0.x are not very good choices for a company subnet - it may conflict with a home user's LAN when connecting to my LAN, I believe? Through your experience, does anyone out there have any suggestions and tips on how I can proceed with re-addressing my subnets. If I designed this network I would have gone with a 10.0.0.0 (mask 255.255.255.0) so I am leaning towards changing it to fit. Thank you.

  Read the article

• Do any well-known CAs issue Elliptic Curve certificates?

  - by erickson

  Background I've seen that Comodo has an elliptic curve root ("COMODO ECC Certification Authority"), but I don't see mention of EC certificates on their web site. Does Certicom have intellectual property rights that prevent other issuers from offering EC certificates? Does a widely-used browser fail to support ECC? Is ECC a bad fit for traditional PKI use like web server authentication? Or is there just no demand for it? I'm interested in switching to elliptic curve because of the NSA Suite B recommendation. But it doesn't seem practical for many applications. Bounty Criteria To claim the bounty, an answer must provide a link to a page or pages at a well-known CA's website that describes the ECC certificate options they offer, prices, and how to purchase one. In this context, "well-known" means that the proper root certificate must be included by default in Firefox 3.5 and IE 8. If multiple qualifying answers are provided (one can hope!), the one with the cheapest certificate from a ubiquitous CA will win the bounty. If that doesn't eliminate any ties (still hoping!), I'll have to choose an answer at my discretion. Remember, someone always claims at least half of the bounty, so please give it a shot even if you don't have all the answers.

  Read the article

• unreadable corrupted ntfs partition - lost clusters reported

  - by Eduardo Martinez

  Hi, partition magic is reporting multiple 'bad file record signature' and 'lost clusters' errors on my 250GB samsung sata disk (connected via usb on a xp sp3). Unfortunately PM is unable to fix. PM shows the drive as being NTFS, detects used space ok and also drive name. But PM browser (right click on partition, browse...) won't show anything (as if disk was empty) Windows Explorer is not even picking the drive name and reports 'the file or directory is corrupted and unreadable' PTDD partition table doctor demo tells me the boot sector is fine, and I can see all disk content on its browser - but crucially cannot copy that content over to a new disk (PTDD browser is pretty arid to say the least) Also tried - photorec-6.11.3 - it actually started to extract files but wouldn't keep file names or any folder structure (maybe I missed sth on the configuration options) - find and mount - intellectual scan went well, the only partition on the disk was detected, then tried to mount into p: but got this error on windows explorer: 'p:\ is not accesible. The media is write protected'. Find and mount allows you to create an image from partition but I don't have a disk big enough at hand. Does anyone know if this will keep the extracted files/folders structure intact? I'm starting to think the disk is pretty screwed and my chances to recover this data are slim. Please someone enlighten me with that marvellous piece of software I am missing :-) Thanks in advance

  Read the article

• Linux - real-world hardware RAID controller tuning (scsi and cciss)

  - by ewwhite

  Most of the Linux systems I manage feature hardware RAID controllers (mostly HP Smart Array). They're all running RHEL or CentOS. I'm looking for real-world tunables to help optimize performance for setups that incorporate hardware RAID controllers with SAS disks (Smart Array, Perc, LSI, etc.) and battery-backed or flash-backed cache. Assume RAID 1+0 and multiple spindles (4+ disks). I spend a considerable amount of time tuning Linux network settings for low-latency and financial trading applications. But many of those options are well-documented (changing send/receive buffers, modifying TCP window settings, etc.). What are engineers doing on the storage side? Historically, I've made changes to the I/O scheduling elevator, recently opting for the deadline and noop schedulers to improve performance within my applications. As RHEL versions have progressed, I've also noticed that the compiled-in defaults for SCSI and CCISS block devices have changed as well. This has had an impact on the recommended storage subsystem settings over time. However, it's been awhile since I've seen any clear recommendations. And I know that the OS defaults aren't optimal. For example, it seems that the default read-ahead buffer of 128kb is extremely small for a deployment on server-class hardware. The following articles explore the performance impact of changing read-ahead cache and nr_requests values on the block queues. http://zackreed.me/articles/54-hp-smart-array-p410-controller-tuning http://www.overclock.net/t/515068/tuning-a-hp-smart-array-p400-with-linux-why-tuning-really-matters http://yoshinorimatsunobu.blogspot.com/2009/04/linux-io-scheduler-queue-size-and.html For example, these are suggested changes for an HP Smart Array RAID controller: echo "noop" > /sys/block/cciss\!c0d0/queue/scheduler blockdev --setra 65536 /dev/cciss/c0d0 echo 512 > /sys/block/cciss\!c0d0/queue/nr_requests echo 2048 > /sys/block/cciss\!c0d0/queue/read_ahead_kb What else can be reliably tuned to improve storage performance? I'm specifically looking for sysctl and sysfs options in production scenarios.

  Read the article

• Coming from Win XP to 7 and having new accessibility software problems

  - by Anonymous Jones

  I just switched from Windows XP Pro SP3 (32bit) to Windows 7 Ultimate (32bit) on a new PC. Now, both the new onscreen keyboard and a utility for sending mouse clicks are being problematic. The problem with 7's OSK is that some things I type only work intermittently or just dodgily. Like Alt+Tab with multiple Tabs, other Alt/Ctrl/Shift/Win key combinations, and the context menu key. Sometimes apps will not take focus for input at all. I use the OSK it in 'hover' mode, on 0,5 seconds. The clicking tool is Point-N-Click, which sends clicks when I dwell anywhere for 1.25 seconds with the mouse pointer. http://www.polital.com/pnc/ The problem with it is that sometimes it fails to click. Most often this happens in some of the control panel sections, on the taskbar, and when UAC pops up. It seems to occur in conjunction with OSK usage a bit too, I think. I'm using an Administrator account. DEP and UAC settings are default. What can I do to fix or work around either of these problems? I'm disabled so this really is killing usability.

  Read the article

• One-To-Many Powershell Scripts

  - by Matt

  I'm trying to create a script to run as a scheduled task, which will run against multiple servers and retrieve some information. To start with, I populate the list of servers by querying AD for all servers that match a certain set of criteria, using Get-ADComputer. The problem is, the list is returned as an object, which I can't then pass to the New-PSSession list. I have tried converting it to a comma-seperated string by doing the following: foreach ($server in $serverlist) {$newlist += $server.Name + ","} but this still doesn't work. the alternative is to iterate through the list and run the various commands against each server one at a time, but my preference would be to avoid this and run them using one-to-many remoting. UPDATE: To clarify what I want to end up being able to do is using -ComputerName $serverlist, so I want $serverlist to be a string rather than an object. UPDATE 2: Thanks for all the suggestions. Between them and my original method I'm starting to wonder whether -ComputerName can accept a string variable? I've got varying degrees of success getting the list of computers converted to a comma separated string, but no matter how I do it I always get invalid network address.

  Read the article

• How do I load balance between two Linux machines?

  - by William Hilsum

  Inspired by the Stack Overflow network, I am now obsessed with HAProxy and trying to use it myself. At the moment, each HAProxy box has got two network cards (well, two configured, I can have a maximum of 4 and wasn't sure if they needed their own one for management between the boxes). On both machines, the backend one (eth1) is a private IP that goes to a switch connected to the webservers, and the front facing one (eth0) has a public internet IP that is routed straight though. In addition, I have created an additional virtual ip for eth0 called eth0:0 which has got a third public ip address. I just about get how to use it for load balancing between multiple web servers that are behind it, but, I am failing to load balance between the two HAProxy boxes - they appear to fight for the virtual IP, but, this does not appear to be a smart solution. Now, by using the virtual shared IP address, this solution appears to work and does seem to give me maximum uptime, but, is this the correct way to do it, or is there a smarter way? I have been looking at other Linux packages such as keepalived, but, I have only been using Linux (server) for a week now and am at the limits of my understanding. Is there anyone who has done this before and can you advise anything for maximum uptime?

  Read the article

• VPN Client solution

  - by realtek

  I have several VPN's that I need to establish on a daily basis but from multiple workstations. What I would like to do it have either a server or vpn router that can perform this connection itself and that I can then route traffic through this device or server depending on the subnet I am trying to reach. The issue is that I only use VPN Clients to connect, so I am basically trying to achieve almost a site to site VPN but by using basically a VPN Client type connection from my network. The main VPN Client I use is the Sonicwall Global VPN Client where I initially use a Preshared Key and then it always prompts me for a username and password (not RSA key). My question is, is there any type of linux distro or even a hardware vpn router that can do this and connect to a Sonicwall device as if it were a client? I have tried pfSense which is very good but it fails to connect, probably due to a mismatch of settings. I have tried many others. Even dd-wrt on my router but it does not support whatever protocol Sonicwall uses. (I thought L2TP/IPSec) but it appears it may not be that. Any advice would be great! The other other thing I have thought of that I have not tried yet is Windows Server Routing and Remote Access but I have a feeling that won't work either. Thanks

  Read the article

• Bash Parallelization of CPU-intensive processes

  - by ehsanul

  tee forwards its stdin to every single file specified, while pee does the same, but for pipes. These programs send every single line of their stdin to each and every file/pipe specified. However, I was looking for a way to "load balance" the stdin to different pipes, so one line is sent to the first pipe, another line to the second, etc. It would also be nice if the stdout of the pipes are collected into one stream as well. The use case is simple parallelization of CPU intensive processes that work on a line-by-line basis. I was doing a sed on a 14GB file, and it could have run much faster if I could use multiple sed processes. The command was like this: pv infile | sed 's/something//' > outfile To parallelize, the best would be if GNU parallel would support this functionality like so (made up the --demux-stdin option): pv infile | parallel -u -j4 --demux-stdin "sed 's/something//'" > outfile However, there's no option like this and parallel always uses its stdin as arguments for the command it invokes, like xargs. So I tried this, but it's hopelessly slow, and it's clear why: pv infile | parallel -u -j4 "echo {} | sed 's/something//'" > outfile I just wanted to know if there's any other way to do this (short of coding it up myself). If there was a "load-balancing" tee (let's call it lee), I could do this: pv infile | lee >(sed 's/something//' >> outfile) >(sed 's/something//' >> outfile) >(sed 's/something//' >> outfile) >(sed 's/something//' >> outfile) Not pretty, so I'd definitely prefer something like the made up parallel version, but this would work too.

  Read the article

• Outlook won't re-connect to exchange after network is re-connected

  - by stan503

  I have a setup at my desk where I connect my computer to a an RJ45 switch that switches between two networks. One network is the corporate network, which is maintained by my company's IT, and the other is my own private network where I do testing (the two networks have to be separated). The corporate network hosts the exchange server where I get e-mail. When I switch from the private network to the corporate network, I expect Outlook to re-connect to the exchange server. However, I have found that sometimes when I come back, Outlook take an extremely long time to re-connect. Send/Receive will give me back the error 'The server is not available' (0x8004011D). It will sit there for 10 minutes to a few hours before it finally re-connects. The only other option is to reboot my computer, which is a huge pain for me since I run multiple VMs on it. This usually happens when I'm connected to the private network for a significant amount of time, so I'm thinking it's because Outlook has cached the network status. Is there a way to force Outlook to do a 'hard' re-connect to the exchange server? I'm using Windows XP SP 3 with Outlook 2007.

  Read the article

• nginx projects in subfolders

  - by Timothy

  I'm getting frustrated with my nginx configuration and so I'm asking for help in writing my config file to serve multiple projects from sub-directories in the same root. This isn't virtual hosting as they are all using the same host value. Perhaps an example will clarify my attempt: request 192.168.1.1/ should serve index.php from /var/www/public/ request 192.168.1.1/wiki/ should serve index.php from /var/www/wiki/public/ request 192.168.1.1/blog/ should serve index.php from /var/www/blog/public/ These projects are using PHP and use fastcgi. My current configuration is very minimal. server { listen 80 default; server_name localhost; access_log /var/log/nginx/localhost.access.log; root /var/www; index index.php index.html; location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www$fastcgi_script_name; include fastcgi_params; } } I've tried various things with alias and rewrite but was not able to get things set correctly for fastcgi. It seems there should be a more eloquent way than writing location blocks and duplicating root, index, SCRIPT_FILENAME, etc. Any pointers to get me headed in the right direction are appreciated.

  Read the article

• How can I get VirtualBox to run at 1366x768?

  - by Joe White

  I'm trying to run Windows 8 in VirtualBox. My laptop's display is exactly 1366x768. Windows 8 disables some of its features if the resolution is less than 1366x768, so I need to run the guest OS fullscreen. The problem is, VirtualBox refuses to run the guest at 1366x768. When VirtualBox is "fullscreen", the guest is only 1360x768 -- six pixels too narrow. So there's a three-pixel black bar at the left and right sides of the display. This user had the same problem, but the accepted answer is "install the Guest Additions", which I've already done; that got me to 1360, but not to 1366. According to the VirtualBox ticket tracker, there used to be a bug where the guest's screen width would be rounded down to the nearest multiple of 8, but they claim to have fixed the bug in version 3.2.12. I'm using version 4.1.18 and seeing the same problem they claim to have fixed, so either they broke it again, they were wrong about ever having fixed it, or my problem is something else entirely. This answer suggested giving the VM 128MB of video memory, and claimed no problems getting 1366x768 afterward. When I created the VM, its display memory was already defaulted to 128 MB. I tried increasing it to 256MB, but with no effect: the guest is still six pixels too narrow. My host OS is Windows 7 64-bit, and I'm running VirtualBox 4.1.18. How can I get VirtualBox to run my guest OS fullscreen at my display's native resolution of 1366x768?

  Read the article

• Copy/paste filtered column in Excel - error message

  - by hazymat

  Firstly I should state that I don't believe in spreadsheets; my normal mode of operation is that data should either exist in a database or a text file... However - employment requires... In short, I have filtered a worksheet by column A, and I want to copy/paste from column B to column C. Obviously I don't wish to copy/paste values from rows that were filtered-out here. The above sounds ridiculously simple, right? First I tried simply copy/pasting on the filtered worksheet. This appeared to select and copy only the filtered data, however pasting appeared to insert values into hidden/filtered rows - as you might expect. So my initial research suggests I may wish to select the filtered data and press Alt+; (that is, ALT plus semicolon), which is a shortcut key for Goto Special Select Visible. Then just copy-paste. CTRL+C correctly copies the filtered data, however when I go to paste the values into another column, it pastes into hidden rows as well. Okay, so perhaps I should also "Select Visible" on the cells I wish to paste into as well? Nope - that gives me the error That command cannot be used on multiple selections. What am I doing wrong?!

  Read the article

• Windows 2012 RDS Temporary profile for Administrator

  - by Fabio

  I've configured a Windows 2012 RDS Farm with two virtual servers (VMWare - each one on a different ESX server). Both servers have Licensing, Web Access, Gateway, Connection Broker and Session Host roles. High Availability is set up and it works fine. Remote Apps are working and even Windows XP clients have access to the web interface. User profile path is \vmfiles1\UserProfileDisks\App\ and almost everyone has full right access to it. The problem I have is that I would like to be able to access both servers at the same time with the Administrator account (console), but each time I try, the second server that I logon to give me access with a temporary profile. I tried to enable/disable multiple sessions per user and forced Admin logoff with the GPO but nothing changed. Another thing is that the server pool is not saved, so each time I restart the RDS server or I logoff from it, I have to add a server in the server manager. Do you have any idea? Sorry if my english is not perfect.

  Read the article

• pfSense router on a LAN with two gateways

  - by JohnCC

  I have a LAN with an ADSL modem/router on it. We have just gained an alternative high-speed internet connection at our location, and I want to connect the LAN to it, eventually dropping the ADSL. I've chosen to use a small PFSense box to connect the LAN to the new WAN connection. Two servers on the LAN run services accessible to the outside via NAT using the single ADSL WAN IP. We have DNS records which point to this IP. I want to do the same via the new connection, using the WAN IP there. That connection permits multiple IPs, so I have configured pfSense using virtual IP's, 1:1 NAT and appropriate firewall rules. When I change the servers' default gateway settings to the pfSense box, I can access the services via the new WAN IPs without a problem. However, I can no longer access them via the old WAN IP. If I set the servers' default gateway back to the ADSL router, then the opposite is true - I can access the services via the ADSL IP, but not via the new one. In the first case, I believe this is because an incoming SYN packet arrives at the ADSL WAN IP, and is NAT'd and sent to the internal IP of the server. The server responds with a SYN/ACK which it sends via its default gateway, the pfSense box. The pfSense box sees a SYN/ACK that it saw no SYN for and drops the packet. Is there any sensible way around this? I would like the services to be accessible via both IPs for a short period at least, since once I change the DNS it will take a while before everyone picks up the new address.

  Read the article

• How many reverse proxies (nginx, haproxy) is too many?

  - by Alysum

  I'm setting up a HA (high availability) cluster using nginx, haproxy & apache. I've been reading great things about nginx and haproxy. People tend to choose one or the other but I like both. Haproxy is more flexible for load balancing than nginx's simple round robin (even with the upstream-fair patch). But I'd like to keep nginx for redirecting non-https to https among other things right at the point of entry to the cluster. On the other hand, nginx is a lot faster for serving static contents and would reduce the load on the powerful apache which loves to eat a lot of RAM! Here is my planned setup: Load balancer: nginx listens on port 80/443 and proxy_forwards to haproxy on 8080 on the same server to load balance between the multiple nodes. Nodes: nginx on the node listens to requests coming from haproxy on 8080, if the content is static, serve it. But if it's a backend script (in my case PHP), proxy forward to apache2 on the same node server listenning on a different port number. Technically this setup works but my concerns are whether having the requests going through several proxies is going to slow down requests? Most of the requests will be PHP requests as the backends are services (which means groing from nginx - haproxy - nginx - apache). Thoughts? Cheers

  Read the article

• Want to use something like Citrix XenDesktop, Free Alternative?

  - by Chris

  I'm looking to go into IT, general office server management, and it looks like XenDesktop would be a awesome tool to use. If I get it right, you would store a central image of the OS you want to deploy (in an iso file) on the main server. Then use XenDesktop to pull that image down to the client, and it will then boot the OS inside of the virtual machine. Does it download the image of the OS and store it locally (like cloning the VM onto the client?) I'd love to find a free (possibly open source?) alternative to this, I keep on hearing about KVM in Linux and PXE booting a minimalistic OS to use remote KVMs.... Would that be what I'm looking for? Ideally, I'd like a system.. - That allows me to manage one central image for multiple clients (virtualized hardware) - Easily boot a thin client OS that connected to XenDesktop. Would those things be possible with some kind of free alternative? Some guidance would be greatly appreciated.

  Read the article

• KVM error with device pass through

  - by javano

  I am running the following command booting a Debian live CD passing a host PCI device to the guest as a test and KVM errors out; kvm -m 512 -boot c -net none -hda /media/AA502592502565F3/debian.iso -device pci-assign,host=07:00.0 PCI region 1 at address 0xf7920000 has size 0x80, which is not a multiple of 4K. You might experience some performance hit due to that. No IOMMU found. Unable to assign device "(null)" kvm: -device pci-assign,host=07:00.0: Device 'pci-assign' could not be initialized lspci | grep 07 07:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74) I shoved an old spare NIC into my motherboard to test PCI pass through. I have searched the Internet with Goolge and found that errors relating to "No IOMMU found" often mean the PCI device is not supported by KVM. Does KVM have to support the device being "passed-through"? I though the point was to pass the device through and let the guest worry about it? Ultimately I want to pass-through a PCI random number generator, is this not going to be possible with KVM? Thank you.

  Read the article

• Find out when a system went down?

  - by Clinton Blackmore

  I have a Mac OS X 10.5 server, with a RAID set in it, that went down due to a power outage on Thursday, and the machine is not happily booting right now*. It is possible to find out when the machine went down, while not booted off the internal drive? (I'm booted off an external drive, waiting for the RAID sets to initialize.) Normally, I'd run last. The man page doesn't indicate that I can run it against a different startup volume. It looks possible to parse /var/log/utmpx, but I don't think it'd be worthwhile to try to do that from scratch for this one-off problem. * I'm still trying to figure out why it isn't happy, and may ask a follow-up question. Right now I can see that UserNotificationCenter crashed repeatedly early Thursday morning, and that securityd, mdworker, and ARDAgent crash shortly after startup [I think -- I want to verify when the box went up and down]. The login window does not come up right (I think it is crashing or not able to cope with a dead securityd). The box is supposed to be set to go down when the UPS tells it power is out; at the moment, I'm wondering if it went down, and turned back on multiple times! I sure hope not.

  Read the article

• Errors with Using Webcam

  - by C.G.

  I have been having some issues accessing a webcam from my machine. Sometimes (not always) when I run a program that accesses the device (cheese, guvcview, and code using openCV), I get either of two messages, which lead to the program crashing. The first occurs after running the webcam for some time. libv4l2: error dequeuing buf: No such device VIDIOC_DQBUF: No such device The other will occur without even letting me have a chance to run the webcam. libv4l2: error turning on stream: No space left on device VIDIOC_STREAMON - Unable to start capture: No space left on device Occasionally after getting these errors I will also receive a message saying that no such device can be found for subsequent runs. Other than the times that the "No device found" message appears the webcam appears when I use lsusb. My machine runs Linux Fedora 16, and the webcam is a Logitech C920. I do have ffmpeg installed, and I have been able to run the web camera many times in the past without errors. What is particularly puzzling about these errors is that they just sprung up this past weekend. No new software or hardware has been installed on this machine recently; I haven't changed any settings recently either. It could possibly be a driver issue, but I don't know what could have changed which could lead to this issue. Any attempts at researching this problem has been fruitless as this seems to most commonly occur with multiple webcams. I am only working with one device. I'd appreciate any advice for this problem, as this has become a bit frustrating.

  Read the article

< Previous Page | 638 639 640 641 642 643 644 645 646 647 648 649  | Next Page >